DETAIL A

SCALE 1 / 16

A

Tolerance Unless Noted Otherwise

THIS DRAWING AND THE INTELLECTUAL INFORMATION ON THIS DRAWING ARE THE

PROPERTY OF LIFTSAFE ENGINEERING & SERVICE GROUP INC. AND MAY NOT BE

REPRODUCED OR USED IN ANY MANNER WITHOUT OUR WRITTEN CONSENT

THIRD ANGLE PROJECTION

www.liftsafeinspections.com T. (519) 896-2430/1-800-977-2005,

Email: info@liftsafeinspections.com F. (519) 896-2085

SIZE

Customer & Location:

Description:

LIFTSAFE ENGINEERING & SERVICE GROUP INC.

Date:

Date:

Date:

Checked By:

Drawn By:

Designed By:

Part No.

Project:

SCALE:

SHEET 1 OF 2

DWG NO:REV

4.0

.XXX

.XX

DECIMAL PLACES

± .020

± .010

± .005

INCHES

± 0.3

± 0.1

MILLIMETRES

± 0.5

.X

Work Order No.

Materials.

Next Assembly.

ANGLE FRACTION

1/161/2°

B

N.T.S

LIFTSAFE FALL PROTECTION

AYR, ON

WIDE BODY LANDING GEAR

SERVICING STAND

SIGNATURE DATE

C.R.

G.R.

G.R.

DF071592-0410/14/2016

10/14/2016

10/14/2016

66

75 13/16

12

92 7/8 OA

43 STROKE

43 1/2 STROKE

85 3/4

58 13/16

65 5/8

91 3/4

43 1/8

139 1/8

11 3/4

FINAL ASSEMBLY

Tolerance Unless Noted Otherwise

THIS DRAWING AND THE INTELLECTUAL INFORMATION ON THIS DRAWING ARE THE

PROPERTY OF LIFTSAFE ENGINEERING & SERVICE GROUP INC. AND MAY NOT BE

REPRODUCED OR USED IN ANY MANNER WITHOUT OUR WRITTEN CONSENT

THIRD ANGLE PROJECTION

www.liftsafeinspections.com T. (519) 896-2430/1-800-977-2005,

Email: info@liftsafeinspections.com F. (519) 896-2085

SIZE

Customer & Location:

Description:

LIFTSAFE ENGINEERING & SERVICE GROUP INC.

Date:

Date:

Date:

Checked By:

Drawn By:

Designed By:

Part No.

Project:

SCALE:

SHEET 1 OF 2

DWG NO:REV

5.0

.XXX

.XX

DECIMAL PLACES

± .020

± .010

± .005

INCHES

± 0.3

± 0.1

MILLIMETRES

± 0.5

.X

Work Order No.

Materials.

Next Assembly.

ANGLE FRACTION

1/161/2°

B

N.T.S

LIFTSAFE FALL PROTECTION

AYR, ON

WIDE BODY LANDING GEAR

SERVICING STAND

GENERAL NOTES:

1) ALL STRUCTURAL STEEL SECTIONS SHALL CONFORM TO CSA G40.21-50W

2) ALL STEEL PLATE AND BAR SHALL CONFORM TO CSA G40.21-44W

3) ALL WELDING SHALL CONFORM TO CSA W59 AND BE UNDERTAKEN BY A

WELDER FULLY APPROVED BY THE CANADIAN WELDING BUREAU TO CSA W47

DIVISION

4) ALL WELDS TO BE SMOOTH AND FREE OF BURRS

5) ALL WELDS TO BE 1/4" CONTINUOUS FILLET OR 1/4" EFFECTIVE THROAT FLARE

BEVEL U.N.O.

C.R.

G.R.

G.R.

DF071592-05 GA

01/06/2017

01/06/2017

01/06/2017

FINAL ASSEMBLY

SIGNATURE DATE

INSP.

FAB.

2219 [87 in]

2445 [96 in]

2434 [96 in]

APPROXIMATE WEIGHT = 1,100 LBS (499 kg)