00 RFQ Civil ,RCC & Arch Works Rev

ABENGOA Abeinsa Infraestructuras Medio Ambiente, S.A. (Abeima)

Proposal no: Rajasthan Rural Water Supply and Fluorosis Mitigation Project (Nagaur) Chapter No. 1

P/L65/09/000407 Package 1 (TM-01) Page No.: 0

Request for Quotation for TM-01 Package

Client: Public Health Engineering Department, Rajasthan

Subject: Construction of 250 MLD WTP, 5310 ML RWR, RWPH, canal/channel, CWR, CWPS, at Nokha Daiya, SCADA system for complete Phase II and transmission pipeline of 1900 mm MS from Nokha Daiya to Deshnok

Title: RFQ for Civil, Structural & Architectural works

Document: RFQ for Civil, Structural & Architectural works- TM-01 package

Revision: "00"

Date: January, 2015

Issued by:

SSS

Checked by:

KSB

Approved by:

BM

© This procedure is the sole property of Abener Energía S.A. The total or partial reproduction, by any means, as well as its distribution to third parties without the express written permission of Abener is strictly forbidden.




Revision Control Sheet

Revision Date (DD/MM/YYYY) Revision Object

00 09/01/2015 Initial Issue




Table of Content

1 General ................................................................................................................................ 4 2 Site Data ............................................................................................................................... 4 3 Climatic Data ........................................................................................................................ 6 4 Environmental Protection Requirements ................................................................................. 6 5 Occupational Health and Safety during Construction .............................................................. 7 6 Plant Identification System .......................................................... Error! Bookmark not defined. 7 Measuring Units .................................................................................................................... 7 8 Codes & Standards................................................................................................................ 8 9 Definitions .......................................................................................................................... 34 10 Scope of works ................................................................................................................... 34 11 Other Terms & Conditions ................................................................................................... 37 12 Deliverables ........................................................................................................................ 37




1 General

1.1 Project Description

The project involves provision of drawing water from the canal for Phase II at about

75 m away from existing RWPH of Phase I . Adequate size sluice gate shall be

installed at the location and link channel/canal of adequate size shall be constructed

up to the location of proposed RWPH of Phase II. Similar provision for dual pumping

shall be installed for pumping water either from canal of RWR to WTP inlet and

pumping water to RWR.

RWR of capacity 5310 ML shall be constructed besides existing RWR of Phase I with

provision of interconnection of both RWR to facilitate drawal of water from either

RWR to any of the RWPH. FSL of both the RWR shall be kept same. Single pipeline of

1900 mm MS with internal CML and external 3 LP tape coating shall be provided for

pumping and drawal of water between RWPH and RWR.

Fully automatic Water Treatment Plant of latest technology shall be constructed in

modular design to facilitate future extension to 300 MLD.

In brief the project work involves one stretch of Link Canal, one Raw Water Pumping

Station, one Raw Water Reservoir, one Water Treatment Plant, one CWR, one Clear

Water Pumping Stations, all interconnecting piping and one stretch of Transmission

line with their functions as described above. These major components and the

Transmission Pipe Lines are listed as under:

(a) Raw Water Pumping Station including branch canal from the Link Canal and

intake works for the pumping station.

(b) Raw Water Reservoir Of Capacity 5310 ML.

(c) Water Treatment Plant Capacity : 250 MLD + (Provisions of 50 MLD for future)

(d) Clear Water Reservoir Capacity : 27.5 ML

(e) Clear Water Pumping Station at Nokha Daiya

(f) Transmission line from Nokha Daiya PS upto upstream of CWR at Deshnok PS –

52.25 km long MS 1900 mm dia

2 Site Data

2.1 Project Site Location

Clear Water Reservoir of 27.50 ML effective storage capacity and Elevated WaterReservoir with a

capacity of 1000 cums shall be constructed at Nokha Daiya HeadWorks, whereas the location of

One-way RCC Surge Tank shall be as per surge analyses result/report as approved by EIC. The Nokha

Daiya site is near existing CWR and pump house in the same campus.




2.2 Site Topography

The project site is barren land with some green field places. Intake site is located just beside the

existing canal and WTP site is located besides existing pump station. Soil is majorly sandy type of soil.

2.3 Site Office, Construction & Laydown Area

All the Temporary facilitates required for execution of scope of works shall be considered by the

sub-contractor, and shall be mentioned separately.




3 Climatic Data

3.1 General

The climate of Bikaner is dry. In summer it is extreme hot with temp 41 ͦ to 49 ͦC.The peak maximum recorded temp is 48.9˚C. The summer season is from April to June followed by monsoon season is received. Prevailing wind direction are from south west to North West during summery month & from north east to south west during winter months. The climate being extra dry evaporation is very highs. The annual evaporation is 3048 mm. The rainfall is generally scanty. Average rainfall is 350 mm 80% of rainfall is received from south west during monsoon season. Average numbers of rainy days are 20 days during rainy season.

3.2 Basic Design Data

The plant shall be designed, constructed and installed taking into account of site ambient and local conditions. The Contractor shall give due allowance to the design of plant process tanks and filters for the ambient temperature and direct sunlight to be encountered.

4 Environmental Protection Requirements

General The contractor shall take all the precautions for safeguarding the environment during the course of the construction of the works. He shall abide by all laws, rules and regulations in force governing pollution & environmental protection that are applicable in an area where the works are situated.

A. Air Pollut ion Control

The Contractor shall take all reasonable steps to minimize dust nuisance during the

construction of the works. All existing highways and roads used by vehicle of the

Contractor or any of his sub-contractors or suppliers of materials or plant, and similarly any

new roads which are part of the works and which are being used by traffic, shall be kept

clean and clear of all dust/mud or other extraneous materials dropped by the said vehicles

or their tyres. Similarly, the Contractor shall immediately clear all dust/mud or other

extraneous materials from the works spreading on these highways.

B. Cont rol of Soil Erosion, Sedimentat ion & Water Pollut ion The contractor shall carry out the works in such a manner that soil erosion is fully controlled

and sedimentation & pollution of natural water courses, ponds, tanks & reservoirs are

avoided. The stipulations in clause 306 of MORTH specifications shall govern.

C. Pollut ion f rom Hot –M ix Plants & Batching Plants Bituminous hot-mix plants and concrete batching plants shall be located sufficiently away

from habitation, agricultural operations or industrial establishments. The Contractor will take

every precaution to reduce the levels of noise, vibration, dust and emissions from his plant

and will be responsible for any claims for damages caused to the owners of property, fields

and residences in the vicinity.




D. Burrow Pits for Embankment Const ruct ion

Burrow pits must be selected considering the position of pipe to be laid and the likely excess

earth left after laying of pipe line. If pipe is laid below ground the maximum possible earth

must be excavated from the trench section of pipe. Borrow pits shall not be dug in the right-

of-way of the road. The stipulations in Clause 305.2.2 of MORTH shall govern. After

excavations, the borrow pits sides must be so dressed to form stable slopes. Excavated trench

must be linked with proper grade to ensure that they don’t cause impounding and therunoff

is easily passed in the nearby drain.

E. Quarry Operat ions The Contractor shall obtain materials from quarries only after the consent of the forest

department or other concerned authorities is obtained. The quarry operations shall be

undertaken within the purview of rules & regulations in force.

F. Substances hazardous t o Healt h The Contractor shall not use or generate any materials in the works, which are hazardous to

the health of persons, animals or vegetation. Where it is necessary to use some substances,

which can cause injury to the health of workers, the Contractor shall provide protective

clothing or appliances to his workers

G. Use of Nuclear Guages Nuclear gauges shall be used only where permitted by the Engineer-in-Charge.The

Contractor shall provide the Engineer-in-Charge with a copy of the regulations governing the

safe use of nuclear gauges he intends to employ and shall abide by such regulations.

5 Occupational Health and Safety during Construction

The Contractor shall provide details of their existing Occupational Health and Safety management system and evidence of their OHS track record on similar projects.

The contractor shall provide Environmental, Health & Safety manual for approval.

The Contractor shall ensure that safety processes are put in place to promote a safe environment and structural elements of the project shall be designed, constructed and operated to meet good international industry practice.

6 Measuring Units

The international SI-system of measures and weights shall exclusively be used for documents, correspondence, drawings, instrument scales, on workstation, printouts, etc.




7 Codes & Standards

All designs shall be based on the latest Indian Standard (I.S.) Specifications or Codes of

Practice unless otherwise specified. The design standards adopted shall follow the best

modern engineering practice in the field based on any other International Standard or

Specialist Literature subject to such standard reference or extract of such literature in the

English language being supplied to and approved by the Engineer-in-charge. In case of any

variation or contradiction between the provisions of the I.S. Standards or Codes and the

specifications given along with the submitted tender document, the provision given in this

specification shall be followed. Given below are list of some main codes

IS No. Title Construction Planning and Storage of Materials

4082 : Recommendation on stacking and storage of construction materials at site (first revision)

7969 : Safety code for handling and storage of building materials EARTHWORK

883 : Design of structural timber in building - Code of practice (third revision)

1498 Classification and identification of soils for general engineering purposes (first revision) (Amendments 2)

2682 : 1984 Chlordane emulsifiable concentrates (second revision) (Amendment 1) (Reaffirmed 1994)

3764: 1992 Excavation work - Code of safety (first revision) 4081 Safety code for blasting and related dri lling operations 6313 (Part 2) Code of practice for anti-termite measures in buildings: Part 2 Pre-

constructional chemical treatment measures (Reaffirmed) FOUNDATIONS

269 : 33 grade ordinary Portland cement. 432 (Part 1) Mild steel and medium tensile steel bars and hard-drawn steel

wire for concrete reinforcement: Part 1 Mild steel and medium tensile steel bars (third revision)

455 Portland slag cement 456 Code of practice for plain and reinforced concrete (Reaffirmed 2000) 1080 : 1986 Code of practice for design and construction of shallow

foundations on soils (other than raft, ring and shell) 1489 (Part 1) Portland pozzolana cement: Part 1 Fly ash based 1489 (Part 2) Portland pozzolana cement: Part 2 Calcined clay based 1786 High strength deformed steel bars and wires for concrete

reinforcement 1904 Code of practice for design and construction of

foundations in soils: General requirements 2062 Steel for general structural purposes




2950 (Part 1) Code of practice for design and construction of raft foundations: Part 1 Design

2974 (Part 1) Code of practice for design and construction of machine foundations: Part 1 Foundations for reciprocating type

2974 (Part 2) Code of practice for design and construction of machine foundations: Part 2 Foundations for impact type

2974 (Part 3) Design and construction of machine foundations - Code of practice: Part 3 Foundations for rotary type machines

2974 (Part 4) Code of practice for design and construction of machine foundations: Part 4 Foundations for rotary type machines

2974 (Part 5) Code of practice for design and construction of machine foundations: Part 5 Foundation for impact machines

3629 Specification for structural timber in building (first revision) (Reaffirmed 1991)

4091 : 1979 Code of practice for design and construction of foundations for transmission line towers and poles (first

6403 Code of practice for determination of bearing capacity of shallow foundations.

6909 Specification for super-sulphated cement

8009 (Part 1) Code of practice for calculation of settlement of foundations: Part 1 Shallow foundations subject to

8009 (Part 2) Code of practice for calculation of settlement of foundations: Part 2 Deep foundations subjected to

4138 Safety code for working in compressed air.

8041 Rapid hardening Portland cement

9456: 1980 Code of practice for design and construction of conical and hyperbolic paraboloidal types of shell foundations.

19556 Code of practice for design and construction of diaphragm walls.

11089 Code of practice for design and construction of ring foundation

12269 53 grade ordinary Portland cement.

13094 Guidelines for selection of ground improvement techniques for foundation in weak soils.

13301 Guidelines for vibration isolation for machine foundations

SP 36 (Part 2) :1988

Compendium of Indian Standards on soil engineering : Part 2 Field testing

MASONRY Part 1 Mortars 269 33 grade ordinary Portland cement




383 Coarse and fine aggregates from natural sources for concrete

455 Portland slag cement

456 Code of practice for plain and reinforced concrete

1344 Calcined clay pozzolana

1489 (Part 1) Portland pozzolana cement: Part 1 Fly ash based

1489 (Part 2) Portland pozzolana cement: Part 2 Calcined clay based

2116 Stand for masonry mortars

2250 Code of practice for preparation and use of masonry mortars

2720 (Parts 1 to 41)

Methods of test for soils

3812 Fly ash for use as pozzolana and admixture

6452 Specification for high alumina cement for structural use

6909 Specification for supersulphated cement


8043 Hydrophobic Portland cement

8112 43 grade ordinary Portland cement


12600 Low heat Portland cement

SP 20 (S &T) : Handbook on masonry design and construction

SP 21 (S &T) Summaries of Indian Standards for building materials

Part 2 Brickwork










2645 Integral cement waterproofing compounds


5454 Methods of sampling of clay building bricks


4014 Part 1 & 2 Code of practice for steel tubular scaffolding



8042 White Portland cement



9103 Admixture for concrete



SP 20 (S &T) Handbook on masonry design and construction

SP 21 (S &T) Summaries of Indian Standards for building materials

1077 Common burnt clay building bricks

2212 Code of practice for brick work

3696 (Part 1) Safety code of scaffolds and ladders: Part 1 Scaffolds

4014 (Part 2) Code of practice for steel tabular scaffolding: Part 2 Safety regulations for scaffolding

SP 25 (S & T) Handbook on caused and prevention of cracks in building

Part 3 Stonework




1123 Method of identification of natural building stones

1127 Recommendations for dimensions and workmanship of natural building stones for masonry work

1128 Limestone (slab and tiles)

1129 Recommendation for dressing of natural building stones

1130 Marble (blocks, slabs and tiles)

1597 (Part 1) Code of practice for construction of stone masonry: Part 1 Rubble stone masonry

1597 (Part 2) Code of practice for construction of stone masonry: Part 2 Ashlar masonry

1905 Code of practice for structural use of un-reinforced masonry

2250 Code of practice for preparation and use of masonry mortars

3316 Specification for structural granite

3622 Specification for sandstone (slab and tiles)

3696 (Part 1) Safety code of scaffolds and ladders: Part 1 Scaffolds

4101 (Part 1) Code of practice for external facing and veneers: Part 1 Stone facing

12440 Pre-cast concrete stone masonry blocks

SP 20 (S & T) Handbook on masonry design and construction

SP 21 (S & T) Summary of Indian Standards for building materials

Plain and Reinforced Concrete 269 33 grade ordinary Portland cement

383 Coarse and fine aggregates from natural resources for concrete

432 (Part 1 & 2)

Mild steel and medium tensile steel bars and hard drawn steel wire for concrete reinforcement: Part 1 Mild steel



516 Method of test for strength of concrete

712 Building limes




875 (Part 1) Code of practice for design loads (other than earthquake) for buildings and structures: Part 1 Dead loads -Unit

875 (Part 2) Code of practice for design loads (other than earthquake) for buildings and structures: Part 2 Imposed loads

875 (Part 3) Code of practice for design loads (other than earthquake) for buildings and structures: Part 3 Wind loads

875 (Part 4) Code of practice for design loads (other than earthquake) for buildings and structures: Part 4 Snow loads

875 (Part 5) Code of practice for design loads (other than earthquake) for buildings and structures: Part 5 Special loads and

650 Standard sand for testing of cement

3085 Method of test for permeability of cement mortar & concrete

9284 Method of test for abrasion resistance of concrete

5816 Method of test for splitting tensile strength of concrete cylinders

8142 Method of test for determining setting time of concrete by penetration resistance

12600 Low heat Portland cement masonry cement

3466 Masonry cement

3558 Code of practice immersion Vibrator for consolidating concrete


13620 Fusion bonded epoxy coated reinforcing bars

1343 Code of practice for Pre-stressed concrete

883 Design of structural timber in building - Code of practice

1199 Methods of sampling and analysis of concrete




1566 Hard-drawn steel wire fabric for concrete reinforcement

1786 High strength deformed steel bars and wires for concrete reinforcement




1791 Batch type concrete mixers

1946 Code of practice for use of fixing devices in walls, ceilings and floors of solid construction

2062 Steel and general structural purposes

2386 (Part 1) Methods of test for aggregates for concrete: Part 1 Particle size and shape

2386 (Part 2) Methods of test for aggregates for concrete: Part 2 Estimation of deleterious materials and organic

2386 (Part 3) Methods of test for aggregates for concrete: Part 3 Specific gravity, density, voids, absorption and bulking

2386 (Part 4) Methods of test for aggregates for concrete: Part 4 Mechanical properties

2386 (Part 5) Methods of test for aggregates for concrete: Part 5 Soundness

2386 (Part 6) Methods of test for aggregates for concrete: Part 6 Measuring mortar making properties of fine aggregates

2386 (Part 7) Methods of test for aggregates for concrete: Part 7 Alkali aggregate reactivity

2386 (Part 8) Methods of test for aggregates for concrete: Part 8 Petrographic examination

2502 Code of practice for bending and fixing of bars for concrete reinforcement

2505 Concrete vibrators - Immersion type - General requirements

2506 General requirements for screed board concrete vibrators

2514 Concrete vibrating tables

2751 Recommended practice for welding of mild steel plain and deformed bars for reinforced construction

3025 Methods of sampling and test (physical and chemical) for water used in industry

3036 Laying lime concrete for a waterproofed roof finish - Code of practice


4031 (Part 1) Methods of physical tests for hydraulic cement: Part 1 Determination of fineness by dry sieving

4098 Lime-pozzolana mixture (first revision)

4656 Form vibrators for concrete

4925 Concrete batching and mixing plant




4926 Ready mixed concrete

4990 Plywood for concrete shuttering work



7861 (Part 1) Code of practice for extreme weather concreting: Part 1 Recommended practice for hot weather concreting

7861 (Part 2) Code of practice for extreme weather concreting: Part 2 Recommended practice for cold weather concreting




9012 Recommended practice for Concreting

9013 Method of making, curing and determining compressive strength of accelerated cured concrete test specimens

9103 Admixtures for concrete

10262 Recommended guidelines for concrete mix design

12269 53 Grade ordinary Portland Cement

13330 Sulphate resisting Portland Cement


13311 (Part 1) Non-destructive testing of concrete - Methods of test: Part 1 Ultrasonic pulse velocity

13311 (Part 2) Non-destructive testing of concrete - Methods of test: Part 2 Rebound hammer

SP 23 (S & T) Handbook on concrete mixes (based on Indian Standards)

SP 24 (S & T) Explanatory handbook on Indian Standard Code for plain and reinforced concrete

SP 33 (S & T) Handbook on timber engineering

SP 34 (S & T) Handbook on concrete reinforcement and detailing

Anti-Termite Measures




6313 (Part 1) Code of practice for anti-termite measures in buildings: Part 1 Constructional measures

6313 (Part 2) Code of practice for anti-termite measures in buildings: Part 2 Pre-constructional chemical treatment measures

Door and Windows (Wood And Metal)

208 Door handles

303 Plywood for general purposes

399 Classification of commercial timbers and their zonal distribution

401 Code of practice for preservation of timber

419 Putty, for use on window frames

1003 (Part 1) Timber panelled and glazed shutters: Part 1 Door shutters

1003 (Part 2) Timber panelled and glazed shutters: Part 2 Window and ventilator shutters

1038 Steel doors, windows and ventilators

1081 Code of practice for fixing and glazing of metal (steel and aluminium) doors, windows and ventilators

1328 Veneered decorative plywood

1658 Fibre hardboards

1659 Block boards

2191 (Part 1) Wooden flush door shutters (cellular and hollow core type): Part 1 Plywood face panels

2191 (Part 2) Wooden flush door shutters (cellular and hollow core type): Part 2 Particle board and hard board face panels

2202 (Part 1) Wooden flush door shutters (solid core type): Part 1 Plywood face panels

2202 (Part 2) Wooden flush door shutters (solid core type): Part 2 Particle board and hard board face panels

2553 (Part 1) Safety glass: Part 1 General purpose

2835 Flat transparent sheet glass

3087 Wood particle boards (medium density) for general purposes

3097 Veneered particle boards




3129 Low density particle boards

3348 Specification for Fibre insulation boards

3478 Specification for high density wood particle boards

3548 Code of practice for glazing in building

10521 Collapsible gates

6248 Metal rolling shutters & grills

10451 Steel sliding shutters

1361 Steel windows for industrial buildings, ventilation blinds for windows

4021 Timber door, window and ventilator frames

1826 Venation blinds for windows

1948 Aluminium doors, windows and ventilators

4020 (Parts 1-16)

Door shutters, method of test

4351 Specification for steel door frames

4913 Code of practice for selection, installation and maintenance of timber doors and windows

4962 Specification for wooden side sliding doors

5187 Flush bolts

5437 Figured, rolled and wired glass

5509 Fire retardant plywood

5539 Specification for preservative treated plywood

6198 Legged, braced and battened timber door shutters

6248 Specification for metal rolling shutters and rolling grills

6534 Guiding principles of grading and inspection of timber

6701 Tungsten filament miscellaneous electric lamps




7316 Decorative plywood using plurality of veneers for decorative faces

7452 Hot-rolled steel sections for doors, windows and ventilators

10439 Code of practice for patent glazing

10451 Steel sliding shutters

10521 Collapsible gates

10701 Structural plywood

11433 (Part 1) One part grade polysulphide base joints sealant: Part 1 General requirements

11433 (Part 2) One part grade polysulphide base joints sealant: Part 2 Methods of test

12896 Classification of Indian timbers for door and window shutters and frames

SP 21 (S & T) Summarise of Indian Standards for building materials

SP 33 (S & T) Handbook on timber engineering

Floors and Floor Coverings

77 Linseed oil, boiled for paints





455 Portland stag cement


533 Gum spirit of turpentine (oil of turpentine)

651 Salt glazed stoneware pipes and fittings

653 Linoleum sheets and tiles

657 Materials for use in the manufacture of magnesium oxy-chloride flooring compositions




658 Code of practice for magnesium-oxychloride composition floors

712 Building limes

723 Steel countersunk head wire nails

809 Rubber flooring materials for general purposes


1195 Bitumen mastic for flooring

1196 Code of practice for laying bitumen mastic flooring

1197 Code of practice for laying of rubber floors

1198 Code of practice for laying, fixing and maintenance of linoleum floor

1237 Cement concrete flooring tiles

1322 Bitumen felts for waterproofing and damp-proofing

1443 Code of practice for laying and finishing of cement concrete flooring tiles



1580 Bituminous compounds for water proofing and caulking purposes

1609 Code of practice for laying damp-proofing treatment using bitumen felts

1661 Code of practice for application of cement and cement-lime plaster finishes

2114 Code of practice for laying in-situ terrazzo floor finish

2116 Sand for masonry mortars

2180 Heavy duty burnt clay building bricks

2386 (Part 4) Methods of test for aggregates for concrete: Part 4 Mechanical properties

2571 Code of practice for laying in-situ cement concrete flooring

3384 Specification for bitumen primer for use in waterproofing and damp proofing




3414 Code of practice for design and installation of joints in buildings

3461 Specification for PVC - asbestos floor tiles

3462 Specification for unbacked flexible PVC flooring

3502 Steel Chequered plates

3583 Specification of burnt clay paving bricks

3622 Specification for sandstone (slabs and tiles)

3629 Specification for structural timber in building

3670 Code of practice for construction of timber floors

4441 Code of practice for use of silicate type chemical resistant mortars

4442 Code of practice for use of sulphur type chemical resistant mortars

4443 Code of practice for use of resin type chemical resistant mortars

4456 (Part 1) Methods of test for chemical resistant mortars - Part 1 Silicate type and resin type

4456 (Part 2) Methods of test for chemical resistant mortars - Part 2 Sulphur type

4457 Ceramic unglazed vitreous acid resisting tile

4631 Code of practice for laying of epoxy resin floor toppings

4832 (Part 1) Specification for chemical resistant mortars: Part 1 Silicate type

4832 (Part 2) Specification for chemical resistant mortars: Part 2 Resin type

4832 (Part 3) Specification for chemical resistant mortars: Part 3 Sulphur type

4860 Acid resistant bricks

4971 Recommendations for selection of industrial floor finishes

5318 Code of practice for laying of flexible PVC sheet and tile flooring

5389 Code of practice for laying of hardwood parquet and wood block floors

5491 Code of practice for laying of in-situ granolithic concrete flooring topping




5760 Compressed argon

5766 Code of practice for laying of burnt clays brick flooring


7193 Glass fibre base coaltar pitch and bitumen felts


8374 Bitumen mastic, anti-static and electrically conducting grade

9077 Code of practice for corrosion protection of steel reinforcement in RB and RCC construction

9197 Epoxy resin, hardness and epoxy resin compositions for floor toppings

9472 Code of practice for laying mosaic parquet flooring

10440 Code of practice for construction of RB and RBC floors and roofs

Wall and Ceiling Finishes and Coverings and Walling




451 Technical supply conditions for wood screws


459 Corrugated and semi-corrugated asbestos cement sheets

710 Marine plywood

712 Building limes


733 Wrought aluminium and aluminium alloy bars, rods and sections for general engineering purposes

737 Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes

777 Glazed earthenware wall tiles




883 Design of structural timber in building - Code of Practice

1130 Marble (blocks, slabs and tiles)

1237 Cement concrete flooring tiles

1328 Veneered decorative plywood


1414 Code of practice for fixing wall covering



1542 Sand of plaster

1635 Code of practice for field slaking of building lime and preparation of putty

1658 Fibre hardboards

1659 Block boards

1661 Code of practice for application of cement and cement-lime plaster finishes

1946 Code of practice for use of fixing devices in walls, ceilings and floors of solid construction

2095 Gypsum plaster boards

2098 Asbestos cement building boards

2114 Code of practice for laying in-situ terrazzo floor finish

2116 Sand for masonry mortar

2185 (Part 1) Concrete masonry units : Part 1 Hollow and solid concrete blocks

2185 (Part 2) Concrete masonry units : Part 2 Hollow and solid light weight concrete blocks

2185 (Part 3) Concrete masonry units : Part 3 Autoclaved cellular aerated concrete blocks

2402 Code of practice for external rendered finishes

2441 Code of practice for fixing ceiling covering




2547 (Part 1) Gypsum building plaster : Part 1 Excluding premixed lightweight plaster

2547 (Part 2) Gypsum building plaster : Part 2 Premixed lightweight plaster

2691 Burnt clay facing bricks

2818 Indian hessian : Part 1 General

2849 Specification for non-load bearing gypsum partition blocks

3087 Wood particle boards (medium density) for general purposes

3097 Veneered particle boards

3129 Low density particle boards

3348 Specification for fibre insulation boards

3466 Specification for masonry cement

3478 Specification for high density wood particle boards


3630 Code of practice for construction of non-load bearing gypsum block partitions

3677 Unbonded rock and slag wool for thermal insulation


4101 (Part 1) Code of practice for external facing and veneers: Part 1 Stone facing

4101 (Part 2) Code of practice for external facing and veneers: Part 2 Cement Concrete facing

4101 (Part 3) Code of practice for external facing and veneers: Part 3 Wall tiling and mosaics

4407 Code of practice for reed walling

4671 Expanded polystyrene for thermal insulation purposes

5390 Code of practice for construction of timber ceiling

5509 Fire retardant plywood

6730 Felt nails




6738 Panel pins and lost head nails

6760 Slotted countersunk head wood screws

7316 Decorative plywood using plurality of veneers for decorative faces


12727 Code of practice for no fines cast in-situ cement concrete

Roofs and Roofing

158 Ready mixed paint, brushing, bituminous, black Lead (Pb)-free, acid alkali and heat resisting

217 Cutback bitumen


277 Galvanized steel sheet (plain and corrugated)

280 Mild Steel wire for general engineering


432 (Part 1) Mild steel and medium tensile steel bars and hard-drawn steel wire for concrete reinforcement: Part 1 Mild steel

451 Technical supply conditions for wood screws

455 Portland stag cement


459 Corrugated and semi-corrugated asbestos cement sheets


725 Copper wire nails

730 Hook bolts for corrugated sheet roofing

805 Code of practice for use of steel in gravity water tanks

808 Dimensions for hot-rolled steel beam, column channel and angle sections

883 Design of structural timber in building - Code of Practice





1120 Coach screws

1199 Methods of sampling and analysis of concrete

1254 Corrugated aluminium sheet


1343 Code of practice for Pre-stressed concrete




2098 Asbestos cement building boards

2119 Code of practice for construction of brick-cum-concrete composite (Madras terrace) floor or roof

2204 Code of practice for construction of reinforced concrete shell roof

2527 Code of practice for fixing rainwater gutters and down pipes for roof drainage

2690 (Part 1) Burnt clay flat terracing tiles: Part 1 Machine made

2690 (Part 2) Burnt clay flat terracing tiles: Part 2 Hand made

3007 (Part 1) Code of practice for laying of asbestos cement sheets: Part 1 Corrugated sheets

3007 (Part 2) Code of practice for laying of asbestos cement sheets: Part 2 Semi-corrugated sheets


6061 (Part 1) Code of practice for construction of floor and roof with joints and filler blocks : Part 1 with hollow concrete

6061 (Part 2) Code of practice for construction of floor and roof with joints and filler blocks : Part 2 with hollow clay filler

6061 (Part 3) Code of practice for construction of floor and roof with joints and filler blocks : Part 3 Precast hollow clay

6061 (Part 4) Code of practice for construction of floor and roof with joints and filler blocks : Part 4 With precast hollow clay

6332 Code of practice for construction of floor and roofs using precast doubly curved shell units




8869 Washers for corrugated sheet roofing

12093 Code of practice for laying and fixing of sloped roof coverings using plain and corrugated galvanized steel

12506 Code of practice for improved thatching of roof with rot and fire retardant treatment

Damp - Proofing and Waterproofing

73 Paving bitumen



702 Industrial bitumen

1195 Bitumen mastic for flooring

1203 Determination of penetration


1346 Code of practice for waterproofing of roofs with bitumen felts

1580 Bituminous compounds for water proofing and caulking purposes

1609 Code of practice for laying damp-proofing treatment using bitumen felts

1635 Code of practice for field slaking of building lime and preparation of putty

1834 Hot applied sealing compound for joint in concrete

2116 Sand for masonry mortars

2508 Low density polyethylene films

2527 Code of practice for fixing rainwater gutters and down pipes for roof drainage

2541 Code of practice for preparation and use of lime concrete

2645 Integral cement water proofing compounds

2690 (Part 1) Burnt clay flat terracing tiles: Part 1 Machine made

2690 (Part 2) Burnt clay flat terracing tiles: Part 2 Hand made




3036:1992 Laying lime concrete for a waterproofed roof finish

3037 Bitumen mastic for use in waterproofing of roofs

3067 Code of practice for general design details and preparatory work for damp-proofing and waterproofing

3370 (Part 1 to IV )

Code of practice for concrete structures for the storage of liquids:


4098 Lime-pozzolana mixture

4365 Code of practice for application of bitumen mastic for water proofing of roofs

5871 Bitumen mastic for tanking and damp-proofing

6494 Code of practice for waterproofing of underground water reservoirs and swimming pools

7193 Glass fibre base coaltar pitch and bitumen felts

7198 Code of practice for damp-proofing using bitumen mastic

7290 Recommendations for use of polyethylene film for waterproofing of roofs

9759 Guidelines for dewatering during construction

9918 Code of practice for application of silicone based water repellent

12027 Silicone-based water repellents

12054 Code of practice for application of silicone based water repellent

13182 Waterproofing and damp-proofing of wet areas in building Recommendations

Joints in Buildings (Control of Cracks In Buildings)

1834 Hot applied sealing compound for joint in concrete

1838 (Part 1) Performed fillers for expansion joint in concrete pavements and structures (non extruding and resilient

1838 (Part 2) Performed fillers for expansion joint in concrete pavements and structures (non extruding and resilient

3414 Code of practice for design and installation of joints in buildings

10958 General check list of functions of joints in buildings




11433 (Part 1) One part grade polysulphide based joint sealant: Part 1 General Requirements

11817 Classification of joints in buildings for accommodation of dimensional deviations during construction

11818 Method of test for laboratory determination of air permeability of joints in buildings

12118 (Part 1) Two parts polysulphide based sealant: Part 1 General requirements

White Washing, Colour Washing and Painting of Masonry, Concrete and Plaster Surfaces (Calcareous

44 Iron oxide pigments for paints

55 Ultramarine blue for paints

109 Ready mixed paint, brushing, priming, plaster, to Indian Standard Colour No. 361 and 631 White and off white

133 Enamel, interior: (a) undercoating, (b) finishing

158 Ready mixed paint, brushing, bituminous, black lead-free, acid alkali and heat resisting

168 Ready mixed paint, air drying, for general purpose

427 Distemper, dry, colour as required

428 Distemper, oil emulsion, colour as required

702 Industrial bitumen

712 Building limes

2395 (Part 1) Code of practice for painting concrete masonry and plaster surfaces : Part 1 Operation and workmanship

2395 (Part 2) Code of practice for painting concrete masonry and plaster surfaces : Part 2 Schedule

2547 (Part 1) Gypsum building plaster: Part 1 Excluding premixed lightweight plaster

2547 (Part 2) Gypsum building plaster: Part 2 Premixed lightweight plaster

2932 Enamel, synthetic, exterior (a) undertaking (b) finishing

2933 Enamel, exterior (a) undertaking (b) finishing

3140 Code of practice for painting asbestos cement building products





5410 Cement paint

5411 (Part 1) Plastic emulsion paint: Part 1 for interior use

5411(Part 2) Plastic emulsion paint: Part 2 for exterior use

6278 Code of practice for whitewashing and colour washing

9862 Ready mixed paint, brushing, bituminous, black lead-free, acid alkali, water and chlorine resisting

Painting, Varnishing and Allied Finishes (Wood And Metals)

102 Ready mixed paint, brushing, red lead, non settling, painting

110 Ready mixed paint, brushing, Grey filler, for enamels for use over primers

117 Ready mixed paint, brushing, finishing exterior, semi-gloss for general purposes to Indian Standard Colours

124 (Part 3) Ready mixed paint, brushing, finishing exterior, semi-gloss for general purposes: Part 3 (superseding IS 119)

127 Ready mixed paint, brushing, finishing exterior, semi-gloss for general purposes white

128 Ready mixed paint, brushing, finishing exterior, semi-gloss for general purposes black

133 Enamel, interior: (a) undercoating, (b) finishing

137 Ready mixed paint, brushing, matt or eggshell flat, finishing, interior to Indian Standard colour as required

144 Ready mixed paint, brushing, petrol resisting, air-drying, for interior painting of tanks and container, red oxide

158 Ready mixed paint, brushing, bituminous, black lead-free, acid alkali and heat resisting

198 Varnish gold size

207 Gate and shutter hooks and eyes

337 Varnish, finishing interior

348 French polish


423 Plastic wood for joiners filter

524 Varnish, finishing, exterior, synthetic, air drying




525 Varnish, finishing, exterior and general purposes

1477 (Part 1) Code of practice for painting of ferrous metals in buildings: Part 1 Pre-treatment

1477 (Part 2) Code of practice for painting of ferrous metals in buildings: Part 2 Painting

2338 (Part 1) Code of practice for finishing of wood and wood based materials: Part 1 Operations and workmanship

2338 (Part 2) Code of practice for finishing of wood and wood based materials: Part 2 Schedules

2339 Aluminium paint for general purposes, in dual container

2554 (Part 1&2) Code of practice for painting of non ferrous metals in buildings

2524 (Part 1) Code of Practice for painting of non-ferrous metals in buildings; Part

2524 (Part 1) Code of Practice for painting of non-ferrous metals in buildings; Part

2932 Enamel, synthetic, exterior (a) undertaking (b) finishing

2933 Enamel, exterior (a) undertaking (b) finishing

3531 Glossary of terms relating to corrosion of metals

3536 Ready mixed paint, brushing, wood primer, pink

3537 Ready mixed paint, finishing interior, for general purposes, to Indian Standard Colours No. 101, 216, 217,

3539 Ready mixed paint, undercoating for use under oil finishes to Indian Standard Colours, as required

3585 Ready mixed paint, aluminium, brushing priming water resistant, for woodwork

4597 Code of Practice for finishing of wood and wood based products with nitrocellulose and cold catalysed materials

6005 Code of practice for phosphating of iron and steel

Water Supply And Drainage

Part 1 Water Supply

1172 Code of basic requirements of water supply, drainage and sanitation

1239 (Part 1) Mild steel tubes, tubular and other wrought steel fittings: Part 1 Mild steel tubes

1536 Centrifugally cast (spun) iron pressure pipes for water, gas and sewage




1537 Vertically cast iron pressure pipes for water, gas and sewage

1592 Asbestos cement pressure pipes

3114 Code of practice for laying of cast iron pipes

5822 Code of practice for welded steel pipes for water supply

1626 (Part 1) Asbestos cement building pipes and pipe fittings, gutters and gutter fittings and roofing fittings: Part 1 (Pipe and

2064 Selection, installation and maintenance of sanitary appliances - Code of practice

2065 Code of practice for water supply in buildings

2692 Ferrules for water services

3076 Low density polyethylene pipes of potable water supplies; sewage and industrial effluents

4984 Specification for high density polyethylene pipes for potable water supplies; sewage and industrial effluents

4985 Specification for un-plasticised PVC pipes for potable water supplied

7558 Code of practice for domestic hot water installations

7634 (Part 2) Code of practice for plastics pipe work for potable water supplies : Part 2 Laying and jointing polyethylene (PE)

7634 (Part 3) Code of practice for plastics pipe work for potable water supplies : Part 3 Laying and jointing of UPVC pipes

12183 (Part 1) Code of practice for plumbing in multi-storeyed buildings: Part 1 Water supply

1916 Steel cylinder pipes with lining and coating

4127 Code of practice for laying of salt glazed stoneware pipes

12709 Glass fibre reinforced plastic pipes, joints and rings for potable water supply

3597 Concrete pipes-methods of test

7319 Perforated concrete pipes

NBC National Building Code of India

SP 35 (S & T) Handbook of water supply and drainage with special emphasis on plumbing

Part 2 Building Drainage




277 Galvanized steel sheet (plain and corrugated)

458 Precast concrete pipes (with and without reinforcement)

651 Salt glazed stoneware pipes and fittings

782 Caulking lead

783 Code of Practice for laying of concrete pipes

1230 Cast iron rainwater pipes and fittings

1536 Centrifugally cast (spun) iron pressure pipes for water, gas and sewage

1537 Vertically cast iron pressure pipes for water, gas and sewage

1592 Asbestos cement pressure pipes

1626 (Part 1) Asbestos cement building pipes and pipe fittings, gutters and gutter fittings and roofing fittings: Part 1 (Pipe and

1726 Cast iron manhole covers and frames

1742 Code of Practice for building drainage

3006 Specification for chemically resistant glazed stoneware pipes and fittings

4111 (Parts 1 to 5)

Code of Practice for ancillary structures in sewerage system

4733 Methods of sampling and test for sewage effluents

4984 Specification for high density polyethylene pipes for potable water supplies; sewage and industrial effluents

4985 Specification for unplasticised PVC pipes for potable water supplied

5329 Code of Practice for sanitary pipe work above ground for buildings

5455 Cast iron steps for manholes

12592 (Parts 1 & 2)

Precast manhole covers & frames

4350 Concrete porous pipes for Under drainage

2470 (Parts 1 & 2) Code of Practice for installation of septic tank

784 Pre-stressed concrete pipes

Special Construction Procedures Earthquake Effects, etc.




1893 Criteria for earthquake resistant design of structures

4326 Earthquake resistant design and construction of buildings- Code of practice

13920 Ductile detailing of reinforced concrete structures subjected to seismic forces - Code of practice

13935 Repair and seismic strengthening of buildings - Guidelines

4991 Criteria for blast resistant design of structures for explosions above ground

6922 Criteria for safety and design of structures subject to underground blasts

2190 Selection, installation and maintenance of first-aid fire extinguishers - Code of practice

3696 (Part 2) Safety code of scaffolds and ladders: Part 2 Ladders

4912 Safety requirements for floor and wall openings, railings and toe boards

General

10005 S.I. units and recommendations for use of their multiples and of certain other units

6060 Code of practice for day lighting of factory buildings

3103 Code of practice for industrial ventilation

3483 Code of practice for noise reduction in industrial buildings

2440 Guide for day lighting of buildings

1200 (1 to 28) Method of measurement of Building and Civil Engg. Works

7973 Code of practice for architectural and building working drawings

962 Code of practice for architectural and building drawings

13415 Code of safety for protective barrier in and around buildings

4801 Safety code for blasting and related drilling operations

8969 Safety code for erection of concrete framed structures




8 Definitions

Employer : Public Health Engineering Department, Rajasthan FS/FEED services : STC, NK & AECOM Abeinsa : Main EPC Contractor to whom the Employer has entrusted the design & Construction of the power plant on EPC turnkey basis. Contractor : Specialist agency appointed by Abeinsa to execute the construction works.

9 Scope of works

The services to be provided within the framework of this specification comprise the planning, complete supply and execution in every aspect including all necessary calculations and documentation, prefabrication, delivery, erection and acceptance of all civil works required for faultless operation of the plant in the following fields

9.1 Preliminary works

a) Surveying works; b) Site preparation work including clearance of site, removal/relocating of existing facilities and

obstacles, grading, leveling, grubbing and filling and compacting the complete site to the specified levels.

9.2 Common works

a) Treatment & disposal of excess earth material to areas; b) Dewatering works as required for construction in dry conditions; c) All earth works required;

9.3 Hydraulic structures

a) Link canal of 100m length with 4.0m wide access road along the canal

b) Raw water reservoir of capacity 5310 ML with PCC block tile lining

c) RCC Clear water Reservoir of capacity 27.5 ML with top roof slab.

9.4 Buildings

Following buildings including isolated foundations, pile caps; RCC frame work, structural steel, architectural finishes, plumbing, furniture, appliances, waterproofing etc. are included in the scope of works: a) Substation building b) Local Electrical building c) Chemical house d) Residential Quarters e) Clear water Pump house f) Raw water pump house g) Chlorination Building




h) Administration & Control Building i) SCADA Control Room Building

9.5 Equipment foundations

Foundation for the following equipment with protective coating, pile caps are included in the scope:

a) Pump foundations

b) Pipe racks

c) Flash mixer tank d) Clariflocculator e) Rapid Sand filter f) Sludge drying bed g) Filtrate sump h) Transformer foundations

9.6 Tanks & Pits

Following tanks including protective coating, plastering and painting are included in scope

i. Post Chlorination Tank - 2 nos;

ii. Sludge Balancing Tank - 1 nos;

iii. Elevated Back wash water Tank - 1 nos;

iv. DirtyBack wash water Tank - 1 nos;

v. Septic Tank - 1 nos

vi. One way surge tank

vii. Thickened Sludge storage Tank- 1 nos

viii. Flow meter chamber

ix. Inlet chamber -1 nos

x. Distribution chamber -1 nos

9.7 Outdoor facilities

Following outdoor facilities including all necessary civil works are included in the scope:

a) Car park shades

b) Temporary security fence

c) Walkways, Stairs

d) Gates

e) Gravel surfacing around equipment maintenance laydown areas

f) Stone pitching on embankment

g) RR masonry Boundary wall

9.8 Drainage network

Following drainage network comprising of trenching, pipe laying etc. are included in the scope:

a) Storm water and process drains

b) Domestic sewage drains,




c) Effluent drains;

d) Manholes;

e) Collection pit;

f) Valve chambers;

9.9 Cable Containment

Trench works comprising of excavation, sand bedding, backfilling with selected earth, disposal of

excess material, warning tapes, cable protection tiles etc. for the following are included in the scope:

a) 33 /6.6 KV substation

9.10 Roads

Road access shall be provided to outdoor contract works equipment and campus development areas

Finished surfaces around equipment maintenance laydown areas shall be compacted gravel suitable

for heavy vehicular access & maintenance.

9.11 Land Finishes

Following land finishes are included in the scope:

a) Gravel surfacing around equipment maintenance laydown areas.

b) Compacted ground: the rest of the surface area, mainly areas around tanks, and other non-

specified areas.

9.12 Furniture & Appliance

Furniture as required for proper functioning of offices, control rooms & human resources.

9.13 Green landscaping & Horticulture

Horticulture and Landscaping shall be done according to the topography of the area and should be

planned so as to make the campus a focal point. The open areas must either be covered by tree

plantation or must be suitably grassed. Shadow trees must be planted at a maximum distance of 30

m c/c along the periphery of the campus area and along the roads. The campus must be provided

with gardens, with seasonal flowerbeds and decorative plants.

Horticulture operations shall be started on ground previously levelled and dressed to require

formation levels and slopes. In case where unsuitable soil is met with, it shall be either removed or

replaced or it shall be covered over to a thickness decided by Engineer-in-charge with good earth

materials.

9.14 Rainwater Harvesting

The Contractor shall construct a complete Rain Water Harvesting (RWH) system at each Pumping

station locations Deshnok and Jodhyasi. System will consist of following units:-

a) Desilting / Filter Pit:-

Excavated pit constructed with RCC Chamber and filled with stone/brick/ filter media for

water filtration shall be provided.

b) Collection Tank:-




For storage of rain water a 50000 litres capacity RCC storage tank in M 25 design mix shall

be provided.

c) Recharge Tank:-

To collect the initial rain from roof and overflow rain water from collection tank, a recharge

tank shall be construct. This tank shall be construct in a size of 1.50 X 1.50 X 5.00 mtr with

M25 grade RCC floor, wall and roof covering. Provisions of vent pipes, one opening covered

with manhole cover shall be made. Facilities for by-passing of initial rain water from roof and

overflow from collection tank shall be provided. The Contractor shall also design and provide

required facilities for the use of harvested water.

10 Other Terms & Conditions

The following shall be considered:

a) Validity of the price shall be 150 days;

b) Defect Liability period shall be one year;

c) The unit item rates shall be in Indian Currency (INR)

11 Deliverables

Contractor shall submit the following with the quotation:

a) BOQ duly filled;

b) List of inclusion & exclusion;

c) List of equipment;

d) Manpower histogram;

e) Construction schedule.

f) Method statement for all civil works

*** The End ***

00 RFQ Civil ,RCC & Arch Works Rev

Documents

Transcript of 00 RFQ Civil ,RCC & Arch Works Rev