Post on 04-Jun-2018
8/13/2019 DeltaPoint Instruction Manual
1/2
DeltaPoint firmly in place. Call Leupold cust
to your handgun. For rifle / shotgun applica
allows fast and easy mounting on Weaver-s
Smith & WessonRevolver (For use with Smith & Wesson Classic pre-drilled
revolvers, including .500)
Remove the rear sight and retain the sight
future use if necessary. Place the insert (1
and set both pieces on the revolver as show
.210 screws through the dovetail insert and
nearest the hammer in the frame of the rev
inch pounds.
Place the DeltaPoint on the mount base so of the DeltaPoint will align with the four sho
the screw holes in the sight and mount bas
the sight with the two M4x 0.7mm screws
Mounting & Operation Instructions
Features
DiamondCoat, scratch resistant aspheric lens for maximum field ofview, brightness, and resolution.
Proprietary Intelligent Brightness Control (IBC)
Motion activated on/off illumination feature (Patent Pending)
Extremely durable, ultra light magnesium housing
Small size and weight
Unlimited eye relief For handguns, rifles and shotguns
Wide field-of-view
Blackened lens edges
Package Contents
DeltaPoint Reflex sight (1) 3V Lithium battery (CR 2032) (1) Protective cover (2) M4 x 0.7mm Torxhead screws for installing the sight on the
mounting plate
(2) 6-48x .210 Torxscrews for installing the S&W Classic base (3) TorxSet Screws (1) TorxT-5 wrench (1) TorxT-15 wrench Cross-Slot Mount
(10) Mount Bases with dovetailsMount Base 1B / Dovetail 1A - Beretta92/96 /90-TWO/Taurus PT99
Mount Base 2B / Dovetail 2A - 1911 Standard
Mount Base 3B / Dovetail 3A - GlockStandard Frame
(will not fit Large Frame .45acp, .45 GAP, 10mm models)
Mount Base 4B / Dovetail 4A - Sig SauerP226
Mount Base 5B / Dovetail 5A -SpringfieldXD
Mount Base 6B / Dovetail 6A - CZ75
Mount Base 7B / Dovetail 7A - HKHK P2000
Mount Base 8B / Dovetail 8A - Kimber Fixed/Adjustable
Mount Base 9B / Dovetail 9A - Smith & WessonM&P
Mount Base 10B / Insert 10A - Smith & WessonClassic
Operating Instructions
Specications
Magnification: 1.0x Sight window: 26mm x 19mm; 1.02 x 0.75 Elevation adjustment range: 60 MOA Windage adjustment range: 60 MOA 60 MOA per revolution of adjustment Subtension of the aiming point : 3.5 MOA Dot, 7.5 MOA inscribed Delta Operating Temperature Range: -20F to +120F (-29C to +49C) Storage Temperature Range: -40F to +160F (-40C to +71C) Power Supply: 3V with one CR 2032 Lithium battery Dimensions: (LxWxH) 1.61 x 1.18 x 1.06 (41mm x 30mm x 27mm) Weight (with battery installed): 0.6oz. (17g)
LeupoldDeltaPointReflex Sight
Operating InstructionsFor optimum performance and to prevent damage to this precision
instrument, carefully follow all instructions.
Cautions & Warnings:Check to ensure that the magazine of t he firearm has been
removed or emptied, that the action is open, and that there is
not a round in the chamber. Only after double checking the firearm, verifying
it is empty and safe, should you proceed with the installat ion of the Delta
Point. Do not look directly into the sun, light arcs or other high-intensity light
sources. Keep away from children. Adjustment lock screws are loosened at
the factory and your firearm should not be fired with the DeltaPoint att ached
until these screws are tighened to 4 inch pounds.
M4 x 0.7mm
Torx Screws
Mount Base
Pistol Frame
Dovetail
Windage
Adjustment
Adjustment
Lock Screws
Elevation
Adjustment
Intelligent
Brightness Control
Aspheric Lens LED
Start-UpThe unit operates with one commercially available 3V Lithium battery
(CR 2032) only. Insert the battery into the receptacle located on theunderside of the housing oriented so that the positive pole on the battery
label is visible. Keep the contact surface clean of dirt and corrosion,
cleaning with alcohol if necessary. If you intend to use the DeltaPoint in
a wet environment, we recommend coating the battery on all sides with
petroleum jelly or other electronics grade lubricant/ protectant to prevent
battery corrosion.
Battery InstallationRemove the two screws holding
the DeltaPoint to the base and
turn the sight upside down. Place
the Torx wrench or a screwdriver
in the notch and gently pry the
battery loose. Insert a new battery
as described earlier. The precision
pins eliminate the need for any re-adjustment.
InstallationInstallation on most handguns requires the use of one of the included
mount bases. Leupold recommends utilizing a qualified gunsmith to press/
remove the rear sight from your handgun. Once the rear sight has been
removed, the appropriate dovetail replaces the rear sight, with the part
number facing up. Some installations (Kimber / Smith & Wesson M&P)
require the use of the included set screws to be placed in the dovetail
to hold it in place and the M4 x 0.7mm Torxscrews will fasten into the
dovetail plate extension.
The corresponding mount base for your pistol is placed on top of the slide
and over the dovetail with the flat part number side facing up through the
slot in the base. Once the dovetail and mount base have been placed on
the slide, the DeltaPoint is placed on top of the base. The four holes in thebottom of the DeltaPoint will align with the four short posts on the mount
base and secure into the dovetail using the two included M4 x 0.7mm
Torxscrews ( Figure 1). Secure the screws by applying 20 inch pounds
of torque. Securing these screws creates a press-fit and will hold the
10B Mount
Base
10A Insert
6-48x .210 Screws
(Figure 1)
8/13/2019 DeltaPoint Instruction Manual
2/2
Reversible Cross-Slot MountPlace the sight on the mount base so that the screw holes in the sight and
base align, also the two short corner posts on the mount align to the holes
under the DeltaPoint. The unit may be installed with the mount base keeper
on either side. Install the two M4 x 0.7mm screws and tighten to 20 inch
pounds. Loosen the keeper on the mount. Place the mount on the rail with
the cross bolt located in the desired slot. Check to be sure all the clamping
edges are engaged. Keep a light pressure on the sight toward the muzzle
as you tighten the keeper to approximately 20 inch pounds.
Operating Procedure
Elevation and Windage Adjustment
Separate controls for the elevation and windage adjustments are found
on the top and left side of the sight. Loosen the two lock screws on the
back side of the sight counterclockwise turn each using the provided
Torx driver. Turn the D (DOWN) or R (RIGHT) screws with the provided
Torx driver. The windage adjustment
mechanism has limit stops at both ends.
Before shooting, make sure to tighten
the lock screws to 4 inch pounds.
Power On/OffThe DeltaPoint will automatically power on when movement is sensed. The
sight will switch to sleep mode when it remains still for 5 minutes.
Power-Saving ModeUnder dark conditions the LED brightness is reduced dramatically to reduce
power consumption. In addition, after the optic has been completely at rest
for 5 minutes the sight transfers to sleep mode, thus nearly eliminating all
battery drain. Upon any movement of the optic, the system powers up the
LED to the appropriate brightness in less than 1/10 of a second.
Placing the included rubber cover over the DeltaPoint forces the unit to
operate at its Lowest ambient light setting and will remain at this level
of operation until either the deltapoint is idle for 5 minutes or longer or
the cover is removed and the Deltapoint adjusts to the current ambient
conditions.
Low Battery IndicatorThe DeltaPoint has a unique feature that flashes the aiming point from
maximum to minimum brightness when low battery power is detected. The
operator will have several hours of operating time in this mode before the
sight is rendered inoperable without a battery change.
Intelligent Brightness Control
The integrated control circuit adjusts the brightness of the aiming dot /
delta according to ambient light levels. The brightness sensor on the front of
the sight senses the light level in the direction of the target and modifies the
intensity of the dot () / delta () accordingly so that it is not overpowering in
low light while remaining highly visible in bright daylight. When moving from
bright to dark conditions, the DeltaPoint will gradually decrease the intensityof the aiming dot/delta to match the dilation rate of your eye. Be careful not to
obstruct the sensor. Clean if necessary. To ensure immediate functionality,
the light-emitting diode will remain on even in complete darkness but
uses only a small amount of energy. When the optic is completely
stationary for 5 minutes the circuitry switches into sleep mode. It
immediately powers up when any movement or vibration is detected.
Water IntegrityThough the DeltaPoint is completely waterproof, extended periods of
complete immersion may result in accelerated battery depletion, possibly
requiring battery replacement. After exposure to salty or dirty water, rinse
with distilled water and dry the sight.
Leupold Full Lifetime GuaranteeLeupold warrants its products to be free from defects in materials and workmanship. Leupold
will repair or replace, at its option without charge, any product or part found to be defective under
normal use and service. Such repair or replacement shall be the purchasers sole and exclusive
remedy under this warranty. This warranty does not include normal maintenance and servicesand does not apply to any products or parts that have been subjected to modification, misuse,
negligence, accident, improper maintenance or repair by anyone other than Leupold.
The electronics in your Leupold DeltaPointReflex sight are covered by the Leupold Electronics
Warranty, and are protected from defects in materials and workmanship for two years from the
date of purchase. In event of a need for service or repair, please contact Leupold Product Service.
Note that the elevation adjustment downward stop is available only when the unit isinstalled on a mounting plate. Screwing either adjustment into a stop will lock motionof the other adjustment.
Zeroing the Point-of-Impact
The DeltaPoint windage and elevation screws move the point of impact
60 MOA (15 @ 25 yds) per revolution. Each Mark on the adjustment
screws represents about 7.5 MOA of adjustment. There is 60 MOA per
revolution and a total of 8 marks (equals 7.5 per mark). Before shooting,
make sure to tighten the lock screws on the rear of the DeltaPoint (4 inch
pounds, maximum) with the provided Torx driver.
Boresighting the DeltaPointThe use of a Leupold Zero PointBoresighter is recommended when zeroingthe DeltaPoint. Due to the low magnification of the DeltaPoint, the grid pattern
will appear relatively small. To make the boresighting process easier, Leupold
recommends placing the eye near the DeltaPoint while making windage/
elevation adjustments. As with any boresighting procedure, be sure to follow
all safety precautions prior to boresighting, and make sure the boresighter has
been removed from the the barrel prior to loading the magazine or chamber.
Warranty Limitation
There is no other express warranty. Leupold hereby dis
including but not limited to fitness for a particular purpos
incidental, consequential, or special damages arising out
performance.
Leupold Product & TeIf your Leupold product fails to perform in any way, pleas
within our Product Service department to determine if the
the product to Leupold. Many times, the problem can be
We encourage you to contact us first. Leupold Product Se
the best and most efficient manner. If we do need you to
include a note indicating your observations of the problem
as it will help us to expedite the service and return your p
With our On-line Product Service Status feature on our W
arrived, when the service began, when the service was co
obtain the UPS tracking number for follow up.
To Reach Leupold Produc
Do not adjust
this screw
Phone:7:00 a.m. - 4:30 p.m. PST M-F
1-800-LEUPOLD
or (503) 526-1400
Fax:24 hours a day, 7 days a week
(503) 352-7621
E-mail:
productspecialist@leupold.com
PaLeup
144
Bea
PoLeup
P.O.
Bea
LEUPOLD, GOLDEN RING, MARK 4, the Golden Ring desi
various other marks are registered trademarks of Leupold
corporate logos and emblems, are subject to Leupolds ri
with any product or service that is not Leupolds, or in an
Leupold, or in a manner likely to cause confusion.
Certain other trademarks used in connection with Leupol
property of their respective owners, and are used with p
CLUB and BOONE AND CROCKETT are registered tradem
NWTF is a registered trademark of the National Wild TurDEER MANAGEMENT are trademarks or registered trade
Associatio n. RMEF and ROC KY MOUNTA IN ELK FOU NDA
the Rocky Mountain Elk Foundation. ADVANTAGE TIMBE
trademarks or registered trademarks of Jordan Outdoor
MOSSY OAK BRUSH, MOSSY OAK OBSESSION, and MO
or registered trademarks of HAAS Outdoors, Inc. A.R.M.S
Research Marketing Systems, Inc. The ARD (anti-reflectio
Corp. under the name KillFlash, which is a trademark of T
We reserve the right to make design and/or material mo
Copyright 2011 Leupold & Stevens, Inc. All rights rese
Caution: B oresighting the DeltaPointVerify that the magazine of the firearm has been removed or
emptied, and that there is not a round in the chamber. Only
after double checking the firearm, verifying it is empty and safe, should you
proceed with the boresighting process. Be sure to remove the Zero Point
Boresighter from the the barrel prior to loading the magazine or chamber.
Warning: Failure to loosen adjustment lock sc rews beforemaking adjustments to elevation or windage screws will cause
sight damage. Adjustment lock screws are loosened at the
factory and must be tightened to 4 inch pounds before firing.
IlluminatedBoresighter
M4x 0.7mm Screws(Figure 3)
Leupold &StevePO Box 688 Beaverton, Oreg
www.leupold.c
1-800-LEUPOLD (5
Part #59828 Artwork
Elevation
Adjustment
Downward Stop