Office Supplier of TPMS for Dongfeng-Nissan and Tesladigitire.nl/Presentation of...

Office Supplier of TPMS for Dongfeng-Nissan and Tesla

Introduction of Valor TPMS-203(With transceiver)

Why TPMSIntroduction of Valor TPMSTarget Market FunctionsCharacteristicsOperationComparison with Other TPMSAwards & Certificates Benefit from Valor TPMS

Why TPMS?

■Truck fleets recognize that tires are "capital goods" for them.

■The deficiency of pressure is 0.6 bar, the rolling resistance increases by 20%, which can increase fuel consumption by 6% and overall expenditure by close to 2 %.

■ Professional tire resource management, therefore, can significantly lower operating cost-per-mile.

*Source: Michelin

Approximate 75% of all running tires are underinflated.-U.S.A National Highway Traffic Safety Administration

An estimated 23,464 crashes and 535 fatal crashes annually involve blowouts or flat tires.

-The Fatality Analysis Reporting System of USA

Accident Caused By Under-inflated Tire

A tire20% underinflated has a running life 30% less30% underinflated has a running life 45% less20% overinflated has a running life 10% less

Decreased Tire Life with Lower Pressure (Source: Continental Tires)

Tire Loss

According to Continental Tires’ research, we assume that:* Average yearly tire loss is between 15%;*There is around 15% from blow-out, 80% of blow-out is from under-inflated;*TPMS can help fleet to extend tire life at least 20%;*Average price of a truck tire is EUR300.00.

Thus, a 100 12-wheel fleet would save:21.6 pcs blow-out tires which are worth 6,480 EURO;Tire life about 30.6 pcs which are worth 9,180 EURO.

* ThereforeWith TPMS Whole fleet can save:(6,480 + 9,180) = 15,660EURO/year on tires.156.6 EURO of tire saving for one truck in one year.

This Figure has shown us that the corresponding effect of inflation pressure on the fuel consumption of a typical tractor-trailer at 55 MPH on a level highway. 20% percent under-inflation of tires results in about a 3 percent decrease.

Fuel Loss

According to Goodyear’s research, we assume that:* 50% of a year is running under-inflated * Fuel Consumption (Without TPMS): 39.2 L/ 100km* Avg. Annual Fuel Consumption : 6,6640 L* Fuel Cost Per Year: 85,299.2 € (1.28 €/L—Avg. retail price

per litre in Europe October 2008)

A 100 vehicles fleet covering an average of 170,000 km each per year would save:

100 x 85,299.2€ x 50% x3 %=127,949 €

It is difficult to visually determine the under-inflated level, as the 30% pressure lower looks like proper inflated tire.

-Office of Crash Avoidance Standards, NHTSA

TPMS provides an early warning on abnormal pressure & temperature!

100% Inflation 70% Inflation

Introduction

Tire Pressure Monitoring System (TPMS) for trucks and buses is a valuable vehicle safety device that drivers should always consider.

Valor TPMS provide peace of mind and safety, maximize fuel savings and tire life, and environment-friendly.

Safety

Savings

Environment

Valor TPMS-203 has been developed specifically for the challenges of tire pressure monitoring on large-scale and multi-wheeled fleets operating in fast-moving logistics.

Each battery-powered wheel transmitter installed inside the tire measuring the pressure and temperature every 4 seconds, the data of tractor wheels are sent to display directly, the data of trailer wheels are sent to transceiver which transfer to display wirelessly. The integrated display evaluates the data, identifies the transmitter and decides whether or not the driver needs to be informed.

Each display has an exclusive ID register, they have same ID code. The ID register is used to send the ID code to transceiver so that the transceiver can confirm which display it should transfer data to.

Office Supplier of Tire Service Products for Ford, GM and Chrysler

ID Register

Mounting Diagram

Target Market

Valor TPMS-203 is applied for:

●Medium and heavy duty trucks●Trucks with trailers ● Specialty vehicles● Buses

Principle of TPMS-203

TPMS is abbreviation of Tire Pressure Monitoring System, it’s a reliable proactive safety device which always monitors pressure and temperature of each tire in both driving and parking. If the sensor gets the abnormal conditions such as high pressure, low pressure, high temperature and leakage, it will immediately send signal toreceiver wirelessly, then the display gives driver an alarm of danger.

The system consists of receiver-display, transmitter, transceiver, ID register and antenna.

Principle of TPMS-203

Display

Transceiver

Transmitter

ID Register Antenna

Components

Fixed in rim channelpressure and

Temp. Sensor

RF TransmitterB

attery

Principle of Transmitter (or Sensor) Transmitter consists of temperature & pressure sensor, MCU, RF transmitter and battery, They are integrated in one plastic housing. The sensor in transmitter detects changes of tire pressure and temperature, transforms the changes to electrical data through electrical components, then MCU transforms the electrical data and the ID code to digital signal, which the RF transmitter sent out. The transmitter could be triggered when it detects the pressure lower than settings.

RF Receiver

Power 12V / 24V

Receiving

Principle of Transceiver

RF TransmitterTransmitting

Transceiver consists of MCU, RF receiver, RF transmitter and ID module, They are integrated in one plastic housing. The RF receiver receiving digital signal sent by transmitter and transfer it to MCU which will demodulate the signal, then the RF transmitter will send it out to display together with the ID number of trailer transmitters.

The receiver and display is integrated, the receiver receives signal from transmitter via antenna and demodulate it, then the display shows the data, the process is controlled by MCU. When the received pressure and temperature is lower or greater than the setting value, MCU will order the display to warn the driver by lighting or sound. Driver then could take positive actions.There are at least 6 sensors in the truck to transmit data, that is, the receiver will get data from multiple sources at the same time. Each sensor has a corresponding ID module in the MCU, so the receiver can get the right data of each corresponding tires.

Receiver

Display

12V or 24V

ID MODULE

Antenna

Principle of Receiver and Display

Functions

In order to make drivers in heavy-vehicles can see the displayed pressure and temperature more clearly and conveniently, we designed a large display with large digits.

Pressure unit

Leakage symbol

pressure and temperature warning symbol

pressure & temp.switch

tire position switch

Temperature unit

Display

The display will monitor tires 24 hours and show each axle tires’ pressure for 5 seconds and automatically switch to next axle when all tires are normal. If you want to check all tires’ temperature, please shortly press the “Pressure & Temperature Switch”, the display begins to show the temperature of each axle circularly. Press the “Pressure & Temperature Switch” to shift pressure interface and temperature interface from each other.

Display in Normal Condition

Pressure Interface Temperature Interface

When current pressure in the tire is 20% lower than baseline pressure: ①Display show the pressure of axle with abnormal tire; ②Warning sound “Di-Di”; ③Abnormality icon “ ” appears; ④The digits of abnormal wheel position twinkle.

The figure shows”2C” tire is underinflated. The display will always show the axle 2until the problems are corrected.

Low Pressure Warning

When current pressure in the tire is 30% higher than baseline pressure: ①Display show the pressure of axle with abnormal tire; ②Warning sound “Di-Di”; ③Abnormality icon “ ” appears; ④The digits of abnormal wheel position twinkle.

The figure shows “2D” tire is over-inflated. The display will always show the axle 2until the problems are corrected.

High Pressure Warning

When temperature inside tire is higher than 80℃ (176℉): ①Display show the temperature of axle with abnormal tire; ②Warning sound “Di-Di”; ③Abnormality icon “ ” appears; ④The digits of abnormal wheel position twinkle.

The figure shows “2B” tire is over-hot. The display will always show the axle 1 until the problems are corrected.

High Temperature Warning

When 0.33 Bar is lost from the tire in 16 seconds: ①Display show the pressure of axle with abnormal tire; ②Warning sound “Di-Di”; ③Leakage icon “ ” appears; ④The digits of abnormal wheel position twinkle.

The figure shows “2B” tire is leaking. The display will always show the axle 2 and until the problems are corrected.

Leakage Warning

System Characteristics

Tire Identification--ID Module Technology

Why do we need tire identification?

When tire pressure sensor was replaced or a spare tire is mounted, the new sensor will be in an “asleep” mode. To wake up sensor, it must be registered.

Each time a wheel sensor rotation occurs, the tire pressure sensors must be relearned. If a tire and wheel rotation is not followed by the relearned procedure, the system will not properly inform the driver with the correct location on the vehicle for a low or high pressure tire.

Valor TPMS ID Module Technology

Each transmitter has a corresponding ID module, they have same exclusive ID code, such as 01EB327F. The ID module is installed in the back of display or in the transceiver to register the ID code and identify the tire position.

Digitire TPMS ID Module Technology

----position relation between display and ID module seat

Axle 1

Axle 2

Axle 3

Axle 4

Axle 5

Axle 6

1A 1B 1C 1D

2A 2B 2C 2D

3A 3B 3C 3D

A B C D

6 axles

---- Position of ID modules and transmitters

No transceiver for straight vehicles/buses/OTR vehicles

For trucks with trailers, install tractor ID modules in the display and trailer ID modules in the transceiver.

IdentificationThe ID code together with the tire pressure and temperature will be sent to display, which will match the transmitter with its corresponding ID module.

RotationThe ID module position resembles tire’s position as the pictures above, if you interchange wheel position, you should also interchange the position of ID module. For example, if you interchange wheel 1C and 4C, you should also interchange the position of ID module 1C and 4C.

Change TransmitterWhen you replace a sensor, first install the new sensor in the wheel, then plug the ID module came with the sensor in the corresponding position. For example, if you replace the sensor in wheel 2D, you should plug the new ID module in the position 2D.

The Merit of ID Module Technology

Recalibration or complicated setup is unnecessary when doing tire rotation or changing transmitter.

All tires transmitting data at the same time will interference each other. Our program can effectively reduce these data interference to about 3%.

High Anti-interference Ability

High-performance chip and high-frequency circuit ensure the high quality transmitting and receiving of signal even in high driving speed.

The transmitting and receiving of the signal are stable at highest speed of 250km/h.

High Reliability of Signal

High-quality cell and extremely optimized circuit design guarantees the battery life up to 5 years.

5 years

Low Energy Consumption

Using pressure sensor provided by famous sensor supplier GE which have a measuring range of 0-13bar(0-188psi) to satisfy different kinds of model.

Pressure Measuring Range

Operation

Setup the Baseline PressureIt’s necessary to set baseline pressure on the following conditions:① First use of product.② Replace transmitter and ID module.

Both tractor and trailer need to be set up

The baseline pressure has been set in the factory at 4Bar (58PSI) for all wheel positions. We recommend that you set the baseline pressure at the same pressure as standard cold inflation pressure recommended by tire manufacturer.

Setup the Baseline Pressure of Tractor

1. Inflate all tires’ pressure to the standard cold inflation pressure.

2. Press the SET KEY for five seconds, you will hear sound “beep”, all backlights are on, the screens show “000”, which means you succeed in deleting the old baseline pressure.

3. Go next step---setup the baseline pressure of trailer.

Set Key

Setup the Baseline Pressure of Trailer

1. Inflate all tires’ pressure to the standard cold inflation pressure.2. Turn on the transceiver.3. Press the SET key for five seconds, you will hear sound “beep…..”, the green light is on, which means you succeed in deleting the old baseline pressure.

The display & transceiver will exit setup mode automatically after receiving signal from transmitter. The first pressure value received will be saved as new baseline pressure automatically.

The system has to be restarted to re-identify the ID module in the following situations:1) Tire rotation;2) Trailer interchange;3) Replace transmitter & ID module;To restart the system, please first turn off the display and transceiver and then turn on again.

Restart the System

Restart Key

Trailer ChangeBecause the connection between tractor and trailer is wireless, so trailer change is very easy: disconnect trailer ① and turn off transceiver, then connect trailer ② and turn on transceiver.

Restart the system.

Installation

Installation of Display

Fix the cupule pedestal on the back of display, wipe off any dirt on the windshield and fix the cupule pedestal on the windshield by pressing the cupule tightly, make sure it’s in driver’s field of vision.

Installation of Transmitter1. Loose the steel strap. Wrap the strap around the rim in the lowest spot and mark it 5 cm (2”) past worm gear (see Figure 1).

2. Cut the extra strap tapered and rasp away the edge (see Figure 2).

Figure 1 Figure 2

3. Install the tapered end of the strap through the opening of the cradle. Remove the adhesive tape liner from cradle. Keep the strap parallel with the wheel flange and ensure the strap is positioned in the lowest spot possible for correct transmitter and cradle retention.

4. Position worm gear 8” (10 cm) away from the edge of the sensor and tighten worm gear until the sensor can not be moved (see figure 4).

Figure 3 Figure 4

Installation of Cables

Connect the power wire and antenna extension cable with display. Place the cable underneath the rubber layer around the edge of windshield towards circuit box and chassis respectively.

Install power wire: Correctly connect the red wire and blue wire with positive poleand cathode respectively. Tie up all the cables with a strap and put in the compartment, then replace the cover of circuit box

Install antenna of tractor: Make the antenna extension cable along the vehicle existing umbilical harness extending to the chassis of tractor, screw the antenna onto the antenna extension cable and fix the terminal of antenna on the chassis in the front of second axle with magnet.

Install antenna of trailer: Screw the antenna extension cable on the transceiver; place the cable along the chassis harness extending to the front of axle, use magnet to fix the antenna on the chassis.

Installation of Transceiver

Connect to power

Connect with antenna installed under the

chassis of trailer

switch

Set keySender: send information to

display wirelessly

Magnets used to fix on the trailer

Use magnets to fixthe transceiver on the trailer

Side elevation of Installation

Awards & Certificates

ISO/TS 16949:2002

e-mark: e13*72/245*95/54*3539*00

E-mark

FCC ID:TZSTPMS201

Certificate No.: R07041010

Product InsuranceProduct liability insurance: US$2,000,000.00

AAPEX Award

■TPMS-201 was granted the “New Product Showcase Winner of AAPEX 2006”■ Only 8 products won such award among more than 2,000 products.

Benifit from Valor TPMS

Advertisement all over the worldInternet: www.baolong.biz www.digitire.comwww.google.com www.globalsources.comwww.gasgoo.com/ www.alibaba.comwww.made-in-china.com www.ebay.comwww.ec21.com www.busytrade.com

MagazineGlobalsources Tyres & Accessories

ExhibitionsEvery year we participate about 10 world exhibitions.Such as AAPEX, SEMA, CES, SAE, AUTOPROMOTEC,ESSEN, IAA FRANKFURT, and so on.

Attractive Price

E-mail us at: sbic@baolong.biz for more information

Delivery by air

Total lead-time: 3~4 weeks

Production: 2~3 weeks

Transportation:

1 week

Short Lead Time

Totally 3~4 weeks

Promotional Materials

Pamphlet

Give a brief introduction of the Valor TPMS s u c h a s t h e r o l e o f T P M S , t h e specif ications and features of Valor TPMS, etc.

*One kit of TPMS with one free pamphlet

Make Your Wheels Go The Distance!

Shanghai Baolong Automotive Corporation 71 MaoSheng Rd, Dongjing, Songjiang, Shanghai 201619, China

Tel: +8621 5769 0000 (200 Lines)Fax: +8621 5769 0035

E-mail: sbic@baolong.bizWeb: www.baolong.biz www.digitire.com

Office Supplier of TPMS for Dongfeng-Nissan and Tesladigitire.nl/Presentation of...

Documents

Transcript of Office Supplier of TPMS for Dongfeng-Nissan and Tesladigitire.nl/Presentation of...

MITCHELL DIAGNOSTICS OPTIONAL ACCESSORIES: …...MITCHELL DIAGNOSTICS™ OPTIONAL ACCESSORIES: TPMS RESET KIT Transfers TPMS registration from the Bluetooth wireless TPMS sensor directly

EQUITY RESEARCH Dongfeng

DILL TPMS APPLICATIONS CHART - Your Tire Shop Supply TPMS APPLICATION GUID… · dill tpms applications chart ...

Dongfeng Zb25!35!45 Operator Manual

TPMS Application Guide - Professional Tire Repair, TPMS ...31inc.com/TPMS.pdf · TPMS Application Guide VEHICLE INFORMATION SERVICE KIT INFORMATION OEM INFORMATIONSENSOR REPLACMENT

2011 dongfeng nissan SUNNY idle learning operation method. · 2018. 4. 17. · 2011 dongfeng nissan SUNNY idle learning operation method. Dongfeng Nissan SUNNY，2011，VIN=LGBP12E2XBY0*****。After

TPMS Function List Software Version: 16.80 TPMS Europe ...

VDO TPMS Pro · User manual VDO TPMS Pro UM-366EVD-U User manual VDO TPMS Pro 2/58 User guide VDO TPMS PRO TOOL 1. SPECIFICATIONS Battery Type: Rechargeable Lithium Ion Battery Life:

Tpms Ixd Small

TIRE PRESSURE MONITORING SYSTEMS CATALOG 2012 Supply_2012 TPMS Catalog.pdf · 4 CATEGORY NAME ASCOT SUPPLY TPMS CATALOG | 2012 SUPPLY CORPORATION TPMS RELEARN CHART 2011 TIA TPMS

Mitsureset - ATEQ TPMS

TPMS Network

NAPA Echlin TPMS

TpMS - Evtsr.com · TPMS Application Cap (100 Per Box) TR3569 TPMS Grommet Removal Tool TR25985 Torque Tool For TR20008 TPMS Replacement Stem OPK860 TPMS Sealing Cap Kit (320 Pcs)

DongFeng Motors

FOTON, DONGFENG, CUMMINS PARTS

orange tpms manual

Tpms Crx 1010 Manual

operating the TPMS TPMS Manual - Orange Electronic

Relations Between Foreign and Chinese Automobile Manufacturers … · 2021. 4. 22. · Parts 44% Dongfeng \ Honda Dongfeng Engine Honda 50% 50% Dongfeng Peugeot Citroen 50% DF Nissan