Post on 06-Jun-2018
Issue Date
April 2014
INSTALLATION
INSTRUCTIONS
Accessory Application Publication No.
MII 14925
© 2014 Honda Motor Co., Ltd. - All Rights Reserved.
PARTS LIST
87952-MJN-A0031 of 15
FOGLIGHT ATTACHMENT
P/N 08V70-MJN-A00CTX1300/A
(23)
(9)
(11)
(10)
(7)
(5)
(20)
(19)
(12)
(14)
(2)
(18)
(3)(1)
(22)
(16)
(17)
(13)
(25)
(6)
(4)
(8)
(15)
(24)
(21)
No. Description Qty
(1) Installation Instruction URL 1
(2) Fog lamp switch knob 1
(3) Fog lamp sub harness 1
(4) Right fog lamp stay 1
(5) Right fog lamp inner stay 1
(6) Right fog lamp bracket 1
(7) Left fog lamp stay 1
(8) Left fog lamp inner stay 1
(9) Left fog lamp bracket 1
(10) Fog lamp cover 2
(11) Fog lamp cap 2
(12) 6 mm shoulder socket screw 4
(13) Power relay 1
(14) 6 mm screw 4
(15) 6 mm flange nut 4
(16) Washer 4
(17) 6 mm bolt (Silver) 2
(18) Double-sided adhesive tape 1
(19) Collar 2
(20) 6 mm nut 2
(21) Flange collar (small) 4
(22) Wire tie 6
(23) 6 mm SH flange bolt 2
(24) 6 mm bolt (Black) 4
(25) Flange collar (large) 4
2 of 15
Item N·m kgf·m Ibf·ft
6 mm screw 9 0.9 6.6
6 mm shoulder socket screw 9 0.9 6.6
6 mm bolt 10 1.0 7
6 mm SH flange bolt 10 1.0 7
6 mm nut 10 1.0 7
6 mm flange nut 12 1.2 9
TORQUE CHARTTighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts.
INSTALLATION CAUTION
• To prevent burns, allow the engine, exhaust system, radiator, etc., to cool before installing the accessory.
NOTE:
• The LED fog lamp is required for the installation of this accessory.
• Heat the bonding surfaces with a hair dryer if the ambient air temperature is below 70°F (21°C).
• The adhesive reaches full strength in 72 hours. Wait at least 24 hours before riding your motorcycle.
• Disconnect the negative (-) cable from the battery before installing this accessory.
• The the clock memory will be erased when you disconnect the battery. Reset the clock after reconnecting the battery.
• Reinstall the removed parts on the motorcycle and make sure that wires and harnesses are not pinched.
• Trim the excess ends off the wire ties after attaching them to the wire harnesses. Do not allow the cut part of the wire tie to interfere with another harness or brake hose.
1. Remove the indicated clips from the left inner cover.<Left side>
LED FOG LAMP
Sold separately
(1)
(2)
No. Description Qty
(1) LED fog lamp 2
(2) LED fog lamp driver 1
TOOLS AND SUPPLIES REQUIREDSocket (8 and 10 mm)
Ratchet
Hex wrench (5 mm)
Phillips ® screwdriver
Side cutters
Marker
Ruler
Electrical tape
Isopropyl alcohol
Shop towel
Torque wrench
LEFT INNER COVER
CLIP
3 of 15
2. Remove the left inner cover, and disconnect the negative (-) cable of the battery.
LEFT INNER COVER
3. Remove the seat.
SEAT
CLIP
4. Remove the bolt, screw, and well nut from the left shroud cover as shown.
BOLT (Save)
5. Remove the left shroud cover as shown.
LEFT SHROUD COVER
<Left side>
SCREW
WELL NUT
6. Remove the right shroud cover in the same manner.
7. Remove the clip as shown.
4 of 15
8. Remove the left middle cowl as shown.
LEFT MIDDLE COWL
9. Remove the right inner cover as shown.
10. Remove the right middle cowl in the same manner as the left.
RIGHT INNER COVER
CLIP
11. Remove the left pocket as shown.
CLIP LEFT POCKETOpen the lid.
RIGHT POCKET
GROMMETRemove the grommet
from the hole.
USB CORD
HOLE
13 . Remove the USB cord as shown.
• This step is applicable only to the motorcycle
equipped with Audio.
12. Remove the USB connector in the USB connector holder.
• This step is applicable only to the motorcycle
equipped with Audio.
<Right side>
USB CONNECTOR
USB CONNECTOR HOLDER
5 of 15
BOLT
14. Remove the right pocket in the same manner as the left.
15. Remove the bolt as shown.
16. Remove the bolt and clip from the top shelter as shown.
• Repeat on the right side.
BOLTCLIP
17. Open the fuel lid and remove the wire from the tank cap as shown.
TOP SHELTER
WIRE
TANK CAP
FUEL LIDOpen.
19. Raise the front side of the top shelter and remove the right panel switch as shown.
RIGHT PANEL SWITCH
TOP SHELTER
Raise.
SCREW
18. Disconnect the connectors and move the top shelter to the rear of the motorcycle.
TOP SHELTERDisconnect the connector.
6-PIN WATERPROOF CONNECTOR (White)Motorcycle with audio only.
8-PIN WATERPROOF CONNECTOR (Gray) 3-PIN WATERPROOF
CONNECTOR (Black)
TOP SHELTER
6 of 15
20. Remove the switch as shown.
RIGHT PANEL SWITCH
SWITCH
SWITCH
SWITCH (Reuse)
SWITCH KNOB (Save)
FOG LAMP SWITCH KNOB
RIB
RIB
SCREW
22. Install the fog lamp switch knob as shown.
21. Remove the switch knob as shown.
23. Install the switch to the right panel switch in reverse order of the removal.
24. Install the right panel switch to the top shelter in reverse order of the removal.
25. Attach the double-side adhesive tape to the LED fog lamp driver as shown.
LED FOG LAMP DRIVER
DOUBLE-SIDED ADHESIVE TAPERemove the adhesive backing of
the double-side adhesive tape
before attaching.
ISOPROPYL ALCOHOLThoroughly clean the area
where the double-sided
adhesive tape will be attached.
26. Connect the fog lamp sub harness as shown.
3-PIN WATERPROOF CONNECTOR (Black)
LED FOG LAMP DRIVER
2-PIN WATERPROOF CONNECTOR (Black)
FOG LAMP SUB HARNESS
7 of 15
3-PIN WATERPROOF CONNECTOR (Black)
2-PIN WATERPROOF CONNECTOR (Black)
2-PIN WATERPROOF CONNECTOR (Black)
LED FOG LAMP DRIVER
FOG LAMP SUB HARNESS
FOG LAMP SUB HARNESS
FOG LAMP SUB HARNESS
FOG LAMP SUB HARNESS
POWER RELAY
ELECTRICAL TAPE
ELECTRICAL TAPE
POWER RELAY
POWER RELAY
27. Install the wire tie to the power relay as shown.
WIRE TIE
WIRE TIESecure the power relay to the recess
of the 3-pin waterproof connector.
WIRE TIE
28. Connect the power relay as shown.
29. Secure the power relay as shown.
30. Fold back the fog lamp sub harness and secure it with the electrical tape as shown.
POWER RELAY
5-PIN CONNECTOR (White)
ISOPROPYL ALCOHOLThoroughly clean the area where the LED
fog lamp driver will be attached.
31. Clean the surface of the area shown using isopropyl alcohol.
<Right side>
8 of 15
33. Remove the dummy connector as shown.<Right side>
MOTORCYCLE’S 4-PIN WATERPROOF CONNECTOR (Black)
4-PIN WATERPROOF DUMMY CONNECTOR (Black) (Save)
FOG LAMP SUB HARNESS
LEFT FRONT FORK
FOG LAMP SUB HARNESS
34. Route the fog lamp sub harness as shown.
2-PIN WATERPROOF CONNECTOR (Black)
CORD (White/Blue)
<Left side>
MOTORCYCLE’S 4-PIN WATERPROOF CONNECTOR (Black)
4-PIN WATERPROOF CONNECTOR (Black)
FOG LAMP SUB HARNESS
35. Connect the fog lamp sub harness as shown.
LED FOG LAMP DRIVERRemove the adhesive backing
before attaching.
LED FOG LAMP DRIVER
32. Install the LED fog lamp driver as shown.
9 of 15
2-PIN WATERPROOF CONNECTOR (Black)
2-PIN WATERPROOF CONNECTOR (Black)
FOG LAMP SUB HARNESS
36. Secure the connector as shown.<Left side>
ELECTRICAL TAPESecure the fog lamp
sub harness to the
motorcycle’s harness.
ELECTRICAL TAPE
37. Install the top shelter and right and left pocket in reverse order of the removal.
• Confirm that no wire or harness is caught or
too tight.
38. Route the fog lamp sub harness as shown.<Right side>
FOG LAMP SUB HARNESS
3-PIN WATERPROOF DUMMY CONNECTOR (Black) (Save)
CLIP BAND
3-PIN WATERPROOF CONNECTOR (Black)
39. Remove the dummy connector as shown.
WIRE (White/Blue)
FOG LAMP SUB HARNESS
3-PIN WATERPROOF CONNECTOR (Black)
CLIP BAND
40. Secure the connector as shown.
10 of 15
44. Loosely install the assembled left fog lamp inner stay as shown.
LED FOG LAMP
6 mm SCREW
WASHER
LEFT FOG LAMP INNER STAY
LEFT FOG LAMP INNER STAY
LED FOG LAMP HARNESS
45. Install the 6 mm nut to the LED fog lamp as shown.
6 mm NUTASSEMBLED LEFT LED FOG LAMP
43. Install the flange collars to the left fog lamp inner stay as shown.
FLANGE COLLAR (small)
3-PIN WATERPROOF CONNECTOR (Black)
41. Connect the fog lamp switch harness as shown.
FOG LAMP SWITCH HARNESS
42. Mark the LED fog lamp harness at the position with the indicated dimensions.
• Perform this step for both fog lamps.
LED FOG LAMP
290 mm
MARKER
LED FOG LAMP HARNESS
11 of 15
46. Install the left fog lamp stay as shown.
ASSEMBLED LEFT LED FOG LAMP
COLLAR
LEFT FOG LAMP STAY
6 mm BOLT (Silver)
LEFT FOG LAMP STAY
RIB
Put the end of the left fog lamp stay to the rib.
6 mm SCREWTighten the left
and right screws
securely.
LEFT FOG LAMP STAY
6 mm SH FLANGE BOLT
ASSEMBLED LEFT LED FOG LAMP
LEFT FOG LAMP INNER STAY
47. Secure the left fog lamp inner stay and left fog lamp stay as shown.
• To adjust the fog lamp aim, loosen the 6 mm
SH flange bolt and 6 mm screws.
48. Install the left fog lamp bracket as shown.
• To adjust the fog lamp aim, loosen the 6 mm
flange nuts.
6 mm FLANGE NUT
LEFT FOG LAMP BRACKET
ASSEMBLED LEFT LED FOG LAMP
49. Install the fog lamp cover as shown.
FOG LAMP COVER
ASSEMBLED LEFT LED FOG LAMP
Align the LED fog lamp with the tabs of the fog lamp cover.
ASSEMBLED LEFT LED FOG LAMP
<Back side>
TAB
FOG LAMP COVER
12 of 15
LEFT FOG LAMP BRACKET
52. Secure the left LED fog lamp harness as shown using a wire tie.
ASSEMBLED LEFT LED FOG LAMP
WIRE TIESecure the left LED fog lamp
harness to the left fog lamp
bracket.
53. Repeat Steps 43 through 52 to assemble the right LED fog lamp in the same manner.
LEFT LED FOG LAMP HARNESS
54. Route the left LED fog lamp harness to the left shroud cover as shown.
ASSEMBLED LEFT LED FOG LAMP
LEFT LED FOG LAMP HARNESS
LEFT SHROUD COVER
50. Secure the fog lamp cover as shown.
FOG LAMP COVER
6 mm SHOULDER SOCKET SCREW
Install with both clear apertures aligned.
51. Route the left LED fog lamp harness and install the fog lamp cap as shown.
FOG LAMP CAP
FOG LAMP COVER
CLEAR APERTURE
CLEAR
APERTURE
FOG LAMP CAP
ASSEMBLED LEFT LED FOG LAMP
6 mm SHOULDER SOCKET SCREW
LEFT LED FOG LAMP HARNESS
LEFT LED FOG LAMP HARNESS
13 of 15
ASSEMBLED LEFT LED FOG LAMP
LEFT LED FOG LAMP HARNESS
WIRE TIESecure the left
LED fog lamp
harness at the
marked point
to the left
shroud cover.
LEFT SHROUD COVER
MARK
55. Secure the left LED fog lamp harness as shown.
56. Repeat Steps 54 and 55 on the right side.
Loosely install the fog lamp as shown and connect the
connectors.
57. Connect the left LED fog lamp harness as shown.<Left side>
LEFT LED FOG LAMP HARNESS
LEFT SHROUD COVER
FOG LAMP SUB HARNESS
2-PIN WATERPROOF CONNECTOR (Black)
ASSEMBLED LEFT LED FOG LAMP
6 mm BOLT (Black)
LEFT SHROUD COVER
14 of 15
Loosely install the fog lamp as shown and route the
harness.
6 mm BOLT (Black)
RIGHT LED FOG LAMP HARNESS
RIGHT SHROUD COVER
60. Route the right LED fog lamp harness as shown.<Right side>
ASSEMBLED RIGHT LED FOG LAMP
RIGHT SHROUD COVER
58. Remove the loosely installed left LED fog lamp and install the left middle cowl in the reverse order of removal.
• Install the left middle cowl so as not to apply
an excessive force on the left LED fog lamp
harness.
• Confirm that no wire or harness is caught or
too tight.
59. Install the left shroud cover in the reverse order of removal, and then install the left LED fog lamp as shown.
• Confirm that no wire or harness is caught or
too tight.
<Left side>
ASSEMBLED LEFT LED FOG LAMP
6 mm BOLT (Black)
FLANGE COLLAR (large)
LEFT SHROUD COVER
15 of 15
2-PIN WATERPROOF CONNECTOR (Black)
6 mm BOLT (Black)
FLANGE COLLAR (large)
RIGHT LED FOG LAMP HARNESS
ASSEMBLED RIGHT LED FOG LAMP
RIGHT SHROUD COVER
62. Remove the loosely installed right LED fog lamp and install the right middle cowl in the reverse order of removal.
• Install the right middle cowl so as not to apply
an excessive force on the right LED fog lamp
harness.
• Confirm that no wire or harness is caught or
too tight.
63. Install the right shroud cover in reverse order of the removal, and then install the right LED fog lamp as shown.
• Confirm that no wire or harness is caught or
too tight.
<Right side>
LED FOG LAMP DRIVER
FOG LAMP SUB HARNESS
61. Connect the fog lamp sub harness to the right LED fog lamp harness as shown.
<Right side>
64. Connect the negative (-) cable to the battery and check each light for function.
65. Perform the ADJUSTING THE FOG LAMP AIM.
66. Install the motorcycle’s parts in the reverse order of removal.
• Confirm that no wire or harness is caught or
too tight.
MOUNTING HEIGHT of FOG LAMP
5 m
CUT-OFF LINE
MOUNTING HEIGHT of FOG LAMP
AIMING THE FOG LAMP1. Place the motorcycle on a level surface, 5 m away
from the aiming screen. Turn on the fog lamps.
• When the main switch is ON and the fog lamp switch is pressed, a fog lamp lights up.
• When the fog lamp switch is pressed again, the fog lamp is turned off.
2. Measure the mounting height of the fog lamp from the floor.
3. Aim the fog lamps so that the cut-off line of the light pattern on the aiming screen is the some distance above the floor as the fog lamp mounting height.
FOG LAMP SWITCH