The smart way to dry air: The BOGE adsorption dryer D 20 A.
Flow capacity: 2.07 m³/min, 73 cfm Max. operating pressure: 16 bar, 232 psig
EFFICIENT DRYING. The BOGE D 20 A allows the com-
pressed air to be dried in a very
effi cient manner. An optional
dewpoint controller reduces the
number of regeneration cycles by
constantly measuring the dewpoint
and by decreasing regeneration
during partial load operation. This
saves regeneration air and energy
at the same time.
CONVENIENT MAINTENANCE. With just a few turns the cartridge
in the BOGE D 20 A can be re-
placed– that‘s all. The cartridge
contains both pre-fi lter and after-
fi lter as well as the desiccant.
Gone are the laborious days when
the desiccant had to be cleaned
out and then refi lled.
SILENT OPERATION. The BOGE D 20 A operates ex-
tremely quietly: A novel sound ab-
sorbing feature reduces the ex-
haust air noise to max. 60 dB(A).
Exhaust air sound pressure values
exceeding 70 dB(A), commonplace
with current adsorption dryers, are
now a thing of the past.
SAFE OPERATION. Damage to the desiccant due to
bulk water is impossible with the
BOGE D 20 A because a water
separator at the air inlet reliably
intercepts the water and prevents
it from fl owing into the cartridge
and contaminating the media.
Maintenance easier than ever:
Simply replacing a cartridge
is all that’s necessary!
a
b
c
d
e
f
BOGE KOMPRESSOREN
Otto Boge GmbH & Co. KG
P. O. Box 10 07 13 · 33507 Bielefeld
Otto-Boge-Straße 1–7 · 33739 Bielefeld
phone +49 5206 601-0
fax +49 5206 601-200
[email protected] · www.boge.com
347-
GB-1
.5-0
3.20
11/B
· T
echn
ical
cha
nges
and
erro
rs re
serv
ed.
OVERVIEW OF THE BOGE D A SERIES:
After the drying process the air passes through
a particle fi lter (d) which is designed
to collect any residual dirt or dust particles
so that the air produced conforms to quality
Class 2 according to DIN ISO 8573.1.
The volume fl ow regulator (e) controls the fl ow
of compressed air and prevents any overloading
of the dryer and affecting the pressure
dewpoint.
Simultaneous to the drying process a small
portion of the dried compressed air is directed
through the other chamber (f) to desorb the
media.The desiccant is therefore regenerated
without any additional energy consumption.
The D A series is equipped with two towers:
Whilst one tower is adsorbing humidity the other
one is regenerating the desiccant.
Saturated compressed air leaving the compressor
enters the inlet (a) of one of the towers and
through the pre-fi lter/water separator (b) collecting water in a special condensate
chamber this prevents any bulk water migration
into the desiccant media. This water is then
separated during regeneration of the reservoir.
Subsequently, the air passes through the
desiccant (c) which adsorbs the remaining
water vapour from the air.
BOGE Type
Volume of fl ow Connection WidthW
HeightH
DepthD
Weight
m3/min cfm mm mm mm kgD 1 A 0.09 3 G ¼ 241 447 160 8,3
D 2 A 0.14 5 G ¼ 241 447 160 8,3
D 3 A 0.31 11 G ¼ 241 647 160 13
D 5 A 0.45 16 G ¼ 241 897 160 16
D 7 A 0.74 26 G ¼ 241 1097 160 19
D 10 A 1.06 37 G 3/8 440 734 295 40
D 13 A 1.30 46 G 3/8 440 734 295 40
D 16 A 1.64 58 G ½ 440 914 295 54
D 20 A 2.07 73 G 1 440 914 295 54
D 28 A 2.75 97 G 1 440 1089 295 64
D 33 A 3.29 116 G 1 440 1239 295 78
D 40 A 4.12 145 G 1 440 1489 295 95D 55 A 5.51 195 G 1 440 1839 295 119
Safe, effi cient and uniquely convenient: The Boge D A series adsorption dryer will inspire you in all aspects. Because of its cartridge system, maintenance is now no more than a child‘s play. And thanks to its safe and effi cient design it reliably produces dry air to Class 2 quality according to DIN ISO 8573.1 – ideally suited for medical technology or the food industry up to a compressor output of approx. 5.5 m³/min.
Top Related