Post on 01-Mar-2018
Implementing Wi-Fi at TAPMI
Submitted By: (Group – 10, PGP-1, Sec-2)
Abhisek Jain
Anvesh Ramineni Puneet Raitani Sushma Sonty
Shashank Pandey Sathvik G.V. Vinod Nair Vipin Pillai
Course - ISBT Course Instructor - Prof. Mohan Kumar
T.A. Pai Management Institute Manipal (Karnataka)
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 2
Table of Contents T O P I C Page Number
1) Introduction. 3
2) Why should TAPMI go wireless? 4
3) 802.11b and 802.11g (Wireless Standards) 5
4) Local Area Network at TAPMI (Network Diagram) 6
5) How to add Wi-Fi to an exisiting computer/laptop? 7
6) Wireless Devices for laptops and desktops 8
7) How to make existing LAN at TAPMI Wi-Fi? 10
8) How many wireless networked computers can use a single access point? 11
9) What is the range of a Wireless Network? 12
10) Roaming in a Wireless Environment. 13
11) A Pictorial Representation of Multiple Access Points. 14 12) Details of some Wireless Access Points. 15 a) Linksys Wireless-G Access Point - WAP54G b) Netgear Wireless Access Point - WG602 c) D-Link DWL-G700AP Wireless Access Point d) Netgear 256 users 108 Mbps Wireless Access Point WG302 13) Wireless Range Extenders 19 14) Wi-Fi Security Issues 20 15) A Proposal – Pilot Project : Wi-Fi at TAPMI Library 21 16) Conclusion 21
17) References 22
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 3
Implementing Wi-Fi at TAPMI
1) Introduction:
“Wi-Fi stands for Wireless Fidelity”.
In simple words, Wi-Fi is the wireless way to handle networking. It is also known
as 802.11 networking and wireless networking. The big advantage of Wi-Fi is its
simplicity. It connects computers anywhere in the organization’s premises without the
need for wires. The computers connect to the network using radio signals.
In today’s world, we find that most of the b-school campuses across India as well
as the world, are going wireless. Having a wireless campus has become one of the de-
facto standards for b-schools as well as all other premier institutions. It facilitates the use
of the I.T. resources of the institution anywhere in the campus without the need for going
to the computer lab or to a computer node connected to the network.
Wireless Networking can be compared to what cellular phones did to landline
phones. Earlier, a lot of cabling and digging was needed to install a telephone line. But
with the advent of mobile telephony, the cumbersome task of digging and laying cables,
installing cables across buildings and premises has been done away with. Similarly,
deploying a wireless network needs the right kind of hardware devices at the right places.
There is no need to have a physical cable laid out to connect to the local area network or
to any of the other I.T. resources of the institution.
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 4
2) Why should TAPMI go wireless? :
TAPMI is one of the premier b-schools of India and has been constantly ranked
among the top-15 for the past few years. It attracts one of the best talent pool in terms of
students and faculties.
Keeping the above in mind, there should be nothing stopping it from deploying
the best in I.T. infrastructure so has to enable its students and teachers to make the most
out of its I.T. facilities and databases. The most frequently used I.T. resource today is
Internet. Teachers as well as students are required to check their e-mails more than once
on a daily basis. Almost every project and assignment needs the students to refer to
resources on internet. Wi-Fi enables all this and more throughout the campus without the
need of being connected to the LAN through a wire.
Advantages of Wi-Fi:
• It can be easily deployed on the existing TAPMI LAN just by adding a
few hardware devices.
• All existing PCs and laptops can easily connect to the wireless network
just by adding a wireless device similar to a USB pen drive.
• It reduces the costs of further network deployment and expansion.
• Spaces where cables cannot be run, such as outdoor areas can host
wireless LANs.
• There are no license fees.
• Wireless LAN is low cost and easy to install.
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 5
3) 802.11b and 802.11g (Wireless Standards) :
The above words describe the two most commonly used wireless protocols or
wireless networking standards. Although there are a lot of different standards in existence
as well as under development, 802.11b and 802.11g are the most commonly used ones.
The above standards have been developed by IEEE or the Institute of Electrical
and Electronics Engineers, USA.
802.11 b:
• It operated in the 2.4GHz band
• It supports up to 11Mbps data exchange rate.
• It offers high-speed access to data at up to 300 feet from base station.
802.11 g:
• It is an extension to 802.11b.
• It also operates in the 2.4GHz band
• It supports up to 54Mbps data exchange rate.
• It is backward compatible with 802.11b. All devices supporting 802.11b
can operate on 802.11g networks at a lower speed, i.e., 11Mbps.
• It also offers high-speed access to data at up to 300 feet from base station.
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 6
4) Local Area Network at TAPMI (Network Diagram):
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 7
5) How to add Wi-Fi to an exisiting computer/laptop?
Most of the new laptops these days already come with a WiFi card built in and
support the 802.11g standard. At TAPMI, the 80% of the present batch (2005-07) has a
laptop or a desktop computer. Out of that, 75% of the laptops have got in-built wi-fi
support.
For the existing desktops at TAPMI and the older laptops with students and teachers,
it is very easy to add wireless capability. A simple USB device has to be added to these
laptops or desktops. Also, pci cards can be added to desktops and pcmcia cards can be
added to laptops.
• For a laptop, this card will normally be a PCMCIA card that will slide into
the PCMCIA slot in the laptop. Or one can buy a small external adapter
and plug it into the USB port.
• For a desktop machine, one can buy a PCI card that will get installed
inside the machine, or a small external adapter that you will connect to the
USB port.
These devices are quite cheap and affordable. Some of the listings from the online
shopping portal Ebay.in are mentioned in the next page, alongwith their prices.
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 8
6) Wireless Devices: Adding Wiress Capabitity to Laptops and Desktops :
1) Ashton USB Wireless PC / Notebook Adapter 802.11b (Rs. 1049):
2) X-Micro Wifi WLAN USB Wireless LAN adapter 802.11g (Rs. 1950):
3) SMC 54 MBps WiFi Adapter - USB 2.0 802.11g (Rs. 1999):
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 9
4) Ashton AirDash WRCB-1011R Wireless PCMCIA / Network Adapter Card 802.11b (Rs. 749):
5) X-Micro WLAN 11g PCMCIA Card (54Mbps) 802.11g (Rs. 1999):
6) Airlink Wireless WiFi PCI Adapter 54Mbps 802.11g (Rs. 1999):
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 10
7) How to make TAPMI a wi-fi campus?
There are generally the following three types of networks present in any
organization:
Type-1 Type-2 Type-3
TAPMI has type-1 LAN at present and we are discussing in this report a move to
type-3 wireless lan.
Inorder to add wireless capabilities to the I.T. infrastructure of TAPMI, just a few
hardware have to be attached to the existing LAN (Local Area Network), a diagram of
which is given in page-6, and we have a wi-fi campus ready at TAPMI. The following
two hardware devices are needed to go wireless :
1) Wireless Access Point.
2) Signal boosters to increase the range of the wireless network.
3) Repeaters – they can be used instead of signal boosters.
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 11
A wireless access pint, or base station acts like a hub, providing connectivity for
the wireless computers. It can connect (or "bridge") the wireless LAN to a wired LAN,
allowing wireless computer access to LAN resources, such as file servers or existing
Internet Connectivity.
8) How many wireless networked computers can use a single access
point?
This depends upon the manufacturer. Some hardware access points have a
recommended limit of 10, with other more expensive access points supporting up to
100 wireless connections. Using more computers than recommended will cause
performance and reliability to suffer.
Software access points (using a wifi capable computer as an access point, without
any separate hardware like an access point) may also impose user limitations, but this
depends upon the specific software, and the host computer's ability to process the
required information
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 12
9) What is the range of a Wireless Network?
Each access point has a finite range within which a wireless connection can be
maintained between the client computer and the access point. The actual distance varies
depending upon the environment; manufacturers typically state both indoor and outdoor
ranges to give a reasonable indication of reliable performance. Also it should be noted
that when operating at the limits of range the performance may drop, as the quality of
connection deteriorates and the system compensates.
Typical indoor ranges are 150-300 feet, but can be shorter if the building
construction interferes with radio transmissions. Longer ranges are possible, but
performance will degrade with distance.
Outdoor ranges are quoted up to 1000 feet, but again this depends upon the
environment.
There are ways to extend the basic operating range of Wireless Network, by
using more than a single access point or using a repeaters or wireless relay /
extension point.
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 13
10) Roaming in a Wireless Environment:
A wireless computer can "roam" from one access point to another, with the
software and hardware maintaining a steady network connection by monitoring the signal
strength from in-range access points and locking on to the one with the best quality.
Usually this is completely transparent to the user; they are not aware that a different
access point is being used from area to area.
Access points are required to have overlapping wireless areas to achieve this as
can be seen in the following diagram:
A user can move from Area 1 to Area 2 transparently. The Wireless networking hardware automatically swaps to the Access Point with the best signal.
Not all access points are capable of being configured to support roaming. Also it
is always better that access points from a single vendor should be used when
implementing roaming to ease configuration and compatibility.
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 14
11) A Pictorial Representation of Multiple Access Points :
Wireless connected computers using Multiple Access Points
A Wireless Network using Netgear WG-602 Access Point
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 15
12) Details of some Wireless Access Points:
a) Linksys Wireless-G Access Point - WAP54G (Rs. 3,899.00):
Features:
• Set up a high-speed Wireless-G (802.11g) network in your home or office. • Data rates up to 54Mbps -- 5 times faster than Wireless-B (802.11b). • Also interoperates with Wireless-B networks (at 11Mbps). • Advanced wireless security with WPA, 128-bit WEP encryption, and MAC
filtering.
Package Contents:
• Wireless-G Access Point • Detachable Antennas • Power Adapter • Setup CD with User Guide • Ethernet Network Cable • Quick Installation • Registration Card
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 16
b) Netgear Wireless Access Point - WG602 (Rs. 3,999.00):
Features:
• Netgear is the leader in unmanaged Fast Ethernet switches in both sales and port count
• Fastest growing wireless company worldwide (2003) • #1 worldwide in SPI Firewall/VPN routers • #1 in wired 10/100 PCMCIA network cards for notebook PCs in US retail • Fastest growing seller of Layers2 fixed Ethernet Switches • Extend your wireless signal by adding a WG602 in repeater mode (only available
on WG602v2 and v3). • This Netgear product comes with global warranty of 3 years and has 24 hours free
technical support call center in India.
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 17
c) D-Link DWL-G700AP Wireless Access Point (Rs. 3299):
Features:
• Up to 54Mbps
• WPA for Enhanced Wireless Security
• Quickly Add Wireless Access to Your Network
• Web-based Configuration and Management
• High-speed wireless network access for home or office
• Successfully passed through the Intel Wireless Verification Program
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 18
d) Netgear 256 users 108 Mbps Wireless Access Point WG302 (Rs. 14,999.00):
• • Supports 256 users simultaneously. • High-speed networking with IEEE 802.11g, up to 108 Mbps in turbo mode • Powerful RF management and control with AutoCell™ technology • Wi-Fi Protected Access (WPA) security support • Wireless Distribution System (WDS) supports bridging and repeater modes • Integrated IEEE 802.3af PoE • 2 detachable 5 dBi antennas • SNMP MIB I, MIB II and 802.11 MIB support • Plenum-rated • Intel® Centrino™ certified • Peak WLAN Performance with AutoCell™ • Success Story: Intel Case Study: NETGEAR® ProSafe™ Access Points
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 19
13) Wireless Range Extenders:
a) Linksys Wireless - G Range Extender (Rs. Rs. 5,499.00):
b) D-Link AirPlus DWL-800AP+ Wireless Range Extender:
c) D-Link 21dBi High Gain 2.4GHz Outdoor Directional Grid Antenna:
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 20
14) Wi-Fi Security Issues :
WiFi hotspots can be open or secure.
• If a hotspot is open, then anyone with a WiFi card can access the hotspot.
• If it is secure, then the user needs to know a WEP key to connect.
WEP stands for Wired Equivalent Privacy, and it is an encryption system for the
data that 802.11 sends through the air. WEP has two variations: 64-bit encryption (really
40-bit) and 128-bit encryption (really 104-bit). 40-bit encryption was the original
standard but was found to be easily broken. 128-bit encryption is more secure and is what
most people use if they enable WEP.
For a casual user, any hotspot that is using WEP is inaccessible unless he knows
the WEP key.
While setting up a hotspot in at TAPMI, we may want to create and use a 128-bit
WEP key to prevent the neighbors and outsiders from casually eavesdropping on our
network.
Whether at home or on the road, one needs to know the WEP key, and then enter
it into the WiFi card's software, to gain access to the network.
Security issues can thus be taken care of by using the right kind of software
configuration and managing access control to the wireless network. Hence, security
should not be an issue while implementing wi-fi at TAPMI.
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 21
15) A Proposal – Pilot Project : Wi-Fi at TAPMI Library:
As a pilot project to test wi-fi implementation at TAPMI, we may test run a pilot
project by using Linksys Wireless-G Access Point WAP54G (Rs. 3,899.00) which has
been discussed in the above pages.
• Hardware Required - Linksys Wireless-G Access Point WAP54G
• Cost of implementing this Pilot Project - (Rs. 3,899.00).
Benefits of this Pilot Project:
• Would make TAPMI Library a Wi-Fi Enabled Library
• Students and Teachers can use the I.T. resources of TAPMI on their own laptops
in the calm and serene environment of library.
• Would shoot up the rankings of TAPMI in terms of infrastructure.
16) Conclusion:
From the mentioned details and facts in the above pages, it is very clear that
implementing a wi-fi network at TAPMI is not at all a difficult task and contrary to
general notion, it doesn’t even involve exorbitant costs. The wireless hardware devices
are available at very cheap costs. In case of shift to a new campus, the same wireless
hardware can be shifted to the new campus, without any wastage of investment. Also, the
pilot project of making TAPMI Library wi-fi would help the authorities and students in
realizing the benefits of Wi-Fi. As the famous saying goes, “Seeing is believing.”
Implementing Wi-Fi @ TAPMI Group-10 (Batch 2005-07) 22
References :
1) How WiFi Works http://computer.howstuffworks.com/wireless-network1.htm 2) Set Up a Network in a Snap (PCWorld Magazine) http://www.pcworld.com/howto/article/0,aid,68763,00.asp 3) Wi-Fi Wireless Networks and Technology http://compnetworking.about.com/od/wireless/ 4) Planning, Designing & Implementing a Wi-Fi Network (PC-Quest Magazine) http://www.pcquest.com/content/depth/2005/105100101.asp 5) Top Stories - Wireless (PC-Quest Magazine) http://www.pcquest.com/content/topstories/2005/105121801.asp 6) Ebay.in - Online Shopping Portal http://www.ebay.in 7) Netgear.com - Wireless Hardware Manufacturer http://www.netgear.com 8) Dlink - Wireless Hardware Manufacturer http://www.svgopen.org/2005/images/WirelessCampusLBS_KobbenV2.pdf 9) Wi-Fi Technology : Future Market Challenges and Opportunities (An article in Journal of Computer Science) http://www.scipub.us/fulltext/jcs/jcs2113-18.pdf