Post on 29-Sep-2015
description
Mohd. Hanif Dewan, Chief Engineer and Maritime Lecturer & Trainer, Bangladesh.
SHIP CONSTRUCTION-
SHIP DIMENSIONS
Definitions and
ShipS DimenSionS Hull: The structural body of a ship including shell plating, framing, decks and bulkheads. Afterbody : That portion of a ships hull abaft midships. Forebody: That portion of a ships hull forward midships. Bow : The forward of the ship Stern : The after end of the ship
8/23/2014 2 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Length Overall
STARBOARD
Beam
PORT
bow midships bridge stern
8/23/2014 3 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
starboard bow
starboard beam
starboard quarter
Dead ahead Dead Stern
Port bow
Port beam
port quarter
8/23/2014 4 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Port : The left side of the ship when looking forward
Starboard : The right side of the ship when looking forward
8/23/2014 5 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Length between perpendicular (LBP) Length on waterline (LWL)
Length overall (LOA)
freeboard
Amidships
Aft perpendicular Fwd perpendicular
Sheer aft Sheer fwd
Summer load line
SHIP DIMENSIONS
Camber Tumble home
Depth
Moulded beam
Rise of floor Half siding of keel
Base line
Draft
8/23/2014 6 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
After Perpendicular (A.P.): A perpendicular drawn to the waterline at the point where the aft side of the rudder post meets the summer load line. Where no rudder post is fitted it is taken as the centre line of the rudder stock.
Forward Perpendicular (F.P.): A perpendicular drawn to the waterline at the point where the foreside of the stem meets the summer load line.
Length Between Perpendicular (L.P.P. / L.B.P.): The length between the forward and the aft perpendiculars measured along the summer load line.
8/23/2014 7 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Amidships: A point midway between the after and forward perpendiculars
Length Overall (L.O.A.): Length of the vessel taken over all extremities.
Base line: A horizontal line drawn at the top of the keel plate. All vertical moulded dimensions are measured relative to this line
Moulded beam: Measured at the midship section is the maximum moulded breadth of the ship
8/23/2014 8 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Moulded Draft/ Draught: The distance from the bottom of the keel to the waterline. The load draft is the maximum draft to which a vessel may be loaded
Moulded Depth: Measured from the base line to the heel of the upper deck beam at the ships side aidships.
Sheer: Curvature of decks in the longitudinal direction. Measured as the height of deck at side at any point above the height of deck at side amidships
8/23/2014 9 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Camber / Round of Beam: Curvature of decks in the transverse direction. Measured as the height of deck above the height of deck at side
Rise of floor / Deadrise: The rise of the bottom shell plating line above the base line. This rise is measured at the line of moulded beam
Half sliding of keel: The horizontal flat portion of the bottom shell measured to port or staoad of the ships logitudial ete line. This is useful dimension to know when dry-docking.
8/23/2014 10 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Tumble home: The inward curvature of the side shell above the summer load line.
Freeboard: the vertical distance measured from the waterline to the top of the deck plating at the side of the deck amidships. Normally exposed to weather and sea.
Flare: The outward curvature of the side shell above the waterline. It promotes dryness and is therefore associated with the fore end of ship
8/23/2014 11 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Extreme Beam:
The maximum beam taken over all extremities.
Extreme Draft:
Taken from the lowest point of keel to the summer load line.
Draft marks represent extreme drafts.
Extreme Depth:
Depth of essel at ships side fo uppe dek to loest poit of keel.
Half Breadth:
Sie a ships hull is syetial aout the logitudial centre line, often only the half beam or half breadth at any
section is given.
8/23/2014 12 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
SCANTLING The dimensions of the structural items of a ship, e.g. frames, girders, plating , etc.
INTERCOSTAL Composed of separate parts, non-continuous
8/23/2014 13 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
CENTER OF FLOATATION
It is the center of the waterplane area and is the
axis about which a ship changes trim.
CENTER OF BUOYANCY
It is the center of the underwater volume of the
ship where the force of buoyancy acts.
CENTER OF GRAVITY
It is the point at which the whole weight of the
object may be regarded as acting. If the object is
suspended from this point, it will remain balanced and
not tilt.
8/23/2014 14
Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
TONNAGE MEASUREMENT
This is often referred to when the size of the vessel is discussed, and the gross toage is uoted fo Lloyds egiste.
Tonnage is a measure of the enclosed internal volume of the vessel, 100 cubic feet representing one ton
Its normally divided into categories as follow:-
8/23/2014 15 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
1. Displacement Tonnage
A ships displaeet is the su of the ships atual eight lighteight ad its otets (deadweight).
The metric unit of measurement is 1 tonne (= 1000 Kg).
The displacement represents the amount of water displaced by the ship expressed in tonnes.
The weight of water displaced therefore equals the weight of the ship
8/23/2014 16 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
TONNE PER CENTIMETRE (TPC) It is the mass required to increase the mean draught by 1 centimetre.
LOAD DISPLACEMENT The weight of the ship and its content, measured in tonne. The value will vary according to the ships draught.
DEADWEIGHT SCALE It is a scale diagram indicating the deadweight of the ship at various draughts.
FORM COEFFICIENT It is devised to show the relationship between the form of the ship and the dimension of the ship.
8/23/2014 17 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
2. Lightweight Tonnage (LWT)
The lightweight is the weight of the ship as built (hull, machinery) including boiler water, lubricating oil and the cooling water system.
Lightweight like displacement is expressed in units of tones.
It assumes importance in a commercial sense only when considering the value of the vessel which is to be broken up for scrape.
8/23/2014 18 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
3. Deadweight tonnage (DWT)
Deadweight is the weight of the cargo which a ship carries plus weights of fuel,
stores, water ballast, fresh water, crew
and passengers and baggage.
It is the difference between the loaded ship displacement and the lightweight.
8/23/2014 19 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
4. Gross Tonnage (GT)
Measurement of total internal volume of a vessel and includes all under deck
tonnage and all enclosed spaces above
tonnage deck.
100 cubic feet of space being considered as 1 ton
8/23/2014 20 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
5. Nett Tonnage (NT)
Ship measurement derived from gross tonnage by deducting spaces allowed for crew
and propelling power.
100 cubic feet of space being reckoned as 1 ton
8/23/2014 21 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Ship side markings
LOAD LINE The marking on the ship side that relate to the loading
condition of the ship termed as the load line mark. Load line mark
consists of a ring 300 mm in outside diameter and 25 mm thick which is
intersected by a horizontal line 450 mm in length and 25 mm thick, the upper edge of which passes
through the centre of the ring. The centre of the ring is placed amidships and at a distance equal to the assigned summer freeboard measured vertically below the upper edge of the deck line.
8/23/2014 22 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
8/23/2014 23 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
8/23/2014 24 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
Sailing ship
8/23/2014 25 Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh.
ANY QUESTION?
THANK YOU! 8/23/2014
Mohd. Hanif Dewan, Chief Engineer and
Maritime Lecturer & Trainer, Bangladesh. 26