Post on 02-Jun-2018
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 1/17
How to Build an EMP Generator 460,315 views
31 Editors
Edited 34 weeks ago
A favorite device of science fiction and action movie writers is the EMP generator. An EMP (or
Electro-Magnetic Pulse) has the power to knock out all electronic devices within its range. Wall
current, batteries, it doesn't matter: everything electrical just stops working. Think of the
possibilities! One pop of an EMP generator, and that car next to you—you know the one, with
the bass pumping so loud it makes your bones rattle—goes silent. Of course, so does your car.
And wristwatch. And iPhone. Oh well, back to the drawing board—which is where we come in:
we'll show you how to build a small EMP generator for fun. Be careful, though: the high voltages
involved could be dangerous. Intrigued? Read on!
Steps
1.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 2/17
1Obtain a disposable camera. It doesn't have to be anything fancy, just a cheap photo shooter
that you can pick up at any big-box store.
2.
2Slip on a pair of rubber gloves. You'll be dealing with the potential of getting a painful shock
should you accidentally touch the flash capacitor, which will carry about 300 volts when fully
charged.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 3/17
3.
3Open the case. Using the flat edge of a screwdriver, carefully pry the camera apart, being
careful not to touch the printed circuit board or any metal parts inside.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 4/17
4.
4Locate the large electrolytic capacitor on the PCB. It is commonly a black cylindrical item,
with two leads coming out of the bottom.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 5/17
5.
5Discharge the flash capacitor safely. First, check to see if it's charged. Turn on your volt
meter (if you have one), and set it to the 1000-volt scale. Place one probe on one lead of the
capacitor, and the other probe on the other lead. If there is no reading, your capacitor may
discharged. Slowly lower the scale until you get a reading.
If there's no reading, your capacitor is likely discharged already. If not...
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 6/17
6.
6Discharge the flash and remove the battery. Charge the flash by turning it on. You should
hear that familiar high-pitched whine as the capacitor charges. When the capacitor is charged, a
light will come on, or blink, or make some indication that the flash is ready.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 7/17
7.
7Wind the film up until it clicks and stops. This sets the shutter so that you can shoot.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 8/17
8.
8Click the shutter button. Don't look at the flash when you shoot! The flash should engage. As
soon as it does, remove the battery so that the capacitor does not charge again.
Use a volt meter again to check the residual charge in the capacitor. If there is, discharge it by
placing a 100-ohm resistor across the the leads. Be careful to not touch the leads with your
fingers if you're not wearing rubber gloves. You can get a nasty shock if the capacitor is still
charged!
If you use a screwdriver to discharge the capacitor, it will make a loud bang and shower sparks
and may do so several times. This is not the recommended method.
Repeat the process of checking the capacitor voltage until there is no voltage left.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 9/17
9.
9Locate the charge switch on the front of the PCB. It should make a click sound when
pressed. Peel off the tape and remove the button, then solder a toggle switch directly onto the
solder pads revealed underneath.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 10/17
10.
10Feeling adventurous? De-solder the trigger transformer and xenon flash tube from the PCB,
and store or discard them as you wish. Alternatively isolate the section of PCB with the charger
circuit and cut the rest off.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 11/17
11.
11If not, skip the above step and continue by soldering two cables onto the two capacitor
terminals. Wire one of these to a high current momentary switch. You can find those at Radio
Shack or other electronics hobby store.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 12/17
12.
12Form a load coil. Wrap 5-10 of turns of thick, insulated, stranded copper wire around a dowel
approximately 1 to 2 inches (25-50mm) in diameter. With care, slide the windings off the dowel,
and bind the coil by wrapping it with adhesive tape. You can also put an iron rod through the
center of the coil as long as it fits snug, this will intensify the effects and range.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 13/17
13.
13Attach the coil to the switch. Connect one of the leads of the load coil to the other unused
terminal on the switch, and the other lead to the free end of the cable coming from the capacitor.
You should now have a PCB with a switch to turn the charger circuit on and off and a load coil
that can be switched across the capacitor.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 14/17
14.
14Charge your EMP. Re-insert the battery. Place the load coil as close as possible to the desired
target (such as a small electric toy, cheap calculator, or anything that's not valuable). Switch the
charger on with the toggle switch, wait for the indicator to come on, then toggle the switch back
off. This is done to prevent the charger from being damaged.
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 15/17
15.
15Fire when ready. Press the momentary switch to fire your TEPG. Please note, that this will
have no effect on electronics encased in steel or aluminum—or any other metal, for that matter.
Are you an expert on folding fabric?
If so, share what you know about how to fold a scarf different ways.
Please be as detailed as possible in your explanation. We will take your detailed information,
edit it for clarity and accuracy, and incorporate it into an article that will help thousands ofpeople.
Tell us everything you know here. Remember, more detail is better.
Video
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 16/17
Warnings
Do not operate near medical equipment or computer equipment. Do not use this if you wear a
pacemaker.
May damage RFID systems or tags.
It is illegal to use this for destruction of property or disruption of services (UK).
Things You'll Need
Soldering iron
High-current momentary switch
Solder
Some general-purpose hook-up wire
Insulated thick copper cable
Small toggle switch
Disposable camera
Related wikiHows
8/11/2019 How to Build an EMP Generator
http://slidepdf.com/reader/full/how-to-build-an-emp-generator 17/17
How to
Buy Electronics Online
How to
Have Fun Without Electronics
How to
Install a Toggle Switch