Transcript of Study on the Bonding Process of Wedges and Ultrasonic Wire ...
<4D6963726F736F667420576F7264202D2033362D31342E20B7A4A7CEBE5ABC4CBB50B657ADB5AA69BE5ABD75B1B5A658B94CB57BA4A7ACE32E646F63>181
Wire Bonding
ABSTRACT
Integrated circuit packaging is a backend process of semiconductor
industry. Due to
the modeling diversification of assembly, process accuracy is
required to higher quality.
Ultrasonic wedge bonding is one of the most important
interconnection techniques for
IC dies inner circuits with the outer world for the power and
signal transportation. There
is a significant effect of the bonding parameters to the joint
quality and reliability.
Therefore, the chemical etching method observes the bond
configuration and interface
characteristics. It is found that the bond interface form the
oval-shaped with the increase
of the ultrasonic power relation, furthermore, the actual joining
position develop from
the bond peripheral to the central, and to the whole bond
interface. The bond area is
increased in the substrate, and the bond strength will be increased
relatively.
182
(Tape automated bondingTAB)(Flip chipFC)
[1]
(Pad)
bondingT/S)
(Ball grid arrayBGA)
(Pull tester)
(60KHz 110KHz)
Li [4] Al-Ni
Cheung[5]
200
(Heel)
183
PCB PCB
60KHz(Wire feed angle) 30 o ()
(Al+Si 1)(WC2130-2025-L)() 99.99
(Cermet2130-2020-L-CC-CG BKCER)()
31.75µm
PCB
184
F ( F1 )
( F2 )(Neck)
(Tail consistency)(BR)
20mw 70mw 5.2gf
0.9 PCB
110mw
PCB
() 110mw
SEM110mw
185
170mw()
5gf 1.8
(~) 110mw
((f))
()
σe < σy
X
X2 X3
σe1 σe2
X2 X1
7.2gf 35ms
95gf 110mw 5.3gf
[1] T.S. Saraswati, T. Sritharan, C.I. Pang, Y.H. Chew, C.D.
Breach, F. Wulff, S.G.
Mhaisalkar, C.C. Wong, “The effects of Ca and Pd dopants on gold
bonding wire
and gold rod,” Thin Solid Films 462–463 (2004) 351–356.
[2] J. Onuki, M. Koizumi, I. Ishikawa, “Effect of Frequency and
Surface Cleanliness
of Al-Si Electrode on Ultrasonic Bonding Characteristics of Thick
Al Wire
Bonding,” Materials Transactions JIM 37 (1996) 1492–1496.
[3] T.Y. Lin, K.L. Davison, W.S. Leong, Simon Chua, Y.F. Yao, J.S.
Pan, J.W. Chai,
K.C. Toh, W.C. Tjiu, “Surface topographical characterization of
silver-plated
film on the wedge bondability of leaded IC packages,”
Microelectronics
Reliability 43 (2003) 803-809.
[4] M.Li, H. Ji, C. Wang, H.S. Bang, H.S. Bang, “Interdiffusion of
Al-Ni system
enhanced by ultrasonic vibration at ambient temperature,”
Ultrasonics 45 (2006)
61–65.
[5] Y.M. Cheung, S.W. Or, and Stephen Ching, “Low temperature gold
wire
bonding,” IEEE/CPMT Electronics Manufacturing Technology Symposium
(1999)
196-202
[6] V. H. Winchell, H. M. Berg, “Enhancing Ultrasonic Bond
Development,” IEEE
Transactions on Components Hybrids Manufacturing Technology
CHMT-1
(1978) 211–218.
[7] H. Ji, M. Li, C. Wang, H. S. Bang, H. S. Bang, “Comparison of
interface
evolution of ultrasonic aluminum and gold wire wedge bonds during
thermal
aging,” Materials Science and Engineering A 447 (2007)
111–118.
Journal of China Institute of Technology Vol.36-2007.6
187
[8] T.R Daniel, N. DeePak, G. David, S. Dongkai, “Evaluation of
wire bonding
performance, process conditions, and metallurgical integrity of
chip on board wire
bonds,” Microelectronics Reliability 45 (2005) 379-390.
[9] Y.H. Tian, I. Lum, S.J. Won, S.H. Park, J.P. Jung, M. Mayer, Y.
Zhou,
“Experimental study of ultrasonic wedge bonding with copper wire,”
IEEE
Electronic Packaging Technology (2005) 389-393.
[10] Y. Ding, J.K. Kim, P. Tong, “Numerical analysis of ultrasonic
wire bonding:
Effects of bonding parameters on contact pressure and frictional
energy,”
Mechanics of Materials 38 (2006) 11–24.
[11] Y. Takahashi, M. Inoue, “Numerical study of wire
bonding-analysis of interfacial
deformation between wire and pad,” Journal of Electronic Packaging
124 (2002)
27–36.
[12] H. Ji, M. Li, C. Wang, J. Guan, H. S. Bang, “Evolution of the
bond interface
during ultrasonic Al-Si wire wedge bonding process,” Journal of
Materials
Processing Technology 182 (2007) 202-206.
[13] Wire Bonding Tools, Gaiser Tool Company manual, Volume
11.
188
300~500
150~250
Bonding time
Ultrasonic power
Bonding force
Bonding time
Ultrasonic power
Bonding force
189
191
Def orm
Journal of China Institute of Technology Vol.36-2007.6
193
80 100
120 140
160 180
P u l l t e s t ( g f )
Defo rmatio
Journal of China Institute of Technology Vol.36-2007.6
195
( 19ms 90gf
(a)70mw (b)90 mw (c)110 mw (d)130 mw (e)150 mw (f)170 mw)
(a) (b)
(c) (d)
(e) (f)
( 35ms 95gf
(a)90mw (b)110 mw (c)130 mw (d)150 mw (e)170 mw (f)200 mw)
(a) (b)