americanchemistry.com® 700 Second St., NE | Washington, DC 20002 | (202) 249.7000
Spray Polyurethane Foam: Benefits for Passive
Houses
ACC Center for the Polyurethanes Industry
5/9/2012
For further information contact: Chris Braddock, Director ACC Center for the Polyurethanes Industry (202) 249-6617
1
Spray Polyurethane Foam: Benefits for Passive Houses
The Center for the Polyurethanes Industry1 and the Spray Foam Coalition,
2 which are part of the
American Chemistry Council (ACC), represent U.S. producers or distributors of chemicals and equipment
used to make polyurethane or manufacturers of polyurethane products. Passive House Institute US
(PHIUS) has provided ACC an opportunity to publish a document in the PHIUS newsletter alongside a
document by the PHIUS Technical Committee on spray polyurethane foam (SPF). We appreciate the
opportunity extended to us to discuss and to clarify some reasons why SPF can be an excellent choice for
Passive Houses.
As those involved with PHIUS know, as much as 40% of a building's energy is lost due to air infiltration.
SPF offers a solution: it performs as both insulation and an air sealant, or air barrier, closing those gaps
and cracks that let air escape. SPF combines two key attributes vital for passive houses in one product.
As SPF has been utilized more in recent years due to the value that builders, specifiers and consumers see
in its unique insulating and air sealing properties, there has also been a corresponding increase inaccurate
information about SPF and its component materials. We are not attempting to address every aspect of
SPF in this document, but we highlight specific issues, many raised in the PHIUS document within the
newsletter this month. More information about spray foam can be found on www.spraypolyurethane.org
and www.whysprayfoam.org. We encourage you to review those websites for any questions you have
about SPF now or in the future.
TYPES OF SPF AND THEIR APPLICATIONS
Spray polyurethane foam is an insulation and roofing material that is formulated on the jobsite by the
combination of Methylene Diphenyl Diisocyanate (MDI) or “A-side” with an equal amount of a polyol
blend or “B-side. While the formulation of the A-side is essentially constant, the proprietary formulations
of the B-side, which includes polyols, blowing agents, flame retardants, catalysts and surfactants, varies
depending on the desired properties of the foam.
There are three basic classifications for SPF used in the U.S. construction industry for insulation and
roofing systems. These classifications are based on material density and cell structure. A summary of
key physical properties of these foams is provided in Table 1.
The first classification is open-cell or low-density SPF. This material has a core or nominal density of 0.4
to 0.7 pounds per cubic foot (pcf), and often this type of foam is referred to as “half-pound” or “water-
blown” foam. These foams are formed using a reactive blowing agent, which is typically water. Water
reacts with the A-side MDI to create CO2 gas that expands the curing liquid into a cellular foam material.
1 The Center for the Polyurethanes Industry (CPI) of the American Chemistry Council serves as the voice of the
polyurethanes industry in North America, promoting its sustainable development and coordinating with
polyurethane trade associations across the globe. CPI members are companies that produce and sell the raw
materials and additives that are used to make polyurethane products, equipment used in the manufacture of
polyurethanes, and companies engaged in end-use applications and the manufacture of polyurethane products. 2 The Spray Foam Coalition (SFC) champions the use of spray polyurethane foam in U.S. building and construction
applications and promotes its economic, environmental and societal benefits while supporting the safe manufacture,
transport, and application of spray polyurethane foam. SFC consists of manufacturers of spray polyurethane foam
systems as well as suppliers of raw materials and machinery used to apply the foam.
2
Since this material has an open cell structure, the cells are filled with air, so that the thermal performance
(R-value per inch thickness or thermal resistivity) is equivalent to fibrous insulations such as fiberglass,
cellulose and stone wool – in the range of R3.6 to R4.0 per inch. Like these fibrous products, open-cell
SPF is permeable to moisture, and may need an additional vapor retarder in cold-climate building
applications. Unlike fibrous insulations, open-cell SPF is far less air permeable, and can also serve as an
air barrier material at certain thicknesses.
The second SPF class is closed-cell or medium-density SPF. This class of foam has a core or nominal
density between 1.7 and 2.3 pcf, and is often called “two-pound” foam. This material has a cell structure
where 90% or more of the cells are closed. When fluorocarbon (physical) blowing agents are used, the
fluorocarbon liquid in the B-side converts to a gas from the heat of the reaction to expand the cells. Like
a double-pane insulated window, this low thermal conductivity fluorocarbon gas is retained in the closed
cells, yielding a thermal resistivity between R5.8 to R6.8 per inch, which can be nearly twice that of an
open-cell foam or fibrous insulation. Medium density SPF is resistant to water absorption and effectively
impermeable to moisture and air. In addition, medium density foams have measureable stiffness and
strength and can provide a moderate increase in the structural performance of certain building assemblies.
The third class of SPF is roofing foam. Like medium density foams, these materials have a closed cell
structure using the same captive fluorocarbon blowing agents as a medium density SPF. The major
difference between roofing SPF and medium density SPF is the foam density. Roof foams have densities
typically ranging from 2.5 up to 4.0 pcf, and are often called “three pound” SPF. This increased density
provides a higher compressive strength needed to support foot traffic when installed on top of surfaces of
a low slope roof.
The three classes of SPF described above are applied by professionally-trained contractors to large areas
of the building envelope using a two component, high-pressure delivery systems. For insulation of
smaller areas, two-component low-pressure, self-contained kits may be used by trained professional
applicators. In addition, there are also single-component systems delivered in small aerosol cans where
the A and B sides are pre-mixed. These one-component polyurethane sealant foams are used for air
sealing. In recent years, foam formulations that have densities, closed-cell content and thermal
performance that fall in between the three traditional foam classifications described above have been
developed. Since these foams are still being introduced, this paper will be limited to the three traditional
SPF classes described above.
Table 1: Summary of SPF properties
Sealant Low-Density or
ocSPF Medium-Density
or ccSPF Roof SPF
Density (pcf) 0.6 – 1.8 0.4 – 0.7 1.7 -2.3 2.5 – 4.0
Thermal Resistivity (R/in) not reported 3.6 - 4.5 5.8 - 6.8 5.8 - 6.8
Air Impermeable Material * (>4-6") (>1") (>1")
Integral Air Barrier System
Class II Vapor Retarder
(>2") (>2")
Water Resistant
Cavity Insulation
Continuous Insulation
Low-Slope Roofing
Structural Improvement
3
SPF INGREDIENTS
Two-component SPF is manufactured on-site by trained, professional applicators. It is created by mixing
two components in a 1:1 volumetric ratio (the A-side isocyanate and the B-side polyols).
The A-side of SPF is made from a blend of MDI (Methylene Diphenyl Diisocyanate). Typical A-side
blends consist of monomeric and polymeric forms of MDI.
The B-side directly controls the type of foam that is created, impacting the physical and mechanical
properties of the foam. In the U.S., companies called Systems Houses develop and manufacture the B-
side. While each formulator typically offers a number of different B-side formulations for different
applications, these exact proprietary formulations are not published for competitive reasons.
SPF B-side formulations for SPF use five basic chemical classes: polyols, blowing agents, catalysts,
flame retardants and surfactants. For high pressure two-component foams, the blowing agents are
included in the B-side. For low-pressure foams, the blowing agent is mixed into the A-side. Table 2
shows examples of the typical compounds and the percentages used in the B-side of high-pressure SPF.
Table 2: Options for Typical B-Side Components
CHEMICAL CLASS Open-Cell SPF
0.5 pcf insulation
Closed-Cell SPF
2.0 pcf insulation
Roofing SPF
3.0 pcf roofing
POLYOLS
Polyester - 45% 35%
Compatibilizer 10% - -
Polyether 35% 30% 45%
BLOWING AGENTS
Reactive (water) 24% 2% 2%
Physical (fluorocarbon) - 9% 7%
FLAME RETARDANTS
TCPP 25% 4% 8%
Brominated/TCPP - 6% -
CATALYSTS
Amine 6% 3.0% 2%
Metal - <1% <1%
SURFACTANTS
Silicone <1% <1% <1%
B-Side Open-Cell SPF
POLYOLS
FLAME RETARDANTS
BLOWING AGENTS
CATALYSTS
SURFACTANTS
B-side Closed-Cell SPF
4
Polyols constitute a significant portion of the B-side formulation. Generally, a blend of polyester or
polyether polyols is used; these are petroleum based. Some SPF products use an alternative source of
polyols from natural sources such as soybeans, castor or rapeseed oils (not shown in the table above).
Current technology limits the use of natural oil polyols to about 1/3 of the total polyols as excessive use
of natural oil polyols can affect the dimensional stability of SPF.
When polyols are combined with MDI, a solid polyurethane material is the resulting product. In order to
create a cellular structure to the foam, a blowing or expanding agent is required. SPF uses two types of
blowing agents: reactive and physical. Water is the reactive blowing agent used to make all open-cell
SPF, and a small percentage of closed-cell foams. Water reacts with MDI to create CO2 gas that expands
the foam. Physical blowing agents used in SPF are fluorocarbon gases. These are present in liquid form
in the B-side. The exothermic reaction with the A-side converts this liquid into a gas to expand the foam.
The low thermal conductivity fluorocarbon gas is contained inside the closed-cell structure to provide
increased thermal resistance.
The creation of SPF involves two major competing processes: the curing of the MDI-polyol into
polyurethane and the development of the cell structure by the blowing agent. These competing processes
are moderated by the use of catalysts to control the speed of the curing reaction. Catalysts directly
influence the rise time of the foam, and ultimately whether or not the foam will be open or closed cell.
SPF typically uses amine-based catalysts, although some formulations may use metal-based catalysts as
well.
Polyurethane foams, like all plastic foams and many other organic materials, are combustible. To meet
the rigorous demands of SPF applications, flame retardants are used. These chemicals are stable and
generally have long life characteristics needed to retain performance in insulating foams.
POTENTIAL EXPOSURE RISKS AND ENVIRONMENTAL IMPACTS
As with all building materials, SPF should be used with care. While many plastic building products are
manufactured using the same or similar chemicals, SPF has the unique attribute of being installed and
manufactured at the building site. The potential health effects that could result from SPF exposure are
contained in the product MSDS, which describe how a worker or bystander could potentially be exposed
to SPF chemicals by breathing chemical mists or vapors or through skin or eye contact. A few key points
are presented here. Extensive information on health and safety considerations for SPF is available at
www.spraypolyurethane.org and www.polyurethane.org.
A-Side: MDI
Overexposure to MDI can cause skin, eye, nose, throat, and lung irritation. Overexposure can also lead to
skin or to respiratory sensitization in some individuals. To prevent these adverse health effects, the
Occupational Safety and Health Administration (OSHA) has established a permissible exposure limit
(PEL) for 4,4’-MDI of 0.2 milligrams per cubic meter (mg/m3) as a ceiling concentration. The American
Conference of Governmental Industrial Hygienists (ACGIH) recommends a threshold limit value (TLV)
8-hour time-weighted average (TWA) exposure limit of 0.051 mg/m3.
Airborne MDI levels in the breathing zone of the SPF applicator during installation commonly result in
levels above the occupational exposure limits previously referenced. To prevent exposure to MDI, SPF
applicators use personal protective equipment (PPE) such as gloves, coveralls, and respirators (see
www.spraypolyurethane.org for information about PPE). In addition, many SPF contractors use
engineering controls (e.g., forced air such as exhaust fans or blowers) during interior SPF installation
work to help reduce the airborne concentrations of SPF chemicals in the work area.
5
Soon after SPF application work is completed, airborne MDI concentrations can rapidly decrease
according to an air monitoring study conducted by Lesage, et.al.1 In this study, five residential structures
during and following SPF application indicated that airborne MDI could not be detected in air samples
collected 1-hour following the end of SPF installation. Furthermore, surface wipe samples collected from
newly-installed SPF surfaces indicated that unreacted isocyanates were not detected 15 minutes following
the end of SPF installation.
Other studies (Roberge, et.al IRRST2 and Karlovich, Bayer
3) also indicated that within two hours
following the end of spraying, airborne MDI levels are not detectable. The IRRST study indicated that
within two hours following the end of spraying, airborne MDI levels were at extremely low levels, below
the EPA MDI Reference Concentration (RfC) of 0.6 micrograms per cubic meter (ug/m3).
B-Side
In the B-side, there may be ingredients that present potential human health risks, when humans are
overexposed to them.4 High concentrations are generally present when the raw chemicals are
manufactured or blended by the formulators. These upstream chemical operations usually take place
under controlled and regulated manufacturing conditions, with personnel following proper safety
precautions as required by OSHA.
Polyols
The major component of the B-side is polyols. Polyols are oil-like liquids that are used in many different
products, including personal care products like shampoo, skin creams and baby oil.
Fluorocarbon Blowing Agents
For the past five decades, closed-cell SPF has used fluorocarbon compounds. In the United States, the
first SPF blowing agents were CFC-11, followed by HCFC-141b and then HFC-245fa. These different
blowing agent have evolved over the past three decades in order to eliminate the ozone depletion potential
(ODP) of certain fluorocarbon gases. Today’s third-generation blowing agent for high-pressure closed-
cell SPF, HFC-245fa, used since 2003 and mandated by EPA, has zero ozone depletion potential, but
does have a global warming potential (GWP) of 1020 CO2 equivalents. In the coming years, fourth
generation, hydro-fluoro-olefin (HFO) based blowing agents with zero ODP and GWP from 6-15 CO2
equivalents are anticipated. The table below summarizes the evolution of blowing agents for high-
pressure, closed-cell SPF.
Table 3: Blowing Agents
Years Generation SPF Blowing Agent ODP GWP
1960s -1993 1 CFC-11 1.0 4750
1993 - 2003 2 HCFC-141b 0.12 760
2003 - pres 3 HFC-245fa 0 1020
2013? 4 HFO 0 6 - 15
Aside from the published ODP and GWP environmental impacts, development of fluorine-based blowing
agents include several years of extensive bio-assay testing to measure human toxicity, and carcinogenic,
mutagenic and reproductive (CMR) effects, prior to commercialization as required by the EPA. This
testing has shown no measurable impacts.
6
Flame Retardants
Flame retardants are incorporated in SPF as a part of the B component to prevent fires from starting
and/or to dramatically slow the burning process. To meet the rigorous demands of SPF applications,
phosphorus and halogen based flame retardants are used. Typically the flame retardants used include Tris
(1-chloro-2-propyl) phosphate (TCPP) combined with a reactive brominated compound which bonds into
the polymer or a polymeric brominated flame retardants. These chemicals are stable and offer long life
characteristics needed to retain performance in insulating foams. These and other flame retardants enable
SPF and other insulations to meet the National Fire Protection Agency (NFPA) and building code
requirements. Some flame retardants have gone through the full European Union risk assessment as well.
Catalysts
Most catalysts used in SPF are amine based. Overexposure to airborne concentrations of amine catalysts
may result in irritation to the respiratory system, skin, and eyes.5 Under certain installation conditions,
there may be unreacted amine catalysts that can be emitted from SPF. These catalysts can create a
distinct odor that can be noticed by some people. It is often described as a fishy or urine like odor. While
these odors present a nuisance to some, ventilation of the workspace for a few days after application
usually solves the problem. Covering the foam with thermal or ignition barriers may also reduce these
odors. Levels above the threshold to cause halo-vision are typically found during and immediately after
spraying and a combination of work zone ventilation and proper PPE protect workers from these
chemicals.
Surfactants
Silicone-based surfactants are used in very small quantities to control the formation and shape of the cells
during curing.
Installed Foam
When the A- and B-side components are combined, numerous chemical reactions take place
simultaneously. Most notably, the MDI and polyols combine to make polyurethane. Reactive blowing
agents (water) react with MDI to create CO2 gas to expand the cells. In addition to these primary
reactions, the flame retardants, catalysts and surfactants undergo side reactions during the process. Many
of the known potential chemical hazards from these raw materials change when they undergo chemical
transformations during processing.
It is often stated that SPF emits volatile organic compounds or VOCs. Several SPF products have
undergone standardized VOC testing in both the US (GreenGuard6 and CA 01350
7 standards) and in
Canada (ULC S7748). These tests show that the SPF tested meets all of the VOC limits in these standards
and thus SPF is not considered to be source of standard VOCs in these tests.
As stated earlier in this paper, airborne levels of MDI may be above the occupational exposure limit
during SPF application, but drop off rapidly both with distance and time. In fact, researchers have shown
that for interior SPF application work, within two hours following the end of spraying, airborne MDI
levels were not detectable.9
At present, an ASTM workgroup with participants from EPA, NIOSH, OSHA, emission laboratories and
the chemical industry are working to develop a new emissions test protocol to measure SPF-specific
emissions from MDI, blowing agents, and catalysts.
7
Disposal and Recycling
SPF has been determined safe for disposal in landfills as it does not meet the criteria of a hazardous waste
according to the Resource Conservation and Recovery Act. Although landfilling of foam plastics appears
to be the most common disposal method today, some SPF materials are shredded and used as filler
materials. SPF can be incinerated and used as a fuel. Chemical processing to degrade polyurethane foam
into usable chemicals is being done on a limited basis, particularly in Europe.10
When incinerated, the
GWP of the retained fluorocarbon blowing agents is eliminated by combustion. A study was conducted
to consider sequestration of fluorocarbon blowing agents in foam plastics, but it was determined that the
environmental impact of transportation of the materials to a central processing location would far
outweigh the impacts of the released blowing agents.11
THERMAL PERFORMANCE
As mentioned previously, open-cell SPF provides thermal resistance by creating still air pockets in the
open-cell foam structure. Conversely, closed-cell SPF provides improved thermal resistance from low
thermal conductivity blowing agents retained in the closed-cell structure. It is known that these captive
blowing agents can, over time, diffuse from the cells near the free surfaces of the foam, resulting in a
slightly lower R-value than measured immediately after installation. To address this under the Federal
Trade Commission (FTC) Insulation Rules (16 CFR 460)12
, all foam plastic insulations are aged prior to
measuring and reporting R-value. For several decades, the practice for closed-cell SPF is to age the
sprayed foam for 180 days under room temperature conditions before measuring the reported R-value.
More recently, accelerated aging processes (90 days at 140ºF) have been shown to provide the same
result.13
After aging, all SPF products are tested in a guarded hot plate apparatus using the procedures
outlined in ASTM C518.14
Traditionally, aging and thermal testing of SPF has been performed on 1” thick specimens, as this is a
common thickness for SPF roofing installations. As SPF is also used as interior insulation, most
manufacturers also test closed-cell foams at 3-4” thicknesses. This testing requirement, including the use
of a third-party, accredited laboratory for conditioning and thermal testing, is described in International
Code Council Evaluation Services (ICC-ES) Acceptance Criteria for Spray Foam Plastics (AC-377).15
Any SPF product that has an ICC-ES Evaluation Services Report has undergone thermal testing by a third
party laboratory.
Diffusion of blowing agents may occur near the free surfaces of the foam and may be slightly lower the
thermal performance of closed-cell SPF. After the initial diffusion of the blowing agent which
measurably lowers thermal performance, the blowing agent remaining in the core of the material is
released much more slowly. Over several millennia, the captive blowing agent in the core may be
completely released, but it is not likely to occur over the 60-100 year service life of the building. Below
are the results of a study showing the thermal conductivity or k-value (inverse of the thermal resistivity,
R/inch) of a closed-cell SPF material.16
After a few months, the thermal conductivity reaches a stable
value, which continues to increase very slightly over time.
8
Based on this and similar studies, the SPF industry believes that 180-day room temperature aging prior to
R-value testing per ASTM C518 provides a suitable estimate of the long-term thermal performance of
closed-cell SPF.
Loss of initial R-value from blowing agent diffusion is controlled by several factors. For SPF, there are
surface skins, pass lines and substrates that can provide barriers that slow blowing agent diffusion. These
features are often dependent on specific installation. There are conditioning protocols for foam plastic
insulation that involve thin-slicing of the material and subsequent thermal measurement of these slices
(ASTM C130317
and CANULC S77018
). While these methods have been shown to work well with some
foam plastic insulations, there are concerns that these conditioning techniques will invasively damage the
closed-cell structure of SPF, and may not include the real-world affects provided from substrates, skins
and pass lines in mitigating the diffusion of blowing agents. Research is underway to determine if the
thin-slice test methods are appropriate for closed-cell SPF.
MOISTURE CONTROL
In colder climates, moisture permeable insulations like fiberglass, cellulose and open-cell SPF require
additional vapor retarders (films or paints) applied to the interior surface to avoid unwanted condensation.
Closed-cell SPF, at a thickness of about 1.5 inches, provides an inherent moisture permeance of 1 perm,
meeting Class II vapor retarder requirements per the model building codes.19
Closed-cell foam is also
water resistant and meets current FEMA standards for flood-resistant materials,20
which can make it an
excellent choice for insulating areas at or below grade in most buildings.
20.0
20.5
21.0
21.5
22.0
22.5
23.0
23.5
24.0
24.5
25.0
0 10 20 30 40
Time, months
Th
erm
al C
on
du
cti
vit
y, w
/mK
Region 1
Region 2
Region 1 - Air Infiltration & CO
2 Diffusion Dominate Aging
Region 2 - Both Phenomenon
Impact Aging Rate
Region 3 - Blowing Agent Diff- usion Dominates Aging
Region 3
Table 4: Thermal conductivity (inverse of R/inch) of a closed-cell SPF material
9
Air sealing of walls can be achieved using a small thickness of closed-cell SPF. Thus, closed-cell SPF is
frequently used in tandem with fibrous insulations to create a hybrid insulation system that is known as
“flash and batt.” For high-pressure closed-cell foam, it can be applied at a thickness of 1-3 inches in the
wall cavity against the exterior sheathing, and the remainder of the cavity is filled with fibrous insulation
to achieve the desired R-value. In this application, an interior vapor retarder is usually unnecessary if the
closed-cell foam is installed to an appropriate thickness. The appropriate thickness of foam, determined
by hygrothermal (WUFI21
) modeling, can provide between 25 and 65% of the total cavity R-value,
depending on climate zone. Moderate climates (IECC Zone 4) require about 25%, while colder climates
(IECC Zone 6-7 require about 65%. These insulation percentages are included in Table 601.3 of the 2009
IRC.22
AIR SEALING
The Air Barrier Association of America (ABAA) provides an excellent definition for air barrier materials,
assemblies and systems on their website.23
It states that open-cell SPF is air impermeable at a thickness
between 3.5 and 5.5 inches, per ASTM E2178 or E283. Closed-cell SPF is air impermeable at a thickness
of 1.5 inches using these tests. At these installed thicknesses, both product classes qualify it as an air-
barrier material per ABAA, and an air impermeable material per the model building codes. These
qualities of spray foam are important to make large energy efficiency gains and demonstrate one of the
key benefits that spray foam brings to a passive home.
When SPF is applied in a wall assembly, it can expand to fill most cracks and gaps. Test data from an
ABAA study24
shows that spray foamed wood-frame wall assemblies have air leakage far below the
maximum assembly leakage limits per ABAA.25
When SPF is used as a component of an air barrier system, other air sealing details may be required. For
example, wood-framed walls often use double-studs (crips and jack studs) around fenestration. SPF
cannot seal these sources of air leakage, and caulking may be recommended.
As for whole building air leakage, there are a number of studies that demonstrate air sealing performance
of SPF insulation. A study conducted by NAHB26
shows that open-cell homes have reduced air leakage
rates. A 2009 study was conducted on three identical homes built in San Antonio, TX.27
The control
home conventionally insulated with blown fiberglass on the attic floor and fiberglass batts in the walls
had measured air-leakage of 5.84 ACH50. The same home with fiberglass insulated walls and open cell
SPF used to create an unvented attic had a measured air leakage of 3.64 ACH50. A third identical home
using SPF insulation throughout the entire envelope had a leakage rate of 1.95 ACH50. All homes had
identical house wrap and a caulk and seal package. The study showed a three-fold decrease in air leakage
between fiberglass and SPF insulated homes. A HERS evaluation of a SPF insulated home, with a caulk
and seal package, foam around all doors and windows with taped window flashing achieved an air
leakage rate of 0.41 ACH50.28
SPF plays a significant role in minimizing air leakage. Air leakage not only improves energy efficiency,
but also reduces uncontrolled moisture movement through the building envelope, which can result in
condensation and mold, mildew, rot and corrosion, reducing the service life of the building. Minimizing
air leakage from SPF use can improve indoor air quality and occupant comfort by controlling the entry of
pollen, outdoor pollutants and pests into the building.
STRUCTURAL BENEFITS OF SPF
The structural improvements provided by closed-cell SPF are well documented. Several studies
measuring the racking performance of frame walls per ASTM E72 show that 1 to 2 inches of closed-cell
foam can provide nearly the same racking strength of a frame wall using plywood sheathing.29
,30
,31
In
10
2008, a study32
showed that wind uplift resistance of wood roof decks increased more than three times by
using 3 inches of closed-cell SPF between rafters under a typical plywood roof deck. Not only does
closed-cell SPF provide significant structural benefits as described above, its inherent water resistance can
provide a secondary water barrier – which is important when the primary roof system (shingles and
underlayment) are removed in a hurricane.
SPF AND SUSTAINABLE BUILDINGS
At present there are many opinions for selecting sustainable building materials for both residential and
commercial construction. Several of these programs suggest certain minimums on recycled content or
renewable resources used to make and install the product. These restrictions are considered single
attribute measures. While they represent ways to minimize a particular environmental impact, they can
mistakenly overlook the entire set of impacts of a product throughout its complete life. For example, the
environmental impacts of collecting and processing certain recycled materials can be greater than the
environmental impact of landfilling of a material.
To properly address the environmental impacts of a product, an ISO-compliant33
life-cycle assessment
(LCA) is an important tool. Generally, LCAs include the entire product life cycle, from cradle to end-of-
life. These include processes needed to mine, extract and process raw materials, manufacture them into
finished products, as well as the impacts of using and disposing or recycling the products. LCAs typically
measure standard environmental impacts such as primary energy demand, and potentials for global
warming, acidification, eutrophication, ozone depletion, and smog creation for a functional unit of the
product throughout its entire life. LCAs can incorporate all of the single-attribute measures, without
favoring one over another.
The Spray Polyurethane Foam Alliance (SPFA) commissioned an LCA project in November 2010, and
the results will be published in mid-2012. The results include all impacts from raw materials,
manufacturing, transportation and disposal offset by the environmental impacts avoided by the energy
saved over the life of a typical building. The final report of this study will be of interest to passive house
practioners.
In terms of super-insulated buildings, there is a well-known diminishing return on increasing R-value. As
we consider designs of super-insulated buildings, LCA approach should be considered, not a single-
attribute measure of the product. For example, many super-insulated buildings require thick walls that
can exceed 2-3 feet in thickness to achieve R60 walls. This requires use of more framing materials with
associated negative environmental impacts. In addition thick walls combined with small windows reduce
natural daylighting in these buildings – perhaps requiring the use of supplementary lighting during
daylight hours. This lighting can have a negative impact, which may or may not be offset by the
incremental heat savings moving from an R30 to an R60 wall. These types of interactions must be
considered for sustainable building design, and a life cycle assessment provides a transparent means to do
so.
CONCLUSIONS
SPF has many benefits for passive houses and can increase energy efficiency. While SPF is a unique
product since it is manufactured onsite, it can be handled and applied safely by a trained professional
applicator. SPF can provide benefits beyond those of conventional fibrous insulation materials. Both
open and closed-cell SPF are air barrier materials and provide a significant contribution to reduced air
leakage in buildings. Closed-cell foam also provides an inherent vapor retarder meeting Class II vapor
retarder requirements of the model building codes and provides structural reinforcement.
11
SPF has unique attributes that make it ideal for use in passive homes and builders, architects and
homeowners should learn more about the product before making a decision on its positive or negative
attributes prior to utilizing the product. A key to a successful experience with SPF in a passive house, or
on any building, is hiring a trained and experienced professional contractor, who knows and understands
the proper way to install SPF and follows the manufacturer’s guidelines.
Significantly more information about SPF can be found on www.spraypolyurethane.org and
www.whysprayfoam.org. We encourage you to review those websites for any questions you have about
SPF now or in the future.
Disclaimer: This document was prepared by the American Chemistry Council’s Center for the Polyurethanes
Industry and the Spray Foam Coalition. It is intended to provide general information and not intended to serve as a
substitute for in-depth training or specific construction requirements, nor is it designed or intended to define or
create legal rights or obligations. All persons involved in construction projects including spray polyurethane foam
have an independent obligation to ascertain that their actions are in compliance with current federal, state and local
laws and regulations and should consult with legal counsel concerning such matters. Neither the American
Chemistry Council, nor the individual member companies of the Spray Foam Coalition, Center for the
Polyurethanes Industry, or the American Chemistry Council, nor any of their respective directors, officers,
employees, subcontractors, consultants, or other assigns, makes any warranty or representation, either express or
implied, with respect to the accuracy or completeness of the information contained in this document; nor do the
American Chemistry Council or any member companies assume any liability or responsibility for any use or misuse,
or the results of such use or misuse, of any information, procedure, conclusion, opinion, product, or process
disclosed in these Guidelines. NO WARRANTIES ARE GIVEN; ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED.
This work is protected by copyright. Users are granted a nonexclusive royalty-free license to reproduce and
distribute these guidelines, subject to the following limitations: (1) the work must be reproduced in its entirety,
without alterations; and (2) copies of the work may not be sold.
Copyright © May 2012, American Chemistry Council.
1 Lesage, J., J. Stanley, W.J. Karoly, and F.W. Lichtenberg. 2007. “Airborne Methylene Diphenyl Diisocyanate (MDI)
Concentrations Associated with the Application of Polyurethane Spray Foam in Residential Construction”, J. Occup. Environ.
Hyg. 4:145–155. 2 Roberge B.; R. Gravel; D. Drolet. 2009. Diphenylmethane-4,4'-diisocyanate (MDI): Safety Practices and Concentration during
Spraying of Polyurethane Foam. IRSST Report R-606. Montreal, Quebec, Canada. 3 Karlovich, B. 2009. “Air Monitoring Investigation: SPF Installation in Residential Dwellings”, Bayer Material Science,
Unpublished report. 4 American Chemistry Council Center for the Polyurethanes Industry. Health and Safety Product Stewardship Workbook for
High-Pressure Application of Spray Polyurethane Foam (SPF). March 15, 2010. Available at www.spraypolyurethane.org. 5 ACC CPI Health and Safety Workbooks for SPF. 6 GreenGuard Environmental Institute certification programs www.greenguard.org. 7 “Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using
Environmental Chambers” http://www.cal-iaq.org/phocadownload/cdph-iaq_standardmethod_v1_1_2010%20new1110.pdf 8 CAN/ULC S774 - “Standard Laboratory Guide for the Determination of Volatile Organic Compound Emissions from
Polyurethane Foam.”
http://www.ul.com/canada/documents/ulcstandards/standardsbulletins/2009english/Standards_Bulletin_2009-16_%28S774-
09%29_EN.pdf. 9 Lesage, et al. 10 Simioni F, Modesti M. Glycolysis of flexible polyurethane foams. In: Buist JM, editor. Cellular polymers, vol. 12. Shrewsbury:
Rapra Tech. Ltd; 1993. p. 337-48. 11 California Air Resources Board Scoping Plan – December 2008.
http://www.arb.ca.gov/cc/scopingplan/document/scopingplandocument.htm.
12
12 Federal Trade Commission 16 CFR Part 460. Trade Regulation Rule: Labeling and Advertising of Home Insulation.
http://www.ftc.gov/os/1999/08/rvaluefr.htm. 13 ASTM Standard C1029-10 , "Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation"
ASTM International, West Conshohocken, PA, 2010. www.astm.org. Spring 2009 Meeting. Changes to allow accelerated aging
at 140F for 90 days added to Section 10.1. 14 ASTM Standard C518-10 , " Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat
Flow Meter Apparatus" ASTM International, West Conshohocken, PA, 2010. www.astm.org. 15 Acceptance Criteria for Spray-Applied Foam Plastic Insulation, AC-377, June 2011. International Codes Council – Evaluation
Services. 16 Bogdan, M., Hoerter, J. and Moore, F. “Meeting the Insulation Requirements of the Building
Envelope with Polyurethane and Polyisocyanurate Foame” Polyurethanes Expo 2003. 17 ASTM Standard C1303-10 , " Standard Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam
Insulation" ASTM International, West Conshohocken, PA, 2010. www.astm.org. 18 CAN/ULC S770-09 Standard Test Method for Determination of Long-term Thermal Resistance of Closed-Cell Thermal
Insulating Foams. Underwriters Laboratories of Canada, 2009. 19 2009 International Residential Code for One and Two Family Dwellings (IRC). International Code Council 2009. Chapters 6
and 9. 20 FEMA Technical Bulletin 2-08, “Flood Damage-Resistant Materials Requirements for Buildings Located in Special Flood
Hazard Areas in accordance with the National Flood Insurance Program”, August 2008. 21 WUFI "Wärme- und Feuchtetransport instationär" ("Transient Heat and Moisture Transport"). Hygrothermal simulation
software for building envelope assemblies. 22 2009 International Residential Code for One and Two Family Dwellings (IRC). International Code Council 2009. Table
601.3. 23 Air Barrier Association of America (ABAA), http://www.airbarrier.org/ 24 “Full-Scale Testing and Evaluation of Air-tightness Performance of Different Types of Air Barrier Systems” Sponsor Report,
November 2011. 25 ABAA Assembly Air Leakage Limit, http://www.airbarrier.org/about/materials_e.php 26 “Air Infiltration Data Analysis for Newly Constructed Homes Insulated with [Open Cell] Spray Foam.” Upper Marlboro, MD
20774: NAHB Research Center, November 2007. 27 “Measured Performance of Side-by-Side South Texas Homes”, D. Chasar, J. Sherwin, V. vonSchramm, S. Chandra, DOE
Buildings XI Conference, December 2010. 28 HERS blower door rating of home at 572 Pardee Road, Millmont, PA. September 2009. Hadad Associates, Bellefonte, PA. 29 Technical Note 91.1, “Effect of Spray Applied Polyurethane Foam Insulation on the Racking Load of a Plywood Sheathed
Wood Frame Wall”, Council of the Forest Industries of B.C., Canada. 30 “Testing and Adoption of Spray Polyurethane Foam for Wood-Frame Wall Construction”, Phase II Wall Performance Testing,
NAHB Research Center, Upper Marlboro, MD. May 1992. 31 “Racking Test Data” Letter to SPI from NAHB Research Center, Upper Marlboro, MD. November 1996. 32 Duncan, R., Wu, J. “Closed-Cell Spray Foam: Resisting Wind Uplift in Residential Buildings”, SPFA Technical Conference
and Exhibition 2008. 33 ISO 14044:2006 Environmental management -- Life cycle assessment -- Requirements and guidelines.
Top Related