ISS/EEEIEC-56/1987DIN 462771 EC.TC-37ANSI/IEEE-C.62.11 (1982)IEE-99-4IEC-99-4IEC-60099-4IEC 129IEC 168IEC 186IEC 815IEC 1330IEC 694IEC 298IEC 265IEC 60129IEC 298CL 1001IEC 947IEEE 80-2000BS 1858/57ISO 75IEC 60695-2-12IEC 60695-10-2UL 94IEC 62056-21IEC 62052-11IEC 62053-21IEC 60068IEC 61036-1996CEA Regulation 2006CBIP Technical report No. 88IEC 529IEC 1107ANSI/IPC-A-610ASTMD 570REC specification no. 18/1981ANSI C 119.4BS 84ISS 206-2A grskor

Electricity (Supply ) Act 1948Indian Electricity Rules 1956India Electricity Act 1910

SL. NO. IS CODES/STANDARDS1 IS 5:20072 IS 209-1992 (Reaff. 2003)

5 IS 269-2013

6 IS 278-2009

7 IS 280-2006

9 IS 307-1966 (Reaff. 1996)10 IS 325-199611 IS 335-1993 (Reaff. 2005)12 IS 456-2000 (Reaff. 2005)13 IS 513-2008

14 IS 632-1978 (Reaff. 2012)

15 IS 692-1994 (Reaff. 2000)

16 IS 731-1971

17 IS 814-2004

20 IS 1069-1993 (Reaff. 2003)

21 IS 1079-2009

22

23 IS 1248 (Part-1)-2003

24 IS 1255-1983 (Reaff. 1996)

25 IS 1271-1985 (Reaff. 2001)

26 IS 1340-1977 (Reaff. 2006)

27 IS 1343-2012

28 IS 1365-2005/ISO 2009-1994

IS 1180 (Part-1)-1989 (Reaff. 1993)

29

30

31

32

33 IS 1573-1986 (Reaff. 2006)

34 IS 1651-1991 (reaff. 2002)

35 IS 1652-1991 (Reaff. 2002)

36 IS 2004-1991 (Reaff. 2001)

37 IS 2016-1967 (Reaff. 2001)38 IS 2026 (Part-1)-2011

39

40 IS 2062-2011

41

101

IS 1367 (Part-1)-2002/ISO 8992-1986

IS 1367 (Part-2)-2002/ISO 4759-1-2000 (Reaff. 2002)

IS 1367 (Part-3)-2002/ISO 898-1-1999

IS 1554 ( Part 1 ) - 1988 (Reaff. 1999)

IS 2026 (Part-3)-2009/ lEC 60076-3 : 2000

IS 2071(Part-1)-1993/IEC Pub eO-1 ( 1989 ) (Reaff. 2004)

IS 9921 (Part-II)-1982 (Reaff. 2002)

DETAILS

ZINC INGOT - SPECIFICATION

SPECIFICATION FOR CARBON DIOXIDETHREE-PHASE INDUCTION MOTORS -SPECIFICATIONNEW INSULATING OILS- SPECIFICATIOPLAIN AND REINFORCED CONCRETE - CODE OF PRACTICECOLD REDUCED LOW CARBON STEEL SHEET AND STRIP

HOT ROLLED CARBON STEEL SHEET AND STRIP - SPECIFICATION

PRESTRESSED CONCRETE — CODE OF PRACTICE

COLOURS FOR READY MIXED PAINTS AND ENAMELS

ORDINARY PORTLAND CEMENT, 33 GRADE — SPECIFICATION

GALVANIZED STEEL BARBED WIRE FORFENCING — SPECIFICATION

MILD STEEL WIRE FOR GENERAL ENGINEERINGPURPOSES

SPECIFICATION FOR GAMMA-BHC ( LINDANE) EMULSIFIABLE CONCENTRATES

PAPER INSULATED LEAD SHEATHED CABLES FOR RATED VOLTAGE UPTO AND INCLUDING 33 KV-SPECIFICATION

SPECIFICATION FOR PROCELAIN INSULATORS FOR OVERHEAD POWER LINES WITH A NOMINAL VOLTAGE GREATER THAN 1000 V

COVERED ELECTRODES FORMANUAL METAL ARC WELDING OFCARBON ANDCARBON MANGANESE STEEL- SPECIFICATION

QUALITY TOLERANCES FOR WATER FOR STORAGE BATTERIES - SPECIFICATION

OUTDOOR TYPE THREE-PHASE DISTRIBUTION TRANSFORMERS UPTO AND INCLUDING 100 KVA 11 KV-SPECIFICATION (PART 1-NON SEALED TYPE)

DIRECT ACTING INDICATING ANALOGUE ELECTRICAL MEASURING INSTRUMENTS AND THEIR ACCESSORIES (PART-1 DEFINITIONS AND GENERAL REQUIREMENTS)

CODE OF PRACTICE FOR INSTALLATION AND MAINTENANCE OF POWER CABLES UP TO AND INCLUDING 33 kV RATING

SPECIFICATION FOR THERMAL EVALUATION AND CLASSIFICATION OF ELECTRICAL INSULATION

CODE OF PRACTICE FOR CHROMATE CONVERSION COATING ONZINC AND CADMIUM COATED ARTICLES AND ZINC BASE ALLOYS

SLOTTED COUNTERSUNK FLAT HEAD SCREWS (COMMON HEAD STYLE) – PRODUCT GRADE A

SPECIFICATION FOR PLAIN WASHERSPOWER TRANSFORMERS PART 1 GENERAL

TECHNICAL SUPPLY CONDITIONS FOR THREADED STEEL FASTENERS PART 1 GENERAL REQUIREMENTS FOR BOLTS, SCREWS AND STUDS

TECHNICAL SUPPLY CONDITIONS FOR THREADED STEEL FASTENERS PART 2 TOLERANCES FOR FASTENERS — BOLTS, SCREWS, STUDS AND NUTS — PRODUCT GRADES A, B AND C

TECHNICAL SUPPLY CONDITIONS FOR THREADED STEEL FASTENERS PART 3 MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL — BOLTS, SCREWS AND STUDS

SPECIFICATION FOR PVC INSULATED ( HEAVY DUTY )ELECTRIC CABLES PART 1 FOR WORKING VOLTAGES UP TO AND INCLUDING 1 100 V

SPECIFICATION FOR ELECTROPLATED COATINGS OF ZINC ON IRON AND STEEL

STATIONARY CELLS AND BATTERIES, LEAD-ACID TYPE ( WITH TUBULAR POSITIVE PLATES ) - SPECIFICATION

STATIONARY CELLSAND BATTERIES, LEAD-ACID TYPEWITH PLANTE POSITIVE PLATES- SPECIFICATION

CARBON STEEL FORGINGS FOR GENERAL ENGINEERING PURPOSES-SPECIFICATION

POWER TRANSFORMERS PART'3 INSULATION LEVELS, DIELECTRIC TESTS AND EXTERNAL CLEARANCES IN AIR

HOT ROLLED MEDIUM AND HIGH TENSILE STRUCTURAL STEEL — SPECIFICATION

HIGH VOLTAGE TEST TECHNIQUES PART 1 GENERAL DEFINITIONS AND TEST REQUIREMENTS

SPECIFICATION FOR ALTERNATING CIJRRENT DISC-ONNECTORS(ISOLATORS) AND EARTHING SWITCHES FOR VOLTAGES ABOVE 1000 V PART II RATING