Post on 30-Jan-2021
INSTALLATION INSTRUCTIONS FOR PART 99-7008
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
• DIN Radio Provision with pocket• ISO Radio Provision with pocket
A) Radio Housing B) ISO Brackets C) ISO Trim Plate
KIT COMPONENTS
TOOLS REQUIRED:
99-7008
APPLICATIONS
2003-2006Mitsubishi Outlander
CBA
• Phillips Screwdriver Panel Removal Tool orSmall Flat Blade Screwdriver
Dash Disassembly ............................................................................ 1
Kit AssemblyDin Mount Radio Provision with pocket..........................................................2ISO Mount Radio Provision with pocket..........................................................3
Final Assembly ................................................................................. 4
99-7008
TABLE OF CONTENTS
2003-2006 Mitsubishi Outlander
99-7008 DASH DISASSEMBLY
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Remove all (3) climate control knobs.(Figure A)
2
MITSUBISHI OUTLANDER 2003-2006
Remove (2) Phillips head screwsfrom behind the (2) outside climatecontrol knobs. (Figure A)
3
Unsnap the top edge of the trimpanel below the Climate controls. Itis not necessary to completelyremove this panel. (Figure B)
4
Unsnap and remove the radio/climatecontrol trim panel. (Figure C)
5
A
B
C
1
Remove (4) Phillips head screwssecuring the radio. Unplug andremove the radio.
6
2
Slide the DIN cage (supplied with radio)into the Radio Housing from the front. (Figure A)
1
A
Slide the radio into the DIN cage until itsnaps into place. (Figure C)
3
DIN MOUNT RADIO PROVISION WITH POCKET
B
99-7008 KIT ASSEMBLY
Secure DIN cage to radio housing bybending the locking tabs outward.(Figure B)
2
Continue to final assembly.
C
3
Align the holes in the ISO brackets withthe holes in the radio. Mount thebrackets to the radio using screwssupplied with the radio. (Figure A)
1
A
B
Slide the radio/bracket assembly into theradio housing until it snaps into place.(Figure B)
2
Snap the ISO trim-plate onto the front ofthe assembled radio and housing.(Figure C)
NOTE: To remove the radio unsnap and remove the ISO trim-plate. Using a flatblade screwdriver disengage ISO brackets from the radio housing and slideradio out of radio housing.
3
ISO MOUNT RADIO WITH POCKET
99-7008 KIT ASSEMBLY
Continue to final assembly.
C
4
FINAL ASSEMBLY1 Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections asshown. (Isolate and individually tape off the ends of any unused wires to preventelectrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individuallytape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-) . . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
99-7008 FINAL ASSEMBLY
3
5
99-7008
NOTES
99-7008 INSTRUCTIONS
1-800-221-0932 www.metraonline.com© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-7008REV. 03/14/06