Ford 2.0L ZetecPerformance Engine Packages
OMEXwww.omextechnology.co.uk
Brochure v1.11 12/11/10
Road Track Race Ltd,42 Mount Street,New Basford,Nottingham,NG7 7HX
Tel: 0115 9780677Fax: 0115 8377973
www.roadtrackrace.com
Ford Zetec 2.0L (Focus Blacktop) Engine Packages
Selecting your engine
Our range of OmexPower engines has been developed to be engine package solutions that are truly ’turn key’. We have developed acoherent range of very high quality, fully tested engine packages with varying power outputs to suit your requirements and budget. All ourengine packages are built on brand new engines. The engines are all built at Omex, mounted on a special jig and hot run. This meansthat the cams are run in, the throttle bodies (where applicable) are balanced, the idle speed is set and the emissions are checked for IVAand MOT compliance. The engines are supplied with the multi championship winning Omex 600 Series ECU and a fully assembled wiringloom manufactured in Raychem DR25 heatshrink as standard. To ensure absolute peace of mind the engine is tested with the actual loomand ECU that are shipped with your engine. As the ECUs are all pre-calibrated there is no need to run any OmexPower engine on a rollingroad or dyno. Simply fit to your car, connect 5 wires (details are of course supplied) and start the engine!
The OmexPower range of Ford Zetec engines covers power outputs of 150 to 200 bhp (normally aspirated) and 220bhp (supercharged).The normally aspirated engines are available in both inline (to suit front engine rear wheel drive) and transverse (to suit mid enginetransverse applications) versions. The supercharged engine is currently available as an inline engine only. The inline engines use thesuperb RaceLine lowline fully baffled sump (do not confuse this with cheap inferior copies that are available) whilst the transverse enginesuse the original Ford aluminium and steel sump.
There are a wide range of mechanical options and upgrades available to suit your requirements, such as 3 different throttle body lengthsand 2 manifolds (throttle body engines only), different clutches and flywheels, side water rails, a choice of linkages, uprated valve springsetc. The available options for each engine specification are detailed at the end of each section. In addition there are several electronicoptions available, such as full throttle gearshift, shift lights and more, again detailed at the end of each engine. If you would like adviceabout which specification fits your vehicle best then please give us a call.
If you would like to see any of our engines, we generally have all specifications available for viewing. In addition we have mostspecifications available in demonstration vehicles. Most of these regularly attend track days and you would be most welcome if you wouldlike a demonstration on track.
220
bhp
Zete
c E
ngin
e
-Rotrex centrifugal supercharged
-220 bhp
-Inline installation only
-High torque ouput
170-
200
bhp
Zete
c E
ngin
e
-Multiple throttle body inlet for instant
throttle response
-170 and 200 bhp versions
-Transverse and inline installations
-Increased power band
-Plenum inlet
-150 bhp
-Transverse and inline installations
-Economical engine package with scope for later
upgrades to other engine packages
150
bhp
Zete
c E
ngin
e
Engine shown is ZE20SC010
Engine shown is ZE20F020
Engine shown is ZE20F010
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 2
150
bhp
Zete
c E
ngin
e
Plenum Inlet Zetec Engine - 150 bhp
How much power will my engine make?The power and torque graph shows the results obtained from an engine in a Westfield SEiW, using a Westfield 4-1 exhaust manifold,catalytic convertor, and silencer system. These results are from testing on Omex’s Superflow rolling road.
Engine Power Graphs
PowerTorque
100
125
150
175
2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000RPM
50
75
BH
P /
Torq
ue
Zetec Blacktop 2.0 150 bhp Engine Power Graph
ZE20F010
This superb value entry level engine package sacrifices nothing in the way of quality or design, utilising the same high specification billetalloy bracketry and high quality components. Available in both inline (front engine rear wheel drive) and transverse (mid engine)specifications, it uses the standard Ford inlet plenum and throttle body. An idle air bypass valve controlled directly from the multichampionship winning Omex 600 Series ECU provides perfect driveability whatever the temperature. The inline version is fitted with theexcellent RaceLine lowline alloy sump to allow maximum ground clearance whilst the transverse specification uses the Ford alloy and steelsump assembly. Both versions are available with a wide range of upgrades and options to suit your specific requirements.
150 BHP Engine ZE20F010 (inline)150 BHP Engine ZE20F010T (transverse)
Engine--
Engine SpecificationNew Focus Zetec 2.0L Blacktop EngineReady Mapped 600 Series ECURace Spec Ready Built Wiring HarnessLowline Baffled Sump (inline only)Flywheel and ClutchAlternator with Billet Aluminium Brackets & BeltStandard Exhaust Manifold (no cost option)Inlet Manifold with Single Throttle BodyFuel RailFuel Pressure RegulatorThrottle Position SensorAir Temperature SensorCoolant Temperature SensorCrank Position SensorInjectorsIgnition Coil Pack and LeadsOil FilterGaskets
Engine shown is ZE20F010
Inline Specification
Engine shown is ZE20F010T
Transverse Specification
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 3
150
bhp
Zete
c E
ngin
eSump
Transverse specification engines are supplied with the standard sump as this is designed for transverse mounting. Inline engines havecornering forces in a different direction on the engine and so the inline specification engines are fitted with a new low line groundclearance sump with internal baffling designed to keep the oil on the pickup. This sump has been tested in vehicles up to single seaterswith slicks and wings generating very high cornering forces.
The standard inlet is used on this engine specification. This gives the option of a remote air filter location so keeping noise to a minimumin the passenger compartment. An ECU controlled idle control valve is used to maintain idle when the engine is cold and heavily loadedby electrical devices such as heated screens, lights etc.
Omex’s multi-championship winning 600 Series ECU controls the fuel injection, Ford distributorless ignition coil pack, and optionally,many other functions around the vehicle. The ECU is connected to the hardware with a complete, DR25 Raychem heatshrunk racespecification wiring harness, which is fully tagged and with the correct connections made for your Zetec engine, ensuring easy clip-onfitment. The ECU, wiring harness and sensors are kept with each engine build throughout assembly and testing work, ensuring that theengine package you receive has been tested as a whole package.
Electronics
What comes with the engine?
Inlet System
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 4
150
bhp
Zete
c E
ngin
e
Air and coolant temperaturesensors are supplied and fitted.
Bosch injectors are used givingexcellent spray patterns tooptimise power outputs andreduce emissions.
Flywheel and Clutch
A standard flywheel and clutch is included with the engineto suit type 9, MT75 and MTX75 gearboxes. Upgrades andsetups for other gearboxes are available, such as IB5gearbox (transverse).
Ignition
DIS coil pack, ignition leads, and spark plugs are all included
Lightweight hard-anodised billet aluminium brackets are used to mount the high output 2 wire alternator and associated belt pulleys.Transverse and inline specification engines have different belt runs to allow the use of the relevant engine mount positions. Inline specalternator setup shown, the transverse spec is similar.
Alternator
The engine utilises a fuel pressureregulator built into the fuel rail.
Fuel Pressure Regulator
Injectors Temperature Sensors
Crank and throttle positionsensors are supplied and fittedto all engines.
Crank & Throttle Sensors
A good 4-1 exhaust manifold shouldshould be used to achieve the statedpower outputs of the engines. A standardexhaust manifold gasket is included withthe engine. If required the standard FordFocus exhaust manifold can be suppliedwith the engine without additional chargebut should only be used if a reduction inpower output is acceptable.
Exhaust Manifold
All gaskets and an oil filter areincluded and fitted.
Gaskets & Oil Filter
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 5
150
bhp
Zete
c E
ngin
eAll dimensions are approximate, if you need any other dimensions please ask.
Engine Dimensions (Inline Version)
-Ignition coil pack can be removed and mounted remotely-Exhaust manifold can be replaced with customers own exhaust manifold-Optional side water rail reduces the size of the water housing (see options list)-Oil filter can be changed for a shorter filter
490mm
550m
m
580m
m
Front ofpulleys
Rear ofblock
Rear ofcoil
125mm
Bot
tom
of
sum
pTo
p of
oil
cap
& c
am c
over
125mm
490mm
565mm
Rear ofblock
Rear ofcoil
Front ofpulleys
Back ofWater housing
Cra
nkce
ntre
line
200m
m32
0mm
270mm
455mm
520mm
Cra
nkce
ntre
line
Bot
tom
of
sum
p150m
m43
0mm
Top
ofca
m c
over
Side ofinlet manifold
Side ofexhaust manifold
& water pump
Top
ofin
let m
anifo
ldB
otto
m o
fin
let m
anifo
ld
320m
m60 m
m50 m
m
Sid
e of
inle
t man
ifold
Sid
e of
exha
ust m
anifo
ld&
wat
er p
ump
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 6
150
bhp
Zete
c E
ngin
eAll dimensions are approximate, if you need any other dimensions please ask.
Engine Dimensions (Transverse Version)
Engine pictures shown with large flywheel suitable for MTX75 gearboxes, not suitable for IB5 gearboxes. See options for alternativeflywheels and clutch assemblies.
-Ignition coil pack can be removed and mounted remotely-Exhaust manifold can be replaced with customers own exhaust manifold-Optional side water rail reduces the size of the water housing (see options list)-Oil filter can be changed for a shorter filter
490mm
600m
m
630m
m
Front ofpulleys
Rear ofblock
Rear ofcoil
125mm
Bot
tom
of
sum
pTo
p of
oil
cap
& c
am c
over
125mm
490mm
565mm
Rear ofblock
Rear ofcoil
Front ofpulleys
Back ofWater housing
Cra
nkce
ntre
line
200m
m32
0mm
200mm
420mm
520mmSide of
inlet manifoldSide of
exhaust manifold& water pump
Top
ofin
let m
anifo
ldB
otto
m o
fin
let m
anifo
ld
320m
m60 m
m50 m
m
Cra
nkce
ntre
line
Bot
tom
of
sum
p
200m
m43
0mm
Top
ofca
m c
over
Sid
e of
exha
ust m
anifo
ld&
wat
er p
ump
Sid
e of
inle
t man
ifold
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 7
150
bhp
Zete
c E
ngin
e
Starter Motor – For inline specification engines there are two options available, standard remanufactured and new high power startermotors. For transverse specification engines the standard Ford start motor will have to be used.Bellhousing – A cast aluminium bell housing is available to suit the Ford Sierra type 9 (short input shaft) gearbox.Flywheel and Clutch - A standard flywheel and clutch is included with the engine to suit type 9, MT75 and MTX75 gearboxes. A cost optionis available for a different flywheel / clutch assembly for users of the IB5 gearbox.
Bellhousing for type 9 gearboxStarter Motor Flywheel and Clutch
Mechanical Fitting Options and Upgrades
Options and Upgrades
Engine Internals Options and Upgrades
Side Water Rail – for inline applications where the thermostat housing would hit the bulkhead, the ‘side water rail’ allows the removal ofthe thermostat housing, so allowing the engine to be mounted further back. If a water header tank cannot be fitted to the vehicle, a pressurecap is available for the ‘side water rail’ to remove the need for the header tank. Note that this cannot be used with a standard exhaustmanifold, only with an four branch manifold.To allow extra clearance the ignition coil pack and bracket can be unbolted and mountedremotely.
Side water rail Side water rail Standard Water Housing
For engines that are expected to spend a lot of time at high engine speeds, such as those which are intended for competition use orextended trackday use, extra safety can be inbuilt through the upgrade to ARP big-end bolts and uprated valve springs.
Uprated ARP Big-end bolts Uprated Valve Springs
Ignition coil pack can be remotely mounted
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 8
150
bhp
Zete
c E
ngin
eWith optional extra parts the Omex 600 ECU is capable of much more than simply running the engine;
Shift lights - a visual warning for the optimum rpm gearshift. Normally a high intensity 10mm red LED is used, but other sizes and coloursare available.Full throttle gearshift - gearshifts without lifting off the throttle. In the case of sequential gearboxes, even without using the clutch.Sequential gearboxes often have a switch inbuilt for input to the ECU, and those using a ‘normal’ gearbox can use an Omex clutch switch,signalling an ignition retard that temporarily reduces engine power output.Launch control - consistent fast starts. A button on the steering wheel that gives a temporary lower rev limit holding the engine steady onthe startline.Radiator fan control - reduce the number of joins and sensors in the cooling system, and have full programmability of the ON / OFFtemperatures for the radiator fan. An additional relay is required for this control.Barometric air pressure correction – If you are using the engine with large altitude changes (such as in the mountainous areas), thenair pressure changes due to the altitude changes will affect the amount of fuel required. An upgrade to fit an air pressure sensor toautomatically make these changes is available.Emissions control - The engine simply needs a narrowband lambda sensor and an effective catalytic convertor and it will then pass UKMOT and IVA emissions tests with ease. Omex can provide a lambda sensor and boss to weld to the exhaust. A lambda sensor is notrequired to make the engine run, so if you have a vehicle that does not need to pass emissions tests, then a lambda sensor is optional.Throttle position sensor – For use in extreme conditions such as off-road rallying, a contactless throttle position sensor can be used togive improved reliability due to improved protection against water and dust.
Shift light (10mm LED) Full throttle gearshift(clutch switch)
Launch control (button) Radiator fan control(Relay and base)
Barometric pressure sensorand harness upgrade
Lambda sensor Lambda sensor boss Throttle position sensorupgrade
Electronic Control Options and Upgrades
Why choose Omex Products?
The difference between winning and losing is very small. In hillclimbing and sprinting it can regularly be 0.05 secs, in circuit racing a halfcars length, in rallying one corner...........
So what makes Omex products win so many events and championships? Simple, attention to DETAIL.
The very basics of how the ECU works makes a big difference. How it calculates when an ignition spark is going to be placed, when it’scalculated, how engine acceleration is taken into account, and so ultimately how accurately that spark is placed, are things that you do notthink about when looking at ECUs. Here at Omex we do because those details that are often taken for granted are the difference betweenone ECU system and another, the difference between winning and losing... The detailed approach to design of the basics by our team oftop software and hardware design engineers, responsible for race wins throughout all forms of motorsport at the very highest levels, meansyou do not need to think about these details because we do. Features lists don’t win races; it’s how these features work that wins races.Other ECUs may have similar features lists, but how an Omex works makes all the difference. Naturally, Omex ECUs have all of thefeatures you would expect from a top level ECU.
Winning Championships is a combination of performance and reliability. Reliability is found in the details of the way the ECU is designedand built. All Omex ECUs are robot assembled in the UK on an ISO9001:2000 approved assembly line, ensuring a consistent, high qualitybuild. They are all then thoroughly tested, twice, before leaving Omex. A well running system is a combination of ECU and many othercomponents. It is important that all components in the system continue to work in order for the ECU to be able to perform, and so Omexsource all other components such as sensors and injectors only from highly respected manufacturers.
Of course, before you can even think about winning races and championships, you need to get to the race! Omex employ only degreequalified engineers to ensure that whenever you contact us you get only the very best advice, right from specification of the best parts foryour application, through to advice during installation, and finally, getting your engine running to its maximum potential.
And should something go wrong at any time during your ownership of your Omex ECU, the same team of technicians is available just atelephone call or mouse click away with free advice to help you through.
All these details have helped countless others win races and championships. Maybe you will be next…
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 9
150
bhp
Zete
c E
ngin
e
E&OE. Price list (Retail) valid from 22/10/2010 until further notice. [email protected]%
Engine shown is ZE20F010
Options and Upgrades
Lightweight steel flywheels (various options available)
Side water rail (complete assembly - fitted)
Starter motor - remanufactured (inline only)Starter motor - high torque (inline only)
Bellhousing (alloy, to fit Ford type 9 gearbox)
Uprated ARP big-end bolts - fitted to inline specification engineUprated ARP big-end bolts - fitted to transverse specification engineUprated valve springs - fitted to 150 bhp engine
Shift light (10mm LED - red) - inc mounting bezel and cablesShift light (5mm LED - red) - inc mounting bezel and cablesFull throttle gearshift clutch switch - inc cablesLaunch control button - inc cablesRadiator fan control relay and baseBarometric pressure sensor upgrade (inc harness upgrade)Lambda (oxygen) sensorLambda sensor boss
Kit Part Number
OMEM6003OMEM6004OMEM6010OMEM6011OMEM6100OMEM2100(U) + OMEM1520(U)OMEM2301OMEM2351
Retail
Ask
£244.63
£85.00£185.00
£205.75
£150.00£200.00£400.00
£7.80£7.80£5.00£8.00£4.00£126.00£55.00£5.00
Inc VAT
Ask
£287.44
£99.88£217.38
£241.76
£176.25£235.00£470.00
£9.17£9.17£5.88£9.40£4.70£148.05£64.63£5.88
--
Inline 150 BHP Engine Standard Inlet SystemTransverse 150 BHP Engine Standard Inlet System
ZE20F010ZE20F010T
£2995.00£2395.00
£3519.13£2814.13
--
--
Optional parts are standalone extra parts and can be added to your kit at any time. Upgrade parts, designated by a ‘(U)’ in the partnumber, are upgrade parts in the kit and so are only available at the above prices at the time of kit purchase. They are available at anytime, but at the full price of the part.
-
-
--
-
---
--------
-
-
--
-
---
--------
-
-
--
-
---
--------
Price List: ZE20F010 (150 bhp) Standard Inlet System
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 10
170-
200
bhp
Zete
c E
ngin
e
How much power will my engine make?The power and torque graph shows the results obtained from an 170 bhp engine in a Westfield SEiW, using a Westfield 4-1 exhaustmanifold, catalytic convertor, and silencer system. The 200 bhp engine in a Caterham, using a Raceline 4-1 exhaust manifold.
Engine Power Graphs
Multiple Throttle Body Inlet Zetec Engine - 170 / 200 bhp
A significant step up from the 150bhp specification in terms of performance, the superb 170bhp specification engine offers a far greaterperformance gain than the 20bhp increase would suggest. Available in both inline (front engine rear wheel drive) and transverse (midengined) specifications, our most popular specification utilises individual throttle butterflies for each cylinder which gives unrestrictedairflow to each cylinder and hence a higher power output. In addition, the ability to produce more power and torque at the higher end ofthe rev range means that the performance gain is much greater than may initially be expected. Also the sound of throttle bodies cannotbe beaten. This engine is ideal for those building a kit car that may be used on track, but which maintains perfect tractability and mannersfor use on the road. The 200bhp specification adds further to this with a beautifully gas flowed cylinder head and bespoke cams, but alsomaintains its perfect road manners whilst offering invigorating performance. Both are available with a wide range of options andupgrades to suit your car perfectly. The inline version is fitted with the excellent RaceLine lowline alloy sump to allow maximum groundclearance whilst the transverse specification uses the Ford alloy and steel sump assembly.
Engine shown is ZE20F020with long throttle bodies
Inline Specification
Engine shown is ZE20F020Twith long throttle bodies
Transverse Specification
PowerTorque
100
125
150
175
2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000RPM
50
75
BH
P /
Torq
ue
Zetec Blacktop 170 bhp Engine Kit Power Graph
ZE20F020
PowerTorque
100
125
150
175
2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000RPM
50
75
BH
P /
Torq
ue
Zetec Blacktop 2.0 200 bhp Engine Power Graph
ZE20F040200
225
200
170 BHP Engine ZE20F020 (inline)170 BHP Engine ZE20F020T (transverse)
200 BHP Engine ZE20F040 (inline)200 BHP Engine ZE20F040T (transverse)
Engine--
--
Engine SpecificationNew Focus Zetec 2.0L Blacktop EngineReady Mapped 600 Series ECURace Spec Ready Built Wiring HarnessLowline Baffled Sump (inline only)Gas Flowed Head & Inlet Manifold (200 bhp only)Uprated Camshaft (200 bhp engine only)Flywheel and ClutchAlternator with Billet Aluminium Brackets & BeltThrottle BodiesInlet ManifoldFuel Rail
Air HornsFuel Pressure RegulatorThrottle Position SensorAir Temperature SensorCoolant Temperature SensorCrank Position SensorInjectorsIgnition Coil Pack and LeadsOil FilterGaskets
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 11
170-
200
bhp
Zete
c E
ngin
e
Electronics
What comes with the engines?
Sump
Inline engines have cornering forces in a different direction on the engine to standard and so the inline specification engines are fittedwith a new sump with internal baffling designed to keep the oil on the pickup. This sump has been tested in vehicles up to single seaterwith slicks and wings generating very high cornering forces. Transverse specification engines are supplied with the standard enginesump.
Proven, reliable, Jenvey throttle bodies are used on these specification engines. Individual throttle plates give the air an unrestrictedroute to the engine giving maximum power. There are three options of throttle body lengths and two manifold designs to suit all applications.
Inlet System
Omex’s multi-championship winning 600 Series ECU controls the fuel injection, standard Ford distributorless ignition coil pack, andoptionally, many other functions around the vehicle. The ECU is connected to the hardware with a complete, DR25 Raychemheatshrunk, race specification wiring harness, which is fully tagged and with the correct connections made for your Zetec engine,ensuring easy clip-on fitment. The ECU, wiring harness and sensors are kept with each engine build throughout assembly and testingwork, ensuring that the engine package you receive has been tested as a whole package.
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 12
170-
200
bhp
Zete
c E
ngin
e
The coolant temperature sensoris supplied and fitted. The Airtemperature sensor is suppliedfor mounting in engine bay or airfilter.
Flywheel and Clutch Ignition
DIS coil pack, ignition leads, and spark plugs are all included
Alternator
Injectors Temperature Sensors
Crank and throttle positionsensors are supplied and fittedto all engines.
Crank & Throttle Sensors
Lightweight hard-anodised billet aluminium brackets are used to mount the high output 2 wire alternator and associated belt pulleys.Transverse and inline specification engines have different belt runs to allow the use of the relevant engine mount positions. Inline specalternator setup shown, the transverse spec is similar.
A standard flywheel and clutch is included with the engineto suit type 9, MT75 and MTX75 gearboxes. Upgrades andsetups for other gearboxes are available, such as IB5gearbox (transverse).
Cams
Standard cams are used in the 170 BHP engine. Upratedcams are used in the 200 BHP engine.
Cylinder Head
A standard cylinder head is used on the 170BHP engine.The 200 bhp engine has a superb ported and gas-flowedhead with the inlet manifold port-matched for improved airflow.
Bosch injectors are used givingexcellent spray patterns tooptimise power outputs andreduce emissions.
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 13
170-
200
bhp
Zete
c E
ngin
eLong Throttle Body Set
231mm
24o
Long set with upgrade inlet manifold
All above dimensions and angles are approximate
Long set with standard inlet manifold
218mm
5o
3 different throttle body lengths and 2 different inlet manifolds exist toenable you to get the perfect fit in your chassis.
A minimum of 20mm should be allowed between the end of the air hornand the air filter material. Also allow space for the movement of the engine.
The long kit should be used where possible as it is easier to fit and will givea better torque curve than the short kit in most cases.
The standard manifold curves to put the throttle bodies level when fitted toa level engine.
Lengths between the two kits are possible by changing airhorn length onrequest.
An optional upgrade manifold faces the throttle bodies slightly upwards inline with the port angle to allow maximum airflow.
Inlet Length Choice
Fuel pressure is regulated by aconstant pressure billet aluminiumhoused regulator.
Fuel Pressure Regulator
An insulating gasket is usedon the inlet manifold to re-duce heat conduction to theinlet and so lower inlet airtemperatures for increasedpower.
Gaskets
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 14
170-
200
bhp
Zete
c E
ngin
e
Short Throttle Body Set
131mm
Short set with standard inlet manifold
5o
144mm
24o
Short set with upgrade inlet manifold
All above dimensions and angles are approximate
Medium Throttle Body Set
204mm
24o
Medium set with upgrade inlet manifold
191mm
5o
Medium set with standard inlet manifold
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 15
170-
200
bhp
Zete
c E
ngin
e
All dimensions are approximate, if you need any other dimensions please ask.
Engine Dimensions (Inline Version)
490mm
550m
m
580m
m
Front ofpulleys
Rear ofblock
Rear ofcoil
125mm
Bot
tom
of
sum
pTo
p of
oil
cap
& c
am c
over
125mm
490mm
565mm
Rear ofblock
Rear ofcoil
Front ofpulleys
Back ofWater housing
Cra
nkce
ntre
line
200m
m31
2mm
270mm
455mm
520mmEnd of
Throttle bodies
Top
ofth
rottl
ebo
dies
Bot
tom
of
thro
ttle
bodi
es 110m
m45 m
m
Cra
nkce
ntre
line
Bot
tom
of
sum
p150m
m43
0mm
Top
ofca
m c
over
Side ofdip stick
& water pump
Sid
e of
dip
stic
k&
wat
er p
ump
End
of
Thro
ttle
bodi
es
275m
m
-Ignition coil pack can be removed and mounted remotely-Exhaust manifold can be replaced with customers own exhaust manifold-Optional side water rail reduces the size of the water housing (see options list)-Oil filter can be changed for a shorter filter
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 16
170-
200
bhp
Zete
c E
ngin
e
All dimensions are approximate if you need any other dimensions please ask.
Engine Dimensions (Transverse Version)
Engine pictures shown with large flywheel suitable for MTX75 gearboxes, not suitable for IB5 gearboxes. See options for alternativeflywheels and clutch assemblies.
-Ignition coil pack can be removed and mounted remotely-Exhaust manifold can be replaced with customers own exhaust manifold-Optional side water rail reduces the size of the water housing (see options list)-Oil filter can be changed for a shorter filter
490mm
600m
m
630m
m
Front ofpulleys
Rear ofblock
Rear ofcoil
125mm
Bot
tom
of
sum
pTo
p of
oil
cap
& c
am c
over
200mm
408mm
512mmSide of
inlet manifoldSide ofdip stick
& water pump
Cra
nkce
ntre
line
Bot
tom
of
sum
p
200m
m43
0mm
Top
ofca
m c
over
125mm
490mm
565mm
Rear ofblock
Rear ofcoil
Front ofpulleys
Back ofWater housing
Cra
nkce
ntre
line
200m
m31
2mm
Sid
e of
dip
stic
k&
wat
er p
ump
End
of
Thro
ttle
bodi
es
Top
ofth
rottl
ebo
dies
Bot
tom
of
thro
ttle
bodi
es 110m
m45 m
m27
5mm
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 17
170-
200
bhp
Zete
c E
ngin
e
Options and Upgrades
OMEX POWER
Air filter socksAir filter and back plate
Throttle linkage – single and twin cable versions are available. They are supplied pre-built onto the throttle bodies assembly and may beadjusted to give the best throttle action. They can be fitted above or below the throttle bodies with the cable feeding to the left or right,please specify when ordering.
Air filtration – the throttle bodies will accept DCOE / DHLA pattern backplate air filters (use with long throttle bodies only). ‘Sock’ filterscan be used where space is tight or with the medium or short throttle bodies.
Single cable throttle linkage kit(top mounting)
Twin cable throttle linkage kit(top mounting)
110mm 440mm
190m
m
Filter adds 70mm to the length of the long throttle bodies.
Engine Internals Options and Upgrades
Mechanical Fitting Options and Upgrades
For engines that are expected to spend a lot of time at high engine speeds, such as those which are intended for competition use orextended trackday use, extra safety can be inbuilt through the upgrade to ARP big-end bolts and uprated valve springs.
Uprated Big-end bolts Uprated Valve Springs
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 18
170-
200
bhp
Zete
c E
ngin
e
Fuel pipe – the engine package is as standard for use with push-on rubber pipe. For those using braided hosing throughout the vehicle,an upgrade to dash 6 pipe fittings is available for the fuel rail and pressure regulator.Brake servos – if your vehicle requires a brake servo vacuum, the manifold can be fitted with a vacuum take-off. This can be specified toexit to the either side of the engine.
Push-on to screw-on fuel rail and pressureregulator upgrade (-6)
Brake servo adaptor
Side Water Rail – for inline applications where the thermostat housing would hit the bulkhead, the ‘side water rail’ allows the removal ofthe thermostat housing, so allowing the engine to be mounted further back. If a water header tank cannot be fitted to the vehicle, a pressurecap is available for the ‘side water rail’ to remove the need for the header tank. To allow extra clearance the ignition coil pack and bracketcan be unbolted and mounted remotely.
Side water rail Side water rail Standard Water Housing
Starter Motor – For inline specification engines there are two options available, standard remanufactured and new high power startermotors. For transverse specification engines the standard Ford start motor will have to be used.Bellhousing – A cast aluminium bell housing is available to suit the Ford Sierra type 9 (short input shaft) gearbox.
BellhousingStarter Motor
Flywheel and Clutch
Flywheel and Clutch - A standard flywheel and clutch is included with the engine to suit type9, MT75 and MTX75 gearboxes. A cost optionis available for a different flywheel / clutch assembly for users of the IB5 gearbox.
Ignition coil pack can be remotely mounted
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 19
170-
200
bhp
Zete
c E
ngin
e
With optional extra parts the Omex 600 ECU is capable of much more than simply running the engine;
Shift lights - a visual warning for the optimum rpm gearshift. Normally a high intensity 10mm red LED is used, but other sizes and coloursare available.Full throttle gearshift - gearshifts without lifting off the throttle. In the case of sequential gearboxes, even without using the clutch.Sequential gearboxes often have a switch inbuilt for input to the ECU, and those using a ‘normal’ gearbox can use an Omex clutch switch,signalling an ignition retard that temporarily reduces engine power output.Launch control - consistent fast starts. A button on the steering wheel that gives a temporary lower rev limit holding the engine steady onthe startline.Radiator fan control - reduce the number of joins and sensors in the cooling system, and have full programmability of the ON / OFFtemperatures for the radiator fan. An additional relay is required for this control.Barometric air pressure correction – If you are using the engine with large altitude changes (such as in the mountainous areas), thenair pressure changes due to the altitude changes will affect the amount of fuel required. An upgrade to fit an air pressure sensor toautomatically make these changes is available.Emissions control - The engine simply needs a narrowband lambda sensor and an effective catalytic convertor and it will then pass UKMOT and IVA emissions tests with ease. Omex can provide a lambda sensor and boss to weld to the exhaust. A lambda sensor is notrequired to make the engine run, so if you have a vehicle that does not need to pass emissions tests, then a lambda sensor is optional.Throttle position sensor – For use in extreme conditions such as off-road rallying, a contactless throttle position sensor can be used togive improved reliability due to improved protection against water and dust.
Shift light (10mm LED) Full throttle gearshift(clutch switch)
Launch control (button) Radiator fan control(Relay and base)
Barometric pressure sensorand harness upgrade
Lambda sensor Lambda sensor boss Throttle position sensorupgrade
Electronic Control Options and Upgrades
Why choose Omex Products?
The difference between winning and losing is very small. In hillclimbing and sprinting it can regularly be 0.05 secs, in circuit racing a halfcars length, in rallying one corner...........
So what makes Omex products win so many events and championships? Simple, attention to DETAIL.
The very basics of how the ECU works makes a big difference. How it calculates when an ignition spark is going to be placed, when it’scalculated, how engine acceleration is taken into account, and so ultimately how accurately that spark is placed, are things that you do notthink about when looking at ECUs. Here at Omex we do because those details that are often taken for granted are the difference betweenone ECU system and another, the difference between winning and losing... The detailed approach to design of the basics by our team oftop software and hardware design engineers, responsible for race wins throughout all forms of motorsport at the very highest levels, meansyou do not need to think about these details because we do. Features lists don’t win races; it’s how these features work that wins races.Other ECUs may have similar features lists, but how an Omex works makes all the difference. Naturally, Omex ECUs have all of thefeatures you would expect from a top level ECU.
Winning Championships is a combination of performance and reliability. Reliability is found in the details of the way the ECU is designedand built. All Omex ECUs are robot assembled in the UK on an ISO9001:2000 approved assembly line, ensuring a consistent, high qualitybuild. They are all then thoroughly tested, twice, before leaving Omex. A well running system is a combination of ECU and many othercomponents. It is important that all components in the system continue to work in order for the ECU to be able to perform, and so Omexsource all other components such as sensors and injectors only from highly respected manufacturers.
Of course, before you can even think about winning races and championships, you need to get to the race! Omex employ only degreequalified engineers to ensure that whenever you contact us you get only the very best advice, right from specification of the best parts foryour application, through to advice during installation, and finally, getting your engine running to its maximum potential.
And should something go wrong at any time during your ownership of your Omex ECU, the same team of technicians is available just atelephone call or mouse click away with free advice to help you through.
All these details have helped countless others win races and championships. Maybe you will be next…
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 20
170-
200
bhp
Zete
c E
ngin
e
Kit
Options and Upgrades
Lightweight steel flywheels (various options available)
Medium length throttle body upgradeShort throttle body upgradeInlet manifold upgrade
Throttle linkage, over, single cable for long/medium throttle bodiesThrottle linkage, over, twin cable for long/medium throttle bodies
Throttle linkage, under, single cable for long/medium throttle bodiesThrottle linkage, under, twin cable for long/medium throttle bodies
Throttle linkage, over, single cable for short throttle bodiesThrottle linkage, over, twin cable for short throttle bodies
Throttle linkage, under, single cable for short throttle bodiesThrottle linkage, under, twin cable for short throttle bodies
Air filter and machined back plate (long throttle bodies only)Air filter socks (set of 4)
Push-on to screw-on fuel rail and pressure regulator upgradeBrake servo adaptorsThrottle position sensor upgrade
Side water rail (complete assembly - fitted)
Starter motor (remanufactured)Starter motor (high torque)
Bellhousing (alloy, to fit Ford type 9 gearbox)
Uprated ARP big-end bolts - fitted to inline specification engineUprated ARP big-end bolts - fitted to transverse specification engine
Uprated valve springs - fitted to 170 bhp engineUprated valve springs - fitted to 200 bhp engine
Shift light (10mm LED - red) - inc mounting bezel and cablesShift light (5mm LED - red) - inc mounting bezel and cablesFull throttle gearshift clutch switch - inc cablesLaunch control button - inc cablesRadiator fan control relay and baseBarometric pressure sensor upgrade (inc harness upgrade)Lambda (oxygen) sensorLambda sensor boss
Part Number
THP45(U)TSP45(U)MF03(U)
CLS1 + LBO1CLD1 + LBO1
CLS1 + LBU1CLD1 + LBU1
CLS1 + LBO1 + LAO1CLD1 + LBO1 + LAO1
CLS1 + LBU1 + LAO1CLD1 + LBU1 + LAO1
OMEM9901OMEM9051
FPR535-6(U) + TBR32(U)OMEM9100TP8LH(U)
OMEM6003OMEM6004OMEM6010OMEM6011OMEM6100OMEM2100(U) + OMEM1520(U)OMEM2301OMEM2351
Retail
Ask
£80.00£42.00£42.00
£103.00£148.20
£103.00£148.20
£117.00£162.20
£117.00£162.20
£80.00£44.00
£18.60£15.00£43.00
£244.63
£85.00£185.00
£205.75
£150.00£200.00
£400.00£125.00
£7.80£7.80£5.00£8.00£4.00£126.00£55.00£5.00
Inc VAT
Ask
£94.00£49.3549.35
£121.03£174.14
£121.03£174.14
£137.48£190.59
£137.48£190.59
£94.00£51.70
£21.86£17.63£50.53
£287.44
£99.88£217.38
£241.76
£176.25£235.00
£470.00£146.88
£9.17£9.17£5.88£9.40£4.70£148.05£64.63£5.88
Inline 170 bhp Engine with Long Throttle BodiesTransverse 170 bhp Engine with Long Throttle Bodies
Inline 200 bhp Engine with Long Throttle BodiesTransverse 200 bhp Engine with Long Throttle Bodies
--
--
ZE20F020ZE20F020T
ZE20F040ZE20F040T
£3795.00£3195.00
£5295.00£4695.00
£4459.13£3754.13
£6221.63£5516.63
--
--
--
--
Optional parts are standalone extra parts and can be added to your kit at any time. Upgrade parts, designated by a ‘(U)’ in the partnumber, are upgrading parts in the kit and so are only available at the above prices at the time of kit purchase. They are available at anytime, but at the full price of the part.
-
---
--
--
--
--
--
---
-
--
-
--
--
--------
Price List: ZE20F020 and ZE20F040 (170/200 bhp) Throttle Bodies Inlet System
Engine shown is ZE20F020
E&OE. Price list (Retail) valid from 22/10/2010 until further notice. [email protected]%
--------
-
---
--
--
--
--
--
---
-
--
-
--
--
--------
-
---
--
--
--
--
--
---
-
--
-
--
--
--------
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 21
220
bhp
Zete
c E
ngin
e
Engine shown is ZE20SC010
220 BHP Engine ZE20SC010 (inline)Engine
-
Engine SpecificationNew Focus Zetec 2.0l Blacktop EngineRotrex Supercharger and Billet Aluminium BracketsReady Mapped 600 Series ECURace Spec Ready Built Wiring HarnessLowline Baffled SumpAlternator with Billet Aluminium Brackets & BeltStandard Exhaust Manifold (if required)Inlet ManifoldFuel RailFuel Pressure RegulatorThrottle Position SensorAir Temperature SensorCoolant Temperature SensorCrank Position SensorMAP SensorHigh Flow Rate InjectorsIgnition Coil Pack and LeadsOil FilterGaskets
How much power will my engine make?The power and torque graph show the results obtained from the engine, using a 4-1 exhaust manifold, catalytic convertor, and silencersystem. These results are from testing on Omex’s Superflow rolling road.
Engine Power Graphs
PowerTorque
100
125
150
175
2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000RPM
50
75
BH
P /
Torq
ue
Zetec Blacktop 220 bhp Engine Kit Power Graph
ZE20SC010
200
225
250
Centrifugal Supercharged Zetec Engine - 220 bhp
If you want to take your car to the next performance level but do not want the unfortunate road manners of a highly tuned engine, our220bhp supercharged engine may be for you. Developed over 12 months of hard track use, this specification offers perfect road mannersbut with a torque output that cannot be matched by any normally aspirated 2L Zetec engine. With almost 190 lbft of torque, accelerationin any gear is instant and rapid. Fitted as standard with ARP connecting rod bolts, this is a tough package that can be enhanced furtherwith various options and upgrades to make your car super quick. Because of the nature of the Rotrex supercharger, boost builds gentlywith increasing engine revs, so ensuring that the engine retains perfect road manners and is easy and safe to drive in the wet, but offersexhilarating acceleration when unleashed. Being one of the two official Rotrex importers for the UK, we have a huge knowledge of theseunits and can offer advice about intercooler installation and cooling requirements. Available as an inline (front engine, rear wheel drive)spec only, this engine is fitted as standard with the RaceLine lowline alloy sump to allow maximum ground clearance.
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 22
220
bhp
Zete
c E
ngin
e
Electronics
What comes with the engine?
Omex’s multi-championship winning 600 Series ECU controls the fuel injection, standard Ford distributorless ignition coil pack, andoptionally, many other functions around the vehicle. The ECU is connected to the hardware with a complete, DR25 Raychemheatshrunk, race specification wiring harness, which is fully tagged and with the correct connections made for your Zetec engine,ensuring easy clip-on fitment. The ECU, wiring harness and sensors are kept with each engine build throughout assembly and testingwork, ensuring that the engine package you receive has been tested as a whole package.
Unlike other superchargers, the centrifugal compressor design of the Rotrex supercharger continues to efficiently make boost at higherengine speeds. This results in an engine that continues to make power at high engine speeds, giving engine driving characteristicssimilar to a naturally aspirated engine, but with more power! This is the same family of superchargers as proved on the KoenigseggCCXR! The unique drive system inside the supercharger, using a traction drive rather than conventional gears also ensures quiet andreliable running. The supercharger is held in paced by a hard-anodised CNC machined billet aluminium bracket.
Designed to fit universally into kit cars, the supercharger can be bolted in three different rotational positions fifteen degrees apart on theanodised billet alloy bracket. In addition the compressor housing can be rotated in sixty degree increments allowing for the dimensionsof your application.
Supercharger
Supercharger Example Installation Supercharger and Bracket
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 23
220
bhp
Zete
c E
ngin
e
ARP Uprated Big End Bolts
ARP uprates big end bolts are supplied and fitted to the 220bhp supercharged engine.
Ignition
DIS coil pack, ignition leads, and spark plugs are all included
Lightweight hard-anodised billet aluminium brackets are used to mount the high output 2 wire alternator and associated belt pulleys.
Alternator
The engine utilises a fuel pressureregulator built into the fuel rail.
Fuel Regulator
Bosch high flow rate injectors areused on the engine giving excellentspray patterns to optimise poweroutput and emissions.
Injectors
Sump
Inline engines have cornering forces in a different direction on the engine and so the inline specification engines are fitted with a newsump with internal baffling designed to keep the oil on the pickup. This sump has been tested in vehicles up to single seater with slicksand wings generating very high cornering forces. Note that the supercharged engine is not suitable for transverse mounting.
Crank, throttle position, air and coolanttemperature sensors are supplied andfitted to all engines. MAP sensor issupplied for remote fitment.
Sensors
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 24
220
bhp
Zete
c E
ngin
e
All dimensions are approximate if you need any other dimensions please ask.
Engine Dimensions
-Ignition coil pack can be removed and mounted remotely-Exhaust manifold can be replaced with customers own exhaust manifold-Optional side water rail reduces the size of the water housing (see options list)-Oil filter can be changed for a shorter filter
490mm
550m
m
580m
m
Front ofpulleys
Rear ofblock
Rear ofcoil
125mm
Bot
tom
of
sum
pTo
p of
oil
cap
& c
am c
over
125mm
490mm
565mm
Rear ofblock
Rear ofcoil
Front ofpulleys
Back ofWater housing
Cra
nkce
ntre
line
200m
m32
0mm
270mm
455mm
520mmSide of
inlet manifoldSide of
exhaust manifold& water pump
Top ofinlet
manifold
Bottom ofinlet
manifold
320m
m60 m
m50 m
m
Sid
e of
inle
t man
ifold
Sid
e of
exha
ust m
anifo
ld&
wat
er p
ump
Cra
nkce
ntre
line
Bot
tom
of
sum
p150m
m43
0mm
Top
ofca
m c
over
Bottom ofsupercharger
bracket
50 mm
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 25
220
bhp
Zete
c E
ngin
e
Options and Upgrades
Starter Motor – For inline specification engines there are two options available, standard remanufactured and new high power startermotors.Bellhousing – a cast aluminium bell housing is available to suit the Ford Sierra type 9 (short input shaft) gearbox.
BellhousingStarter Motor
Flywheel and Clutch
Engine Internals Options and Upgrades
Side Water Rail – for inline applications where the thermostat housing would hit the bulkhead, the ‘side water rail’ allows the removal ofthe thermostat housing, so allowing the engine to be mounted further back. If a water header tank cannot be fitted to the vehicle, apressure cap is available for the ‘side water rail’ to remove the need for the header tank. To allow extra clearance the ignition coil packand bracket can be unbolted and mounted remotely.
Side water rail Side water rail Standard Water Housing
Mechanical Fitting Options and Upgrades
For engines that are expected to spend a lot of time at high engine speeds, such as those which are intended for competition use orextended trackday use, extra safety can be inbuilt through the upgrade to uprated big-end bolts and uprated valve springs.
Uprated Valve Springs
Flywheel and Clutch - For options please contact Omex.
Ignition coil pack can be remotely mounted
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 26
220
bhp
Zete
c E
ngin
e
With optional extra parts the Omex 600 ECU is capable of much more than simply running the engine;
Shift lights - a visual warning for the optimum rpm gearshift. Normally a high intensity 10mm red LED is used, but other sizes and coloursare available.Full throttle gearshift - gearshifts without lifting off the throttle. In the case of sequential gearboxes, even without using the clutch.Sequential gearboxes often have a switch inbuilt for input to the ECU, and those using a ‘normal’ gearbox can use an Omex clutch switch,signalling an ignition retard that temporarily reduces engine power output.Launch control - consistent fast starts. A button on the steering wheel that gives a temporary lower rev limit holding the engine steady onthe startline.Radiator fan control - reduce the number joins and sensors in the cooling system, and have full programmability of the ON / OFFtemperatures for the radiator fan. An additional relay is required for this control.Emissions control - The engine simply needs a narrowband lambda sensor and an effective catalytic convertor and it will then pass UKMOT and IVA emissions tests with ease. Omex can provide a lambda sensor and boss to weld to the exhaust. A lambda sensor is notrequired to make the engine run, so if you have a vehicle that does not need to pass emissions tests, then a lambda sensor is optional.Throttle position sensor – For use in extreme conditions such as off-road rallying, a contactless throttle position sensor can be used togive improved reliability due to improved protection against water and dust.
Shift light (10mm LED) Full throttle gearshift(clutch switch)
Launch control (button) Radiator fan control(Relay and base)
Lambda sensor Lambda sensor boss Throttle position sensorupgrade
Electronic Control Options and Upgrades
Why choose Omex Products?
The difference between winning and losing is very small. In hillclimbing and sprinting it can regularly be 0.05 secs, in circuit racing a halfcars length, in rallying one corner...........
So what makes Omex products win so many events and championships? Simple, attention to DETAIL.
The very basics of how the ECU works makes a big difference. How it calculates when an ignition spark is going to be placed, when it’scalculated, how engine acceleration is taken into account, and so ultimately how accurately that spark is placed, are things that you do notthink about when looking at ECUs. Here at Omex we do because those details that are often taken for granted are the difference betweenone ECU system and another, the difference between winning and losing... The detailed approach to design of the basics by our team oftop software and hardware design engineers, responsible for race wins throughout all forms of motorsport at the very highest levels, meansyou do not need to think about these details because we do. Features lists don’t win races; it’s how these features work that wins races.Other ECUs may have similar features lists, but how an Omex works makes all the difference. Naturally, Omex ECUs have all of thefeatures you would expect from a top level ECU.
Winning Championships is a combination of performance and reliability. Reliability is found in the details of the way the ECU is designedand built. All Omex ECUs are robot assembled in the UK on an ISO9001:2000 approved assembly line, ensuring a consistent, high qualitybuild. They are all then thoroughly tested, twice, before leaving Omex. A well running system is a combination of ECU and many othercomponents. It is important that all components in the system continue to work in order for the ECU to be able to perform, and so Omexsource all other components such as sensors and injectors only from highly respected manufacturers.
Of course, before you can even think about winning races and championships, you need to get to the race! Omex employ only degreequalified engineers to ensure that whenever you contact us you get only the very best advice, right from specification of the best parts foryour application, through to advice during installation, and finally, getting your engine running to its maximum potential.
And should something go wrong at any time during your ownership of your Omex ECU, the same team of technicians is available just atelephone call or mouse click away with free advice to help you through.
All these details have helped countless others win races and championships. Maybe you will be next…
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 27
220
bhp
Zete
c E
ngin
e
Kit
Options and Upgrades
Lightweight steel flywheels (various options available)
Side water rail (complete assembly - fitted)
Starter motor - remanufactured (inline only)Starter motor - high torque (inline only)
Bellhousing (alloy, to fit Ford type 9 gearbox)
Uprated valve springs - fitted to 220 bhp supercharged engine
Shift light (10mm LED - red) - inc mounting bezel and cablesShift light (5mm LED - red) - inc mounting bezel and cablesFull throttle gearshift clutch switch - inc cablesLaunch control button - inc cablesRadiator fan control relay and baseLambda (oxygen) sensorLambda sensor boss
Part Number
OMEM6003OMEM6004OMEM6010OMEM6011OMEM6100OMEM2301OMEM2351
Retail
Ask
£244.63
£85.00£185.00
£205.75
£400.00
£7.80£7.80£5.00£8.00£4.00£55.00£5.00
Inc VAT
Ask
£287.44
£99.88£217.38
£241.76
£470.00
£9.17£9.17£5.88£9.40£4.70£64.63£5.88
220 BHP Supercharged Engine - ZE20SC010 £5495.00 £6456.63- -
Optional parts are standalone extra parts and can be added to your kit at any time. Upgrade parts, designated by a ‘(U)’ in the partnumber, are upgrading parts in the kit and so are only available at the above prices at the time of kit purchase. They are available at anytime, but at the full price of the part.
-
-
--
-
-
-------
-
-
--
-
-
-------
-
-
--
-
-
-------
Price List: ZE20SC010 (220 bhp) Supercharged
Engine shown is ZE20SC010
E&OE. Price list (Retail) valid from 22/10/2010 until further notice. [email protected]%
Road Track Race Ltd, 42 Mount Street, New Basford, Nottingham, NG7 7HXTel +44 (0)115 9780677 Fax +44 (0)115 8377973 www.roadtrackrace.com 28
Top Related