Presentation Modeling Part I: Intro

Using Autodesk InventorLevel: Introduction

Tweaks: TranslationAnimation

3/24/2014 - jcS Inventor - Presentations Intro -jcS

1. New: Presentation

2. Create View

3. Tweak Components

4. Animate

Linked to animation

1.INITIALIZATION

a. Startup

Start Inventor

Verify projectSelected Project

Workspace

Libraries

Folder Options

Inventor - Part Model Intro3/24/2014 - jcS Inventor - Presentations Intro -jcS

b. Open assembly file

OpenWorkspace

File name

c. New Presentation Model

NewEnglish

Standard(in).ipn

d. Create View

PresentationCreate View

Assembly File

2. TWEAK COMPONENTS

a. First Tweak - Linear

Presentation

Tweak Components

Direction (z)

Component(s)

Trans: 3

b. Second Tweak - Linear

Presentation

Tweak Components

Direction (z)

Component(s)

Drag: 3.5

c. Third Tweak - Linear

Presentation

Tweak Components

Direction (z)

Component(s)

Drag: -3.5

d. Fourth Tweak - Linear

Presentation

Tweak Components

Direction (z)

Component(s)

Drag: 3

3. ANIMATE

a. Playing the animation

Presentation Animate

Play Forward

Reverse

b. Recording the animation

Presentation

AnimateRecord

File name: FirstPres.wmv

Network Bandwidth: Broadband

Image Size: 640x480

Forward

c. Viewing the animation

Windows ExplorerFirstDemo.wmv

<RMB> Play

Linked to animation

d. Save

SaveSave in: Appropriate Folder

File name: FirstPres

Save as type: .ipn

Application: Assembly Drawing3/24/2014 - jcS Inventor - Presentations Intro -jcS

Views◦ Base (x2)

◦ Projected

Anotation◦ Centers

◦ Parts List

◦ Balloons

Other◦ Lines

Presentation Modeling Part I: Intro - Iowa State...

Transcript of Presentation Modeling Part I: Intro - Iowa State...

Presentation Modeling Part I: Intro - Iowa State...

Documents

Transcript of Presentation Modeling Part I: Intro - Iowa State...

AutoCADhome.engineering.iastate.edu/~jcshahan/AutoCAD/acadII_DrawOrg.pdf · AutoCAD Drawing Organization Layers Blocks Properties AutoCAD: Drawing Organization jcS 1/13/2013

Part Modeling II - Iowa State Universityhome.engineering.iastate.edu/~jcshahan/Inventor... · Part Modeling II Using Autodesk Inventor Features Options Properties 2/22/2014 Inventor

WESEP International Experience - Iowa State Universityhome.engineering.iastate.edu/~jdm/wesep594/WESEP...WESEP International Experience Computational blade design at Denmark Technical

Perspective / Oblique / Isometric Sketchinghome.engineering.iastate.edu/~jcshahan/Technical Graphics/109... · Perspective / Oblique / Isometric Sketching ... 3D Sketching Artistic

AutoCAD - Std Dimshome.engineering.iastate.edu/~jcshahan/AutoCAD/acadV_StdDims.pdfAUTOCAD SETTING Review Settings Adjust as needed AutoCAD: Standard Dimensions 9/6/2013 - jcs

Working Drawings Communicationhome.engineering.iastate.edu/~jcshahan/Technical...Working Drawings – Communication Jcs – 12/9/2009 1. Open Powerpoint 2. Enter a. Appropriate Title

Drawing Setup Intro - Iowa State Universityhome.engineering.iastate.edu/~jcshahan/Inventor Tutorials... · 2014-03-24 · Drawing –Setup Intro Using Autodesk Inventor 3/24/2014

Purpose of the Presentation - Iowa State Universityhome.engineering.iastate.edu/~jdm/wesep594/SelingerEnergy_Plan.pdfPurpose of the Presentation Offer Energy Plan Overview Provide

Composite Laminates - Iowa State Universityhome.engineering.iastate.edu/~mkessler/MatE454/PDF Lecture Notes... · Sectio Composite Laminates Typically, the basic building block block

Signal Modeling - Iowa State Universityhome.engineering.iastate.edu/~julied/classes/ee524/LectureNotes/l7... · Signal modeling is used for signal compression, ... Two generic model

Regionally Downscaled Climate ... - Iowa State Universityhome.engineering.iastate.edu/~jdm/wesep594...These are continental projections, what are the projections specifically for the

Infrastructure Case Study - Iowa State Universityhome.engineering.iastate.edu/~jdm/wesep594/MattColeAlliant.pdf · Overview of Balance of Plant ... Dynamic Volt-Amp Reactive ... Superimposed

Our Campus College of Engineering - Iowa State Universityhome.engineering.iastate.edu/~jdm/wind/REU_Presentation_Day_1... · •Vistagy FiberSim software for composites mfg ... College

Assembly Modeling Plus - home.engineering.iastate.eduhome.engineering.iastate.edu/~jcshahan/Inventor... · Assembly Modeling Plus Using Autodesk Inventor 2/15/2014 Inventor - Assembly

Assembly Modeling Part I: Intro - Iowa State Universityhome.engineering.iastate.edu/~jcshahan/Inventor Tutorials_jcs/0201... · Assembly Modeling Part I: Intro Using Autodesk Inventor

Section Views Conventional Practicehome.engineering.iastate.edu/~jcshahan/Technical Graphics/112_SectionView.pdfSection Views Conventional Practice 8/27/2010 - jcs Section Views .

Introduction to Planning - Iowa State Universityhome.engineering.iastate.edu › ~jdm › ee552 › PlanningIntroduction.pdfIntroduction to Planning 1 Introduction We pose some questions:

Nonlinear optimal power flow - Iowa State Universityhome.engineering.iastate.edu/~jdm/ee553/NLOPF.pdfNonlinear optimal power flow 1.0 Some introductory comments Although the LPOPF

Working Drawings Example - Iowa State Universityhome.engineering.iastate.edu/~jcshahan/Technical Graphics/115_WorkDraw.pdfdesign drawing type(s) and design drawings in general. answer

Sheet Metal Example - Iowa State Universityhome.engineering.iastate.edu/~jcshahan/Autodesk Tutorials - Invento… · Drawing2 Drawing Wew Component Model State Display Options F: