Assembly of Tail stock
-
Upload
hareesha-n-gowda-dayananda-sagar-college-of-engg-bangalore -
Category
Education
-
view
17.168 -
download
0
Transcript of Assembly of Tail stock
Tutorial on Tails Stock
Hareesha N GDept of Aeronautical Engg
Dayananda Sagar College of EnggBangalore-78
1Hareesha N Gowda, DSCE, Blore-78
PART 1: BODYSTEP 1: ProtrusionSketch on YZ plane or right plane as shown in figSymmetric protrude distance 312 mm
2Hareesha N Gowda, DSCE, Blore-78
STEP 2: CutoutSketch on XZ plane or front plane as shown in figcutout depth mm 150 mm
3Hareesha N Gowda, DSCE, Blore-78
STEP 3: CutoutSketch on YZ plane or right plane as shown in figcutout depth up to next surface
4Hareesha N Gowda, DSCE, Blore-78
STEP 4: CutoutSketch on YZ plane or right plane as shown in figcutout depth up to next surface
5Hareesha N Gowda, DSCE, Blore-78
STEP 5: CutoutSketch on XZ plane or front plane as shown in figcutout depth through all
6Hareesha N Gowda, DSCE, Blore-78
STEP 6: CutoutSketch on XZ plane or front plane as shown in figcutout depth through all
7Hareesha N Gowda, DSCE, Blore-78
STEP 7: Revolved ProtrusionSketch on XZ plane or front plane as shown in figrevolve protrusion angle 3600
8Hareesha N Gowda, DSCE, Blore-78
STEP 8: ProtrusionSketch on XY plane or Top plane as shown in figSymmetric protrusion distance 70 mm
9Hareesha N Gowda, DSCE, Blore-78
STEP 9: CutoutSketch on YZ plane or front plane as shown in figcutout depth 70 mm
10Hareesha N Gowda, DSCE, Blore-78
STEP 10: HoleHole 1 of diameter 38 mm through allHole 2 of diameter 22 mm depth 35 mmHole 3 of diameter 8 mm, 4 holes depth 15 mm
11Hareesha N Gowda, DSCE, Blore-78
PART 3:BARRELSketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o
cutout dimension 4.5 x 3 mm length 245 mm
12Hareesha N Gowda, DSCE, Blore-78
PART 4:SCREW SPINDLESketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o
cut out 4.5 x2.25 and 28 mm length
13Hareesha N Gowda, DSCE, Blore-78
PART13 handleSketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o
sketch on XY or top plane as shownSymmetric protrusion distance 40 mm
14Hareesha N Gowda, DSCE, Blore-78
PART19 CENTRESketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o
15Hareesha N Gowda, DSCE, Blore-78
PART 8 HAND WHEELStep 1:Sketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o
16Hareesha N Gowda, DSCE, Blore-78
PART 8 HAND WHEELStep 2:Sketch on XZ plane or front plane as shown in figUse revolve protrusion angle 360o
17Hareesha N Gowda, DSCE, Blore-78
PART 8 HAND WHEELStep 3:Sketch on YZ plane or right plane as shown in figUse lofted protrusion
18Hareesha N Gowda, DSCE, Blore-78
PART 8 HAND WHEELStep 4:circular pattern according to the requirement
19Hareesha N Gowda, DSCE, Blore-78