004 ZXSDR NodeB Data Configuration_PPT-42

ZXSDR NodeB Data Configuration

ZTE University

Content

Overview

NodeB Configuration

Ground Resource Configuration

Transmission Resource Configuration

Wireless Resource Configuration

Overview--LMT Data Configuration Mode

On-line configuration This mode is to configure the ZDB of the B8200 directly. The data configured

on the line take effect immediately. To configure on the line, modify the contents in the C:\ump file first, to set the IP address as the IP address of the debugging network interface on the CC board of the B8200. Then, run the LMT. The CC board is defaulted before delivery.

Off-line configuration This mode is to modify the configurations on the client. The configurations are

saved into the designated directory in the mode of the XML file. In the off-line configuration, the LMT is not connected to the B8200 and the operation does not affect the running of the B8200. The off-line configuration mode is used when there is no ump file under the root directory of the Disc C. One local configuration file is required for the off-line configuration.

Node B Application Part

(NBAP)

Transport Layer

Radio Network Layer

Radio Network Control Plane

Transport Network

Control Plane

DC

H F

P

RA

CH

FP

Physical Layer

DS

CH

FP

Data Link

User Plane

SCTP

IP

FA

CH

FP

PC

H F

P

US

CH

FP

CP

CH

FP

Data Link

IP

UDP

Overview--Iub Interface Protocol Stack （ IPOE）

Overview--LMT Data Configuration Flow

IP Over FE Mode Transmission Data Configuration Flow :

Prepare

Plan parameters for

RNC interconnection

NodeB Configuration

NodeB basic

attributes

Rack and

board configuration

Serial port

configuration

clock referen

ce source

Ground resource configuration

Environment monito

ring

Dry contact configuration

Topology

structure

setting

Transmission resource

configuration

Ethernet

parameter

IP param

eter

Globe port Parameter

Static route param

ete

Wireless resource configuration

RRU Common Paramet

er

Base Band

Resource Pool

RF Connec

tion

WCDMA Sector

Local Cell

End

SCTP stream parameter

SCTPparameter

OMCB parameter

IP Clock parameter

BFD param

eter

Content

LMT Data Configuration

NodeB Configuration




NodeB Configuration

NodeB Basic Attributes Clock Reference Source Configuring Rack and Board

NodeB Configuration

Setting NodeB Basic Attributes :Basic Parameter and Other Relevant Parameters

NodeB Configuration

NodeB Configuration

Configuring Rack and Board : Create RRU rack

NodeB Configuration

Configuring Rack and Board : Create board on BBU and RRU rack

NodeB Configuration

Configuring Clock Reference Source : Right-click and choose Configuration Management BS Configure Clock Reference Source. Configure Clock Reference Source dialog box pops up.

Content


NodeB Configuration





Environment Monitoring In-line Tower Amplifier Serial Port Topology structure AISG Device Dry Contact


Configuring Environment Monitoring: click Configuration Management→ Ground Resource Management→ Environment Monitoring to open the Environment Monitoring window:


Configuring Topology Structure: Click Configuration Management→ Ground Resource Management→ Topology to open the Topology window.


Configuring Topology Structure:

About upper-level and lower-level in the topology configuration: The board/rack near the baseband processing unit is the upper-level The board/rack away from the baseband processing unit is lower-level.


Configuring Dry Contact

Content


NodeB Configuration





For the IP over FE transmission, the following nine items should be configured: Ethernet Parameter Global Port Parameter IP Parameter Static Route Parameter SCTP Parameter SCTP Stream Parameter IP Clock Parameter BFD Parameter OMC-B Parameter


Configuring Ethernet Parameter--Click Physical Media Configuration→ Ethernet parameter .Right-click the blank part in this pane and choose Add to open the Ethernet parameter management dialog box:


Configuring Global Port Parameter--Click Transmission Resource Management→ IP Bearing Configuration→ Global port parameter to open the Global port parameter pane. Right-click the blank part in this pane and choose Add to open the Global Port Parameter dialog box:


Configuring IP Parameter--Click Transmission Resource Management→ IP Bearing Configuration→ IP parameter to open the IP parameter pane. Right-click the blank part in this pane and choose Add to open the IP Parameter Management dialog box:


Configuring Static Route Parameter--Click Transmission Resource Management→ IP Bearing Configuration→ Static Router Parameter. Right-click the blank part in the right pane and choose Add to open the Static route configuration dialog box.


Configuring SCTP Parameter--Click Transmission Resource Management→ IP Bearing Configuration→ SCTP Parameter to open the SCTP parameter pane. Right-click the blank part in this pane and choose Add to open the SCTP parameter management dialog box:


Configuring SCTP Stream Parameter--Click Transmission Resource Management→ IP Bearing Configuration→ SCTP Stream Parameter to open the SCTP stream parameter pane. Right-click the blank part in this pane and choose Add to open the SCTP stream parameter management dialog box.


Configuring IP Clock Parameter--Click Transmission Resource Management→ IP Bearing Configuration→ IP Clock Parameter to open the IP Clock parameter pane. Right-click the blank part in this pane and choose Add to open the IP Clock parameter dialog box.


Configuring BFD Parameter--Click Transmission Resource Management→ IP Bearing Configuration→ BFD Parameter to open the BFD parameter pane. Right-click the blank part in this pane and choose Add to open the BFD parameter dialog box.


Configuring OMC-B Parameter

Content


NodeB Configuration





RF Connection RRU Common Parameter Base Band Resource Pool WCDMA Sector Local Cell


Configuring RF Connection--Click Wireless Resource Management→ RF Connection to open the RF Connection pane. Right-click the blank part in this pane and choose Add →Rack to open the RF Connection dialog box.


Configuring RRU Common Parameter --Click Wireless Resource Management→ RRU Common Parameter to open the RRU Common Parameter pane. Right-click the blank part in this pane and choose Add to open the RRU Common Parameter dialog box.


Configuring Baseband resource pool--Click Wireless Resource Management→ Baseband Resource Pool and right-click the blank part in this pane and choose Add to open the baseband resource pool Management dialog box:


Configuring Baseband resource--Click Baseband Resource Pool→ Baseband Resource to open the Baseband Resource pane. Right-click the blank part in this pane and choose Add to open the Baseband Resource dialog box:


Configuring WCDMA Sector--Click Wireless Resource Management→ WCDMA Sector to open the WCDMA Sector pane. Right-click the blank part in this pane and choose Add to open the WCDMA Sector dialog box:


Configuring Local cell--Click Wireless Resource Management→ WCDMA Sector to open the WCDMA Sector pane. Right-click the blank part in this pane and choose Add Local Cell to open the Local Cell Management dialog box:


Configuring Local cell

004 ZXSDR NodeB Data Configuration_PPT-42

Documents

Transcript of 004 ZXSDR NodeB Data Configuration_PPT-42