User's Manual
-1-
Contents
Caution ...................................................................................... 2
Safety Information ...................................................................... 3
Control Button ............................................................................ 5
.................................................................................... 6
.................................................................... 7
................................................................................ 9
ON/OFF Power ......................................................................... 11
.............................................................................. 11
Menu Operation ........................................................................ 11
..........................................................................
Specifications ........................................................................... 21
Simple Troubleshooting ............................................................. 22
Terminal
Connection
Input Source
The Remote Control
Main launcher 16
-2-
Caution
The lightning flash with the arrowhead symbol, inside an equilateral triangle is intended to alert
the user of the presence of un-insulated dangerous voltage within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to the user.
The exclamation mark inside an equilateral triangle is intended to alert the user of the presence
of important operating and maintenance (servicing) instructions.
Safety Information
To ensure reliable and safe operation of this equipment, please read all the
instructions in this user guide, especially the safety information below.
Electrical safety
The TV set should only be connected to a main power supply as stated on the label
on the back of the product.To prevent overload, don't share the same mains supply socket with
too many items.
Do not place any connecting wires where they may be stepped on or tripped over.
When removing the plug from the wall socket, make sure to pull the plug and not the wires.
During a thunderstorm or while leaving the TV for long periods, disconnect the aerial
(if outdoor) and mains from the power supply.
Do not allow water or moisture to enter the TV or main adaptor. Do NOT use in wet or moist
areas such as bathrooms, steamy kitchens or near swimming pools.
Pull the plug out immediately, and seek professional help if:
The main plug or cable is damaged.
Liquid is spilt onto the set, or if it is accidentally exposed to water or moisture.
Anything accidentally penetrates the ventilation slots.
The set doesn't function properly.
Do not remove the safety covers. There are no user serviceable parts inside.
You may invalidate the warranty. Only qualified personnel can service this apparatus.
Remove exhausted batteries from the remote control handset to avoid battery leakage
or when not using it for a long period.
Physical safety
Do not block ventilation slots in the back cover. You may place the TV in a cabinet,
but ensure that there is at least 5cm (2'') clearance all around.
Do not tap or shake the TV screen. You may damage the internal circuits. Take good care of
the remote control, do not drop it.
To clean the TV use a soft dry cloth. Do NOT use solvents or petrol based fluids.
For stubborn stains, you may use a damp soft cloth with diluted detergent.
A warning that an apparatus with CLASS I construction shall be connected to a MAIN socket
outlet with a protective earthing connection.
Where the MAIN plug or an appliance coupler is used as the disconnect device,
the disconnect device shall remain readily operable.
● ● ● ● ●
●
●
●
●
-3-
Safety Information
IMPORTANT SAFETY INSTRUCTIONS
Owne 'sr Manual
5. Do not use this apparatus near water.
6. Only clean with a dry cloth.
7. Do not block any of the ventilation openings.
Install in accordance with the
instructions.
manufacturer's
WARNING :
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
The apparatus should not be exposed to dripping or splashing liquids and no objects filled with liquids,
such as vases, should be placed on the apparatus.
1. Read these instructions.
2. Keep these instructions.
3. Note all warnings.
4. Follow all instructions.
8. Do not install near any heat source such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9. Do not defeat the safety purpose of the
polarized or grounding type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong is provided for your safety.
When the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
10. Protect the power cord from being walked
on or pinched particularly at plugs.
11. Only use the accessories specified by the
manufacturer.
-4-
13. Unplug this apparatus during lightning
storms or when it is unused for a long time.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in
any way.
Note
- If the TV is cold, there may be a small flicker when you turn it on.
- Avoid touching the LCD screen or holding your finger(s) against it.
CAUTION connecting the Power Cord
Do not overload wall outlets. Overloaded wall outlets could damage the TV and could result in electric
shock or fire. examine the cord of your appliance. If its appearance indicates damage or
deterioration, unplug it. Stop using it until you have it replaced with a cord authorized by your dealer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked or pinched.
Frequently
Safety Information
On Disposal
- The fluorescent lamp used in this product contains a small amount of
- Disposal of this product must be carried out in of your local authority.
mercury.
accordance with the regulations
12. Only use a cart, stand, tripod, bracket,
or a table specified by the manufacturer
or which is sold with the apparatus.
Control Button
-5-
STAND BY(or POWER):
-(CH/VOL)+: hort press to change channel, long press to adjust sound volume.
CH+/-: Selecting channel.
VOL+/-: Adjusting volume.
MENU:
SOURCE(or INPUT):
Standby or switch on the TV.
S
Display or exit MENU.
External signal input selection.
Note:
Some models has 5 buttons, some models has 7 buttons.
The following is only functional schematic, And the actual position and arrangement of
different models may be different.
1 2 3 4 5
1 2 3 4 5 6 7
RF INHDMI2 IN
PC IN
PC Audio IN
HDMI1 IN(ARC)
Ethernet
The LED TV has large multimedia function, which can be connected with many kinds of
The following a paragraph shows how it connect with other Audio and Video devices.
equipments.
Terminal
-6-
1.HDMI: Connect it to the HDMI of DVD or other equipment.
2. VGA(PC): For PC display. Connect it to the D-Sub 15 pins anglog output connector of the PC.
3. VGA AUDIO IN(PC IN): Connect it to the audio output terminal of PC.
4. COAXIAL: Coaxial audio signal out plug.
5. AV IN: Connect it to video output terminal of DVD.
(AV AUDIO IN): Connect it to the audio output terminal of DVD.
6.COMPONENT: Connect them to the video output terminal of DVD.
7. RF: Connect antenna or cable 75 Ohm coaxial to receive TV signal.
8. USB: USB input to play multimedia.
9. EARPHONE OUT: It can be connected to the headphone.
10. RJ45 IN (RJ45 input port).
11. TF CARD.
Audio-L
Audio-R
Coaxial OUT
TF CARD11
USB IN
USB IN
Y
The Remote Control
-7-
The remote controller cannot be used unless it is within the receivable range. Before you
use the remote control, please make sure there's no obstacle between the remote control
and the receiver.
1. POWER) BUTTON
Switch On/Off the TV when on standby mode.
2. MUTE BUTTON
Press the button to turn off the volume.
Press it again to turn on the volume.
3. HOME BUTTON
Press to enter TV main interface.
4. SOURCE BUTTON
Press the button to display Source menu.
During Video Record, press the button to
stop record.
5. 0-9 BUTTON
6. VOL+/VOL- BUTTON
7. ENTER(OK) BUTTON
Press the button to confirm or enter sub menus.
8. MENU BUTTON
9. BUTTON
10. RETURN BUTTON
Return function
11. UP, DOWN, LEFT, RIGHT ARROW BUTTONS
Press these buttons to select or adjust the
desired item on the TV menu.
UP/DOWN: Choose channel.
12. RED/GREEN/YELLOW/BLUE BUTTONS
According to the interface prompt operation.
The following functions are not
RED:
GREEN: Open/Close Electronic Program Guide.
BLUE:
STANDBY(
Select the TV channel you want to view by using
the number buttons.
Increase/decrease the volume level.
Display or exit MENU.
Display information of the current channel.
or exit .
DISPLAY
applicable to
all the models.
Press this button to enter to TELETEXT mode.
.PVR function for DTV
2
10
7
9
4
3
5
1
11
8
12
6
-8-
The Remote Control
Using the remote control
Open the battery door and insert 2 "AAA" batteries.
Point the remote control at the remote sensor located on the unit.
When there is a strong ambient light source, the performance of the infrared remote sensor
may be degraded, causing unreliable operation.
The recommended effective distance for remote operation is about 16 feet (5 meters).
When the batteries become weak and the operating distance of the remote control is
greatly reduced , you will need to replace the batteries.
If the remote control is not going to be used for a long period of time, remove the batteries
to avoid damage caused by battery leakage or corrosion.
Do not mix old and new batteries or ALKALINE or standard (CARBON-ZINC) or
rechargeable (NICKEL-CADMIUM) batteries.
Always remove batteries as soon as they become weak.
Weak batteries can leak and severely damage the remote control.
Do not dispose of batteries in fire, they may explode or leak. Batteries should not be
exposed to excessive heat such as sunshine, fire or the like.
●
●
●
●
●
●
●
●
●
●
CAUTION : Danger of explosion may occur if battery is incorrectly replaced.
Antenna
Connect the 75 OHM coaxial cable from the antenna to the antenna socket on the rear
panel, as shown above.
Note:
For better reception,
an external roof-mounted antenna is recommended.
For UHF TV reception, use the specified UHF antenna.
When using 300 OHM flat cable, a 300 OHM-75 OHM adapter should be used for a
proper connection to the antenna jack (The adaptor is not supplied).
especially in outlying areas or where ghost effect or interference occur,
Consult a local AV technician.
VHF TV ANTENNA
UHF TV ANTENNA
75 OHM COAXIAL CABLE
300 OHM FLAT CABLE
To TV ANTENNA JACK
300 OHM 75 OHM ADAPTOR
75 OHM DIN
-9-
Connection
-10-
Connection
-11-
Menu operation
Input Source
● [ ]
● [ ]
● [ ]
Press SOURCE button to display the input source list.
Press button .
Press ENTER button to enter the selected source.
to select the input source you want
ON/OFF Power
Connect the power plug to the household power outlet.
Press main power switch on TV unit (some models without power switch).
Thereafter press the [STANDBY] button to open or switch the receiver off.
Note:
Remove plug from the power outlet when not using it for a long period of time.
1.
the
sub
return
Press the [MENU] button to
2. Press the button to
Press the nter.
. Press the button to
Press the button to or
press the [ ] button to enter
menu.
. Pr
Press the [MENU] button to exit
enter menu.
[ ] select menu.
[ENTER] to e
3 [ ] select item.
[ ] adjust
ENTER
4 ess the [EXIT] button to .
5. .
-12-
Menu Operation
Sound
Picture
●
●
●
You can clear up the input signal by setting the item.
●
Select the color temperature.
●
● Automatically adjust picture detail and brightness.
Picture Mode:
Select the favorite picture mode.
Contrast/Brightness/Color/Sharpness/Hue:
Adjust picture settings.
Hue is only workable with NTSC system in AV mode.
Noise Reduction:
Color Temp:
favorite
Aspect Ratio: Set the aspect ratio of the screen.
DLC:
●
●
●
●
● Automatically adjusts volume when chang programs
or channels.
● SPDIF:
●
●
Sound Mode:
favorite
Bass: Adjust the low frequency sounds.
Treble: Adjust the high frequency sounds.
Balance: Adjust the level of sound coming from the left and
right speakers.
AVC:
Select the sound mode.
Audio Only
Set output format of the coaxial audio.
lay audio only with the video turned off.
Surround: Select to ON/OFF.
: P
-13-
Menu Operation
Channel
●
●
●
●
●
●
●
●
Antenna Type: Select the antenna type.
Auto Scan: Searching programs automatically.
P
Anolog Manual Scan: Searching the ATV programs by input
the frequency.
Digital Manual Scan: Searching the DTV programs by input
the frequency.
ress [EXIT] to stop searching.
Channel: Set the channel number.
Color system: Select the color system.
Sound System: Select the sound system.
Frequency: Input the frequency of the channel.
Note: The Channel Menu is available only in TV mode.
Press to Edit the Channel List.
:
Hearing Impaired Set On/ Off.
Audio Description Set On/ Off.
[MENU]
Press to skip the select channel.
(TV set will skip the channel automatically when using
CH+/- to view the channels.)
Press to delete the channel.
Press to enter the rename state.
Fav:
Preferences Set your preference for audio.
:
:
button
Subtitle
● Move: Press to move channel position
● S
● Delete:
● Rename:
●
●
●
●
●
●
Select a subtitle language can be displayed.
kip:
Add or Delete the channel to your favorite list.
Audio Language: Select the language supported by the
chosen digital channel. It is only available in DTV.
Language:
● Channel List: List the programs.
-14-
Menu Operation
● OSD Language: Set the OSD display language.
● Blue Screen: Set the background in blue or black when no signal input.
● PVR Setting: Insert storage device such as USB or TF card, and enter sub menu.
Press [PVR] button to start recording TV program, press [source] to stop recording.
Note: PVR is only workable in DTV mode.
● Teletext: Select teletext language.
● HDMI CEC Setup: Enter the sub menu.
● CEC: When this item is set to ON, CEC can be active.
● Tv Auto Power on: This item is set to ON, HDMI is connected to the signal
source (DVD), and both the signal source and TV are turned off. When the signal
source is turned on, TV turns on automatically and switches to the HDMI channel.
When this item is set to OFF, TV can not be turned on.
● Device Auto Power Off: This item is set to ON, HDMI is connected to the signal
source (DVD), and both the signal source and TV are turned on.
When TV is turned off, the signal source turns off automatically.
This item is set to OFF, TV is turned off, DVD can not be turned off.
● ARC: When this item is set to ON and the ARC function can be active.
TV transmits its audio directly to the amplifier receiver via the HDMI (1.4) cable.
Then TV remote control can adjust the volume of the amplifier receiver.
● Device List: Display device list.
● Device Menu: Display device menu.
● Reset: Restore the default setting.
Setting
-15-
Menu Operation
●
●
OSD Timer: Select OSD Timer
Sleep Timer: Select Sleep Timer
.
.
Time
PC Adjust
Connect the PC t to computer, and select PC source.
Automatically adjust.
Shift the screen left or right.
Shift the screen up or down.
erminal
● Auto Adjust:
● Horizontal Position:
● Vertical Position:
● Clock Phase: Adjust the internal signal phase.
● Sampling Clock: Adjust the internal sampling clock rate.
-16-
Main launcher
Main launcher
Press the [HOME] button to enter the main launcher.
Press [ ] to select the menu.
Press [ENTER] button to select or set .
Add the commonly-used application independently by selecting “+” on the home page.
Select one application and press [enter] for a long time to delete this application.
You can select and enter option [App List] to view all ready applications programs in this TV.
You also can install more applications downloaded from Internet.
Note:
● If the system space is insufficient during the installation of application programs, a
prompt will be given and the installation will become impossible. You are suggested to
uninstall some applications, in order to reserve sufficient space for new applications.
● Before operation, please check whether the network connection is available;
if the network condition is in a bad situation, pause or skip will appear during playing.
● The problem of slow loading or fail loading of the video played online caused by the
program server distribution shall be of irrelevance with this machine.
-17-
Main launcher
Net mode: Select Wire net or Wireless.
Wire network:
Insert the Ethernet cable ,and select Auto
get IP address to connect the Ethernet.
Wireless Network:
Select the WIFI, and press the password
to connect.
System Setting
Select the Settings] in the Main Menu to enter the System Setting. [
Auto Attach: Get current time and
date automatically.
24 Hours: Select 12 hours or 24 hours.
Time Zone: Select local time zone.
Time Edit: Edit current time and date.
Date Format: Set current date format.
Language Setting:
Select current display language.
Input Method: Select the Input method.
System Recovery:
Recovery system to original state.
-18-
Main launcher
Multimedia
Select option MEDIA to enter Multimedia, select the Video/Music/Photo/Folder,
and press the [ENTER] button to enter.
Press key [menu] during play, operation menu will display on the screen.
Main launcher
-19-
EshareServer
Press the [HOME] to enter APP List,
and select the EshareServer.
Scan the QR code to install the
EshareServer.
Phone
Open the Eshare, and Connect.
Optional function:
Remote Control/TV Mirror/Mirroring.
Android Iphone
Remote Contrl/Control
Optional function:
Keys/Touch/Mouse/AirMouse.
Main launcher
-20-
TV Mirror
Select the TV Mirror, and enter it, then your phone will show the screen of the TV.
Mirroring
Select the Mirroring function, and enter it, then you can cast the screen of your
cellphone to the TV.
-21-
Specifications
Note:
Design and specifications are subject to change without notice.●
● When play multi-media, insert USB to connect TV. Due to programs maybe be made
by different coded system under same format name, this TV cannot ensure supporting all
formats listed above.
Video System
Reception Range
Sound System
PAL /SECAM
48.25MHz~863.25MHz
BG, DK, I
ATV
Reception Range
VHF(52.5MHz~219MHz)
UHF(474MHz~866MHz)
DTV
Standby Power Consumption
Power Consumption
Input Impedance 75Ω
≤0.50W
refer to the rating label
Supply Voltage refer to the rating label
PHOTO: MUSIC: MOVIE:
JPEG、BMP、PNGMP3、AC3AVI、MP4、MKV、MOV、MPG、VOB、TS、RM、RMVB
Component format support
HDMI format support
480i, 480p, 720p, 1080i, 1080p
720p, 1080i, 1080p, 2160p
The readable file types from Media (USB)
DVB-C/DVB-T/DVB-T2
Video System
Sound System
Basic Functions
MPEG-2, MPEG-4, H.264
MPEG-1 layer 1/2, MPEG-2 layer 2
EPG, PVR, Subtitle, TELETEXT
Modulation
If the display fails or the performance dramatically changes, check the display in
accordance with the following instructions. Remember to check the peripherals to
pinpoint the source of the failure. If the display still fails to perform as expected,
contact the dealer for assistance.
No Power
No Sound
Remote notresponding
Symptom DEALING METHOD
TV set needs to becleaned
Some Interference InThe VGA Mode
Abnormal Color
The Screen FlashesIn VGA Mode
Check the power connection.Pull the plug out, wait for 60 seconds, then reconnect the power and turn on the set.
Increase the volume. Check if the set is on the mute state or not. Check the voice setting condition. Check the voice mode setting condition.
Check the effect of the batteries. If necessary, replace thebatteries or clean the remote control sensor window. The distance between the set and the remote control should be less than 6 meters.
The parameter is too big.Please use safety mode when restarting the PC and set the parameter of the monitor according to the instructions.
Modify parameter of the monitor according to the instruction manual.
Check the antenna connection.
Please pull the plug out when cleaning the screen. Use a soft, clean cloth to wipe it off. If needed to clean further, please use dry cloth, do not use naphtha or other thinners liquids.
Simple Troubleshooting
-22-
TP.MS638.PC822-02A
Top Related