Post on 15-Apr-2018
1
HVAC System Service and Design
Dan SpurgeonEngineering ManagerCab Climate Systems February 15, 2017
2
Agenda
• CAT Machine Service Updates • Quality Improvements
• Product Enhancements
• Cabin Air Quality• New Regulations & Hardware Offering
• Troubleshooting Frequent Clutch Cycling
3
Agenda
• CAT Machine Service Updates • Quality Improvements
• Product Enhancements
• Cabin Air Quality• New Regulations & Hardware Offering
• Troubleshooting Frequent Clutch Cycling
4
Service Update – Super Heavy Duty Clutches
IssueDesire for increased service interval for refrigerant compressors
ResolutionOptional service replacement compressors with super heavy-duty clutch now available
Features• Improved friction material on surfaces of pulley
and armature• Leaf springs replaced with rubber • 3 – 4X improvement in clutch service life• Available on multiple machine models
Original PartSuper
Heavy‐duty Option
Pulley Size Port Style
163‐0872394‐9671
464‐9988 133 mm O‐ring
183‐5106 501‐1179 152 mm O‐ring
320‐1291 472‐0559 133 mm Dual Seal
324‐9711 507‐3868 130 mm Dual Seal
NOTE: All models are 24 volt, Pad Mount, and have PV8 pulley
5
IssueThe existing air conditioner pressure switch may fail due to excessive vibration on certain 735C, 740C, and 745C Articulated Trucks.
ResolutionRelocate pressure switch from refrigerant compressor to high pressure discharge line.
Service LetterTEBE5358-01
Quality Update – Relocate Pressure Switch
Affected Models• 735C (S/N: LFJ1-UP; TFJ1-UP)• 740C EJECTOR (S/N: LFN1-UP; TFN1-UP)• 745C (S/N: JE81-UP; JE91-UP; LFK1-UP; TFK1-UP)
Parts Required
Qty Part Number Description1 510‐3475 Line Assembly2 327‐0282 Integral Seal1 355‐3148 Pressure Switch1 9X‐7378 O‐Ring Seal1 125‐1149 Harness As
6
Quality Update – Water Valves
IssueCooling systems on certain machines have increased coolant pressures. Existing water valves have lower life when exposed to these higher coolant pressures. ResolutionThe new 465-7630 Water Valve Gp is replacing the former 361-1289 Water Valve Gp
Affected ModelsLandfill Compactor• 826H (S/N: AWF1-UP)• 836H (S/N: BXD1-UP)Soil Compactor• 825H (S/N: AZW1-UP)Wheel Dozer• 824H (S/N: ASX1-UP)• 834H (S/N: BTX1-UP)Wheel Loader• 988H (S/N: A7A1-UP; BXY1-UP)
7
(A) 25.4 mm (1.00 inch)
1. Remove heater hose and clean the surface of the formed tube2. Reinstall the heater hose to tube with dimensions (A) from
bead to hose end.3. Inspect hose clamp for damage and replace as needed.4. Position the hose clamp to the correct distance from the hose
bead. The distance from the end of the hose clamp closest to the hose bead should be dimension (B).
5. Preferred hose clamps: 9X-2488 or 159-1503. Torque the clamp to 7.5 ± 1 N·m (66.38 ± 8.85 lb in). (B) 5 mm (0.196 inch)
Note: Use of a manual torque wrench is preferred to attain 7.5 ± 1 N∙m (66.38 ± 8.85 lb in). Do not use a pneumatic torque tool.
Quality Update – Clamping Coolant Lines
IssueCooling systems on certain machines have increased coolant pressures. Proper clamp installation is more critical than ever to prevent leaks!ResolutionFollow process shown below.
8
IssueSeal leak inside conditioner group by applying RTV sealant to the long edge seam inside the air duct. Condensate will be noticed on cab floor or inside air duct if leak is present.
Quality Update – D6T Climate System (part 1)
Resolution1. Remove AC/Heater box motor housing cover.2. Eight screws secure the cover to the AC/Heater box. One screw on
each side and three each on the top and bottom. 3. The cover slides out best with bottom edge tucked into the box and
tilted to clear the platform wall on the machine right-hand side.4. Apply a generous bead of RTV sealant to the seam of the
AC/Heater box between the drip passage and the air passage. 5. Gap is biggest on the top side of the seam nearest both corners.
Affected Models• D6T LGP (S/N: HTZ1-644 )• D6T LGP PAT (S/N: RAD1-992)• D6T XL (S/N: KMR1-590)• D6T XW (S/N: TMY1-361)• D6T XW PAT (S/N: STE1-117)
9
Quality Update – D6T Climate System (part 2)
Affected Models• D6T LGP (S/N: HTZ1-644 )• D6T LGP PAT (S/N: RAD1-992)• D6T XL (S/N: KMR1-590)• D6T XW (S/N: TMY1-361)• D6T XW PAT (S/N: STE1-117)
Resolution1. Recover refrigerant from A/C system. Record amount of oil removed
during refrigerant recovery.2. Pull vacuum on both high/low side of system for approximately 60
minutes.3. Follow directions in “Oil Amount” to determine if oil needs to be added
back into the A/C system. In most cases, oil should not need to added. 4. Charge A/C system with 1.8 kgs (4 lbs) R-134a through high pressure
line.5. Check A/C for proper operation
IssueRefrigerant and oil charge for the A/C system have been reduced. Change improves cooling performance.
Oil AmountRecovered oil < 116 ml = DO NOT ADD
Recovered oil > 116 ml (use formula below)
Recovered oil (ml) – 116 ml = add amount
10
Agenda
• CAT Machine Service Updates • Quality Improvements
• Product Enhancements
• Cabin Air Quality• New Regulations & Hardware Offering
• Troubleshooting Frequent Clutch Cycling
11
New OSHA Regulation – Air Quality
Impact to Construction Equipment
• Establishes exposure limit of 50 micrograms of respirable crystalline silica per cubic meter of air (50 μg/m3) as an 8‐hour time‐weighted average.
NOTE: 1/2 the exposure limit of old rule
• Goes into effect June 23, 2017
Rationale – Reduce adverse health effects associated with exposure to respirablecrystalline silica; COPD for example.
12
CAT Cabin Air Quality SystemUniversal Precleaner Kits
What Are YOU Breathing?
13
CAT Cabin Air Quality SystemUniversal Precleaner Kits
14
CAT Cabin Air Quality SystemFiltration Offerings
15
CAT Cabin Air Quality SystemAccessories
836K Compactor
16
Agenda
• CAT Machine Service Updates • Quality Improvements
• Product Enhancements
• Cabin Air Quality• New Regulations & Hardware Offering
• Troubleshooting Frequent Clutch Cycling
17
Operator Complaint - poor cab cooling
Pressures fluctuating due to frequent compressor cycling – High side normal Low side low
Symptoms you might see during system diagnosis
Hmm
Troubleshooting Frequent Clutch Cycling
18
Notice how rate of drop in cab temperature is slowed down once clutch cycling begins…
Clutch Cycling Impact on Cab Temperature
19
Sensor/switch malfunction
Plugged filter(s)
Plugged evaporator fins
Restriction in the refrigerant circuit
Low refrigerant charge
Excessive Clutch Cycling – service related causes
NOTE: There are also possible design related issues, but these won’t be covered today!
20
21
What might cause a dirt plugged evaporator?
How about an iced up evaporator?
Evaporator with Plugged Fins
Similar behavior as shown for plugged filter
22
This might be a little too cold!
Restricted Orifice or TXV
23
Impact of Low Refrigerant Charge
24
Faster Cycle Rate Slower Cycle Rate
Additional Note – impact of compressor speed
25
Excessive compressor cycling results in decreased evaporator capacity – hence the poor cooling complaint
Check basics first – filters, plugged coil, sensor problems, refrigerant charge
NOT ALL compressor cycling is bad – Expect to see increased frequency with mild ambient conditions and with increasing engine speed.
Summary
26
Thank You!