Transcript of Quick Setup Guidebsintek.basco.com/BriggsDocumentDisplay/lgipBGP.-FzXFix2.pdfC Saque el recolector...
7102731-eng:Layout 1.qxdQuick-switch 3-in-1 Convert from mulching
to bagging to side-discharge:
Read the manuals that came with your mower for:
Important safety warnings
Problem? Call 1-800-743-4115
Unpack the mower A Cut all four corners of the box from top to
bottom.
B Remove all items from around the mower. Remove the clear plastic
sheet from the top of the engine.
C Remove the grass catcher from its plastic shipping bag.
Assemble the handle A Remove the knob, lock washer, and bolt
from each side of the handle base.
B Loosen, but do not remove, the knobs on the handle. Remove the
cardboard slats.
C Lift the handle to the operating position, and tighten the upper
knobs.
D Reinsert the lower handle bolts through the handle base and
handle (most users will prefer the middle position). Install the
lock washers and fully tighten the knobs.
Set up the recoil rope handle A Hold the bail control against the
handle,
and pull the recoil rope handle out to the rope guide on the
handle. Hook the recoil rope into the rope guide (it might be a
tight fit).
Add oil and fuel A Move the mower outside to a flat, level
surface.
B Remove the oil fill cap. Add the entire contents of the supplied
oil container to the engine. Replace the oil fill cap.
IMPORTANT Mower is shipped without oil in engine. Failure to add
oil will result in engine damage.
C Remove the fuel fill cap. Add clean, fresh, UNLEADED fuel with a
minimum of 87 octane, leaving one inch of space from the top of the
tank for fuel expansion.
IMPORTANT Fuel tank holds less than 1/2 gallon. IMPORTANT DO NOT
mix oil with fuel.
D Replace the fuel fill cap, and wipe up any spills.
Read the operator’s manual for operating, maintenance, and safety
instructions
Start the mower A Move all four wheels to the desired cutting
height, and
set the mower to mulch, discharge or bag. (See Quick-switch 3-in-1
instructions below.)
B Hold the bail control against the handle.
C Pull the recoil rope handle until the engine starts.
D To engage the drive system, move the drive lever all the way
forward.
E To stop the drive system, release the bail control.
F To stop the engine and blade, release the bail control.
BTP2265HW Overview
Items that you will need Unleaded Fuel (minimum 87 octane)
Utility Knife
Items Included
Failure to read and follow instructions in the operator's manual
could result in death and/or bodily injury.
Running engines give off carbon monoxide, an odorless, colorless,
poison gas. Breathing carbon monoxide can cause nausea, fainting,
or death.
Operate this product ONLY outdoors. Keep exhaust gas from entering
a confined area through windows, doors, ventilation intakes or
other openings. DO NOT operate this product inside any building or
enclosure, even if windows and doors are open.
1
2
3
4
5
6
2 To convert to bagging: A Lift the rear door.
B Holding the rear door open, attach the grass catcher to the rear
of the mower.
C Make sure the hooks on either side of the catcher frame hook onto
the rear door rod.
D Release the rear door (it will lay on top of the grass
catcher).
3 To convert to side-discharge: A Lift the mulching cover.
B Install the side discharge deflector onto the mower deck. Make
sure the upper tabs of the deflector are hooked behind the mulching
cover rod, and the deck tabs stick up through the locking
slots.
C Release the mulching cover (it will lay on top of the side
discharge deflector).Side Discharge
Deflector
A
C
DB
A
We reserve the right to improve our products and make changes in
specifications, designs, and standard equipment without notice and
without incurring obligation.
C
A
A
A
A
B
B
Form No. 7102731 (Rev. ‘-’, 7/8/2008) TP 1099-5406---WB-J
Guía de montaje rápido Cortacéspedes BTP2265HW autopropulsado
Cambio rápido 3 en 1 Convierta del modo de trituración a
recolección en bolsa a descarga lateral:
Lea los manuales incluidos con su cortacéspedes para:
Advertencias importantes de seguridad
Instrucciones de operación
¿Problemas? Llame al 1-800-743-4115
Cómo desempacar el cortacéspedes A Corte las cuatro esquinas de la
caja empezando
por arriba.
B Retire todos los artículos que se encuentran alrededor del
cortacéspedes.Quite la lámina de plástico de la parte superior del
motor.
C Saque el recolector de césped de su bolsa plástica de
envío.
Montaje del asidero A Quite la perilla, la arandela de seguridad
y
el perno de ambos lados de la base del asidero.
B Afloje pero no quite las perillas del asidero. Retire las tiras
de cartón.
C Alce el asidero hacia su posición de operación y apriete las
perillas superiores.
D Vuelva a insertar los pernos inferiores del asidero a través de
la base del asidero y el asidero en sí (casi todos los usuarios
prefieren la posición intermedia). Instale la arandela de seguridad
y apriete bien las perillas.
Instale el mango del cable de arranque
A Oprima y mantenga oprimido el control de motor y cuchilla contra
el asidero de conducción, y hale hacia afuera el mango del cable de
arranque hasta la guía de cable en el asidero. Enganche el cable de
arranque dentro de la guía de cable (esta guía podría tener un
ajuste apretado).
Cómo añadir aceite y combustible A Ponga el cortacéspedes al aire
libre, sobre una superficie
lisa y nivelada.
B Quite la tapa de llenado de aceite. Agregue al motor todo el
contenido del recipiente de aceite suministrado. Coloque nuevamente
la tapa de llenado de aceite.
IMPORTANTE: El cortacéspedes es enviado sin aceite dentro del
motor. No agregar el aceite resultará en daño del motor.
C Quite el tapón del combustible. Añada gasolina SIN PLOMO limpia y
fresca que tenga un octanaje mínimo de 87, dejando unos 2,5 cm de
espacio hasta la parte superior del tanque que permita la expansión
del combustible.
IMPORTANTE El tanque de combustible tiene una capacidad de menos de
2 litros.
IMPORTANTE NO mezcle el aceite con el combustible.
D Vuelva a poner el tapón del combustible y limpie en caso de
derrames.
Lea el manual del usuario para instrucciones de operación,
mantenimiento y seguridad
Arranque el cortacésped A Ajuste las cuatro ruedas hasta la altura
de corte deseada, y ajuste
el cortacésped para triturar, descargar o recoger en bolsa. (Vea
abajo las instrucciones de cambio rápido 3 en 1).
B Oprima y mantenga oprimido el control de motor y cuchilla contra
el asidero.
C Hale el mango del cable de arranque hasta que arranque el
motor.
D Para engranar el sistema de impulsión de las ruedas, mueva
totalmente hacia adelante la palanca del sistema de impulsión de
las ruedas.
E Para detener el sistema de impulsión de las ruedas, suelte el
control de motor y cuchilla.
F Para detener el motor y la cuchilla, suelte el control de motor y
cuchilla.
1
2
3
4
5
6
1 Para el modo de trituración, deje en su sitio la cubierta de
reciclaje.
2 Para convertir al modo de recolección en bolsa:
A Levante la puerta trasera.
B Sosteniendo abierta la puerta trasera, sujete el recolector de
césped a la parte trasera del cortacésped.
C Verifique que los ganchos en cada lado del marco del recolector
enganchan sobre la barra de la puerta trasera.
D Suelte la puerta trasera (ésta se colocará sobre la parte
superior del recolector de césped).
3 Para convertir al modo de descarga lateral:
A Levante la cubierta de reciclaje.
B Instale el desviador de descarga lateral sobre la plataforma del
cortacésped. Verifique que las lengüetas superiores del desviador
están enganchadas detrás de la barra de la cubierta de reciclaje, y
las lengüetas de la cubierta se fijan a través de las ranuras de
enganche.
C Suelte la cubierta de reciclaje (ésta se colocará sobre la parte
superior del desviador de descarga lateral).
A
A
B
A
C
DB
A
Nos reservamos el derecho de mejorar nuestros productos y de
realizar cambios en las especificaciones, diseños y en el equipo
estándar, sin previo aviso, y sin incurrir en obligación
alguna.
C
A
A
A
A
B
B
Artículos que va a necesitar Gasolina sin plomo (octanaje mínimo de
87)
Cuchillo multiusos
(en cada rueda)
de combustible
Form. NO 7102731 (Rev. ‘-’, 7/8/2008) TP 1099-5406---WB-J
7102731-eng.pdf
7102731-spa.pdf