7/27/2019 Tolerance Accumulation
1/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
1
TOLERANCE ACCUMULATION
AND
ANALYSIS
7/27/2019 Tolerance Accumulation
2/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
2
ADDITION OF TOLERANCES
A and B two linear dimensions to be added
a1, a2 tolerance on Ab1, b2 tolerance on B
A+B = C
The tolerance on C to be analysed.
7/27/2019 Tolerance Accumulation
3/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
3
C is max. when A and B are max.
C is min. when A and B are min.
Cmax = A max + B max
Cmin
= Amin
+ Bmin
.
Cmax
= ( C + c2
)= (A + a2) + (B + b
2) ------- ( 1 )
Cmin
= ( C - c1
)= (Aa1) + ( Bb
1) ------- ( 2 )
c1, c2 tolerance on C
Subtracting Cmin
( 2 ) from Cmax
( 1 )
c2
+ c1
= (a1+a
2) + (b
1+ b
2)
If ( a1
+ a2
) = Ta
( b1
+ b2
) = Tb
( c1
+ c2
) = Tc
The Tolerance on the total length will be Tc = Ta + Tb
7/27/2019 Tolerance Accumulation
4/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
4
SUBTRACTION OF TOLERANCES
A and B two linear dimensions to be subtracted
a1, a2 tolerance on Ab1, b2 tolerance on B
A-B = C
The tolerance on C to be analysed.
7/27/2019 Tolerance Accumulation
5/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
5
C is max. when A is max. and B is min.
C is min. when A is min. and B is max.
C max = A maxB minC
min= A
minB
max;
A max = A + a2B
min= Bb
1
Amin
= Aa1
Bmax
= B + b2
Cmax
= ( C + c2
) = ( A + a2)( Bb
1) ----------- ( 3 )
C min = ( Cc1 ) = ( Aa1) ( B + b2 ) ---------- ( 4 )
Subtracting Cmin
( 4 ) from Cmax
( 3 )
(c 2 + c 1 ) = ( a2 + a1 ) + ( b2 + b1)If ( a2+ a
1) = T
a
( b2+ b
1) = T
b
( c2 + c1 ) = Tc
The Tolerance on the remaining length Tc = Ta + Tb
7/27/2019 Tolerance Accumulation
6/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
6
The tolerances are getting addedboth in addition and subtraction.
7/27/2019 Tolerance Accumulation
7/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
7
TO CALCULATE UNKNOWN DIMENSIONS
EXAMPLES
7/27/2019 Tolerance Accumulation
8/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
8
Case-1
x2 a2 z2x1 a1 z1
X A = Z
x2 a2 x2 - a1 z2x1 a1 x1 - a2 z1
X A = ( X A ) = Z
Therefore x2a1 = z2x2 = a1 + z2
x1a2 = z1
x1 = a2 +z1
Therefore
x2 a1 + z2
x1 a2 +z1X = ( A + Z )
The value of X and tolerances x1, x2 are un-known.
7/27/2019 Tolerance Accumulation
9/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
9
Example:
x2
+ 0.1 + 0.2
x1
- 0.1 - 0.2
X 5 = 10
x2
(0.1 ) = + 0.2
x2 + 0.1 = + 0.2
x2
= + 0.20.1 = + 0.1
x1 ( + 0 . 1 ) =0.2x1 0.1 =0.2
x1
= 0.1
x2 + 0.1 + 0.2
x1 - 0.1 - 0.2
X 5 = 10
+0.1 + 0.1 + 0.2
-0.1 - 0.1 - 0.2
15 5 = 10
The value of X and tolerances x1, x2 are un-known.
7/27/2019 Tolerance Accumulation
10/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
10
Case-2 a2 x2 z2a1 x1 z1
A X = Z
a2x1 z2a
1x
2z
1
( A - X ) = Z
The tolerances of the equation can be equated.a2 - x1 = z2x1 = a2 - z2
a1 - x2 = z1x2 = a1 - z1
Therefore
x2 a1 - z1x
1a
2 -z
2
X = ( A - Z )
The value of X and tolerances x1, x2 are un-known.
7/27/2019 Tolerance Accumulation
11/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
11
Example:
+ 0.1 x2 + 0.2
- 0.1 x1 - 0.2
15 - X = 10
+0.1x1 +0.2
-0.1 x2
-0.2
( 15 - X ) = Z
The tolerances of the equation can be equated.
+0.1 - x1
= +0.2
x1 = +0.1 - 0.2 = -0.1
-0.1 - x2
= -0.2
x2
= -0.1 +0.2 = +0.1
Therefore
+ 0.1 x2 + 0.2
- 0.1 x1 - 0.215 - X = 10
+ 0.1 +0.1 + 0.2
- 0.1 -0.1 - 0.2
15 - 5 = 10
7/27/2019 Tolerance Accumulation
12/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
12
+ 0.05- 0.03
Dimension A = 100 . 0
- 0.13
- 0.20
Dimension B = 60.0
Calculate the nominal size and the variation for the dimension C.
7/27/2019 Tolerance Accumulation
13/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
13
Nominal size C = Nominal size A Nominal size B
C = 10060 = 40
c2 a2 b2c1 a1 b1
C = A B
c2 + 0.05 0.13
c1 0.03 0.20
40 = 100 60
c2 = + 0.05(0.20 ) = + 0.25
c1 =0.03(0.13 ) = + 0.1
c2 +0.25
c1 + 0.1
C = 40
Verification: Tc = Ta +TbTa + Tb = + 0.05(0.03 ) + (0.13 )(0.2 )
= 0.15
Tc = 0.15
0.15 = 0.15
7/27/2019 Tolerance Accumulation
14/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
14
Calculate the dimension x and tolerance on x with M-M
and L-L as references
7/27/2019 Tolerance Accumulation
15/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
15
Considering MM as reference
a2 x2 b2a
1x
1b
1
A - X = B
+ 0.0 x2- 0.1 x1 0.1
30 - 8 = 22
+0.0 - x1-0.1 - x2 0.1
( 308 ) = 22
0.0x1 = + 0.1
x1
= 0.1
0.1 - x2 = 0.1
x2 = 0.0
x2 + 0. 0x
1 - 0.1
The value of X = 8
7/27/2019 Tolerance Accumulation
16/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
16
Considering LL as reference
a2 b2 x2a1 b1 x1
A B = X
+ 0.0 x2- 0.1 0.1 x
1
30 22 = 8
x2 = + 0.0
(
0.1) = + 0.1x1
= 0.1( +0.1) =0.2
x2 + 0.1
x1 - 0.2
X = 8
7/27/2019 Tolerance Accumulation
17/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
17
When divided by a constant number, thetolerance of the result, similarly decreasesproportionately
MULTIPLICATION & DIVISION BY A CONSTANTNUMBER
Any dimension with tolerances, if multipliedby a positive constant number, the tolerance of the result also increases
proportionately.
7/27/2019 Tolerance Accumulation
18/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
18
a2
a1When A is multiplied by a constant K , it becomes
a2 a2 * Ka1 a1 * K
( A ) * K = ( A * K )
MULTIPLICATION BY A CONSTANT NUMBER
Example :
+ 0.1 (+0.1) 3
+ 0.3 (+0.3) 3
4 * (3) = (4 * 3)
+0.3
+0.9
= 12
7/27/2019 Tolerance Accumulation
19/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
19
DIVISION BY A CONSTANT NUMBER
a2
a1When A is divided by a constant K , it becomes
a2 a2 K
a1
a1
K
( A ) K = (A K)
Example :
+0.3 0.3/3
+0.9 0.9/3
( 12 ) 3 = ( 12 / 3 )
+0.1
+0.3
= 4
7/27/2019 Tolerance Accumulation
20/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
20
Find out the variation of dimension x with reference to LL
EXAMPLE 1
7/27/2019 Tolerance Accumulation
21/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
21
x2 +0.0 +0.1 +0.0 +0.0 x2
x1 -0.2 -0.0 -0.2 -0.1 x1X = 50 5 38 5 = 2
x 2 = + 0.0(0.0 )( 0.2 )( 0.1 ) = + 0.3
x 1 = 0.2( + 0 . 1 )0.0 - 0.0 = 0.3
x2 +0.3
x1 -0.3 0.3
X = 2 = 2
Verification: Ta + Tb + Tc + Td = T xTa + Tb + Tc + Td = 0.2 + 0.1 + 0.2 + 0.1
= 0.6
T x = 0.3+0.3 = 0.6
0.6 = 0.6
7/27/2019 Tolerance Accumulation
22/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
22
Example 2 :
-0.040 +0.013 +0.012 +0.000 -0.006 x2
+0.040 -0.073 -0.009 +0.001 -0.019 -0.017 x1
150 - 20 + 95 - 15 + 65 + 15 = 290
x2=(0.040)-(- 0.073)+(0.013)-(0.001)+(0.000)+(-0.006) = + 0.119
x1=(0.000)-(-0.040)+(-0.009)-(0.012)+(-0.019)+(-0.017) =0.017
x2 + 0.119
x1 - 0.017
X = 290
Verification:
Ta+ Tb+ Tc + Td + Te + Tf = Tx
Ta+ Tb+ Tc + Td + Te + Tf = 0.040+ [(0.040)(0.073)] + [0.013(0.009)] +
[(+0.0120(+0.001)] + (0.019)+ [(0.006)(0.017)] = 0.136
T x = [0.119(0.017)] = 0.136
0.136 = 0.136
7/27/2019 Tolerance Accumulation
23/80THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
23
Example 3 : + 0.030 +0.021 +0.030 x2+0.046 + 0.011 +0.008 +0.011 x1
240 +75 20 60 = X
X = (240 + 752060) = 235x2 = + 0.046 + 0.030( + 0.008 )( + 0.011 ) = + 0.057
x1 = + 0.000 + 0.011( + 0.021 ) ( + 0.030 ) =0.040
x2 +0.057
x1 -0.040
235 = 235
Verification:
Ta + Tb + T c + Td = Tx.
Ta
+ Tb
+ Tc
+ Td
= 0.046 + ( 0.0300.011 ) + ( 0.0210.008 ) + ( 0.0300.011 )
= 0.097
Tx = 0.097
0.097 = 0.097
7/27/2019 Tolerance Accumulation
24/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
24
Example 4 : +0.012 +0.009 +0.013 +0.008 x2-0.007 -0.004 +0.063 -0.009 -0.003 x1
65 -20 +450 -120 +12 = 387
x2 = + 0.012(0.004 ) + 0.063(0.009) + 0.008 = + 0.096
x1 =0.007( + 0.009 ) + ( + 0.000 )( + 0.013) + (0.003)
= 0.032
x2 +0.0 96
x1 -0.032
387 = 387
Verification: Ta+Tb+Tc+Td+Te = TxTa+Tb+Tc+Td+Te =0.012(0.007)+ 0.009(0.004)+0.063+0.013
(0.009)+0.008(0.003)
= 0.128
Tx = 0.096(0.032) = 0.128
0.128 = 0.128
7/27/2019 Tolerance Accumulation
25/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
25
Calculate the value of x to have the axial clearancebetween bearing and the shaft, as 1.25 0.25 mm
7/27/2019 Tolerance Accumulation
26/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
26
Considering LL as reference
The value of X must lie as the difference between the sum of thedimension of B, C, D, and E to A.
L
L
7/27/2019 Tolerance Accumulation
27/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
27
EQUATION :
x2 +0.0 +0.00 +0.25 +0.00 +0.25
x1 -0.05 -0.10 -0.25 -0.05 -0.25
X = 5 + 140 + 1.25 + 5 - 100
x2 x2 x2
x1 x1 x1X = ( 151.25100 ) = ( 51.25 )
x2 = + 0.0 + 0.00 + 0.25 + 0.00(0.25 ) = + 0.5
x1 = 0.050.10.250.05( + 0.25 ) = 0.7
x2 +0.5
x1 -0.7(51.25) = 51.25
Verification:Tb+Tc+Td+Te+Ta = TxTb+Tc+Td+Te+Ta = +0.05 + 0.1 + 0.25 +0.25+0.05 +0.25 + 0.25 =1.2
Tx = 1.2
1.2 =1.2
7/27/2019 Tolerance Accumulation
28/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
28
A hole 16H6 has to be drilled and reamedThe dimension is 79 0.1 from one side of the component.Calculate the tolerance for the dimension 12 from one end in abox jig plate to obtain the resultant dimension 79 0.1
7/27/2019 Tolerance Accumulation
29/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
29
+0.00 x2
0.1 0.05 - 0.05 x179 = 111 20 12
Max. limit : + 0.1 = + 0.05(0.05 )x1
x1 = 0Min. limit : 0.1 = - 0.05( + 0 )x2
x2
= 0.05
+ 0.05 +0.00
+ 0.00 - 0.05
The tolerance for the dimension 12 is 12 or 12.05
Verification: Td
= Ta
+ Tb
+ Tc
+ 0.0 + 0.05
0.01 0.05 0.05 - 0.00
79 = 111 - 20 12
Td = 0.2
Ta
+ Tb
+ Tc= (0.05)-(-0.05)+0.0-(-0.05)+(0.05)-(-0.0)
= 0.2
0.2 = 0.2
7/27/2019 Tolerance Accumulation
30/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
30
A hole of 16H7 is to be made with reference to anotherpredrilled and reamed hole 10H7 which lies on a perpendicularplane
The dimension of the hole 10H7 with reference to one side ofthe box jig is given as 245 0.05
Calculate the tolerance for the dimension 97 to position thedrill jig bush to drill and ream dia 16H7 hole.
7/27/2019 Tolerance Accumulation
31/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
31
x2
Dimension should be 148 0.1 = 245 0.0597 x1x2
x1
148 0.1 + 97 = 45 0.05+0.1( x1 ) = + 0.05
x1 = + 0.05
0.1( x2 ) =0.05
x2 =0.05
The tolerances for the dimension 97 is 0.05Verification: 245 0.05 - 97 0.05 = 148 0.1
Ta +Tb = 0.1+ 0.1 = 0.2
Tc = 0.2
0.2 = 0.2
7/27/2019 Tolerance Accumulation
32/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
32
The component shown in Fig. is dimensioned by
two methods. Analyses the more practical one.
In case 1 the dimensions, 50 0.1; 100 0.2 , and theoverall dimensions 180 0.05 are toleranced
In case 2 , dimensions 100 0.2 , 130 0.05and 30 0.05are toleranced .
In case 1 considering LL as the reference
X2
x1X = 180 0.05 50 0.1 100 0.2x2 = + 0.05 - ( - 0.1 ) - ( - 0.2 ) = + 0.35
x1 = - 0.05 - ( + 0.1 ) - ( + 0.2 ) = - 0.35
x2
x1
X = 30 0.35In case 2 considering AA as reference
x2
Xx1 = 130 0.05 - 100 0. 2x2 = + 0.05
- ( - 0.2 ) = + 0.25
x1 =
- 0.05 - ( + 0.2 ) = - 0.25
X2
Xx1 = 30 0. 25
7/27/2019 Tolerance Accumulation
33/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
33
The dimension C from the functional reference LL .
+ 0.08
It is impracticable to measure the depth ( 20 - 0.14 ) of the holehaving diameter D1 from the functional reference LL
Hence the best auxiliary reference selected in this case is MM ,which is also reference for manufacturing. In view of this newreference the dimensions of A, B, C and their tolerances areevaluated as follows.
7/27/2019 Tolerance Accumulation
34/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
34
Nominal dimension ofA = Nominal dimension B+ Nominal dimension C
A = B + C
A = 20 +10 = 30
Total Tolerance ofC = Total tolerance ofA-Total tolerance ofB
The equation will be A - B = C
a2 b2 c2a
1b
1c
1
A - B = C
a2 +0.08
30 a1 10 0.0 5 = 20 - 0.14
a2 (0.05 ) = + 0.08
a2 = 0.08 - 0.05 = + 0.03
a1( + 0.05 ) = 0.14
a1 = 0.09
a2 +0.03
a1 -0.09
A = 30+0.03
The depth of hole is = 30 -0.09.
7/27/2019 Tolerance Accumulation
35/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
35
TOLERANCING DIMENSIONS BETWEEN CENTERS
Methods of dimensioning between centers of holes
Series or chain dimensioning
Parallel dimensioning of each hole with respect to the datum.
Series and Parallel A combination of the above two methods
TOLERANCE ON DIMENSIONS
7/27/2019 Tolerance Accumulation
36/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
36
TOLERANCE ON DIMENSIONS
BETWEEN CENTERS OF TWO HOLES
d is the diameter of the shaftsD is the diameter of holes in two platesA set up for the worst case of interchangeability
Case1: Sizes of the holes and shafts are identical.
7/27/2019 Tolerance Accumulation
37/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
37
1-1 = Axis of holes in the plate1
2-2 = Axis of the holes in the plate 2
CC = Axis of the shafts mating the holes.
M = The distance between the centers of holes m = The tolerance on M on the respective holes
( D-d ) = Clearance between hole and shaft = L
Considering a datum line of no clearance from the figure
The following chain of dimension can be placed keeping in view the signs
An equation for the expression of tolerance is as0 = D/2 - ( M+ m ) + D/2- d+ D/2 + ( M-m ) + D/2 -d
0 = 2D - 2m - 2d
2m = 2 ( D-d )
2m = 2L
m = L
As this is a critical value, m can be less than L but not more, as 100%
interchangeability is to be achieved.
Therefore m = L
7/27/2019 Tolerance Accumulation
38/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
38
If 100% interchangeability is to be achieved in theabove case, the tolerance on dimension between thetwo holes cannot be more than twice the diametricalclearance between the holes and shafts. It could be lessor equal to the clearance.
CONCLUSION
TOLERANCE ON DIMENSIONS BETWEEN CENTERS OF TWO HOLES
7/27/2019 Tolerance Accumulation
39/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
39
Case II: The size of the holes and shafts vary
TOLERANCE ON DIMENSIONS BETWEEN CENTERS OF TWO HOLES
D1 be the diameter of the holes in plates 1 and 2, for the mating shaft d1.D2 be the diameter of the holes in plates 1 and 2 for the mating shaft d2 .A worst case set-up for 100% interchangeability is shown.
7/27/2019 Tolerance Accumulation
40/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
40
1-1 = Axis of holes in the plate 1
2-2 = Axis of holes in the plate 2
c1
-c1
= Axis of the shaft of diameter d1
c2 -c2 = Axis of the shaft of diameter d2
M = The distance between the centers of holes
m = The tolerance on M.
( D1- d1 ) , ( D2 - d2 ). = The clearance between the holes and
Shafts.
Starting from a point of no clearance, a set of chain dimensions can beplaced as follows, keeping in view the directional sign and equating it
to zero.
0 = D2/ 2 - ( M + m ) + D1/ 2 - d1 + D1/2 + ( M - m ) + D2/ 2 - d2
0 = - 2m + ( D1 + D2 ) - ( d1 + d2 )2m = ( D1 - d1 ) + ( D2 - d2 )
2m = ( L1 + L2 ).
Since ( D1 - d1 ) = L1 and ( D2 - d2) = L2m = ( L1 + L2 ) 2
7/27/2019 Tolerance Accumulation
41/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
41
The critical tolerance m on the centers of two holes inthe above case should be equal to half the sum of clearancesin both holes and could be less for 100% interchangeabilitybetween the two plates.
CONCLUSION
TOLERANCE ON DIMENSIONS BETWEEN CENTERS
7/27/2019 Tolerance Accumulation
42/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
42
TOLERANCE ON DIMENSIONS BETWEEN CENTERSOF THREE HOLES
D - is the diameter of holes in the plates 1 and 2
d - the diameter of mating shafts
The holes displaced according to the tolerance for the worstcase, is shown.
Series Dimensioning
7/27/2019 Tolerance Accumulation
43/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
43
1-1 = Axis of the holes in plate 1
2-2 = Axis of the holes in plate 2
c-c = Axis of the shafts
M = Dimension between holesm = The tolerance of the dimensions.
0 = D/2 + ( M- m ) + ( Mm ) + D / 2d + D/2 - ( M+ m )- ( M + m ) +D/2 - d
0 = 2D - 2d - 4m
4 m = 2 ( Dd ) = 2 L. Since ( D - d ) = L
m = L/2
Similarly
For 4 holes dimensioned in series m=L/3
For 5 holes dimensioned in series m=L/4
If n holes are in series m= L/n-1
For n holes dimensioned in series tolerance between the holes should be equal
to
or less than L/n-1 for 100% interchangeability.
Series or Chain dimensions between
7/27/2019 Tolerance Accumulation
44/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
44
For n holes dimensioned in series tolerance between the holes
should be equal to or less than L/n-1 for 100% interchangeability.
Series or Chain dimensions betweencenters
7/27/2019 Tolerance Accumulation
45/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
45
As the number of holes increases in case of series dimensioning,
the tolerance, between the holes decreases. Hence the cost of
production increases and it is difficult to make. If same tolerancesare given to the large dimensions as that of small dimensions, it
will be in many instances impracticable.
CONCLUSION
TOLERANCE ON DIMENSIONS BETWEEN CENTERS
7/27/2019 Tolerance Accumulation
46/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
46
TOLERANCE ON DIMENSIONS BETWEEN CENTERSOF THREE HOLES
Parallel Dimensioning
D - is the diameter of holes in the plates 1 and 2
d - is the diameter of the shafts
Fig . shows the holes displaced according to the tolerances for the worst case.
7/27/2019 Tolerance Accumulation
47/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
47
1-1 = Axis of holes in plate 1
2-2 = Axis of holes in plate 2
c-c = Axis of the shafts
M1 = The distance of the second hole from the first
M2 = The distance of the third hole from the first
m = The tolerance of M1 dimension
m = The tolerance of M2 dimension
Considering a datum line of no clearance from the figure the followingchain of dimensions can be laid down taking care of the signs of the
dimensions, the expression for the tolerances is, as follows.
-d+D/2+(M1-m)+D/2-d+D/2-(M1+m)+(M2+m)-D/2+d-D/2-(M2-m)-D/2+d= 0
2 m 2 m = 0m = m
7/27/2019 Tolerance Accumulation
48/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
48
Parallel Dimensioning
7/27/2019 Tolerance Accumulation
49/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
49
As the number of holes increases the tolerance remains the same L
The tolerance between the first hole and second hole is equal to
tolerance between the first hole and third hole. We also conclude that,if the tolerance is equal, it has no bearing on the number of holes .
CONCLUSION
7/27/2019 Tolerance Accumulation
50/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
50
FOUR-HOLE GROUP WITH COORDINATE TOLERANCES
7/27/2019 Tolerance Accumulation
51/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
51
Comparison between series & parallel Dimensioning:
If the number of holes exceeds 3, parallel dimensioning is only
recommended. By series dimensioning, tolerance decreases which isdifficult to achieve and expensive.
TOLERANCE ON DIMENSIONS OF HOLES IN PLATES I AND
7/27/2019 Tolerance Accumulation
52/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
52
TOLERANCE ON DIMENSIONS OF HOLES IN PLATES I ANDII FROM THEIR COMMON EDGE FOR INTERCHANGEABILITY:
Case1: Fastener having clearance in both the plates
Two plates are to be assembled by a fastener ofdiad, passing through the holes
of dia D.
The locations of holes are with reference to the common edge 0.
The distance of the holes from the common edge is M m , where m is the
tolerance.
7/27/2019 Tolerance Accumulation
53/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
53
Center of the hole in plate 1 is ( M + m )
Center of the hole in plate 2 is ( Mm )
In the plan view a line joining the common edge and the centers makes
an angle of 45 degrees and the figure shows the respective distance
from the common edge.
Applying the principles as before,
0 = (D/2)-2 (M+m) +2(M-m) + (D/2)-d0 = (D-d) - 2 2m, Therefore 2*2m = (Dd)
( Dd ) = L
2m = ( Dd ) 2 = 0.7 * L
TOLERANCE ON DIMENSIONS OF HOLES IN PLATES I AND
7/27/2019 Tolerance Accumulation
54/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
54
TOLERANCE ON DIMENSIONS OF HOLES IN PLATES I ANDII FROM THEIR COMMON EDGE FOR INTERCHANGEABILITY:
Case II: Fastener having clearance in plate 1 and press fit in plate 2.
For the position as shown
0 = (D/2)-2(M+m)+2(M-m)-(d/2)(D-d)/2 = 2*2m ; ( Dd ) = L0.35 L = 2m.
TOLERANCES OF DIMENSIONS IN TWO PLATES FROM
7/27/2019 Tolerance Accumulation
55/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
55
COMMON SURFACE FOR INTERCHANGEABILITY
DDia. of hole in Plates 1 & 2
( M + m ) and ( Mm ) - distance of holes
ddia. of fastener
Case I : Fastener having clearance in both plates
Applying the principle
0 = ( D/2 ) ( M + m ) + ( M - m ) + ( D/2 )d
Dd = 2 m
Dd = L,
L = 2m0.5 L = m
for complete interchangeability
m 0.5 L
TOLERANCES OF DIMENSIONS IN TWO PLATES FROM
7/27/2019 Tolerance Accumulation
56/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
56
Case II: Fastener having clearance in one plate and press fit in other plate
COMMON SURFACE FOR INTERCHANGEABILITY
0 = D / 2 - ( M + m ) + ( Mm ) ( d / 2 )
( Dd ) / 2 = 2 m
( Dd ) = LL / 2 = 2 m
m = 0.25 L
For complete interchangeability m 0.25
CALCULATION OF TOLERANCE FOR DISTANCE BETWEENHOLES ON DRILL JIGS
7/27/2019 Tolerance Accumulation
57/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
57
HOLES ON DRILL JIGS
Two holes are to be drilled and reamed at a distance W0 within the limits T0 , by using a jig
plate with slip bushes as shown in Fig.
W1 T1 be the distance between the liner bushes in jig plate.L1, L2 = Clearance (around) between the slip bush and liner bush for the first and second
holes respectively.
e1, e2 = eccentricity of inside diameter of slip bush with respect to its outside diameter for the
two bushes respectively.
So that W0 = f ( w1, L1, L2, e1, e2.).
7/27/2019 Tolerance Accumulation
58/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
58
CONDITION 1:
When the distance between liner bushes in the jig plate is at maximum
distance (W1+T1) and slip bushes at far off position.
O1, O2 are centers of the slip bushes which are eccentric with respect to their
outside diameter of slip bushes by e1 and e2.
OO1 = L1 + e1OO2 = L2 + e2.
This distance between holes on the component
W 1 + T1 + OO1 + OO2
The sum of these distance should be less than the maximum distance givenon the component.
( W1 + T1 + L1 + e1 + e2 ) W0 + T0.
CONDITION 2:
7/27/2019 Tolerance Accumulation
59/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
59
CONDITION 2:
When the distance between liner bushes in jig plate is at minimum distance (W1-T1)
and when slip bushes are also at minimum distance:
O1, O2 are the centers of the slip bushes, which are eccentric with respect to outside
by e1 and e2 respectively.
OO1
= L1
+ e1
OO2 = L2 + e2
The distance between the holes obtained on the component
( W1 + T1 ) = ( W1 - T1 ) - O O1 - OO2= ( W
1- T
1) - ( L
1+ e
1) - ( L
2+ e
2)
= ( W1 - T1 - L1 - L2 - e1 - e2 )
The sum of these distances should be more than the minimum distance( W
o- T
o) given on the component
( W1- T
1) - L
1- L
2- e
1- e
2 ( W o - To )
EFFECT OF CLEARANCE BETWEEN THE DRILL AND THE SLIP BUSHES ONDISTANCE BETWEEN THE HOLES ON THE COMPONENT
7/27/2019 Tolerance Accumulation
60/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
60
DISTANCE BETWEEN THE HOLES ON THE COMPONENT
Case I : The drill size is minimum , bushes and the drill are at far off position
O1, O2 are the positions of the centres of the slip bush when the clearance between the
drill and the slip bush are considered.
With the effect of clearance between the drill and the slip bushes, the maximum
extreme dimension obtained is as
= W1
+ T1+ L
1+ L
2+ e
1+ e
2+ OO
1+ OO
2
= W1 + T1 + L1 + L2 + e1 + e2 + ( d b + Tb ) - ( d - Td )
The sum of these distances should be less than or equal to Wo + To.
7/27/2019 Tolerance Accumulation
61/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
61
CASE II: When drill size is minimum the bushes position is also at minimum
distance , the drill is at minimum distance.
OO1
= OO2
= ( db
- Tb
) - ( d - Td
) 2
Actual distance between holes on component
= W1- T
1- L
1- L
2e
1- e
2- OO
1- OO
2
= W1- T
1- L
1- L
2- e
1- e
2- ( d
b+ T
b) + ( d - T
d)
This should be more than the minimum distance ( W0- T
0) given on component.
W1- T
1- L
1- L
2- e
1- e
2- ( d
b+ T
b) - ( d - T
d) > W
0- T
0
Final conditions are
W1+ T
1+ L
1+ L
2+ e
1+ e
2+ ( d
b+T
b) - ( d - T
d) ( W
0+ T
0)
W1- T
1- L
1- L
2- e
1e
2- ( d
b+ T
b) + ( d - T
d) > ( W
0- T
0)
As per Indian standard the tolerance on drill is = h 9
The tolerance of the hole in slip bush is = F7
The clearance between the liner bush and the slip bush is = F7/ h
6
(If the liner bush is used for drilling also)
7/27/2019 Tolerance Accumulation
62/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
62
7/27/2019 Tolerance Accumulation
63/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
63
1
2
7/27/2019 Tolerance Accumulation
64/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
64
7/27/2019 Tolerance Accumulation
65/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
65
3
7/27/2019 Tolerance Accumulation
66/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
66
4
7/27/2019 Tolerance Accumulation
67/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
67
6
7/27/2019 Tolerance Accumulation
68/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
68
DRAWING
7/27/2019 Tolerance Accumulation
69/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
69
DRAWING
7/27/2019 Tolerance Accumulation
70/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
70
10
7/27/2019 Tolerance Accumulation
71/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
71
20
7/27/2019 Tolerance Accumulation
72/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
72
30
7/27/2019 Tolerance Accumulation
73/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
7340
7/27/2019 Tolerance Accumulation
74/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
74
50
7/27/2019 Tolerance Accumulation
75/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
75
60
7/27/2019 Tolerance Accumulation
76/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
7670
7/27/2019 Tolerance Accumulation
77/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
77
80
7/27/2019 Tolerance Accumulation
78/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
78
90
7/27/2019 Tolerance Accumulation
79/80
THE INSTITUTE FOR ENHANCEMENT OF TECHNOLOGY
79
100
7/27/2019 Tolerance Accumulation
80/80
Top Related