ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
CUPRINS / T.O.C.Informații tehnice / Technical informations 4Șuruburi cu filet trapezoidal / Trapezoidal screws 24Piulițe cu filet trapezoidal / Trapezoidal nuts 36
www.powerbelt.ro
Producătorul articolelor / Producer of the items:4 www.powerbelt.ro
INFORMAȚII TEHNICE TECHNICAL INFORMATIONS
Șuruburile furnizorului nostru sunt fabricate cu rectiliniaritate controlată. Rectiliniaritatea șurubului se evaluează măsurând variația deviației „ƒ“, atunci când șurubul este sprijinit la capete pe două reazeme și rotit ușor.
Our supplier’s screws are produced with controlled straightness.Screw straightness is appraised by measuring the variation of the deflection “ƒ” when the screw is supported at the ends on two constraints and slightly rotated.
Desen explicativ privind rectiliniaritatea Drawing for straightness
Condiția cu autoblocare Self-locking condition
Unghiul de înclinare a elicei șurubuluiLead angle of the screw
Cu autoblocare Self-locking
< 2°30’
Parțial cu autoblocare Partially self-locking
2°30’ - 6°
Fără autoblocare Not self-locking
> 6°
tNOTĂ: Șuruburile cu autoblocare parțială se pot debloca printr-o acționare mai energică! NOTE: The partly self-locking screws fiercer shaking may unlocking!
Duritatea suprafeței Surface hardness
Material Material
Duritate Hardness
C15 (KEQ, KQX) 160/180 HB
C45 (KUE, KTS, KKA) 250HB
A2 (KRP, KRE) 260HB
A4 (KAM) 280HB
Precizia de poziționare a șurubului cu filet trapezoidal Positioning accuracy of the trapezoidal screw
Tip de șurub Screw type
Precizia filetului Lead accuracy
Eroarea pasului pe o lungime de 300 Pitch error in 300 length
KTS 100 (200*) +/- 0,1 mm
KUE 100 (200*) +/- 0,1 mm
KKA 50 +/- 0,2 mm
KQX 20 +/- 0,2 mm
KEQ 20 +/- 0,2 mm
KRP 20 +/- 0,2 mm
KAM 20 +/- 0,2 mm
* - în cazul dimensiunii mai mari de 80x10 / in case of bigger size than 80x10
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
5www.powerbelt.ro
Materiale Materials
ȘURUB CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW
Material Material
Compoziție Composition
C15 (KEQ, KQX) EN 10084 C15E - 1.1141
C45 (KUE, KTS, KKA) EN 10083-2 1C45 - 1.0503
A2 (KRP, KRE) AISI 304 -1.4301
A4 (KAM) AISI 316 - 1.4401
PIULIȚĂ CU FILET TRAPEZOIDAL TRAPEZOIDAL NUT
Material Material
Compoziție Composition
Oțel / Steel EN 10277-3 11SMnPb37 – 1.0737
Oțel / Steel EN 10277-3 11SMn30 – 1.0715
Oțel inoxidabil / Stainless steel INOX A1- AISI 303 – 1.4305
Alamă / Brass EN 12164 CW614N-M
Bronz / Bronze EN 1982 CuSn5Zn5Pb5-C – CC491K
Bronz / Bronze EN 1982 CuSn7Zn4Pb7-C – CC493K
Bronz / Bronze EN 1982 CuSn12-C – CC483K
Bronz / Bronze EN 1982 CuAl11Fe6Ni6-C – CC483K
Plastic / Plastic PA 6 + Mo S2 DIN 7728
Plastic cu autolubrifiere / Self-lubricating plastic PA 6 + Mo S2 DIN 7728 + lubricating
STRUCTURA CODULUI DE COMANDĂ ORDER CODE STRUCTURE
ȘURUB CU FILET TRAPEZOIDAL / TRAPEZOIDAL SCREW 79. 002. 001
Simbolul șurubului cu filet trapezoidal / Sign of the trapezoidal screw
Tipul de șurub cu filet trapezoidal / Sign of the trapezoidal screw (KEQ, KTS, KRP… )
Sensul elicei și lungimea șurubului / Sign of the screw length and helix (L=1m, L=2m, L=3m)
PIULIȚĂ CU FILET TRAPEZOIDAL / TRAPEZOIDAL NUT 79. 009. 001
Simbolul piuliței cu filet trapezoidal / Sign of the trapezoidal nut
Tipul de piuliță cu filet trapezoidal / Sign of the trapezoidal nut (MZP, FTN, HSN… )
Sensul elicei și lungimea piuliței / Sign of the nut helix (dreapta, stânga / right, left)
Producătorul articolelor / Producer of the items:6 www.powerbelt.ro
Date tehnice pentru piulițe technical details for nuts
piuliță / nut
șurub / screw
H1 = 0,5*Ph3 = H4 = H1 + ac = 0,5*P + a*cz = 0,25*P = H1/2
d3 = d - 2*h3d2 = D2 = d-2*z = d - 0,5*PD2 = d + 2*ac
ac = joc la fundul filetului bottom playes = abatere superioră șurub top deviation for screws = 0,26795 es
R1 max = 0,5*acR2 max = ac
Ø x Pasul filetului Ø x Lead
D4H
(mm)
D27 H
(mm)
D14 H
(mm) Începuturi de filet Thread starts
Joc radial Radial play
Joc axial Axial play
min min. max. min. max. min. max. min. max.
Tr 10 x 2 10.500 9.000 9.250 8.000 8.236 1 0.071 0.511 0.019 0.137
Tr 10 x 3 10.500 8.500 8.780 7.000 7.315 1 0.085 0.577 0.023 0.155
Tr 10 x 4 (P2) 10.500 9.000 9.250 8.000 8.236 2 0.071 0.511 0.019 0.137
Tr 12 x 3 12.500 10.500 10.800 9.000 9.315 1 0.085 0.609 0.023 0.163
Tr 12 x 6 (P3) 12.500 10.500 10.800 9.000 9.315 2 0.085 0.609 0.023 0.163
Tr 14 x 3 14.500 12.500 12.800 11.000 11.315 1 0.085 0.609 0.023 0.163
Tr 14 x 4 14.500 12.000 12.355 10.000 10.375 1 0.095 0.715 0.025 0.192
Tr 14 x 6 (P3) 14.500 12.500 12.800 11.000 11.315 2 0.085 0.609 0.023 0.163
Tr 16 x 4 16.500 14.000 14.355 12.000 12.375 1 0.095 0.715 0.025 0.192
Tr 16 x 8 (P4) 16.500 14.000 14.355 12.000 12.375 2 0.095 0.715 0.025 0.192
Tr 18 x 4 18.500 16.000 16.355 14.000 14.375 1 0.095 0.715 0.025 0.192
Tr 18 x 8 (P4) 18.500 16.000 16.355 14.000 14.375 2 0.095 0.715 0.025 0.192
Tr 20 x 4 20.500 18.000 18.355 16.000 16.375 1 0.095 0.715 0.025 0.192
Tr 20 x 8 (P4) 20.500 18.000 18.355 16.000 16.375 2 0.095 0.715 0.025 0.192
Tr 20 x 20 (P5) 20.500 17.500 17.875 15.000 15.450 4 0.106 0.761 0.028 0.204
Tr 22 x 5 22.500 19.500 19.875 17.000 17.450 1 0.106 0.761 0.028 0.204
Tr 22 x 10 (P5) 22.500 19.500 19.875 17.000 17.450 2 0.106 0.761 0.028 0.204
Continuare pe pagina următoare / Continued on next page
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
7www.powerbelt.ro
Ø x Pasul filetului Ø x Lead
D4H
(mm)
D27 H
(mm)
D14 H
(mm) Începuturi de filet Thread starts
Joc radial Radial play
Joc axial Axial play
min min. max. min. max. min. max. min. max.
Tr 24 x 5 24.500 21.500 21.900 19.000 19.450 1 0.106 0.806 0.028 0.216
Tr 24 x 10 (P5) 24.500 21.500 21.900 19.000 19.450 2 0.106 0.806 0.028 0.216
Tr 25 x 3 25.500 23.500 23.835 22.000 22.315 1 0.085 0.670 0.023 0.180
Tr 25 x 5 25.500 22.500 22.900 20.000 20.450 1 0.106 0.806 0.028 0.216
Tr 25 x 10 (P5) 25.500 22.500 22.900 20.000 20.450 2 0.106 0.806 0.028 0.216
Tr 25 x 25 (P5) 25.500 22.500 22.900 20.000 20.450 5 0.106 0.806 0.028 0.216
Tr 26 x 5 26.500 23.500 23.900 21.000 21.450 1 0.106 0.806 0.028 0.216
Tr 26 x 10 (P5) 26.500 23.500 23.900 21.000 21.450 2 0.106 0.806 0.028 0.216
Tr 28 x 5 28.500 25.500 25.900 23.000 23.450 1 0.106 0.806 0.028 0.216
Tr 28 x 10 (P5) 28.500 25.500 25.900 23.000 23.450 2 0.106 0.806 0.028 0.216
Tr 30 x 3 30.500 28.500 28.835 27.000 27.315 1 0.085 0.670 0.023 0.180
Tr 30 x 4 30.500 28.000 28.855 26.000 26.375 1 0.095 1.215 0.025 0.326
Tr 30 x 5 30.500 27.500 27.900 25.000 25.450 1 0.106 0.806 0.028 0.216
Tr 30 x 6 31.000 27.000 27.450 24.000 24.500 1 0.118 0.903 0.032 0.242
Tr 30x12 (P6) 31.000 27.000 27.450 24.000 24.500 2 0.118 0.903 0.032 0.242
Tr 30 x 30 (P5) 30.500 27.500 27.900 25.000 25.450 6 0.106 0.806 0.028 0.216
Tr 32 x 6 33.000 29.000 29.450 26.000 26.500 1 0.118 0.903 0.032 0.242
Tr 32 x 12 (P6) 33.000 29.000 29.450 26.000 26.500 2 0.118 0.903 0.032 0.242
Tr 35 x 3 35.500 33.500 33.835 32.000 32.315 1 0.085 0.670 0.023 0.180
Tr 35 x 4 35.500 33.000 33.355 31.000 31.375 1 0.095 0.715 0.025 0.192
Tr 35 x 5 25.500 32.500 32.900 30.000 30.450 1 0.106 0.806 0.028 0.216
Tr 35 x 6 36.000 32.000 32.450 29.000 29.500 1 0.118 0.903 0.032 0.242
Tr 35 x 8 36.000 31.000 31.500 27.000 27.630 1 0.132 1.007 0.035 0.270
Tr 36 x 6 37.000 33.000 33.450 30.000 30.500 1 0.118 0.903 0.032 0.242
Tr 36 x 12 (P6) 37.000 33.000 33.450 30.000 30.500 2 0.118 0.903 0.032 0.242
Tr 40 x 3 40.500 38.500 38.835 37.000 37.315 1 0.085 0.670 0.023 0.180
Tr 40 x 4 40.500 38.000 38.355 36.000 36.375 1 0.095 0.715 0.025 0.192
Tr 40 x 5 40.500 37.500 37.900 35.000 35.450 1 0.106 0.806 0.028 0.216
Tr 40 x 6 41.000 37.000 37.450 34.000 34.500 1 0.118 0.903 0.032 0.242
Tr 40 x 7 41.000 36.500 36.975 33.000 33.560 1 0.125 0.955 0.033 0.256
Tr 40 x 8 41.000 36.000 36.500 32.000 32.630 1 0.132 1.007 0.035 0.270
Tr 40 x 10 41.000 35.000 35.530 30.000 30.710 1 0.150 1.080 0.040 0.289
Tr 40 x 14 (P7) 41.000 36.500 36.975 33.000 33.560 2 0.125 0.955 0.033 0.256
Tr 40 x 40 (P8) 41.000 36.000 36.500 32.000 32.630 5 0.132 1.007 0.035 0.270
Tr 44 x 7 45.000 40.500 40.975 37.000 37.560 1 0.125 0.955 0.033 0.256
Continuare pe pagina următoare / Continued on next page
Producătorul articolelor / Producer of the items:8 www.powerbelt.ro
Ø x Pasul filetului Ø x Lead
D4H
(mm)
D27 H
(mm)
D14 H
(mm) Începuturi de filet Thread starts
Joc radial Radial play
Joc axial Axial play
min min. max. min. max. min. max. min. max.
Tr 45 x 8 46.000 41.000 41.500 37.000 37.630 1 0.132 1.007 0.035 0.270
Tr 50 x 3 50.500 48.500 48.855 47.000 47.315 1 0.085 0.705 0.023 0.189
Tr 50 x 4 50.500 48.000 48.400 46.000 46.375 1 0.095 0.795 0.025 0.213
Tr 50 x 5 50.500 47.500 47.900 45.000 45.450 1 0.106 0.806 0.028 0.216
Tr 50 x 6 51.000 47.000 47.450 44.000 44.500 1 0.118 0.903 0.032 0.242
Tr 50 x 8 51.000 46.000 46.530 42.000 42.630 1 0.132 1.062 0.035 0.285
Tr 50 x 10 51.000 45.000 45.560 40.000 40.710 1 0.150 1.135 0.040 0.304
Tr 55 x 9 56.000 50.500 51.060 46.000 46.670 1 0.140 1.125 0.038 0.301
Tr 60 x 6 61.000 57.000 57.450 54.000 54.500 1 0.118 0.903 0.032 0.242
Tr 60 x 7 61.000 56.500 56.975 53.000 53.560 1 0.125 0.955 0.033 0.256
Tr 60 x 9 61.000 55.500 56.060 51.000 51.670 1 0.140 1.125 0.038 0.301
Tr 70 x 10 71.000 65.000 65.560 60.000 60.710 1 0.150 1.135 0.040 0.304
Tr 80 x 10 81.000 75.000 75.560 70.000 70.710 1 0.150 1.135 0.040 0.304
Tr 90 x 12 91.000 84.000 84.630 78.000 78.800 1 0.170 1.295 0.046 0.347
Tr 95 x 16 97.00 87.000 87.750 79.000 80.000 1 0,19 1.500 0.051 0.402
Tr 100 x 12 101.000 94.000 94.670 88.000 88.800 1 0.170 1.340 0.046 0.359
Tr 100 x 16 102.000 92.000 92.750 84.000 85.000 1 0.190 1.500 0.051 0.402
Tr 120 x 14 122.000 113.000 113.710 106.00 106.900 1 0.180 1.420 0.048 0.380
Tr 120 x 16 122.000 112.000 112.750 104.00 105.000 1 0.190 1.500 0.051 0.402
Tr 140 x 14 142.000 133.000 133.710 126.00 126.900 1 0.180 1.420 0.048 0.380
Tr 160 x 16 162.000 152.000 152.750 144.00 145.000 1 0.190 1.500 0.051 0.402
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
9www.powerbelt.ro
Sarcina axială criticăÎn cazul șuruburilor încărcate, este necesar să se evite sar-cina maximă din cauza încovoierii șurubului Sarcina axială admisibilă depinde de diametrul interior (d3) al șurubului, lagărele de capăt (rulmenți) și lungimea liberă (le) În ceea ce privește valorile date în grafic, luați un factor de siguran-ță minim ≥ 2
Critical axial loadIn case of loaded screws, it is necessary to avoid the peak load because of the screw bending Admissible axial load depends on the core diameter (d3) of the screw,end con-straints (bearings) and free length (le) Regarding the values given in the graph, allow a minimum safety factor ≥ 2
Graficul 1. Sarcina axială critică / Graph 1. Critical axial load
Exemplu: găsiți sarcina axială admisibilă a unui șurub Tr 30x6 de 3000 mm lungime, cu condiții de fixare ca în dia-grama 1 Luați F
max = 11 kN cu factor de siguranță 2 și presu-
puneți Fadm = 11/2 = 5,5 kN
Example: find the admissible axial load of a Tr 30x6 screw 3000 mm long with constraint conditions as in diagram1 Take F
max = 11 kN with safety factor of 2 and assume
Fadm = 11/2 = 5 5 kN
Turația criticăNumărul de rotații pe minut / turația critică reprezintă viteza de rotație la care apar vibrațiile în șurub Această vi-teză de rotație nu trebuie să fie atinsă niciodată, pentru că vibrațiile cauzează neregularități de funcționare grave Tura-ția critică depinde de diametrul șurubului, lagărele de capăt (rulmenți), lungimea liberă „lg“ și de precizia de asamblare
Critical revolutionThe critical revolutions per minute is the rotating speed at which screw vibrations appear This rotation speed must never be reached because the vibrations cause serious operating irregularities Critical rpm depend on screw diameter, end constraints (bearings), free length „lg” and from the assembly accuracy
Producătorul articolelor / Producer of the items:10 www.powerbelt.ro
Tabelul 1. - Coeficientul de precizie de asamblare Table 1. - Assembly accuracy coefficient
Precizia de asamblare Assembly accuracy
Condiții Conditions
Coeficient de siguranță Safety coefficient
Precizie de asamblare bună: Good assembly accuracy: Cuzineți de lagăre și de rulmenți obținuți de la strung CNC pe o structură deja finisată.
Bearing and nut seats obtained from CNC lathe onto an already finished structure.1.3 - 1.6
Aliniere piuliță la șurub în intervalul de 0,05 mm Nut alignment to screw within 0,05mm
Precizie de asamblare medie: Average assembly accuracy:
Cuzineți de lagăre și de rulmenți prelucrați pe piese care sunt apoi asamblate împreună. Alinierile sunt verificate cu ceasuri comparatoare cu deosebită grijă după montare.
Bearing and nut seats processed on parts which are then assembled together. Alignments are checked by comparators with estreme care after mounting.
1.7 - 2.5Aliniere piuliță la șurub în intervalul de 0,10 mm Nut alignment to screw within 0,10mm
Precizie de asamblare scăzută: Low assembly accuracy:
Cuzineți de lagăre și de rulmenți prelucrați pe piese care sunt apoi asamblate sau sudate împreună. Alinierile sunt verificate cu ceasuri comparatoare după montare.
Bearing and nut seats processed on parts which are then assembled or weld-ed together. Alignments are checked by comparators after mounting.
2.6 - 4.5Aliniere piuliță la șurub în intervalul de 0,25 mm Nut alignment to screw within 0,25mm
Graficul 2. Turația critică / Graph 2. Critical revolution
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
11www.powerbelt.ro
Alegerea motoruluiEficiențăPrin eficiență se înțelege capacitatea unui sistem șurub și piuliță de a transforma mișcarea de rotație în mișcare recti-linie Acest parametru permite să se evalueze câtă energie de rotație este transformată în energie utilă pentru deplasa-rea liniară, și de aici câtă energie este disipată sub formă de căldură Următoarea formulă se poate utiliza pentru calcul
Motor selectionEfficiencyBy efficiency is meant the ability of a screw & nut system to convert rotary motion into rectilinear motion This parameter allows appraisal of how much rotation energy is converted into useful energy for linear movement, hence how much energy is dissipated as heat The following formula can be used for calculation
Unghiul de înclinare / Lead angle
Efici
ență
/ Effi
cien
cy
ŋ:
ƒ:
α:
eficiență
factorul de frecare dinamică între materialele șurubului și piuliței
unghiul de înclinare a elicei filetului
efficiency
dynamic friction factor between screw and nut materials
lead angle of threads
Cuplul de torsiuneCuplul de torsiune necesar pentru deplasarea unui sistem șurub și piuliță se calculează prin următoarea ecuație:
TorqueThe Torque necessary for moving a screw & nut system is calculated by the following equation
C = F • P / 2π • η • 1000
C: Cuplul de torsiune Torque (input) [Nm]
F: Forța axială pe piuliță Axial force on nut [N]
P: Pasul real al șurubului True lead of screw [mm]
η: Eficiența Efficiency
Exemplu de calcul: Aflați cuplul necesar pentru deplasarea unui șurub Tr 30x6 cuplat cu o piuliță Tr 30x6
Example of calculation: Find torque necessary for move-ment of a screw Tr 30x6 coupled with a nut Tr 30x6
Rezistența la forță: Axial force resistance: 10 000 N Pasul șurubului: Screw lead: 6 mm η Eficiența: Efficiency: 0,26
C = F • P / (2π • η • 1000) = 10 000 • 6 / (2π • 0,26 • 1000) = 36,7 Nm
Producătorul articolelor / Producer of the items:12 www.powerbelt.ro
Valoarea cuplului nu ia în considerare eficiența pieselor me-canice care se deplasează împreună cu sistemul cu șurub, cum ar fi rulmenți, curele și alte componente de transmisie În faza de proiect, se recomandă o creștere între 20 și 30% din valoarea teoretică În cazul în care se utilizează motoare electrice cu un cuplu static redus, aplicați încă o creștere de 50% pentru a găsi cuplul nominal
The torque value does not consider the efficiency of mechanical parts moving together with the screw system, such as bearings, belts or other transmission components In project phase, an increase between the 20 and 30% of the theoretical value is recommended If electric motors with low static torque are used assume another increase of 50% to find nominal torque
Ceff = 36,7 Nm • 1,3 • 1,5 = 71,6 Nm
PutereaPuterea necesară pentru deplasarea unui sistem șurub și pi-uliță cu filet trapezoidal se calculează cu următoarea ecuație:
PowerThe power necessary for moving a trapezoidal screw & nut system is calculated with the following equation
P = (C • n) / 9550 P: Puterea Power [kW]
C: Cuplul de torsiune Torque [Nm]
n: Turația Rpm [1/min]
Exemplu de calcul: Calculați puterea necesară pentru depla-sarea șurubului Tr 30x6 din exemplul de mai sus la 600 rpm
Example of calculation: Calculate the power necessary for moving the screw Tr 30x6 of the above example at 600 rpm
P = (C • n) / 9550 = (71,6 • 600) / 9550 = 4,5 kW
tAceasta este puterea utilă minimă necesară!
This is the minimum useful power necessary
Instrucțiuni de utilizareDeplasare mecanizatăFurnizorul nostru are o grijă deosebită în ceea ce privește rectiliniaritatea acestor tipuri de șuruburi în timpul produc-ției A se vedea explicația toleranțelor de rectiliniaritate la pagina 4; aceasta se găsește ca valoare Δƒ în fișa de date a șurubului respectiv Aceste tipuri de șuruburi se pot utiliza la lungimea de 2-3 metri fără nici o încovoiere, sau cu o în-covoiere foarte mică, în funcție de lungimea șurubului
Deplasare manualăFurnizorul nostru nu are o grijă deosebită în ceea ce priveș-te rectiliniaritatea acestor tipuri de șuruburi în timpul pro-ducției, prin urmare, suntem în măsură să oferim un preț bun pentru aceste produse Cunoscând acest lucru, lungi-mea adecvată care trebuie luată în considerare a acestor șuruburi este de max 200-300 mm, cu o deplasare meca-nizată sau manuală lentă, sau aceasta poate fi mai lungă, în cazul în care șurubul nu ar fi folosit foarte des
User instructionMotorical movementOur supplier takes a special care about the straigthness of these type of screws during the production The explanation of straightness tolerances see on page 4 , it can be find as value Δƒ in the data sheet of the actual screw These type of screws can be used in 2-3 meters length without any bending, or with a very small bending, depending on the length of the screw
Manual movementOur supplier doesn’t take a special care about the straigth-ness of these type of screws during the production, there-fore we are able to offer a good price for these products Knowing this, the considerable suitable length of these screws max 200-300mm with a slow motorical or manual movement, or it can be longer if the screw would be used not so often
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
13www.powerbelt.ro
Tabel de prezentare generală a șuruburilor cu filet trapezoidal cu un singur început Single start trapezoidal screws overview table
Material Material C45 C15 Inox A2 Inox A4
Aplicație Application
Acționare automată
For motorical movement
Acționare manuală
For manual movement
Acționare automată
For motorical movement
Acționare automată
For motorical movement
Acționare manuală
For manual movement
Acționare automată
For motorical movement
Acționare manuală
For manual movement
Acționare manuală
For manual movement
Precizia pasului filetului
Lead accuracy100 μm / 300 mm 100 μm / 300 mm 50 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Pagina Page number 28 24 31 26 30 32 34 33
Tip de șurub Screw type KTS (79.006) KUE (79.007) KKA (79.003) KQX (79.004) KEQ (79.002) KRP (79.005) KRE (79.009) KAM (79.008)
Tr 10 x 2
Tr 10 x 3
Tr 12 x 3
Tr 14 x 3
Tr 14 x 4
Tr 16 x 4
Tr 18 x 4
Tr 20 x 4
Tr 22 x 5
Tr 24 x 5
Tr 25 x 3
Tr 25 x 5
Tr 26 x 5
Tr 28 x 5
Tr 30 x 3
Tr 30 x 4
Tr 30 x 5
Tr 30 x 6
Tr 32 x 6
Tr 35 x 3
Tr 35 x 4
Tr 35 x 5
Tr 35 x 6
Tr 35 x 8
Tr 36 x 6
Tr 40 x 3
Tr 40 x 4
Tr 40 x 5
Tr 40 x 6
Tr 40 x 7
Continuare pe pagina următoare / Continued on next page
Producătorul articolelor / Producer of the items:14 www.powerbelt.ro
Material Material C45 C15 Inox A2 Inox A4
Aplicație Application
Acționare automată
For motorical movement
Acționare manuală
For manual movement
Acționare automată
For motorical movement
Acționare automată
For motorical movement
Acționare manuală
For manual movement
Acționare automată
For motorical movement
Acționare manuală
For manual movement
Acționare manuală
For manual movement
Precizia pasului filetului
Lead accuracy100 μm / 300 mm 100 μm / 300 mm 50 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Pagina Page number 28 24 31 26 30 32 34 33
Tip de șurub Screw type KTS (79.006) KUE (79.007) KKA (79.003) KQX (79.004) KEQ (79.002) KRP (79.005) KRE (79.009) KAM (79.008)
Tr 40 x 8
Tr 40 x 10
Tr 44 x 7
Tr 45 x 8
Tr 50 x 3
Tr 50 x 4
Tr 50 x 5
Tr 50 x 6
Tr 50 x 8
Tr 50 x 10
Tr 55 x 9
Tr 60 x 6
Tr 60 x 7
Tr 60 x 9
Tr 70 x 10
Tr 80 x 10
Tr 90 x 12
Tr 95 x 16
Tr100 x 12
Tr100 x 16
Tr120 x 14
Tr120 x 16
Tr140 x 14
produse din stoc sau diponibile la furnizor goods in stock or available solicitare cantitate minimă, produse disponibile cu timp de livrare mai lung minimum quantity request, good available with long delivery time
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
15www.powerbelt.ro
Tabel de prezentare generală a șuruburilor cu filet trapezoidal cu mai multe începuturi Multiple start trapezoidal screws overview table
Material Material C45 C15 Inox A2
Aplicație Application
Acționare automată For motorical movement
Acționare manuală For manual movement
Acționare automată For motorical movement
Acționare automată For motorical movement
Acționare manuală For manual movement
Precizia pasului filetului Lead accuracy 100 μm / 300 mm 100 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm 200 μm / 300 mm
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Pagina Page number 28 24 26 32 34
Tip de șurub Screw type KTS (79.006) KUE (79.007) KQX (79.004) KRP (79.005) KRE (79.009)
Tr 10 x 4 (P2)
Tr 12 x 6 (P3)
Tr 14 x 6 (P3)
Tr 16 x 8 (P4)
Tr 18 x 8 (P4)
Tr 20 x 8 (P4)
Tr 20 x 20 (P5)
Tr 22 x 10 (P5)
Tr 24 x 10 (P5)
Tr 25 x 10 (P5)
Tr 25 x 25 (P5)
Tr 26 x 10 (P5)
Tr 28 x 10 (P5)
Tr 30 x 12 (P6)
Tr 30 x 30 (P5)
Tr 32 x 12 (P6)
Tr 36 x 12 (P6)
Tr 40 x 14 (P7)
Tr 40 x 40 (P8)
produse din stoc sau diponibile la furnizor goods in stock or available solicitare cantitate minimă, produse disponibile cu timp de livrare mai lung minimum quantity request, good available with long delivery time
Producătorul articolelor / Producer of the items:16 www.powerbelt.ro
Tabel de prezentare generală piulițe cilindrice cu filet trapezoidal Cylindrical trapezoidal nuts overview table
Material Material
Oțel / steel 11SMnPb37
Oțel / steel 11SMn30
Oțel inoxidabil Stainless steel Aisi 303 1.4305
Bronz / bronze CuSn5Zn5Pb5-C
Bronz / bronze CuSn7Zn4Pb7-C
Bronz / bronze CuSn12-C
Imagine Picture
Pagina Page number 37 37 43 38 38 48
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Tipul piuliței Nut type MLF (79.021) MZP (79.010) HDA (79.014) HSN (79.012) HBD (79.022) BIG (79.020)
Tr 10 x 2
Tr 10 x 3
Tr 12 x 3
Tr 14 x 3
Tr 14 x 4
Tr 16 x 4
Tr 18 x 4
Tr 20 x 4
Tr 22 x 5
Tr 24 x 5
Tr 25 x 3
Tr 25 x 5
Tr 26 x 5
Tr 28 x 5
Tr 30 x 3
Tr 30 x 4
Tr 30 x 5
Tr 30 x 6
Tr 32 x 6
Tr 35 x 3
Tr 35 x 4
Tr 35 x 5
Tr 35 x 6
Tr 35 x 8
Tr 36 x 6
Tr 40 x 3
Tr 40 x 4
Tr 40 x 5
Tr 40 x 6
Continuare pe pagina următoare / Continued on next page
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
17www.powerbelt.ro
Material Material
Oțel / steel 11SMnPb37
Oțel / steel 11SMn30
Oțel inoxidabil Stainless steel Aisi 303 1.4305
Bronz / bronze CuSn5Zn5Pb5-C
Bronz / bronze CuSn7Zn4Pb7-C
Bronz / bronze CuSn12-C
Imagine Picture
Pagina Page number 37 37 43 38 38 48
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Tipul piuliței Nut type MLF (79.021) MZP (79.010) HDA (79.014) HSN (79.012) HBD (79.022) BIG (79.020)
Tr 40 x 7
Tr 40 x 8
Tr 40 x 10
Tr 44 x 7
Tr 45 x 8
Tr 50 x 3
Tr 50 x 4
Tr 50 x 5
Tr 50 x 6
Tr 50 x 8
Tr 50 x 10
Tr 55 x 9
Tr 60 x 6
Tr 60 x 7
Tr 60 x 9
Tr 70 x 10
Tr 80 x 10
produse din stoc sau diponibile la furnizor goods in stock or available
Producătorul articolelor / Producer of the items:18 www.powerbelt.ro
Tabel I. de prezentare generală a altor tipuri de șuruburi și piulițe cu filet trapezoidal Other shape of trapezoidal nuts overview table I.
Material Material
Oțel / Steel 11SMnPb37
Alamă / Brass CW614N-M
Bronz / Bronze CuSn5Zn5Pb5-C
Bronz / Bronze CuSn12-C
Bronz / Bronze CuSn12-C
Imagine Picture
Pagina Page number 46 47 40 40 42
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Tipul piuliței Nut type CQA (79.018) QOB (79.019) FTN (79.015) FXN (79.023) HDL (79.011)
Tr 10 x 2
Tr 10 x 3
Tr 12 x 3
Tr 14 x 3
Tr 14 x 4
Tr 16 x 4
Tr 18 x 4
Tr 20 x 4
Tr 22 x 5
Tr 24 x 5
Tr 25 x 3
Tr 25 x 5
Tr 26 x 5
Tr 28 x 5
Tr 30 x 3
Tr 30 x 4
Tr 30 x 5
Tr 30 x 6
Tr 32 x 6
Tr 35 x 3
Tr 35 x 4
Tr 35 x 5
Tr 35 x 6
Tr 35 x 8
Tr 36 x 6
Tr 40 x 3
Tr 40 x 4
Tr 40 x 5
Tr 40 x 6
Tr 40 x 7
Continuare pe pagina următoare / Continued on next page
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
19www.powerbelt.ro
Material Material
Oțel / Steel 11SMnPb37
Alamă / Brass CW614N-M
Bronz / Bronze CuSn5Zn5Pb5-C
Bronz / Bronze CuSn12-C
Bronz / Bronze CuSn12-C
Imagine Picture
Pagina Page number 46 47 40 40 42
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Tipul piuliței Nut type CQA (79.018) QOB (79.019) FTN (79.015) FXN (79.023) HDL (79.011)
Tr 40 x 8
Tr 40 x 10
Tr 44 x 7
Tr 45 x 8
Tr 50 x 3
Tr 50 x 4
Tr 50 x 5
Tr 50 x 6
Tr 50 x 8
Tr 50 x 10
Tr 55 x 9
Tr 60 x 6
Tr 60 x 7
Tr 60 x 9
produse din stoc sau diponibile la furnizor goods in stock or available
Producătorul articolelor / Producer of the items:20 www.powerbelt.ro
Tabel II. de prezentare generală a altor tipuri de șuruburi și piulițe cu filet trapezoidal Other shape of trapezoidal nuts overview table II.
Material Material
Bronz / bronze CuSn5Zn5Pb5-C
Oțel / steel 11SMnPb37
Plastic / plastic PA6+MoS2
Plastic / plastic PA6+MoS2
Imagine Picture
Pagina Page number 40 36 45 44
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Tipul piuliței Nut type FFR (79.024) MES (79.013) FCS (79.017) MPH (79.016)
Tr 10 x 2
Tr 10 x 3
Tr 12 x 3
Tr 14 x 3
Tr 14 x 4
Tr 16 x 4
Tr 18 x 4
Tr 20 x 4
Tr 22 x 5
Tr 24 x 5
Tr 25 x 3
Tr 25 x 5
Tr 26 x 5
Tr 28 x 5
Tr 30 x 3
Tr 30 x 4
Tr 30 x 5
Tr 30 x 6
Tr 32 x 6
Tr 35 x 3
Tr 35 x 4
Tr 35 x 5
Tr 35 x 6
Tr 35 x 8
Tr 36 x 6
Tr 40 x 3
Tr 40 x 4
Tr 40 x 5
Tr 40 x 6
Tr 40 x 7
Tr 40 x 8
Continuare pe pagina următoare / Continued on next page
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
21www.powerbelt.ro
Material Material
Bronz / bronze CuSn5Zn5Pb5-C
Oțel / steel 11SMnPb37
Plastic / plastic PA6+MoS2
Plastic / plastic PA6+MoS2
Imagine Picture
Pagina Page number 40 36 45 44
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Tipul piuliței Nut type FFR (79.024) MES (79.013) FCS (79.017) MPH (79.016)
Tr 40 x 10
Tr 44 x 7
Tr 45 x 8
Tr 50 x 3
Tr 50 x 4
Tr 50 x 5
Tr 50 x 6
Tr 50 x 8
Tr 50 x 10
Tr 55 x 9
Tr 60 x 6
Tr 60 x 7
Tr 60 x 9
Tr 70 x 10
produse din stoc sau diponibile la furnizor goods in stock or available
Producătorul articolelor / Producer of the items:22 www.powerbelt.ro
Tabel I. de prezentare generală piulițe cu filet trapezoidal cu mai multe începuturi. Multiple start trapezoidal nuts overview table I.
Material Material
Oțel / steel 11SMnPb37
Oțel / steel 11SMn30
Bronz / bronze CuSn5Zn5Pb5-C
Bronz / bronze CuSn7Zn4Pb7-C
Bronz / bronze CuSn12-C
Imagine Picture
Pagina Page number 37 37 38 38 40
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Tipul piuliței Nut type MLF (79.021) MZP (79.010) HSN (79.012) HBD (79.022) FXN (79.023)
Tr 10 x 4 (P2)
Tr 12 x 6 (P3)
Tr 14 x 6 (P3)
Tr 16 x 8 (P4)
Tr 18 x 8 (P4)
Tr 20 x 8 (P4)
Tr 20 x 20 (P5)
Tr 22 x 10 (P5)
Tr 24 x 10 (P5)
Tr 25 x 10 (P5)
Tr 25 x 25 (P5)
Tr 26 x 10 (P5)
Tr 28 x 10 (P5)
Tr 30 x 12 (P6)
Tr 30 x 30 (P5)
Tr 32 x 12 (P6)
Tr 36 x 12 (P6)
Tr 40 x 14 (P7)
Tr 40 x 40 (P8)
produse din stoc sau diponibile la furnizor goods in stock or available
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
23www.powerbelt.ro
Tabel II. de prezentare generală piulițe cu filet trapezoidal cu mai multe începuturi. Multiple start trapezoidal nuts overview table II.
Material Material
Bronz / bronze CuSn12-C
Bronz / bronze CuSn5Zn5Pb5-C
Plastic / plastic PA6+MoS2
Plastic / plastic PA6+MoS2
Imagine Picture
Pagina Page number 42 40 45 44
Elicea filetului Helix
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
dreapta right
stânga left
Tipul piuliței Nut type HDL (79.011) FFR (79.024) FCS (79.017) MPH (79.016)
Tr 10 x 4 (P2)
Tr 12 x 6 (P3)
Tr 14 x 6 (P3)
Tr 16 x 8 (P4)
Tr 18 x 8 (P4)
Tr 20 x 8 (P4)
Tr 20 x 20 (P5)
Tr 22 x 10 (P5)
Tr 24 x 10 (P5)
Tr 25 x 10 (P5)
Tr 25 x 25 (P5)
Tr 26 x 10 (P5)
Tr 28 x 10 (P5)
Tr 30 x 12 (P6)
Tr 30 x 30 (P5)
Tr 32 x 12 (P6)
Tr 36 x 12 (P6)
Tr 40 x 14 (P7)
Tr 40 x 40 (P8)
produse din stoc sau diponibile la furnizor goods in stock or available
Producătorul articolelor / Producer of the items:24 www.powerbelt.ro
ȘURUBURI CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREWS
TIP KUE (79.007) KUE (79.007) TYPE
Penru acționare manuală For manual movement
Material Material
C45 oțel (1.0503) C45 steel (1.0503)
Toleranță Tolerance
100 µm / 300 mm
Duritatea suprafeței Surface hardness
250 HB
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul de încl. al elicei
Lead angle
Moment de inerție Moment of inertia
(mm4)
Greu-tate
Weight (kg/m)
Tip de șurub Screw type
Dreapta Right
Stânga Left d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m L=1m L=2m L=3m
79.007. _ _ 009 010 - 007 008 - Tr 10x2 1 0.5 / 300 9,828 10 8,739 8,929 7,191 7,5 4°02’ 131 0,48
79.007. _ _ 003 004 - 001 002 - Tr 10x3 1 0.5 / 300 9,764 10 8,203 8,415 6,150 6,5 6°25’ 70 0,42
79.007. _ _ 005 006 - - - - Tr 10x4 (P2) 2 0.5 / 300 9,82 10 8,716 8,929 7,191 7,5 8°03’ 131 0,48
79.007. _ _ 014 015 016 011 012 013 Tr 12x3 1 0.5 / 300 11,764 12 10,191 10,415 8,135 8,5 5°12’ 215 0,65
79.007. _ _ 017 018 019 - - - Tr 12x6 (P3) 2 0.5 / 300 11,764 12 10,191 10,415 8,135 8,5 10°19’ 215 0,65
79.007. _ _ 032 033 034 029 030 031 Tr 14x3 1 0.5 / 300 13,764 14 12,191 12,415 10,135 10,5 4°22’ 518 0,93
79.007. _ _ 023 024 025 020 021 022 Tr 14x4 1 0.5 / 300 13,700 14 11,640 11,905 9,074 9,5 6°03’ 333 0,86
79.007. _ _ 026 027 028 - - - Tr 14x6 (P3) 2 0.5 / 300 13,764 14 12,164 12,415 10,135 10,5 8°41’ 518 0,93
79.007. _ _ 038 039 040 035 036 037 Tr 16x4 1 0.5 / 300 15,700 16 13,640 13,905 11,074 11,5 5°12’ 738 1,17
79.007. _ _ 041 042 043 - - - Tr 16x8 (P4) 2 0.5 / 300 15,700 16 13,640 13,905 11,074 11,5 10°19’ 738 1,17
79.007. _ _ 047 048 049 044 045 046 Tr 18x4 1 0.5 / 300 17,700 18 15,640 15,905 13,074 13,5 4°33’ 1434 1,53
79.007. _ _ 050 051 052 - - - Tr 18x8 (P4) 2 0.5 / 300 17,700 18 15,608 15,905 13,074 13,5 9°02’ 1434 1,53
79.007. _ _ 056 057 058 053 054 055 Tr 20x4 1 0.5 / 300 19,700 20 17,640 17,905 15,074 15,5 4°03’ 2534 1,94
79.007. _ _ 059 060 061 - - - Tr 20x8 (P4) 2 0.5 / 300 19,700 20 17,640 17,905 15,074 15,5 8°03’ 2534 1,94
79.007. _ _ 068 069 070 065 066 067 Tr 22x5 1 0.2 / 300 21,665 22 19,114 19,394 16,044 16,5 4°40’ 3232 2,29
79.007. _ _ 071 072 073 - - - Tr 22x10 (P5) 2 0.3 / 300 21,665 22 19,080 19,394 16,044 16,5 9°16’ 3232 2,29
79.007. _ _ 077 078 079 074 075 076 Tr 24x5 1 0.2 / 300 23,665 24 21,094 21,394 18,019 18,5 4°14’ 5175 2,78
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
25www.powerbelt.ro
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul de încl. al elicei
Lead angle
Moment de inerție Moment of inertia
(mm4)
Greu-tate
Weight (kg/m)
Tip de șurub Screw type
Dreapta Right
Stânga Left d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m L=1m L=2m L=3m
79.007. _ _ 080 081 082 - - - Tr 24x10 (P5) 2 0.3 / 300 23,665 24 21,058 21,394 18,019 18,5 8°25’ 5175 2,78
79.007. _ _ 095 096 097 - - - Tr 25x3 1 0.2 / 300 24,764 25 23,165 23,415 21,103 21,5 2°20’ 9735 3,30
79.007. _ _ 086 087 088 083 084 085 Tr 25x5 1 0.2 / 300 24,665 25 22,094 22,394 19,019 19,5 4°03’ 6423 3,05
79.007. _ _ 092 093 094 - - - Tr 25x25 (P5) 5 0.3 / 300 24,665 25 22,094 22,394 19,019 19,5 19°30’ 6423 3,05
79.007. _ _ 101 102 103 098 099 100 Tr 26x5 1 0.2 / 300 25,665 26 23,094 23,394 20,019 20,5 3°52’ 7884 3,33
79.007. _ _ 104 105 106 - - - Tr 26x10 (P5) 2 0.3 / 300 25,665 26 23,094 23,394 20,019 20,5 7°42’ 7884 3,33
79.007. _ _ 110 111 112 107 108 109 Tr 28x5 1 0.2 / 300 27,665 28 25,094 25,394 22,019 22,5 3°34’ 11539 3,92
79.007. _ _ 113 114 115 - - - Tr 28x10 (P5) 2 0.3 / 300 27,665 28 25,094 25,394 22,019 22,5 7°07’ 11539 3,92
79.007. _ _ 135 136 137 132 133 134 Tr 30x6 1 0.2 / 300 29,625 30 26,547 26,882 22,463 23,0 4°03’ 13650 4,38
79.007. _ _ 138 139 140 - - - Tr 30x12 (P6) 2 0.3 / 300 29,625 30 26,547 26,882 22,463 23,0 8°03’ 13650 4,38
79.007. _ _ 147 148 149 144 145 146 Tr 32x6 1 0.2 / 300 31,625 32 28,547 28,882 24,463 25,0 3°46’ 17580 5,06
79.007. _ _ 150 151 152 - - - Tr 32x12 (P6) 2 0.3 / 300 31,625 32 28,547 28,882 24,463 25,0 7°30’ 17580 5,06
79.007. _ _ 174 175 176 171 172 173 Tr 35x6 1 0.2 / 300 34,625 35 31,547 31,882 27,463 28,0 3°25’ 30000 6,16
79.007. _ _ 177 178 179 - - - Tr 35x8 1 0.2 / 300 34,550 35 30,493 30,868 25,399 26,0 4°42’ 21980 5,85
79.007. _ _ 183 184 185 180 181 182 Tr 36x6 1 0.2 / 300 35,625 36 32,547 32,882 28,463 29,0 3°19’ 34540 6,56
79.007. _ _ 186 187 188 - - - Tr 36x12 (P6) 2 0.3 / 300 35,625 36 32,547 32,882 28,463 29,0 6°36’ 34540 6,56
79.007. _ _ 225 226 227 189 190 191 Tr 40x6 1 0.2 / 300 39,625 40 36,547 36,882 32,463 33,0 2°57’ 57950 8,26
79.007. _ _ 210 211 212 207 208 209 Tr 40x7 1 0.2 / 300 39,575 40 36,020 36,375 31,431 32,0 3°30’ 51030 8,03
79.007. _ _ 222 223 224 - - - Tr 40x8 1 0.2 / 300 39,550 40 35,493 35,868 30,399 31,0 4°03’ 44560 7,90
79.007. _ _ 219 220 221 - - - Tr 40x10 1 0.2 / 300 39,470 40 34,450 34,850 28,350 29,0 5°12’ 31700 7,49
79.007. _ _ 213 214 215 - - - Tr 40x14 (P7) 2 0.3 / 300 39,575 40 36,020 36,375 31,431 32,0 6°58’ 51300 8,03
79.007. _ _ 231 232 233 228 229 230 Tr 44x7 1 0.2 / 300 43,575 44 40,020 40,375 35,431 36,0 3°09’ 81820 9,90
79.007. _ _ 237 238 239 234 235 236 Tr 45x8 1 0.2 / 300 44,550 45 40,493 40,868 35,399 36,0 3°33’ 81245 10,23
79.007. _ _ 261 262 263 258 259 260 Tr 50x8 1 0.2 / 300 49,550 50 45,468 45,868 40,368 41,0 3°10’ 136930 12,90
79.007. _ _ 264 265 266 - - - Tr 50x10 1 0.2 / 300 49,470 50 44,425 44,850 38,319 39,0 4°03’ 150834 12,37
79.007. _ _ 267 268 269 - - - Tr 55x9 1 0.2 / 300 54,500 55 49,935 50,360 44,329 45,0 3°15’ 189550 15,51
79.007. _ _ 273 274 275 270 271 272 Tr 60x9 1 0.2 / 300 59,500 60 54,935 55,360 49,329 50,0 2°57’ 302600 18,74
79.007. _ _ 279 280 281 276 277 278 Tr 70x10 1 0.4 / 300 69,470 70 64,425 64,850 58,319 59,0 2°48’ 587540 25,80
79.007. _ _ 285 286 287 282 283 284 Tr 80x10 1 0.4 / 300 79,470 80 74,425 74,850 68,319 69,0 2°26’ 1069390 34,39
79.007. _ _ 288 289 290 - - - Tr 90x12 1 0.5 / 300 89,400 90 83,335 83,830 76,246 77,0 2°36’ 1658969 43,07
79.007. _ _ 291 292 293 - - - Tr 95x16 1 1 / 300 94,290 95 86,250 86,810 76,110 77,0 3°21’ 1647164 45,90
79.007. _ _ 294 295 296 - - - Tr 100x12 1 1 / 300 99,400 100 93,330 93,830 86,215 87,0 2°19’ 2712072 53,99
79.007. _ _ 297 298 299 - - - Tr 100x16 1 1 / 300 99,290 100 91,250 91,810 81,110 82,0 3°10’ 2124553 51,37
79.007. _ _ 300 301 302 - - - Tr 120x14 1 1 / 300 119,33 120 112,290 112,820 103,157 104,0 2°16’ 5558591 77,72
79.007. _ _ 303 304 305 - - - Tr 120x16 1 1 / 300 119,29 120 111,250 111,810 101,110 102,0 2°36’ 5130342 76,34
79.007. _ _ 306 307 308 - - - Tr 140x14 1 1 / 300 139,33 140 132,290 132,820 123,157 124,0 1°55’ 11292921 107,87
Producătorul articolelor / Producer of the items:26 www.powerbelt.ro
TIP KQX (79.004) KQX (79.004) TYPE
Pentru mișcări mecanice For motorical movement
Material Material
C15 oțel (1.1141) C15 steel (1.1141)
Toleranță Tolerance
200 µm / 300 mm
Duritatea suprafeței Surface hardness
160/180 HB
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul de încl. al elicei
Lead angle
Moment de inerție Moment of inertia
(mm4)
Greu-tate
Weight (kg/m)
Tip de șurub
Screw type
Dreapta Right
Stânga Left d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m L=1m L=2m L=3m
79.004. _ _ 003 004 - 001 002 - Tr 10x3 1 0.7 / 1000 9,764 10 8,203 8,415 7,191 7,5 4°02’ 70 0.42
79.004. _ _ 014 015 016 011 012 013 Tr 12x3 1 0.7 / 1000 11,764 12 10,191 10,415 8,135 8,5 5°12’ 215 0.65
79.004. _ _ 017 018 019 - - - Tr 12x6 (P3) 2 0.7 / 1000 11,764 12 10,191 10,415 8,135 8,5 10°19’ 215 0.65
79.004. _ _ 023 024 025 020 021 022 Tr 14x4 1 0.7 / 1000 13,700 14 11,640 11,905 9,074 9,5 6°03’ 333 0.86
79.004. _ _ 038 039 040 035 036 037 Tr 16x4 1 0.7 / 1500 15,700 16 13,640 13,905 11,074 11,5 5°12’ 738 1.17
79.004. _ _ 041 042 043 - - - Tr 16x8 (P4) 2 0.7 / 1500 15,700 16 13,640 13,905 11,074 11,5 10°19’ 738 1.17
79.004. _ _ 047 048 049 044 045 046 Tr 18x4 1 0.7 / 1500 17,700 18 15,640 15,905 13,074 13,5 4°33’ 1434 1.53
79.004. _ _ 056 057 058 053 054 055 Tr 20x4 1 0.6 / 2000 19,700 20 17,640 17,905 15,074 15,5 4°03’ 2534 1.94
79.004. _ _ 059 060 061 - - - Tr 20x8 (P4) 2 0.6 / 2000 19,700 20 17,640 17,905 15,074 15,5 8°03’ 2534 1.94
79.004. _ _ 062 063 064 - - - Tr 20x20 (P5) 4 0.6 / 2000 19,665 20 17,114 17,394 14,044 14,5 20°00’ 1910 1.84
79.004. _ _ 068 069 070 065 066 067 Tr 22x5 1 0.6 / 2000 21,665 22 19,114 19,394 16,044 16,5 4°40’ 3232 2.29
79.004. _ _ 077 078 079 074 075 076 Tr 24x5 1 0.4 / 2000 23,665 24 21,094 21,394 18,019 18,5 4°14’ 5175 2.79
79.004. _ _ 086 087 088 083 084 085 Tr 25x5 1 0.4 / 2000 24,665 25 22,094 22,394 19,019 19,5 4°03’ 6423 3.05
79.004. _ _ 089 090 091 - - - Tr 25x10 (P5) 2 0.4 / 2000 24,665 25 22,094 22,394 19,019 19,5 8°03’ 6423 3.05
79.004. _ _ 092 093 094 - - - Tr 25x25 (P5) 5 0.4 / 2000 24,665 25 22,094 22,394 19,019 19,5 19°30’ 6423 3.05
79.004. _ _ 101 102 103 098 099 100 Tr 26x5 1 0.4 / 2000 25,665 26 23,094 23,394 20,019 20,5 3°52’ 7884 3.33
79.004. _ _ 110 111 112 107 108 109 Tr 28x5 1 0.4 / 2000 27,665 28 25,094 25,394 22,019 22,5 3°34’ 11539 3.92
79.004. _ _ 113 114 115 - - - Tr 28x10 (P5) 2 0.4 / 2000 27,665 28 25,094 25,394 22,019 22,5 7°07’ 11539 3.92
79.004. _ _ 116 117 118 - - - Tr 30x3 1 0.4 / 3000 29,764 30 28,165 28,415 26,103 26,5 1°55’ 22900 4,88
79.004. _ _ 119 120 121 122 124 125 Tr 30x4 1 0.4 / 3000 29,700 30 27,640 27,905 25,074 25,5 2°36’ 19400 4,72
79.004. _ _ 126 127 128 129 130 131 Tr 30x5 1 0.4 / 3000 29,665 30 27,094 27,394 24,019 24,5 3°19’ 16340 4,57
79.004. _ _ 135 136 137 132 133 134 Tr 30x6 1 0.4 / 3000 29,625 30 26,547 26,882 22,463 23,0 4°03’ 13650 4.38
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
27www.powerbelt.ro
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul de încl. al elicei
Lead angle
Moment de inerție Moment of inertia
(mm4)
Greu-tate
Weight (kg/m)
Tip de șurub
Screw type
Dreapta Right
Stânga Left d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m L=1m L=2m L=3m
79.004. _ _ 138 139 140 - - - Tr 30x12 (P6) 2 0.4 / 3000 29,625 30 26,547 26,882 22,463 23,0 8°03’ 13650 4.38
79.004. _ _ 141 142 143 - - - Tr 30x30 (P5) 6 0.4 / 3000 29,665 30 27,094 27,394 24,019 24,5 19°09’ 16340 4.57
79.004. _ _ 147 148 149 144 145 146 Tr 32x6 1 0.4 / 3000 31,625 32 28,547 28,882 24,463 25,0 3°46’ 17580 5.06
79.004. _ _ 153 154 155 - - - Tr 35x3 1 0.4 / 3000 34,764 35 33,165 33,415 31,103 31,5 1°38’ 46128 6,77
79.004. _ _ 159 160 161 162 163 164 Tr 35x4 1 0.4 / 3000 34,700 35 32,640 32,905 30,074 30,5 2°13’ 40150 6,57
79.004. _ _ 165 166 167 168 169 170 Tr 35x5 1 0.4 / 3000 34,665 35 32,094 32,394 29,019 29,5 2°48’ 34810 6,40
79.004. _ _ 174 175 176 171 172 173 Tr 35x6 1 0.3 / 3000 34,625 35 31,547 31,882 27,463 28,0 3°25’ 30000 6,16
79.004. _ _ 183 184 185 180 181 182 Tr 36x6 1 0.3 / 3000 35,625 36 32,547 32,882 28,463 29,0 3°19’ 34540 6.56
79.004. _ _ 189 190 191 - - - Tr 40x3 1 0.4 / 3000 39,764 40 38,165 38,415 36,103 36,5 1°25’ 83395 8,95
79.004. _ _ 195 196 197 198 199 200 Tr 40x4 1 0.4 / 3000 39,700 40 37,640 37,905 35,074 35,5 1°55’ 74290 8,71
79.004. _ _ 201 202 203 204 205 206 Tr 40x5 1 0.4 / 3000 39,665 40 37,094 37,394 34,019 34,5 2°26’ 65740 8,51
79.004. _ _ 225 226 227 - - - Tr 40x6 1 0.4 / 3000 39,625 40 36,547 36,882 32,463 33,0 2°57’ 57950 5,26
79.004. _ _ 210 211 212 207 208 209 Tr 40x7 1 0.3 / 3000 39,575 40 36,020 36,375 31,431 32,0 3°30’ 51030 8.03
79.004. _ _ 213 214 215 - - - Tr 40x14 (P7) 2 0.3 / 3000 39,575 40 36,020 36,375 31,431 32,0 6°58’ 51300 8.03
79.004. _ _ 216 217 218 - - - Tr 40x40 (P8) 5 0.3 / 3000 39,550 40 35,493 35,868 30,399 31,0 19°30’ 44560 7.90
79.004. _ _ 231 232 233 228 229 230 Tr 44x7 1 0.3 / 3000 43,575 44 40,020 40,375 35,431 36,0 3°09’ 81820 9.90
79.004. _ _ 237 238 239 234 235 236 Tr 45x8 1 0.3 / 3000 44,550 45 40,493 40,868 35,399 36,0 3°33’ 81245 10.23
79.004. _ _ 240 241 242 - - - Tr 50x3 1 0.3 / 3000 49,764 50 48,150 48,415 46,084 46,5 1°08’ 121400 14,26
79.004. _ _ 246 247 248 249 250 251 Tr 50x4 1 0.3 / 3000 49,700 50 47,605 47,905 45,074 45,5 1°31’ 202600 13,96
79.004. _ _ 252 253 254 255 256 257 Tr 50x5 1 0.3 / 3000 49,665 50 47,094 47,394 44,019 44,5 1°55’ 184300 13,70
79.004. _ _ 246 247 248 249 250 251 Tr 50x6 1 0.3 / 3000 49,625 50 46,547 46,882 42,463 43,0 2°20’ 167240 13,35
79.004. _ _ 261 262 263 258 259 260 Tr 50x8 1 0.3 / 3000 49,550 50 45,468 45,868 40,368 41,0 3°10’ 136930 12.90
79.004. _ _ 264 265 266 - - - Tr 50x10 1 0.3 / 3000 49,470 50 44,425 44,850 38,319 39,0 4°03’ 150834 12,37
79.004. _ _ 267 268 269 - - - Tr 55x9 1 0.3 / 3000 54,500 55 49,935 50,360 44,329 45,0 3°15’ 189550 15.51
79.004. _ _ 309 311 313 315 317 319 Tr 60x6 1 0.3 / 3000 59,625 60 56,547 56,882 52,463 53,0 1°55’ 386240 19,67
79.004. _ _ 310 312 314 316 318 320 Tr 60x7 1 0.3 / 3000 59,575 60 56,020 56,375 51,431 52,0 2°16’ 343450 19,36
79.004. _ _ 273 274 275 270 271 272 Tr 60x9 1 0.3 / 3000 59,500 60 54,935 55,360 49,329 50,0 2°57’ 302600 18.74
79.004. _ _ 279 280 281 276 277 278 Tr 70x10 1 0.3 / 3000 69,470 70 64,425 64,850 58,319 59,0 2°48’ 587540 25.80
79.004. _ _ 285 286 287 282 283 284 Tr 80x10 1 0.3 / 3000 79,470 80 74,425 74,850 68,319 69,0 2°26’ 1069390 34.39
Producătorul articolelor / Producer of the items:28 www.powerbelt.ro
TIP KTS (79.006) KTS (79.006) TYPE
Pentru mișcări mecanice For motorical movement
Material Material
C45 oțel (1.0503) C45 steel (1.0503)
Toleranță Tolerance
100 µm / 300 mm
Duritatea suprafeței Surface hardness
250 HB
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul de încl. al elicei
Lead angle
Moment de inerție Moment of inertia
(mm4)
Greu-tate
Weight (kg/m)
Tip de șurub
Screw type
Dreapta Right
Stânga Left d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m L=1m L=2m L=3m
79.006. _ _ 009 010 - 007 008 - Tr 10x2 1 0.5 / 1000 9,828 10 8,739 8,929 7,191 7,5 4°02’ 131 0.48
79.006. _ _ 003 004 - 001 002 - Tr 10x3 1 0.5 / 1000 9,764 10 8,203 8,415 6,150 6,5 6°25’ 70 0.42
79.006. _ _ 005 006 - - - - Tr 10x4 (P2) 2 0.5 / 1000 9,820 10 8,716 8,929 7,191 7,5 8°03’ 131 0.48
79.006. _ _ 014 015 016 011 012 013 Tr 12x3 1 0.5 / 1000 11,764 12 10,191 10,415 8,135 8,5 5°12’ 215 0.65
79.006. _ _ 017 018 019 - - - Tr 12x6 (P3) 2 0.5 / 1000 11,764 12 10,191 10,415 8,135 8,5 10°19’ 215 0.65
79.006. _ _ 032 033 034 029 030 031 Tr 14x3 1 0.5 / 1000 13,764 14 12,191 12,415 10,135 10,5 4°22’ 518 0.93
79.006. _ _ 023 024 025 020 021 022 Tr 14x4 1 0.5 / 1000 13,700 14 11,640 11,905 9,074 9,5 6°03’ 333 0.86
79.006. _ _ 026 027 028 - - - Tr 14x6 (P3) 2 0.5 / 1000 13,764 14 12,164 12,415 10,135 10,5 8°41’ 518 0.93
79.006. _ _ 038 039 040 035 036 037 Tr 16x4 1 0.5 / 1000 15,700 16 13,640 13,905 11,074 11,5 5°12’ 738 1.17
79.006. _ _ 041 042 043 - - - Tr 16x8 (P4) 2 0.5 / 1000 15,700 16 13,640 13,905 11,074 11,5 10°19’ 738 1.17
79.006. _ _ 047 048 049 044 045 046 Tr 18x4 1 0.5 / 1000 17,700 18 15,640 15,905 13,074 13,5 4°33’ 1434 1.53
79.006. _ _ 050 051 052 - - - Tr 18x8 (P4) 2 0.5 / 1000 17,700 18 15,608 15,905 13,074 13,5 9°02’ 1434 1.53
79.006. _ _ 056 057 058 053 054 055 Tr 20x4 1 0.4 / 2000 19,700 20 17,640 17,905 15,074 15,5 4°03’ 2534 1.94
79.006. _ _ 059 060 061 - - - Tr 20x8 (P4) 2 0.4 / 2000 19,700 20 17,640 17,905 15,074 15,5 8°03’ 2534 1.94
79.006. _ _ 068 069 070 065 066 067 Tr 22x5 1 0.4 / 2000 21,665 22 19,114 19,394 16,044 16,5 4°40’ 3232 2.29
79.006. _ _ 071 072 073 - - - Tr 22x10 (P5) 2 0.4 / 2000 21,665 22 19,080 19,394 16,044 16,5 9°16’ 3232 2.29
79.006. _ _ 077 078 079 074 075 076 Tr 24x5 1 0.4 / 2000 23,665 24 21,094 21,394 18,019 18,5 4°14’ 5175 2.78
79.006. _ _ 080 081 082 - - - Tr 24x10 (P5) 2 0.4 / 2000 23,665 24 21,058 21,394 18,019 18,5 8°25’ 5175 2.78
79.006. _ _ 095 096 097 - - - Tr 25x3 1 0.3 / 2000 24,665 25 22,094 22,394 21,103 21,5 2°20’ 6423 3.30
79.006. _ _ 086 087 088 083 084 085 Tr 25x5 1 0.3 / 2000 24,764 25 23,165 23,415 19,019 19,5 4°03’ 9735 3.05
79.006. _ _ 092 093 094 - - - Tr 25x25 (P5) 5 0.3 / 2000 24,665 25 22,094 22,394 19,019 19,5 19°30’ 6423 3.05
79.006. _ _ 101 102 103 098 099 100 Tr 26x5 1 0.3 / 2000 25,665 26 23,094 23,394 20,019 20,5 3°52’ 7884 3.33
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
29www.powerbelt.ro
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul de încl. al elicei
Lead angle
Moment de inerție Moment of inertia
(mm4)
Greu-tate
Weight (kg/m)
Tip de șurub
Screw type
Dreapta Right
Stânga Left d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m L=1m L=2m L=3m
79.006. _ _ 104 105 106 - - - Tr 26x10 (P5) 2 0.3 / 2000 25,665 26 23,094 23,394 20,019 20,5 7°42’ 7884 3.33
79.006. _ _ 110 111 112 107 108 109 Tr 28x5 1 0.3 / 2000 27,665 28 25,094 25,394 22,019 22,5 3°34’ 11539 3.92
79.006. _ _ 113 114 115 - - - Tr 28x10 (P5) 2 0.3 / 2000 27,665 28 25,094 25,394 22,019 22,5 7°07’ 11539 3.92
79.006. _ _ 135 136 137 132 133 134 Tr 30x6 1 0.3 / 2000 29,625 30 26,547 26,882 22,463 23,0 4°03’ 13650 4.38
79.006. _ _ 138 139 140 - - - Tr 30x12 (P6) 2 0.3 / 2000 29,625 30 26,547 26,882 22,463 23,0 8°03’ 13650 4.38
79.006. _ _ 147 148 149 144 145 146 Tr 32x6 1 0.3 / 3000 31,625 32 28,547 28,882 24,463 25,0 3°46’ 17580 5.06
79.006. _ _ 150 151 152 - - - Tr 32x12 (P6) 2 0.3 / 3000 31,625 32 28,547 28,882 24,463 25,0 7°30’ 17580 5.06
79.006. _ _ 174 175 176 171 172 173 Tr 35x6 1 0.3 / 3000 34,625 35 31,547 31,882 27,463 28,0 3°25’ 30000 6.16
79.006. _ _ 177 178 179 - - - Tr 35x8 1 0.3 / 3000 34,550 35 30,493 30,868 25,399 26,0 4°42’ 21980 5.85
79.006. _ _ 183 184 185 180 181 182 Tr 36x6 1 0.3 / 3000 35,625 36 32,547 32,882 28,463 29,0 3°19’ 34540 6.56
79.006. _ _ 186 187 188 - - - Tr 36x12 (P6) 2 0.3 / 3000 35,625 36 32,547 32,882 28,463 29,0 6°36’ 34540 6.56
79.006. _ _ 210 211 212 207 208 209 Tr 40x7 1 0.3 / 3000 39,575 40 36,020 36,375 31,431 32,0 3°30’ 51030 8.03
79.006. _ _ 222 223 224 - - - Tr 40x8 1 0.3 / 3000 39,550 40 35,493 35,868 30,399 31,0 4°03’ 44560 7.90
79.006. _ _ 219 220 221 - - - Tr 40x10 1 0.3 / 3000 39,470 40 34,450 34,850 28,350 29,0 5°12’ 31700 7.49
79.006. _ _ 213 214 215 - - - Tr 40x14 (P7) 2 0.3 / 3000 39,575 40 36,020 36,375 31,431 32,0 6°58’ 51300 8.03
79.006. _ _ 231 232 233 228 229 230 Tr 44x7 1 0.3 / 3000 43,575 44 40,020 40,375 35,431 36,0 3°09’ 81820 9.90
79.006. _ _ 237 238 239 234 235 236 Tr 45x8 1 0.3 / 3000 44,550 45 40,493 40,868 35,399 36,0 3°33’ 81245 10.23
79.006. _ _ 261 262 263 258 259 260 Tr 50x8 1 0.3 / 3000 49,550 50 45,468 45,868 40,368 41,0 3°10’ 136930 12.90
79.006. _ _ 264 265 266 - - - Tr 50x10 1 0.3 / 3000 49,470 50 44,425 44,850 38,319 39,0 4°03’ 150834 12.37
79.006. _ _ 267 268 269 - - - Tr 55x9 1 0.3 / 3000 54,500 55 49,935 50,360 44,329 45,0 3°15’ 189550 15.51
79.006. _ _ 273 274 275 270 271 272 Tr 60x9 1 0.3 / 3000 59,500 60 54,935 55,360 49,329 50,0 2°57’ 302600 18.74
79.006. _ _ 279 280 281 276 277 278 Tr 70x10 1 0.3 / 3000 69,470 70 64,425 64,850 58,319 59,0 2°48’ 587540 25.80
79.006. _ _ 285 286 287 282 283 284 Tr 80x10 1 0.3 / 3000 79,470 80 74,425 74,850 68,319 69,0 2°26’ 1069390 34.39
79.006. _ _ 288 289 290 - - - Tr 90x12 1 1 / 300 89,400 90 83,335 83,830 76,246 77,0 2°36’ 1658969 43.07
79.006. _ _ 291 292 293 - - - Tr 95x16 1 1 / 300 94,290 95 86,250 86,810 76,110 77,0 3°21’ 1647164 45.90
79.006. _ _ 294 295 296 - - - Tr 100x12 1 1 / 300 99,400 100 93,330 93,830 86,215 87,0 2°19’ 2712072 53.99
79.006. _ _ 297 298 299 - - - Tr 100x16 1 1 / 300 99,290 100 91,250 91,810 81,110 82,0 3°10’ 2124553 51.37
79.006. _ _ 300 301 302 - - - Tr 120x14 1 1 / 300 119,330 120 112,290 112,820 103,157 104,0 2°16’ 5558591 77.72
79.006. _ _ 303 304 305 - - - Tr 120x16 1 1 / 300 119,290 120 111,250 111,810 101,110 102,0 2°36’ 5130342 76.34
79.006. _ _ 306 307 308 - - - Tr 140x14 1 1 / 300 139,330 140 132,290 132,820 123,157 124,0 1°55’ 11292921 107.87
Producătorul articolelor / Producer of the items:30 www.powerbelt.ro
TIP KEQ (79.002) KEQ (79.002) TYPE
Penru acționare manuală For manual movement
Material Material
C15 oțel (1.1141) C15 steel (1.1141)
Toleranță Tolerance
200 µm / 300 mm
Duritatea suprafeței Surface hardness
160/180 HB
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul
de încl. al elicei Lead angle
Moment de inerție Moment of inertia
(mm4)
Greutate Weight (kg/m)Tip de șurub
Screw type
Dreapta Right d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m
79.002. _ _ _ 014 015 016 Tr 12x3 1 - 11.764 12 10.191 10.415 8.135 8,5 5°12’ 215 0,65
79.002. _ _ _ 023 024 025 Tr 14x4 1 - 13.700 14 11.640 11.905 9.074 9,5 6°03’ 333 0,93
79.002. _ _ _ 038 039 040 Tr 16x4 1 - 15.700 16 13.640 13.905 11.074 11,5 5°12’ 738 1,17
79.002. _ _ _ 047 048 049 Tr 18x4 1 - 17.700 18 15.640 15.905 13.074 13,5 4°33’ 1434 1,53
79.002. _ _ _ 056 057 058 Tr 20x4 1 - 19.700 20 17.640 17.905 15.074 15,5 4°03’ 2534 1,94
79.002. _ _ _ 068 069 070 Tr 22x5 1 - 21.665 22 19.114 19.394 16.044 16,5 4°40’ 3232 2,29
79.002. _ _ _ 077 078 079 Tr 24x5 1 - 23.665 24 21.094 21.394 18.019 18,5 4°14’ 5175 2,79
79.002. _ _ _ 101 102 103 Tr 26x5 1 - 25.665 26 23.094 23.394 20.019 20,5 3°52’ 7884 3,33
79.002. _ _ _ 110 111 112 Tr 28x5 1 - 27.665 28 25.094 25.394 22.019 22,5 3°34’ 11539 3,92
79.002. _ _ _ 134 135 136 Tr 30x6 1 - 29.625 30 26.547 26.882 22.463 23,0 4°03’ 13650 4,38
79.002. _ _ _ 146 147 148 Tr 32x6 1 - 31.625 32 28.547 28.882 24.463 25,0 3°46’ 17580 5,06
79.002. _ _ _ 182 183 184 Tr 36x6 1 - 35.625 36 32.547 32.882 28.463 29,0 3°19’ 34540 6,56
79.002. _ _ _ 209 210 211 Tr 40x7 1 - 39.575 40 36.020 36.375 31.431 32,0 3°30’ 51030 8,03
79.002. _ _ _ 260 261 262 Tr 50x8 1 - 49.550 50 45.468 45.868 40.368 41,0 3°10’ 136930 12,90
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
31www.powerbelt.ro
TIP KKA (79.003) KKA (79.003) TYPE
Pentru mișcări mecanice For motorical movement
Material Material
C45 oțel (1.0503) C45 steel (1.0503)
Toleranță Tolerance
50 µm / 300 mm
Duritatea suprafeței Surface hardness
250 HB
Cod Codes
Ø x Pas Ø x Lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm) Δƒ
Dimensiuni Dimensions
(mm)Unghiul
de încl. al elicei Lead angle
Moment de inerție
Moment of inertia (mm4)
Greu-tate
Weight (kg/m)Tip de șurub
Screw type
Dreapta Right d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m
79.003. _ _ _ 038 039 040 Tr 16x4 1 0,5 / 1000 15.700 16 13.640 13.905 11.074 11,5 5°12’ 738 1,17
79.003. _ _ _ 056 057 058 Tr 20x4 1 0,4 / 2000 19.700 20 17.640 17.905 15.074 15,5 4°03’ 2534 1,94
79.003. _ _ _ 086 087 088 Tr 25x5 1 0,3 / 2000 24.665 25 22.094 22.394 19.019 19,5 4°03’ 6423 3,05
79.003. _ _ _ 110 111 112 Tr 28x5 1 0,3 / 2000 27.665 28 25.094 25.394 22.019 22,5 3°34’ 11539 3,92
79.003. _ _ _ 135 136 137 Tr 30x6 1 0,3 / 3000 29.625 30 26.547 26.882 22.463 23,0 4°03’ 1365 4,38
79.003. _ _ _ 174 175 176 Tr 35x6 1 0,3 / 3000 29.665 30 27.094 27.394 24.019 24,5 3°25’ 30000 6,16
79.003. _ _ _ 210 211 212 Tr 40x7 1 0,3 / 3000 39.575 40 36.020 36.375 31.431 32,0 3°30’ 51030 8,03
79.003. _ _ _ 261 262 263 Tr 50x8 1 0,3 / 3000 49.550 50 45.468 45.868 40.368 41,0 3°10’ 136930 12,9
Producătorul articolelor / Producer of the items:32 www.powerbelt.ro
TIP KRP (79.005) KRP (79.005) TYPE
Pentru mișcări mecanice For motorical movement
Material Material
Inox A2 (1.4301) Inox A2 (1.4301)
Toleranță Tolerance
200 µm / 300 mm
Duritatea suprafeței Surface hardness
260 HB
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul de încl. al elicei
Lead angle
Moment de inerție
Moment of inertia (mm4)
Greu-tate
Weight (kg/m)
Tip de șurub
Screw type
Dreapta Right
Stânga Left d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m L=1m L=2m L=3m
79.005. _ _ 014 015 016 011 012 013 Tr 12x3 1 0.7 / 1000 11,764 12 10,191 10,415 8,135 8,5 5°12’ 215 0.65
79.005. _ _ 017 018 019 - - - Tr 12x6 1 0.7 / 1000 11,764 12 10,191 10,415 8,135 8,5 10°19’ 215 0.65
79.005. _ _ 023 024 025 020 021 022 Tr 14x4 1 0.7 / 1000 13,700 14 11,640 11,905 9,074 9,5 6°03’ 333 0.86
79.005. _ _ 038 039 040 035 036 037 Tr 16x4 1 0.7 / 1500 15,700 16 13,640 13,905 11,074 11,5 5°12’ 738 1.17
79.005. _ _ 041 042 043 - - - Tr 16x8 1 0.7 / 1500 15,700 16 13,640 13,905 11,074 11,5 10°19’ 738 1.17
79.005. _ _ 047 048 049 044 045 046 Tr 18x4 1 0.7 / 1500 17,700 18 15,640 15,905 13,074 13,5 4°33’ 1434 1.53
79.005. _ _ 056 057 058 053 054 055 Tr 20x4 1 0.6 / 2000 19,700 20 17,640 17,905 15,074 15,5 4°03’ 2534 1.94
79.005. _ _ 059 060 061 - - - Tr 20x8 1 0.6 / 2000 19,700 20 17,640 17,905 15,074 15,5 8°03’ 2534 1.94
79.005. _ _ 077 078 079 074 075 076 Tr 24x5 1 0.4 / 2000 23,665 24 21,094 21,394 18,019 18,5 4°14’ 5175 2.79
79.005. _ _ 086 087 088 083 084 085 Tr 25x5 1 0.4 / 2000 24,764 25 23,165 23,415 19,019 19,5 4°03’ 9735 3.05
79.005. _ _ 089 090 091 - - - Tr 25x10 1 0.4 / 2000 24,665 25 22,094 22,394 19,019 19,5 8°03’ 6423 3.05
79.005. _ _ 135 136 137 132 133 134 Tr 30x6 1 0.4 / 3000 29,625 30 26,547 26,882 22,463 23,0 4°03’ 13650 4.38
79.005. _ _ 138 139 140 - - - Tr 30x12 1 0.4 / 3000 29,625 30 26,547 26,882 22,463 23,0 8°03’ 13650 4.38
79.005. _ _ 174 175 176 171 172 173 Tr 35x5 1 0.3 / 3000 34,625 35 31,547 31,882 29,019 29,5 2°48’ 30000 6.16
79.005. _ _ 183 184 185 180 181 182 Tr 36x6 1 0.3 / 3000 35,625 36 32,547 32,882 28,463 29,0 3°19’ 34540 6.56
79.005. _ _ 210 211 212 207 208 209 Tr 40x7 1 0.3 / 3000 39,575 40 36,020 36,375 31,431 32,0 3°30’ 51030 8.03
79.005. _ _ 213 214 215 - - - Tr 40x14 1 0.3 / 3000 39,575 40 36,020 36,375 31,431 32,0 6°58’ 51300 8.03
79.005. _ _ 261 262 263 258 259 260 Tr 50x8 1 0.3 / 3000 49,550 50 45,468 45,868 40,368 41,0 3°10’ 136930 12.90
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
33www.powerbelt.ro
TIP KAM (79.008) KAM (79.008) TYPE
Penru acționare manuală For manual movement
Material Material
Inox A4 (1.4401) Inox A4 (1.4401)
Toleranță Tolerance
200 µm / 300 mm
Duritatea suprafeței Surface hardness
280 HB
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul de încl. al elicei
Lead angle
Moment de inerție Moment of inertia
(mm4)
Greu-tate
Weight (kg/m)Tip de șurub
Screw type
Dreapta Right
Stânga Left d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m L=1m L=2m L=3m
79.008. _ _ 009 010 - - - - Tr 10x2 1 0.7 / 1000 9,828 10 8,739 8,929 7,191 7,5 4°02’ 131 0,48
79.008. _ _ 014 015 016 011 012 013 Tr 12x3 1 0.7 / 1000 11,764 12 10,191 10,415 8,135 8,5 5°12’ 215 0.65
79.008. _ _ 038 039 040 035 036 037 Tr 16x4 1 0.7 / 1500 15,700 16 13,640 13,905 11,074 11,5 5°12’ 738 1.17
79.008. _ _ 047 048 049 - - - Tr 18x4 1 0.7 / 1500 17,700 18 15,640 15,905 13,074 13,5 4°33’ 1434 1.53
79.008. _ _ 056 057 058 053 054 055 Tr 20x4 1 0.6 / 2000 19,700 20 17,640 17,905 15,074 15,5 4°03’ 2534 1.94
79.008. _ _ 068 069 070 - - - Tr 22x5 1 0.6 / 2000 21,665 22 19,114 19,394 16,044 16,5 4°40’ 3232 2.29
79.008. _ _ 077 078 079 074 075 076 Tr 24x5 1 0.4 / 2000 23,665 24 21,094 21,394 18,019 18,5 4°14’ 5175 2.79
79.008. _ _ 101 102 103 - - - Tr 26x5 1 0.4 / 2000 25,665 26 23,094 23,394 20,019 20,5 3°52’ 7884 3,33
79.008. _ _ 110 111 112 - - - Tr 28x5 1 0.4 / 2000 27,665 28 25,094 25,394 22,019 22,5 3°34’ 11539 3,92
79.008. _ _ 135 136 137 132 133 134 Tr 30x6 1 0.4 / 3000 29,625 30 26,547 26,882 22,463 23,0 4°03’ 13650 4.38
79.008. _ _ 147 148 149 144 145 146 Tr 32x6 1 0.4 / 3000 31,625 32 28,547 28,882 24,463 25,0 3°46’ 17580 5,06
79.008. _ _ 183 184 185 180 181 182 Tr 36x6 1 0.3 / 3000 35,625 36 32,547 32,882 28,463 29,0 3°19’ 34540 6.56
79.008. _ _ 210 211 212 207 208 209 Tr 40x7 1 0.3 / 3000 39,575 40 36,020 36,375 31,431 32,0 3°30’ 51030 8.03
79.008. _ _ 261 262 263 258 259 260 Tr 50x8 1 0.3 / 3000 49,550 50 45,468 45,868 40,368 41,0 3°10’ 136930 12.90
79.008. _ _ 273 274 275 270 271 272 Tr 60x9 1 0.3 / 3000 59,500 60 54,935 55,360 49,329 50,0 2°57’ 302600 18,74
79.008. _ _ 279 280 281 276 277 278 Tr 70x10 1 0.3 / 3000 69,470 70 64,425 64,850 58,319 59,0 2°48’ 587540 25,80
Producătorul articolelor / Producer of the items:34 www.powerbelt.ro
TIP KRE (79.009) KRE (79.009) TYPE
Penru acționare manuală For manual movement
Material Material
Inox A2 (1.4301) Inox A2 (1.4301)
Toleranță Tolerance
200 µm / 300 mm
Duritatea suprafeței Surface hardness
260 HB
Cod Codes
Ø x pas Ø x lead
Începu-turi
Thread starts
Rectilin. Straight.
(mm/mm)
Dimensiuni Dimensions
(mm)Unghiul de încl. al elicei
Lead angle
Moment de inerție Moment of inertia
(mm4)
Greu-tate
Weight (kg/m)Tip de șurub
Screw type
Dreapta Right
Stânga Left d
mind
maxd2
mind2
maxd3
mind3
maxL=1m L=2m L=3m L=1m L=2m L=3m
79.009. _ _ 014 015 016 011 012 013 Tr 12x3 1 1.5 / 300 11,764 12 10,191 10,415 8,135 8,5 5°12’ 215 0.65
79.009. _ _ 023 024 025 020 021 022 Tr 14x4 1 1.5 / 300 13,700 14 11,640 11,905 9,074 9,5 6°03’ 333 0.86
79.009. _ _ 038 039 040 035 036 037 Tr 16x4 1 1.5 / 300 15,700 16 13,640 13,905 11,074 11,5 5°12’ 738 1.17
79.009. _ _ 047 048 049 044 045 046 Tr 18x4 1 1.5 / 300 17,700 18 15,640 15,905 13,074 13,5 4°33’ 1434 1.53
79.009. _ _ 056 057 058 053 054 055 Tr 20x4 1 1.5 / 300 19,700 20 17,640 17,905 15,074 15,5 4°03’ 2534 1.94
79.009. _ _ 077 078 079 074 075 076 Tr 24x5 1 1.5 / 300 23,665 24 21,094 21,394 18,019 18,5 4°14’ 5175 2.79
79.009. _ _ 086 087 088 083 084 085 Tr 25x5 1 1.5 / 300 24,764 25 23,165 23,415 19,019 19,5 4°03’ 9735 3.05
79.009. _ _ 101 102 103 098 099 100 Tr 26x5 1 0.2 / 300 25,665 26 23,094 23,394 20,019 20,5 3°52’ 7884 3,33
79.009. _ _ 110 111 112 107 108 109 Tr 28x5 1 0.2 / 300 27,665 28 25,094 25,394 22,019 22,5 3°34’ 11539 3,92
79.009. _ _ 135 136 137 132 133 134 Tr 30x6 1 1.5 / 300 29,625 30 26,547 26,882 22,463 23,0 4°03’ 13650 4.38
79.009. _ _ 174 175 176 171 172 173 Tr 35x5 1 1.5 / 300 34,625 35 31,547 31,882 29,019 29,5 2°48’ 30000 6.16
79.009. _ _ 183 184 185 180 181 182 Tr 36x6 1 1.5 / 300 35,625 36 32,547 32,882 28,463 29,0 3°19’ 34540 6.56
79.009. _ _ 210 211 212 207 208 209 Tr 40x7 1 1.5 / 300 39,575 40 36,020 36,375 31,431 32,0 3°30’ 51030 8.03
79.009. _ _ 261 262 263 258 259 260 Tr 50x8 1 1.5 / 300 49,550 50 45,468 45,868 40,368 41,0 3°10’ 136930 12.90
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
35www.powerbelt.ro
TIP BFA (79.001) BFA (79.001) TYPE
Penru acționare manuală For manual movement
Material Material
R50 oțel R50 steel
Toleranță Tolerance
----
Duritatea suprafeței Surface hardness
160/180 HB
Cod Codes
Ø x pas Ø x lead
Începuturi Thread starts
Dimensiuni Dimensions
(mm)
Unghiul de încl. al
elicei Lead angle
Moment de inerție Moment of inertia
(mm4)
Greutate Weight (kg/m)d
mind
maxd2
mind2
maxd3
mind3
max L T
79.001.000 Tr 12x3 1 11,764 12 10,191 10,415 8,135 8,5 3020 20 5°12’ 215 0.65
79.001.001 Tr 14x4 1 13,700 14 11,640 11,905 9,074 9,5 3020 20 6°03’ 333 0.86
79.001.002 Tr 16x4 1 15,700 16 13,640 13,905 11,074 11,5 3020 20 5°12’ 738 1.17
79.001.003 Tr 20x4 1 19,700 20 17,640 17,905 15,074 15,5 3020 20 4°03’ 2534 1.94
79.001.004 Tr 22x5 1 21,665 22 19,114 19,394 16,044 16,5 3020 20 4°40’ 3232 2.29
79.001.005 Tr 26x5 1 25,665 26 23,094 23,394 20,019 20,5 3020 20 3°52’ 7884 3.33
79.001.006 Tr 30x6 1 29,625 30 26,547 26,882 22,463 23,0 3020 20 4°03’ 13650 4.38
79.001.007 Tr 36x6 1 35,625 36 32,547 32,882 28,463 29,0 3020 20 3°19’ 34540 6.56
Producătorul articolelor / Producer of the items:36 www.powerbelt.ro
PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL NUTS
PIULIȚĂ HEXAGONALĂ DIN OȚEL HEXAGONAL STEEL NUT
Material Material
oțel steel
Sudabil Weldable
numai cu sudură MIG-MAG only MIG-MAG welding
Tip Type
MES (79.013)
Cod Code Ø x pas
Ø x leadÎnceputuri
Thread startsE
mmL
mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.013.009 79.013.007 Tr 10x2 1 17 15 0,023 150
79.013.003 79.013.001 Tr 10x3 1 17 15 0,021 240
79.013.014 79.013.011 Tr 12x3 1 19 18 0,027 296
79.013.032 79.013.029 Tr 14x3 1 22 21 0,044 395
79.013.023 79.013.020 Tr 14x4 1 22 21 0,044 395
79.013.038 79.013.035 Tr 16x4 1 27 24 0,082 528
79.013.047 79.013.044 Tr 18x4 1 27 27 0,084 553
79.013.056 79.013.053 Tr 20x4 1 30 30 0,114 847
79.013.068 79.013.065 Tr 22x5 1 30 33 0,112 1010
79.013.077 79.013.074 Tr 24x5 1 36 36 0,200 1215
79.013.101 79.013.098 Tr 26x5 1 36 39 0,193 1440
79.013.110 79.013.107 Tr 28x5 1 41 42 0,291 1680
79.013.135 79.013.132 Tr 30x6 1 46 45 0,420 1908
79.013.147 79.013.144 Tr 32x6 1 46 48 0,411 2186
79.013.183 79.013.180 Tr 36x6 1 55 54 0,706 2800
79.013.210 79.013.207 Tr 40x7 1 65 60 1,172 3440
79.013.231 79.013.228 Tr 44x7 1 65 66 1,159 4200
79.013.261 79.013.258 Tr 50x8 1 75 75 1,783 5418
79.013.273 79.013.270 Tr 60x9 1 90 90 3,087 7847
79.013.279 79.013.276 Tr 70x10 1 90 105 2,837 10200
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
37www.powerbelt.ro
PIULIȚĂ CILINDRICĂ DIN OȚEL CYLINDRICAL STEEL NUT
Material Material
oțel steel
Sudabil Weldable
numai cu sudură MIG-MAG only MIG-MAG welding
Tip Type
MZP (79.010) MLF (79.021)
Cod Code Ø x pas
Ø x leadÎnceputuri
Thread startsd
mmL
mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.010.009 79.010.007 Tr 10x2 1 22 15 0,035 150
79.010.003 79.010.001 Tr 10x3 1 22 15 0.037 240
79.010.014 79.010.011 Tr 12x3 1 26 18 0.061 296
79.010.017 --- Tr 12x6 (P3) 2 26 18 0.061 296
79.010.032 79.010.029 Tr 14x3 1 30 21 0,090 395
79.010.023 79.010.020 Tr 14x4 1 30 21 0.095 395
79.010.038 79.010.035 Tr 16x4 1 36 24 0.158 528
79.021.041 --- Tr 16x8 (P4) 2 36 36 0,238 792
79.010.047 79.010.044 Tr 18x4 1 40 27 0.218 553
79.010.056 79.010.053 Tr 20x4 1 45 30 0.308 847
79.021.059 --- Tr 20x8 (P4) 2 40 40 0,306 1130
79.010.068 79.010.065 Tr 22x5 1 45 33 0.324 1010
79.010.077 79.010.074 Tr 24x5 1 50 36 0.440 1215
79.021.086 79.021.083 Tr 25x5 1 45 45 0,400 1590
79.021.089 --- Tr 25x10 (P5) 2 45 45 0,400 1590
79.010.101 79.010.098 Tr 26x5 1 50 39 0.454 1440
79.010.110 79.010.107 Tr 28x5 1 60 42 0.747 1680
79.021.113 --- Tr 28x10 (P5) 2 45 45 0,360 1800
79.010.135 79.010.132 Tr 30x6 1 60 45 0.773 1908
79.021.138 --- Tr 30x12 (P6) 2 50 50 0,520 2120
79.010.147 79.010.144 Tr 32x6 1 60 48 0.790 2186
79.021.174 79.021.171 Tr 35x6 1 55 55 0,650 2764
79.010.183 79.010.180 Tr 36x6 1 75 54 1.476 2800
79.010.210 79.010.207 Tr 40x7 1 80 60 1.826 3440
79.021.213 --- Tr 40x14 (P7) 2 60 60 0,790 3440
79.010.231 79.010.228 Tr 44x7 1 80 66 1.878 4200
79.021.237 79.021.234 Tr 45x8 1 65 65 0,950 4186
79.010.261 79.010.258 Tr 50x8 1 90 75 2.680 5418
79.021.267 --- Tr 55x9 1 80 80 1,780 6345
79.010.273 79.010.270 Tr 60x9 1 100 90 3,698 7847
79.010.279 79.010.276 Tr 70x10 1 110 105 4,884 10200
79.010.285 79.010.282 Tr 80x10 1 120 120 6,210 14137
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:38 www.powerbelt.ro
PIULIȚĂ CILINDRICĂ DIN BRONZ CILINDRICAL BRONZE NUT
Material Material
bronz bronze
Sudabil Weldable
--- ---
Tip Type
HSN (79.012) HBD (79.022)
Cod Code Ø x pas
Ø x leadÎnceputuri
Thread startsd
mmL
mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.022.009 79.022.007 Tr 10x2 1 22 20 0,058 200
79.022.003 79.022.001 Tr 10x3 1 22 20 0,057 320
79.012.015 79.012.012 Tr 12x3 1 36 36 0.302 594
79.022.014 79.022.011 Tr 12x3 1 26 24 0,094 396
79.022.017 --- Tr 12x6 (P3) 2 26 24 0,094 396
79.022.032 79.022.029 TR 14x3 1 30 28 0,146 526
79.012.024 79.012.021 Tr 14x4 1 36 36 0.290 677
79.022.024 79.022.021 Tr 14x4 1 30 28 0,146 526
79.012.039 79.012.036 Tr 16x4 1 36 36 0.276 792
79.022.038 79.022.035 Tr 16x4 1 36 32 0,245 704
79.012.042 --- Tr 16x8 (P4) 2 36 36 0.276 792
79.012.048 79.012.045 Tr 18x4 1 36 36 0.259 905
79.012.057 79.012.054 Tr 20x4 1 40 40 0.354 1130
79.022.056 79.022.053 Tr 20x4 1 45 40 0,476 1130
79.012.060 --- Tr 20x8 (P4) 2 40 40 0.354 1130
79.012.069 79.012.066 Tr 22x5 1 40 40 0.33 1225
79.022.068 79.022.065 Tr 22x5 1 45 40 0,456 1225
79.022.077 79.022.074 Tr 24x5 1 50 48 0,680 1620
79.012.087 79.012.084 Tr 25x5 1 45 45 0.47 1590
79.012.090 --- Tr 25x10 (P5) 2 45 45 0.47 1590
79.022.101 79.022.098 Tr 26x5 1 50 48 0,648 1770
79.012.111 79.012.108 Tr 28x5 1 45 45 0.42 1800
79.022.111 79.022.108 Tr 28x5 1 60 60 1,237 2400
79.012.114 --- Tr 28x10 (P5) 2 45 45 0.42 1800
79.012.136 79.012.133 Tr 30x6 1 50 50 0.60 2120
79.012.139 --- Tr 30x12 (P6) 2 50 50 0.60 2120
79.022.147 79.022.144 Tr 32x6 1 60 60 1,145 2733
79.012.175 79.012.172 Tr 35x6 1 55 55 0.75 2764
79.022.183 79.022.180 Tr 36x6 1 75 72 2,189 2610
79.012.211 79.012.208 Tr 40x7 1 60 60 0.92 3440
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
39www.powerbelt.ro
Cod Code Ø x pas
Ø x leadÎnceputuri
Thread startsd
mmL
mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.022.211 79.022.208 Tr 40x7 1 80 80 2,823 4587
79.012.214 --- Tr 40x14 (P7) 2 60 60 0.92 3440
79.012.238 79.012.235 Tr 45x8 1 65 65 1.10 4186
79.012.262 79.012.259 Tr 50x8 1 70 70 1.30 5057
79.012.268 --- Tr 55x9 1 80 80 2.07 6345
79.012.274 79.012.271 Tr 60x9 1 80 80 1.75 6975
79.022.279 79.022.276 Tr 70x10 1 110 140 7,548 10200
79.022.285 79.022.282 Tr 80x10 1 120 160 9,600 18850
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:40 www.powerbelt.ro
PIULIȚĂ DE BRONZ CU FLANȘĂ FLANGED BRONZE NUT
Material Material
bronz bronze
Sudabil Weldable
------
Tip Type
FTN (79.015)FXN (79.023)FFR (79.024)
Cod code Ø x pas
Ø x lead
Începu-turi
Thread starts
d1 mm
d2 mm
d3 mm
d4 mm
d5 mm
p mm
L mm
s mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.024.009 79.024.007 Tr 10x2 1 25 34 42 5,0 -- -- 25 10 0,016 250
79.015.004 79.015.002 Tr 10x3 1 18 26 37 4.5 7.5 4.2 22 8 0.088 294
79.015.015 79.015.012 Tr 12x3 1 18 26 37 4.5 7.5 4.2 22 8 0.082 362
79.024.014 79.024.011 Tr 12x3 1 28 38 48 6,0 -- -- 35 12 0,276 400
79.023.019 --- Tr 12x6 (P3) 2 18 26 37 4,5 7,5 4,2 22 8 0,082 362
79.024.032 79.024.029 Tr 14x3 1 28 38 48 6,0 -- -- 35 12 0,272 460
79.015.024 79.015.021 Tr 14x4 1 20 30 42 5.5 9 5.2 25 10 0.123 470
79.015.039 79.015.036 Tr 16x4 1 22 32 45 5.5 9 5.2 30 10 0.149 660
79.024.038 79.024.035 Tr 16x4 1 28 38 48 6,0 -- -- 35 12 0,260 530
79.023.043 --- Tr 16x8 (P4) 2 22 32 45 5,5 9,5 5,2 30 10 0,149 660
79.015.048 79.015.045 Tr 18x4 1 25 35 48 5.5 9 5.2 35 10 0.188 880
79.015.057 79.015.054 Tr 20x4 1 30 40 52 5.5 9 5.2 40 10 0.267 1130
79.024.056 79.024.053 Tr 20x4 1 32 45 55 6,5 -- -- 44 12 0,370 870
79.023.061 --- Tr 20x8 (P4) 2 30 40 52 5,5 9,5 5,2 40 10 0,267 1130
79.023.064 --- Tr 20x20 (P5) 4 30 40 52 5,5 9,5 5,2 40 10 0,270 1100
79.015.069 79.015.066 Tr 22x5 1 30 40 52 5.5 9 5.2 40 10 0.247 1225
79.024.068 79.024.065 Tr 22x5 1 32 45 55 6,5 -- -- 44 12 0,360 1030
79.023.079 79.023.076 Tr 24x5 1 35 48 62 6,5 11,0 6,5 45 12 0,408 1520
79.024.077 79.024.074 Tr 24x5 1 32 45 55 6,5 -- -- 44 12 0,337 1040
79.015.087 79.015.084 Tr 25x5 1 35 48 62 6.5 11 6.5 45 12 0.393 1590
79.023.091 --- Tr 25x10 (P5) 2 35 48 62 6,5 11 6,5 45 12 0,393 1590
79.023.094 --- Tr 25x25 (P5) 5 35 48 62 6,5 11 6,5 45 12 0,393 1590
79.015.111 79.015.108 Tr 28x5 1 40 53 68 6.5 11 6.5 50 12 0.532 2000
79.023.115 --- Tr 28x10 (P5) 2 40 53 68 6.5 11 6.5 50 12 0.532 2000
79.015.117 79.015.118 Tr 30x3 1 40 53 68 6.5 11 6.5 50 12 0.482 2238
79.015.120 79.015.124 Tr 30x4 1 40 53 68 6.5 11 6.5 50 12 0.487 2200
79.015.127 79.015.130 Tr 30x5 1 40 53 68 6.5 11 6.5 50 12 0.492 2160
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
41www.powerbelt.ro
Cod code Ø x pas
Ø x lead
Începu-turi
Thread starts
d1 mm
d2 mm
d3 mm
d4 mm
d5 mm
p mm
L mm
s mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.015.136 79.015.133 Tr 30x6 1 40 53 68 6.5 11 6.5 50 12 0.497 2120
79.024.135 79.024.132 Tr 30x6 1 38 50 62 6,5 -- -- 46 14 0,472 1370
79.023.140 --- Tr 30x12 (P6) 2 40 53 68 6.5 11 6.5 50 12 0.497 2120
79.023.143 --- Tr 30x30 (P5) 6 40 53 68 6.5 11 6.5 50 12 0,492 2590
79.023.149 79.023.146 Tr 32x6 1 40 53 68 6.5 11 6.5 50 12 0,455 2277
79.024.147 79.024.144 Tr 32x6 1 45 58 70 6,5 -- -- 54 16 0,078 1710
79.015.154 79.015.157 Tr 35x3 1 50 63 78 8.5 14 8.5 60 15 0.862 3160
79.015.160 79.015.163 Tr 35x4 1 50 63 78 8.5 14 8.5 60 15 0.869 3110
79.015.166 79.015.169 Tr 35x5 1 50 63 78 8.5 14 8.5 60 15 0.876 3060
79.015.175 79.015.172 Tr 35x6 1 50 63 78 8.5 14 8.5 60 15 0.883 3015
79.015.178 --- Tr 35x8 1 50 63 78 8.5 14 8.5 60 15 0.898 2920
79.024.183 79.024.180 Tr 36x6 1 45 58 70 6,5 -- -- 54 16 0,694 1950
79.023.185 79.023.182 Tr 36x6 1 50 63 78 8,5 14,0 8,5 60 15 0,854 3110
79.015.190 79.015.193 Tr 40x3 1 55 68 84 8.5 14 8.5 65 15 1.030 3930
79.015.196 79.015.199 Tr 40x4 1 55 68 84 8.5 14 8.5 65 15 1.039 3880
79.015.202 79.015.205 Tr 40x5 1 55 68 84 8.5 14 8.5 65 15 1.048 3828
79.015.226 --- Tr 40x6 1 55 68 84 8.5 14 8.5 65 15 1.057 3778
79.015.211 79.015.208 Tr 40x7 1 55 68 84 8.5 14 8.5 65 15 1.066 3727
79.024.210 79.024.207 Tr 40x7 1 63 78 95 8,5 -- -- 66 16 1,788 2650
79.015.223 --- Tr 40x8 1 55 68 84 8.5 14 8.5 65 15 1.075 3675
79.023.215 --- Tr 40x14 (P7) 2 55 68 84 8,5 14,0 8,5 65 15 1,066 3727
79.023.218 --- Tr 40x40 (P8) 5 55 65 84 8,5 14,0 8,5 65 15 1,075 3675
79.023.233 79.023.230 Tr 44x7 1 55 72 90 8,5 14,0 8,5 65 15 1,029 4135
79.024.231 79.024.228 Tr 44x7 1 63 78 95 8,5 -- -- 66 16 1,657 2940
79.015.238 79.015.235 Tr 45x8 1 55 72 90 8.5 14 8.5 65 15 0.999 4186
79.015.241 79.015.244 Tr 50x3 1 65 80 100 10.5 17 10.5 80 20 1.679 6095
79.015.247 79.015.250 Tr 50x4 1 65 80 100 10.5 17 10.5 80 20 1.693 6030
79.015.253 79.015.256 Tr 50x5 1 65 80 100 10.5 17 10.5 80 20 1.707 5970
79.015.262 79.015.259 Tr 50x8 1 65 80 100 10.5 17 10.5 80 20 1.749 5780
79.024.261 79.024.258 Tr 50x8 1 72 90 110 10,5 -- -- 75 18 2,500 4540
79.015.268 --- Tr 55x9 1 65 80 100 10.5 17 10.5 80 20 1.475 6345
79.015.311 79.015.317 Tr 60x6 1 75 95 120 12.5 19 12.5 100 25 2.865 8950
79.015.312 79.015.318 Tr 60x7 1 75 95 120 12.5 19 12.5 100 25 2.886 8875
79.015.274 79.015.271 Tr 60x9 1 75 95 120 12.5 19 12.5 100 25 2.927 8718
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:42 www.powerbelt.ro
PIULIȚĂ LUNGĂ DE BRONZ CU FLANȘĂ FLANGED ELONGATED BRONZE NUT
Material Material
bronz bronze
Sudabil Weldable
------
Tip Type
HDL (79.011)
Cod Code Ø x pas
Ø x lead
Începu-turi
Thread starts
d1 mm
d2 mm
d3 mm
d4 mm
d5 mm
p mm
L mm
s mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.011.023 79.011.020 Tr 14x4 1 20 30 42 5.5 9,5 5,2 42 10 0,151 790
79.011.038 79.011.035 Tr 16x4 1 22 32 45 5.5 9,5 5,2 48 10 0,183 1056
79.011.041 --- Tr 16x8 (P4) 2 22 32 45 5,5 9,5 5,2 48 10 0,183 1056
79.011.047 79.011.044 Tr 18x4 1 25 35 48 5.5 9,5 5,2 54 10 0,233 1356
79.011.056 79.011.053 Tr 20x4 1 30 40 52 5.5 9,5 5,2 60 12 0,368 1696
79.011.059 --- Tr 20x8 (P4) 2 30 40 52 5,5 9,5 5,2 60 12 0,368 1696
79.011.068 79.011.065 Tr 22x5 1 30 40 52 5.5 9,5 5,2 60 12 0,338 1838
79.011.086 79.011.083 Tr 25x5 1 35 48 62 6.5 11 6,5 75 15 0,586 2650
79.011.089 --- Tr 25x10 (P5) 2 35 48 62 6,5 11 6,5 75 15 0,586 2650
79.011.092 --- Tr 25x25 (P5) 5 35 48 62 6,5 1 6,5 75 15 0,586 2650
79.011.110 79.011.107 Tr 28x5 1 40 53 68 6.5 11 6,5 90 18 0,903 3600
79.011.113 --- Tr 28x10 (P5) 2 40 53 68 6.5 11 6,5 90 18 0,903 3600
79.011.116 --- Tr 30x3 1 40 53 68 6.5 11 6,5 90 18 0,841 3816
79.011.135 79.011.132 Tr 30x6 1 40 53 68 6.5 11 6,5 90 18 0,841 3816
79.011.138 --- Tr 30x12 (P6) 2 40 53 68 6.5 11 6,5 90 18 0,784 3816
79.011.147 79.011.144 Tr 32x6 1 40 53 68 6.5 11 6,5 90 18 0,765 4100
79.011.174 79.011.171 Tr 35x6 1 50 63 78 8.5 14 8,5 105 20 1,439 5277
79.011.210 79.011.207 Tr 40x7 1 55 84 84 8,5 14 8,5 120 25 1,937 6880
79.011.219 --- Tr 40x10 1 55 84 84 8.5 14 8,5 120 25 1,986 6597
79.011.213 --- Tr 40x14 (P7) 2 55 84 84 8,5 14 8,5 120 25 1,937 6597
79.011.261 79.011.258 Tr 50x8 1 65 80 100 10.5 17 10,5 150 30 3,075 10840
79.011.264 --- Tr 50x10 1 65 80 100 10,5 17 10,5 150 30 3,127 10600
79.011.273 79.011.270 Tr 60x9 1 75 95 120 12.5 17 12.5 150 30 4,797 15700
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
43www.powerbelt.ro
PIULIȚĂ CILINDRICĂ DIN OȚEL INOXIDABIL CYLINDRICAL STAINLESS STEEL NUT
Material Material
oțel inoxidabil stainless steel
Sudabil Weldable
------
Tip Type
HDA (79.014)
Cod Code Ø x pas
Ø x leadÎnceputuri
Thread startsd
mmL
mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.014.014 79.014.011 Tr 12x3 1 26 18 0.060 297
79.014.023 79.014.020 Tr 14x4 1 30 21 0,095 395
79.014.038 79.014.035 Tr 16x4 1 36 24 0.157 528
79.014.056 79.014.053 Tr 20x4 1 45 30 0.305 847
79.014.077 79.014.074 Tr 24x5 1 50 36 0.436 1215
79.014.135 79.014.132 Tr 30x6 1 60 45 0.766 1908
79.014.183 79.014.180 Tr 36x6 1 75 54 1.462 2799
79.014.210 79.014.207 Tr 40x7 1 80 60 1.808 3440
79.014.261 79.014.258 Tr 50x8 1 90 75 2.653 5418
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:44 www.powerbelt.ro
PIULIȚĂ CILINDRICĂ DIN MATERIAL PLASTIC CYLINDRICAL PLASTIC NUT
Material Material
plastic plastic
Sudabil Weldable
------
Tip Type
MPH (79.016)
Cod Code Ø x Pas
Ø x LeadÎnceputuri
Thread startsd
mmL
mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.016.014 79.016.011 Tr 12x3 1 26 24 0.012 396
79.016.038 79.016.035 Tr 16x4 1 36 32 0.030 704
79.016.056 79.016.053 Tr 20x4 1 45 40 0.060 1130
79.016.086 79.016.083 Tr 25x5 1 50 48 0.083 1696
79.016.110 79.016.107 Tr 28x5 1 60 60 0.154 2400
79.016.113 --- Tr 28x10 (P5) 2 60 60 0.154 2400
79.016.135 79.016.132 Tr 30x6 1 60 60 0.150 2544
79.016.174 79.016.171 Tr 35x6 1 75 72 0.290 3618
79.016.210 79.016.207 Tr 40x7 1 80 80 0.355 4587
79.016.261 79.016.258 Tr 50x8 1 90 10 0.523 7225
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
45www.powerbelt.ro
PIULIȚĂ DIN MATERIAL PLASTIC CU FLANȘĂ FLANGED PLASTIC NUT
Material Material
plastic plastic
Sudabil Weldable
------
Tip Type
FCS (79.017)
Cod Code Ø x Pas
Ø x Lead
Începuturi Thread starts
d1 mm
d2 mm
d3 mm
d4 mm
d5 mm
p mm
L mm
s mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.017.014 79.017.011 Tr 12x3 1 18 26 37 4.5 7.5 4.2 36 12 0.016 594
79.017.038 79.017.035 Tr 16x4 1 22 32 45 5.5 9 5.2 48 16 0.030 1056
79.017.056 79.017.053 Tr 20x4 1 30 40 52 5.5 9 5.2 60 20 0.057 1696
79.017.059 --- Tr 20x8 (P4) 2 30 40 52 5.5 9 5.2 60 20 0.057 1696
79.017.086 79.017.083 Tr 25x5 1 35 48 62 6.5 11 6.5 75 25 0.094 2650
79.017.110 79.017.107 Tr 28x5 1 40 53 68 6.5 11 6.5 90 30 0.142 3600
79.017.113 --- Tr 28x10 (P5) 2 40 53 68 6.5 11 6.5 90 30 0.142 3600
79.017.135 79.017.132 Tr 30x6 1 40 53 68 6.5 11 6.5 90 30 0.135 3816
79.017.174 79.017.171 Tr 35x6 1 50 63 78 8.5 14 8.5 105 35 0.221 5277
79.017.210 79.017.207 Tr 40x7 1 55 68 84 8.5 14 8.5 120 40 0.289 6880
79.017.219 --- Tr 40x10 1 55 68 84 8.5 14 8.5 120 40 0.252 6597
79.017.261 79.017.258 Tr 50x8 1 65 80 10 10.5 17 10.5 150 50 0.476 1084
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:46 www.powerbelt.ro
PIULIȚĂ PĂTRATĂ DIN OȚEL SQUARE STEEL NUT
Material Material
oțel steel
Sudabil Weldable
numai cu sudură MIG-MAG only MIG-MAG welding
Tip Type
CQA (79.018)
Cod Code Ø x pas
Ø x leadÎnceputuri
Thread startsS
mmL
mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.018.009 79.018.007 Tr 10x2 1 17 15 0,027 150
79.018.014 79.018.011 Tr 12x3 1 25 30 0,123 616
79.018.032 79.018.029 Tr 14x3 1 25 20 0,230 658
79.018.023 79.018.020 Tr 14x4 1 30 35 0.211 658
79.018.038 79.018.035 Tr 16x4 1 30 35 0.199 770
79.018.047 79.018.044 Tr 18x4 1 35 45 0.353 1131
79.018.056 79.018.053 Tr 20x4 1 40 50 0.517 1412
79.018.086 79.018.083 Tr 25x5 1 45 55 0.683 1943
79.018.135 79.018.132 Tr 30x6 1 50 60 0.877 2544
79.018.174 79.018.171 Tr 35x6 1 60 70 1.494 3517
79.018.183 79.018.180 Tr 36x6 1 60 70 1.465 3630
79.018.210 79.018.207 Tr 40x7 1 60 70 1.347 4013
79.018.261 79.018.258 Tr 50x8 1 70 90 2.183 6502
79.018.273 79.018.270 Tr 60x9 1 80 100 2,990 8718
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:
ȘURUBURI ȘI PIULIȚE CU FILET TRAPEZOIDAL TRAPEZOIDAL SCREW AND NUT
47www.powerbelt.ro
PIULIȚĂ PĂTRATĂ DIN ALAMĂ SQUARE BRASS NUT
Material Material
alamă brass
Sudabil Weldable
------
Tip Type
QOB (79.019)
Cod Code Ø x pas
Ø x leadÎnceputuri
Thread startsS
mmL
mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.019.003 79.019.001 Tr 10x3 1 25 20 0,094 320
79.019.014 79.019.011 Tr 12x3 1 25 25 0,110 411
79.019.032 79.019.029 Tr 14x3 1 25 20 0,076 658
79.019.023 79.019.020 Tr 14x4 1 30 35 0,224 658
79.019.038 79.019.035 Tr 16x4 1 30 35 0,212 770
79.019.047 79.019.044 Tr 18x4 1 35 45 0,379 1131
79.019.056 79.019.053 Tr 20x4 1 40 50 0,554 1412
79.019.086 79.019.083 Tr 25x5 1 45 55 0,735 1943
79.019.135 79.019.132 Tr 30x6 1 50 60 0,952 2544
79.019.174 79.019.171 Tr 35x6 1 60 70 1,617 3517
79.019.183 79.019.180 Tr 36x6 1 60 70 1,563 3630
79.019.210 79.019.207 Tr 40x7 1 60 70 1,465 4013
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Producătorul articolelor / Producer of the items:48 www.powerbelt.ro
PIULIȚĂ CILINDRICĂ MARE DIN BRONZ BIG CYLINDRICAL BRONZE NUT
Material Material
bronz bronze
Sudabil Weldable
------
Tip Type
BIG (79.020)
Cod Code Ø x pas
Ø x leadÎnceputuri
Thread startsd
mmL
mm
Greutate Weight
(kg)
At* mm2
dreapta right
stânga left
79.020.056 79.020.053 Tr 20x4 1 78 60 2,43 1696
79.020.086 79.020.083 Tr 25x5 1 78 75 2,96 2650
79.020.116 79.020.321 Tr 30x3 1 78 90 3.31 3600
79.020.119 79.020.122 Tr 30x4 1 78 90 3.32 3560
79.020.126 79.020.129 Tr 30x5 1 78 90 3.33 3500
79.020.135 79.020.132 Tr 30x6 1 78 90 3.33 3435
79.020.153 79.020.156 Tr 35x3 1 88 105 4.85 5000
79.020.159 79.020.162 Tr 35x4 1 88 105 4.86 4900
79.020.165 79.020.168 Tr 35x5 1 88 105 4.87 4820
79.020.174 79.020.171 Tr 35x6 1 88 105 4.89 4750
79.020.189 79.020.192 Tr 40x3 1 98 120 6.80 6530
79.020.195 79.020.198 Tr 40x4 1 98 120 6.82 6447
79.020.201 79.020.204 Tr 40x5 1 98 120 6.83 6360
79.020.225 79.020.206 Tr 40x6 1 98 120 6.85 6277
79.020.210 79.020.207 Tr 40x7 1 98 120 6.87 6200
79.020.219 --- Tr 40x10 1 98 120 6.91 6597
79.020.240 79.020.243 Tr 50x3 1 108 150 9.74 10300
79.020.246 79.020.249 Tr 50x4 1 108 150 9.77 10180
79.020.252 79.020.255 Tr 50x5 1 108 150 9.79 10070
79.020.261 79.020.258 Tr 50x8 1 108 150 9.87 9750
79.020.264 --- Tr 50x10 1 108 150 9.92 10600
79.020.309 --- Tr 60x6 1 118 180 13.29 14500
79.020.310 --- Tr 60x7 1 118 180 13.32 14380
79.020.273 --- Tr 60x9 1 118 180 13.36 14130
* Suprafață de contact între șurub și piuliță Contact surface between the screw and nut
Top Related