The Articulator
2961AGC/2973AGC
Parts ManualManual Part #: Man-2961AGC
LASTEC7865 N County Road 100E
Lizton, Indiana 46149
Phone (317) 892-4444 Fax (317) 892-4188 www.lastec.com
8 Lastec, 2008
Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any photographic, electronic, mechanical or other means or used in any information storage and retrieval system without written permission from
Lastec, Inc.7865 N. County Road 100E
Lizton, IN 46149
Table of Contents Section-Page
SECTION 1 GENERAL INFORMATION 1-1
1.1 How To Use The Parts List ....................................................................................... 1-21.2 Torque Values ........................................................................................................... 1-31.3 Decals ........................................................................................................................ 1-41.4 Hardware Kit (CE Only) ........................................................................................... 1-9
SECTION 2 DRIVE SYSTEM 2-1
2.1 Seat Assembly .......................................................................................................... 2-22.2 Roll-Over Protection System (ROPS) ....................................................................... 2-42.3 Rocker Assembly (Serial # 2130406 and prior) ........................................................ 2-62.4 Rocker Assembly, 61” Deck (Serial # 2140406 and later) ....................................... 2-82.5 Rocker Assembly, 73” Deck ................................................................................... 2-102.6 Left Rocker Deck Lift Assembly, 61” Deck (Prior to Serial #54410615) .............. 2-122.7 Right Rocker Deck Lift Assembly, 61” and 73” Decks (Prior to Serial #54410615)2-142.8 Left Rocker Deck Lift Assembly, 73” Deck (Prior to Serial #54410615) .............. 2-162.9 Rocker Wheel Assembly ......................................................................................... 2-182.10 Wheel Yoke Assembly ............................................................................................ 2-202.11 Wheel Assembly, 13 x 6.50 x 6............................................................................... 2-222.12 Hand Contol Assembly............................................................................................ 2-242.13 Control Box Assembly ............................................................................................ 2-262.14 Pedal Assembly (Optional as of serial #26270307) ................................................ 2-282.15 Throttle Assembly (Deleted after Serial # 24321106) ............................................ 2-302.16 Front Deck Lift Rod Assembly (Serial #24311106 and prior)................................ 2-322.17 Front Deck Lift Rod Assembly (Serial #24331106 and later) ................................ 2-342.18 Emergency Brake Assembly ................................................................................... 2-362.19 Rear Deck Lift Rod Assembly ................................................................................ 2-382.20 Framework............................................................................................................... 2-402.21 Pull Bar Assembly................................................................................................... 2-422.22 Roller Assembly Upgrade Kit (Optional)................................................................ 2-442.23 Striping Kit (Optional) ............................................................................................ 2-46
SECTION 3 HYDRAULIC SYSTEM 3-1
3.1 Hydraulic Layout Diagram (Serial #46570113 and later) ......................................... 3-23.2 Hydraulic Layout Diagram (Prior to Serial #46570113)........................................... 3-43.3 Hydraulic Pump Assemblies ..................................................................................... 3-63.4 Hydraulic Motor, Right ............................................................................................. 3-83.5 Hydraulic Motor, Left ............................................................................................. 3-103.6 Brake Assembly....................................................................................................... 3-123.7 Hydraulic Tank Assembly (Serial #46570113 and later) ........................................ 3-143.8 Hydraulic Tank Assembly (Priot to Serial #46570113) .......................................... 3-163.9 Hydraulic Drive Idler Assembly ............................................................................. 3-18
3 Lastec//072815 Table of Contents
Table of Contents Section-Page
SECTION 4 ENGINE & ELECTRICAL 4-1
4.1 Fuel Tank Assembly (Serial #46570113 and later)................................................... 4-24.2 Fuel Tank Assembly (Serial #25620207 to #46560113)........................................... 4-44.3 Fuel System ............................................................................................................... 4-64.4 Engine Guard Assembly............................................................................................ 4-84.5 Engine Assembly..................................................................................................... 4-104.6 Radiator Cowling Assembly.................................................................................... 4-124.7 Motor Mount and Hardware.................................................................................... 4-144.8 Deck Drive Idler Assembly ..................................................................................... 4-164.9 Air Filter Assembly ................................................................................................. 4-184.10 Battery Tray Assembly............................................................................................ 4-204.11 Wiring Harness ....................................................................................................... 4-22
SECTION 5 61” MOWER DECK 5-1
5.1 Deck Framework ....................................................................................................... 5-25.2 Deck 1 Hardware (Serial # 2860806 and later) ......................................................... 5-45.3 Deck 1 Hardware (Serial # 2850806 and prior) ........................................................ 5-65.4 Deck 2 Hardware....................................................................................................... 5-85.5 Deck 3 Hardware..................................................................................................... 5-105.6 Rear Discharge Baffle Assembly ............................................................................ 5-125.7 Optional Mulching Kit ............................................................................................ 5-145.8 Double Pulley Spindle (5/14 and later) ................................................................... 5-165.9 Spindle Housing ..................................................................................................... 5-185.10 Double Pulley Spindle (Prior to 5/14) ..................................................................... 5-205.11 Spindle Housing ...................................................................................................... 5-225.12 Tensioner Assembly ................................................................................................ 5-245.13 Grass Chute ............................................................................................................. 5-265.14 Rear Anti-scalp Roller (Prior to 5/14) ..................................................................... 5-28
SECTION 6 73” MOWER DECK 6-1
6.1 Deck Framework ....................................................................................................... 6-26.2 Deck 1 Hardware....................................................................................................... 6-46.3 Deck 2 Hardware....................................................................................................... 6-66.4 Deck 3 Hardware....................................................................................................... 6-86.5 Double Pulley Spindle, Decks 1 and 3 (8/14 and later) ......................................... 6-106.6 Spindle Housing, Decks 1 and 3 (8/14 and later) .................................................... 6-126.7 Double Pulley Spindle, Decks 1 and 3 (Prior to 8/14) ............................................ 6-146.8 Spindle Housing ...................................................................................................... 6-166.9 Tensioner Assembly ................................................................................................ 6-186.10 Deck 2, Double Pulley Drive Spindle (8/14 and later)............................................ 6-206.11 Deck 2, Double Pulley Drive Spindle (Prior to 8/14) ............................................. 6-226.12 Grass Chute ............................................................................................................. 6-246.13 Rear Anti-scalp Roller (Prior to 8/14) ..................................................................... 6-26
Table of Contents Lastec//072815 4
Table of Contents Section-Page
SECTION 7 INDEX 7-1
Table of Contents Lastec//072815 5
Mower//072815 1-1
1
SECTION 1 GENERAL INFORMATION
General InformationHow To Use The Parts List
General Information Mower//072815 1-2
1
1.1 How To Use The Parts List
Use the table of contents or part number index to locate the part you need.
Go to the appropriate section and locate the part in the table and illustration.
Parts shown indented under another part are included with that part. IMPORTANT:Assemblies marked with a diamond () are non-saleable and all the parts shown as included need to be purchased separately.
See the sample table below. Sample Assembly A01111 includes part F02222-22 and sub-assembly A03333. The diamond () indicates that assembly A01111 is non-saleable and all the parts shown as included need to be purchased separately. Subassembly A03333 includes parts S04444-4 and F07777-77. The diamond () indicates that subassembly A03333 is non-saleable and all the parts shown as included need to be purchased sepa-rately.
To Order Parts:
From the continental U.S., call your local Lastec distributor to order parts. If there is no Lastec distributor in your area, call 1-800-515-6798. Have your customer num-ber, unit serial number, and part numbers ready when you call.
From other international locations, contact the Lastec distributor in your area for parts.
REF PART # DESCRIPTION (Indicates Non-Saleable Items) COMMENTS QTY.
A01111 Sample Assembly 1
1 F02222-22 Sample Part 1
A03333 Sample Subassembly 1
2 S04444-4 Sample Part 1
3 F07777-77 Sample Part 1
General InformationTorque Values1
1-3 Mower//072815 General Information
1.2 Torque Values
Below is a table of suggested torque values for this unit. Please use these torque values
on this unit unless otherwise specified.
Grade Units SAE 5 SAE 8
Tensile
Strength
105000
PSI150000
PSI
Grade Mark
Bolt
Dia.
Threads.
Per In.Units SAE 5 SAE 8
6
8
10
10
12
1/4
1/4
5/16
5/16
3/8
3/8
7/16
7/16
1/2
1/2
9/16
9/16
5/8
5/8
3/4
3/4
7/8
7/8
1
32
32
24
32
24
20
28
18
24
16
24
14
20
13
20
12
18
11
18
10
16
9
14
8
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
20 (2.3)
24 (2.7)
35 (4.0)
40 (4.5)
50 (5.7)
95 (10.7)
95 (10.7)
17 (22.6)
20 (27.1)
30 (40.7)
35 (47.5)
50 (67.8)
55 (74.6)
75 (101.7)
85 (115.3)
105 (142.4)
115 (155.9)
150 (203.4)
160 (217.0)
170 (230.5)
175 (237.3)
302 (409.5)
300 (406.8)
466 (631.8)
-
30 (3.4)
45 (5.1)
50 (5.7)
65 (7.3)
125 (14.1)
150 (17.0)
23 (31.2)
25 (33.8)
40 (54.2)
45 (61.0)
65 (88.1)
70 (94.9)
100 (135.6)
110 (149.2)
135 (183.1)
150 (203.4)
195 (264.4)
210 (284.8)
220 (298.3)
225 (305.1)
473 (640.9)
400 (542.4)
714 (967.4)
General InformationDecals 1
1.3 Decals
Decals (US Only)
REF PART # DESCRIPTION COMMENTS QTY.
055843 Decal Kit, 2961AGC 61” Deck Only 1
055847 Decal Kit, 2973AGC 73” Deck Only 1
1 049747 Decal, Comm Mower Control Panel Gas 1
2 028601 Decal, Fwd/Rev Motion 2
3 049930 Decal, Belt Routing Diagram 1
4 048227 Decal, Hydro Fill Line 1
5 019554 Decal, Warning, Operational Safety 425D 1
6 040911 Decal, Warning Operate With Guards 2
7 056591 Decal, 18 PSI 2
8 014419 Decal, Hot Engine Warning 1
9 042003 Decal, Warning, Slope 1
10 062404 Decal, AGC/ADC Hydro 1
11 040912 Decal, Danger, Thrown Objects/Arrow 1
12 045519 Decal, Sound Power Level 1
062425 Decal, Relays for 055700-055846 Not Shown 1
019552 Decal, Caution Clean Radiator Not Shown 1
13 041200 Decal, Fuel Switch 421D 1
14 044731 Decal, Control Box Engine Throttle 1
15 049466 Decal, Comm. Deck Height Adjustment 1
16 028603 Decal, Brake Control 1
17 043225 Decal, Flat World Logo 1
18 P478 Decal, Danger - Rotating Blades 2
19 062429 Decal, Lastec Made in USA 1
20 040910 Decal, Warning Operate From Seat 2
21 048504 Decal, Lastec, Roll Bar 1
22 019557 Decal, Articulator Logo Div WM 1
23 049619 Decal, 2961AGC Articulatot Large 61” Deck Only 2
049620 Decal, 2973AGC Articulator Large 73” Deck Only 2
24 049931 Decal, 61 Inches 61” Deck Only 2
049465 Decal, 73 Inches 73” Deck Only 2
P485 Decal, Fuel Equipment 325E Not Shown 2
General Information Lastec//072815 1-4
General InformationDecals1
WARNING
042003
Fuel Control Valve
OffRig
ht
Tank
Left Tank
WARNING
Without all safety shields and guards in place
at all times.
AVOID SERIOUS INJURY OR DEATH
040911
Burn Hazard
Avoid contact with any part of hot engine.
Failure to do so may result in serious injury.
Wood-Mizer Products, Inc.800-525-8100 Reorder #014419
DANGER THROWN OBJECTS
Before mowing clear area of people and objects which
may be thrown by blades.
ROTATING BLADES Do not put hands or feet under
or into mower when engine is running. 040912
WARNING
Without all safety shields and guards in place
at all times.
AVOID SERIOUS INJURY OR DEATH
040911
WARNING Operate from operator
seat only. Follow all safety rules in
owner manual during operation or maintenance.
AVOID SERIOUS INJURY OR DEATH
040910
Fill Line
048227
Belt Routing 049930
Fill Tire to:
18 psi056591
Fill
Tire
to:
18 p
si
0565
91
This unit uses hydraulic fluid
Hydraulic Filter
(uses 2 filters/mower)
Hydraulic Fluid (1qt)
2.5 gal Service Kit (includes 2 filters)
5.0 gal Service Kit (includes 4 filters)
ITEM PART #
P620
040642
049929
049928
062404
Under Seat PanOn Hydraulic Tank
LT0126
OROR
Center of Rear Bumper
73” 73”
1-5 Lastec//072815 General Information
General InformationDecals 1
Decals (CE Only)
REF PART # DESCRIPTION COMMENTS QTY.
055843 Decal Kit, 2961AGC 61” Deck Only 1
055847 Decal Kit, 2973AGC 73” Deck Only 1
1 049747 Decal, Comm Mower Control Panel Gas 1
2 028601 Decal, Fwd/Rev Motion 2
3 049930 Decal, Belt Routing Diagram 1
4 048227 Decal, Hydro Fill Line 1
5 019554 Decal, Warning, Operational Safety 425D 1
6 040911 Decal, Warning Operate With Guards 2
7 056591 Decal, 18 PSI 2
8 014419 Decal, Hot Engine Warning 1
9 042003 Decal, Warning, Slope 1
10 062404 Decal, AGC/ADC Hydro 1
11 040912 Decal, Danger, Thrown Objects/Arrow 1
12 045519 Decal, Sound Power Level 1
062425 Decal, Relays for 055700-055846 Not Shown 1
019552 Decal, Caution Clean Radiator Not Shown 1
13 041200 Decal, Fuel Switch 421D 1
14 044731 Decal, Control Box Engine Throttle 1
15 049466 Decal, Comm. Deck Height Adjustment 1
16 028603 Decal, Brake Control 1
17 043225 Decal, Flat World Logo 1
18 P478 Decal, Danger - Rotating Blades 2
19 062429 Decal, Lastec Made in USA 1
20 040910 Decal, Warning Operate From Seat 2
21 048504 Decal, Lastec, Roll Bar 1
22 019557 Decal, Articulator Logo Div WM 1
23 049619 Decal, 2961AGC Articulatot Large 61” Deck Only 2
049620 Decal, 2973AGC Articulator Large 73” Deck Only 2
24 049931 Decal, 61 Inches 61” Deck Only 2
049465 Decal, 73 Inches 73” Deck Only 2
P485 Decal, Fuel Equipment 325E Not Shown 2
067065 Decal Kit, CE Deck 1
040267 Decal Kit, European Languages 2
040256 Decal, Warning, Outer Decks -- German 1
040257 Decal, Warning, Outer Decks -- French 1
040258 Decal, Warning, Outer Decks -- Italian 1
040259 Decal, Warning, Outer Decks -- Spanish 1
040260 Decal, Warning, Outer Decks -- Danish 1
P117 Decal, Hands & Feet 7
General Information Lastec//072815 1-6
General InformationDecals1
041205 Decal, Thrown Objects CE Std 1
041206 Decal, Caution Symbol CE Std 2
041209 Decal, Keep Away/Rotating Drive Line CE 2
WARNING
042003
Fuel Control Valve
OffRig
ht
Tank
Left Tank
WARNING
Without all safety shields and guards in place
at all times.
AVOID SERIOUS INJURY OR DEATH
040911
Burn Hazard
Avoid contact with any part of hot engine.
Failure to do so may result in serious injury.
Wood-Mizer Products, Inc.800-525-8100 Reorder #014419
DANGER THROWN OBJECTS
Before mowing clear area of people and objects which
may be thrown by blades.
ROTATING BLADES Do not put hands or feet under
or into mower when engine is running. 040912
WARNING
Without all safety shields and guards in place
at all times.
AVOID SERIOUS INJURY OR DEATH
040911
WARNING Operate from operator
seat only. Follow all safety rules in
owner manual during operation or maintenance.
AVOID SERIOUS INJURY OR DEATH
040910
Fill Line
048227
Belt Routing 049930
Fill Tire to:
18 psi056591
Fill
Tire
to:
18
psi 05
659
1
This unit uses hydraulic fluid
Hydraulic Filter
(uses 2 filters/mower)
Hydraulic Fluid (1qt)
2.5 gal Service Kit (includes 2 filters)
5.0 gal Service Kit (includes 4 filters)
ITEM PART #
P620
040642
049929
049928
062404
Under Seat PanOn Hydraulic Tank
LT0128
OROR
Center of Rear Bumper
73” 73”
04120
04120
04120
CE
1-7 Lastec//072815 General Information
General InformationDecals 1
General Information Lastec//072815 1-8
Mower DecksHardware Kit (CE Only)1
1.4 Hardware Kit (CE Only)
Hood Assembly, 29HP Kawasaki CE
Nut Assembly, 3/8-16 Cover Retaining
Rivet, 3/16” Dia x 3/8-1/2” Grip Range Pop
Instruction Sheet, 2961/73 CE Hardware Kit
REF PART # DESCRIPTION COMMENTS QTY.
064521 Kit, 2961/73 CE Hardware 1
1 064468 1
2 064500 6
3 F04203-6 6
IS-0307 1
1-9 Lastec//072815 Mower Decks
Mower DecksHardware Kit (CE Only) 1
290009
Mower Decks Lastec//072815 1-10
Mower//072815 2-1
2
SECTION 2 DRIVE SYSTEM
Drive SystemSeat Assembly2
2.1 Seat Assembly
Seat, Air Ride (Color Gray)
Switch, Seat
Screw, Seat Switch
Seat Belt, 2” ALR/ERI Buckle
Pan Weldment, Seat
Bolt, 3/8-16 x 4 1/2” Hex Head 316 SS
Nut, 3/8-16 Hex Half Nylon Lock 316 SS
Nut, 5/16-18 Nylok Hex
Clamp, 1/4" Wire 13/32” Mtg Hole
Bolt, 5/16-18 x 3/4” Hex Head Grade 5
Bolt, 5/16-18 x 1” Hex Head Grade 5
Washer, 5/16” x 1 1/4” Fender
Cable, Seat Lanyard
Spring, Extension 3/8” x 3”
REF PART # DESCRIPTION COMMENTS QTY.
049590 Seat Assembly, Complete Gas 1
1 P630 1
2 P826 1
3 F412 2
P776 Sold as a pair 1
4 049589 1
5 F05007-244 2
6 F05010-234 2
7 F05010-58 3 Added after Serial # 19403061 Added after Serial # 2960906
7
8 024155 Added after Serial # 2960906 1
9 F05006-102 Added after Serial # 2960906 1
10 F05006-27 3 Added after Serial # 1940306 5
11 F05011-50 3 Added after Serial # 1940306 4
12 045988 Added after Serial # 1940306 2
13 014818 1
052025 Seat Delay Assembly, LasTec Mowers Not Shown 1
2-2 Lastec//072815 Drive System
Drive SystemSeat Assembly 2
LT0064
Drive System Lastec//072815 2-3
Drive SystemRoll-Over Protection System (ROPS)2
2.2 Roll-Over Protection System (ROPS)
Frame Weldment, ROPS
Frame Weldment, Comm. ROPS Lower
Frame Weldment, Comm. ROPS Lower
Knob w/Stud, 3/8-16 x 1.50”
Nut, 3/8-16 Hex Nyloc
Pull Pin, 1/2”
Bolt, 1/2-13 x 3” Hex Head Grade 5
Washer, 1.50” OD x .53” ID UHMW
Nut, 1/2-13 Nylon Hex Lock
Bolt, 3/8-16 x 4” Hex Head Grade 5
Washer, 3/8” Flat SAE
Bolt, 3/8-16 x 2 3/4” Hex Head Grade 5
REF PART # DESCRIPTION COMMENTS QTY.
049796 ROPS Assembly, 2861 Folding 1
1 049831 1
1 ROPS framing members may not be sold separately. When ordering, you will receive all three frame weldments (049831, 049736 and 049736-1).
1
2 0497361 1
3 049736-11 1
4 049447 2
5 F05010-10 10
6 049448 2
7 F05008-23 2
8 049446 4
9 F05010-8 2
10 F05007-126 4
11 F05011-3 4
12 F05007-206 4
2-4 Lastec//072815 Drive System
Drive SystemRoll-Over Protection System (ROPS) 2
LT0065
Drive System Lastec//072815 2-5
Drive SystemRocker Assembly (Serial # 2130406 and prior)2
2.3 Rocker Assembly (Serial # 2130406 and prior)
NOTE: Left and right Rockers are mirror images of each other. Be sure to order the cor-rect weldment or cover for the side needed. (Left side shown in illustration.)
REF PART # DESCRIPTION COMMENTS QTY.
1 F05005-79 Bolt, 1/4-20 x 1/2” Hex Head Cap 4
2 F05011-14 Washer, 1/4” Split Lock 4
3 F05011-11 Washer, 1/4” SAE Flat 4
4 049791 Cover, Left Rocker 1
049792 Cover, Right Rocker 1
5 F05009-10 Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 1
6 F05008-106 Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5 1
7 F05010-185 Nut, 5/8-11 Flexloc 3
8 F05010-8 Nut, 1/2-13 Nyl Hex Lock 1 added after serial # 1660206 4
9 F05008-23 Bolt, 1/2-13 x 3” Hex Head Grade 5 Zinc 2
10 F05009-37 Bolt, 5/8-11 X 3” Hex Head Grade 5 Zinc 2
11 049710 Rocker Weldment, Left 61” deck 1
049717 Rocker Weldment, Right 1
11 055384 Rocker Weldment, 73” Right 73” Deck 1
055385 Rocker Weldment, 73” Left 1
12 P107 Fitting, 1/4-28 Straight Grease 1
13 049893 Washer, 3 1/2” OD Wave 1
14 048173 Washer, Wheel Damper 1
15 048174 Block, Wheel Yoke Friction 1
16 F05011-5 Washer, 5/8” SAE Flat Added after serial # 1660206 2
17 F05008-35 Bolt, 1/2-13 x 4-1/2” Hex Head Gr5 1
18 043285 Spring, .72” x 2.75” x .105” MW Added after serial # 1660206 1
19 F05010-8 Nut, 1/2-13 Nyl Hex Lock Added after serial # 1660206 1
2-6 Lastec//072815 Drive System
Drive SystemRocker Assembly (Serial # 2130406 and prior) 2
049715
Drive System Lastec//072815 2-7
Drive SystemRocker Assembly, 61” Deck (Serial # 2140406 and later)2
2.4 Rocker Assembly, 61” Deck (Serial # 2140406 and later)
Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5
Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5
Nut, 5/8-11 FlexLoc
Nut, 1/2-13 Nyl Hex Lock
Bolt, 1/2-13 x 3” Hex Head Grade 5
Bolt, 5/8-11 x 3 Hex Head Grade 5
Rocker Weldment, Right
Rocker Weldment, Left
Rocker Weldment, Left
Cap, Hub
Fitting, 1/4-28 Straight Grease
Seal, 1 1/4” ID Trb Bearing
Washer, 3-1/2” OD Wave
Washer, Wheel Damper
Block, Wheel Yoke Friction
Wheel Yoke Assembly, 13” Comm Right
Wheel Yoke Assembly, 13” Comm
Washer, 5/8” SAE Flat
Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5
Bolt, 1/2-13 x 4 1/2” Hex Head Cap Grade 5
Spring, 0.72” x 2.75” x 0.105” MW
Nut, 1/2-13 Hi-Crown Acorn Cap Plated
Nut, 1/2-13 Nylon Hex Lock
Rocker Wheel Assembly, Right
Rocker Wheel Assembly, Left
Lift Assembly, Right Rocker Deck
Lift Assembly, Left Rocker Deck
NOTE: The left and right rocker assemblies are mirror images of each other. Be sure to order the correct rocker weldment, wheel yoke, rocker wheel and deck lift assemblies for the side needed. (Left side shown below.)
REF PART # DESCRIPTION COMMENTS QTY.
055086 Rocker Assembly, Right Right Side Only 1
055085 Rocker Assembly, Left Left Side Only 1
1 F05009-10 1
2 F05008-106 1
3 F05010-185 3
4 F05010-8 3
5 F05008-23 2
6 F05009-37 2
7 055084 Right Side Only 1
055486 Left Side Only. Serial #24441106 and later
1
055083 Left Side Only. Serial #2130406 to 24431106
1
8 P195 1
9 P107 1
10 P191 1
11 049893 1
12 048173 1
13 048174 1
14 049668 Right Side Only. See Section 2.10 1
046477 Left Side Only. See Section 2.10 1
15 F05011-5 2
16 F05008-106 1
1 Bolt, spring and nut reversed orientation after serial #2850806.
Serial #2850806 and later 1
F05008-35 Serial #2850806 and prior 1
17 043285 1
18 F05010-201 Serial #2850806 and later 1
F05010-8 Serial #2850806 and prior 1
19 049745 Right Side Only. See Section 2.9 1
049740 Left Side Only. See Section 2.9 1
20 049790 Right Side Only. See Section 2.7 1
055831 Left Side Only. See Section 2.6 1
2-8 Lastec//072815 Drive System
Drive SystemRocker Assembly, 61” Deck (Serial # 2140406 and later) 2
LT0066
Drive System Lastec//072815 2-9
Drive SystemRocker Assembly, 73” Deck2
2.5 Rocker Assembly, 73” Deck
NOTE: The left and right rocker assemblies are mirror images of each other. Be sure to order the correct rocker weldment, wheel yoke, rocker wheel and deck lift assemblies for the side needed. (Left side shown below.)
REF PART # DESCRIPTION COMMENTS QTY.
055386 Rocker Assembly, 73” Right Right Side Only 1
055387 Rocker Assembly, 73” Left Left Side Only 1
1 F05009-10 Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 1
2 F05008-106 Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5 1
3 F05010-185 Nut, 5/8-11 FlexLoc 3
4 F05010-8 Nut, 1/2-13 Nyl Hex Lock 3
5 F05008-23 Bolt, 1/2-13 x 3” Hex Head Grade 5 2
6 F05009-37 Bolt, 5/8-11 x 3 Hex Head Grade 5 2
7 055384 Rocker Weldment, Right Right Side Only 1
055385 Rocker Weldment, Left Left Side Only 1
8 P195 Cap, Hub 1
9 P107 Fitting, 1/4-28 Straight Grease 1
10 P191 Seal, 1 1/4” ID Trb Bearing 1
11 049893 Washer, 3-1/2” OD Wave 1
12 048173 Washer, Wheel Damper 1
13 048174 Block, Wheel Yoke Friction 1
14 049668 Wheel Yoke Assembly, 13” Comm Right Right Side Only. See Section 2.10 1
046477 Wheel Yoke Assembly, 13” Comm Left Side Only. See Section 2.10 1
15 F05011-5 Washer, 5/8” SAE Flat 2
16 F05008-35 Bolt, 1/2-13 x 4 1/2” Hex Head Cap Grade 5 1
17 043285 Spring, 0.72” x 2.75” x 0.105” MW 1
18 F05010-201 Nut, 1/2-13 Hi-Crown Acorn Cap Plated 1
19 049745 Rocker Wheel Assembly, Right Right Side Only. See Section 2.9 1
049740 Rocker Wheel Assembly, Left Left Side Only. See Section 2.9 1
20 049790 Lift Assembly, Right Rocker Deck Right Side Only. See Section 2.7 1
049726 Lift Assembly, Left Rocker Deck Left Side Only. See Section 2.8 1
2-10 Lastec//072815 Drive System
Drive SystemRocker Assembly, 73” Deck 2
LT0059
Drive System Lastec//072815 2-11
Drive SystemLeft Rocker Deck Lift Assembly, 61” Deck (Prior to Serial #54410615)2
2.6 Left Rocker Deck Lift Assembly, 61” Deck (Prior to Serial #54410615)
Bolt, 3/8-16 x 7” Hex Head Grade 5
Washer, 3/8” Suspension
Bushing, 3/8” Polyurethane Suspension
Spacer, 3/8” Suspension
Nut, 3/8-16 Hex Nyl Lock
REF PART # DESCRIPTION COMMENTS QTY.
055831 Lift Assembly, Left Rocker Deck 1
1 F05007-125 Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5 2
2 048712 Bushing, 1 1/16" Urethane Pivot 2
3 048692 Strap, 1U 2
4 F05011-3 Washer, 3/8” Flat SAE 4
5 F05010-10 Nut, 3/8-16 Hex Nyloc 4
6 055483 Lift Weldment, Left Deck 1
7 F05008-37 Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 2
8 F05011-2 Washer, 1/2” SAE Flat 2
9 P829 Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz 2
10 F05007-126 Bolt, 3/8-16 x 4” Hex Head Grade 5 2
11 049725 Lift Weldment, Deck Tab 1
12 F05005-105 Screw, 1/4-28 x 1/4” BO Socket Head Pt Set 2
049843 Link Assembly, 3/8” Suspension 1
13 N/A Not sold separately 1
14 N/A Not sold separately 4
15 N/A Not sold separately 4
16 N/A Not sold separately 1
17 F05010-10 1
2-12 Lastec//072815 Drive System
Drive SystemLeft Rocker Deck Lift Assembly, 61” Deck (Prior to Serial #54410615) 2
LT0060
Drive System Lastec//072815 2-13
Drive SystemRight Rocker Deck Lift Assembly, 61” and 73” Decks (Prior to Serial #54410615)2
2.7 Right Rocker Deck Lift Assembly, 61” and 73” Decks (Prior to Serial #54410615)
Bolt, 3/8-16 x 7” Hex Head Grade 5
Washer, 3/8” Suspension
Bushing, 3/8” Polyurethane Suspension
Spacer, 3/8” Suspension
Nut, 3/8-16 Hex Nyl Lock
REF PART # DESCRIPTION COMMENTS QTY.
049790 Lift Assembly, Right Rocker Deck 1
1 F05007-125 Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5 2
2 048712 Bushing, 1 1/16" Urethane Pivot 2
3 048692 Strap, 1U 2
4 F05011-3 Washer, 3/8” Flat SAE 4
5 F05010-10 Nut, 3/8-16 Hex Nyloc 4
6 049789 Lift Weldment, Right Deck 1
7 F05008-37 Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 2
8 F05011-2 Washer, 1/2” SAE Flat 2
9 P829 Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz 2
10 F05007-126 Bolt, 3/8-16 x 4” Hex Head Grade 5 2
11 049725 Lift Weldment, Deck Tab 1
12 F05005-105 Screw, 1/4-28 x 1/4” BO Socket Head Pt Set 2
049843 Link Assembly, 3/8” Suspension 1
13 N/A Not sold separately 1
14 N/A Not sold separately 4
15 N/A Not sold separately 4
16 N/A Not sold separately 1
17 F05010-10 1
2-14 Lastec//072815 Drive System
Drive SystemRight Rocker Deck Lift Assembly, 61” and 73” Decks (Prior to Serial #54410615) 2
LT0063
Drive System Lastec//072815 2-15
Drive SystemLeft Rocker Deck Lift Assembly, 73” Deck (Prior to Serial #54410615)2
2.8 Left Rocker Deck Lift Assembly, 73” Deck (Prior to Serial #54410615)
Bolt, 3/8-16 x 7” Hex Head Grade 5
Washer, 3/8” Suspension
Bushing, 3/8” Polyurethane Suspension
Spacer, 3/8” Suspension
Nut, 3/8-16 Hex Nyl Lock
REF PART # DESCRIPTION COMMENTS QTY.
049726 Lift Assembly, Left Rocker Deck 1
1 F05007-125 Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5 2
2 048712 Bushing, 1 1/16" Urethane Pivot 2
3 048692 Strap, 1U 2
4 F05011-3 Washer, 3/8” Flat SAE 4
5 F05010-10 Nut, 3/8-16 Hex Nyloc 4
6 049720 Lift Weldment, Left Deck 1
7 F05008-37 Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 2
8 F05011-2 Washer, 1/2” SAE Flat 2
9 P829 Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz 2
10 F05007-126 Bolt, 3/8-16 x 4” Hex Head Grade 5 2
11 049725 Lift Weldment, Deck Tab 1
12 F05005-105 Screw, 1/4-28 x 1/4” BO Socket Head Pt Set 2
049843 Link Assembly, 3/8” Suspension 1
13 N/A Not sold separately 1
14 N/A Not sold separately 4
15 N/A Not sold separately 4
16 N/A Not sold separately 1
17 F05010-10 1
2-16 Lastec//072815 Drive System
Drive SystemLeft Rocker Deck Lift Assembly, 73” Deck (Prior to Serial #54410615) 2
LT0060
Drive System Lastec//072815 2-17
Drive SystemRocker Wheel Assembly2
2.9 Rocker Wheel Assembly
NOTE: The left and right assemblies are mirror images of each other. Be sure to order the correct weldment for the side needed. (Left side shown below.)
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY.
049745 Rocker Wheel Assembly, Right Right Side Only 1
049740 Rocker Wheel Assembly, Left Left Side Only 1
1 049870 Bushing, Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly. Serial #1660206 and later
2
049510 Bushing, Rubber Pivot Serial #2780806 and prior.No longer available; order 049870
2
2 049744 Weldment, Right Rocker Wheel Pivot Right Side Only 1
049741 Weldment, Left Rocker Wheel Pivot Left Side Only 1
3 F05010-34 Nut, 5/8-11 Nyl Lock 1
4 F05011-5 Washer, 5/8” SAE Flat 1
5 027013 Wheel, Anti-Scalp 5-5/8" hole 1
2-18 Lastec//072815 Drive System
Drive SystemRocker Wheel Assembly 2
LT0061
Drive System Lastec//072815 2-19
Drive SystemWheel Yoke Assembly2
2.10 Wheel Yoke Assembly
REF PART # DESCRIPTION COMMENTS QTY.
046477 Wheel Yoke Assembly, 13” Comm Left Side & Front Only 1
049668 Wheel Yoke Assembly, 13” Comm Right Right Side Only 1
1 P434 Nut, 3/4-16 Castle 1
2 F05011-62 Washer, 3/4” SAE Flat 1
3 P190 Bearing, 1” ID Tapered Roller 1
4 043968 Spacer, Wheel Yoke Bearing 2
5 F05012-79 Pin, 5/32” x 1 1/2” Cotter Serial # 2161105 and later 1
F05012-49 Pin, 1/8” x 1 1/2” Cotter Serial # 2151105 and prior 1
6 046478 Yoke Weldment, 2561 Front Wheel 1
7 F05009-108 Bolt, 3/4-10 x 9” Hex Head Grade 5 1
8 F05010-177 Nut, 3/4-10 Stover Swaged 1
9 045986 Wheel Assembly, 13” x 6.5” x 6” See Section 2.11 1
10 P296 Spacer, 1.13” OD x .75” ID x .5” 2
2-20 Lastec//072815 Drive System
Drive SystemWheel Yoke Assembly 2
LT0054
Valve StemThis Side
(Right SideAssembly Only)
Valve StemThis Side(Left SideAssembly Only)
Drive System Lastec//072815 2-21
Drive SystemWheel Assembly, 13 x 6.50 x 62
2.11 Wheel Assembly, 13 x 6.50 x 6
NOTE: The tire and hub are not sold separately and they are included in Wheel Assembly (045986).
REF PART # DESCRIPTION COMMENTS QTY.
045986 Wheel Assembly, 13” x 6.5” x 6” 1
1 P293 Seal, TRB, 3/4” ID 2
2 P292 Bearing, Tapered Roller, 3/4” ID 2
3 P402 Bearing Race Insert, 3/4" TRB 2
2-22 Lastec//072815 Drive System
Drive SystemWheel Assembly, 13 x 6.50 x 6 2
LT0053
Drive System Lastec//072815 2-23
Drive SystemHand Contol Assembly2
2.12 Hand Contol Assembly
Screw, 1/4-28 x 1/4” BO SH Cup Pt Set
NOTE: Right and Left Control Handle Arm Assemblies are mirror images of each other with the exception of the Control Arm Weldment (item 2).
REF PART # DESCRIPTION COMMENTS QTY.
049706 Arm Assembly, Right Control Handle Right Side Only 1
049707 Arm Assembly, Left Control Handle Left Side Only 1
1 028390 Grip, Handle 1
2 027015 Arm Weldment, 2561 Right Control Right Side Only 1
027016 Arm Weldment, 2561 Left Control Left Side Only 1
3 F05007-87 Bolt, 3/8-16 x 1” Hex Head Grade 5 3
4 F05011-4 Washer, 3/8” Split Lock 2
5 F05011-3 Washer, 3/8” Flat SAE 2
6 048393 Mount, Extended Drive Handle Serial #1940106 and later 1
043950 Block, Drive Handle Mount Serial #1520306 and prior 1
7 P05035 Collar, 5/8” ID Lock 2
8 F05005-105 2
9 014834 Bearing, w/Snap Ring 5/8” ID 2
10 F05010-124 Nut, 3/8-16 Half Nyloc 1
11 F05008-96 Bolt, 5/16-18 x 1 1/2” Hex Head Grade 5 1
12 F05010-58 Nut, 5/16-18 Nylok Hex 1
13 043952 Arm Pivot Weldment, Right Control 1
14 F05010-1 Nut, 3/8-16 Hex 1
15 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 1
056450 Turnbuckle Assembly, Hydro Diesel 1
16 018739 Rod End, 3/8-24 Right Hand 1
17 F05010-123 Nut, 3/8-24 Free 1
18 056449 Rod, Hydro Control Link 1
19 F05010-119 Nut, 5/16-24 Jam LH 1
20 014815 Rod End, 5/16-24 Male LH 1
2-24 Lastec//072815 Drive System
Drive SystemHand Contol Assembly 2
LT0056
Drive System Lastec//072815 2-25
Drive SystemControl Box Assembly2
2.13 Control Box Assembly
Screw, 6-32 x 3/4” SBHC SS
Clamp, Blade Switch Mount
Switch, Blade Start/Stop
Hour Meter, Digital LCD
Key, Ignition
Switch, Ignition Key
Control Box Weldmnt, AC Gas w/ Throttle
Washer, 5/16” SAE Flat
Washer, 5/16” Split Lock
Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc
Light Assy, LED Red 3/16” FI Male Quicks
Bolt, #10-24 x 1/2” Phillips PH
Washer, #10 Split Lock
Plate, Control Box Access
Nut, #6-32 Keps
Light, Red 12 Volt .187 Tabs
Socket, 12V Accessory Panel Mount
Alarm, 3372 / 3386
Nut, 3/8-16 Hex Nyloc
Washer, 3/8” Flat SAE
Washer, Throttle Friction
Handle Weldmnt, Throttle
Knob, 1 3/8” x 3/8-24
Washer Plate, Throttle Friction
Washer, Throttle Friction
Bolt, 1/4-20 x 5/8” Hex Head Grade 5
Washer, 1/4” Split Lock
Clamp, Cable
Bolt, 3/8-16 x 1 1/4” Carriage Grade 5
Nut, 5/16-18 Hex
Bolt, 5/16-18 x 1” Hex Head Grade 5
Cable Assembly, 2861 Throttle
Grommet, Cable Wiper
Boot, Vinyl Cable
REF PART # DESCRIPTION COMMENTS QTY
056250 Control Box Assembly, Gas w/Buzzer 1
1 F05004-93 6
2 043956 2
3 044588 1
4 046129 1
5 045693 2
6 046122 1
7 055481 1
8 F05011-17 3
9 F05011-13 3
10 F05006-102 3
11 050477-1 1
12 F05015-17 2
13 F05011-20 2
14 048953 1
15 F05010-59 2
16 E20482 1
17 041669 1
18 049306 1
19 F05010-10 1
20 F05011-3 1
21 046239 1
22 044715 1
23 019086 1
24 046251 1
25 046293 1
26 F05005-137 2
27 F05011-14 2
28 061974 1
1 061974 replaced 046240 Throttle Conduit Clamp (serial # 33600109 and later). Also, 063206 replaced 049856 Throttle Cable. Ser-vice Kit (063210) was created for models with serial # prior to 33600109. See bulletins PB-0256 and IS-0257 for more information.
1
29 F05007-127 1
30 F05010-17 1
31 F05006-27 1
0632061 Cable Assembly, Gas Throttle 1
32 049856 1
33 061954 1
34 061953 1
35 049747 Decal, Comm Mower Control Panel Gas 1
2-26 Lastec//072815 Drive System
Drive SystemControl Box Assembly 2
CM0003
Drive System Lastec//072815 2-27
Drive SystemPedal Assembly (Optional as of serial #26270307)2
2.14 Pedal Assembly (Optional as of serial #26270307)
Rod Weldment, Foot Control
Washer, 3/8” Flat SAE
Washer, 3/8” Push Nut
Nut, 3/8-24 Free
Pin, 3/8” x 1 5/16” Clevis
Pin, 1/8” x 3/4” Cotter
Yoke, 3/8In-24
Grip, Foot Control Black
Pedal Weldment, Foot Control
Bushing, 3/4” ID x 1” OD x 1” Oil
Washer, 20mm Bellville
Washer, 3/4” AN Yel/Cad
Ring, 3/4” External - External
Fitting, 1/4-28 Straight Grease
NOTE: To add this Foot Pedal option to your unit after serial #26270307, order Foot Pedal Kit (056241).
REF PART # DESCRIPTION COMMENTS QTY.
056241 Pedal Kit, AGC Foot Optional 1
049739 Rod Assembly, Foot Control 2
1 049738 1
2 F05011-3 1
3 F05011-110 1
4 F05010-123 1
5 P110 1
6 F05012-3 1
7 P686 1
049728 Pedal Assembly, Control 2
8 P629 1
9 049730 1
10 029842 2
11 F05011-111 1
12 F05011-77 1
13 F04254-46 1
14 P107 1
IS-0218 Instruction Sheet, 056241 Kit 1
2-28 Lastec//072815 Drive System
Drive SystemPedal Assembly (Optional as of serial #26270307) 2
LT0067
Drive System Lastec//072815 2-29
Drive SystemThrottle Assembly (Deleted after Serial # 24321106)2
2.15 Throttle Assembly (Deleted after Serial # 24321106)
NOTE: Throttle moved to control box location after Serial #24321106.
REF PART # DESCRIPTION COMMENTS QTY.
1 049856 Cable Assembly, 2861 Throttle 1
2 046240 Clamp, Throttle Conduit 1
3 019086 Knob, 1 3/8” x 3/8-24 1
4 F05015-17 Bolt, #10-24 x 1/2” PH 1
5 F05007-127 Bolt, 3/8-16 x 1 1/4” Carriage Grade 5 1
6 046251 Washer Plate, Throttle Friction 1
7 046293 Washer, Throttle Friction 1
8 046236 Handle Weldment, Throttle 1
9 046239 Washer, Throttle Friction 1
10 F05011-3 Washer, 3/8” SAE Flat 1
11 F05010-10 Nut, 3/8-16 Hex Nyl Lock 1
2-30 Lastec//072815 Drive System
Drive SystemThrottle Assembly (Deleted after Serial # 24321106) 2
049544T
Drive System Lastec//072815 2-31
Drive SystemFront Deck Lift Rod Assembly (Serial #24311106 and prior)2
2.16 Front Deck Lift Rod Assembly (Serial #24311106 and prior)
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY.
1 F05007-136 Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5 4
2 F05007-126 Bolt, 3/8-16 x 4” Hex Head Grade 5 1
3 034930 Plate Weldment, Deck Height Adjustment 1
4 F05010-10 Nut, 3/8-16 Hex Nyloc 10
5 048468 Rod End, 7/16-20 x 3/8 High Misalign 2
6 F05007-119 Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5 4
7 F05011-3 Washer, 3/8” Flat SAE 5
8 047234 Spring, .72 x 2.75 x .095 Dia SS Comp 1
9 047187 Spacer, 5/8” x 1” x 5/8” 1
10 F05010-38 Nut, 7/16-20 Jam 2
11 049787 Turnbuckle, Deck Lift Link 2
12 F05010-166 Nut, 3/8-24 LH Jam 2
13 018740 Rod End 3/8-24 Left Hand 2
14 S12284 Tube, 7/8” Dia Elec Motor Spacer 2
15 F05010-124 Nut, 3/8-16 Half Nyloc 1
16 F05004-123 Bolt, 3/8-16 x 3 1/2” Hex Head Gr5 1
17 P111 Ring, Kick-out, 1” 1
18 P212 Pin, 3/8” x 2 1/8” Clevis, Yzn 1
19 048712 Bushing, 1-1/16" Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly
2
20 048692 Strap, 1U 2
21 F05006-81 Bolt, 5/16-18 x 1 3/4” FT Hex Head Gr5 Added after serial # 1940306 1
22 F05010-17 Nut, 5/16-18 Hex Added after serial # 1940306 1
23 P04211 Knob, 5/8-18 Ball 1
24 F05007-73 Bolt, 3/8-16 x 3” Hex Head Gr5 1
25 049545 Rod Weldment, Front Deck Lift 1
2-32 Lastec//072815 Drive System
Drive SystemFront Deck Lift Rod Assembly (Serial #24311106 and prior) 2
049544
Drive System Lastec//072815 2-33
Drive SystemFront Deck Lift Rod Assembly (Serial #24331106 and later)2
2.17 Front Deck Lift Rod Assembly (Serial #24331106 and later)
Nut, 3/8-16 Hex Nyloc
Tube, 7/8” Dia. Elec Motor Spacer
Rod End 3/8-24 Left Hand
Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5
Nut, 3/8-24 LH Jam
Turnbuckle, Deck Lift Link
Nut, 7/16-20 Jam
Rod End, 7/16-20 x 3/8” High Misalign
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY.
049544 Rod Assembly, Front Deck Lift 1
1 F05007-136 Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5 4
2 F05007-126 Bolt, 3/8-16 x 4” Hex Head Grade 5 1
3 055464 Plate Weldment, Deck Height Adjust 1
4 F05010-10 Nut, 3/8-16 Hex Nyloc 6
5 P04211 Knob, 5/8-18 Ball 1
6 048187 Handle Weldment, Deck Raise 1
7 F05007-73 Bolt, 3/8-16 x 3” Hex Head Grade 5 1
8 047234 Spring, .72” x 2.75” x .095” Dia. SS Comp 1
9 F05011-3 Washer, 3/8” Flat SAE 5
10 049545 Rod Weldment, Front Deck Lift 1
11 F05004-123 Bolt, 3/8-16 x 3 1/2” Hex Head Grade 5 1
12 F05010-124 Nut, 3/8-16 Half Nyloc 1
13 048712 Bushing, 1 1/16" Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly
2
14 048692 Strap, 1U 2
15 P212 Pin, 3/8” x 2 1/8” Clevis 1
16 P111 Ring, 1” Kick-Out 1
049788 Rod Assembly, Deck Lift Link 2
17 F05010-10 2
18 S12284 1
19 018740 1
20 F05007-119 2
21 F05010-166 1
22 049787 1
23 F05010-38 1
24 048468 1
2-34 Lastec//072815 Drive System
Drive SystemFront Deck Lift Rod Assembly (Serial #24331106 and later) 2
LT0057
Drive System Lastec//072815 2-35
Drive SystemEmergency Brake Assembly2
2.18 Emergency Brake Assembly
REF PART # DESCRIPTION COMMENTS QTY.
049550 Handle Assembly, E-Brake 1
1 P04211 Knob, 5/8-18 Ball 1
2 029360 Handle Weldment, E-Brake 1
3 F05010-10 Nut, 3/8-16 Hex Nyloc 2
4 P786 Bushing, 3/4” ID x 1” OD x 5/8” Lng Flanged 1
5 F05012-115 Pin, 3/4” Clevis Retaining 1
6 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 2
7 049537 Arm, E-Brake Link 1
8 029214 Spacer, 1.00” OD x .41” ID x 1/4” Thk Nylon-Blk 2
9 F05010-8 Nut, 1/2-13 Nyl Hex Lock 1
10 F05011-2 Washer, 1/2” SAE Flat 1
11 F05011-97 Washer, 1/2” Plain Belleville 6
12 029354 Block, E-Brake Pivot 1
13 029397 Rod Weldment, Brake Actuator 1
14 026407 Plate Weldment, E-Brake Lock 1
15 F05012-11 Pin, 3/16” x 1” Roll 1
16 026412 Rod Weldment, E-Brake Tensioner 1
17 F05012-1 Pin, 1/8” x 1” Cotter 1
18 P110 Pin, 3/8” x 1 5/16” Clevis 1
19 026409 Pulley, E-Brake 1
20 026416 Cable E-Brake 1
2-36 Lastec//072815 Drive System
Drive SystemEmergency Brake Assembly 2
LT0055
Drive System Lastec//072815 2-37
Drive SystemRear Deck Lift Rod Assembly2
2.19 Rear Deck Lift Rod Assembly
Rod End 3/8-24 Left Hand
Nut, 3/8-24 LH Jam
Turnbuckle, Deck Lift
Nut, 3/8-24 UNF Hex Jam
Rod End, 3/8-24 Right Hand
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY.
049541 Rod Assembly, Rear Deck Lift 1
1 F05007-136 Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5 4
2 048712 Bushing, 1 1/16" Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly.
2
3 048692 Strap, 1U 2
4 F05011-3 Washer, 3/8” Flat SAE 4
5 F05010-10 Nut, 3/8-16 Hex Nyloc 7
6 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 2
026448 Turnbuckle Assembly, Deck Lift 1
7 018740 1
8 F05010-166 1
9 026447 1
10 F05010-22 1
11 018739 1
12 026446 Rod Wldmnt, Spring Tensioner 1
13 F05011-101 Washer, 1/2” SAE Flat Gr5-8 (Thru Hard) 1
14 055442 Washer, 1/2” Delrin 1
15 026443 Block, Spring Tensioner 1
16 026371 Spring, 1 3/8" x 15.8” x .187” Extension 2
17 046534 Mount, Spring 1
18 F05007-109 Bolt, 3/8-16 x 4 3/4” Hex H ead Grade 5 1
19 049542 Rod Wldmnt, Rear Deck Lift 1
20 P110 Pin, 3/8” x 1 5/16” Clevis Serial # 1940306 and later 2
F05012-8 Pin, 3/8” x 1 3/32” Clevis Serial # 1520306 and prior 2
21 P111 Ring, 1” Kick-Out 2
2-38 Lastec//072815 Drive System
Drive SystemRear Deck Lift Rod Assembly 2
LT0058
Drive System Lastec//072815 2-39
Drive SystemFramework2
2.20 Framework
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY.
1 F05010-58 Nut, 5/16-18 Nylon Lock Hex 1
2 F05011-17 Washer, 5/16” SAE Flat 1
3 024155 Clamp, 1/4” Wire 13/32 Mtg Hole 1
4 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 1
5 F05007-125 Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5 2
6 047234 Spring, .72” x 2.75” x .095” Dia SS Comp 2
7 F05010-10 Nut, 3/8-16 Hex Nyloc 2
8 F05010-14 Nut, #10-24 Keps 4
9 043459 Switch, DPST NO 5A Plunger 3
10 F05004-126 Screw, 10-24 x 3/4” Phillips PH Machine 4
11 046559 Switch, DPST N/O N/C 1
12 F05004-1 Screw, 10-24 x 1/2” Sl Hex Machine 4
13 F05011-20 Washer, #10 Split Lock 4
14 044021 Cover, Handle Lockout Switch Left 1
15 044020 Cover, Handle Lockout Switch Right
16 049870 Bushing, Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly
6
17 P195 Cap, Hub 1
18 049984 Sure Grip, Foot Pan 1
19 055841 Sure Grip, 1 1/2” Bar 1
20 P107 Fitting, 1/4-28 Straight Grease 1
21 P611 Holder, Jumbo Cup Black 2
22 046477 Wheel Yoke Assembly, 13” Comm See Section 2.10 1
2-40 Lastec//072815 Drive System
Drive SystemFramework 2
LT0068
Drive System Lastec//072815 2-41
Drive SystemPull Bar Assembly2
2.21 Pull Bar Assembly
Bar Weldment, Pull
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
Nut, 5/8-11 FlexLoc
Washer, 5/8” Standard Flat
REF PART # DESCRIPTION COMMENTS QTY.
049488 Bar Assembly, Pull 1
1 049484 1
2 F05009-35 4
3 F0510-185 4
4 F05011-40 2
2-42 Lastec//072815 Drive System
Drive SystemPull Bar Assembly 2
3373_018
Drive System Lastec//072815 2-43
Drive SystemRoller Assembly Upgrade Kit (Optional)2
2.22 Roller Assembly Upgrade Kit (Optional)
NOTE: Apply anti-seize to pivot bolts prior to assembly.
NOTE: Lubricate grease fittings using water-proof grease until discharge is visible from seals and bushings.
REF PART # DESCRIPTION COMMENTS QTY.
063377 Upgrade Kit, 61-73 AGC Roller Optional 1
1 P04211 Knob, 5/8-18 Ball 1
2 048930 Roller Lift Pivot Wldmnt 1
3 F05009-111 Bolt, 5/8” x 1/2” Shoulder 2
4 F05011-107 Washer, .625 ID x 1.312 OD x .050 Thick Nylon 4
5 F05011-9 Washer, 1/2” Split Lock 2
6 F05008-37 Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 2
7 F05010-8 Nut, 1/2-13 Hex Nylon Lock 11
8 063378 Pivot Collar Mount Weldment 61-73AGC 1
9 029109 Spacer, 3/16” Thk Deck Height 1
10 F05008-143 Bolt, 1/2-13 x 3 3/4” Hex Head Grade 5 3
11 063382 Plate, Clamp Pivot Collar Mount 2
12 F04254-46 Ring, 3/4” External Retaining 1
13 F05011-77 Washer, 3/4” AN Yel/Cad 1
14 029842 Bushing, 3/4” ID x 1” OD x 1” Oil 2
15 063384 Spacer, Lift Link Arm 61-73 AGC 2
16 063383 Arm, Roller Lift Link 61-73 AGC 1
17 048941 Strip, Roller Wiper 1
18 F05011-17 Washer, 5/16” SAE Flat 3
19 F05011-13 Washer, 5/16” Split Lock 3
20 F05006-27 Bolt, 5/16-18 x 1” Hex Head Grade 5 3
21 F05007-118 Bolt, 3/8-16 x 3/4” Hex Head Grade 5 4
22 F05011-4 Washer, 3/8” Split Lock 4
23 F05011-3 Washer, 3/8” SAE Flat 4
24 023541 Bearing, 1” Flanged Mount 2
25 048908 Roller Weldment, 3373 Stripping 1
26 048910 Frame Weldment, Upgrade Kit 1
27 F05008-159 Bolt, 1/2-13 x 6 1/2” Hex Head Grade 5 8
28 F05009-37 Bolt, 5/8-11 x 3” Hex Head Grade 5 2
29 P107 Fitting, 1/4-28 Straight Grease 3
30 063870 Tube, Roller Mount Spacer 2
31 019094 Plate, Drive Motor Mount 2
32 063869 Plate, Roller Mount 1
33 F05010-185 Nut, 5/8-11 Flexlock 2
IS-0277 Instruction Sheet, 61-73 Roller Assembly 1
2-44 Lastec//072815 Drive System
Drive SystemRoller Assembly Upgrade Kit (Optional) 2
290006
Drive System Lastec//072815 2-45
Drive SystemStriping Kit (Optional)2
2.23 Striping Kit (Optional)
NOTE: This 042947 Striping Kit may be purchased through your Lastec Dealer.
REF PART # DESCRIPTION COMMENTS QTY.
042947 Striping Kit, Commercial Mower 1
1 042951 Bracket Weldment, Left Striping Kit 1
2 042950 Bracket Weldment, Right Striping Kit 1
3 042949 Plate Weldment, Hanger Strap 1
4 042943 Plate, Mount Washer 2
5 F05011-9 Washer, 1/2” Split Lock 4
6 F05008-37 Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 4
7 042945 Pad, Rubber Striping 1
8 042942 Strap, Rubber Pad Mounting 1
9 F05011-4 Washer, 3/8” Split Lock 6
10 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 6
IS-0192 Instruction Sheet, 61” Deck Striping Kit 1
2-46 Lastec//072815 Drive System
Drive SystemStriping Kit (Optional) 2
LT0045
Drive System Lastec//072815 2-47
Lastec//072815 3-1
3
SECTION 3 HYDRAULIC SYSTEM
Hydraulic SystemHydraulic Layout Diagram (Serial #46570113 and later)3
3.1 Hydraulic Layout Diagram (Serial #46570113 and later)
Hydraulic Mainentance Kits
REF PART # DESCRIPTION COMMENTS QTY.
1 072587 Hose Assembly, 1/2” HP x 30” ORFS 8 ST 4
2 072599 Hose Assembly, 3/8” LP x 16.5” ORFS 6 45 2
3 072597 Hose Assembly, 3/8” LP x 6” ORFS 6 90 2
4 072598 Hose Assembly, 3/8” LPx12” ORFS 6 ST 2
REF PART # DESCRIPTION COMMENTS QTY.
049928 Kit, Hydro Oil Repl 5 Gal 3372 1
028535 Oil, Shell TTF-SB 5 gal
P620 Filter Element, Spin On, BE-25-25 Zinga 4
049929 Kit, Hydro Oil Repl 2 1/2 Gal 3372 1
028535 Oil, Shell TTF-SB 2.5 gal
P620 Filter Element, Spin On, BE-25-25 Zinga 2
040642 Oil,TTF-SB 32 oz. Bottle Hydro 1
028535 Oil, Shell TTF-SB 1 qt.
040630 Decal, Hydraulic TTF-SB Oil 1
040635 Black Cap, for 32 oz. Bottle Oil Container 1
040636 Bottle, 32 oz. Container for Oil 1
040637 Spout Cap/ W Red Seal for 32 oz. Container 1
047600 Kit, Hydro-Gear Flow Test 1
048400 Seal Kit, Hydro-Gear BDP 10-12 Seal Kit for Pumps 1
3-2 Lastec//072815 Hydraulic System
Hydraulic SystemHydraulic Layout Diagram (Serial #46570113 and later) 3
290013-2
TANK
FILTERS
PUMP
PUMP
MOTOR MOTOR
Hydraulic System Lastec//072815 3-3
Hydraulic SystemHydraulic Layout Diagram (Prior to Serial #46570113)3
3.2 Hydraulic Layout Diagram (Prior to Serial #46570113)
Hydraulic Mainentance Kits
REF PART # DESCRIPTION COMMENTS QTY.
1 041180 Hose Assembly, 26” OAL x 1/2” Hyd Serial #1700206 and later 4
045990 Hose Assembly, 1/2 x 15 1/2” JIC Serial #1690206 and prior 4
2 045970 Hose, 3/8” Hyd x 3 1/4” Low Pressure 2
3 015485 Fitting, 3/8” Barb Tee 1
4 049857 Hose, 3/8” Hyd x 12” Low Pressure 4
5 045972 Hose, 3/8” Hyd x 9 1/2” Low Pressure 1
061807 Hose Clamp, Dixon Worm Gear HSS6 Not Shown 12
REF PART # DESCRIPTION COMMENTS QTY.
049928 Kit, Hydro Oil Repl 5 Gal 3372 1
028535 Oil, Shell TTF-SB 5 gal
P620 Filter Element, Spin On, BE-25-25 Zinga 4
049929 Kit, Hydro Oil Repl 2 1/2 Gal 3372 1
028535 Oil, Shell TTF-SB 2.5 gal
P620 Filter Element, Spin On, BE-25-25 Zinga 2
040642 Oil,TTF-SB 32 oz. Bottle Hydro 1
028535 Oil, Shell TTF-SB 1 qt.
040630 Decal, Hydraulic TTF-SB Oil 1
040635 Black Cap, for 32 oz. Bottle Oil Container 1
040636 Bottle, 32 oz. Container for Oil 1
040637 Spout Cap/ W Red Seal for 32 oz. Container 1
047600 Kit, Hydro-Gear Flow Test 1
048400 Seal Kit, Hydro-Gear BDP 10-12 Seal Kit for Pumps 1
3-4 Lastec//072815 Hydraulic System
Hydraulic SystemHydraulic Layout Diagram (Prior to Serial #46570113) 3
F F
P P
Tank
Motor Motor
LT0076
Hydraulic System Lastec//072815 3-5
Hydraulic SystemHydraulic Pump Assemblies3
3.3 Hydraulic Pump Assemblies
Bushing, 15mm Split Taper
Washer, 1/4” Split Lock
Bolt, 1/4-20 x 1” Hex Head Grade 5
Sheave, BK60 QT
Key, 5mm x 5mm x 25mm
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
Washer, 3/8” Flat SAE
Nut, 3/8-16 Hex Nyloc
Fitting, 6 ORFS - 6 STOR 90
Bolt, 5/16-18 x 1 3/4” Hex Head
Spacer, Hydro Actuator
Nut, 5/16-18 Nylok Hex
Pump, 12cc Hydrostatic
Pump, 12cc Hydrostatic
Actuator Kit, RTN Std for Model 2861
Fitting, 8 ORFS - 8 STOR LL 90
Turnbuckle Assembly, Hydro
Rod End, 5/16-24 Male LH
Nut, 5/16-24 Jam LH
Rod, Hydro Control Link
Nut, 3/8-24 Free
Rod End, 3/8-24 Right Hand
NOTE: Left and right pump assemblies are mirror images of each other. (Right Pump Assembly shown below.)
REF PART # DESCRIPTION COMMENTS QTY.
049837 1
1 072560 replaced (2) 026393 Fitting, #8 SAE / #8 JIC 90 X-L Elbow, (2) 072585 replaced (1) 026394 Fitting, #6 SAE x 3/8” Hose Str and (1) P12722 Fitting, #6 90 Deg SAE #6 Hose Barb Hyd; 072587 replaced 041180 Hose Assembly, 26” OAL x 1/2” Hyd; removed 045970 Hose, 3/8” Hyd x 3-1/4 Low Pressure and 061807 Hose Clamp, Dixon Worm Gear HSS6 (Serial #46570113 and later).
Pump Assembly, 12cc Right Hydro Right Side 1
0498361 Pump Assembly, 12cc Left Hydro Left Side 1
1 019359 1
2 F05011-14 2
3 F05005-101 Tighten bolts to 84 in-lbs 2
4 018773 1
5 048532 1
6 F05007-78 1
7 F05011-3 2
8 F05010-10 2
9 072585 2
10 F05009-70 1
11 026399 1
12 F05010-58 1
13 048284 2
2 Pumps include the Actuator Kit (046820) already installed.
Right Pump 1
048285 2 Left Pump 1
046820 Parts not sold separately 1
14 072560 2
15 0725871 Hose Assembly, 1/2HP x 30In ORFS 8 ST 2
16 026470 Belt, BX54 1
049838 2
17 014815 1
18 F05010-119 1
19 049839 1
20 F05010-123 1
21 018739 1
3-6 Lastec//072815 Hydraulic System
Hydraulic SystemHydraulic Pump Assemblies 3
LT0139-1
Hydraulic System Lastec//072815 3-7
Hydraulic SystemHydraulic Motor, Right3
3.4 Hydraulic Motor, Right
Drum, 152.4mm w/Studs
Brake, 152.4 x 25 Cam
Key, 5/16” x 1” Woodruff
Hex Nut, 1-20 Slotted
REF PART # DESCRIPTION COMMENTS QTY.
049965 Wheel/Motor Assembly, 2861 Right Rear 1
1 P04646 Nut, 1/2-20 Lug Torque to 144 ft.-lbs. 5
2 F05011-115 Washer, 1” ID .03 SS Shim As Req’d
3 F05011-116 Washer, 1” ID .06 SS Shim As Req’d
4 043320 Brake Assembly, 3377TZ Rear Drum See Section 3.6 for parts 1
043320-1 1
043320-2 1
5 F05010-121 Nut, 5/16-18 Nylon Locking Jam 1
6 F05011-16 Washer, 5/16” Standard Flat 1
7 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc 1
8 F05006-117 Bolt, 5/16-18 x 3/4” SHC SS 4
9 F05011-13 Washer, 5/16” Split Lock 4
10 F05008-28 Bolt, 1/2-13 x 5 1/2” Hex Head Grade 5 4
11 F05010-8 Nut, 1/2-13 Nyl Hex Lock 4
12 F05011-101 Washer, 1/2” SAE Flat Grade 5-8 (Thru Hard) 4
13 071864 1
1 071864 replaced (2) 072561 Fitting, 8 ORFS - 10 STOR 45 (Serial #47960513 and later). 072561 replaced (2) 016807 Fitting, #10 SAE-1/2” JIC 45 Elbow (Serial #46570113 to #47950513).
Fitting, 8 ORFS - 10 STOR 90 2
14 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 1
15 055177 Plate, E-Brake Pulley Right Serial # 2760706 and later 1
027056 Plate, E-Brake Pulley Right Serial # 2750706 and prior 1
16 F05011-3 Washer, 3/8” Flat SAE 2
17 026409 Pulley, E-Brake 1
18 055151 Plate, E-Brake Cable Retaining 1
19 F05010-124 Nut, 3/8-16 Half Nyloc 1
20 F05012-49 Pin, 1/8” x 1 1/2” Cotter 1
21 046659 Motor, Right Hydro-Gear Drive 1
22 046800 1
23 026417 1
026439 Tire Assembly, 24” x 12-12 Turf Master Not Shown 1
041098-1 Tire, 24” x 12-12 (Tire Only) 1
026440 Rim, 12” x 8 1/2” 8 Spoke 4 1/2” BC 1
3-8 Lastec//072815 Hydraulic System
Hydraulic SystemHydraulic Motor, Right 3
LT0069C
Hydraulic System Lastec//072815 3-9
Hydraulic SystemHydraulic Motor, Left3
3.5 Hydraulic Motor, Left
Drum, 152.4mm w/Studs
Brake, 152.4 x 25 Cam
Key, 5/16” x 1” Woodruff
Hex Nut, 1-20 Slotted
REF PART # DESCRIPTION COMMENTS QTY.
049966 Wheel/Motor Assembly, 2861 Left Rear 1
1 P04646 Nut, 1/2-20 Lug Torque to 144 ft.-lbs. 5
2 F05011-115 Washer, 1” ID .03 SS Shim As Req’d
3 F05011-116 Washer, 1” ID .06 SS Shim As Req’d
4 043320 Brake Assembly, 3377TZ Rear Drum See Section 3.6 for parts 1
043320-1 1
043320-2 1
5 F05010-121 Nut, 5/16-18 Nylon Locking Jam 1
6 F05011-16 Washer, 5/16” Standard Flat 1
7 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc 1
8 F05006-117 Bolt, 5/16-18 x 3/4” SHC SS 4
9 F05011-13 Washer, 5/16” Split Lock 4
10 F05008-28 Bolt, 1/2-13 x 5 1/2” Hex Head Grade 5 4
11 F05010-8 Nut, 1/2-13 Nyl Hex Lock 4
12 F05011-101 Washer, 1/2” SAE Flat Grade 5-8 (Thru Hard) 4
13 071864 1
1 071864 replaced (2) 072561 Fitting, 8 ORFS - 10 STOR 45 (Serial #47960513 and later). 072561 replaced (2) 016807 Fitting, #10 SAE-1/2” JIC 45 Elbow (Serial #46570113 to #47950513).
Fitting, 8 ORFS - 10 STOR 90 2
14 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 3
15 F05007-124 Bolt, 3/8-16 x 2” Hex Head Grade 5 1
16 055178 Plate, E-brake Pulley Left Serial # 2760706 and later 1
027057 Plate, E-brake Pulley Left Serial # 2750706 and prior 1
17 F05011-3 Washer, 3/8” Flat SAE 6
18 026409 Pulley, E-Brake 3
19 055151 Plate, E-Brake Cable Retaining 3
20 F05010-124 Nut, 3/8-16 Half Nyloc 3
21 F05012-49 Pin, 1/8” x 1 1/2” Cotter 1
22 046661 Motor, Hydro Gear 1
23 046800 1
24 026417 1
026439 Tire Assembly, 24” x 12-12 Turf Master Not Shown 1
041098-1 Tire, 24” x 12-12 (Tire Only) 1
026440 Rim, 12” x 8 1/2” 8 Spoke 4 1/2” BC 1
3-10 Lastec//072815 Hydraulic System
Hydraulic SystemHydraulic Motor, Left 3
LT0070C
Hydraulic System Lastec//072815 3-11
Hydraulic SystemBrake Assembly3
3.6 Brake Assembly
Drum, 152.4mm w/Studs
Stud, 1/2-20 x 1-1/4 Press In
Brake, 152.4 x 25 Cam
Shoe, 152.4 x 25 Brake
Spring, 152.4 x 25 Brake Return
Cam, 152.4 x 25 Brake
Backing Plate, 152.4 x 25 Brake
Arm, 152.4 x 25 Brake Actuator
Clip, 152.4 x 25 Retainer
REF PART # DESCRIPTION COMMENTS QTY.
043320 Brake Assembly, Rear Drum Includes Items 1 to 8 1
1 043320-1 Includes Item 2 1
2 043320-4 5
043320-2 Includes Items 3 to 8 1
3 043320-9 2
4 043320-10 2
5 043320-8 1
6 043320-7 1
7 043320-5 1
8 043320-6 1
3-12 Lastec//072815 Hydraulic System
Hydraulic SystemBrake Assembly 3
3300_045
Hydraulic System Lastec//072815 3-13
Hydraulic SystemHydraulic Tank Assembly (Serial #46570113 and later)3
3.7 Hydraulic Tank Assembly (Serial #46570113 and later)
Fitting, 6 ORFS - 6 PushLok 45
Hose, 3/8” Hyd x 14” Low Press.
Fitting, 6 ORFS - 6 PushLok ST
Fitting, 6 ORFS - 6 PushLok ST
Hose, 3/8” Hyd x 4” Low Press.
Fitting, 6 ORFS - 6 PushLok 90
Fitting, 6 ORFS - 6 PushLok ST
Hose, 3/8” Hyd x 10” Low Press.
REF PART # DESCRIPTION COMMENTS QTY.
072591 Tank Assembly, 29AGC Hyd 1
1 P12708 Fitting, 3/8” NPT-3/8” Barb Elbow 2
2 072505 Hose Clamp, 3/16” Spring 2
3 047883 Tube, Vinyl Sight Gage 1
4 072584 Fitting, 6 ORFS - 6 MPT 45 2
5 072556 Fitting, 6 ORFS - 6 MPT 90 6
6 049891 Hose, 3/8” Low Pressure 28” 1
7 P12724 Fitting, 3/8” NPT-3/8” Barb 3
8 043251 Bushing, Hex, 3/4” x 3/8” 1
9 072582 Tank Weldment, 28AGC Hyd 1
10 F05010-124 Nut, 3/8-16 Half Nylock 4
11 F05011-3 Washer, 3/8” Flat SAE 4
12 F05007-87 Bolt, 3/8-16 x 1” Hex Head Grade 5 4
13 F05005-79 Bolt, 1/4-20 x 1/2” HHC 4
14 F05011-14 Washer, 1/4” Split Lock 4
15 P619 Filter Head, 3/8” NPT 2
16 P620 Filter Element, Spin On, BE-25-25 Zinga 2
17 027066 Hose, 2561 Oil Drain Includes (2) Fittings (P12724) 1
18 028593 Clamp. 3/4” EMY Coated 1
19 P04332 Cap, 3/8” Pipe Galvanized 1
072599 Hose Assembly, 3/8” LPx16.5” ORFS 6 45 2
20 072600 1
21 072596 1
22 072541 1
072597 Hose Assembly, 3/8” LP x 6” ORFS 6 90 2
23 072541 1
24 072594 1
25 072539 1
072598 Hose Assembly, 3/8” LP x 12” ORFS 6 ST 2
26 072541 2
27 072595 1
28 041083 Valve, Two Tank Diverter 1
3-14 Lastec//072815 Hydraulic System
Hydraulic SystemHydraulic Tank Assembly (Serial #46570113 and later) 3
290012
Hydraulic System Lastec//072815 3-15
Hydraulic SystemHydraulic Tank Assembly (Priot to Serial #46570113)3
3.8 Hydraulic Tank Assembly (Priot to Serial #46570113)
REF PART # DESCRIPTION COMMENTS QTY.
055897 Tank Assembly, 29HP Hyd 1
1 P12708 Fitting, 3/8” NPT-3/8” Barb Elbow 1 added after Serial # 3011006 7
2 P649 Hose Clamp, 7/32”-5/8” 2
3 047883 Tube, Vinyl Sight Gage 1
4 048988 Fitting, 3/8” NPT - 3/8” Barb 45 Deg 2
5 061807 Hose Clamp, Dixon Worm Gear HSS6 Serial # 33401208 and later 9
P12739 Hose Clamp, 11/16” Worm Serial # 33391208 and prior 9
6 049857 Hose, 3/8” Hyd x 12” Low Press. 4
7 049891 Hose, 3/8” Low Pressure 28” 1
8 P12724 Fitting, 3/8” NPT-3/8” Barb Includes (2) Fittings (027066) 3
9 043251 Bushing, Hex, 3/4” x 3/8” 1
10 049596 Tank Weldment, 2861AGC Hyd 1
11 028492 Plug, 3/8” NPT Hex Brass 1 removed after Serial # 3011006 1
12 F05010-124 Nut, 3/8-16 Half Nylock 4
13 F05011-3 Washer, 3/8” Flat SAE 4
14 F05007-87 Bolt, 3/8-16 x 1” Hex Head Grade 5 4
15 F05005-79 Bolt, 1/4-20 x 1/2” HHC 4
16 F05011-14 Washer, 1/4” Split Lock 4
17 P619 Filter Head, 3/8” NPT 2
18 P620 Filter Element, Spin On, BE-25-25 Zinga 2
19 028493 Fitting, 3/8” NPT F-M-F Tee Serial # 3011006 and later 1
028072 Fitting, 3/8” NPT Street Tee Serial # 3001006 and prior 1
20 045972 Hose, 3/8” Hyd x 9 5/8” Low Press. 1
21 027066 Hose, 2561 Oil Drain Added after serial # 3011006 1
22 028593 Clamp. 3/4” EMY Coated Added after serial # 3011006 1
23 P04332 Cap, 3/8” Pipe Galvanized Added after serial # 3011006 1
24 041083 Valve, Two Tank Diverter 1
3-16 Lastec//072815 Hydraulic System
Hydraulic SystemHydraulic Tank Assembly (Priot to Serial #46570113) 3
290005
Hydraulic System Lastec//072815 3-17
Hydraulic SystemHydraulic Drive Idler Assembly3
3.9 Hydraulic Drive Idler Assembly
REF PART # DESCRIPTION COMMENTS QTY.
049570 Idler Assembly, Hydro Drive 1
1 F05010-8 Nut, 1/2-13 Nylon Hex Lock 2
2 F05011-2 Washer, 1/2” SAE Flat Added after serial # 2200406 2
3 049571 Rod, Polyurethane Spring 4
4 049569 Arm Weldment, Hydro Tensioner 1
5 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 1
6 046144 Pulley, 5” OD Idler 1
3-18 Lastec//072815 Hydraulic System
Hydraulic SystemHydraulic Drive Idler Assembly 3
LT0078
Hydraulic System Lastec//072815 3-19
Lastec//072815 4-1
4
SECTION 4 ENGINE & ELECTRICAL
Engine & ElectricalFuel Tank Assembly (Serial #46570113 and later)4
4.1 Fuel Tank Assembly (Serial #46570113 and later)
Gauge, Fuel Indicator Sealed
Grommet, Fuel Gauge Sealed
Fitting,1/4” Barb 90 Tank w/3" Long Tube
Grommet, Fuel Tank Fitting
Tube, Fuel Pick Up
Vent, Remote w/Valve
Grommet, Remote Vent
Tube, 3.5" Vapor Neck
REF PART # DESCRIPTION COMMENTS QTY.
067359 Tank Assembly, Gasoline Dual Fittings 1
1 067363 Cap, Gas Fuel Tank Ratchet 350 1
2 F05004-18 Screw, 10-24 x 5/8” Unsl Indent HH Machine 2
3 F05011-20 Washer, #10 Split Lock 2
4 085614 Grommet, Rubber 2 1/2” Dia 3
5 043441 Washer, Fuel Tank Retaining 1
6 019696 Cap, Hyd Tank (P631) 3
7 043442 Washer, Fuel Tank Double 1
072858 1
1 Replaced 067361 Fuel Dual Fitting Tank Assembly (9/14).
Tank Assembly, 7 Gallon Gas Dual Fitting Includes Fuel Tank 1
8 072735 1
9 072736 1
10 049809 1
11 028818 2
12 055446 1
13 064653 1
14 064654 1
15 067364 1
16 045897 Plate, Decal Fuel 1
17 F05004-285 Screw, 10-24 x 5/8” SBHC SS 2
18 F05010-160 Nut, 10-24 Hex Nylock 2
4-2 Lastec//072815 Engine & Electrical
Engine & ElectricalFuel Tank Assembly (Serial #46570113 and later) 4
LT0138B
Engine & Electrical Lastec//072815 4-3
Engine & ElectricalFuel Tank Assembly (Serial #25620207 to #46560113)4
4.2 Fuel Tank Assembly (Serial #25620207 to #46560113)
Gage, Fuel Indicator
Grommet, Fuel gage
Fitting,1/4” Barb 90 Tank w/ 3" Long Tube
Grommet, Fuel Tank Fitting
Tube, Fuel Pick Up
REF PART # DESCRIPTION COMMENTS QTY.
045973 Tank Assembly, Gasoline Dual Fittings 1
1 063252 Cap, Gas Fuel Tank Vented 1
2 F05004-18 Screw, 10-24 x 5/8” Unsl Indent HH Machine 2
3 F05011-20 Washer, #10 Split Lock 2
4 085614 Grommet, Rubber 2 1/2” Dia 3
5 043441 Washer, Fuel Tank Retaining 1
6 019696 Cap, Hyd Tank (P631) 3
7 043442 Washer, Fuel Tank Double 1
055438 Tank Assembly, Fuel Dual Fitting Includes Fuel Tank 1
8 049908 1
9 049909 1
10 049809 1
1 Replaced 1/4” Barb 90 Tank Fitting (028820) and 1/4” x 2" Long Tygon Tubing (046532) (Serial #39030111 and later).
1
11 028818 2
12 055446 1
13 045897 Plate, Decal Fuel 1
14 P485 Decal, Fuel Equipment 1
4-4 Lastec//072815 Engine & Electrical
Engine & ElectricalFuel Tank Assembly (Serial #25620207 to #46560113) 4
LT0074
Engine & Electrical Lastec//072815 4-5
Engine & ElectricalFuel System4
4.3 Fuel System
Hose Clamp, 1/2” Spring
Hose, Fuel 1/2” x 2-1/4”
Fuel Pump Module
Strap, Fuel Pump Mount
Fuel Pump
Bracket, Fuel Pump Bottom
Spacer, Fuel Pump Mount
Grommet, Fuel Pump Mount
Screw, 10-24 x 1 1/4” Unsl Ind HH Machine
Washer, #10 SAE Flat
Nut, 10-24 Hex Nylock
Hose, Fuel 5/16” x 15” Lng
Hose, Fuel 5/16” x 42” Lng
Hose Clamp, 5/16” Spring
REF PART # DESCRIPTION COMMENTS QTY.
1 072506 1
1 (21) 072506 replaced (21) P649 Hose Clamp, 7/32”-5/8”, (2) 072588 replaced (2) 061807 Clamp, 7/16-25/32 Worm and (4) 072507 replaced (4) P649 Hose Clamp, 7/32”-5/8” (Serial #46570113 and later).
Hose Clamp, 1/4” Spring 21
2 045588 Hose, 1/4” x 16” Fuel 2
3 048998 Hose, Fuel 1/4” x 48” 1
4 019298 Hose, Fuel, 1/4” x 8”, 325E98 1
5 046762 Filter, Fuel 1/4” 1
6 046772 Adapter, Fuel Hose Reducer 1
0467701 Fuel Pump Assembly, 29Hp 1
7 072588 2
8 046771 1
046765 1
9 046769 Not Sold Separately 1
10 046761 Not Sold Separately 1
11 046764 Not Sold Separately 1
12 046768 Not Sold Separately 2
13 046767 Not Sold Separately 2
14 F05004-19 2
15 F05011-18 2
16 F05010-160 2
17 055924 1
18 055896 1
19 072507 4
20 040388 Hose, Fuel 1/4” x 32" 2
21 041083 Valve, Two Tank Diverter 1
22 067370 Carbon Canister, 9 Gal Added (Serial #46570113 and later) 2
23 067973 Hose Clamp, 3/16” Spring 2
24 F05005-68 Bolt, 1/4-20 x 1 3/4” Hex Head Grade 5 2
25 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 2
26 F05010-220 Nut, 1/4-20 Flanged Hex Nylock 2
27 F05010-221 Nut, 5/16-18 Flanged Hex Nylock 1
28 F05011-13 Washer, 5/16 Split Lock 1
29 045320 Hose, Fuel 1/4” x 36” 1
30 045328 Hose, Fuel 1/4” x 20” 2
31 045585 Hose, Fuel 1/4” x 14” 1
32 064658 Fitting, 1/4” Tee Barb 1
4-6 Lastec//072815 Engine & Electrical
Engine & ElectricalFuel System 4
Return Line
To Injectors
To Engine CARB Port
290013-1
Fuel pump attachedto underside
of battery tray
Engine & Electrical Lastec//072815 4-7
Engine & ElectricalEngine Guard Assembly4
4.4 Engine Guard Assembly
REF PART # DESCRIPTION COMMENTS QTY.
044833 Guard Assembly, AC Series 1
1 F05010-160 Nut, 10-24 Hex Nylock 2
2 P06104 Foot, Rubber 2
3 F05004-35 Screw, 10-24 x 1/2” SBHC 2
4 044835 Guard Weldment, AC Series 1
5 F05010-10 Nut, 3/8-16 Hex Nyloc 3
6 060169 Knob, 3/8” Bore Oval/Tapered Plastic Serial # 28190707 and later 1
S08291-W Handle, Power/Feed & Up/Down Serial # 28180707 and prior;No longer available: 0rder 060169
1
7 F05007-214 Screw, 3/8-16 x 2” SHC Serial # 3021006 and later 1
F05007-58 Screw, 3/8-16 x 2” BO SHC Serial # 3020906 and prior 1
8 F05007-129 Bolt, 3/8-16 x 1 3/4” FT Grade 5 2
9 027006 Spring, 1-1/8" x 7-1/2" x .091 Extension 1
4-8 Lastec//072815 Engine & Electrical
Engine & ElectricalEngine Guard Assembly 4
LT0072
Engine & Electrical Lastec//072815 4-9
Engine & ElectricalEngine Assembly4
4.5 Engine Assembly
Clutch, 5.75 Dia x 1-1/8 Bore 12V
Capture Weldment, Clutch Stop
Nut, 5/16-18 Nylok Hex
Washer, 5/16 SAE Flat
Stop Weldment, Clutch
Washer, 5/16 Star ET
Bolt, 5/16-18 x “1 Hex Head Grade 5
Hose, Clutch Stop Bushing
Washer, 3/8” Flat SAE
Nut, 3/8-16 Half Nyloc
REF PART # DESCRIPTION COMMENTS QTY.
046125 Engine Assembly, 29HP 1
1 047662 Spark Plug, Kawasaki 2
2 046126 Engine, Kawasaki 29HP 1
3 049847 Belt, B-134 Custom 61" Deck Only 1
055445 Belt, B-130 Custom 73" Deck Only 1
4 047663 Oil Filter, Kawasaki 1
5 046783 Air Intake Assembly See Section 4.9 1
6 048205 1 Radiator, Kawasaki 2961 1
7 046719 Radiator Cowling Assembly See Section 4.6 1
8 F05004-48 Bolt, M10-1.5 x 25mm Hex Head FT 8.8 Serial # 26670407 and later 4
F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 Serial # 26660407 and prior 4
9 F05011-88 Washer, 10mm Split Lock Serial # 26670407 and later 4
F05011-4 Washer, 3/8” Split Lock Serial # 26660407 and prior 4
10 046760 Valve, Oil Drain 1
11 072588 2 Hose Clamp, 1/2” Spring 2
12 055895 Hose, Fuel 1/2” x 20” Long 1
13 P12724 Fitting, 3/8” NPT-3/8” Barb 1
14 P04332 Cap, 3/8” Pipe Galvanize 1
15 026396 Spacer, Clutch 1
16 029331 Sheave, BK60 1 1/8” 1
17 S21486 Key, 1/4” SQ x 3-3/8” Long 1
18 046143 Bushing, Clutch Spacer 1
19 F05011-117 Washer, 7/16” Nord-Lock 1
20 F81003-29 Bolt, M10-1.5 x 55mm Hex Head Full Thread G5 1
072684 3 Clutch Assembly, 5.75 Pitch 1 1/8 Bore 12V 1
21 0403113 1
22 059776 1
23 F05010-58 2
24 F05011-17 4
25 040338 1
26 F05011-33 2
27 F05006-27 2
28 044683 1
29 F05011-3 1
30 F05010-124 1
057507 Muffler, 29HP Kawasaki 49069-2356-Y Not Shown 1
056547 ECU, Kawasaki Not Shown 1
057002 Fan, Kawasaki Cooling-29HP Not Shown 1
072589 Screen, Radiator Kawasaki 29Hp Not Shown 1
4-10 Lastec//072815 Engine & Electrical
Engine & ElectricalEngine Assembly 4
NOTE: For further breakdown of the Kawasaki engine, see your Kawasaki Owner’s Man-ual or check www.kawpower.com.
1 Radiator holds 2.9 qt. (2.7L). Use 50/50 mix of antifreeze and water.2 Replaced (2) 061807 Hose Clamp, Dixon Worm Gear HSS6 (Serial #46570113 and later).3 Replaced 029330 Electric Clutch/Brake w/hardware (Serial #48470613 and later). When replacing the original 029330 Ogura clutch,
please order 072691 Retrofit Kit (not 072684 clutch assembly listed in the parts table above).
290002-1C
Engine & Electrical Lastec//072815 4-11
Engine & ElectricalRadiator Cowling Assembly4
4.6 Radiator Cowling Assembly
REF PART # DESCRIPTION COMMENTS QTY.
046719 Radiator Cowling Assembly 1
1 F05010-69 Nut, 1/4-20 Nylon Lock 4
2 046739 Spring, Cowling Hinge 2
3 F05010-9 Nut, 1/4-20 Keps 2
4 F05005-101 Bolt, 1/4-20 x 1” Hex Head Grade 5 2
5 F05010-160 Nut, 10-24 Hex Nylock 2
6 P06104 Foot, Rubber 2
7 046668 Cowling Weldment, 29HP Engine 1
8 F05004-35 Screw, 10-24 x 1/2” SBHC 2
9 P111 Ring, 1” Kick-Out 2
10 F05011-3 Washer, 3/8” Flat SAE 2
11 046270 Rod Weldment, Cowling Pivot 1
12 F05005-123 Bolt, 1/4-20 x 3/4” Hex Head Grade 5 2
4-12 Lastec//072815 Engine & Electrical
Engine & ElectricalRadiator Cowling Assembly 4
290002-3
Engine & Electrical Lastec//072815 4-13
Engine & ElectricalMotor Mount and Hardware4
4.7 Motor Mount and Hardware
REF PART # DESCRIPTION COMMENTS QTY.
1 F05007-136 Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5 4
2 F05011-3 Washer, 3/8” Flat SAE 4
3 F05010-14 Nut, #10-24 Keps 4
4 F05011-18 Washer, #10 SAE Flat 4
5 P07584 Clamp, 1/2” EMT Coated 4
6 F05004-18 Screw, 10-24 x 5/8” Unsl Indent HH Machine 4
7 049564 Mount Weldment, Engine 1
8 F05010-10 Nut, 3/8-16 Hex Nyloc 4
9 P294 Fitting, 1/4-28 45 Deg Grease 1
10 027009 Guard, Right Hydro Fan 1
11 056244 Guard, Left Hydro Fan 1
12 F05006-101 Bolt, 5/16-18 x 3/4” Hex Head W/Flat&Lock Washer 2
13 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 1
14 F05011-68 Washer, 1/2” Standard Flat Zn 1
045271 Pulley Assembly, 5” OD Idler, V Groove 1
15 F04254-12 Ring, 62mm IR Din #472 Retaining 2
16 045270 Pulley, 5” OD Idler, V Groove 1
17 P103 Bearing, Spindle Top 6305 RS 1
18 045272 Boss, Idler Pulley Standoff 1
19 F05010-8 Nut, 1/2-13 Nylon Hex Lock 1
20 049705 Idler Assembly, Deck Drive See Section 4.8 for parts 1
050436 Relay, 40A 12VDC Automotive Not Shown 3
4-14 Lastec//072815 Engine & Electrical
Engine & ElectricalMotor Mount and Hardware 4
290001-1
Engine & Electrical Lastec//072815 4-15
Engine & ElectricalDeck Drive Idler Assembly4
4.8 Deck Drive Idler Assembly
Ring, 62mm IR Din #472 Retaining
Pulley, 5” OD Idler, V Groove
Bearing, Spindle Top 6305 RS
Boss, Idler Pulley Standoff
REF PART # DESCRIPTION COMMENTS QTY.
049705 Idler Assembly, Deck Drive 1
1 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 1
2 F05011-68 Washer, 1/2” Standard Flat Zn 1
045271 Pulley Assembly, 5” OD Idler, V Groove 1
3 F04254-12 2
4 045270 1
5 P103 1
6 045272 1
7 049702 Plate Weldment, Deck Drive Idler 1
8 F05010-8 Nut, 1/2-13 Nylon Hex Lock 1
9 P786 Bushing, 3/4” ID x 1” OD x 5/8” Lng Flanged 2
10 F05012-115 Pin, 3/4” Clevis Retaining 1
11 F05012-21 Pin, 3/16” x 1” Cotter 1
12 026472 Tensioner Bushing 2
13 049701 Boss Weldment, Rubber Spring Tensioner 1
14 F05010-35 Nut, 1/2-13 Hex 2
15 F05011-2 Washer, 1/2” SAE Flat 1
16 049869 Spring, Urethane 1
17 F05011-5 Washer, 5/8” SAE Flat 1
4-16 Lastec//072815 Engine & Electrical
Engine & ElectricalDeck Drive Idler Assembly 4
LT0081
Engine & Electrical Lastec//072815 4-17
Engine & ElectricalAir Filter Assembly4
4.9 Air Filter Assembly
Housing, Engine Air Filter
Air Filter, Inner Element
Air Filter, Primary Element
Housing Cap, Kohler Filter
Housing Cap Dirt Ejector, Kohler Filter
REF PART # DESCRIPTION COMMENTS QTY.
046783 Air Filter Assembly 1
1 046556 Hood, Rain 1
2 P09895 Clamp, 2 1/2” Worm 3
3 046786 Filter Bracket Weldment 1
4 F05004-237 Screw, M8 x 1.25 x 60 Hex Washer Hd w/o Serr Metric 1
5 046781 Bushing, Clamp Spring 1
6 046782 Spring, Filter Clamp 1
7 046785 Bracket, Upper 1
8 F05004-238 Screw, M8 x 1.25 x 14 Hex Washer Hd w/o Serr Metric 2
9 046788 Pipe, Intake 1
10 046787 Duct, Upper 1
046789 Filter Assembly, Engine Air 1
11 046780 1
12 046554 1
13 046553 1
14 046552 1
073357 Not Shown
057501 Gauge, Kawasaki Air Filter Minder Not Shown 1
4-18 Lastec//072815 Engine & Electrical
Engine & ElectricalAir Filter Assembly 4
290002-2
Engine & Electrical Lastec//072815 4-19
Engine & ElectricalBattery Tray Assembly4
4.10 Battery Tray Assembly
Box, Battery Modified
Bolt, 5/16-18 x 8-1/2” Hex Head Grade 5
Angle, Battery Hold Down
Washer, Felt Battery Terminal
Battery, Group 26 w/Handle
Bolt, 5/16-18 x 1” Hex Head Grade 5
Washer, 5/16” Split Lock
Washer, 5/16” SAE Flat
Channel, Battery Box Spacer
Strap, 24” Rubber w/Hooks
Nut, 1/4-20 Nylock
Washer, 1/4” SAE Flat
Bolt, 1/4-20 x 1 1/4” Hex Head Grade 5
REF PART # DESCRIPTION COMMENTS QTY.
044696 Tray Assembly, Commercial Battery 1
049700 Battery Assembly, 33HP 1
1 049599 1
2 F05006-123 2
3 026382 1
4 P12161 1
5 067381 1
6 F05006-27 2
7 F05011-13 2
8 F05011-17 2
9 049769 1
10 P11258 1
11 F05010-69 1
12 F05011-11 1
13 F05005-116 1
14 049896 Bracket, Left Seat Latch 1
15 049895 Bracket, Right Seat Latch 1
16 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc 4
17 F05011-13 Washer, 5/16 Split Lock 4
18 042985 Plate Weldment, Battery Tray 1
19 028352 Clamp,1” ID Coated 1
4-20 Lastec//072815 Engine & Electrical
Engine & ElectricalBattery Tray Assembly 4
LT0075B
Engine & Electrical Lastec//072815 4-21
Engine & ElectricalWiring Harness4
4.11 Wiring Harness
Wire # Gauge Color/Stripe From - To
1 1A-B 6 Red Bat +, Starter2 2A-B 6 Black Bat (neg), Eng Gnd3 2C-D 16 Black Eng Gnd, Seat Delay4 2E-F 16 Black Seat Delay, CR3 - 865 2G-H 16 Black CR3 - 86, CR2 - 866 2J-K 16 Black CR2 - 86, CR1 - 307 2L-M 16 Black CR1 - 30, CR1 - 868 2N-P 16 Black CR1 - 86, Key Switch - G9 2Q-R 16 Black Key Switch - G, Splice
10 2S-T 16 Black Splice, Hour Meter11 2U-V 16 Black Splice, Aux Power Outlet12 2W-X 16 Black Eng Gnd, Fuel Pump (neg)13 2Y-Z 16 Black Eng Gnd, Clutch14 3A-B 14 Red Starter +, Splice15 3C-D 14 Red F4 (25A), Eng616 4A-B 16 Red/Black Key Switch - B, Splice17 4C-D 16 Red/Black Splice, F2 (10A)18 4E-F 16 Red/Black Splice, Blade Switch com C (NC)19 4G-H 16 Red/Black Blade Switch com C (NC), Oil Pressure Lamp20 4J-K 16 Red/Black Splice, Diagnostic Lamp21 4L-M 16 Red/Black Splice, Over Temp Alarm22 4N-P 16 Red/Black Key Switch - B, Seat23 4Q-R 16 Red/Black Seat, Brake 124 4S-T 16 Red/Black Brake 1, CR2 - 3025 4U-V 16 Red/Black CR2 - 30, Splice26 4W-X 16 Red/Black Splice, Eng627 5A-B 16 Red/Blue F1 (20A), Key Switch - L28 6A-B 16 White/Violet Blade Switch com C (NC), Right Neutral29 7A-B 16 Orange Right Neutral, Left Neutral30 8A-B 16 Orange/White Left Neutral, Brake 234 9A-B 16 Green Brake 2, CR3 - 8535 10A-B 16 Green/White Hour Meter +, Blade Sw com B (NO)36 10C-D 16 Green/White Blade Sw com B (NO), Left Neutral37 10E-F 16 Green/White Left Neutral, Brake 138 10G-H 16 Green/White Brake 1, Seat39 11A-B 16 Yellow/Black Right Neutral, Left Neutral41 12A-B 16 White Right Neutral, Brake 1 (NC)42 12C-D 16 White Brake 1 (NC), D1 Diode +43 12E-F 16 White D1 Diode (neg), CR1 - 8544 13A-B 16 White/Blue Blade Sw com B, Brake 145 14A-B 16 Green/Orange Blade Sw com B, CR2 - 8546 15A-B 16 Red/Green Key Switch - S, CR3 - 3047 16A-B 16 Red/Yellow CR4 - 87, Fuel Pump +48 17A-B 16 Black/White CR1 - 87, Eng349 18A-B 16 Brown CR4 - 86, Eng350 19A-B 16 Yellow CR2 - 87, Clutch 51 20A-B 16 Blue CR3 - 87, Starter Solenoid52 21A-B 16 Blue/Red Oil Pressure Lamp -, Eng653 22A-B 16 Black Key Switch - M, Eng654 23A-B 16 Red CR1 - 85, Clutch Delay55 24A-B 16 Red/White Eng3, Diagnostic Lamp56 25A-B 16 Yellow/White Over-Temp Alarm, Eng657 26A-B 16 Gray F3 (10A), CR4 - 8558 26C-D 16 Gray CR4 - 85, CR4 - 3059 26E-F 16 Gray CR4 - 30, Eng3 (Bullet)
29- 61-73AGC Kawasaki Harness Color Code rev. B.01Lastec Item #
*** All Wire Stranded GXL ***
4-22 Lastec//072815 Engine & Electrical
Engine & ElectricalWiring Harness4
5/8"
Loo
m
Bra
ke 1
8"4"
Bra
ke 2
Tape
Hou
r M
eter
NC
Tape x4
14"
Left
Neu
tral 16
"
Rig
htN
eutr
al
3/8"
Loo
m
AB
CNC
NO
Aux
Pow
erO
utle
t11
"
25"
Key
Sw
itch
G S
B
LM
¼"
FI Q
uick
Fe
mal
e x2
LN,R
N,B
rake
1,B
rake
2-H
ousi
ng, P
acka
rd p
/n 2
9770
48. C
onta
cts,
p/n
296
5142
(F/1
4-16
).
Clu
tch
Del
ay-H
ousi
ng, P
acka
rd p
/n 2
9738
72. C
onta
cts,
p/n
296
5142
(F/1
4-16
).
Bla
de-H
ousi
ng, D
elta
Sys
tem
s p/
n 97
2306
. Con
tact
s, P
acka
rd p
/n 2
9651
42(F
/14-
16).
Key
-Hou
sing
, Pac
kard
p/n
029
7342
2. C
onta
cts,
p/n
296
2142
(F/1
4-16
).
F1,F
2,F3
,F4,
-Hou
sing
/Wire
, Bus
sman
n p/
n H
HM
.
Tape
All
Loom
End
s
Con
nect
ors
view
ed fr
om w
ire e
ntry
All
Loom
Mus
t Be
Hig
h Te
mpe
ratu
re Id
entif
ied
With
Str
ipe
NO
TE:
Eng
Gnd
5" 5/16
NI
Rin
gx2
Clu
tch
12"
5"4"
Red
Boo
tB
lack
Boo
t
Tape
Fuel
P
ump10
"
Eng
3
20"
3/16
FI F
em
Qui
cks
Red
Boo
t M
etro
p/n
M23
507
5/16
NI
Rin
gx2
30
8787A
85
86
30
8787A
85
8630
8787A
85
86
30
8787A
85
86
Met
ro p
/n M
2350
1M
etro
p/n
M23
500
Soc
kets
Vie
wed
from
R
elay
Inse
rtio
n!!
!!!!
Bla
deS
witc
hS
plic
e
CR
1,C
R2,
CR
3, C
R4
-Hou
sing
, Bos
ch p
/n 3
3344
8500
8. C
onta
cts,
Am
p p/
n 60
253-
2 (1
6/14
ga).
Eng
3-H
ousi
ng, P
acka
rd p
/n 8
9051
17. C
onta
cts,
p/n
296
2987
(M/1
4-16
).
Clu
tch
-Hou
sing
, Pac
kard
p/n
298
4883
. Con
tact
s, p
/n 2
9629
87.
Eng
6-H
ousi
ng, P
acka
rd p
/n 0
2977
042.
Con
tact
s, p
/n 2
9629
87(M
/14-
16).
F1=
20A
F2=
10A
F3=
10A
F4=
25A
5 =
RE
D /
BLU
E
4 =
RE
D /
BLA
CK
3 =
RE
D
2 =
BLA
CK
1 =
RE
D
9 =
GR
EE
N
7 =
OR
AN
GE
6 =
WH
ITE
/ V
IOLE
T
8 =
OR
AN
GE
/ W
HIT
E
10 =
GR
EE
N /
WH
ITE
11 =
YE
LLO
W /
BLA
CK
16 =
RE
D /
YE
LLO
W
15 =
RE
D /
GR
EE
N
14 =
GR
EE
N /
OR
AN
GE
13 =
WH
ITE
/ B
LUE
12 =
WH
ITE
20 =
BLU
E
18 =
BR
OW
N
17 =
BLA
CK
WH
ITE
19 =
YE
LLO
W
25 =
YE
LLO
W /
WH
ITE
10
+-
+ -
-+
+
-
F2
20F1
Tape
Tape
10 F3
Tape
¼"
FI Q
uick
Fe
mal
e x2
Ove
r-Te
mp
Ala
rm
3/8"
Loo
m
Dia
gnos
ticLa
mp
Oil
Pre
ssur
eLa
mp
3/16
" FI
Qui
ck
Fem
ale
x4
21 =
BLU
E /
RE
D
WIR
E C
OLO
R
MA
TRIX
CO
NN
EC
TOR
, TE
RM
INA
L, F
US
E H
OLD
ER
M
ATR
IX
FUS
E M
ATR
IX
Sea
t
3/8"
Loo
m
4"
2"
5"
2"
Eng
6
5"
3"
Sta
rter
Sol
enoi
dS
tart
er
10"
22 =
BLA
CK
23 =
RE
D
24 =
RE
D /
WH
ITE
¼"
FI Q
uick
Fe
mal
e x2
Tape
# 8
NI R
ing
x2 7"
7"7"
7"
53"
4" x24"
10"
4"
6"7"Ta
pe8"
Clu
tch
Del
ay
+- Tape1"
5/8"
Loo
m
4" x2
Tape
Tape
.156
FI
Fem
ale
Bul
let
25F4
4"
1/2"
Loo
m
4A,N2P,Q
22A
4C,E
,J,L
4B
4M2T
4K
4H
4F,G
Spl
ice
2U,S
2R
4D
2V
4P,Q
4R,S
2F,G
4T,U
2H,J
2K,L
2M,N
4V,W
Spl
ice
2D,E
2A
2C,W
,Y2B
2X
4X22B
++
5/8"
Loo
m
1/4"
Loo
m
3D
1A
5B
Spl
ice
1B3A
3BF4,F
1
5A 3C7"
Tape
1/4
FI F
em
Qui
ck
6A
6B 7A
7B
8A
8B
9A
9B
10A
10B
,C
10D
,E
10F,
G10
H
11A
11B
12A
12B
,C
¼"
FI Q
uick
Fe
mal
e x
2
1"1"
12E
12D
Tape
Tape
D1,
Dio
de
-
12F
13A
13B
14A
14B
15A
15B
16A 16
B
17A
17B
18B
18A
19A
19B
20B
20A
21B
+ -21
A23
A
23B
24A
25B
24B
-+
2Z
25A
26A
26B
,C
26D
,E
26F
+
26 =
GR
AY
Bat
tery
1"
4-24 Lastec//072815 Engine & Electrical
Engine & ElectricalWiring Harness 4
29-61,73 Kawasaki Rev. B.01
F120A
25A
L
B
S
START
CLUTCH
CR1
CR2
CR3
Seat Sw
CR4
Eng3
F3
10A
RectifierRegulator
CR4 Eng3ECU
ECU
brn
Starter/Batt
Eng6 Eng*ECU
Regyel/wht
org
wht
30 87
30 87
30 87
85 86
Fuel Pump
red
red/blu
blk
blk
blk
blk
red/yel
red/grn
red/blk yel
blu
blk/wht
G
B
S
L
M
POSITION FUNCTION CONTACTS123
OFFRUN
START
G & ML & B
L & B & S
Key Switch
3087
Exbullet
Eng6 red
brn
G
M
gry
CR3
START
CR2
CLUTCH
CR1
OP PRESENT
Blade SW
Blade SW
OFF
OFF
Hour Meter
85 86
85 86
85 86
red/blk blk
blk
blk
blk
org/wht grn
grn/org
org
grn/wht
grn/wht
wht/vio
DELAYwht
F2
10A
com B
com C
OFF OFF
grn/wht yel/blk wht
wht/bluBrake1Brake1 Blade SW
OFF
com B
Aux PP
red/blk
red/blk
Seat LN RN
RN LN Brake2
OFF
red blk
D2
Eng Chassis
R
Water Temp
Alarm
Eng6red/blk
Eng6
ECUblkblk
Eng3
ECUredred/blk
Diagnostic
R
Eng6 blu/redred/blkOil Press
red/wht
blu/red
blk
yel/wht yel
Engine & Electrical Lastec//072815 4-25
Lastec//072815 5-1
5
SECTION 5 61” MOWER DECK
61 in DeckDeck Framework5
5.1 Deck Framework
REF PART # DESCRIPTION COMMENTS QTY.
1 049855 Belt, B-128 Deck Drive 1
2 041645 Grass Chute Assembly 1
3 049490 Deck Weldment, 61” Articulating #3 1
4 049512 Deck Weldment, 61” Center 1
5 055835 Deck Weldment, 61” Articulating #1 Serial # 2850806 and later 1
049532 Deck Weldment, 61” Articulatin #1 Serial # 2849806and prior 1
5-2 Lastec//072815 61 in Deck
61 in DeckDeck Framework 5
LT0042
61 in Deck Lastec//072815 5-3
61 in DeckDeck 1 Hardware (Serial # 2860806 and later)5
5.2 Deck 1 Hardware (Serial # 2860806 and later)
Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5
Nut, 5/8-11 FlexLoc
Deck Weldment, 61” Articulating #1
Nut, 3/8-16 Flanged Hex Nyloc
Cover, 61A Deck #1
Spindle Assembly, ZT 21” D6.3-6.3
REF PART # DESCRIPTION COMMENTS QTY.
055834 Deck Assembly, 61” Articulating #1 1
1 F05009-20 2
2 F05010-185 2
3 055835 1
4 F05010-222 3
5 055803 1
6 067695 1
1 Replaces 049892 2861AGC Double Sheave Spindle Assembly (See Section 5.10 for parts) (5/14 and later).
See Section 5.8 for parts 1
5-4 Lastec//072815 61 in Deck
61 in DeckDeck 1 Hardware (Serial # 2860806 and later) 5
LT0043B
61 in Deck Lastec//072815 5-5
61 in DeckDeck 1 Hardware (Serial # 2850806 and prior)5
5.3 Deck 1 Hardware (Serial # 2850806 and prior)
NOTE: If using the rear discharge system, items 1,2,3 and 4 are not used.
NOTE: After Serial # 2850806, the rear bolt-on baffle was replaced with a full pan wrap around the deck weldment.
REF PART # DESCRIPTION COMMENTS QTY.
1 F05006-27 Bolt, 5/16-18 x 1” Hex Head Grade 5 2
2 F05011-17 Washer, 5/16” SAE Flat 3
3 049781 Baffle, Outside Rear Bolt-On 1
4 F05010-58 Nut, 5/16-18 Nylok Hex 2
5 F05009-20 Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5 2
6 F05010-185 Nut, 5/8-11 FlexLoc 2
7 049532 Deck Weldment, 61 Articulatin #1 1
8 F05010-10 Nut, 3/8-16 Hex Nyloc Added after serial # 2410406 3
9 F05011-3 Washer, 3/8” Flat SAE Added after serial # 2410406 3
10 055803 Cover, 61A Deck #1 Added after serial # 2410406 1
5-6 Lastec//072815 61 in Deck
61 in DeckDeck 1 Hardware (Serial # 2850806 and prior) 5
049535
61 in Deck Lastec//072815 5-7
61 in DeckDeck 2 Hardware5
5.4 Deck 2 Hardware
NOTE: If using the rear discharge system, items 20-25 are not used.
Item 2 and 8: Apply water-proof axle grease to mating surfaces prior to assembly.
REF PART # DESCRIPTION COMMENTS QTY.
1 049512 Deck Weldment, 61” Center 1
2 049870 Bushing, Urethane Pivot 2 Added after Serial #2790806 1
049510 Bushing, Rubber Pivot Serial #2780806 and priorNo longer available; order 049870
1
3 049894 Link, Front Deck Lift 4
4 P110 Pin, 3/8” x 1 5/16” Clevis, Yzn 2
5 P111 Ring, Kick-out, 1” 3
6 F04254-46 Ring, 3/4” External - External 1
7 F05011-77 Washer, 3/4” AN Yel/Cad 1
8 F05010-8 Nut, 1/2-13 Nylon Hex Lock 2
9 P212 Pin, 3/8” x 2 1/8” Clevis, Yzn 1
10 F05008-23 Bolt, 1/2-13 x 3” Hex Head Grade 5 1
11 F05011-9 Washer, 1/2” Split Lock 1
12 062051 Washer, Water Shed Pulley 1
045271 Pulley Assembly, 5” OD Idler, V Groove Serial # 33151108 and later 1
043543 Pulley, 5” OD V-Groove Idler No longer available: order 045271 Serial # 33141108 and prior
1
13 F04254-12 Ring, 62mm IR Din #472 Retaining 2
14 P103 Bearing, Spindle Top 6305 RS 1
15 045270 Pulley, 5” OD Idler, V Groove 1
16 045297 Boss, Idler Pulley Standoff 1
17 049868 Spacer, .53” ID x 1 1/4” OD x 1 1/4” Lng 1
18 F05007-165 Bolt, 3/8-16 x 1” Carriage, Zinc Grade 5 2
19 F05010-222 Nut, 3/8-16 Flanged Hex Nylon Lock 2
20 049784 Baffle, Outside Rear Bolt-On 1
21 F05006-27 Bolt, 5/16-18 x 1” Hex Head Grade 5 1
22 F05011-17 Washer, 5/16” SAE Flat 2
23 F05010-58 Nut, 5/16-18 Nylon Lock Hex 1
24 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc 1
25 F05011-13 Washer, 5/16” Split Lock 1
26 027013 Wheel, Anti-Scalp, 5-5/8" hole 1
27 F05009-10 Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 1
28 072497 Spacer, 1 OD x .65 ID x .53 Long 1
29 F05010-224 Nut, 5/8-11 Flanged Hex Nylock 1
30 067695 1
1 Replaces 049892 2861AGC Double Sheave Spindle Assembly (See Section 5.10 for parts) (5/14 and later).
Spindle Assembly, ZT 21” D6.3-6.3 See Section 5.8 for parts 1
5-8 Lastec//072815 61 in Deck
61 in DeckDeck 2 Hardware 5
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
LT0030B
61 in Deck Lastec//072815 5-9
61 in DeckDeck 3 Hardware5
5.5 Deck 3 Hardware
Washer, 5/16” SAE Flat
Nut, 5/16-18 Flanged Nylok Hex
Bolt, 5/16-18 x 1” Hex Head Grade 5
Baffle, Outside Rear Bolt-On
Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5
Nut, 5/8-11 FlexLoc
Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Grade 5
Deck Weldment, 61” Articulating #3
Cover, 61A Deck #3
Nut, 3/8-16 Flanged Hex Nyloc
Grass Chute Assembly
Spindle Assembly, ZT 21” D6.3-6.3
NOTE: If using the rear discharge system, items 1,2,3 and 4 are not used.
REF PART # DESCRIPTION COMMENTS QTY.
049526 Deck Assembly, 61” Articulating #3 1
1 F05011-17 2
2 F05010-221 2
3 F05006-27 1
4 049781 1
5 F05009-20 2
6 F05010-185 2
7 F05006-93 1
8 049490 1
9 055804 1
10 F05010-222 3
11 041645 See Section 5.13 for parts 1
12 067695 1
1 Replaces 049892 2861AGC Double Sheave Spindle Assembly (See Section 5.10 for parts) (5/14 and later).
See Section 5.8 for parts 1
5-10 Lastec//072815 61 in Deck
61 in DeckDeck 3 Hardware 5
LT0044-1B
61 in Deck Lastec//072815 5-11
61 in DeckRear Discharge Baffle Assembly5
5.6 Rear Discharge Baffle Assembly
Baffle Assembly, #3 Deck Mulching
Nut, 3/8-16 Flanged Hex Nyl Lock
Baffle Weldment, #3 Deck Mulching
Bolt, 3/8-16 x 1” Carriage Grade 5
Bolt, 3/8-16 x 1 1/2” Carriage Grade 5
Baffle Assembly, #2 Deck Rear Discharge
Baffle Weldment, #2 Deck Rear Discharge
Nut, 3/8-16 Flanged Hex Nyl Lock
Bolt, 3/8-16 x 1” Carriage Grade 5
NOTE: To use the rear discharge system, bolt in the rear discharge baffle weldments as shown here, and remove the factory installed rear baffle plates from decks 2 and 3. The factory installed baffle remains on deck 1.
NOTE: All units receive the rear discharge baffles -- use of the rear discharge system is optional. Rear Chute is only for use with units with serial # 2850806 and prior.
REF PART # DESCRIPTION COMMENTS QTY.
049997 Baffle Kit, Rear Discharge 1
049963 1
1 F05010-222 2
2 049873 1
3 F05007-165 1
4 F05007-85 1
049961 1
5 049960 1
6 F05010-222 3
7 F05007-165 3
8 055452 Kit, Rear Discharge Chute Serial # 2850806 and prior 1
5-12 Lastec//072815 61 in Deck
61 in DeckRear Discharge Baffle Assembly 5
LT0048B
Factory installedBaffle removed
Factory installed Baffle removed
Factory installedBaffle remains
61 in Deck Lastec//072815 5-13
61 in DeckOptional Mulching Kit5
5.7 Optional Mulching Kit
This mulching kit may be purchased through your Lastec Dealer.
To properly use the mulching feature, the Deck 3 Baffle 049963 from the rear dischargekit must also be in place. The 049963 Deck 3 Baffle Includes the unit in a separate box aspart of the Rear Discharge Baffle Assembly. All factory installed rear baffles remain inplace for mulching.
REF PART # DESCRIPTION COMMENTS QTY.
049998 Baffle Kit, Mulching 61AGC 1
049962 Baffle Assembly, #2 Deck Mulching 1
1 F05010-222 Nut, 3/8-16 Flanged Hex Nylock 3
2 049877 Baffle Weldment, #2 Deck Mulching 1
3 F05007-165 Bolt, 3/8-16 x 1” Carriage Grade 5 3
049964 Baffle Assembly, #1 Deck Mulching 1
4 049866 Baffle Weldment, #1 Deck Mulching 1
5 F05010-222 Nut, 3/8-16 Flanged Hex Nylock 2
6 F05007-165 Bolt, 3/8-16 x 1” Carriage Grade 5 2
7 P322 Blade, 21” Gator Mulching 3
5-14 Lastec//120315 61 in Deck
61 in DeckOptional Mulching Kit 5
LT0047C
61 in Deck Lastec//120315 5-15
Mower DecksDouble Pulley Spindle (5/14 and later)5
5.8 Double Pulley Spindle (5/14 and later)
Fitting, 1/4-28 Straight Grease
Bolt, Spindle Single Pulley
Washer, 1/2” Plain Belleville
Key, 1/4” Square x 1 1/2” Long
Sheave, Double - Mower Deck
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
Spindle Assembly, ZT Cast
Nut, 3/8-16 Flanged Hex Nyloc
Blade, 21” x 2 1/2” x 1/4” High Lift
Blade, 21” Low-Lift
Blade, 21” Gator Mulching
Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra
Washer, 2 1/2” x 11/16” x 3/16” Nylon
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
REF PART # DESCRIPTION COMMENTS QTY.
067695 Spindle Assembly, ZT 21” D6.3-6.3 Non-saleable item. Parts must be purchased separately.
1
1 P107 1
1 For service order 067354 Spindle Bolt 1 1/4” Service Kit including (1) P107 1/4-28 Straight Grease Fitting and (1) 045677 Spindle Single Pulley Bolt.
1
2 0456771 Maximum Torque: 57 ft-lbs 1
3 F05011-97 1
4 028080 1
5 067688 1
6 F05007-78 4
7 067696 See Section 5.9 for parts 1
8 F05010-222 4
9 P128 1
P246 Optional 1
P322 Optional 1
063265 Optional 1
10 029889 1
11 F05011-89 Remove to install Anti-Scalp Blade Disc
1
12 F05009-95 Torque Value: 75 ft-lbs 1
13 048898 Blade Disc, Anti-Scalp Optional part. Remove Item 11 to install Anti-Scalp Blade Disc
1
5-16 Lastec//072815 Mower Decks
Mower DecksDouble Pulley Spindle (5/14 and later) 5
100_190
Mower Decks Lastec//072815 5-17
Mower DecksSpindle Housing5
5.9 Spindle Housing
Bearing, 6206-2NSE
O-Ring, 2 1/2” ID x 2 3/4” OD
Spacer, Bearing Housing
Spindle Housing, ZT- Common Core
Spacer, Spindle Bearing Housing
Washer, 1.50” x 1.185” x 16Ga
Washer, 2.435” x 1.185” x 11Ga
Shaft, Blade Spindle ZT Cast
Concerning Nachi Sealed Bearings:
One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubri-cating the bearings forces the motor to work harder.
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full
Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.
Only a small of grease is required to lubricate a bearing in motion.
When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.
When using open bearings, pack the bearing as follows:
REF PART # DESCRIPTION (Indicates Non-Saleable Items) COMMENTS QTY.
067696 Spindle Assembly, Center w/Stiffener Non-saleable item. Parts must be purchased separately.
1
1 P11035 3
2 P105 4
3 072511 1
4 067999 1
5 067686 1
6 034947 1
7 034948 1
8 067687 1
5-18 Lastec//072815 Mower Decks
Mower DecksSpindle Housing 5
100_188
Mower Decks Lastec//072815 5-19
61 in DeckDouble Pulley Spindle (Prior to 5/14)5
5.10 Double Pulley Spindle (Prior to 5/14)
Fitting, 3/16” x 3/16” Straight Grease
Bolt, Spindle Single Pulley
Washer, 1/2” Plain Belleville
Key, 1/4” x 2 1/2”
Sheave, Double - 2561 Mower
Washer, 1/4” x 1.47” x 1.01”
Bolt, 3/8-16 x 1 1/2” Carriage Grade 5
Plate, Deck Reinforcing
Plate, Deck Reinforcing
Spindle Assembly, Center w/Stiffener
Nut, 3/8-16 Hex Nyloc
Blade, 21” x 2 1/2” x 1/4” High Lift
Blade, 21” Low-Lift
Blade, 21” Gator Mulching
Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra
Washer, 2 1/2” x 11/16” x 3/16” Nylon
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat
Washer, 5/8” Split Lock
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
REF PART # DESCRIPTION COMMENTS QTY.
049892 Spindle Assembly, 2861AGC Double Sheave Non-saleable item. Parts must be purchased separately.
1
1 P04107 1
2 045677 Maximum Torque: 57 ft-lbs 1
3 F05011-97 1
4 027053 1
5 040049 1
6 046273 1
7 F05007-85 4
8 044862 Serial # 2940906 and later 2
048183 Serial # 2930806 and prior 1
9 043246 See Section 5.11 for parts 1
10 F05010-10 4
11 P128 1
P246 Optional 1
P322 Optional 1
063265 Optional 1
12 029889 1
13 F05011-89 Serial # 2940906 and later. Remove to install Anti-Scalp Blade Disc
1
F05011-27 Serial # 2930806 and prior 1
14 F05009-95 Torque Value: 75 ft-lbs 1
15 048898 Blade Disc, Anti-Scalp Optional part. Remove Item 13 to install Anti-Scalp Blade Disc
1
5-20 Lastec//072815 61 in Deck
61 in DeckDouble Pulley Spindle (Prior to 5/14) 5
LT0033
61 in Deck Lastec//072815 5-21
61 in DeckSpindle Housing5
5.11 Spindle Housing
Bolt, 5/16-18 x 5” Hex Head Grade 5
Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5
Washer, 5/16” Split Lock
Plate, Deck Reinforcing
Seal, 2561 Spindle
Collar, Spindle Top
O-Ring, Spindle
Bearing, 6206-2NSE
Housing, Spindle
Pin, 1/8” x 1/2” Roll
Nut, 5/16-18 Nylon Lock Hex
Spacer, Spindle Bearing
O-Ring, 2 7/16" ID x 3/16" Diameter
Washer, 1.50” x 1.185” x 16Ga
Washer, 2.435” x 1.185” x 11Ga
Shaft, Center Blade Spindle
Concerning Nachi Sealed Bearings:
One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubri-cating the bearings forces the motor to work harder.
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full
Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.
Only a small of grease is required to lubricate a bearing in motion.
When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.
When using open bearings, pack the bearing as follows:
REF PART # DESCRIPTION COMMENTS QTY
043246 Spindle Assembly, Center w/Stiffener Non-saleable item. Parts must be purchased separately.
1
1 F05006-140 Added after serial # 33351208 3
2 F05006-93 3 deleted after serial # 33341208 3
3 F05011-13 3 deleted after serial # 33341208 3
4 034921 1
5 034969 1
6 034951 1
7 062999 Added after serial # 34990809 1
8 P11035 3
9 034945 1
10 F05012-64 1
11 F05010-58 Added after serial # 33351208 3
12 034950 1
13 F04254-45 2
14 034947 1
15 034948 1
16 043245 1
5-22 Lastec//072815 61 in Deck
61 in DeckSpindle Housing 5
LT0024B
61 in Deck Lastec//072815 5-23
61 in DeckTensioner Assembly5
5.12 Tensioner Assembly
Boss, Idler Pulley Standoff
Ring, 62mm IR Din #472 Retaining
Bearing, Spindle Top 6305 RS
Pulley, 5” OD Idler, Flat
Pulley, 5” OD Idler
REF PART # DESCRIPTION COMMENTS QTY
049797 Idler Assembly, Deck Drive 1
1 F05010-222 Nut, 3/8-16 Flanged Hex Nyloc 1
2 F05010-1 Nut, 3/8-16 Hex 1
3 034982 Spring, 1 1/2” OD x 8 1/2” x .195” 1
4 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 1
5 029842 Bushing, 3/4” ID x 1” OD x 1” Oil 2
6 047878 Idler Pivot Weldment 1
7 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 1
8 P294 Fitting, 1/4-28 45 Deg Grease 1
045295 Pulley Assembly, 5” OD Idler, Flat 1
9 045297 1
10 F04254-12 2
11 P103 1
12 045296 Serial # 33151108 and later 1
043367 Serial # 33141108 and prior 1
13 062051 Washer, Water Shed Pulley 1
14 F05010-223 Nut, 1/2-13 Flanged Nylon Hex Lock 1
15 F05011-104 Washer, 3/8 x 1-1/2 x 1/8 Thick Hardened 1
5-24 Lastec//072815 61 in Deck
61 in DeckTensioner Assembly 5
LT0029B
61 in Deck Lastec//072815 5-25
61 in DeckGrass Chute5
5.13 Grass Chute
Nut, 5/16-18 Nylok Hex
Spring, Deere RH Torsion
Grass Chute, John Deere
Bolt, 5/16-18 x 9” Hex Head Grade 5 Spcl
REF PART # DESCRIPTION COMMENTS QTY
041645 Grass Chute Assembly 1
1 F05010-58 1
2 041714 1
3 041572 1
4 F05006-110 1
5-26 Lastec//072815 61 in Deck
61 in DeckGrass Chute 5
LT0044-2B
61 in Deck Lastec//072815 5-27
61 in DeckRear Anti-scalp Roller (Prior to 5/14)5
5.14 Rear Anti-scalp Roller (Prior to 5/14)
Nut, 3/8-16 Hex Nyloc
Plate, Anti-Scalp Adjusting
Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5
Mount Weldment, Deck Anti-Scalp
Nut, 5/8-11 FlexLoc
Nut, 5/8-11 Jam
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
Bushing, Urethane Pivot
Nut, 5/8-11 Jam Nylon Lock
Wheel, Anti-Scalp, 5 5/8" hole
Bolt, 5/8-11 x 4” Hex Head Grade 5
NOTE: Lubricate all surfaces of the inner bushing (049870) with a water-proof axle grease prior to assembly.
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY
049795 Wheel Assembly, Deck Anti-Scalp 1
1 F05010-10 2
2 063201 1
1 Replaced Deck Lift Link Rod Assembly (046700) on units with serial #34660609 and later. NOTE: 063201 is retrofittable to all units produced to date. 046700 does not work on units with serial #34660609 and later.
1
3 F05007-123 2
4 049794 1
5 F05010-185 1
6 F05010-82 1
7 F05009-35 1
8 049870 1
9 F05010-96 1
10 027013 1
11 F05009-28 1
5-28 Lastec//072815 61 in Deck
61 in DeckRear Anti-scalp Roller (Prior to 5/14) 5
LT0046
61 in Deck Lastec//072815 5-29
Lastec//072815 6-1
6
SECTION 6 73” MOWER DECK
73 in DeckDeck Framework6
6.1 Deck Framework
REF PART # DESCRIPTION COMMENTS QTY.
1 048272 Belt, 72" Deck Drive 1
2 041645 Grass Chute Assembly 1
3 044632 Deck Weldment, 73 Articulating #3 1
4 044631 Deck Weldment, 73 Articulating #2 1
5 044630 Deck Weldment, 73 Articulating #1 1
6-2 Lastec//072815 73 in Deck
73 in DeckDeck Framework 6
LT0049
73 in Deck Lastec//072815 6-3
73 in DeckDeck 1 Hardware6
6.2 Deck 1 Hardware
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
Nut, 5/8-11 FlexLoc
Deck Weldment, 73” Articulating #1
Nut, 3/8-16 Flanged Hex Nylock
Cover, 61A Deck #1
Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5
Spindle Assembly, ZT 25” D6.3-6.3
REF PART # DESCRIPTION COMMENTS QTY.
055390 Deck Assembly, 73” Articulating #1 1
1 F05009-35 1
2 F05010-185 2
3 044630 1
4 F05010-222 3
5 055803 1
6 F05009-20 1
7 067694 1
1 Replaced 055444 73” Double Sheave Spindle Assembly (See Section 6.7) to improve durability (8/14).
See Section 6.5 for parts 1
6-4 Lastec//072815 73 in Deck
73 in DeckDeck 1 Hardware 6
LT0050B
73 in Deck Lastec//072815 6-5
73 in DeckDeck 2 Hardware6
6.3 Deck 2 Hardware
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY.
1 044631 Deck Weldment, 73” Articulating #2 Gas 1
2 049870 1
1 Lubricate all mating surfaces of Urethane Pivot Bushing (049870) with a water-proof axle grease prior to assembly.
Bushing, Urethane Pivot 6
048890 Plate Assembly, Deck Adjusting 2
3 055192 Bolt Weldment, Height Adjust Eye 1
4 F05010-29 Nut, 3/8-16 Jam 1
5 062950 Adjusting Weldment, Deck 1
6 P110 Pin, 3/8” x 1 5/16” Clevis, Yzn 2
7 P111 Ring, Kick-out, 1” 3
8 F04254-46 Ring, 3/4” External - External 1
9 F05011-77 Washer, 3/4” AN Yel/Cad 1
10 049894 Link, Front Deck Lift 2
11 P212 Pin, 3/8” x 2 1/8” Clevis, Yzn 1
12 F05010-223 Nut, 1/2-13 Flanged Hex Nylock 1
13 F05010-222 Nut, 3/8-16 Flanged Hex Nylock 3
048452 Pulley, 9” B-C Groove Idler 1
14 F04254-4 Ring, 1.575” ID 3000-156 Retaining Available with Pulley Only 1
15 P06030-2 Bearing, 6203-2NSL 17mm SRI-2 ABEC-1 Available with Pulley Only 1
16 048451 Pulley Weldment, 9“ Idler Available with Pulley Only 1
17 048453 Adapter, Idler Pulley Bore Available with Pulley Only 1
18 055405 Spacer, 73” Deck 1/2ID x 1-3/8 1
19 F05008-61 Bolt, 1/2-13 x 3 1/2” Hex Head Grade 5 1
20 F05010-10 Nut, 3/8-16 Hex Nylon Lock 2
21 F05007-165 Bolt, 3/8-16 x 1” Carriage, Zinc Grade 5 2
22 055424 Baffle Weldment, 73” #2 Deck 1
23 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 1
24 F05010-1 Nut, 3/8-16 Hex 1
25 F05011-104 Washer, 3/8” x 1-1/2” x 1/8” Thick Hardened 1
26 027013 Wheel, Anti-Scalp 5-5/8" Hole 1
27 F05010-224 Nut, 5/8-11 Flanged Hex Nylock 1
28 072497 Spacer, 1 OD x .65 ID x .53 Long 1
29 F05009-10 Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 1
30 072486 Spindle Assembly, 73” Gas Double Sheave See Section 6.10 1
6-6 Lastec//072815 73 in Deck
73 in DeckDeck 2 Hardware 6
LT0032B
73 in Deck Lastec//072815 6-7
73 in DeckDeck 3 Hardware6
6.4 Deck 3 Hardware
Nut, 3/8-16 Flanged Hex Nylock
Cover, 61A Deck #3
Deck Weldment, 73” Articulating #3
Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5
Nut, 5/8-11 FlexLoc
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
Baffle Assembly, #3 Deck Mulching 73”
Bolt, 3/8-16 x 1 1/2” Carriage Grade 5
Nut, 3/8-16 Flanged Hex Nylock
Baffle Weldment, #3 Deck Mulching 73”
Bolt, 3/8-16 x 1” Carriage Grade 5
Grass Chute Assembly
Spindle Assembly, ZT 25” D6.3-6.3
REF PART # DESCRIPTION COMMENTS QTY.
055392 Deck Assembly, 73” Articulating #3 1
1 F05010-222 3
2 055804 1
3 044632 1
4 F05009-20 1
5 F05010-185 2
6 F05009-35 1
055890 1
7 F05007-85 1
8 F05010-222 2
9 055891 1
10 F05007-165 1
11 041645 See Section 6.12 for parts 1
12 067694 1
1 Replaced 055444 73” Double Sheave Spindle Assembly (See Section 6.7) to improve durability (8/14).
See Section 6.5 for parts 1
6-8 Lastec//072815 73 in Deck
73 in DeckDeck 3 Hardware 6
LT0051B
73 in Deck Lastec//072815 6-9
Mower DecksDouble Pulley Spindle, Decks 1 and 3 (8/14 and later)6
6.5 Double Pulley Spindle, Decks 1 and 3 (8/14 and later)
Fitting, 1/4-28 Straight Grease
Bolt, Spindle Single Pulley
Washer, 1/2” Plain Belleville
Key, 1/4” Square x 1 1/2” Long
Sheave, Double - Mower Deck
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
Spindle Assembly, ZT Cast
Nut, 3/8-16 Flanged Hex Nyloc
Blade, 25” x 2 1/2” x 1/4” High Lift
Blade, 25” x 2 1/2” x 1/4” Low Lift
Blade, 25" Gator Mulching
Blade, 25” x 2 1/2” x 1/8” Low-Lift Ultra
Washer, 2 1/2” x 11/16” x 3/16” Nylon
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
REF PART # DESCRIPTION (Indicates Non-Saleable Items) COMMENTS QTY.
067694 Spindle Assembly, ZT 25” D6.3-6.3 Non-saleable item. Parts must be purchased separately.
1
1 P107 1
2 045677 Maximum Torque: 57 ft-lbs 1
3 F05011-97 1
4 028080 1
5 067688 1
6 F05007-78 4
7 067696 See Section 6.6 for parts 1
8 F05010-222 4
9 P701 1
P849 Optional 1
P848 Optional 1
063266 Optional 1
10 029889 1
11 F05011-89 Remove to install Anti-Scalp Blade Disc
1
12 F05009-95 Torque Value: 75 ft-lbs 1
13 048898 Blade Disc, Anti-Scalp Optional part. Remove Item 13 to install Anti-Scalp Blade Disc
1
6-10 Lastec//072815 Mower Decks
Mower DecksDouble Pulley Spindle, Decks 1 and 3 (8/14 and later) 6
120_085
Mower Decks Lastec//072815 6-11
Mower DecksSpindle Housing, Decks 1 and 3 (8/14 and later)6
6.6 Spindle Housing, Decks 1 and 3 (8/14 and later)
Bearing, 6206-2NSE
O-Ring, 2 1/2” ID x 2 3/4” OD
Spacer, Bearing Housing
Spindle Housing, ZT- Common Core
Spacer, Spindle Bearing Housing
Washer, 1.50” x 1.185” x 16Ga
Washer, 2.435” x 1.185” x 11Ga
Shaft, Blade Spindle ZT Cast
Concerning Nachi Sealed Bearings:
One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubri-cating the bearings forces the motor to work harder.
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full
Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.
Only a small of grease is required to lubricate a bearing in motion.
When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.
When using open bearings, pack the bearing as follows:
REF PART # DESCRIPTION (Indicates Non-Saleable Items) COMMENTS QTY.
067696 Spindle Assembly, Center w/Stiffener Non-saleable item. Parts must be purchased separately.
1
1 P11035 3
2 P105 4
3 072511 1
4 067999 1
5 067686 1
6 034947 1
7 034948 1
8 067687 1
6-12 Lastec//072815 Mower Decks
Mower DecksSpindle Housing, Decks 1 and 3 (8/14 and later) 6
100_188
Mower Decks Lastec//072815 6-13
73 in DeckDouble Pulley Spindle, Decks 1 and 3 (Prior to 8/14)6
6.7 Double Pulley Spindle, Decks 1 and 3 (Prior to 8/14)
Fitting, 1/4-28 Straight Grease
Bolt, Spindle Single Pulley
Washer, 1/2” Plain Belleville
Key, 1/4” x 2-1/2”
Sheave, Double - 2561 Mower
Washer, 1.50” x 1.185 x 16Ga
Washer, 3/8” x 1.5 x 1.01”
Bolt, 3/8-16 x 1 1/2” Carriage Gr5
Plate, Deck Reinforcing
Plate, Deck Reinforcing
Spindle Assembly, Center w/Stiffener
Nut, 3/8-16 Hex Nyloc
Blade, 25” x 2 1/2” x 1/4” High Lift
Blade, 25” x 2 1/2” x 1/4” Low Lift
Blade, 25" Gator Mulching
Blade, 25” x 2 1/2” x 1/8” Low-Lift Ultra
Washer, 2-1/2” x 11/16” x 3/16” Nylon
Washer,2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc
Washer, 5/8” Split Lock
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
REF PART # DESCRIPTION COMMENTS QTY.
055444 Spindle Assembly, 73” Double Sheave Non-saleable item. Parts must be purchased separately.
1
1 P107 1
1 P107 replaced P04107 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).
1
2 045677 Maximum Torque: 57 ft-lbs 1
3 F05011-97 1
4 027053 1
5 040049 1
6 034947 1
7 043249 1
8 F05007-85 4
9 044862 Serial # 2940906 and later 2
048183 Serial # 2930806 and prior 1
10 043246 See Section 6.8 for parts 1
11 F05010-10 4
12 P701 1
P849 Optional 1
P848 Optional 1
063266 Optional 1
13 029889 1
14 F05011-89 Serial # 2940906 and later.Remove to install Anti-Scalp Blade Disc
1
F05011-27 Serial # 2930806 and prior 1
15 F05009-95 Torque Value: 75 ft-lbs 1
16 048898 Blade Disc, Anti-Scalp Optional part. Remove Item 13 to install Anti-Scalp Blade Disc
1
6-14 Lastec//072815 73 in Deck
73 in DeckDouble Pulley Spindle, Decks 1 and 3 (Prior to 8/14) 6
LT0137
73 in Deck Lastec//072815 6-15
73 in DeckSpindle Housing6
6.8 Spindle Housing
Bolt, 5/16-18 x 5” Hex Head Grade 5
Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5
Washer, 5/16” Split Lock
Plate, Deck Reinforcing
Seal, 2561 Spindle
Collar, Spindle Top
O-Ring, Spindle
Bearing, 6206-2NSE
Housing, Spindle
Pin, 1/8” x 1/2” Roll
Nut, 5/16-18 Nylon Lock Hex
Spacer, Spindle Bearing
O-Ring, 2 7/16" ID x 3/16" Diameter
Washer, 1.50” x 1.185” x 16Ga
Washer, 2.435” x 1.185” x 11Ga
Shaft, Center Blade Spindle
Concerning Nachi Sealed Bearings:
One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubri-cating the bearings forces the motor to work harder.
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full
Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.
Only a small of grease is required to lubricate a bearing in motion.
When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.
When using open bearings, pack the bearing as follows:
REF PART # DESCRIPTION COMMENTS QTY.
043246 Spindle Assembly, Center w/Stiffener Non-saleable item. Parts must be purchased separately.
1
1 F05006-140 Added after serial # 33351208 3
2 F05006-93 3 deleted after serial # 33341208 3
3 F05011-13 3 deleted after serial # 33341208 3
4 034921 1
5 034969 1
6 034951 1
7 062999 Added after serial # 34990809 1
8 P11035 3
9 034945 1
10 F05012-64 1
11 F05010-58 Added after serial # 33351208 3
12 034950 1
13 F04254-45 2
14 034947 1
15 034948 1
16 043245 1
6-16 Lastec//072815 73 in Deck
73 in DeckSpindle Housing 6
LT0024B
73 in Deck Lastec//072815 6-17
73 in DeckTensioner Assembly6
6.9 Tensioner Assembly
Ring, 62mm IR Din #472 Retaining
Bearing, Spindle Top 6305 RS
Pulley, 5” OD Idler, Flat
Pulley, 5” OD Idler
Boss, Idler Pulley Standoff
REF PART # DESCRIPTION COMMENTS QTY.
055428 Idler Assembly, 73” Deck Drive 1
1 F05010-223 Nut, 1/2-13 Flanged Hex Nylock 1
2 062051 Washer, Water Shed Pulley 1
045295 Pulley Assembly, 5” OD Idler, Flat 1
3 F04254-12 2
4 P103 1
5 045296 Serial # 33151108 and later 1
043367 Serial # 33141108 and prior 1
6 045297 1
7 055429 Idler Weldment, 73” Deck Drive 1
8 F05009-66 Bolt, 1/2-13 x 2 3/4” Hex Head Grade 8 1
9 029842 Bushing, 3/4” ID x 1” OD x 1” Oil 2
10 P294 Fitting, 1/4-28 45 Deg Grease 1
11 F05010-222 Nut, 3/8-16 Flanged Hex Nylock 1
12 F05011-104 Washer, 3/8” x 1 1/2” x 1/8” Thk Hardened 1
13 034982 Spring, 1 1/2” OD x 8 1/2” x .195” 1
14 F05010-1 Nut, 3/8-16 Hex 1
15 F05011-4 Washer, 3/8” Split Lock 1
16 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 1
17 019650 Spacer, 1/4” Thk Deck Height 2
6-18 Lastec//072815 73 in Deck
73 in DeckTensioner Assembly 6
LT0031B
73 in Deck Lastec//072815 6-19
73 in DeckDeck 2, Double Pulley Drive Spindle (8/14 and later)6
6.10 Deck 2, Double Pulley Drive Spindle (8/14 and later)
Fitting, 1/4-28 Straight Grease
Bolt, Spindle Single Pulley
Washer, 1/2” Plain Belleville
Key, 1/4” x 1-1/2”
Sheave, Double - D7.0-6.3
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
Spindle Assembly, ZT Cast
Nut, 3/8-16 Flanged Hex Nylon Lock
Blade, 25” x 2-1/2” x 1/4” High Lift
Washer, 2 1/2” x 11/16” x 3/16” Nylon
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
REF PART # DESCRIPTION COMMENTS QTY.
072486 Spindle Assembly, 73” Gas Double Sheave 1
1 P107 1
2 045677 Maximum Torque: 57 ft.lbs 1
3 F05011-97 1
4 028080 1
5 073389 1
1 Replaced 072492 73” Double Sheave (Serial #54410615 and later).
1
6 F05007-78 4
7 067696 See Section 6.6 for parts 1
8 F05010-222 4
9 P107 1
10 029889 1
11 F05011-89 Remove to install Anti-Scalp Blade Disc
1
12 F05009-95 Torque Value: 75 ft.lbs 1
13 048898 Blade Disc, Anti-Scalp Optional part. Remove Item 14 to install Anti-Scalp Blade Disc
1
6-20 Lastec//072815 73 in Deck
73 in DeckDeck 2, Double Pulley Drive Spindle (8/14 and later) 6
LT0149B
73 in Deck Lastec//072815 6-21
73 in DeckDeck 2, Double Pulley Drive Spindle (Prior to 8/14)6
6.11 Deck 2, Double Pulley Drive Spindle (Prior to 8/14)
Fitting, 1/4-28 Straight Grease
Bolt, Spindle Single Pulley
Washer, 1/2” Plain Belleville
Key, 1/4” x 2-1/2”
Sheave, Double 73 Mower
Washer, 1.50” x 1.185” x 16Ga
Washer, 3/8” x 1.5” x 1.01”
Bolt, 3/8-16 x 1 1/2” Carriage Gr5
Plate, Deck Reinforcing
Spindle Assembly, Center w/Stiffener
Nut, 3/8-16 Hex Nylon Lock
Blade, 25” x 2-1/2” x 1/4” Low Lift
Washer, 2 1/2” x 11/16” x 3/16” Nylon
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
REF PART # DESCRIPTION COMMENTS QTY.
055427 Spindle Assembly, 73” Gas Double Sheave 1
1 P107 1
1 P107 replaced P04107 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).
1
2 045677 Maximum Torque: 57 ft.lbs 1
3 F05011-97 1
4 027053 1
5 055395 1
6 034947 1
7 043249 1
8 F05007-85 4
9 044862 2
10 043246 See Section 6.8 for parts 1
11 F05010-10 4
12 P849 1
13 029889 1
14 F05011-89 Remove to install Anti-Scalp Blade Disc
1
15 F05009-95 Torque Value: 75 ft.lbs 1
16 048898 Blade Disc, Anti-Scalp Optional part. Remove Item 14 to install Anti-Scalp Blade Disc
1
6-22 Lastec//072815 73 in Deck
73 in DeckDeck 2, Double Pulley Drive Spindle (Prior to 8/14) 6
LT0034
73 in Deck Lastec//072815 6-23
73 in DeckGrass Chute6
6.12 Grass Chute
Nut, 5/16-18 Nylok Hex
Spring, Deere RH Torsion
Grass Chute, John Deere
Bolt, 5/16-18 x 9” Hex Head Grade 5 Spcl
REF PART # DESCRIPTION COMMENTS QTY
041645 Grass Chute Assembly 1
1 F05010-58 1
2 041714 1
3 041572 1
4 F05006-110 1
6-24 Lastec//072815 73 in Deck
73 in DeckGrass Chute 6
LT0044-2B
73 in Deck Lastec//072815 6-25
73 in DeckRear Anti-scalp Roller (Prior to 8/14)6
6.13 Rear Anti-scalp Roller (Prior to 8/14)
Nut, 3/8-16 Hex Nyloc
Plate, Anti-Scalp Adjusting
Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5
Mount Weldment, Deck Anti-Scalp
Nut, 5/8-11 FlexLoc
Nut, 5/8-11 Jam
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
Bushing, Urethane Pivot
Nut, 5/8-11 Jam Nylon Lock
Wheel, Anti-Scalp, 5 5/8" hole
Bolt, 5/8-11 x 4” Hex Head Grade 5
NOTE: Lubricate all surfaces of the inner bushing (049870) with a water-proof axle grease prior to assembly.
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY
049795 Wheel Assembly, Deck Anti-Scalp 1
1 F05010-10 2
2 063201 1
1 Replaced Deck Lift Link Rod Assembly (046700) on units with serial #34660609 and later. NOTE: 063201 is retrofittable to all units produced to date. 046700 does not work on units with serial #34660609 and later.
1
3 F05007-123 2
4 049794 1
5 F05010-185 1
6 F05010-82 1
7 F05009-35 1
8 049870 1
9 F05010-96 1
10 027013 1
11 F05009-28 1
6-26 Lastec//072815 73 in Deck
73 in DeckRear Anti-scalp Roller (Prior to 8/14) 6
LT0046
73 in Deck Lastec//072815 6-27
Mower//072815 7-1
7
SECTION 7 INDEX
Part Number Index
014419 , Decal, Hot Engine Warning 1-4, 1-6014815, Rod End, 5/16-24 Male LH 2-24, 3-6014818, Spring, Extension 3/8” x 3” 2-2014834, Bearing, w/Snap Ring 5/8” ID 2-24015485, Fitting, 3/8” Barb Tee 3-4018739, Rod End, 3/8-24 Right Hand 2-24, 2-38, 3-6018740, Rod End 3/8-24 Left Hand 2-32, 2-34, 2-38018773, Sheave, BK60 QT 3-6019086, Knob, 1 3/8” x 3/8-24 2-30019086, Knob, 1 3/8” x 3/8-24 2-26019094, Plate, Drive Motor Mount 2-44019298, Hose, Fuel, 1/4” x 8”, 325E98 4-6019359, Bushing, 15mm Split Taper 3-6019552, Decal, Caution Clean Radiator 1-4, 1-6019554 , Decal, Warning, Operational Safety 425D 1-4,
1-6019557, Decal, Articulator Logo Div WM 1-4, 1-6019650, Spacer, 1/4” Thk Deck Height 6-18019696, Cap, Hyd Tank (P631) 4-2, 4-4023541, Bearing, 1” Flanged Mount 2-44024155, Clamp, 1/4" Wire 13/32” Mtg Hole 2-2024155, Clamp, 1/4” Wire 13/32 Mtg Hole 2-40026371, Spring, 1 3/8" x 15.8” x .187” Extension 2-38026382, Angle, Battery Hold Down 4-20026396, Spacer, Clutch 4-10026399, Spacer, Hydro Actuator 3-6026407, Plate Weldment, E-Brake Lock 2-36026409, Pulley, E-Brake 2-36, 3-8, 3-10026412, Rod Weldment, E-Brake Tensioner 2-36026416, Cable E-Brake 2-36026417, Hex Nut, 1-20 Slotted 3-8, 3-10026439, Tire Assembly, 24” x 12-12 Turf Master 3-8,
3-10026440, Rim, 12” x 8 1/2” 8 Spoke 4 1/2” BC 3-8, 3-10026443, Block, Spring Tensioner 2-38026446, Rod Wldmnt, Spring Tensioner 2-38026447, Turnbuckle, Deck Lift 2-38026448, Turnbuckle Assembly, Deck Lift 2-38026470, Belt, BX54 3-6026472, Tensioner Bushing 4-16027006, Spring, 1-1/8" x 7-1/2" x .091 Extension 4-8027009, Guard, Right Hydro Fan 4-14027013, Wheel, Anti-Scalp 5-5/8" hole 2-18027013, Wheel, Anti-Scalp 5-5/8" hole 6-6027013, Wheel, Anti-Scalp, 5-5/8" hole 5-8, 5-28, 6-26027015, Arm Weldment, 2561 Right Control 2-24027016, Arm Weldment, 2561 Left Control 2-24027053, Key, 1/4” x 2 1/2” 5-20027053, Key, 1/4” x 2-1/2” 6-14, 6-22
027056, Plate, E-Brake Pulley Right 3-8027057, Plate, E-brake Pulley Left 3-10027066, Hose, 2561 Oil Drain 3-14, 3-16028072, Fitting, 3/8” NPT Street Tee 3-16028080, Key, 1/4” Square x 1 1/2” Long 5-16, 6-10028080, Key, 1/4” x 1-1/2” 6-20028352, Clamp,1” ID Coated 4-20028390, Grip, Handle 2-24028492, Plug, 3/8” NPT Hex Brass 3-16028493, Fitting, 3/8” NPT F-M-F Tee 3-16028535, Oil, Shell TTF-SB 3-2, 3-4028593, Clamp. 3/4” EMY Coated 3-14, 3-16028601, Decal, Fwd/Rev Motion 1-4, 1-6028603, Decal, Brake Control 1-4, 1-6028818, Grommet, Fuel Tank Fitting 4-2, 4-4029109, Spacer, 3/16” Thk Deck Height 2-44029214, Spacer, 1.00” OD x .41” ID x 1/4” Thk Ny-
lon-Blk 2-36029331, Sheave, BK60 1 1/8” 4-10029354, Block, E-Brake Pivot 2-36029360, Handle Weldment, E-Brake 2-36029397, Rod Weldment, Brake Actuator 2-36029842, Bushing, 3/4” ID x 1” OD x 1” Oil 2-28, 2-44,
5-24, 6-18029889, Washer, 2 1/2” x 11/16” x 3/16” Nylon 5-16,
5-20, 6-10, 6-20, 6-22029889, Washer, 2-1/2” x 11/16” x 3/16” Nylon 6-14034921, Plate, Deck Reinforcing 5-22, 6-16034930, Plate Weldment, Deck Height Adjustment 2-32034945, Housing, Spindle 5-22, 6-16034947, Washer, 1.50 x 1.185 x 16Ga 6-16034947, Washer, 1.50” x 1.185 x 16Ga 6-14034947, Washer, 1.50” x 1.185” x 16Ga 5-18, 5-22,
6-12, 6-22034948, Washer, 2.435 x 1.185 x 11Ga 6-16034948, Washer, 2.435” x 1.185” x 11Ga 5-18, 5-22,
6-12034950, Spacer, Spindle Bearing 5-22, 6-16034951, Collar, Spindle Top 5-22, 6-16034969, Seal, 2561 Spindle 5-22, 6-16034982, Spring, 1 1/2” OD x 8 1/2” x .195” 5-24, 6-18040049, Sheave, Double - 2561 Mower 5-20, 6-14040256, Decal, Warning, Outer Decks -- German 1-6040257, Decal, Warning, Outer Decks -- French 1-6040258, Decal, Warning, Outer Decks -- Italian 1-6040259, Decal, Warning, Outer Decks -- Spanish 1-6040260, Decal, Warning, Outer Decks -- Danish 1-6040267, Decal Kit, European Languages 1-6040311, Clutch, 5.75 Dia x 1-1/8 Bore 12V 4-10
2 Lastec//072815 Index
Part Number Index
040338, Stop Weldment, Clutch 4-10040388, Hose, Fuel 1/4” x 32" 4-6040630, Decal, Hydraulic TTF-SB Oil 3-2, 3-4040635, Black Cap, for 32 oz. Bottle Oil Container 3-2,
3-4040636, Bottle, 32 oz. Container for Oil 3-2, 3-4040637, Spout Cap/ W Red Seal for 32 oz. Container 3-2040637, Spout Cap/ W Red Seal for 32oz Container 3-4040642, Oil,TTF-SB 32 oz. Bottle Hydro 3-2040642, Oil,TTF-SB 32oz Bottle Hydro 3-4040910, Decal, Warning Operate From Seat 1-4, 1-6040911, Decal, Warning Operate With Guards 1-4, 1-6040912 , Decal, Danger, Thrown Objects/Arrow 1-4, 1-6041083, Valve, Two Tank Diverter 3-14, 3-16, 4-6041098-1, Tire, 24” x 12-12 (Tire Only) 3-8, 3-10041180, Hose Assembly, 26” OAL x 1/2” Hyd 3-4041200 , Decal, Fuel Switch 421D 1-4, 1-6041205, Decal, Thrown Objects CE Std 1-7041206, Decal, Caution Symbol CE Std 1-7041209, Decal, Keep Away/Rotating Drive Line CE 1-7041572, Grass Chute, John Deere 5-26, 6-24041645, Grass Chute Assembly 5-2, 5-10, 5-26, 6-2,
6-8, 6-24041669, Socket, 12V Accessory Panel Mount 2-26041714, Spring, Deere RH Torsion 5-26, 6-24042003 , Decal, Warning, Slope 1-4, 1-6042942 , Strap, Rubber Pad Mounting 2-46042943, Plate, Mount Washer 2-46042945 , Pad, Rubber Striping 2-46042947, Striping Kit, Commercial Mower 2-46042949 , Plate Weldment, Hanger Strap 2-46042950, Bracket Wldmnt, Right Striping Kit 2-46042951, Bracket Wldmnt, Left Striping Kit 2-46042985, Plate Weldment, Battery Tray 4-20043225, Decal, Flat World Logo 1-4, 1-6043245, Shaft, Center Blade Spindle 5-22, 6-16043246, Spindle Assembly, Center w/Stiffener 5-20,
5-22, 6-14, 6-16, 6-22043249, Washer, 3/8” x 1.5 x 1.01” 6-14043249, Washer, 3/8” x 1.5” x 1.01” 6-22043251, Bushing, Hex, 3/4” x 3/8” 3-14, 3-16043285, Spring, .72” x 2.75” x .105” MW 2-6043285, Spring, 0.72” x 2.75” x 0.105” MW 2-8, 2-10043320, Brake Assembly, 3377TZ Rear Drum 3-8, 3-10043320, Brake Assembly, Rear Drum 3-12043320-1, Drum, 152.4mm w/Studs 3-8, 3-10, 3-12043320-10, Spring, 152.4 x 25 Brake Return 3-12043320-2, Brake, 152.4 x 25 Cam 3-8, 3-10, 3-12043320-4, Stud, 1/2-20 x 1-1/4 Press In 3-12
043320-5, Arm, 152.4 x 25 Brake Actuator 3-12043320-6, Clip, 152.4 x 25 Retainer 3-12043320-7, Backing Plate, 152.4 x 25 Brake 3-12043320-8, Cam, 152.4 x 25 Brake 3-12043320-9, Shoe, 152.4 x 25 Brake 3-12043367, Pulley, 5” OD Idler 5-24, 6-18043441, Washer, Fuel Tank Retaining 4-2, 4-4043442, Washer, Fuel Tank Double 4-2, 4-4043459, Switch, DPST NO 5A Plunger 2-40043543, Pulley, 5” OD V-Groove Idler 5-8043950, Block, Drive Handle Mount 2-24043952, Arm Pivot Weldment, Right Control 2-24043956, Clamp, Blade Switch Mount 2-26043968, Spacer, Wheel Yoke Bearing 2-20044020, Cover, Handle Lockout Switch Right 2-40044021, Cover, Handle Lockout Switch Left 2-40044588, Switch, Blade Start/Stop 2-26044630, Deck Weldment, 73 Articulating #1 6-2044630, Deck Weldment, 73” Articulating #1 6-4044631, Deck Weldment, 73 Articulating #2 6-2044631, Deck Weldment, 73” Articulating #2 Gas 6-6044632, Deck Weldment, 73 Articulating #3 6-2044632, Deck Weldment, 73” Articulating #3 6-8044683, Hose, Clutch Stop Bushing 4-10044696, Tray Assembly, Commercial Battery 4-20044715, Handle Weldmnt, Throttle 2-26044731, Decal, Control Box Engine Throttle 1-4, 1-6044833, Guard Assembly, AC Series 4-8044835, Guard Weldment, AC Series 4-8044862, Plate, Deck Reinforcing 5-20, 6-14, 6-22045270, Pulley, 5 OD Idler, V Groove 4-14045270, Pulley, 5” OD Idler, V Groove 4-16, 5-8045271, Pulley Assembly, 5” OD Idler, V Groove 4-14,
4-16, 5-8045272, Boss, Idler Pulley Standoff 4-14, 4-16045295 , Pulley Assembly, 5” OD Idler, Flat 5-24045295, Pulley Assembly, 5” OD Idler, Flat 6-18045296, Pulley, 5” OD Idler, Flat 5-24, 6-18045297, Boss, Idler Pulley Standoff 5-8, 5-24, 6-18045320, Hose, Fuel 1/4” x 36” 4-6045328, Hose, Fuel 1/4” x 20” 4-6045519, Decal, Sound Power Level 1-4, 1-6045585, Hose, Fuel 1/4” x 14” 4-6045588, Hose, 1/4” x 16” Fuel 4-6045677, Bolt, Spindle Single Pulley 5-16, 5-20, 6-10,
6-14, 6-20, 6-22045693, Key, Ignition 2-26045897, Plate, Decal Fuel 4-2, 4-4045970, Hose, 3/8” Hyd x 3 1/4” Low Pressure 3-4
Index Lastec//072815 3
Part Number Index
045972, Hose, 3/8” Hyd x 9 1/2” Low Pressure 3-4045972, Hose, 3/8” Hyd x 9 5/8” Low Press. 3-16045973, Tank Assembly, Gasoline Dual Fittings 4-4045986, Wheel Assembly, 13” x 6.5” x 6” 2-20, 2-22045988, Cable, Seat Lanyard 2-2045990, Hose Assembly, 1/2 x 15 1/2” JIC 3-4046122, Switch, Ignition Key 2-26046125, Engine Assembly, 29HP 4-10046126, Engine, Kawasaki 29HP 4-10046129, Hour Meter, Digital LCD 2-26046143, Bushing, Clutch Spacer 4-10046144, Pulley, 5” OD Idler 3-18046236, Handle Weldment, Throttle 2-30046239, Washer, Throttle Friction 2-26, 2-30046240, Clamp, Throttle Conduit 2-30046251, Washer Plate, Throttle Friction 2-26, 2-30046270, Rod Weldment, Cowling Pivot 4-12046273, Washer, 1/4” x 1.47” x 1.01” 5-20046293, Washer, Throttle Friction 2-26, 2-30046477, Wheel Yoke Assembly, 13” Comm 2-8, 2-10,
2-20, 2-40046478, Yoke Weldment, 2561 Front Wheel 2-20046534, Mount, Spring 2-38046552, Housing Cap, Kohler Filter 4-18046553, Air Filter, Primary Element 4-18046554, Air Filter, Inner Element 4-18046556, Hood, Rain 4-18046559, Switch, DPST N/O N/C 2-40046659, Motor, Right Hydro-Gear Drive 3-8046661, Motor, Hydro Gear 3-10046668, Cowling Weldment, 29HP Engine 4-12046719, Radiator Cowling Assembly 4-10, 4-12046739, Spring, Cowling Hinge 4-12046760, Valve, Oil Drain 4-10046761, Fuel Pump 4-6046762, Filter, Fuel 1/4” 4-6046764, Bracket, Fuel Pump Bottom 4-6046765, Fuel Pump Module 4-6046767, Grommet, Fuel Pump Mount 4-6046768, Spacer, Fuel Pump Mount 4-6046769, Strap, Fuel Pump Mount 4-60467701, Fuel Pump Assembly, 29Hp 4-6046771, Hose, Fuel 1/2” x 2-1/4” 4-6046772, Adapter, Fuel Hose Reducer 4-6046780, Housing, Engine Air Filter 4-18046781, Bushing, Clamp Spring 4-18046782, Spring, Filter Clamp 4-18046783, Air Filter Assembly 4-18046783, Air Intake Assembly 4-10
046785, Bracket, Upper 4-18046786, Filter Bracket Weldment 4-18046787, Duct, Upper 4-18046788, Pipe, Intake 4-18046789, Filter Assembly, Engine Air 4-18046800, Key, 5/16” x 1” Woodruff 3-8, 3-10046820, Actuator Kit, RTN Std for Model 2861 3-6047187, Spacer, 5/8” x 1” x 5/8” 2-32047234, Spring, .72 x 2.75 x .095 Dia SS Comp 2-32047234, Spring, .72” x 2.75” x .095” Dia SS Comp 2-40047234, Spring, .72” x 2.75” x .095” Dia. SS Comp 2-34047600, Kit, Hydro-Gear Flow Test 3-2, 3-4047662, Spark Plug, Kawasaki 4-10047663, Oil Filter, Kawasaki 4-10047878, Idler Pivot Weldment 5-24047883, Tube, Vinyl Sight Gage 3-14, 3-16048173, Washer, Wheel Damper 2-6, 2-8, 2-10048174, Block, Wheel Yoke Friction 2-6, 2-8, 2-10048183, Plate, Deck Reinforcing 5-20, 6-14048187, Handle Weldment, Deck Raise 2-34048205, Radiator, Kawasaki 2961 4-10048227, Decal, Hydro Fill Line 1-4, 1-6048272, Belt, 72" Deck Drive 6-2048284, Pump, 12cc Hydrostatic 3-6048285 2, Pump, 12cc Hydrostatic 3-6048393, Mount, Extended Drive Handle 2-24048400, Seal Kit, Hydro-Gear BDP 10-12 3-2, 3-4048451, Pulley Weldment, 9“ Idler 6-6048452, Pulley, 9” B-C Groove Idler 6-6048453, Adapter, Idler Pulley Bore 6-6048468, Rod End, 7/16-20 x 3/8 High Misalign 2-32048468, Rod End, 7/16-20 x 3/8” High Misalign 2-34048504 , Decal, Lastec, Roll Bar 1-4, 1-6048532, Key, 5mm x 5mm x 25mm 3-6048692, Strap, 1U 2-12, 2-14, 2-16, 2-32, 2-34, 2-38048712, Bushing, 1 1/16" Urethane Pivot 2-12, 2-14,
2-16, 2-34, 2-38048712, Bushing, 1-1/16" Urethane Pivot 2-32048890, Plate Assembly, Deck Adjusting 6-6048898, Blade Disc, Anti-Scalp 5-16, 5-20, 6-10, 6-14,
6-20, 6-22048908, Roller Weldment, 3373 Stripping 2-44048910, Frame Weldment, Upgrade Kit 2-44048930, Roller Lift Pivot Wldmnt 2-44048941, Strip, Roller Wiper 2-44048953, Plate, Control Box Access 2-26048988, Fitting, 3/8” NPT - 3/8” Barb 45 Deg 3-16048998, Hose, Fuel 1/4” x 48” 4-6049306, Alarm, 3372 / 3386 2-26
4 Lastec//072815 Index
Part Number Index
049446, Washer, 1.50” OD x .53” ID UHMW 2-4049447, Knob w/Stud, 3/8-16 x 1.50” 2-4049448, Pull Pin, 1/2” 2-4049465, Decal, 73 Inches 1-4, 1-6049466, Decal, Comm. Deck Height Adjustment 1-4,
1-6049484, Bar Weldment, Pull 2-42049488, Bar Assembly, Pull 2-42049490, Deck Weldment, 61” Articulating #3 5-10049490, Deck Wldmnt, 61 Articulating #3 5-2049510, Bushing, Rubber Pivot 2-18, 5-8049512, Deck Weldment, 61” Center 5-8049512, Deck Wldmnt, 61 Center 5-2049526, Deck Assembly, 61” Articulating #3 5-10049532, Deck Weldment, 61 Articulatin #1 5-6049532, Deck Wldmnt, 61 Articulatin #1 5-2049537, Arm, E-Brake Link 2-36049541, Rod Assembly, Rear Deck Lift 2-38049542, Rod Wldmnt, Rear Deck Lift 2-38049544, Rod Assembly, Front Deck Lift 2-34049545, Rod Weldment, Front Deck Lift 2-32, 2-34049550, Handle Assembly, E-Brake 2-36049564, Mount Weldment, Engine 4-14049569, Arm Weldment, Hydro Tensioner 3-18049570, Idler Assembly, Hydro Drive 3-18049571, Rod, Polyurethane Spring 3-18049589, Pan Weldment, Seat 2-2049590, Seat Assembly, Complete Gas 2-2049596, Tank Weldment, 2861AGC Hyd 3-16049599, Box, Battery Modified 4-20049619, Decal, 2961AGC Articulatot Large 1-4, 1-6049620, Decal, 2973AGC Articulator Large 1-4, 1-6049668, Wheel Yoke Assembly, 13” Comm Right 2-8,
2-10, 2-20049700, Battery Assembly, 33HP 4-20049701, Boss Weldment, Rubber Spring Tensioner 4-16049702, Plate Weldment, Deck Drive Idler 4-16049705, Idler Assembly, Deck Drive 4-14, 4-16049706, Arm Assembly, Right Control Handle 2-24049707, Arm Assembly, Left Control Handle 2-24049710, Rocker Weldment, Left 2-6049717, Rocker Weldment, Right 2-6049720, Lift Weldment, Left Deck 2-16049725, Lift Weldment, Deck Tab 2-12, 2-14, 2-16049726, Lift Assembly, Left Rocker Deck 2-10, 2-16049728, Pedal Assembly, Control 2-28049730, Pedal Weldment, Foot Control 2-280497361, Frame Weldment, Comm. ROPS Lower 2-4049736-11, Frame Weldment, Comm. ROPS Lower 2-4
049738, Rod Weldment, Foot Control 2-28049739, Rod Assembly, Foot Control 2-28049740, Rocker Wheel Assembly, Left 2-8, 2-10, 2-18049741, Weldment, Left Rocker Wheel Pivot 2-18049744, Weldment, Right Rocker Wheel Pivot 2-18049745, Rocker Wheel Assembly, Right 2-8, 2-10, 2-18049747, Decal, Comm Mower Control Panel Gas 1-4,
1-6, 2-26049769, Channel, Battery Box Spacer 4-20049781, Baffle, Outside Rear Bolt-On 5-6, 5-10049784, Baffle, Outside Rear Bolt-On 5-8049787, Turnbuckle, Deck Lift Link 2-32, 2-34049788, Rod Assembly, Deck Lift Link 2-34049789, Lift Weldment, Right Deck 2-14049790, Lift Assembly, Right Rocker Deck 2-8, 2-10,
2-14049791, Cover, Left Rocker 2-6049792, Cover, Right Rocker 2-6049794, Mount Wldmnt, Deck Anti-Scalp 5-28, 6-26049795, Wheel Assembly, Deck Anti-Scalp 5-28, 6-26049796, ROPS Assembly, 2861 Folding 2-4049797, Idler Assembly, Deck Drive 5-24049809, Fitting,1/4” Barb 90 Tank w/ 3" Long Tube 4-4049809, Fitting,1/4” Barb 90 Tank w/3" Long Tube 4-2049831, Frame Weldment, ROPS 2-40498361, Pump Assembly, 12cc Left Hydro 3-6049837, Pump Assembly, 12cc Right Hydro 3-6049838, Turnbuckle Assembly, Hydro 3-6049839, Rod, Hydro Control Link 3-6049843, Link Assembly, 3/8 Suspension 2-16049843, Link Assembly, 3/8” Suspension 2-12, 2-14049847, Belt, B-134 Custom 4-10049855, Belt, B-128 Deck Drive 5-2049856, Cable Assembly, 2861 Throttle 2-26, 2-30049857, Hose, 3/8” Hyd x 12” Low Press. 3-16049857, Hose, 3/8” Hyd x 12” Low Pressure 3-4049866, Baffle Weldment, #1 Deck Mulching 5-14049868, Spacer, .53” ID x 1 1/4” OD x 1 1/4” Lng 5-8049869, Spring, Urethane 4-16049870, Bushing, Urethane Pivot 2-18, 2-40, 5-8, 5-28,
6-6, 6-26049873, Baffle Weldment, #3 Deck Mulching 5-12049877, Baffle Weldment, #2 Deck Mulching 5-14049891, Hose, 3/8” Low Pressure 28” 3-14, 3-16049892, Spindle Assembly, 2861AGC Double Sheave
5-20049893, Washer, 3 1/2” OD Wave 2-6049893, Washer, 3-1/2” OD Wave 2-8, 2-10049894, Link, Front Deck Lift 5-8, 6-6
Index Lastec//072815 5
Part Number Index
049895, Bracket, Right Seat Latch 4-20049896, Bracket, Left Seat Latch 4-20049908, Gage, Fuel Indicator 4-4049909, Grommet, Fuel gage 4-4049928, Kit, Hydro Oil Repl 5 Gal 3372 3-2, 3-4049929, Kit, Hydro Oil Repl 2 1/2 Gal 3372 3-2, 3-4049930, Decal, Belt Routing Diagram 1-4, 1-6049931, Decal, 61 Inches 1-4, 1-6049960, Baffle Weldment, #2 Deck Rear Discharge 5-12049961, Baffle Assembly, #2 Deck Rear Discharge 5-12049962, Baffle Assembly, #2 Deck Mulching 5-14049963, Baffle Assembly, #3 Deck Mulching 5-12049964, Baffle Assembly, #1 Deck Mulching 5-14049965, Wheel/Motor Assembly, 2861 Right Rear 3-8049966, Wheel/Motor Assembly, 2861 Left Rear 3-10049984, Sure Grip, Foot Pan 2-40049997, Baffle Kit, Rear Discharge 5-12049998, Baffle Kit, Mulching 61AGC 5-14050436, Relay, 40A 12VDC Automotive 4-14050477-1, Light Assy, LED Red 3/16” FI Male Quicks
2-26052025, Seat Delay Assembly, LasTec Mowers 2-2055083, Rocker Weldment, Left 2-8055084, Rocker Weldment, Right 2-8055085, Rocker Assembly, Left 2-8055086, Rocker Assembly, Right 2-8055151, Plate, E-Brake Cable Retaining 3-8, 3-10055177, Plate, E-Brake Pulley Right 3-8055178, Plate, E-brake Pulley Left 3-10055192, Bolt Weldment, Height Adjust Eye 6-6055384, Rocker Weldment, 73” Right 2-6055384, Rocker Weldment, Right 2-10055385, Rocker Weldment, 73” Left 2-6055385, Rocker Weldment, Left 2-10055386, Rocker Assembly, 73” Right 2-10055387, Rocker Assembly, 73” Left 2-10055390, Deck Assembly, 73” Articulating #1 6-4055392, Deck Assembly, 73” Articulating #3 6-8055395, Sheave, Double 73 Mower 6-22055405, Spacer, 73” Deck 1/2ID x 1-3/8 6-6055424, Baffle Weldmnt, 73” #2 Deck 6-6055427, Spindle Assembly, 73” Gas Double Sheave 6-22055428, Idler Assembly, 73” Deck Drive 6-18055429, Idler Weldment, 73” Deck Drive 6-18055438, Tank Assembly, Fuel Dual Fitting 4-4055442, Washer, 1/2” Delrin 2-38055444, Spindle Assembly, 73” Double Sheave 6-14055445, Belt, B-130 Custom 4-10055446, Tube, Fuel Pick Up 4-2, 4-4
055452, Kit, Rear Discharge Chute 5-12055464, Plate Weldment, Deck Height Adjust 2-34055481, Control Box Weldmnt, AC Gas w/ Throttle 2-26055483, Lift Weldment, Left Deck 2-12055486, Rocker Weldment, Left 2-8055803, Cover, 61A Deck #1 5-4, 5-6, 6-4055804, Cover, 61A Deck #3 5-10, 6-8055831, Lift Assembly, Left Rocker Deck 2-8, 2-12055834, Deck Assembly, 61” Articulating #1 5-4055835, Deck Weldment, 61” Articulating #1 5-4055835, Deck Weldmnt, 61 Articulating #1 5-2055841, Sure Grip, 1 1/2” Bar 2-40055843, Decal Kit, 2961AGC 1-4, 1-6055847, Decal Kit, 2973AGC 1-4, 1-6055890, Baffle Assembly, #3 Deck Mulching 73” 6-8055891, Baffle Weldment, #3 Deck Mulching 73” 6-8055895, Hose, Fuel 1/2” x 20” Long 4-10055896, Hose, Fuel 5/16” x 42” Lng 4-6055897, Tank Assembly, 29HP Hyd 3-16055924, Hose, Fuel 5/16” x 15” Lng 4-6056241, Pedal Kit, AGC Foot 2-28056244, Guard, Left Hydro Fan 4-14056250, Control Box Assembly, Gas w/Buzzer 2-26056449, Rod, Hydro Control Link 2-24056450, Turnbuckle Assembly, Hydro Diesel 2-24056547, ECU, Kawasaki 4-10056591, Decal, 18 PSI 1-4, 1-6057002, Fan, Kawasaki Cooling-29HP 4-10057501, Gauge, Kawasaki Air Filter Minder 4-18057507, Muffler, 29HP Kawasaki 49069-2356-Y 4-10059776, Capture Weldment, Clutch Stop 4-10060169, Knob, 3/8” Bore Oval/Tapered Plastic 4-8061807, Hose Clamp, Dixon Worm Gear HSS6 3-4, 3-16061953, Boot, Vinyl Cable 2-26061954, Grommet, Cable Wiper 2-26061974, Clamp, Cable 2-26062051, Washer, Water Shed Pulley 5-8, 5-24, 6-18062404, Decal, AGC/ADC Hydro 1-4, 1-6062425, Decal, Relays for 055700-055846 1-4, 1-6062429, Decal, Lastec Made in USA 1-4, 1-6062950, Adjusting Weldment, Deck 6-6062999, O-Ring, Spindle 5-22, 6-16063201, Plate, Anti-Scalp Adjusting 5-28, 6-26063206, Cable Assembly, Gas Throttle 2-26063252, Cap, Gas Fuel Tank Vented 4-4063265, Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra 5-16,
5-20063266, Blade, 25” x 2 1/2” x 1/8” Low-Lift Ultra 6-10,
6-14
6 Lastec//072815 Index
Part Number Index
063377, Upgrade Kit, 61-73 AGC Roller 2-44063378, Pivot Collar Mount Weldment 61-73AGC 2-44063382, Plate, Clamp Pivot Collar Mount 2-44063383, Arm, Roller Lift Link 61-73 AGC 2-44063384, Spacer, Lift Link Arm 61-73 AGC 2-44063869, Plate, Roller Mount 2-44063870, Tube, Roller Mount Spacer 2-44064468, Hood Assembly, 29HP Kawasaki CE 1-9064500, Nut Assembly, 3/8-16 Cover Retaining 1-9064521, Kit, 2961/73 CE Hardware 1-9064653, Vent, Remote w/Valve 4-2064654, Grommet, Remote Vent 4-2064658, Fitting, 1/4” Tee Barb 4-6067065, Decal Kit, CE Deck 1-6067359, Tank Assembly, Gasoline Dual Fittings 4-2067363, Cap, Gas Fuel Tank Ratchet 350 4-2067364, Tube, 3.5" Vapor Neck 4-2067370, Carbon Canister, 9 Gal 4-6067381, Battery, Group 26 w/Handle 4-20067686, Spacer, Spindle Bearing Housing 5-18, 6-12067687, Shaft, Blade Spindle ZT Cast 5-18, 6-12067688, Sheave, Double - Mower Deck 5-16, 6-10067694, Spindle Assembly, ZT 25” D6.3-6.3 6-4, 6-8,
6-10067695, Spindle Assembly, ZT 21” D6.3-6.3 5-4, 5-8,
5-10, 5-16067696, Spindle Assembly, Center w/Stiffener 5-18,
6-12067696, Spindle Assembly, ZT Cast 5-16, 6-10, 6-20067973, Hose Clamp, 3/16” Spring 4-6067999, Spindle Housing, ZT- Common Core 5-18, 6-12071864, Fitting, 8 ORFS - 10 STOR 90 3-8, 3-10072486, Spindle Assembly, 73” Gas Double Sheave 6-20072486, Spindle Assy, 73” Gas Double Sheave 6-6072497, Spacer, 1 OD x .65 ID x .53 Long 5-8072497, Spacer, 1 OD x .65 ID x .53 Long 6-6072505, Hose Clamp, 3/16” Spring 3-14072506, Hose Clamp, 1/4” Spring 4-6072507, Hose Clamp, 5/16” Spring 4-6072511, Spacer, Bearing Housing 5-18, 6-12072539, Fitting, 6 ORFS - 6 PushLok 90 3-14072541, Fitting, 6 ORFS - 6 PushLok ST 3-14072556, Fitting, 6 ORFS - 6 MPT 90 3-14072560, Fitting, 8 ORFS - 8 STOR LL 90 3-6072582, Tank Weldment, 28AGC Hyd 3-14072584, Fitting, 6 ORFS - 6 MPT 45 3-14072585, Fitting, 6 ORFS - 6 STOR 90 3-6072587, Hose Assembly, 1/2” HP x 30” ORFS 8 ST 3-20725871, Hose Assembly, 1/2HP x 30In ORFS 8 ST 3-6
072588, Hose Clamp, 1/2” Spring 4-6, 4-10072589, Screen, Radiator Kawasaki 29Hp 4-10072591, Tank Assembly, 29AGC Hyd 3-14072594, Hose, 3/8” Hyd x 4” Low Press. 3-14072595, Hose, 3/8” Hyd x 10” Low Press. 3-14072596, Hose, 3/8” Hyd x 14” Low Press. 3-14072597, Hose Assembly, 3/8” LP x 6” ORFS 6 90 3-2,
3-14072598, Hose Assembly, 3/8” LP x 12” ORFS 6 ST 3-14072598, Hose Assembly, 3/8” LPx12” ORFS 6 ST 3-2072599, Hose Assembly, 3/8” LP x 16.5” ORFS 6 45 3-2072599, Hose Assembly, 3/8” LPx16.5” ORFS 6 45 3-14072600, Fitting, 6 ORFS - 6 PushLok 45 3-14072684, Clutch Assembly, 5.75 Pitch 1 1/8 Bore 12V
4-10072735, Gauge, Fuel Indicator Sealed 4-2072736, Grommet, Fuel Gauge Sealed 4-2072858, Tank Assembly, 7 Gallon Gas Dual Fitting 4-2073357, Housing Cap Dirt Ejector, Kohler Filter 4-18073389, Sheave, Double - D7.0-6.3 6-20085614, Grommet, Rubber 2 1/2” Dia 4-2, 4-4EE20482, Light, Red 12 Volt .187 Tabs 2-26FF04203-6, Rivet, 3/16” Dia x 3/8-1/2” Grip Range Pop
1-9F04254-12, Ring, 62mm IR Din #472 Retaining 4-14,
4-16, 5-8, 5-24, 6-18F04254-4, Ring, 1.575” ID 3000-156 Retaining 6-6F04254-45, O-Ring, 2 7/16" ID x 3/16" Diameter 5-22F04254-45, O-Ring, 2-7/16"ID x 3/16" Diameter 6-16F04254-46, Ring, 3/4” External - External 2-28, 5-8, 6-6F04254-46, Ring, 3/4” External Retaining 2-44F05004-1, Screw, 10-24 x 1/2” Sl Hex Machine 2-40F05004-123, Bolt, 3/8-16 x 3 1/2” Hex Head Gr5 2-32F05004-123, Bolt, 3/8-16 x 3 1/2” Hex Head Grade 5
2-34F05004-126, Screw, 10-24 x 3/4” Phillips PH Machine
2-40F05004-18, Screw, 10-24 x 5/8” Unsl Indent HH Ma-
chine 4-2, 4-4, 4-14F05004-19, Screw, 10-24 x 1 1/4” Unsl Ind HH Machine
4-6F05004-237, Screw, M8 x 1.25 x 60 Hex Washer Hd w/o
Serr 4-18F05004-238, Screw, M8 x 1.25 x 14 Hex Washer Hd w/o
Serr 4-18F05004-285, Screw, 10-24 x 5/8” SBHC SS 4-2F05004-35, Screw, 10-24 x 1/2” SBHC 4-8, 4-12
Index Lastec//072815 7
Part Number Index
F05004-48, Bolt, M10-1.5 x 25mm Hex Head FT 8.84-10
F05004-93, Screw, 6-32 x 3/4” SBHC SS 2-26F05005-101, Bolt, 1/4-20 x 1” Hex Head Grade 5 3-6,
4-12F05005-105, Screw, 1/4-28 x 1/4” BO SH Cup Pt Set
2-24F05005-105, Screw, 1/4-28 x 1/4” BO Socket Head Pt
Set 2-12, 2-14, 2-16F05005-116, Bolt, 1/4-20 x 1 1/4” Hex Head Grade 5
4-20F05005-123, Bolt, 1/4-20 x 3/4” Hex Head Grade 5 4-12F05005-137, Bolt, 1/4-20 x 5/8” Hex Head Grade 5 2-26F05005-68, Bolt, 1/4-20 x 1 3/4” Hex Head Grade 5 4-6F05005-79, Bolt, 1/4-20 x 1/2” Hex Head Cap 2-6F05005-79, Bolt, 1/4-20 x 1/2” HHC 3-14, 3-16F05006-101, Bolt, 5/16-18 x 3/4” Hex Head
W/Flat&Lock Washer 4-14F05006-102, Bolt, 5/16-18 x 3/4” Hex Head Grade 5 2-2,
2-40, 4-6F05006-102, Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc
2-26, 3-8, 3-10, 4-20, 5-8F05006-110, Bolt, 5/16-18x9 HH Gr5 Spcl 5-26, 6-24F05006-117, Bolt, 5/16-18 x 3/4” SHC SS 3-8, 3-10F05006-123, Bolt, 5/16-18 x 8-1/2” Hex Head Grade 5
4-20F05006-140, Bolt, 5/16-18 x 5” Hex Head Grade 5 5-22,
6-16F05006-27, Bolt, 5/16-18 x “1 Hex Head Grade 5 4-10F05006-27, Bolt, 5/16-18 x 1” Hex Head Grade 5 2-2,
2-26, 2-44, 4-20, 5-6, 5-8, 5-10
F05006-81, Bolt, 5/16-18 x 1 3/4” FT Hex Head Gr5 2-32F05006-93, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread
Gr5 5-22F05006-93, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread
Grade 5 5-10F05006-93, Bolt, 5/16-18x1 1/4 HH FT Gr5 6-16F05007-109, Bolt, 3/8-16 x 4 3/4” Hex H ead Grade 5
2-38F05007-118, Bolt, 3/8-16 x 3/4” Hex Head Grade 5 2-44F05007-119, Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5
2-32, 2-34F05007-123, Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5
2-24, 3-8, 3-10, 4-10F05007-123, Bolt, 3/8-16x1 1/4 HH Gr5 5-28, 6-26F05007-124, Bolt, 3/8-16 x 2” Hex Head Grade 5 3-10F05007-125, Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5
2-12, 2-14, 2-16, 2-40
F05007-126, Bolt, 3/8-16 x 4” Hex Head Grade 5 2-4, 2-12, 2-14, 2-16, 2-32, 2-34
F05007-127, Bolt, 3/8-16 x 1 1/4” Carriage Grade 5 2-30F05007-127, Bolt, 3/8-16 x 1 1/4” Carriage Grade 5 2-26F05007-129, Bolt, 3/8-16 x 1 3/4” FT Grade 5 4-8F05007-136, Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5
2-32, 2-34, 2-38, 4-14F05007-165, Bolt, 3/8-16 x 1” Carriage Grade 5 5-12,
5-14, 6-8F05007-165, Bolt, 3/8-16 x 1” Carriage, Zinc Grade 5
5-8, 6-6F05007-206, Bolt, 3/8-16 x 2 3/4” Hex Head Grade 5 2-4F05007-214, Screw, 3/8-16 x 2” SHC 4-8F05007-244, Bolt, 3/8-16 x 4 1/2” Hex Head 316 SS 2-2F05007-58, Screw, 3/8-16 x 2” BO SHC 4-8F05007-73, Bolt, 3/8-16 x 3” Hex Head Gr5 2-32F05007-73, Bolt, 3/8-16 x 3” Hex Head Grade 5 2-34F05007-78 , Bolt, 3/8-16x1 1/2 HH Gr5 2-46F05007-78, Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 2-36,
2-38, 3-6, 5-16, 5-24, 6-6, 6-10, 6-18, 6-20
F05007-85, Bolt, 3/8-16 x 1 1/2” Carriage Gr5 6-14, 6-22
F05007-85, Bolt, 3/8-16 x 1 1/2” Carriage Grade 5 5-12, 5-20, 6-8
F05007-87, Bolt, 3/8-16 x 1” Hex Head Grade 5 3-14, 3-16
F05007-87, Bolt, 3/8-16 x 1” Hex Head Grade 5 2-24F05008-10, Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 3-18,
4-14, 4-16, 5-24F05008-106, Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade
5 2-6F05008-106, Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade
5 2-8, 2-10F05008-143, Bolt, 1/2-13 x 3 3/4” Hex Head Grade 5
2-44F05008-159, Bolt, 1/2-13 x 6 1/2” Hex Head Grade 5
2-44F05008-23, Bolt, 1/2-13 x 3” Hex Head Grade 5 2-4, 2-8,
2-10, 5-8F05008-23, Bolt, 1/2-13 x 3” Hex Head Grade 5 Zinc 2-6F05008-28, Bolt, 1/2-13 x 5 1/2” Hex Head Grade 5 3-8,
3-10F05008-35, Bolt, 1/2-13 x 4 1/2” Hex Head Cap Grade 5
2-8, 2-10F05008-35, Bolt, 1/2-13 x 4-1/2” Hex Head Gr5 2-6F05008-37 , Bolt, 1/2-13x1 1/4 HH Gr5 2-46F05008-37, Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 2-12,
2-14, 2-16, 2-44
8 Lastec//072815 Index
Part Number Index
F05008-61, Bolt, 1/2-13 x 3 1/2” Hex Head Grade 5 6-6F05008-96, Bolt, 5/16-18 x 1 1/2” Hex Head Grade 5
2-24F05009-10, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 2-6F05009-10, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 2-8,
2-10, 5-8F05009-10, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 6-6F05009-108, Bolt, 3/4-10 x 9” Hex Head Grade 5 2-20F05009-111, Bolt, 5/8” x 1/2” Shoulder 2-44F05009-20, Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5 5-4,
5-6, 5-10, 6-4, 6-8F05009-28, Bolt, 5/8-11x4 Gr5 HH 5-28, 6-26F05009-35, Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5 2-42,
6-4, 6-8F05009-35, Bolt, 5/8-11x2 3/4 HH Gr5 5-28, 6-26F05009-37, Bolt, 5/8-11 x 3 Hex Head Grade 5 2-8, 2-10F05009-37, Bolt, 5/8-11 x 3” Hex Head Grade 5 2-44F05009-37, Bolt, 5/8-11 X 3” Hex Head Grade 5 Zinc 2-6F05009-66, Bolt, 1/2-13 x 2 3/4” Hex Head Grade 8 6-18F05009-70, Bolt, 5/16-18 x 1 3/4” Hex Head 3-6F05009-95, Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5 5-16,
5-20, 6-10, 6-14, 6-20, 6-22F05010-1, Nut, 3/8-16 Hex 2-24, 5-24, 6-6, 6-18F05010-10, Nut, 3/8-16 Hex Nyl Lock 2-30F05010-10, Nut, 3/8-16 Hex Nyl Lock 2-12, 2-14, 2-16F05010-10, Nut, 3/8-16 Hex Nyloc 2-4, 2-12, 2-14,
2-16, 2-26, 2-32, 2-34, 2-36, 2-38, 2-40, 3-6, 4-8, 4-14, 5-6, 5-10, 5-20, 5-28, 6-14, 6-26
F05010-10, Nut, 3/8-16 Hex Nylon Lock 6-6, 6-22F05010-119, Nut, 5/16-24 Jam LH 2-24, 3-6F05010-121, Nut, 5/16-18 Nylon Locking Jam 3-8, 3-10F05010-123, Nut, 3/8-24 Free 2-24, 2-28, 3-6F05010-124, Nut, 3/8-16 Half Nyloc 2-24, 2-32, 2-34,
3-8, 3-10, 4-10F05010-124, Nut, 3/8-16 Half Nylock 3-14, 3-16F05010-14, Nut, #10-24 Keps 2-40, 4-14F05010-160, Nut, 10-24 Hex Nylock 4-2, 4-6, 4-8, 4-12F05010-166, Nut, 3/8-24 LH Jam 2-32, 2-34, 2-38F05010-17, Nut, 5/16-18 Hex 2-26, 2-32F05010-177, Nut, 3/4-10 Stover Swaged 2-20F05010-185, Nut, 5/8-11 FlexLoc 2-8, 2-10, 5-4, 5-6,
5-10, 5-28, 6-4, 6-8, 6-26F05010-185, Nut, 5/8-11 Flexloc 2-6F05010-185, Nut, 5/8-11 Flexlock 2-44F05010-201, Nut, 1/2-13 Hi-Crown Acorn Cap Plated
2-8, 2-10F05010-22, Nut, 3/8-24 UNF Hex Jam 2-38
F05010-220, Nut, 1/4-20 Flanged Hex Nylock 4-6F05010-221, Nut, 5/16-18 Flanged Hex Nylock 4-6F05010-222, Nut, 3/8-16 Flanged Hex Nyl Lock 5-12F05010-222, Nut, 3/8-16 Flanged Hex Nyloc 5-4, 5-16,
5-24, 6-10F05010-222, Nut, 3/8-16 Flanged Hex Nylock 5-14, 6-4,
6-6, 6-8, 6-18F05010-222, Nut, 3/8-16 Flanged Hex Nylon Lock 5-8,
6-20F05010-223, Nut, 1/2-13 Flanged Hex Nylock 6-6, 6-18F05010-223, Nut, 1/2-13 Flanged Nylon Hex Lock 5-24F05010-224, Nut, 5/8-11 Flanged Hex Nylock 5-8F05010-224, Nut, 5/8-11 Flanged Hex Nylock 6-6F05010-234, Nut, 3/8-16 Hex Half Nylon Lock 316 SS
2-2F05010-29, Nut, 3/8-16 Jam 6-6F05010-34, Nut, 5/8-11 Nyl Lock 2-18F05010-35, Nut, 1/2-13 Hex 4-16F05010-38, Nut, 7/16-20 Jam 2-32, 2-34F05010-58, Nut, 5/16-18 Nylok Hex 2-2, 2-24, 3-6,
4-10, 5-6, 5-10, 5-26, 6-16, 6-24
F05010-58, Nut, 5/16-18 Nylon Lock Hex 2-40, 5-8, 5-22
F05010-59, Nut, #6-32 Keps 2-26F05010-69, Nut, 1/4-20 Nylock 4-20F05010-69, Nut, 1/4-20 Nylon Lock 4-12F05010-8, Nut, 1/2-13 Hex Nylon Lock 2-44F05010-8, Nut, 1/2-13 Nyl Hex Lock 2-6F05010-8, Nut, 1/2-13 Nyl Hex Lock 2-6F05010-8, Nut, 1/2-13 Nyl Hex Lock 2-8, 2-10, 2-36,
3-8, 3-10, 4-14F05010-8, Nut, 1/2-13 Nylon Hex Lock 2-4, 2-8, 3-18,
4-16, 5-8F05010-82, Nut, 5/8-11 Jam 5-28, 6-26F05010-9, Nut, 1/4-20 Keps 4-12F05010-96, Nut, 5/8-11 Jam Nyl Lock 5-28, 6-26F05011-101, Washer, 1/2” SAE Flat Gr5-8 (Thru Hard)
2-38F05011-101, Washer, 1/2” SAE Flat Grade 5-8 (Thru
Hard) 3-8, 3-10F05011-104, Washer, 3/8 x 1-1/2 x 1/8 Thick Hardened
5-24F05011-104, Washer, 3/8” x 1 1/2” x 1/8” Thk Hardened
6-18F05011-104, Washer, 3/8” x 1-1/2” x 1/8” Thk Hardened
6-6F05011-107, Washer, .625 ID x 1.312 OD x .050 Thick
Nylon 2-44
Index Lastec//072815 9
Part Number Index
F05011-11, Washer, 1/4” SAE Flat 2-6F05011-11, Washer, 1/4” SAE Flat 4-20F05011-110, Washer, 3/8” Push Nut 2-28F05011-111, Washer, 20mm Bellville 2-28F05011-115, Washer, 1” ID .03 SS Shim 3-8, 3-10F05011-116, Washer, 1” ID .06 SS Shim 3-8, 3-10F05011-117, Washer, 7/16” Nord-Lock 4-10F05011-13, Washer, 5/16 Split Lock 4-6, 4-20, 6-16F05011-13, Washer, 5/16” Split Lock 2-26, 2-44, 3-8,
3-10, 4-20, 5-8, 5-22F05011-14, Washer, 1/4” Split Lock 2-6, 3-14, 3-16F05011-14, Washer, 1/4” Split Lock 2-26, 3-6F05011-16, Washer, 5/16” Standard Flat 3-8, 3-10F05011-17, Washer, 5/16 SAE Flat 4-10F05011-17, Washer, 5/16” SAE Flat 5-8, 5-10F05011-17, Washer, 5/16” SAE Flat 2-26, 2-40, 2-44,
4-20, 5-6F05011-18, Washer, #10 SAE Flat 4-6, 4-14F05011-2, Washer, 1/2” SAE Flat 2-12, 2-14, 2-16,
2-36, 3-18, 4-16F05011-20, Washer, #10 Split Lock 2-26, 2-40, 4-2, 4-4F05011-27, Washer, 5/8” Split Lock 5-20, 6-14F05011-3, Washer, 3/8” Flat SAE 3-14, 3-16F05011-3, Washer, 3/8” Flat SAE 2-4, 2-12, 2-14, 2-16,
2-24, 2-26, 2-28, 2-32, 2-34, 2-38, 3-6, 3-8, 3-10, 4-10, 4-12, 4-14, 5-6
F05011-3, Washer, 3/8” SAE Flat 2-30F05011-3, Washer, 3/8” SAE Flat 2-44F05011-33, Washer, 5/16 Star ET 4-10F05011-4 , Washer, 3/8 Split Lock 2-46F05011-4, Washer, 3/8” Split Lock 2-24, 2-44, 4-10,
6-18F05011-40, Washer, 5/8” Standard Flat 2-42F05011-5, Washer, 5/8” SAE Flat 2-6F05011-5, Washer, 5/8” SAE Flat 2-8, 2-10, 2-18, 4-16F05011-50, Washer, 5/16” x 1 1/4” Fender 2-2F05011-62, Washer, 3/4” SAE Flat 2-20F05011-68, Washer, 1/2” Standard Flat Zn 4-14, 4-16F05011-77, Washer, 3/4” AN Yel/Cad 2-28, 2-44, 5-8,
6-6F05011-88, Washer, 10mm Split Lock 4-10F05011-89, Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat
5-20F05011-89, Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat
Znc 5-16, 6-10, 6-20, 6-22F05011-89, Washer,2 1/2” OD x 5/8” ID x 3/16” Std Flat
Znc 6-14F05011-9 , Washer, 1/2 Split Lock 2-46
F05011-9, Washer, 1/2” Split Lock 2-44, 5-8F05011-97, Washer, 1/2” Plain Belleville 2-36, 5-16,
5-20, 6-10, 6-14, 6-20, 6-22F05012-1, Pin, 1/8” x 1” Cotter 2-36F05012-11, Pin, 3/16” x 1” Roll 2-36F05012-115, Pin, 3/4” Clevis Retaining 2-36, 4-16F05012-21, Pin, 3/16” x 1” Cotter 4-16F05012-3, Pin, 1/8” x 3/4” Cotter 2-28F05012-49, Pin, 1/8” x 1 1/2” Cotter 2-20, 3-8, 3-10F05012-64, Pin, 1/8” x 1/2” Roll 5-22F05012-64, Pin, 1/8x1/2 Roll 6-16F05012-79, Pin, 5/32” x 1 1/2” Cotter 2-20F05012-8, Pin, 3/8” x 1 3/32” Clevis 2-38F05015-17, Bolt, #10-24 x 1/2” PH 2-30F05015-17, Bolt, #10-24 x 1/2” Phillips PH 2-26F0510-185, Nut, 5/8-11 FlexLoc 2-42F412, Screw, Seat Switch 2-2F81003-29, Bolt, M10-1.5 x 55mm Hex Head Full
Thread G5 4-10IIS-0192 , Instr. Sheet, 61 Deck Striping Kit 2-46IS-0218, Instruction Sheet, 056241 Kit 2-28IS-0277, Instruction Sheet, 61-73 Roller Assembly 2-44IS-0307, Instruction Sheet, 2961/73 CE Hardware Kit
1-9NN/A, Bolt, 3/8-16 x 7” Hex Head Grade 5 2-12, 2-14,
2-16N/A, Bushing, 3/8” Polyurethane Suspension 2-12, 2-14,
2-16N/A, Spacer, 3/8” Suspension 2-12, 2-14, 2-16N/A, Washer, 3/8” Suspension 2-12, 2-14, 2-16PP04107, Fitting, 3/16” x 3/16” Straight Grease 5-20P04211, Knob, 5/8-18 Ball 2-32, 2-34, 2-36, 2-44P04332, Cap, 3/8” Pipe Galvanize 4-10P04332, Cap, 3/8” Pipe Galvanized 3-14, 3-16P04646, Nut, 1/2-20 Lug 3-8, 3-10P05035, Collar, 5/8” ID Lock 2-24P06030-2, Bearing, 6203-2NSL 17mm SRI-2 ABEC-1
6-6P06104, Foot, Rubber 4-8, 4-12P07584, Clamp, 1/2” EMT Coated 4-14P09895, Clamp, 2 1/2” Worm 4-18P103, Bearing, Spindle Top 6305 RS 4-14, 4-16, 5-8,
5-24, 6-18P105, O-Ring, 2 1/2” ID x 2 3/4” OD 5-18, 6-12P107, Blade, 25” x 2-1/2” x 1/4” High Lift 6-20P107, Fitting, 1/4-28 Straight Grease 2-6
10 Lastec//072815 Index
Part Number Index
P107, Fitting, 1/4-28 Straight Grease 2-8, 2-10, 2-28, 2-40, 2-44, 5-16, 6-10, 6-14, 6-20, 6-22
P110, Pin, 3/8” x 1 5/16” Clevis 2-28, 2-36, 2-38P110, Pin, 3/8” x 1 5/16” Clevis, Yzn 5-8, 6-6P11035, Bearing, 6206-2NSE 5-18, 5-22, 6-12, 6-16P111, Ring, 1” Kick-Out 2-34, 2-38P111, Ring, 1” Kick-out 4-12P111, Ring, Kick-out, 1” 2-32, 5-8, 6-6P11258, Strap, 24” Rubber w/Hooks 4-20P117, Decal, Hands & Feet 1-6P12161, Washer, Felt Battery Terminal 4-20P12708, Fitting, 3/8” NPT-3/8” Barb Elbow 3-14, 3-16P12724, Fitting, 3/8” NPT-3/8” Barb 3-14, 3-16P12724, Fitting, 3/8” NPT-3/8” Barb 4-10P12739, Hose Clamp, 11/16” Worm 3-16P128, Blade, 21” x 2 1/2” x 1/4” High Lift 5-16, 5-20P190, Bearing, 1” ID Tapered Roller 2-20P191, Seal, 1 1/4” ID Trb Bearing 2-8, 2-10P195, Cap, Hub 2-8, 2-10, 2-40P212, Pin, 3/8” x 2 1/8” Clevis 2-34P212, Pin, 3/8” x 2 1/8” Clevis, Yzn 2-32, 5-8, 6-6P246, Blade, 21” Low-Lift 5-16, 5-20P292, Bearing, Tapered Roller, 3/4” ID 2-22P293, Seal, TRB, 3/4” ID 2-22P294, Fitting, 1/4-28 45 Deg Grease 4-14, 5-24, 6-18P296, Spacer, 1.13” OD x .75” ID x .5” 2-20P322, Blade, 21” Gator Mulching 5-14, 5-16, 5-20P402, Bearing Race Insert, 3/4" TRB 2-22
P434, Nut, 3/4-16 Castle 2-20P478 , Decal, Danger - Rotating Blades 1-4, 1-6P485, Decal, Fuel Equipment 4-4P485, Decal, Fuel Equipment 325E 1-4, 1-6P611, Holder, Jumbo Cup Black 2-40P619, Filter Head, 3/8” NPT 3-14, 3-16P620, Filter Element, Spin On, BE-25-25 Zinga 3-2, 3-4,
3-14, 3-16P629, Grip, Foot Control Black 2-28P630, Seat, Air Ride (Color Gray) 2-2P649, Hose Clamp, 7/32”-5/8” 3-16P686, Yoke, 3/8In-24 2-28P701, Blade, 25” x 2 1/2” x 1/4” High Lift 6-10, 6-14P776, Seat Belt, 2” ALR/ERI Buckle 2-2P786, Bushing, 3/4” ID x 1” OD x 5/8” Lng Flanged
2-36, 4-16P826, Switch, Seat 2-2P829, Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz 2-12,
2-14, 2-16P848, Blade, 25" Gator Mulching 6-10, 6-14P849, Blade, 25” x 2 1/2” x 1/4” Low Lift 6-10, 6-14P849, Blade, 25” x 2-1/2” x 1/4” Low Lift 6-22SS08291-W, Handle, Power/Feed & Up/Down 4-8S12284, Tube, 7/8” Dia Elec Motor Spacer 2-32S12284, Tube, 7/8” Dia. Elec Motor Spacer 2-34S21486, Key, 1/4” SQ x 3-3/8” Long 4-10
Index Lastec//072815 11
Top Related