Post on 07-Mar-2019
Film Wrapper Technical Bulletin
1New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Models:WHSS-1; WHSS-2;WHSC-3; WHSC-3/KD
Directory
Customer Service Bulletin............................2
Film Loading Instructions:Film Axle.........................................................3Film Roll Axle Assembly lnstuctions...........4
Electrical Diagram.........................................5
Testing............................................................6
Replacement Parts........................................7-10
Trouble Shooting...........................................11
Assembly Instructions For WHSC-3/KD.......12-13
WHSC-3
Customer Service Bulletin
2
CUSTOMER SERVICE BULLETINThe Win-Holt Film Wrappers are used to apply a thin plastic film or protective plastic covering over packaging. They consist of a film dispensing mechanism, a heated cut off rod, and a heated plate for sealing the film.
DISPENSING MECHANISMS: AXLEThe Dispensing Mechanisms of film is axle. The wrappers areavailable as table models for one or two rolls of film or a console model for three rolls mounted on axles. Models accept film roll widths up to 18”. Contact your film supplier for application information regarding film thickness and color.
HEATED CUT OFF RODThe Heated Cut-off Rod cuts the desired length of film. Thetemperature is factory preset and controlled electronically.
HOT PLATE SEALINGThe Hot plate is an aluminum casting with a bolt-on element. The operator seals the ends ofthe film on the Hot Plate. The thermo-stat which is mounted under the hot plate is adjusted by a plastic knob mounted on the right side of the hot plate. Adjustment ranges from”off to a maximum of 410°F. Temperature setting is determined by film thickness, air temperature (kitchen or cooler) and operator’s speed.
REPLACEMENT PARTS: IN-STOCK AND INTERCHANGEABLEReplacement parts are available in stock for immediate shipment.
ELECTRICAL LOADUnit is rated at 8 AMPS, 115 VOLTS
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Loading The Film Axle
3
LOADING THE FILM AXLE:
1. Loosen all Wing Nuts. Swing out right and left Bearing Blocks.
2. Lift out the Axle Assembly. Unscrew Wing End Cap, position Pin End Cap for correct fi lm width, secure with Pin and 0-Ring.
3. Position the cardboard core of the Film Roll against the taper of the Pin End Cap. Make certain thatthe fi lm will dispense from the bottom ofthe roll.
4. Replace Wing End Cap and Screw tightly.
5. Replace Axle and Film onto the Lower Bearing Blocks. Swing Upper Bearing Blocks back into place. Tighten and adjust Wing Nuts for desired fi lm tension.
MODEL: WHSS-1
MODEL: WHSS-2MODEL: WHSC-3
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Film Roll Axle Assembly
4MODEL: WHSS-1
FILM ROLL AXLE ASSEMBLY INSTRUCTIONS:
1. Install Bearing Block Assembly (A) on the left side of Base, line up holes and insert Carriage Bolts (B) and tighten using Wing Nuts (C).
2. Repeat step (1) on right side of Base.
3. Loosen all Wing Nuts (D) on Bearing Blocks on both sides to loosen top of Bearing Blocks, and then rotate top to expose Film Roll Axle Slots.
4. Install Film on Film Roll Axle (F), tighten Core Adapter Wing Nut (G), and insert in slots in the bottom of the Bearing Blocks.
5. Rotate the top of Bearing Block to cover shaft of Film Roll Axle, and tighten Wing Nuts (D) to the required tension.
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Electrical Diagram
5
HOT PLATE WITH ELEMENT ELECTRICAL DIAGRAM
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Testing
6
TESTING THE CUT-OFF ROD:
1. Disconnect the “red” CUT-OFF ROD wires from terminals 4 and 5.
2. Using an ohmmeter, measure the resistance across “red” terminal wires, reading should be approx. 195 Ohms. If there is no reading - replace CUT-OFF ROD..
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Replacement Parts
7
CORE ADAPTER WING UNIT- Compatible with other 22 1/2”wide units. Core Adapter Pin and Wing Unit sold separately.PART#WHSS-CAW
ORDER#113099
DIMENSIONS3”1.D. Roll-Threaded
SHIPWT.1 lb.
LIGHTED ROCKED SWITCH- 3-prong. Compatible with all Win-Holt wrappers.PART#WHSS-RS
ORDER#113224
DIMENSIONS1 1/4”x 1/2”
SHIPWT.1 lb.
BEARING BLOCKS- Regulates film tension. One set includes one Upper Block, one Lower Block and hardware. Compatible with other table top and console brands.
PART#WHS-BB
ORDER#113072
DIMENSIONS4”x 11 1/2”
SHIPWT.1 lb.
PLATE RETAINERS- Holds Element to Hot Plate. Made of .125 gauge aluminum.PART#WHSS-PR
ORDER#135087
DIMENSIONS4”x 11 1/2”
SHIPWT.1 lb.
WHSS-CAW
WHSS-BB
WHSS-RS
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Replacement Parts
8
ELECTRIC WIRE- High Temperature wire. Used to connect Hot Plat tothe Electrical Box.PART#WHSS-EWC
ORDER#113136
DIMENSIONSPer Foot
SHIPWT.1 lb.
CIRCUIT BOARD- E4 and E5 terminals for connecting wires as shown in schematic.PART#WHSS-CBD-A
ORDER#695885
DIMENSIONS2 1/2”x 2 1/2”
SHIPWT.1 lb.
WHSS-EWC
WHS5-CBD-A
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Replacement Parts
9
FUSE (FUS-1) AND FUSE HOLDER (FHD)- Holds 1 AMP FUSE. Compatible with other brands.PART#WHSS-FHDWHSS-FHS 1
ORDER#1131441131S2
DIMENSIONS1/4”x 1 1/4”9/32”x 1-1/4”
SHIPWT.1 lb. 1 lb.
HOT PLATE WITH HEATING ELEMENT- Seals film securely. WHSSHP is equipped with cast-in Heating Element. WHSS-HP6 which has a bolt on element is illustrated. Compatible with other brands. 600 Watts.
PART#WHSS-HP6
ORDER#113161
DIMENSIONS6”x 15”
SHIPWT.5 lb.
TEFLON COVER- For Hot Plate. Available in two sizes: Fit 6”x 15”and 8” x 15” Hot Plates. Compatible with other brands.
PART#WHSS-TC6
ORDER#113232
DIMENSIONS6”x 15”
SHIPWT.1 lb.
CUT-OFF ROD- Heats film to precise, necessary temperature.Fits other popular 22 1 /2”wide models. 105 Watts.
PART#WHSS-COR-A
ORDER#687025
DIMENSIONS7/16”x 23”
SHIPWT.2 lb.
WHSS-FHD
WHSS-TC6
WHSS-COR-A
WHSS-HP6
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Replacement Parts
10
WHSS-HP8
WHSS-CAP
WHSS-TM
WHSS-A
HEATING ELEMENT- For Hot Plate. Heats to 450°F. Fits other brands.PART#WHSS-E
ORDER#113128
DIMENSIONS9/32”x 11 1/4”
SHIPWT.1 lb.
FILM AXLE- Aluminum fi lm core axle. Compatible with other 22 1 /2”wide wrappers, table-top or console.PART#WHSS-A
ORDER#113056
DIMENSIONS3/4”x 22”
SHIPWT.2 lb.
CORE ADAPTER/PIN UNIT UNIT- Made of die-cast aluminum. Compatible with other 22 1/2”wide units. Core Pin And Wing Unit sold separately.PART#WHSS-CAP
ORDER#113081
DIMENSIONS3”1.D. Roll
SHIPWT.1 lb.
THERMOSTAT- Regulates the heat for the Hot Plate. Heats up to 450°F. Will fi t other popular 6” x 15’; 8” x 15” Hot Plates.PART#WHSS-TM
ORDER#113267
DIMENSIONSl/2”X l/2”X 2 1/4”
SHIPWT.1 lb.
THERMOSTAT KNOB- For Thermostat (Part# WHSS-TM).Compatible with other popular wrapper models.PART#WHSS-TM
ORDER#113267
DIMENSIONSl/2”X l/2”X 2 1/4”
SHIPWT.1 lb.
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Trouble Shooting
11
Apparent Problem CheckPoint Solution
Cut-off rod fails to heat properly Test the cut off rod. Use procedure described on page 6. Check Fuse.
Replace if necessary
Hot plate Fails to Heat or Overheats Visually inspect the wire andconnections under the hot plate forburning and replace if burnt.Visually inspect the lead on the heating element for burning and replace if burnt.
If burning or short circuitingdoes not show, replacethe thermostat. If burnt replace element.
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Assembly Instructions for WHSC-3/KD
12
ITEM QTY PART NUMBER1 1 Side frame2 1 Sideframe13 4 RollerAssy4 12 1/4-20 Wing Nut- UNC5 2 Spreader-Outer 20 in6 1 Spreader-Inner 20-250 in7 6 Bolt-Spreader Assy8 3 Film Axle9 3 Axle Pin End Cap
10 3 Axle Wing End Cap11 1 WHSS-3-Sani Sir12 6 Screw-PH-Figd-10-32 x 1-2513 6 Nut- Elas-Stop-10-32
PARTS LIST
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com
Assembly Instructions for WHSC-3/KD
13
Tools Required:#2 & 3 Philips Screw drivers10mm & Bmm wrench- (Socket; open end or Box)
Assembly Procedure:1. Unpack and arrange all the parts on the fl oor.2. Identify each part & its quantity with the parts list on page 12.3. Assemble Loosely (2) Item #5 & (1) Item #6 to the Side frame Item #1 with (3) Bolts Item #7 as shown.4. Assemble the (4) rollers Item #3 to the side frame in Step #3 above.5. Assemble loosely Side frame Item #2 with (3) Bolts Item #7. Note; It will require moving the Rollers & Spreaders assembled in Steps 3 & 4 individually to align with the pins & cutouts in Side frame Item #2.6. Tighten all (6) bolts Item #77. Assemble Items #9 & #10 to the Film Axle Item #8 (3) ea. in accordance with the size fi lm being used.8. Assemble the (3) Film Axle Assemblies to the side frame as shown. Loosen the wing nuts before assembly & retighten after assembly.9. Assemble the WHSS-3 sani Sealer unit Item #11 with(6) Screws & nuts Items #s 12 & 13 Tighten hardware after all screws and nuts are assembled.10. Place the assembled unit in the location of operation & adjust the leveling legs accordingly.11. Plug the unit into a 120V 15 ampere outlet & follow Operating Instructions in the product manual.
New York • Pennsylvania • Georgia • Texas • California China • India
800-444-3595 www.winholt.com