Tutorial on Tails Stock

Hareesha N GDept of Aeronautical Engg

Dayananda Sagar College of EnggBangalore-78

1Hareesha N Gowda, DSCE, Blore-78

PART 1: BODYSTEP 1: ProtrusionSketch on YZ plane or right plane as shown in figSymmetric protrude distance 312 mm

2Hareesha N Gowda, DSCE, Blore-78

STEP 2: CutoutSketch on XZ plane or front plane as shown in figcutout depth mm 150 mm

3Hareesha N Gowda, DSCE, Blore-78

STEP 3: CutoutSketch on YZ plane or right plane as shown in figcutout depth up to next surface

4Hareesha N Gowda, DSCE, Blore-78

STEP 4: CutoutSketch on YZ plane or right plane as shown in figcutout depth up to next surface

5Hareesha N Gowda, DSCE, Blore-78

STEP 5: CutoutSketch on XZ plane or front plane as shown in figcutout depth through all

6Hareesha N Gowda, DSCE, Blore-78

STEP 6: CutoutSketch on XZ plane or front plane as shown in figcutout depth through all

7Hareesha N Gowda, DSCE, Blore-78

STEP 7: Revolved ProtrusionSketch on XZ plane or front plane as shown in figrevolve protrusion angle 3600

8Hareesha N Gowda, DSCE, Blore-78

STEP 8: ProtrusionSketch on XY plane or Top plane as shown in figSymmetric protrusion distance 70 mm

9Hareesha N Gowda, DSCE, Blore-78

STEP 9: CutoutSketch on YZ plane or front plane as shown in figcutout depth 70 mm

10Hareesha N Gowda, DSCE, Blore-78

STEP 10: HoleHole 1 of diameter 38 mm through allHole 2 of diameter 22 mm depth 35 mmHole 3 of diameter 8 mm, 4 holes depth 15 mm

11Hareesha N Gowda, DSCE, Blore-78

PART 3:BARRELSketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o

cutout dimension 4.5 x 3 mm length 245 mm

12Hareesha N Gowda, DSCE, Blore-78

PART 4:SCREW SPINDLESketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o

cut out 4.5 x2.25 and 28 mm length

13Hareesha N Gowda, DSCE, Blore-78

PART13 handleSketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o

sketch on XY or top plane as shownSymmetric protrusion distance 40 mm

14Hareesha N Gowda, DSCE, Blore-78

PART19 CENTRESketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o

15Hareesha N Gowda, DSCE, Blore-78

PART 8 HAND WHEELStep 1:Sketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o

16Hareesha N Gowda, DSCE, Blore-78

PART 8 HAND WHEELStep 2:Sketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o

17Hareesha N Gowda, DSCE, Blore-78

PART 8 HAND WHEELStep 3:Sketch on YZ plane or right plane as shown in figUse lofted protrusion

18Hareesha N Gowda, DSCE, Blore-78

PART 8 HAND WHEELStep 4:circular pattern according to the requirement

19Hareesha N Gowda, DSCE, Blore-78