Post on 11-Apr-2015
description
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
HomeLibraryChallengesTutorialsEngineersBlog
Upload modelMy profileMy requestsMy likesSettingsSign out
How to make Worm Gear and its DynamicSimulation or Animation in Autodesk Inventor?Autodesk Inventor inventor autodesk tutorialtomodel ttmBy Muhammad Bilal Ghaffar on 21 Feb 12:35 9 answers 4188 views 14 comments
In this tutorial, i will show you how to model Worm Drive and its dynamic simulation or animation usingAutodesk Inventor 2012 Link to the original model is: Worm Drive
Added images
Question unclear or needs more details before answering? Comment (14)
Post comment
9 answers
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
Muhammad Bilal Ghaffar about 1 year ago
First run Autodesk Inventor.
1. Step 1
Then click New>Assembly
2. Step 2
Then save it to your working directory.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
3. Step 3
.
4. Step 4
Now in Design menu, click Worm Gear
5. Step 5
Following display menu will appear.Enter all the values shown here.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
6. Step 6
.
7. Step 7
Re-orient your model to isometric view shown below.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
8. Step 8
Right click on "Worm Gear" of side menu and turn on "Flexible" mode.
9. Step 9
Now click Assemble>Constrain
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
10. Step 10
Following display menu will appear. In place constraint menu you can see the
"Selection" 1 is active.Select "X Axis" as highlighted with green box in the following
figure.
11. Step 11
In place constraint menu you can see the "Selection" 2 is active.Now select "X Axis"
as highlighted with green box.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
12. Step 12
Then click OK
13. Step 13
In place constraint menu you can see the "Selection" 1 is active.Now select "Center
Point" as highlighted with green box.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
14. Step 14
In place constraint menu you can see the "Selection" 2 is active.Now select "Center
Point" as highlighted with green box.
15. Step 15
Then click OK
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
16. Step 16
Right click on XY Palne shown in side menu, and Turn on its "Visibility".
17. Step 17
Again open the Place Constraint menu as shown in following figure and select "XY
Plane" as highlighted with green box.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
18. Step 18
Now Selection 2 of this menu "XY Plane: of Worm Gear as shown in following figure
with highlighted green box.
19. Step 19
Click OK.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
20. Step 20
Next step is to constrain "Worm" with XY Plane of "Worm Gear". Now the tangential
constraint will be selected as shown in following figure.
21. Step 21
Select "XZ Palne" of Worm as a 1st Selection.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
22. Step 22
Now select "XY Palne" as a 2nd Selection.
23. Step 23
All Constraints are done.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
24. Step 24
Now Turn off "Visibility" of XY Plane that yoou have turend on in Step 16.
25. Step 25
Collapse all the menus in side menu.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
26. Step 26
Now click the arrow as highlighted with green box, and select "Modeling View".
27. Step 27
From Constraints menu, Right click on last constraint shown here, and select
"Drive Constraint".
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
28. Step 28
Following display menu will appear. Now Enter start value as "0 degree" and end
value as "3600 degree" to get 10 revolutions of worm.
29. Step 29
Now for advanced setting, click the << button and enter amount of value of
increment as highlighted.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
30. Step 30
Click Forward button as highlighted, and enjoy Animation or Dynamic Simulation of
Worm Drive. :-)
31. Step 31
Here is the Animation.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
32. Step 32
Don't Forget to click "It Worked" here. :-)
It worked (41)Not helpful (1)Comment (10)
1. Muhammad Bilal Ghaffar about 1 year ago
Thanks a lot eric holm :-)
2. Muhammad Bilal Ghaffar about 1 year ago
Thanks Silvio. :-)
3. 36b4c63a about 1 year ago
GIF, GIF, GIF, HEHEHEHE I LOVE GIF
4. Muhammad Bilal Ghaffar about 1 year ago
@Andreas Gkertsos.You can animate it in either way. i.e. Clockwise or Anticlockwise.You just have to exchange Start and End values as shown in Step 28.
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
5. Muhammad Bilal Ghaffar about 1 year ago
@Andreas Gkertsos. Due you can try this, gif files is now showing the real frameshere.
6. Muhammad Bilal Ghaffar about 1 year ago
In my next tutorial i will show this in Solidworks. :-)
7. Andreas Gkertsos about 1 year ago
seems like the animation is going the wrong way:PPP
8. Amos Roger about 1 year ago
How about a similar tut for solidworks dude ? :)
9. Sudhir Gill about 1 year ago
Well that's little quick :D
10. eric holm about 1 year ago
very handy
Post comment
William about 1 year ago
Great tutorial by the looks of things Muhammad and an Auto desk IV tutorial ***** x :)))))
and to make it even better a Dynamic Simulation this one I shall be trying when I get alittle spare time to my self later thank you very much Dynamic Simulation for taking the
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
time to post this one so wicked and very awesome. //Handshake
It worked (1)Not helpful (0)Comment (1)
1. Muhammad Bilal Ghaffar about 1 year ago
Thanks WILLIAM for your kind words. Try it. Dude it will hardly take 10 minutes. Youwill surely love it. :-)
Post comment
reza allahyari about 1 year ago
thank you
It worked (1)Not helpful (0)Comment (1)
1. Muhammad Bilal Ghaffar about 1 year ago
You're welcome, dude. :-)
Post comment
jaydeep n about 1 year ago
Nice Friend Thank you So Much
It worked (1)Not helpful (0)Comment (1)
1. Muhammad Bilal Ghaffar about 1 year ago
You're welcome, dude. :-)
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
Post comment
diego about 1 year ago
Good job!!!
It worked (1)Not helpful (0)Comment (1)
1. Muhammad Bilal Ghaffar about 1 year ago
Thanks diego. :-)
Post comment
Hung 9 months ago
Thank you so much
It worked (0)Not helpful (0)Add comment
Post comment
Austin Ace 5 months ago
It worked but is it important to follow the order of the constraints as given? There werefour constraints and not very intuitive as to why at first glance.
It worked (0)Not helpful (0)Add comment
Post comment
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
Roimer zambrano about 1 month ago
Muy buen material gracias...
It worked (0)Not helpful (0)Add comment
Post comment
An Ga 22 days ago
It did not work for me. The tutorial was very good but : - the spikes of the solids were entering "into" each as the animation was running. - this appears to be caused by the wrong constraint created by the wizard between theworm and the worm gear (Inventor 2013). Or I must have inverted the direction ofrotation of the worm but I cannot understand how as I followed the tutorial... Thanks anyway.
It worked (0)Not helpful (0)Add comment
Post comment
Add your answer to: "How to make Worm Gear and its DynamicSimulation or Animation in Autodesk Inventor?"
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
Add files to answer Add tutorial to answer Add a file no file selected Add a file no file selected Add a file
no file selected Add more files
1. Create tutorial
Step Picture: no file selected
2. Step Picture: no file selected
3. Step Picture: no file selected4. Add another step Cancel tutorial
Submit your answer
Follow
Tweet
Similar questions
How to make animations in Autodesk Inventor 2012? By Hardi Meybaum, 30 Sep 21:16How to use the simulate in autodesk inventor By Plinio Correa, 16 Aug 22:09How to animate gears in Inventor studio? By Manolis Theofilos, 12 Feb 09:54How to make a routed system in Autodesk Inventor? By Michael Noon, 15 Feb 18:10How to make the corresponding Autodesk Inventor By Asmo, 30 Nov 08:16
3
Like
How to make Worm Gear and its Dynamic Simulation or Animation in Autodesk Inventor? - GrabCAD
http://grabcad.com/questions/how-to-make-worm-gear-and-its-dynamic-simulation-or-animation-in-autodesk-inventor[4/11/2013 12:12:29 PM]
How to make a complete chain in Autodesk Inventor. By Alberto Cortes, 01 Jun 19:10
Similar tags
tutorialtomodel inventor autodesk ttm
Popular systems
AutoCADAutodesk InventorCreo Elements/ProCATIANXPro/Engineer WildfireSolidWorksSolid EdgeOther
I wish this page...
I wish this page would...
Send your wish
Save Cancel
HomeChallengesLibraryQ&AEngineersBlog
About usPartnersJobsBadgesFAQsChallenges overviewTwitterFacebook
© 2013 GrabCAD info@grabcad.com Terms of Service Privacy policy