DOC. NO. 5956.573.04 P. 1 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
SERVICE MANUAL
MODULAR AND COMPACT
RACK-TYPE DISHWASHERS
CONTENTS: This document contains all the parameters and information for programming the electronic boards.
EDITION: 03.2010
Valid for firmware versions
• 1.65 COMPACT SHORT • 1.67 USA MODULAR• 1.66 MODULAR• 5.01 COMPACT USA.
WARNING:
All the safety regulations and procedures to be followed by the Specialised Technician/Technical Assist-ance performing electrical, mechanical or electronic maintenance operations are contained in the instruc-tion manual supplied with the machine: refer to this document before operating. This applies for anyonecarrying out operations using these documents. The specialised technician must wear personal protec-tion equipment suitable for the work being performed (e.g. gloves, safety glasses and shoes, suitableclothing, etc.) and use appropriate tools, equipment and auxiliary means.
U
U
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
INDEXA FUNCTION KEYS............................................................................................. Pag.4
A1 DISPLAY OF AUXILIARY VALUES ................................................................................. Pag.4A1.1 MODULAR MACHINES (NO USA) ..................................................................... Pag.4A1.2 COMPACT MACHINES AND USA MODULAR VERSIONS ............................... Pag.5
A2 ACCESSING THE USER MENU AND SERVICE MENU................................................ Pag.6A3 USER MENU (NOT AVAILABLE FOR USA COMPACT RACK TYPES)........................ Pag.7
A3.1 EXIT .................................................................................................................... Pag.7A3.2 DATA SETTING (FOR NON USA MODULAR RACK TYPES ONLY) ................. Pag.7A3.3 CONSUMPTION ................................................................................................. Pag.8
A3.3.1 NON USA MODULAR RACK TYPES............................................... Pag.8A3.3.2 USA MODULAR AND COMPACT SHORT RACK TYPES ............... Pag.9
A4 SERVICE MENU ............................................................................................................. Pag.10A4.1 PARAMETERS.................................................................................................... Pag.10
A4.1.1 USER SETTINGS (ONLY FOR MODULAR RACK TYPE NO USA) Pag.10A4.1.2 GENERIC FUNC............................................................................... Pag.11A4.1.3 RINSE MODULE............................................................................... Pag.19A4.1.4 WASH MODULE ............................................................................... Pag.20A4.1.5 PREWASH MODULE........................................................................ Pag.22A4.1.6 DT MODULE..................................................................................... Pag.24A4.1.7 HACCP ............................................................................................. Pag.26A4.1.8 RATING PLATE (ONLY FOR MODULAR RACK TYPE NON USA) . Pag.27
A4.2 DATALOG (ONLY FOR MODULAR RACK TYPE NON USA)............................. Pag.28A4.3 INFO.................................................................................................................... Pag.33A4.4 STATISTICS (ONLY FOR MODULAR RACK TYPE NON USA) ......................... Pag.33A4.5 RINSE CONTROL ( JUST FOR ATMOSPHERIC RACK TYPE ) ....................... Pag.34A4.6 KEY MANAGEMENT ( JUST FOR MODULAR RACK TYPE ) ........................... Pag.36A4.7 SENSOR ADJUSTMENT .................................................................................... Pag.36A4.8 MOTOR ADJUSTMENT...................................................................................... Pag.37
B PROGRAMMING SHEETS............................................................................... Pag. 39
B1 SPECIFIC FUNCTIONS .................................................................................................. Pag.65B1.1 SETTING UNIT OF MEASURE IN FAHRENHEIT .............................................. Pag.65B1.2 LANGUAGE SETTING........................................................................................ Pag.65B1.3 “MAX. MOTOR CURR.” PARAMETER ( GCU ) SETTING .................................. Pag.65
C CONNECTORS LAYOUT ................................................................................. Pag. 66
C1 POWER BOARDS CONNECTORS LAYOUT ................................................................. Pag.66C2 MULTICONNECTOR BOARDS CONNECTORS LAYOUT ............................................. Pag.70C3 CONNECTORS LAYOUT LEGEND ................................................................................ Pag.83C4 END LIMIT SWITCH, ENERGY PEAK CONTROL AND EMERGENCY SWITCH
CONNECTIONSPag........................................................................................................ 83
C4.1 MODULAR (NO USA) ......................................................................................... Pag. 83C4.1.1 END LIMIT SWITCH CONNECTION................................................ Pag. 83C4.1.2 EMERGENCY SWITCH CONNECTION........................................... Pag. 83C4.1.3 ENERGY PEAK CONTROL CONNECTION..................................... Pag. 84
C4.2 USA MODULAR AND COMPACT SHORT ......................................................... Pag. 84C4.3 USA COMPACT .................................................................................................. Pag. 85
C4.3.1 END LIMIT SWITCH CONNECTION................................................ Pag. 85C4.3.2 EMERGENCY SWITCH CONNECTION........................................... Pag. 85C4.3.3 ENERGY PEAK CONTROL CONNECTION..................................... Pag. 85
O. 5956.573.04 P. 2 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
D INVERTER PARAMETERS.............................................................................. Pag. 86
D1 INVERTER PROGRAMMING ......................................................................................... Pag.86D1.1 DISPLAY FUNCTIONS........................................................................................ Pag.86D1.2 INVERTER CONTROL TERMINAL ELECTRICAL CONNECTIONS.................. Pag.87D1.3 INVERTER PARAMETER LISTS ........................................................................ Pag.87
E WARNING MESSAGES AND TROUBLESHOOTING..................................... Pag.90
F MODULE COMPOSITION FOR RACK TYPE.................................................. Pag.94
G FLOWCHARTS FOR TROUBLESHOOTING .................................................. Pag.95
INDEX OF FIGURES AND TABLESFigure 1 Menu access keys.............................................................................................................. Pag.4
Figure 2 Accessing current, temperatures and levels display mode................................................ Pag.4
Figure 3 Accessing the USER MENU .............................................................................................. Pag.6
Figure 4 Accessing the SERVICE MENU ........................................................................................ Pag.6
Figure 5 Parameter and function access menu chart for Modular Rack Type (no USA).................. Pag.6
Figure 6 Parameter and function access menu chart for Compact Short Rack Type and USAModular versions ................................................................................................................ Pag.6
Figure 7 Parameter and function access menu chart for Compact USA Rack Type........................ Pag.7
Figure 8 Scheme for “Heat two comm.” parameter and “Heating manage” parameter (only forModular Rack Type) ........................................................................................................... Pag.15
Figure 9 Scheme for “H2C” parameter and “b_t” parameter (only for Compact Rack Type)............ Pag.15
Figure 10 Electrical connection .......................................................................................................... Pag.83
Figure 11 Detail of electrical connection ............................................................................................ Pag.83
Figura 12 ENERGY PEAK CONTROL CONNECTION...................................................................... Pag.84
Figura 13 USA MODULAR AND COMPACT SHORT CONNECTIONS ............................................ Pag.84
Figura 14 END LIMIT SWITCH AND EMERGENCY SWITCH CONNECTION................................. Pag.85
Figure 15 ENERGY PEAK CONTROL CONNECTION...................................................................... Pag.85
Figure 16 COMPACT RT Inverter electrical connection..................................................................... Pag.87
Figure 17 MODULAR RT Inverter electrical connection..................................................................... Pag.87
Table 1 Work stages/Boiler set point .............................................................................................. Pag.20
Table 2 Machine codes list and relative programming sheets ........................................................ Pag.40
N.B.: The red text of the document indicate additions with respect to the previous edition.
O. 5956.573.04 P. 3 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
A FUNCTION KEYSBUTTONS USED
Figure 1 Menu access keys
A1 DISPLAY OF AUXILIARY VALUES
From the normal machine operation mode it is possible to see several screens not accessible to the user.These screens give various machine values, and are accessed by pressing at the same time the combina-tions of buttons displayed. (Figure 2).
A1.1 MODULAR MACHINES (NO USA)
Press the Speed1 - “E” (Figure 1) - and Increase buttons - “A” (Figure 1) - at the same time for a few secondsto access the screen displaying the levels of the various tanks and airgap.
Figure 2 Accessing current, temperatures and levels display mode
A B C D
U
E
U
U
Prewash 200 mmH2O
Wash 195 mmH2O
Airgap 60 mmH2O
DUO 55 mmH2O
O. 5956.573.04 P. 4 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
Press the Increase button - “A” (Figure 1) - to access the screen giving the current absorbed by the gearmotor.
To return to the standard display, wait 30 seconds or press the Confirm button - “C” (Figure 1) -.
A1.2 COMPACT MACHINES AND USA MODULAR VERSIONS
Press the Speed1 button - “E” (Figure 1) - and Accessory Functions button - ”D” (Figure 1) - at the same timefor a few seconds to access the first screen; press the Increase button - “A” (Figure 1) - to access the subse-quent screens. The following screens are displayed ( in order) :
To return to the standard display, wait 30 seconds or press the Confirm button - “C” (Figure 1) -.
DT temperature(significant only
for machines with DT)
Temperature of first boiler(significant only for
compact USA machines with 2 boilers)
Air Gap level(significant only for
atmospheric machines)
Wash tank level
Prewash tank level(significant only for
machines with prewash)
Duo tank level (significant for USA modular
versions only)
Gear motor current
Mot. Curr. 35 decA
Adttmp68
1 b_Utmp138
2 AIGLE 60
3 tAnLE198
4
sCpLE204
5 dUOLE 45
6 MotCur 34
7
O. 5956.573.04 P. 5 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
A2 ACCESSING THE USER MENU AND SERVICE MENU
From normal machine operation mode all the parameters and information can be accessed for programmingthe electronic boards by pressing the combinations of keys displayed in (Figure 3) and in (Figure 4).
From the USER MENU and SERVICE MENU it is possible to access the following parameter families and infor-mation see (Figure 5) and (Figure 6) using the increase (“A” - (Figure 1)) and decrease (“B” - (Figure 1)) keysto select the object, the confirm key (“C” - (Figure 1)) to access the selected object and the accessory functionskey (“D” - (Figure 1)) to exit the object.
Figure 5 Parameter and function access menu chart for Modular Rack Type (no USA)
Figure 6 Parameter and function access menu chart for Compact Short Rack Type and USA Modular versions
Figure 3 Accessing the USER MENU Figure 4 Accessing the SERVICE MENU
U
U
UU
UU
USER MENU SERVICE MENU
EXIT
USERSETTINGS
GENERIC FUNC. RINSEMODULE
WASHMODULE
PREWASHMODULE
DTMODULE
DATA SETTING CONSUMPTION PARAMETERS DATALOG INFO STATISTICS RINSE CONTROL KEY MANAGEM. SENS. ADJUST.
HACCP RATING PLATE
MOTOR ADJUST.
FAC (SERVICE MENU)USr (USER MENU)
PAr(PARAMETERS) rfC(RINSE CONTROL) SAd(SENSOR ADJUST.) GAd(MOTOR ADJUST.)Inf(INFO)ESC(EXIT) Con(CONSUMPTION)
GFu(GENERIC
FUNC.)
RiN(RINSE
MODULE)
tub(WASH
MODULE)
pRE(PREWASHMODULE)
Dt(DT MODULE)
HAC(HACCP)
O. 5956.573.04 P. 6 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
Figure 7 Parameter and function access menu chart for Compact USA Rack Type
A3 USER MENU (NOT AVAILABLE FOR USA COMPACT RACK TYPES)
Press the accessory functions keys (“D” - (Figure 1)) and the increase key (“A” - (Figure 1)) at the same timefor several seconds to access the USER MENU.
The current date and time used in recording events (see par. A4.2 DATALOG (ONLY FOR MODULAR RACKTYPE NON USA)) and statistics (see A4.4 STATISTICS (ONLY FOR MODULAR RACK TYPE NON USA))can be set inside the USER MENU.
WARNING:
At first machine start-up make sure the date and time are correctly set.
Display the number of racks processed by the machine and machine consumption.The various USER MENU items can be selected by using the increase (“A” - (Figure 1)) and decrease (“B” -(Figure 1)) keys.
A3.1 EXIT
Press the confirm key (“C” - (Figure 1)) when the selection arrow indicates the item EXIT (ESC) to return tonormal machine operation.
A3.2 DATA SETTING (FOR NON USA MODULAR RACK TYPES ONLY)
Press the confirm key (“C” - (Figure 1)) when the selection arrow indicates the item DATA SETTING and thedisplay will show the set date and time:
Press the accessory functions key (“D” - (Figure 1)) to display the USER MENU again. To modify the set date,select the date with the increase (“A” - (Figure 1)) and decrease (“B” - (Figure 1)) keys and press the confirmkey (“C” - (Figure 1)).
FAC (SERVICE MENU)
PAr(PARAMETERS) rfC(RINSE CONTROL) SAd(SENSOR ADJUST.) GAd(MOTOR ADJUST.)Inf(INFO)
GFu(GENERIC
FUNC.)
RiN(RINSE
MODULE)
tub(WASH
MODULE)
pRE(PREWASHMODULE)
Dt(DT MODULE)
HAC(HACCP)
USER MENU
1 - EXIT2 - DATA SETTING
123 USr
ESC
DATE & TIME
09 NOV 05 14 : 25
O. 5956.573.04 P. 7 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
The display shows the current date at the bottom and the date being set at the top.
Use the increase, decrease and confirm keys to modify the date.
To modify the set time, select the time with the increase and decrease keys and press the confirm key.The display shows the current time at the bottom and the time being set at the top.
Use the increase, decrease and confirm keys to modify the time.
A3.3 CONSUMPTION
A3.3.1 NON USA MODULAR RACK TYPES
Press the confirm button (“C” - (Figure 1)) when the selection arrow indicates the item CONSUMPTION andthe display will show the counter of the racks processed by the machine.
The display shows the number of racks starting from the date of machine installation. The number of racksprocessed, counted starting from the date indicated opposite, corresponding to the last reset (RESET CONS)is also displayed.In fact the rack counter can be reset by pressing the confirm button; in this way the “CONSUMPTION RESET”mode is accessed.
Press the confirm button again to reset the resettable rack counter.The rack counter is reset and the date and time of the last reset are saved.If the last counter reset occurred in the factory, the message FAC appears next to the reset time.Press the additional functions button to exit the “CONSUMPTION RESET” mode.Use the increase and decrease buttons to display the screens relevant to:- rinse module water consumption (litres)- wash module water consumption (litres)- prewash module water consumption (litres)- machine power input (kwatt/h)
SET DATE
09 NOV 0509 NOV 05
12MAY
SET TIME
15 : 25 : 32 14 : 25 : 32
CONSUMPT.BASKETS NUMBER
0RESET CONS DD-MM-YY HH:MM 0 02-11-00 10:25 FAC
CONSUMPT. RESETBASKETS NUMBER
0RESET CONS DD-MM-YY HH:MM 0 02-11-00 10:25 FAC
O. 5956.573.04 P. 8 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WARNING:
To have the above information the machine must be equipped with suitable flow meters (water con-sumption) and/or a suitable energy measurer and the Pulse/lit rinse, Pulse/lit wash, Pulse/lit pre-wash, Pulse/kWattH parameters must be correctly set.
Also these screens provide for 2 counters, one resettable and the other non-resettable, usable as describedabove.
A3.3.2 USA MODULAR AND COMPACT SHORT RACK TYPES
Press the confirm button (“C” - (Figure 1)) when the item Con (CONSUMPTION) is selected, and the displaywill show the counter of racks processed by the machine.
The number of racks processed and the item to which the number shown refers are displayed alternately. Toobtain the total number of processed racks, form the numbers displayed as follows:
number of racks = 2059165
The display shows the number of racks starting from the date of machine installation. The number of racksprocessed starting from a reset operation can also be displayed.In fact, the rack counter can be reset by pressing the confirm button; in this way the “CONSUMPTIONRESET” mode is accessed.
Press the confirm button again to reset the resettable rack counter. The rack counter is reset.Press the additional functions button to exit “CONSUMPTION RESET”mode.Use the increase and decrease buttons to display the screens relevant to:- rinse module water consumption (litres)- wash module water consumption (litres)- prewash module water consumption (litres)
WARNING:
To have the above information the machine must be equipped with suitable flow meters (water con-sumption) and the PLr, PLt, PLP parameters must be correctly set.
Also these screens provide for 2 counters, one resettable and the other non-resettable, usable as describedabove.
itEnbr
0 0168
2059165
rESitEnbr
0 0 20
O. 5956.573.04 P. 9 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
A4 SERVICE MENU
Press the accessory functions key (“D” - (Figure 1)) and the decrease key (“B” - (Figure 1)) at the same timefor several seconds to access the SERVICE MENU.
Inside the SERVICE MENU it is possible to:• display and edit all the machine parameters;• access the DATALOG, i.e. a file of events that occurred during machine operation (only for modular rack
type);• display information of a general nature, such as the machine software versions;• consult a file of statistics relevant to the various machine load activation times and starts (only for modular
rack type).• adjust the rinse flowrate cock ( just for atmospheric rack type).• Save the parameters, datalog content and content of the statistics in a removable
backup memory (for modular RT's only).• Set the pressure sensors that detect the levels of the airgap, Duo rinse tank, wash tank and prewash tank.• Carry out feed gear motor current setting.
WARNING:
After entering the SERVICE MENU switch the machine off and then on again to return to normal opera-tion.
The various SERVICE MENU items can be selected by using the increase (“A” - (Figure 1)) and decrease (“B”- (Figure 1)) keys.
A4.1 PARAMETERS
Press the confirm key (“C” - (Figure 1)) when the arrow indicates the PARAMETERS item and the display willshow the first family of parameters.
A4.1.1 USER SETTINGS (ONLY FOR MODULAR RACK TYPE NO USA)
The USER SETTINGS family contains parameters for setting the user interface.
Use the increase and decrease keys to select the other parameter families.Press the accessory functions key (“D” - (Figure 1)) to display the SERVICE MENU again.
MODULAR RACK TYPE COMPACT RACK TYPE AND USA MODULAR
SERVICE MENU
1 - PARAMETERS2 - DATALOG
123
USER SETTINGS
O. 5956.573.04 P. 10 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
Press the confirm key (“C” - (Figure 1)) to access the first parameter of the USER SETTINGS family.
Press the accessory functions key (“D” - (Figure 1)) to display the USER SETTINGS family again. Use the increase and decrease keys to select the other parameters of the USER SETTINGS family.Press the confirm key to edit the selected parameter; the selection arrow moves from the parameter name tothe parameter value.
Use the increase and decrease keys to modify the parameter value. Press the confirm key to save the newset value. Press the accessory functions key to exit without saving the new setting. The USER SETTINGS family parameters are described below:
Available languages: ENGLISH, ITALIAN, GERMAN, FRENCH, SPANISH, PORTUGUESE, DUTCH, DAN-ISH, NORWEGIAN, SWEDISH, FINNISH, GREEK, RUSSIAN, ESTONIAN, LATVIAN, LITHUANIAN,POLISH, CZECH, HUNGARIAN, SLOVAK, SLOVENIAN, TURKISH.
A4.1.2 GENERIC FUNC.
The GENERIC FUNC. family parameters are selected and edited by using the keys in the same way as thatdescribed for the USER SETTINGS family.The GENERIC FUNC. family contains parameters that identify several general machine characteristics.
Parameter name
FamilyNr.
ParameterNr.
Parameter description Unit of measure
Min Max Factory setting
Language 0 0 Allows setting of required language - - - EnglishContrast 0 1 Allows setting of screen contrast - 0 5 3
MODULAR RACK TYPE COMPACT RACK TYPE AND USA MODULAR
USER SETTINGS
Language
ENGLISH
USER SETTINGS
Language
ENGLISH
GENERIC FUNC.
O. 5956.573.04 P. 11 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
The GENERIC FUNC. family parameters are described below:
(*) For the other equipment families, see par. B PROGRAMMING SHEETS
Modular parameter
Compact paramet
er
FamilyNr.
Parameter Nr.
Parameter description Unit of
measure
Min Max Factory setting [for WTM165 (*)]
Appl. type APt 1 0 Machine type for modular rack type:0/Ws Ri : 2 modules rinse and wash.1/Pw Ws Ri : 3 modules rinse, wash and prewash.2/Pw Ws Ri Dt: 4 modules rinse, wash, prewashand DT.3/Ws Ri Dt: 3 modules rinse, wash and DT.
- - - Ri Ws (0)
Machine type for compact rack type:4: Compact pressurized plumbing circuit5: Compact atmospheric plumbing circuit6: Compact pressurized plumbing circuit with dt7: Compact atmospheric plumbing circuit with dt8: Compact pressurized plumbing circuit withprewash9: Compact atmospheric plumbing circuit withprewash10: Compact pressurized plumbing circuit withprewash and dt11: Compact atmospheric plumbing circuit withprewash and dt12: Compact Usa13: Compact Usa with DT14: Compact Usa with prewash15: Compact Usa with prewash and DT
- - -
Appl. direct.
Ad 1 1 Rack pulling direction (meaningful parameter onlyfor Modular Rack Type NO USA):1/LEFT: left rack insertion.0/RIGHT: right rack insertion.
- RIGHT(0)
LEFT(1)
RIGHT(0)
Speed nr. 1
SP1 1 2 Indicates gear motor operation frequency at speed1.
Hz 15 100 27 (**)
Wash time sp 1
rd1 1 3 Time from when the last rack releases the autostart lever until the wash pumps stop when speed 1is set
sec 0 127 110
Speed nr. 2
SP2 1 4 Indicates gear motor operation frequency at speed2.
Hz 15 100 51 (**)
Wash time sp 2
rd2 1 5 Time from when the last rack releases the autostart lever until the wash pumps stop when speed 2is set.
sec 0 250 58
(**) Modular machine type WTM140 WTM165 WTM180 WTM200 WTM250 WTM300 WT82 WT105
(***) Racks/h Speed nr. 1 80 90 110 130 160 180 250 250
Speed nr. 1 25 27 35 40 53 60 70 70
Racks/h Speed nr. 2 140 165 180 200 250 300 350 350
Speed nr. 2 45 51 58 63 83 100 100 100
(**) Compact machine type RTCS90 / WTCS90
RTCS140 / WTCS140
RTCS180 / WTCS180
RTCS250 / WTCS250
WT44 WT66
(***) Racks/h Speed nr. 1 90 90 120 180 100 100
Speed nr. 1 27 27 35 57 31 31Racks/h Speed nr. 2 90 140 180 250 200 200
Speed nr. 2 27 45 58 80 63 63
(***) To comply with Standard DIN 10510 it is advisable to use speed nr. 1
O. 5956.573.04 P. 12 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
Modular parameter
Compact parameter
FamilyNr.
ParameterNr.
Parameter description Unit of
measure
Min Max Factory setting [for WTM165 (*)]
Clean duration
dCd 1 11 Duration of wash phase during self-clean cycle.The self-cleaning cycle is carried out with the followingsteps:1. complete emptying of tanks;2. partial filling of tanks;3. 3 washes of duration set in the “Clean duration”
parameter, separated by two 5-second pauses;4. complete emptying of tanks and air gap.
sec 0 100 15
Drain enable
drE 1 16 Enabling of drain and self-clean cycles:0: All the drain and self-clean cycles are disabled.1: Enables the drain cycle of all tanks in theequipment.5: Enables the drain cycle of all tanks in the equipmentand only the drain cycle for the wash tank.7: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank andonly the drain cycle for the prewash tank.13: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank andonly the drain cycle for the DUO rinse tank.15: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank, onlythe drain cycle for the prewash tank and only the draincycle for the DUO rinse tank.21: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank andthe drain cycle for the air gap.23: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank, onlythe drain cycle for the prewash tank and the draincycle for the air gap.29: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank, onlythe drain cycle for the DUO rinse tank and the draincycle for the air gap.31: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank, onlythe drain cycle for the prewash tank, only the draincycle for the DUO rinse tank and the drain cycle for theair gap.33: Enables the drain cycle of all tanks in theequipment and the self-clean cycle.37: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tankand the self-clean cycle.39: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank,only the drain cycle for the prewash tank and theself-clean cycle.45: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank, onlythe drain cycle for the DUO rinse tank and the self-clean cycle.47: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank, onlythe drain cycle for the prewash tank, only the draincycle for the DUO rinse tank and the self-clean cycle.49: Enables the drain cycle of all tanks in theequipment and the self-clean cycle and the drain cyclefor the air gap.53: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tankand the self-clean cycle and the drain cycle for theair gap.55: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank,only the drain cycle for the prewash tank, the self-clean cycle and the drain cycle for the air gap.61: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank,only the drain cycle for the DUO rinse tank, theself-clean cycle and the drain cycle for the air gap.63: Enables the drain cycle of all tanks in theequipment, only the drain cycle for the wash tank,only the drain cycle for the prewash tank, only thedrain cycle for the DUO rinse tank, the self-cleancycle and the drain cycle for the air gap.
- 0 63 61
O. 5956.573.04 P. 13 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
.
Modular parameter
Compact parameter
FamilyNr.
Parameter
Nr.
Parameter description Unit of
measure
Min Max Factory setting
[for WTM165
(*)]
Heat two comm.
H2C 1 18 Modular Rack Type:Wash tank heating element management mode; if seton “Yes” (1) the two heating elements are managed bytwo separate controls, otherwise they are managed bya single control (See Figure 8 Scheme for “Heat twocomm.” parameter and “Heating manage”parameter (only for Modular Rack Type)).
- No (0)
Yes(1)
Yes (1)
Compact Rack Type:the mode “1” is not available on compact machines.
- 0 1 1
Heating manage
B_t 1 19 Machine heating power management.Maximum power: the wash tank heating elementsand the boiler heating elements can operate at thesame time.
WARNING:
Check the electrical system and safetydevices ahead of the equipment before set-ting “Max. power” mode
Medium power: when the boiler heating elements areon, only one of the two wash tank heating elementscan operate; during the warmup, the tank is heatedfirst and then the boiler, whereas the boiler has priorityduring normal operation.
Minimum power: the wash tank heating elementscannot operate when the boiler heating elements areon; during the warmup, the tank is heated first andthen the boiler, whereas the boiler has priority duringnormal operation (See Figure 8 Scheme for “Heattwo comm.” parameter and “Heating manage”parameter (only for Modular Rack Type) andFigure 9 Scheme for “H2C” parameter and “b_t”parameter (only for Compact Rack Type)).Modular Rack Type:0/“HIGH” = Maximum power2/“MEDIUM” = Medium power1/“LOW” = Minimum power
WARNING:
THIS CONFIGURATION CAN ONLY WORKON ELECTRICALLY ARRANGED MACHINESAND THE “Heat two comm.” PARAMETERMUST BE SET ON “Yes”.
The machines electrically arranged to operate in“MEDIUM” mode are the WTM165, WTM200, WT82and WT105 models.
- HIGH(0)
MEDIUM(2)
MEDIUM(2)
Compact Rack Type:“0” = Maximum power“2” = Medium power“1” = Minimum power
WARNING:
THIS CONFIGURATION “2” CAN NOT BEIMPLEMENTED IN THE ACTUAL VERSIONSOF COMPACT RACK TYPE.
- 0 2 2
O. 5956.573.04 P. 14 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
Figure 8 Scheme for “Heat two comm.” parameter and “Heating manage” parameter (only for Modular Rack Type)
Figure 9 Scheme for “H2C” parameter and “b_t” parameter (only for Compact Rack Type)
SINGLECONTACTOR
DOUBLECONTACTOR
HARDWARE MACHINECONFIGURATION
MEDIUM
HIGH
LOW
HIGH
LOW
Heat two comm. Heating manage
SINGLECONTACTOR
HARDWARE MACHINECONFIGURATION
0
1
b_tH2C
(Maximum Power)
(Minimum Power)
O. 5956.573.04 P. 15 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
Modular parameter
Compact parameter
FamilyNr.
Parameter
Nr.
Parameter description Unit of measure
Min Max Factory setting
[for WTM165
(*)]
Boiler load tank
btF 1 20 Modular Rack Type:Wash tank filling mode: the tank is filled by means ofa dedicated solenoid valve.
- No (0)
Yes (1)
No(0)
Standard Compact Rack Type (old range):Wash tank filling mode: the tank is filled by means ofthe rinse arms.
- 0 1 1
Short Compact Rack Type (new range):Wash tank filling mode: the tank is filled by means ofa dedicated solenoid valve.
- 0 1 0
Sanit. enable
SnE 1 22 Enables sanitization cycle (N.B.: A heating elementmust be installed in the prewash module if present).The sanitising cycle consists of the following stages:1. compete emptying of the tanks and air gap;2. partial filling of the wash and prewash tanks;3. heating of wash tank water up to the temperature
set in the “WASH MODULE” “Sanit temper”family parameter;
4. WASH module sanitising; the duration of thisstage is set in the “WASH MODULE” “washsan.duration” family parameter;
5. wash tank emptying and prewash water heatingup to the temperature set in the “PREWASHMODULE” “Sanit temper” family parameter;
6. PREWASH module sanitising; the duration ofthis stage is set in the “PREWASH MODULE”“prewash san.duration” family parameter;
7. prewash tank emptying.Modular Rack Type:- 0/ “No” sanitization cycle disable- 1/“Yes” sanitization cycle enable.
- No (0)
Yes (1)
No (0)
Compact Rack Type:“0” sanitization cycle disable“1” sanitization cycle enable.
- 0 1 0
Heat pump
HP 1 23 Enables heat pump management.The heat pump contains 1050 g of R134a refrigerantliquid in its hydraulic circuit.Modular Rack Type:- 0/“No” heat pump management disable- 1/“Yes” heat pump management enable.
- No (0)
Yes (1)
No(0)
Compact Rack Type:“0” heat pump management disable“1” heat pump management enable.
- 0 1 0
Fahrenheit vis.
CF 1 28 Unit of measure used in displaying temperatures; ifset on “Yes” the temperature is displayed in degreesFahrenheit, otherwise in degrees Celsius.Modular Rack Type:“No” the temperature is displayed in degrees Celsius“Yes” the temperature is displayed in degreesFahrenheit.
- No (0)
Yes (1)
No(0)
Compact Rack Type:“0” the temperature is displayed in degrees Celsius“1” the temperature is displayed in degreesFahrenheit.
- 0 1 0
O. 5956.573.04 P. 16 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
(*) For the other equipment families, see par. B PROGRAMMING SHEETS.
** The table given below indicates the delay between transit of the rack on the autorinse lever and stopping ofthe rinse phase.E.g. in a WTM165 working at high speed (165 racks/h) the rinse pump keeps operating for 11 seconds afterthe last rack has released the autorinse lever.
Modular parameter
Compact parameter
FamilyNr.
Parameter
Nr.
Parameter description Unit of measure
Min Max Factory setting
[for WTM165
(*)]
Buzzer enabled.
buE 1 29 Enables machine buzzer.Modular Rack Type:- 0/“No” machine buzzer disable- 1/“Yes” machine buzzer enable.
- No (0)
Yes (1)
Yes(1)
Compact Rack Type:- “0” machine buzzer disable- “1” machine buzzer enable.
- 0 1 0
Demo mode
dMo 1 30 Demo mode.Modular Rack Type:- 0/“No demo” normal operation.- 1/“Demo mec” the users are not activated and the inputs are not read, but communication between the USER card and POWER cards is maintained .- 2/“Demo user” the users are not activated, theinputs are not read, the USER card doesn’t communicate with the POWER cards.
- - - No demo(0)
Compact Rack Type:- “0” normal dishwasher operation.- “1” the users are not activated and the inputs are not read, but communication between the USER card and POWER cards is maintained .- “2” not available on these models.
- - - 0
Rinse autostart.
r_A 1 31 Indicates the type of command for the start of therinse phase. It can be set to “Mechanical” (1) only ifthe special mechanical lever is present in the rinsezone. **
Software/0
Mechanical/1
Software/0
Max. motor
curr.***GCU *** 1 32 Indicates the max. current deliverable to the gear
motor by the inverter if the automatic gear motorcurrent setting procedure was not carried out.
If the supplied current is higher than this value,themessage “CROCKERY STUCK” appears on modularRack Type no USA and the message “ SEE ITEMINSIDE” on compact Rack Type e modulari USA.
decAmp.
0-
40-
35(110Vac
gearmotor)
0(230Vac
gearmotor)
Set default
par.
spd 1 33 It allows all the parameters to be set to their defaultvalue. The set parameters are those of a WTM165without DT.The parameter set to “Yes” (1) automatically returnsto “No” (0).
- No/ 0
Yes/ 1
No/ 0
O. 5956.573.04 P. 17 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
In compact machines the rinse is active while the auto rinse lever is activated, without any delay.
*** Procedure for manually setting the “Max. motor curr.” parameter:1. Wait until the machine, complete with tables, is ready for a wash cycle.2. Start a wash cycle without putting racks in the machine and read the current absorbed by the gearmotor ( refer to par. A1 DISPLAY OF AUXILIARY VALUES).3. Add 2 to the read value (e.g. if “Motor current” = 34 ---> 34+2=36 decA).4. Set the “Max. motor curr.” parameter with the value thus obtained.
WARNING:
The Rack Type leaves the factory with the “Max motor curr.” parameter already set to the optimumvalue. Reset it only when replacing a PCB or the gear motor.
Speed nr. 1 (Hz)
Capacity speed nr. 1 (racks/hour)
Delay speed nr. 1 (sec)
Speed nr. 2 (Hz)
Capacity speed nr. 2 (racks/hour)
Delay speed nr. 2 (sec)
WTM140 25 80 22 45 140 12WTM165 27 90 20 51 165 11WTM180 35 110 15 59 180 9WTM200 40 130 13 63 200 9WTM250 53 160 10 83 250 6WTM300 60 180 9 100 300 5
WT82 70 250 25 100 350 17WT105 70 250 52 100 350 38
Modular parameter
Compact parameter
FamilyNr.
ParameterNr.
Parameter description Unit of meas-
ure
Min Max Factory set-ting [forWTM165 (*)]
Feeding delay
FdI 1 34 Indicates the time (min) from when the lastbasket is placed in the machine until thefeed stops and the machine goes from“WAITING FOR A BASKET” status to“READY”.
min 0 60 25
Pulse/kWatt
EnP(not significant
for USA modular and
compact machines)
1 35 Indicates the impulses per kilowatt/hourcharacterising the possible energy meterconnected to the machine’s power cable.Rating data of the energy measurer used.
P/kWh 0 999 0
Nsf settings
nSF 1 36 Sets the machine temperature in conformitywith NSF regulations:Wash tank temperature: 78°CWash tank temperature hysteresis: 0°CDuo rinse temperature: 78°CDuo rinse temperature hysteresis: 2°CIf the parameter is set to “No”, the defaulttemperatures are set
- No(0)
Yes(1)
No(0)
Mot. curr. margin
GCM 1 37 Indicates the margin, expressed in tenths ofamperes, between the current absorbed bythe gearmotor at the various speeds and thevalue which, if reached, blocks the machinewith display of the message “DISHESJAMMED” on non-USA modular RT’s and“SEE itEM inSIdE” on USA modular andcompact RT’s.Significant only if the gearmotor current wasset with the “MOTOR ADJUST” procedure.
dec Amp
0 5 2
O. 5956.573.04 P. 18 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
A4.1.3 RINSE MODULE
The RINSE MODULE family parameters are selected and edited by using the keys in the same way as thatdescribed for the USER SETTINGS family. The RINSE MODULE family contains the parameters that identify the rinse module characteristics.
The RINSE MODULE / rin family parameters are described below:
MODULAR RACK TYPE COMPACT RACK TYPE AND USA MODULAR
Modular parameter
Compact parameter
FamilyNr.
ParameterNr.
Parameter description Unit of measure
Min Max Factory setting
Max. lev. airgap(*)
ASL(*) 2 0 Max water level in air gap. mmH2O 30 100 80
Max hist. airgap(*)
ASH(*) 2 1 Hysteresis level relative to max level in the air gap. mmH2O 0 80 30
Work lev. airgap(*)
AnL(*) 2 2 Water level in the air gap enabling rinse pumpoperation.
mmH2O 0 100 40
Max. lev. duo (**)
dSL(**)(meaningless for compact
family)
2 4 Indicates the maximum level in the Duo rinse tank.The filling stops when the water level reaches thisvalue.
mmH2O 30 100 55
Dm max duo lev.
(**)
dSd(**)(meaningless for compact
family)
2 5 Meaningful only during ““Drain and clean” cycle.Indicates the maximum level during “Drain andclean” cycle.
mmH2O 10 100 45
Max hist. duo (**)
dSH(**)(meaningless for compact
family)
2 6 Indicates the hysteresis level relative to themaximum level in the Duo tank.It is related to the “Max. lev. duo” and to the “Dmmax duo lev.”.
mmH2O 0 80 10
Work lev. duo (**)
dnL(**)(meaningless for compact
family)
2 7 Indicates the water level in the the Duo tankenabling the Duo heating element and the Duopump operations.
mmH2O 0 50 30
Boil. temp. start
btS 2 9 Boiler temperature set point at start of rinse phase;the initial overtemperature determined by thisparameter ensures that the introduction of coldwater in the boiler does not lower the rinse watertemperature at the start of rinsing.
°C / °F 10/50
99/210
92/198
Boiler temper.
bot 2 10 Boiler temperature set point. °C / °F 10/50
99/210
86/187
Boil temp. wmup
bti 2 11 Boiler warm-up temperature. During warm-up, theboiler temperature is brought to the parametervalue, after which the boiler does not heat until thestart of the wash stage.It is advisable to set the Boil temp. warm-upparameter (bti) as follows:- electric machines bti = bot- steam machines bti < bot.
°C / °F 10/50
99/210
86/187
Hist. boil temp.
btH 2 12 Hysteresis temperature relative to boilertemperature set point.
°C / °F 0/0 15/27
0/0
Standby Delta T
btd 2 13 When the machine is in standby mode, the waterinside the boiler is kept at a temperature ofbot-btd (It is used to save energy whenthe machine is not in use; the boiler is kept at alower temperature).
°C / °F 0/0 70/126
5/9
Active threshold
ACt(meaningless for compact SHORT and USA modular
versions)
2 13 Indicates the temperature that determines thecolour of the active LED (red/green).If the rinse temperature stays below the set valuefor more than 2 minutes the LED turns red,otherwise it is green.Setting the parameter to 0 disables the active LED(it remains off).
°C / °F 0/32 99/210
75/167
RINSE MODULE
O. 5956.573.04 P. 19 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
Table 1 Work stages/Boiler set point
A4.1.4 WASH MODULE
The WASH MODULE family parameters are selected and edited by using the keys in the same way as thatdescribed for the USER SETTINGS family.
First boil. temp.
Fbt 2 15 First boiler temperature set point.( Significant only for USA machines with 2 boilers).Set to 0°C (32°F) USA compact machines withoutboiler.
°C / °F 0/32 99/210
59/138
First boil. hist.
FbH 2 16 Hysteresis temperature relative to first boilertemperature set point.( Significant only for USA machines with 2 boilers).
°C / °F 0/0 15/27
0/0
Duo temper.
dut 2 17 DUO rinse tank temperature set point. °C / °F 5/41 95/203
70/158
Hist. duo temp.
dtH 2 18 Hysteresis temperature relative to DUO rinse tanktemperature set point.
°C / °F 0/0 50/90
5/9
Drain del. airgap
Add 2 20 Time between reaching level “0” (air trap level) inthe air gap and stop of rinse pump (during thedraining cycle).
sec 0 200 32
Drain delay duo
ddd 2 22 Time between reaching level “0” (air trap level) inthe DUO rinse tank and closing of the drainsolenoid valve; allows complete emptying of tank(during the draining cycle).
sec 0 200 30
Heat. tim. enable
HtE 2 23 Allows enabling/disabling of the boiler heatingTime out alarm ( alarm 15).If the parameter is set to “No” (0), the alarm 15 ismanaged as a warning and does not shut downthe machine even if the boiler never reaches thetemperature set point.
- No/ 0
Yes/ 1
Yes/ 1
Duo heat. unrel.
dHU 2 24 Allows the Duo heating element operation to befreed from that of the other heating elements. If setto “Yes” (1) the Duo heating element can switchon even if the tank and boiler heating elements areon.
WARNING:
Check the electrical system and thesafety devices ahead of the equipmentbefore setting “Yes”.
- No/ 0
Yes/ 1
No/ 0
Airgap area
AAG 2 25 Defines the base area of the airgap. This value isused in the “Rinse control” procedure.
cmq 500 999 700
Pulse/lit rinse
PLr 2 26 Indicates the impulses per litre characterising thepossible flow meter connected to the rinse modulefeed.Rating of the flow meter used.
P/Lit 0 999 0
(*) The difference between the max. water level and the hysteresis level must be higher than the work hysteresis airgap. Max. lev. airgap - Max. hist. airgap Work hist. airgap ASL - ASH > AnL(**) The difference between the max. water level and the hysteresis level must be higher than the working level: Max. lev. duo - Max. hist. duo > Work lev. duo dSL - dSH > dnL(**) The difference between the max. water level during drain cycle and the hysteresis level must be higher than the working level: Dm max duo lev. - Max. hist. duo > Work lev. duo dSd - dSH > dnL
WORK STAGES SET POINT BOILER
Rack removal wait "Boiler temp."Warmup stage in progress "Boil temp. Wmup"Machine ready for wash "Boiler temp." - "Standby Delta T"Wash in progress "Boiler temp." ("Start Boil. Temp.” at start of rinse)Rack wait "Boiler temp."Cycle unload/unload & cleaning ready for execution "Boiler temp." - "Standby Delta T"Cycle unload/unload & cleaning in progress "Boiler temp." - "Standby Delta T"Cycle unload/unload & cleaning finished "Boiler temp." - "Standby Delta T"
O. 5956.573.04 P. 20 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
The WASH MODULE family contains the parameters that identify the wash module characteristics.
The WASH MODULE / tub family parameters are described below:
MODULAR RACK TYPE COMPACT RACK TYPE AND USA MODULAR
Modular parameter
Compact parameter
FamilyNr.
ParameterNr.
Parameter description Unit of measure
Min Max Factory setting
[for WTM165
(*)]
Wash module
tty 3 0 Type of wash moduleModular Rack Type:-0/ “1165” module from 1165 mm-1/ “1490” module from 1490 mm.
- - - 1490
Compact Rack Type:- “2” Wash+Rinse module
- - - 2
Stanby level (**)
tSS(**) 3 1 Indicates the maximum level in the wash tank.The filling stops when the water level reachesthis level.
mmH2O 60 400 205
Run max level (**)
tSr(**) 3 2 The value for the maximum level is modified from“Standby level” to “Run max level” duringwashing phase in order to avoid water loss whenthe pumps stop.
mmH2O 60 400 170
Drain max lev. (**)
tSd(**) 3 3 Meaninful only during “Drain and clean” cycle.Indicates the maximum level during “Drain andclean” cycle.
mmH2O 60 400 190
Max lev. hister. (**)
tSH(**) 3 4 Indicates the hysteresis level relative to themaximum level in the wash tank. It is related tothe “Standby level” to the “Run max level” and tothe “Drain max lev.”.
mmH2O 0 80 30
Working level (**)
tnL(**) 3 5 Indicates the water level in the wash tankenabling the wash tank heating elements and thewash pumps operations.
mmH2O 60 400 90
Tank temper.
tut 3 7 Tank temperature set point. °C / °F 5/41 90/194 66/151
Sanit. temper.
tSt 3 8 Tank temperature set point during thesanitization phase (only on machines withsanitization).
°C / °F 10/50 90/194 75/167
Histesys temp.
ttH 3 9 Hysteresis temperature relative to tanktemperature set point.
°C / °F 0/0 50/90 2/4
Max Temp.
CU
StC 3 10 Max permissible temperature for the waterleaving the CU to enable heat pump operation. Ifthe water leaving the CU exceeds thistemperature, the machine continues to worknormally but the heat pump (if present) stops.
WARNING:
Do not modify this parameter unlessexpressly required by the factory.
°C / °F 1/34 90/194 50/122
Hist. Temp.
CU
HtC 3 11 Max permissible temperature for the waterleaving the CU to enable heat pump operation: ifthe temperature of the water leaving the CU fallsbelow “Max temp. CU - Hist. temp. CU”, themachine continues to work normally but the heatpump (if present) stops.
WARNING:
Do not modify this parameter unlessexpressly required by the factory.
°C / °F 1/2 50/90 20/46
WASH MODULE
O. 5956.573.04 P. 21 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
(*) For the other equipment families, see par. .
(**) The difference between the max water level and the hysteresis level must be higher than the working level:
Stanby level - Max lev. hister > Working level
tSS - tSH > tnl
(**) The difference between the max water level during washing phase and the hysteresis level must be higher than the working level: Run max level - Max lev. hyster. > Working level
tSr - tSH > tnl(**) The difference between the max water level during drain cycle and the hysteresis level must be higher than the working level: Drain max lev. - Max lev. hyster. > Working level
tSd - tSH > tnl
A4.1.5 PREWASH MODULE
The PREWASH MODULE family parameters are selected and edited by using the keys in the same way asthat described for the USER SETTINGS family.The PREWASH MODULE family contains the parameters that identify the prewash module characteristics.
Temp. Thresh.
CU
ttC 3 12 Meaninful only for machines with heat pump.Indicates the CU temperature when the washingtank heating elements stop.This function is enabled only if the heat pump isinstalled and allows maintaining the CUtemperature compatible with the heat pumpfeatures.
°C / °F 20 / 68 70 / 158
48 / 118
Wash san.
duration
Std 3 13 Duration of wash tank cleaning phase during asanitization cycle.
sec 0 250 60
Fan delay start
CGd 3 14 The time between start of wash and start of CUfan ( Parameter not significant for Compact RackType ).
sec 0 200 0
Fan delay stop
CSd 3 15 The time between stop of wash phase and stopof CU fan ( Parameter not significant forCompact Rack Type ).
sec 0 200 20
Drain delay
dtd 3 17 Time between reaching level “0” (air trap level) inthe tank and closing of the drain solenoid valve;allows complete emptying of wash tank
sec 0 200 30
Autom. drain del.
Atd 3 18 Time between two automatic water changes. Ifthis parameter is set at zero the function isdisabled.
min 0 250 120
Water to drain
qtd 3 19 Quantity of water to be drained with eachautomatic emptying.
mmH2O 0 100 25 (***)
Condensing unit
CUn 3 20 CU presence. - No/0 Yes/1 Yes/1
Wash temp. ready
ttr 3 21 Indicates the wash tank temperature thatdetermines the end of warm-up.
°C / °F 5/41 90/194 64/147
Pulse/lit wash
PLt 3 22 Indicates the impulses per litre characterisingthe possible flow meter connected to the washmodule feed.Rating of the flow meter used.
P/Lit 0 999 0
Warning lev wash
Alt 3 23 Indicates the max. level possible in the washtank before the start of an automatic drainingcycle. To prevent water spilling from the door incase of clogging of the overflow due to dirt.
mmH2O 180 400 270
(***) WASH TANKS 1165 mm /44” 1490 mm
Tank capacity 100 l 150 lWater to drain (in litres/mm) 0,32 l/mm 0,485 l/mm
MODULAR RACK TYPE COMPACT RACK TYPE AND USA MODULAR
PREWASH MODULE
O. 5956.573.04 P. 22 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
The PREWASH MODULE / PrE family parameters are described below::
(**) The difference between the max water level and the hysteresis level must be higher than the working level:
Stanby level - Max lev. hister > Working level
SbL - PSH > Pnl(**) The difference between the max water level during washing phase and the hysteresis level must be higher than the working level: Run level - Max lev. hister > Working level
PSS - PSH > Pnl
(**) The difference between the max water level during drain cycle and the hysteresis level must be higher than the working level: Drain max level - Max lev. hister > Working level
PSd - PSH > Pnl
Modular parameter
Compact parameter
FamilyNr.
ParameterNr.
Parameter description Unit of measur
e
Min Max Factory setting
[for WTM200
(*)]
Prewash module
Pty 4 0 Type of prewash moduleModular Rack Type:- 0/“1165-600” module from 1165 mm or from 600mm- 1/“1490” module from 1490 mm.
- - - 1165-600
Compact Rack Type:- “0” module from 1165 mm, from 600 mm, from 44”or from 22” “0” module from 1165 mm or from 600mm- “1” module from 1490 mm (meaningless for compactRT).“1” module from 1490 mm.
- - - 0
Stanby level
SbL(**) 4 1 Indicates the maximum level in the prewash tank.The filling stops when the water level reaches thisvalue.
mmH2O 60 400 220
Run level PSS(**) 4 2 The value for the maximum level is modified from“Stanby level” to “Run level” during prewashingphase in order to avoid water loss when the pumpsstop.
mmH2O 60 400 180
Drain max lev.
PSd(**) 4 3 Meaninful only during “Drain and clean” cycle.Indicates the maximum level during “Drain and clean”cycle.
mmH2O 60 400 190
Max lev. hister.
PSH(**) 4 4 Indicates the hysteresis level relative to the maximumlevel in the prewash tank. It is related to the “Stanbylevel” , to the “Run level” and to the “Drain max lev.”.
mmH2O 0 80 30
Working level
PnL(**) 4 5 Indicates the water level in the prewash tank enablingthe prewash tank heating elements and the prewashpumps operations.
mmH2O 60 400 90
Tank temper.
Prt 4 7 Tank temperature set point. °C / °F 5/41
90/194
10/50
Sanit. temper.
PSt 4 8 Tank temperature set point during sanitization phase(only on machines with sanitization - N.B.: heatingelement must be installed in prewash module).
°C / °F 10/50
90/194
75/167
Histesys temp.
PtH 4 9 Hysteresis temperature relative to tank temperatureset point.
°C / °F 1/2 50/90 5/9
Prew. san.
durat.
SPd 4 10 Duration of wash tank cleaning phase during asanitization cycle.
sec 0 250 60
Drain delay
dPd 4 12 Time between reaching level “0” (air trap level) in thetank and closing of the drain solenoid valve; allowscomplete emptying of tank.
sec 0 200 30
Autom. drain del.
APd 4 13 Time between two automatic water changes. If thisparameter is set at zero the function is disabled.
min 0 250 50
Water to drain
qPd 4 14 Quantity of water to be drained with each automaticemptying.
mmH2O 0 50 10 (****)
Max temper. prew.
dPt 4 15 Max permissible temperature in prewash tank. If thetank temperature exceeds the set temperature, aquantity of water equal to the quantity set by meansof the "Water to drain" parameter is drained.If this parameter is set at zero the function isdisabled.
°C / °F 0/32
99/210
40/104
Pulse/lit prewash
PLP 4 16 Indicates the impulses per litre characterising thepossible flow meter connected to the prewashmodule feed.The rating plate data of the flow meter used.
P/Lit 0 999 0
Warning lev prew.
Alt 4 17 Indicates the max. level allowed in the wash tankbefore the start of an automatic draining cycle. Toprevent water spilling from the door in case ofclogging of the overflow due to dirt.
mmH2O 180 400 270
O. 5956.573.04 P. 23 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
(*) For the other equipment families, see par. .
A4.1.6 DT MODULE
The DT MODULE family parameters are selected and edited by using the keys in the same way as thatdescribed for the USER SETTINGS family.The DT MODULE family contains the parameters that identify the drying zone (DT) characteristics.
The DT MODULE / dt family parameters are described below:
For setting the Standard/0 or New type/1 parameter refer to the tables listed below.
(****) PREWASH TANKS 600 mm /22” 1165 mm /44” 1490 mm
Tank capacity 45 l 100 l 150 lWater to drain (in litres/mm) 0,136 l/mm 0,32 l/mm 0,485 l/mm
MODULAR RACK TYPE COMPACT RACK TYPE AND USA MODULAR
Modular paramet
er
Compact parameter
FamilyNr.
ParameterNr.
Parameter description Unit of measure
Min Max Factory setting
Dt temper.
dtt 5 0 Drying tunnel temperature set point. °C / °F 10/50
90/194
70/158
Dt hist. temp.
dtH 5 1 Hysteresis temperature relative to the drying tunneltemperature set point.
°C / °F 0/0 50/90
3/5
Dt fan delay
Afd 5 3 Time between stop of DT heating element and stopof DT fan. This parameter ensures a correct coolingfor the DT heating element.
sec 0 250 120
Dt type. d_t 5 4 Indicates the type of DT installed. - Standard
/0
New type/
1
Standard/0
DT MODULE
O. 5956.573.04 P. 24 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
MODULAR RACK TYPE (WTM / RTM)The dryer tunnels for the Modular RT's cannot be installed on the Compact RT's (old range) or the Short Compacts (newrange).
Factory code Factory model appropriate DT/HAB Dt type. (d_t)534100 WTM140ERA
DT 900 mm864500 ADTLER/MD
DT 600 mm864510 ADTER/MD
DT 90°864512 ADTERC90MD
Standard/0
534102 WTM140ERB534104 WTM165ERA534106 WTM165ERB534108 WTM200ERA534110 WTM200ERB534112 WTM250ERA534114 WTM250ERB534116 WTM300ERA534118 WTM300ERB534120 WTM180ERA534122 WTM180ERB534260 RTM140ERA
Standard/0
534262 RTM140ERB534264 RTM165ERA534266 RTM165ERB534268 RTM180ERA534270 RTM180ERB534272 RTM200ERA534274 RTM200ERB534101 WTM140ELA
DT 900 mm864501 ADTLEL/MD
DT 600 mm864511 ADTEL/MD
DT 90°864513 ADTELC90MD
Standard/0
534103 WTM140ELB534105 WTM165ELA534107 WTM165ELB534109 WTM200ELA534111 WTM200ELB534113 WTM250ELA534115 WTM250ELB534117 WTM300ELA534119 WTM300ELB534121 WTM180ELA534123 WTM180ELB534261 RTM140ELA
Standard/0
534263 RTM140ELB534265 RTM165ELA534267 RTM165ELB534269 RTM180ELA534271 RTM180ELB534273 RTM200ELA534275 RTM200ELB534124 WTM140SRA
DT 900 mm864514 ADTLSR/MD
Standard/0
534126 WTM165SRA534128 WTM180SRA534130 WTM200SRA534132 WTM250SRA534134 WTM300SRA534125 WTM140SLA
DT 900 mm864515 ADTLSL/MD
534127 WTM165SLA534129 WTM180SLA534131 WTM200SLA534133 WTM250SLA534135 WTM300SLA
O. 5956.573.04 P. 25 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
A4.1.7 HACCP
The HACCP family parameters are selected and edited by using the keys in the same way as that describedfor the USER SETTINGS family.
SHORT COMPACT RACK TYPE (WTCS/ RTCS)The dryer tunnels for the Short Compacts (new range) cannot be installed on the Modular RT's or the Compact RT's (oldrange).
Factory code Factory model appropriate DT/HAB Dt type. (d_t)
534300 WTCS90ERB
DT 900 mm864516 ADTRTER9
DT 600 mm864518 ADTRTER6
DT 90°864520 ADTRTERC
HAB 600 mm864506 HABRTER
New type/1
534302 WTCS140ERA534304 WTCS140ERB534306 WTCS180ERA534308 WTCS180ERB534310 WTCS250ERA534312 WTCS250ERB534314 RTCS90ERB534316 RTCS140ERA534318 RTCS140ERB534320 RTCS180ERA534322 RTCS180ERB534324 RTCS250ERA534326 RTCS250ERB534340 WTCS140RAO534342 WTCS140RBO534344 WTCS180RAO534346 WTCS180RBO534348 RTCS140RAO534350 RTCS140RBO534352 RTCS180RAO534354 RTCS180RBO534301 WTCS90ELB
DT 900 mm864517 ADTRTEL9
DT 600 mm864519 ADTRTEL6
DT 90°864521 ADTRTELC
HAB 600 mm864507 HABRTEL
New type/1
534303 WTCS140ELA534305 WTCS140ELB534307 WTCS180ELA534309 WTCS180ELB534311 WTCS250ELA534313 WTCS250ELB534315 RTCS90ELB534317 RTCS140ELA534319 RTCS140ELB534321 RTCS180ELA534323 RTCS180ELB534325 RTCS250ELA534327 RTCS250ELB534341 WTCS140LAO534343 WTCS140LBO534345 WTCS180LAO534347 WTCS180LBO534349 RTCS140LAO534351 RTCS140LBO534353 RTCS180LAO534355 RTCS180LBO
O. 5956.573.04 P. 26 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
The HACCP family contains the parameters that identify the HACCP connection characteristics.
The HACCP / HAC family parameters are described below:
A4.1.8 RATING PLATE (ONLY FOR MODULAR RACK TYPE NON USA)
The RATING PLATE family contains the parameters that identify the machine rating data.
The RATING PLATE family parameters are selected and edited by using the keys in the same way as thatdescribed for the USER SETTINGS family except for the "STRING" parameters given in the following table.
After a “STRING” is displayed
the parameter can be edited by pressing the confirm key; the selection arrow moves from the parameter nameto the parameter value.
MODULAR RACK TYPE COMPACT RACK TYPE
Modular paramet
er
Compact parameter
FamilyNr.
ParameterNr.
Parameter description Unit of
measure
Min Max Factory
setting
HACCP address
Adr 6 0 Specific address of equipment in an HACCP network. - 0 254 1
IR Address
IrA 6 1 Specific address of equipment in an IrDa communicationnetwork.
- 0 254 1
HACCP baud rate
Hbr 6 2 Indicates the communication speed of the equipment inan HACCP network.
- 1200/0
19200/4
9600/3
IR baud rate
Ibr 6 3 Indicates the communication speed of the equipment inan IrDa communication network.
- 1200/0
19200/4
9600/3
Enable IR
IrE 6 4 Parameter not used - 0 1 0
HACCP
RATING PLATE
RATING PLATE
P.N.C.
0000000000000
RATING PLATE
P.N.C.
0000000000000
O. 5956.573.04 P. 27 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
Use the increase and decrease keys to move the cursor until it is under the digit to be modified. Press theconfirm key to modify the selected digit.
The digit flashes and the value of the digit selected can be modified by using the increase and decrease keys.Press the confirm key to save the new value. Press the accessory functions key to exit without saving.When all the digits have been modified as required, press the accessory functions key to return to parameter selection mode.The RATING PLATE family parameters are described below:
(*****) The installer must set the day, month and year of installation.
A4.2 DATALOG (ONLY FOR MODULAR RACK TYPE NON USA)
Accessing the "DATALOG" mode allows a number of events that occurred in the machine to be displayed.In addition to the event, the screen also shows the time the event began and ended, as well as other informa-tion whose significance depends on the type of event recorded.Every event is characterised by a START date and time and a STOP date and time.The event STOP can be recorded when its cause is no longer present (e.g. a temperature exceeding the per-missible upper limit and then coming within the correct range),
or when the machine is switched off following shutdown by the user (POWER OFF) or no power (POWERFAIL). In the latter case, event STOP is described with the indication POWER OFF or POWER FAIL.
Parameter name
FamilyNr.
Parameter
Nr.
Parameter description Unit of measu
re
Min Max Factory setting
Example “STRING” parameter
P.N.C. 7 0 Product Number Code - - - - 534104 00 YesSerial
number 7 1 Serial number - - - - 54600001 Yes
Model 7 2 Factory Model - - - - WTM165ERA+DT
Yes
Constr. year 7 3 Year of construction - - - - 2007 YesProd. site 7 4 Production site (6 = Washing) - 0 10 6 6 Yes
Inst. power 7 5 Installed power kW - - - 42,3 KW YesVoltage supply 7 6 Power supply voltage F - - - AC 400 V 3P N Yes
Frequency 7 7 Frequency Hz 50 60 50 50 Hz NoMax.
current 7 8 Absorbed current A 6 32 6 65A No
MCA 7 9 MCA (Minimum supply Circuit Ampacity)[for USA versions only]
A - - - ----- Yes
MOP 7 10 MOP (Maximum Overcurrent Protection) [for USA versions only]
A - - - ----- Yes
Prot. degree 7 11 Protection rating - IPX5 IPX5 YesInst. day 7 12 Installation day (*****) - - - - 20 Yes
Inst. month 7 13 Installation month (*****) - - - - 06 YesInst. year 7 14 Installation year (*****) - - - - 07 Yes
RATING PLATE
P.N.C.
0000000000000
EVENT DATALOG34 WASH OVERTEMP.TYPE DD-MM-YY HH:HH VALUESTART 10-10-05 14:10 80 °CWASH OVERTEMP.STOP 10-10-05 14:15
O. 5956.573.04 P. 28 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
If accessing the display of an event that began after the last machine start and which has not ended becauseits cause is still present, closing of the event is not displayed.
EVENT DATALOG34 WASH OVERTEMP.TYPE DD-MM-YY HH:HH VALUESTART 10-10-05 14:10 80 °CPOWER OFFSTOP 10-10-05 14:15
EVENT DATALOG34 WASH OVERTEMP.TYPE DD-MM-YY HH:HH VALUESTART 10-10-05 14:10 80 °CSTOP ------------ --:-- -------
O. 5956.573.04 P. 29 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
List of events documented by the DATALOG:
Event number
Event name Event description Event value (VALUE)
1 BOIL. TEMP. HIGH The boiler temperature has exceeded the temperature set pointby 7 °C/13 °F.
Indicates the boiler temperature at the timeof event recording.
2 DUO TEMP. HIGH The duo rinse temperature has exceeded the temperature setpoint by 8 °C/14 °F.
Indicates the duo rinse temperature at thetime of event recording.
3 WASH. TEMP. HIGH The wash tank temperature has exceeded the temperature setpoint by 8 °C/14 °F.
Indicates the wash tank temperature at thetime of event recording.
4 PREW. TEMP. HIGH The prewash tank temperature has exceeded the temperatureset point by 35 °C/63 °F.
Indicates the prewash temperature at thetime of event recording.
5 DT TEMP. HIGH The dry tunnel temperature has exceeded the temperature setpoint by 15 °C/27 °F.
Indicates the dry tunnel temperature at thetime of event recording.
6 BOIL. TEMP. LOW During the wash phase the boiler temperature has decreasedby more than 12 °C/25 °F with respect to the permissible min.value (– hysteresis temperature set point).
Indicates the boiler temperature at the timeof event recording.
7 DUO TEMP. LOW During the wash phase the duo rinse temperature has decreasedby more than 15 °C/27 °F with respect to the permissible min.value (–hysteresis temperature set point).
Indicates the duo rinse temperature at thetime of event recording.
8 WASH TEMP. LOW During the wash phase the wash tank temperature hasdecreased by more than 15 °C/27 °F with respect to thepermissible min. value (–hysteresis temperature set point).
Indicates the wash tank temperature at thetime of event recording.
9 DT TEMP. LOW During the wash phase the dry tunnel temperature hasdecreased by more than 15 °C/27 °F with respect to thepermissible min. value (–hysteresis temperature set point).
Indicates the dry tunnel temperature at thetime of event recording.
11 AIRG. FILL. TOUT Alarm number 11 has occurred:The Air Gap was not completely filled within the max. filling time.
Indicates the air gap level at the time ofevent recording.
12 AIRG. LEV. FAULT Alarm number 12 has occurred:The pressure sensor on the rinse module electronic board doesnot work correctly.
Indicates the air gap level at the time ofevent recording.
13 DUO FILL. TOUT Alarm number 13 has occurred:The Duo-rinse tank was not completely filled within the max.filling time.
Indicates the duo rinse level at the time ofevent recording.
14 DUO LEV. FAULT Alarm number 14 has occurred:The pressure sensor on the Duo-rinse tank does not workcorrectly.
Indicates the duo rinse level at the time ofevent recording.
15 BOIL. HEAT. TOUT Alarm number 15 has occurred:The required temperature was not reached in the boiler within themax. heating time.
Indicates the boiler temperature at the timeof event recording.
16 BOILER OVERTEMP. Alarm number 16 has occurred:The water temperature in the boiler is too high
Indicates the boiler temperature at the timeof event recording.
17 BOILER NTC SHORT Alarm number 17 has occurred:The boiler temperature sensor is short circuited.
Not significant
18 BOILER NTC OPEN Alarm number 18 has occurred:The boiler temperature sensor is open.
Not significant
19 DUO HEAT. TOUT Alarm number 19 has occurred:The required temperature was not reached in the Duo-rinse tankwithin the max. heating time.
Indicates the duo rinse temperature at thetime of event recording.
20 DUO OVERTEMP. Alarm number 20 has occurred:The water temperature in the Duo-rinse tank is too high.
Indicates the duo rinse temperature at thetime of event recording.
21 DUO NTC SHORT Alarm number 21 has occurred:The Duo-rinse tank temperature sensor is short circuited.
Not significant
22 DUO NTC OPEN Alarm number 22 has occurred:The Duo-rinse tank temperature sensor is open.
Not significant
23 RIN. PUMP THERM. Alarm number 23 has occurred:SHORT COMPACT AND MODULAR: The rinse pump thermalprotector has tripped.USA COMPACT: the rinse pump, wash pump or CU thermalprotector has tripped.
Not significant
24 DUO PUMP THERM. Alarm number 24 has occurred:The Duo-rinse pump thermal protector has tripped.
Not significant
25 DRAIN DUO TOUT Alarm number 25 has occurred:The Duo-rinse tank was not completely emptied within the max.emptying time.
Indicates the duo rinse level at the time ofevent recording.
27 INVERTER ERROR Alarm number 27 has occurred:The motor control inverter has generated an error.
Indicates the selected speed at the time ofevent recording.
30 DRAIN AIRG TOUT Alarm number 30 has occurred:The Air gap was not completely emptied within the max.emptying time.
Indicates the airgap level at the time of eventrecording.
31 WASH FILL. TOUT Alarm number 31 has occurred:The wash tank was not completely filled within the max. fillingtime.
Indicates the wash tank level at the time ofevent recording.
32 WASH LEV. FAULT Alarm number 32 has occurred:The pressure sensor on the wash tank does not work correctly.
Indicates the wash tank level at the time ofevent recording.
33 WASH HEAT. TOUT Alarm number 33 has occurred:The required temperature in the wash tank was not reachedwithin the max. heating time.
Indicates the wash tank temperature at thetime of event recording.
O. 5956.573.04 P. 30 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
Event number
Event name Event description Event value (VALUE)
34 WASH OVERTEMP. Alarm number 34 has occurred:The water temperature in the wash tank is too high.
Indicates the wash tank temperature at thetime of event recording.
35 WASH NTC SHORT Alarm number 35 has occurred:The wash tank temperature sensor is short circuited.
Not significant
36 WASH NTC OPEN Alarm number 36 has occurred:The wash tank temperature sensor is open.
Not significant
37 WASH PUMP1 THER. Alarm number 37 has occurred:The upper wash pump thermal protector has tripped.(short compact and modular machines only)
Not significant
38 WASH PUMP2 THER. Alarm number 38 has occurred:The lower wash pump thermal protector has tripped.(modular machines only)
Not significant
39 CU FAN THER. Alarm number 39 has occurred:The CU (condensing unit) fan thermal protector has tripped.(short compact and modular machines only)
Not significant
40 DRAIN WASH TOUT Alarm number 40 has occurred:The wash tank was not completely emptied within the max.emptying time.
Indicates the wash tank level at the time ofevent recording.
42 AIRGAP LEV. LOW The air gap tank water level has fallen by more than 10 mm withrespect to the permissible min. level (–hysteresis set point level).
Indicates the air gap level at the time ofevent recording.
43 DUO LEV. LOW The duo rinse tank water level has fallen by more than 10 mmwith respect to the permissible min. level (–hysteresis set pointlevel).
Indicates the duo rinse level at the time ofevent recording.
44 WASH LEV. LOW The wash tank water level has fallen by more than 20 mm withrespect to the permissible min. level (–hysteresis set point level).
Indicates the wash tank level at the time ofevent recording.
45 PREWASH LEV.LOW
The prewash tank water level has fallen by more than 20 mmwith respect to the permissible min. level (–hysteresis set pointlevel).
Indicates the prewash tank level at the timeof event recording.
46 POWER ON Records appliance activation. Not significant47 FORCED WASH A wash start has been forced. Indicates the boiler temperature at the time
of event recording.48 EMERGENCY
SWITCHThe emergency mushroom has been pressed. Not significant
49 PARAMETER MODE Parameter mode has been accessed. Not significant50 PARAMETER
MODIF.A parameter has been modified. Indicates the modified family and parameter
number.51 PREW. FILL. TOUT Alarm number 51 has occurred:
The prewash tank was not completely filled within the max. fillingtime.
Indicates the prewash tank level at the timeof event recording.
52 PREW. LEV. FAULT Alarm number 52 has occurred:The pressure sensor on the prewash tank does not workcorrectly.
Indicates the prewash tank level at the timeof event recording.
53 PREW. HEAT. TOUT Alarm number 53 has occurred:The required temperature in the prewash tank was not reachedwithin the max. heating time.
Indicates the prewash tank temperature atthe time of event recording.
54 PREW. OVERTEMP. Alarm number 54 has occurred:The water temperature in the prewash tank is too high.
Indicates the prewash tank temperature atthe time of event recording.
55 PREW. NTC SHORT Alarm number 55 has occurred:The prewash tank temperature sensor is short circuited.
Not significant
56 PREW. NTC OPEN Alarm number 56 has occurred:The prewash tank temperature sensor is open.
Not significant
57 PREW. PUMP THER. Alarm number 57 has occurred:The prewash pump thermal protector has tripped.
Not significant
58 DRAIN PREW. TOUT Alarm number 58 has occurred:The prewash tank was not completely emptied within the max.emptying time.
Indicates the prewash tank level at the timeof event recording.
O. 5956.573.04 P. 31 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
Event number
Event name Event description Event value (VALUE)
60 CU NTC SHORT The warning number 60 has occurred:The CU temperature sensor is short circuited.
Not significant
61 CU NTC OPEN The warning number 61 has occurred:The CU temperature sensor is open.
Not significant
62 HEAT PUMP FAULT The warning number 62 has occurred:Indicates that the heat pump has generated an error.
Not significant
63 CU TEMP. HIGH The CU temperature has exceeded by 8°C/14°F degrees thepermissible max. value to ensure the correct operation of theheat pump.
Indicates the CU temperature at the time ofevent recording.
64 CU TEMP. LOW During the wash phase the CU temperature has decreased bymore than 10 °C/18 °F with respect to the permissible min. value(–hysteresis temperature set point) to ensure the correctoperation of the heat pump.
Indicates the CU temperature at the time ofevent recording.
65 LEV. LOW WASH Washing has stopped due to a lowering of the levels Indicates the air gap level at the time ofevent recording.
66 RINSE FLOW CTRL A calibration cycle for the rinse flow shutter has been started. Whole part and fractional part of the flowmeasured.
71 DT HEAT. TOUT Alarm number 71 has occurred:The required temperature in the drying tunnel was not reachedwithin the max. heating time.
Indicates the drying tunnel temperature atthe time of event recording.
72 DT OVERTEMP. Alarm number 72 has occurred:The temperature in the drying tunnel is too high.
Indicates the drying tunnel temperature atthe time of event recording.
73 DT NTC SHORT Alarm number 73 has occurred: ( Up to version FW 1.52)The drying tunnel temperature sensor is short circuited.
Not significant
74 DT NTC OPEN Alarm number 74 has occurred:The drying tunnel temperature sensor is open.
Not significant
75 DT FAN THER. Alarm number 75 has occurred:The drying tunnel fan thermal protector has tripped.
Not significant
76 MOT CURR OOR H. Alarm number 76 has occurred:The gear motor supplied current is higher than the maximumvalue allowed for the gear motor current.
Not significant
77 MOT CURR OOR L. Alarm number 77 has occurred:The gear motor supplied current is lower than the minimum valueallowed for the gear motor current.
Not significant
78 HIGH MOT. CURR. Dishes are jammed.:The gear motor supplied current is higher than the value set inthe “Max motor curr.” parameter.
Indicates the supplied current to gear motorat the time of event recording.
79 BOIL. USA T. HI. The first boiler temperature has exceeded the temperature setpoint by 7 °C/13 °F.
Indicates the first boiler temperature at thetime of event recording.
80 BOIL. USA T. LO. During the wash phase the first boiler temperature hasdecreased by more than 12 °C/25 °F with respect to thepermissible min. value (– hysteresis temperature set point).
Indicates the first boiler temperature at thetime of event recording.
81 EN. PEAK CTRL. The “Energy peak control” input has been activated. All theheating elements of the machine remain off during activation ofthis input.
Indicates the boiler temperature at the timeof event recording.
82 BOIL. USA TOUT Alarm number 82 has occurred:The required temperature was not reached in the first boilerwithin the max. heating time.
Indicates the first boiler temperature at thetime of event recording.
83 BOIL. USA OVERT. Alarm number 83 has occurred:The water temperature in the first boiler is too high
Indicates the first boiler temperature at thetime of event recording.
84 BOIL. USA NTC S. Alarm number 84 has occurred:The first boiler temperature sensor is short circuited.
Not significant
85 BOIL. USA NTC O. Alarm number 85 has occurred:The first boiler temperature sensor is open.
Not significant
86 SEN. PRESS. ADJ The pressure sensor setting procedure has been performed. Not significant89 U.I. TEMP. HIGH Alarm number 89 has occurred:
Temperature too high on User interface.Indicates the User interface temperature atthe time of event recording.
90 ECAP ERROR Alarm number 90 has occurred:Communication problems between machine electronic boards.
Indicates the module that generated acommunication error between User interfaceand Mec:1: rinse2: wash4: prewash8: DT.
O. 5956.573.04 P. 32 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
A4.3 INFO
Press the confirm key (“C” - (Figure 1)) when the selection arrow indicates the INFO item and the machinefirmware (FW) versions will be displayed.
Modular Rack Type will show the USER INTERFACE board software version (FW USER e FW LCD) and thePOWER boards software versions (FW RINSE, FW WASH, FW PREWASH, FW DT), Compact Rack Typewill show the USER INTERFACE board software version and the POWER board connected to the USERINTERFACE software version.Press the confirm key to return to the SERVICE MENU.
A4.4 STATISTICS (ONLY FOR MODULAR RACK TYPE NON USA)
Press the confirm key (“C” - (Figure 1)) when the selection arrow indicates the STATISTICS item and thedisplay will show the statistics relevant to starts and activation times of the first electric user of the machine.The table below describes all the codes (LOAD CODE) of the electric users in the machine. The displayshows the minutes of activation and number of starts of the selected electric user starting from the machineinstallation date.It also shows the number of starts (RESET ACT) of the selected electric user, counted from the date indicatedopposite, which corresponds to the last reset.
In fact the number of starts counter for the selected electric user can be reset, by pressing the confirm key; inthis way STATISTICS RESET mode is accessed..
Press the confirm key again to reset the number of starts counter (RESET ACT).The number of starts counter (RESET ACT) is reset and the date and time are saved.If the last reset of the resettable counter (RESET ACT) occurred in the factory, the indication FAC appearsnext to the reset time.Press the accessory functions key to exit STATISTICS RESET mode.
MODULAR RACK TYPE COMPACT RACK TYPE OR USA MODULAR
COMPACT
WASH + RINSE
PREWASH or DT
USA MODULAR
RINSE
WASH
INFOiFW USER 16660200FW LCD 16660300FW RINSE 16360100FW WASH 16360100FW PREWASH 16360100FW DT 16360100
USER
POWER
POWER
1.651.631.63
STATISTICSLOAD CODE 25
12000 MIN 100 ACTRESET ACT DD-MM-YY HH:MM2 10-10-05 14:25
STATISTICS RESETLOAD CODE 25
12000 MIN 100 ACTRESET ACT DD-MM-YY HH:MM2 10-10-05 14:25
O. 5956.573.04 P. 33 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
List of codes (LOAD CODE) of electric users in the machine:
A4.5 RINSE CONTROL ( JUST FOR ATMOSPHERIC RACK TYPE )
Press the confirm key (“C” - (Figure 1)) when the selection arrow indicates the item RINSE CONTROL (nonUSA modular RT's) or when the message rFC appears on the display (USA modular or compact RT's), andthe machine is going to start a rinse flow control cycle.If there is a communication error between the rack type boards, the rinse flow control cycle cannot be carriedout.In this case the display will show:
LOAD CODE Electric user description
1 Air gap filling solenoid valve (atmospheric machines)2 Wash tank filling solenoid valve3 Prewash tank filling solenoid valve4 Boiler heating element5 DUO heating element6 Wash tank heating element7 Wash tank second heating element (for machines with separately controlled tank heating elements only)8 Prewash tank heating element9 DT heating element10 Upper wash pump11 Lower wash pump (only modules with 2 wash pumps)12 Upper prewash pump13 Lower prewash pump (only modules with 2 wash pumps)14 Rinse pump (atmospheric machines) rinse solenoid valve (pressurised machines)15 DUO pump16 CU fan17 DT fan18 DUO tank drain solenoid valve19 Wash tank drain solenoid valve20 Prewash tank drain solenoid valve21 Wash pump impeller drain solenoid valve22 Prewash pump impeller drain solenoid valve23 Gear motor24 Machine infeed motor-driven handling system start command25 Machine outfeed motor-driven handling system start command26 Machine infeed motor-driven handling system speed 2 start command27 Machine infeed motor-driven handling system speed 2 start command28 Heat Pump29 Prewash module door opening30 Wash module door opening31 Rinse module door opening32 DT module door opening33 First boiler heating element (compact USA only)34 Rinse aid dispenser (compact only)
RINSE FLOW CONTROL
PRESS TO EXIT
RINSE FLOW CONTROLNOT AVAILABLE
O. 5956.573.04 P. 34 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
If the communication is working correctly the dispaly informs the user that the machine is ready to start a rinseflow control cycle:
Press the confirm key (“C” - (Figure 1)) and a control cycle is started:
Wait about 2 minutes, during which the machine performs a series of air gap filling solenoid valve and rinsepump activations, until the display will show the actual rinse flow:
Compare the result obtained with the data given in the table below and if the flow is higher or lower than thatindicated in the table, close or open the rinse flow regulating cock and repeat the control cycle until the opti-mum value is reached.
WARNING:
The Rack Type leaves the factory with the cock already adjusted in the optimum position.
WARNING:
The indication of rinse flowrate can be subject to an error of ± 0,3 litres/min.
MACHINE TYPE CORRECT FLOW (Lit/Min)
WTM140 / RTM140 4.00 (5.00 with heat pump)WTM165 / RTM165 5.00WTM180 / RTM180 5.00WTM200 / RTM200 5.00
WTM250 5.00WTM300 5.00
WTCS90 / RTCS90 4.00WTCS140 / RTCS140 4.00WTCS180 / RTCS180 4.00WTCS250 / RTCS250 5.00
WT44 5.00WT66 5.00WT82 5.00WT105 5.00
RINSE FLOW CONTROL
OR TO EXIT
PRESS TO START
RINSE FLOW CONTROL
RINSE FLOW CONTROL
IN PROGRESS
rfCpRG
RINSE FLOW CONTROL
5,0 Lit MinPRESS
TO REPEAT OR TO EXIT
O. 5956.573.04 P. 35 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
A4.6 KEY MANAGEMENT ( JUST FOR MODULAR RACK TYPE )
Not available.
A4.7 SENSOR ADJUSTMENT
Press the “Confirm” button - “C” (Figure 1) - when the selection arrow indicates the item SENS. ADJUST.(Modular RT's no USA) or when the item SAd (Compact RT's or USA Modular) is displayed, to access theprocedure for setting the machine pressure sensors.The pressure sensors are fitted inside the electronic boards and read the levels of the Duo Rinse tank, washtank, prewash tank and Airgap. It is advisable to carry out this procedure when replacing one of the followingboards:1 - Air gap level sensor card (Atmospheric RT's)2 - Prewash module power board (Modular RT's)2 - Wash module power board (Modular RT's)4 - Rinse module power board (Modular RT's)5 - Wash+Rinse module power board (Compact RT's)
WARNING:
All the tanks and the airgap must be completely emptied before carrying out the pressure sensor set-ting procedure.
WARNING:
The Rack Type leaves the factory with the pressure sensors already set to the optimum value.
Pressure sensor setting cannot be carried out if an error in communication between the Rack Type boards isin progress.In this case the display will show:
If the communication is working correctly the dispaly informs the user that the machine is ready for carryingout pressure sensor setting.
PRES. SENS. SET-UP
PRESS TO EXIT
PRES. SENS. SET-UPNOT AVAILABLE
snSAdJn A
PRES. SENS. SET-UP
OR TO EXIT
PRESS TO STARTsnSAdJrdY
O. 5956.573.04 P. 36 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
Press the confirm key - “C” (Figure 1) - and the setting cycle is started:
Wait about 5 seconds, until the display will show:
If the pressure sensor setting procedure is sterted without having previously emptied the tanks and air gap,the following message appears:
A4.8 MOTOR ADJUSTMENT
Press the “confirm” button “C” (Figure 1) when the selection arrow indicates the item “MOTOR ADJUST” (nonUSA Modular RT's) or when the item GAD (USA modular or compact RT's) appears on the display, and thegear motor current setting procedure is accessed.
WARNING:
The procedure is carried out after the installation of possible external tables and without placingracks in the machine.
In fact, the machine has an algorithm that controls the current absorbed by the feed gear motor and blocks therack feed in case of mechanical jamming of racks or dishes. For the control of current to be carried out in thebest of ways, setting of the gear motor current must carried out.Gear motor setting cannot be carried out if an error in communication between the cards of the Rack Type isin progress. In this case the display shows:
PRES. SENS. SET-UP
PRES. SENS. SET-UP
IN PROGRESS
snSAdJPrG
PRES. SENS. SET-UP
PRESS TO EXIT
DONE. snSAdJEnd
PRES. SENS. SET-UP
PRESS TO EXIT
NOT EXECUTEDEMPTY BOTH TANKS AND AIRGAPBEFORE MAKING SENSORS SET-UP
snSAdJn_d
GEARMOTOR SET-UP
PRESS TO EXIT
GEARMOTOR SET-UPNOT AVAILABLE
motAdJn A
O. 5956.573.04 P. 37 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
If the communication functions properly, the display shows the screen indicating that the machine is ready tocarry out gear motor current setting.
Press the confirm button “C” (Figure 1) to start the setting cycle.
WARNING:
If an alarm relevant to the gear motor (27-76-77) is in progress, a door is opened or the emergencystop is activated, gear motor setting is not carried out and the display shows.
If none of the above events occurs, gear motor setting is carried out with the following criteria:the gear motor is made to operate at all the speeds provided for and the absorbed current is measured foreach speed. The measured value is added to the value of the “Mot. curr. margin” (GCM) parameter(“GENERIC FUNC” family) and the value thus obtained is saved and associated with the corresponding speed.A table is thus created where each speed is associated with the corresponding max. current.Example: if at 25 Hz the current measured = 33dec A and the “Mot. curr. margin” (GCM) parameter = 2decA,in normal operation at the speed of 25 Hz, the max. current that can be absorbed by the gear motor is 34decA before shutting down the machine and showing the message:)
The value of theo “Mot. curr. margin” (GCM) parameter makes the machine more or less sensitive to possiblejamming.
WARNING:
Do not modify the “Mot. curr. margin” (GCM) parameter unless expressly requested by the factory.
GEARMOTOR SET-UP
OR TO EXIT
PRESS TO STARTmotAdJrdy
GEARMOTOR SET-UP
NOT EXECUTED
PRESS TO EXIT
motAdJn_d
sEEitEins
O. 5956.573.04 P. 38 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
During the setting procedure, which lasts approx. 3 minutes, the display shows the following screen:
At the end of the current setting procedure the display shows the following screen:
It is advisable to carry out gear motor current setting upon machine installation and when one of the followingcomponents is replaced:1. Gearmotor2. Inverter3. Rinse module (Modular) or Wash+Rinse module (Compact) power board4. User interface board.Setting is not carried out in the factory, since current absorption depends on the machine power supply volt-age. When the machine leaves the factory, the current absorption limit is given by the value of the “Maxmotor curr.” (GCU) .
WARNING:
The parameter “Max motor curr.” (GCU) have following functions:
- if set to 0, the gear motor absorbed current control is disabled (even if it was the routine current setting);
- if the current setting procedure was not carried out, it represents the max. current threshold;
- if modified, it represents the max. current threshold even if the gear motor current setting procedurewas carried out. To obtain the speed/ current correspondence again, it is necessary to launch the cur-rent setting procedure again.When the gearmotor current is calibrated, the parameter GCU is automatically set to the maximumvalue obtained in the calibration table.
B PROGRAMMING SHEETSWhen installing a new user interface card in the equipment it must be configured according to the machine inwhich it is being installed. All the necessary information is given below; carry out the following steps:1. With the machine code, find the Prog. number in the table given below 2. Follow the instructions on the PROG XXX sheets (next pages)3. In case of card replacement, with the machine code find the corresponding LAYOUT number and refer to
the LAYOUTS given in the section “LAYOUT OF CONNECTORS”
WARNING:
The parameters that must be configured are installation day, month and year (see par. A4.1.8 RATINGPLATE (ONLY FOR MODULAR RACK TYPE NON USA)), all the specific configuration parameters ofeach equipment family (see par. B PROGRAMMING SHEETS) and the configuration parameters of the“specific functions” (refer to par. B1 SPECIFIC FUNCTIONS).
GEARMOTOR SET-UP
IN PROGRESS
GEARMOTOR SET-UP
MotAdJprG
GEARMOTOR SET-UP
DONE
PRESS TO EXIT
MotAdJEnD
O. 5956.573.04 P. 39 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
Table 2 Machine codes list and relative programming sheets
Factory Code Factory Model Prog Layout Factory Code Factory Model Prog Layout
534070 WT44BL208 023 11 13 534186 WT105BL208 018 5 8 14 15 16 17534071 WT44BR208 023 11 13 534187 WT105BR208 018 5 8 14 15 16 17534072 WT44BL240 023 11 13 534188 WT105BL240 018 5 8 14 15 16 17534073 WT44BR240 023 11 13 534189 WT105BR240 018 5 8 14 15 16 17534074 WT44CL208 025 11 13 534260 RTM140ERA 001 2 3 (4)534075 WT44CR208 025 11 13 534261 RTM140ELA 001 2 3 (4)534076 WT44CL240 025 11 13 534262 RTM140ERB 001 2 3 (4)534077 WT44CR240 025 11 13 534263 RTM140ELB 001 2 3 (4)534090 WT66BL208 024 10 11 12 13 534264 RTM165ERA 002 2 3 (4)534091 WT66BR208 024 10 11 12 13 534265 RTM165ELA 002 2 3 (4)534092 WT66BL240 024 10 11 12 13 534266 RTM165ERB 002 2 3 (4)534093 WT66BR240 024 10 11 12 13 534267 RTM165ELB 002 2 3 (4)534094 WT66CL208 026 10 11 12 13 534268 RTM180ERA 003 1 2 3 (4)534095 WT66CR208 026 10 11 12 13 534269 RTM180ELA 003 1 2 3 (4)534096 WT66CL240 026 10 11 12 13 534270 RTM180ERB 003 1 2 3 (4)534097 WT66CR240 026 10 11 12 13 534271 RTM180ELB 003 1 2 3 (4)534100 WTM140ERA 001 2 3 (4) 534272 RTM200ERA 004 1 2 3 (4)534101 WTM140ELA 001 2 3 (4) 534273 RTM200ELA 004 1 2 3 (4)534102 WTM140ERB 001 2 3 (4) 534274 RTM200ERB 004 1 2 3 (4)534103 WTM140ELB 001 2 3 (4) 534275 RTM200ELB 004 1 2 3 (4)534104 WTM165ERA 002 2 3 (4) 534300 WTCS90ERB 007 6 9 (7)534105 WTM165ELA 002 2 3 (4) 534301 WTCS90ELB 007 6 9 (7)534106 WTM165ERB 002 2 3 (4) 534302 WTCS140ERA 008 6 9 (7)534107 WTM165ELB 002 2 3 (4) 534303 WTCS140ELA 008 6 9 (7)534108 WTM200ERA 004 1 2 3 (4) 534304 WTCS140ERB 008 6 9 (7)534109 WTM200ELA 004 1 2 3 (4) 534305 WTCS140ELB 008 6 9 (7)534110 WTM200ERB 004 1 2 3 (4) 534306 WTCS180ERA 009 5 6 8 9 (7)534111 WTM200ELB 004 1 2 3 (4) 534307 WTCS180ELA 009 5 6 8 9 (7)534112 WTM250ERA 005 1 2 3 (4) 534308 WTCS180ERB 009 5 6 8 9 (7)534113 WTM250ELA 005 1 2 3 (4) 534309 WTCS180ELB 009 5 6 8 9 (7)534114 WTM250ERB 005 1 2 3 (4) 534310 WTCS250ERA 010 5 6 8 9 (7)534115 WTM250ELB 005 1 2 3 (4) 534311 WTCS250ELA 010 5 6 8 9 (7)534116 WTM300ERA 006 1 2 3 (4) 534312 WTCS250ERB 010 5 6 8 9 (7)534117 WTM300ELA 006 1 2 3 (4) 534313 WTCS250ELB 010 5 6 8 9 (7)534118 WTM300ERB 006 1 2 3 (4) 534314 RTCS90ERB 007 6 9 (7)534119 WTM300ELB 006 1 2 3 (4) 534315 RTCS90ELB 007 6 9 (7)534120 WTM180ERA 003 1 2 3 (4) 534316 RTCS140ERA 008 6 9 (7)534121 WTM180ELA 003 1 2 3 (4) 534317 RTCS140ELA 008 6 9 (7)534122 WTM180ERB 003 1 2 3 (4) 534318 RTCS140ERB 008 6 9 (7)534123 WTM180ELB 003 1 2 3 (4) 534319 RTCS140ELB 008 6 9 (7)534124 WTM140SRA 011 2 3 (4) 534320 RTCS180ERA 009 5 6 8 9 (7)534125 WTM140SLA 011 2 3 (4) 534321 RTCS180ELA 009 5 6 8 9 (7)534126 WTM165SRA 012 2 3 (4) 534322 RTCS180ERB 009 5 6 8 9 (7)534127 WTM165SLA 012 2 3 (4) 534323 RTCS180ELB 009 5 6 8 9 (7)534128 WTM180SRA 013 1 2 3 (4) 534324 RTCS250ERA 010 5 6 8 9 (7)534129 WTM180SLA 013 1 2 3 (4) 534325 RTCS250ELA 010 5 6 8 9 (7)534130 WTM200SRA 014 1 2 3 (4) 534326 RTCS250ERB 010 5 6 8 9 (7)534131 WTM200SLA 014 1 2 3 (4) 534327 RTCS250ELB 010 5 6 8 9 (7)534132 WTM250SRA 015 1 2 3 (4) 534340 WTCS140RAO 027 6 9 (7)534133 WTM250SLA 015 1 2 3 (4) 534341 WTCS140LAO 027 6 9 (7)534134 WTM300SRA 016 1 2 3 (4) 534342 WTCS140RBO 027 6 9 (7)534135 WTM300SLA 016 1 2 3 (4) 534343 WTCS140LBO 027 6 9 (7)534174 WT82AL208 017 14 15 16 17 534344 WTCS180RAO 028 5 6 8 9 (7)534175 WT82AR208 017 14 15 16 17 534345 WTCS180LAO 028 5 6 8 9 (7)534176 WT82AL240 017 14 15 16 17 534346 WTCS180RBO 028 5 6 8 9 (7)534177 WT82AR240 017 14 15 16 17 534347 WTCS180LBO 028 5 6 8 9 (7)534178 WT82BL208 017 14 15 16 17 534348 RTCS140RAO 027 6 9 (7)534179 WT82BR208 017 14 15 16 17 534349 RTCS140LAO 027 6 9 (7)534180 WT82BL240 017 14 15 16 17 534350 RTCS140RBO 027 6 9 (7)534181 WT82BR240 017 14 15 16 17 534351 RTCS140LBO 027 6 9 (7)534182 WT105AL208 018 5 8 14 15 16 17 534352 RTCS180RAO 028 5 6 8 9 (7)534183 WT105AR208 018 5 8 14 15 16 17 534353 RTCS180LAO 028 5 6 8 9 (7)534184 WT105AL240 018 5 8 14 15 16 17 534354 RTCS180RBO 028 5 6 8 9 (7)534185 WT105AR240 018 5 8 14 15 16 17 534355 RTCS180LBO 028 5 6 8 9 (7)
O. 5956.573.04 P. 40 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WTM140/ RTM140 PROG 0011. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Ws Ri / 0 Type of machine: Without DtWs Ri Dt / 3 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 25 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 85 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 45 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 50 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 61 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 40 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU No / 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1165 / 0 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank "warmup end" temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.
Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 41 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WTM165/ RTM165 PROG 0021. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Ws Ri / 0 Type of machine: Without DtWs Ri Dt / 3 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 27 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 110 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 51 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 58 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 61 Enable draining and cleaning cycles.Heat two comm. H2C Yes / 1 Wash tank heating element management.Heating manage b_t Medium / 2 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU No / 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1490 / 1 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank "warmup end" temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.
Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 42 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WTM180/ RTM180 PROG 0031. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Pw Ws Ri / 1 Type of machine: Without DtPw Ws Ri Dt / 2 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 35 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 108 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 58 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 59 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 63 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU No / 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter PREWASH MODULE and set the following parameters.
Wash module ttY 1165 / 0 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter DT MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter WASH MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 43 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WTM200/ RTM200 PROG 0041. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Pw Ws Ri / 1 Type of machine: Without DtPw Ws Ri Dt / 2 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 40 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 105 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 63 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 65 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 63 Enable draining and cleaning cycles.Heat two comm. H2C Yes / 1 Wash tank heating element management.Heating manage b_t Medium / 2 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU No / 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1490 / 0 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 44 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WTM250 PROG 0051. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Pw Ws Ri / 1 Type of machine: Without DtPw Ws Ri Dt / 2 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 53 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 99 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 83 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 65 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 63 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU No / 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1490 / 1 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.Standby level SbL 205 Indicates the max. level in prewash tank.Run level Pss 170 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 45 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WTM300 PROG 0061. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Pw Ws Ri / 1 Type of machine: Without DtPw Ws Ri Dt / 2 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 60 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 100 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 100 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 60 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 63 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software/ 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU No / 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1490 / 1 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1490 / 1 Type of prewash module.Standby level SbL 205 Indicates the max. level in prewash tank.Run level Pss 170 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 46 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WTCS90/RTCS90 PROG 0071. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 4 Type of machine: Without Dt6 Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 27 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 36 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 55 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 27 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 36 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 55 if Rinse autostart r_A = 0)
Drain enable drE 37 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
0 Celsius visualization1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.0 Up to serial number 811000001 From serial number 81100001
Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 40 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t 1 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 47 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WTCS140/RTCS140 PROG 0081. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 4 Type of machine: Without Dt6 Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 27 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 36 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 55 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 45 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 22 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 33 if Rinse autostart r_A = 0)
Drain enable drE 37 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
0 Celsius visualization1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.0 Up to serial number 811000001 From serial number 81100001
Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 40 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t 1 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 48 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WTCS180/RTCS180 PROG 0091. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 8 Type of machine: Without Dt10 Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 35 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 66 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 88 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 58 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 40 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 48 if Rinse autostart r_A = 0)
Drain enable drE 39 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
0 Celsius visualization1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.0 Up to serial number 811000001 From serial number 81100001
Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 40 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t 1 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 49 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WTCS250/RTCS250 PROG 0101. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 8 Type of machine: Without Dt10 Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 57 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 63 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 73 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 80 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 45 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 52 if Rinse autostart r_A = 0)
Drain enable drE 39 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
0 Celsius visualization1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.0 Up to serial number 811000001 From serial number 81100001
Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 0 Type of prewash module.Standby level SbL 205 Indicates the max. level in prewash tank.Run level Pss 170 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t 1 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 50 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WTM140S PROG 0111. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Ws Ri / 0 Type of machine: Without DtWs Ri Dt / 3 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 25 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 85 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 45 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 50 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 61 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 82 Boiler temperature set point at start of rinse stage.Boiler temper. bot 82 Boiler temperature set point.Boiler temper warmup bti 70 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 40 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU Yes / 1 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1165 / 0 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 51 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WTM165S PROG 0121. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Ws Ri / 0 Type of machine: Without DtWs Ri Dt / 3 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 27 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 110 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 51 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 58 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 61 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 82 Boiler temperature set point at start of rinse stage.Boiler temper. bot 82 Boiler temperature set point.Boiler temper warmup bti 70 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU Yes / 1 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1490 / 1 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 52 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WTM180S PROG 0131. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Pw Ws Ri / 1 Type of machine: Without DtPw Ws Ri Dt / 2 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 35 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 108 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 58 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 59 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 63 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 82 Boiler temperature set point at start of rinse stage.Boiler temper. bot 82 Boiler temperature set point.Boiler temper warmup bti 70 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU Yes / 1 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1165 / 0 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 53 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WTM200S PROG 0141. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Pw Ws Ri / 1 Type of machine: Without DtPw Ws Ri Dt / 2 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 40 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 105 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 63 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 65 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 63 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 82 Boiler temperature set point at start of rinse stage.Boiler temper. bot 82 Boiler temperature set point.Boiler temper warmup bti 70 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU Yes / 1 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1490 / 0 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 54 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WTM250S PROG 0151. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Pw Ws Ri / 1 Type of machine: Without DtPw Ws Ri Dt / 2 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 53 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 99 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 83 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 65 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 63 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 82 Boiler temperature set point at start of rinse stage.Boiler temper. bot 82 Boiler temperature set point.Boiler temper warmup bti 70 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU Yes / 1 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1490 / 1 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1165-600 / 0 Type of prewash module.Standby level SbL 205 Indicates the max. level in prewash tank.Run level Pss 170 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 55 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WTM300S PROG 0161. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp Yes / 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt Pw Ws Ri / 1 Type of machine: Without DtPw Ws Ri Dt / 2 Type of machine: With Dt
Appl. direct. Ad Left / 0 Rack feed direction: LeftRight / 1 Rack feed direction: Right
Speed nr. 1 sp1 60 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 100 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 100 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 60 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 63 Enable draining and cleaning cycles.Heat two comm. H2C No / 0 Wash tank heating element management.Heating manage b_t High / 0 Machine heating power management.Boiler load tank btf No / 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
No / 0 Celsius visualizationYes / 1 Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.Software / 0 Up to serial number 71800000
Mechanical / 1 From serial number 71800001Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF No / 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 82 Boiler temperature set point at start of rinse stage.Boiler temper. bot 82 Boiler temperature set point.Boiler temper warmup bti 70 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU Yes / 1 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1490 / 1 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn No / 0 Without CU
Yes / 1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 1490 / 1 Type of prewash module.Standby level SbL 205 Indicates the max. level in prewash tank.Run level Pss 170 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t Standard / 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 56 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WT82 PROG 0171. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 0 Type of machine: Without Dt3 Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 70 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 25 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 100 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 17 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 61 Enable draining and cleaning cycles.Heat two comm. H2C 1 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF
1
Unit of measure used in displaying the temperatures; if set to “Yes” thetemperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius. Celsius visualization. Fahrenheit visualization
Rinse autostart r_A 1 Indicates the type of rinse stage control.Max motor curr. GCU vedi par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 1 Tank temperature setting according to NSF standards.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 198 Boiler temperature set point at start of rinse stage.Boiler temper. bot 187 Boiler temperature set point.Boiler temper warmup bti 187 Boiler warm-up temperature.Delta T stand-by btd 9 Boiler temperature decrease during standby.First boil. temp. Fbt 138 First USA compact boiler temperature set point.Duo temper. dut 172 Tank temperature set point.Hist. duo temp. dtH 4 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1 Type of wash module.Tank temper. tut 172 Tank temperature set point.Histeresys temp. ttH 0 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 172 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 0 Type of prewash module.
Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 158 Drying tunnel temperature set point.DT type d_t 1 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 57 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WT105 PROG 0181. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 1 Type of machine: Without Dt2 Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 70 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 52 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.Speed nr. 2 sp2 100 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 38 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set. Drain enable drE 63 Enable draining and cleaning cycles.Heat two comm. H2C 1 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF
1
Unit of measure used in displaying the temperatures; if set to “Yes” thetemperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius Celsius visualization Fahrenheit visualization
Rinse autostart r_A 1 Indicates the type of rinse stage control.Max motor curr. GCU vedi par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 1 Tank temperature setting according to NSF standards.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 198 Boiler temperature set point at start of rinse stage.Boiler temper. bot 187 Boiler temperature set point.Boiler temper warmup bti 187 Boiler warm-up temperature.Delta T stand-by btd 9 Boiler temperature decrease during standby.First boil. temp. Fbt 138 First USA compact boiler temperature set point.Duo temper. dut 172 Tank temperature set point.Hist. duo temp. dtH 4 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 1 Type of wash module.Tank temper. tut 172 Tank temperature set point.Histeresys temp. ttH 0 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 172 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 158 Drying tunnel temperature set point.DT type d_t 1 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 58 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WT44B PROG 0231. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 12 Type of machine: Without Dt- Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 31 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 44 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 55 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 63 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 22 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 55 if Rinse autostart r_A = 0)
Drain enable drE 53 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF
1
Unit of measure used in displaying the temperatures; if set to “Yes” thetemperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.0 Up to serial number 811000001 From serial number 81100001
Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 1 Tank temperature setting according to NSF standards.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 198 Boiler temperature set point at start of rinse stage.Boiler temper. bot 187 Boiler temperature set point.Boiler temper warmup bti 187 Boiler warm-up temperature.Delta T stand-by btd 126 Boiler temperature decrease during standby.First boil. temp. Fbt 138 First USA compact boiler temperature set point.Duo temper. dut 158 Tank temperature set point.Hist. duo temp. dtH 9 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 172 Tank temperature set point.Histeresys temp. ttH 0 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 172 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PRy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 158 Drying tunnel temperature set point.DT type d_t 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 59 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WT66B PROG 0241. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 14 Type of machine: Without Dt- Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 31 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 85 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 88 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 63 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 42 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 48 if Rinse autostart r_A = 0)
Drain enable drE 55 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
1 Fahrenheit visualizationRinse autostart r_A Indicates the type of rinse stage control.
0 Up to serial number 811000001 From serial number 81100001
Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 1 Tank temperature setting according to NSF standards.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 198 Boiler temperature set point at start of rinse stage.Boiler temper. bot 187 Boiler temperature set point.Boiler temper warmup bti 187 Boiler warm-up temperature.Delta T stand-by btd 126 Boiler temperature decrease during standby.First boil. temp. Fbt 138 First USA compact boiler temperature set point.Duo temper. dut 158 Tank temperature set point.Hist. duo temp. dtH 9 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 172 Tank temperature set point.Histeresys temp. ttH 0 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 172 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PRy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 158 Drying tunnel temperature set point.DT type d_t 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 60 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WT44C PROG 0251. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 12 Type of machine: Without Dt- Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 31 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 44 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 55 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 63 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 22 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 55 if Rinse autostart r_A = 0)
Drain enable drE 53 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF
1
Unit of measure used in displaying the temperatures; if set to “Yes” thetemperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius Fahrenheit visualization
Rinse autostart r_A Indicates the type of rinse stage control.0 Up to serial number 811000001 From serial number 81100001
Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 1 Tank temperature setting according to NSF standards.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 198 Boiler temperature set point at start of rinse stage.Boiler temper. bot 50 Boiler temperature set point.Boiler temper warmup bti 50 Boiler warm-up temperature.Delta T stand-by btd 126 Boiler temperature decrease during standby.First boil. temp. Fbt 32 First USA compact boiler temperature set point.Duo temper. dut 158 Tank temperature set point.Hist. duo temp. dtH 9 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 172 Tank temperature set point.Histeresys temp. ttH 0 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 172 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PRy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 158 Drying tunnel temperature set point.DT type d_t 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 61 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WT66C PROG 0261. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 14 Type of machine: Without Dt- Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 31 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 85 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 88 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 63 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 42 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 48 if Rinse autostart r_A = 0)
Drain enable drE 55 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
1 Fahrenheit visualizationRinse autostart r_A Indicates the type of rinse stage control.
0 Up to serial number 811000001 From serial number 81100001
Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 1 Tank temperature setting according to NSF standards.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 198 Boiler temperature set point at start of rinse stage.Boiler temper. bot 50 Boiler temperature set point.Boiler temper warmup bti 50 Boiler warm-up temperature.Delta T stand-by btd 126 Boiler temperature decrease during standby.First boil. temp. Fbt 32 First USA compact boiler temperature set point.Duo temper. dut 158 Tank temperature set point.Hist. duo temp. dtH 9 Tank hysteresis temperature.Drain del. airgap Add 32 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 172 Tank temperature set point.Histeresys temp. ttH 0 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 172 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PRy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 158 Drying tunnel temperature set point.DT type d_t 0 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 62 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
WTCS140O/RTCS140O PROG 0271. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 5 Type of machine: Without Dt7 Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 27 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 36 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 55 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 45 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 2 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 33 if Rinse autostart r_A = 0)
Drain enable drE 37 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
0 Celsius visualization1 Fahrenheit visualization
Rinse autostart r_A 1 Indicates the type of rinse stage control.Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 40 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t 1 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 63 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
WTCS180O/RTCS180O PROG 0281. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Set default par. sdp 1 Sets all parameters to their default value.2. Switch the machine off and then on again.3. GENERIC FUNC. GFu Enter GENERIC FUNC. and set the following parameters.
Appl. type APt 9 Type of machine: Without Dt11 Type of machine: With Dt
Appl. direct. Ad 0 Rack feed direction: Left1 Rack feed direction: Right
Speed nr. 1 sp1 35 Indicates feed gear motor operation frequency at speed 1 [Hz].Wash time sp 1 rd1 66 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 1 [s] is set.(Set to 88 if Rinse autostart r_A = 0)
Speed nr. 2 sp2 58 Indicates feed gear motor operation frequency at speed 2 [Hz].Wash time sp 2 rd2 40 Time from when the last rack releases the auto start lever until the
wash pumps stop when speed 2 [s] is set.(Set to 48 if Rinse autostart r_A = 0)
Drain enable drE 39 Enable draining and cleaning cycles.Heat two comm. H2C 0 Wash tank heating element management.Heating manage b_t 0 Machine heating power management.Boiler load tank btf 0 The tank is filled by means of a dedicated solenoid valve.Fahrenheit vis. CF Unit of measure used in displaying the temperatures; if set to “Yes” the
temperature is displayed in degrees Fahrenheit, otherwise in degreesCelsius
0 Celsius visualization1 Fahrenheit visualization
Rinse autostart r_A 1 Indicates the type of rinse stage control.Max motor curr. GCU see par. A4.8 Indicates the max. current deliverable to the gear motor by the inverter.Nsf settings nSF 0 Duo and tank temperature standard setting.
4. RINSE MODULE rin Enter RINSE MODULE and set the following parameters.Boil. temp. start btS 92 Boiler temperature set point at start of rinse stage.Boiler temper. bot 86 Boiler temperature set point.Boiler temper warmup bti 86 Boiler warm-up temperature.Delta T stand-by btd 5 Boiler temperature decrease during standby.First boil. temp. Fbt 59 First USA compact boiler temperature set point.Duo temper. dut 70 Tank temperature set point.Hist. duo temp. dtH 5 Tank hysteresis temperature.Drain del. airgap Add 40 Time from reaching level 0 (level in air trap) in the air gap, to stopping of
the rinse pump.Duo heat. unrel. dHU 0 Enables activation of the DUO heating element even if the tank and
boiler heating elements are on.5. WASH MODULE tub Enter WASH MODULE and set the following parameters.
Wash module ttY 2 Type of wash module.Tank temper. tut 66 Tank temperature set point.Histeresys temp. ttH 2 Tank hysteresis temperature.Condensing unit CUn 0 Without CU
1 With CUWash temp. ready ttr 64 Wash tank “warmup end” temperature.
6. PREWASH MODULE PrE Enter PREWASH MODULE and set the following parameters.Prewash module PTy 0 Type of prewash module.Standby level SbL 220 Indicates the max. level in prewash tank.Run level Pss 180 Indicates the max. prewash tank level when the prewash pumps are
working.7. DT MODULE dt Enter DT MODULE and set the following parameters.
DT temper dtt 70 Drying tunnel temperature set point.DT type d_t 1 Indicates the type of DT installed.
8. Switch the machine off and then on again.
O. 5956.573.04 P. 64 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
B1 SPECIFIC FUNCTIONS
B1.1 SETTING UNIT OF MEASURE IN FAHRENHEIT
The machines ( apart from Usa Compact machines) leave the factory with the unit of measure used for dis-playing temperatures in degrees Celsius (Fahrenheit vis. = No only for Modular Rack Type and CF= 0only for Compact Rack Type).To set the unit of measure used for displaying temperatures in degrees Fahrenheit, enter in GENERIC FUNC.and set the Fahrenheit vis. parameter = Yes (only for Modular Rack Type no USA) or enter in GFu and setthe CF parameter to 1 (only for Compact Rack Type or USA Modular).
B1.2 LANGUAGE SETTING
The factory-set language on modular machines no USA is English. Set the required language using the“LANGUAGE” parameter in the “USER SETTINGS” family.
B1.3 “MAX. MOTOR CURR.” PARAMETER ( GCU ) SETTING
1. Wait until the machine, complete with tables, is ready for a wash cycle.2. Start a wash cycle and read the current absorbed by the gear motor ( refer to par. A1 “DISPLAY OF AUXILIARY VALUES”).3. Add 2 to the read value (e.g. if “Motor current” = 34 ---> 34+2=36 decA).4. Set the “Max. motor curr.” parameter with the value thus obtained.
WARNING:
The Rack Type leaves the factory with the “Max motor curr.” parameter already set to the optimumvalue. Reset it only when replacing a PCB or the gear motor.
WARNING:
The “Max motor curr.” ( GCU ) parameter indicates the max. current deliverable to the gear motor bythe inverter only if automatic current setting was not carried out (see paragraph A4.8 MOTOR ADJU-STMENT); if this parameter is modified, the max. current values calculated with the automatic settingprocedure no longer have any effect on operation but the new current limit is represented by the“Max motor curr.” ( GCU ) parameter.
O. 5956.573.04 P. 65 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
C CONNECTORS LAYOUT
C1 POWER BOARDS CONNECTORS LAYOUT
LAYOUT 1 PREWASH ( MODULAR NON USA)
19
18
16
31
RL1_B
RL2_BRL3_BRL4_B
RL5
RL6
RL7
RL8
RL9
RL10
VD
R5V
DR6
VD
R7
VD
R8
VD
R9V
DR
11
VD
R3
VD
R2
VD
R4
VD
R1
C6
4 C6
3
U5
C6
5
C6
7
C6
9
X1
5 X1
6
JP1
C4
C7
7
U1
C3
U1
2
PTC
3
T1
C9
C10
U2
U1
4
U1
3
OPTY1
OPTY2
R122
R129
TY1
TY2
VDR12
VD
R1
0
VD
R1
3 L1
L3
C5
L2
PTC
2
X1
3
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F2
9
F3
0
F3
1
F3
2
F3
3
F3
4
F3
5
F3
6
F3
7
F3
8
F3
9
F4
0X
1X
2X
3X
4X
5X
6X
7X
8X
9X
10
X1
1
JP7
U1
5
O. 5956.573.04 P. 66 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
LAYOUT 2 WASH ( MODULAR NON USA)
19
18
16
31
31
RL1_B
RL2_BRL3_BRL4_B
RL5
RL6
RL7
RL8
RL9
RL10
VD
R5
VD
R6
VD
R7
VD
R8
VD
R9V
DR
11
VD
R3
VD
R2
VD
R4
VD
R1
C6
4 C6
3
U5
C6
5
C6
7
C6
9
X1
5 X1
6
JP1
C4
C7
7
U1
C3
U1
2
PTC
3
T1
C9
C10
U2
U1
4
U1
3
OPTY1
OPTY2
R122
R129
TY1
TY2
VDR12
VD
R1
0
VD
R1
3 L1
L3
C5
L2
PTC
2
X1
3
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F2
9
F3
0
F3
1
F3
2
F3
3
F3
4
F3
5
F3
6
F3
7
F3
8
F3
9
F4
0X
1X
2X
3X
4X
5X
6X
7X
8X
9X
10
X1
1
JP7
U1
5
ONLY WITHOUTPREWASH PREWASH
ONLY WITHOUT
O. 5956.573.04 P. 67 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
LAYOUT 3 RINSE ( MODULAR NON USA)
RL1_B
RL2_BRL3_BRL4_B
RL5
RL6
RL7
RL8
RL9
RL10
VD
R5
VD
R6
VD
R7
VD
R8
VD
R9V
DR
11
VD
R3
VD
R2
VD
R4
VD
R1
C6
4 C6
3
U5
C6
5
C6
7
C6
9
X1
5 X1
6
JP1
C4
C7
7
U1
C3
U1
2
PTC
3
T1
C9
C10
U2
U1
4
U1
3
OPTY1
OPTY2
R122
R129
TY1
TY2
VDR12
VD
R1
0
VD
R1
3 L1
L3
C5
L2
PTC
2
X1
3
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F2
9
F3
0
F3
1
F3
2
F3
3
F3
4
F3
5
F3
6
F3
7
F3
8
F3
9
F4
0X
1X
2X
3X
4X
5X
6X
7X
8X
9X
10
X1
1
JP7
U1
5
13
13
81
91
16
17
16
O. 5956.573.04 P. 68 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
LAYOUT 4 DT ( MODULAR NON USA)
19
18
16
31
RL1_B
RL2_BRL3_BRL4_B
RL5
RL6
RL7
RL8
RL9
RL10
VD
R5V
DR6
VD
R7
VD
R8
VD
R9V
DR
11
VD
R3
VD
R2
VD
R4
VD
R1
C6
4 C6
3
U5
C6
5
C6
7
C6
9
X1
5 X1
6
JP1
C4
C7
7
U1
C3
U1
2
PTC
3
T1
C9
C10
U2
U1
4
U1
3
OPTY1
OPTY2
R122
R129
TY1
TY2
VDR12
VD
R1
0
VD
R1
3 L1
L3
C5
L2
PTC
2
X1
3
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F2
9
F3
0
F3
1
F3
2
F3
3
F3
4
F3
5
F3
6
F3
7
F3
8
F3
9
F4
0X
1X
2X
3X
4X
5X
6X
7X
8X
9X
10
X1
1
JP7
U1
5
O. 5956.573.04 P. 69 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
C2 MULTICONNECTOR BOARDS CONNECTORS LAYOUT
LAYOUT 5 PREWASH ( SHORT COMPACT / USA MODULAR)
65
4 3 2 1
98
7
10 11
12
00
91
F28
F27
F26
F25
F24
F23
F22
F21
F20
F19
F18
F17
F16
F15
F14
F13
F12
F11
F10
F9
F8
F7
F6
F5
F4
F3
F2
F1 X1
1X
10
X9
X8
X7
X6
X5
X4
X3
X2
X1
F4
0
F3
9
F3
8
F3
7
F3
6
F3
5
F3
4
F3
3
F3
2
F3
1
F3
0
F2
9
NO USA
NO USA
NO USA
NO USA
O. 5956.573.04 P. 70 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
LAYOUT 6 WASH + RINSE (SHORT COMPACT)
65
4 3 2 1
98
7
10 11
12
00
91
F28
F27
F26
F25
F24
F23
F22
F21
F20
F19
F18
F17
F16
F15
F14
F13
F12
F11
F10
F9
F8
F7
F6
F5
F4
F3
F2
F1 X1
1X
10
X9
X8
X7
X6
X5
X4
X3
X2
X1
F4
0
F3
9
F3
8
F3
7
F3
6
F3
5
F3
4
F3
3
F3
2
F3
1
F3
0
F2
9
O. 5956.573.04 P. 71 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
LAYOUT 7 DT / HAB ( SHORT COMPACT )
65
4 3 2 1
98
7
10 11
12
00
91
X1
X2
X3
X4
X5
X6
X7
X8
X9
X1
0X
11
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F2
9
F3
0
F3
1
F3
2
F3
3
F3
4
F3
5
F3
6
F3
7
F3
8
F3
9
F4
0
BLACK
BLACK
RED
RED
WHITE
WHITE
O. 5956.573.04 P. 72 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
LAYOUT 8 PREWASH ( SHORT COMPACT USA MODULAR)
1 8J35
16
J32
14
J34
19
J29
31
J27
J266 112
5
J25
J30
1
15J23
21
5 1
91
21
2 1 2 1 6 1
13
21
91
51
14
61
41
81317161
Xin
Xo
ut
O. 5956.573.04 P. 73 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
LAYOUT 9 WASH + RINSE ( SHORT COMPACT )
12
J28
31 J51
J21
91
1 6J43 61 1 8J35
16
J32
14
J34
19
J29
31
J27
J266 112
5
J25
J30
1
12
14
J24
J31
15J23
J36 71
21
5 1
91
21
2 1 2 1 6 1
13
21
91
51
14
61
41
81317161
Xin
Xo
ut
O. 5956.573.04 P. 74 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
LAYOUT 10 PREWASH (USA COMPACT)
65
4 3 2 1
98
7
10 11
12
00
91
F28
F27
F26
F25
F24
F23
F22
F21
F20
F19
F18
F17
F16
F15
F14
F13
F12
F11
F10
F9
F8
F7
F6
F5
F4
F3
F2
F1 X1
1X
10
X9
X8
X7
X6
X5
X4
X3
X2
X1
F4
0
F3
9
F3
8
F3
1
F3
0
F2
9
O. 5956.573.04 P. 75 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
LAYOUT 11 WASH - RINSE 44" (USA COMPACT)
65
4 3 2 1
98
7
10 11
12
00
91
F28
F27
F26
F25
F24
F23
F22
F21
F20
F19
F18
F17
F16
F15
F14
F13
F12
F11
F10
F9
F8
F7
F6
F5
F4
F3
F2
F1 X1
1X
10
X9
X8
X7
X6
X5
X4
X3
X2
X1
F4
0
F3
9
F3
8
F3
7
F3
6
F3
5
F3
4
F3
3
F3
2
F3
1
F3
0
F2
9
O. 5956.573.04 P. 76 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
LAYOUT 12 PREWASH 22" (USA COMPACT)
414
15
15 1 1 16
41
19
41
41
16
21
41
14
81819
13
19
68
18
11
9
41
1
11
1 9J37
J42
8
1
1 8J35
1
6
J32
1
4
J34
1
9
J29
3
1
J27
16
J26
12
1
4
J30
15
J23 J25
O. 5956.573.04 P. 77 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
LAYOUT 13 WASH + RINSE 44" (USA COMPACT)
414
15
15 1 1 16
41
19
41
41
16
21
41
14
81819
13
19
68
18
11
9
41
1
11
14
1
4
1
J22
4
1
9
J40
1 9J37
1
6
J43
6
1
J42
8
1
1
8
J41
1 8J35
1
6
J32
1
4
J34
1
9
J29
3
1
J27
16
J26
12
1
4
HACCP
J30
12
1
4
J24
J31
15
J23
J202
5
J21
1
1 8J36
J27
1
3
J25
1
J28
4
1
MACHINE WITH PREWASH
O. 5956.573.04 P. 78 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
LAYOUT 14 RINSE 23" (USA MODULAR)
65
4 3 2 1
98
7
10 11
12
00
91
F28
F27
F26
F25
F24
F23
F22
F21
F20
F19
F18
F17
F16
F15
F14
F13
F12
F11
F10
F9
F8
F7
F6
F5
F4
F3
F2
F1 X1
1X
10
X9
X8
X7
X5
X4
X3
X2
X1
F4
0
F3
9
F3
8
F3
7
F3
6
F3
5
F3
4
F3
3
F3
2
F3
1
F3
0
F2
9
O. 5956.573.04 P. 79 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
LAYOUT 15 WASH 59" (USA MODULAR)
65
4 3 2 1
98
7
10 11
12
00
91
F28
F27
F26
F25
F24
F23
F22
F21
F20
F19
F18
F17
F16
F15
F14
F13
F12
F11
F10
F4
F3
F2
F1 X1
1X
10
X9
X6
X5
X4
X3
X2
X1
F4
0
F3
9
F3
8
F3
1
F3
0
F2
9
O. 5956.573.04 P. 80 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
LAYOUT 16 RINSE 23" (USA MODULAR)
J21
91
1 6J43 61 1 8J35
16
J32
14
J34
19
J29
31
J27
J266 112
5
J25
J30
1
12
14
J24
J31
15J23
J36 71
21
5 1
91
21
2 1 2 1 6 1
13
21
91
51
14
61
41
81317161
Xin
Xo
ut
O. 5956.573.04 P. 81 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
LAYOUT 17 WASH 59" (USA MODULAR)
1 8J35
16
J32
14
J34
19
J29
31
J27
J266 112
5
J25
J30
1
12
14
J24
J31
15J23
21
5 1
91
21
2 1 2 1 6 1
13
21
91
51
14
61
41
81317161X
inXo
ut
O. 5956.573.04 P. 82 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
C3 CONNECTORS LAYOUT LEGEND
C4 END LIMIT SWITCH, ENERGY PEAK CONTROL AND EMERGENCY SWITCH CONNECTIONS
C4.1 MODULAR (NO USA)
The left and right side panels of the dishwasher have a connector “B” (Figure 10), closed with a plug “A”(Figure 10).Unscrew plug “A” (Figure 10) anticlockwise.
C4.1.1 END LIMIT SWITCH CONNECTION
Connect END LIMIT SWITCH (Outfeed side machine) between points 11 and 12 (Figure 11).
C4.1.2 EMERGENCY SWITCH CONNECTION
Connect EMERGENCY SWITCH OUT (Outfeed side machine) between points 7 and 8 (Figure 11) .Connect EMERGENCY SWITCH IN (Infeed side machine) between points 7 and 8 (Figure 11).
F 3- F12 Main supply connector
F13-F16 Loads connectorF20-F28 Loads connectorF21-F31 Loads connectorF32-F37 Loads connectorF38-F40 Loads connector x1 Temperature sensor connector x2 Temperature sensor connector x4 Temperature sensor connector x5 Thermal protection, autostart, emergency switch - feed back inverter x6 Board identification connector x7 Air gap pressure sensor connector x8 Gearmotor speed signal connector x9 Thermal protection, autostart, emergency switch
x10 Door switch connector - user interface
Figure 10 Electrical connection Figure 11 Detail of electrical connection
A B B
EMERGENCY SWITCH (7-8)
END LIMIT SWITCH (11-12)
O. 5956.573.04 P. 83 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
C4.1.3 ENERGY PEAK CONTROL CONNECTION
Access to the electrical box of rinse module and connect ENERGY PEAK CONTROL between terminals 3and 4 of terminal block X1.
Figura 12 ENERGY PEAK CONTROL CONNECTION
C4.2 USA MODULAR AND COMPACT SHORT
Figura 13 USA MODULAR AND COMPACT SHORT CONNECTIONS
1 2 3 4 5 6 7 8 9 10 1112
ENERGY PEAK CONTROL
X1 (3-4)
ENERGY PEAK CONTROL
X4 (3-4)
EMERGENCY SWITCHXIN (7-8)
EMERGENCYSWITCH
XOUT (11-12)
END LIMIT SWITCH
XOUT (1-2)
O. 5956.573.04 P. 84 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
C4.3 USA COMPACT
C4.3.1 END LIMIT SWITCH CONNECTION
Remove side panel “A” (Figure 14), locate the connector XC_OUT and remove the jumper between terminals11 and 12. Connect END LIMIT SWITCH between terminals 11 and 12 of XC_OUT. Refit panel “A” (Figure 14).
C4.3.2 EMERGENCY SWITCH CONNECTION
Remove side panel “A” (Figure 14), locate the connector XC_OUT and remove the jumper between terminals7 and 8. Connect EMERGENCY SWITCH OUT between terminals 7 and 8 of XC_OUT. Refit panel “A” (Figure 14).Remove side panel “B” (Figure 14), locate the connector XC_IN and remove the jumper between terminals 7and 8. Connect EMERGENCY SWITCH IN between terminals 7 and 8 of XC_IN.Refit panel “B” (Figure 14).
Figura 14 END LIMIT SWITCH AND EMERGENCY SWITCH CONNECTION
C4.3.3 ENERGY PEAK CONTROL CONNECTION
Figure 15 ENERGY PEAK CONTROL CONNECTION
12
11 7
8END LIMIT
SWITCHXC_OUT (11-12)
EMERGENCY SWITCH
XC_OUT (7-8)
XC_OUT
7
8
EMERGENCY SWITCH
XC_IN(7-8)
XC_IN
A
B
414
15
15 1 1 16
41
19
4
21
41
19
6
1
ENERGY PEAK CONTROL
X2 (7-8)
O. 5956.573.04 P. 85 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
D INVERTER PARAMETERS
WARNING:
When replacing the inverter remove the protection label “A” on the top of the same, as indicatedbelow (the protection rating becomes IP20).
D1 INVERTER PROGRAMMING
D1.1 DISPLAY FUNCTIONS
A
Altivar 11
Telemecanique
ENTESC
3 “7 segment” displays.
Exits a menu or parameter or aborts the displayed valueto return to the previous value in the memory.
Returns to the previous menu or parameter, or increases the displayed value.
Enters a menu or a parameter,or saves the displayed parameter or value.
Goes to the next menu orparameter, or decreases thedisplayed value.
Pressing or does
not store the selection
Save the selection:
The display flashes when a value isstored.
ENT
O. 5956.573.04 P. 86 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
D1.2 INVERTER CONTROL TERMINAL ELECTRICAL CONNECTIONS
Figure 16 COMPACT RT Inverter electrical connection
Figure 17 MODULAR RT Inverter electrical connection
D1.3 INVERTER PARAMETER LISTS
Telemecanique speed drive Altivar 11 type ATV11PU12M2E380Parameters for 110Vac gearmotor ( Delta connection)
KEY
COMPACTSHORT(1) White(2) Orange(4) Violet(5) Red(7) Black(8) Yellow(12) Blue
COMPACTUSA(1) - 1 -(2) - 2 -(4) - 4 -(5) - 5 -(7) - 7 -(8) - 8 -(12) - 12 -
KEY
(1) Black(From Ser. Nr. 020)(2) Orange(From Ser. Nr. 020)(4) Grey(5) White(7) Blue(8) Green / Pink(12) Brown / Yellow
Parameter Description Standard machineACC Acceleration ramp time 3.0dEC Deceleration ramp time 0.5LSP Low speed 0.0HSP High speed 100ItH Motor thermal current 3.6
SP2 2nd preset speed 10SP3 3rd preset speed 25SP4 4th preset speed 50Alt Act Scale of analog input 10UdrC UnS Nominal motor voltage 110
RC
RA
0V
AV
1
DO
LI1
+1
5V
(1) (2) (4) (5) (7) (8) (12)R
C
RA
0V
AV
1
DO
LI1
+1
5V
(1) (2) (4) (5) (7) (8) (12)
O. 5956.573.04 P. 87 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
Telemecanique speed drive Altivar 11 type ATV11PU12M2E380 o ATV11PU09M2E380Parameters for 230Vac gearmotor ( Delta connection)
Parameter Description Standard machineFrS Nominal motor frequency 50StA Frequency loop stability 20FLG Frequency loop gain 50UFr Ir compensation 50nCr Nominal motor current 3.6CLI Current limit 3.9nSL Nominal motor slip 5SLP Slip compensation 100COS Nominal motor cosine 0.65
FUn tCC ACt Type of control 2CtCt Type of two wire control Lel
rrS Reverse nOPs2 LIA Preset speed lia nO
LIB Preset speed lib nOHSP LIA Config. input Lia nO
LIB Config. input Lib nOtLS 0.0PI PIF nO
LOC Overload threshold 90tOL Time delay for overl. func. 0API Histeresis freq. reached 0.3LUL Underload threshold 60tUL Time delay for underl. func. 10rSF Fault reset nOrP2 LI Second ramp nOLC2 LI 2nd limit current nOnST Freewheel stop nOStP Controlled stop on loss of line FSTbrA Deceleration ramp adaptation YESAdC ACt Automatic dc injection YES
tdC Injection time on stopping 0.5SdC Injection current 2.9
SfT ACt Frequency range LFSfr Switching frequency 4
FLr Catch on the fly nOdO ACt Analogic output do OCrAtr Automatic restart nObFr Motor frequency 50
SCS Configuration backup nOFCS Reminder of the configuration nO
Parameter Description Standard machineACC Acceleration ramp time 3.0dEC Deceleration ramp time 0.5LSP Low speed 0.0
HSP High speed 100 Modular no USA115 Modular USA
ItH Motor thermal current 1.7SP2 2nd preset speed 10SP3 3rd preset speed 25SP4 4th preset speed 50
O. 5956.573.04 P. 88 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
Parameter Description Standard machineAlt Act Scale of analog input 10UdrC UnS Nominal motor voltage 230
FrS Nominal motor frequency 50StA Frequency loop stability 20FLG Frequency loop gain 50UFr Ir compensation 50nCr Nominal motor current 1.7CLI Current limit 3.1nSL Nominal motor slip 2SLP Slip compensation 100COS Nominal motor cosine 0.65
FUn tCC ACt Type of control 2CtCt Type of two wire control LEL
rrS Reverse nOPs2 LIA Preset speed lia nO
LIB Preset speed lib nOHSP LIA Config. input Lia nO
LIB Config. input Lib nOtLS 0.0PI PIF nO
LOC Overload threshold 90tOL Time delay for overl. func. 0API Histeresis freq. reached 0.3LUL Underload threshold 60tUL Time delay for underl. func. 0rSF Fault reset nOrP2 LI Second ramp nOLC2 LI 2nd limit current nOnST Freewheel stop nOStP Controlled stop on loss of line sup- FSTbrA Deceleration ramp adaptation YESAdC ACt Automatic dc injection YES
tdC Injection time on stopping 0.5SdC Injection current 1.4
SfT ACt Frequency range LfSfr Switching frequency 4
FLr Catch on the fly nOdO ACt Analogic output do FtAAtr Automatic restart nObFr Motor frequency 50SCS Configuration backup nOFCS Reminder of the configuration nO
O. 5956.573.04 P. 89 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
E WARNING MESSAGES AND TROUBLESHOOTINGList of possible documented machine alarms:
CODE DESCRIPTION POSSIBLE CAUSE
11 The Air Gap was not completelyfilled within the max. filling time.
- The air gap water supply cock is not open.- The water filling solenoid valve doesn’t work properly.- The water feed flow is too low.- The water inlet filter is not clean.- The boiler pressure sensor doesn’t work properly.
12 The pressure sensor on the air gapdoes not work correctly.
- The pressure sensor on the air gap doesn’t work properly.- The pressure sensor connector on the air gap is not correctly inserted.- The X7 connector on the rinse board is not correctly inserted.
13 The Duo-Rinse tank was notcompletely filled within the max.filling time.
- The impeller rotation is wrong.- There is a leak in the plumbing circuit that connects the air gap to the rinse jets.- There is a leak in the CU.- The non return valve on the air gap doesn’t work properly.- The DUO tank overflow is not inserted.- The Duo drain solenoid valve doesn’t work properly and remains open.- The pressure sensor on the rinse board doesn’t work properly.- The rinse board doesn’t work properly.
14 The pressure sensor on the Duo-Rinse tank does not work correctly.
- The pressure sensor on the rinse board doesn’t work properly.- The rinse board doesn’t work properly.
15 * The required temperature was notreached in the boiler within the max.heating time.
- The rinse water flow is too high.- A heating element or a heating element branch doesn’t work properly.- The CU is not clean.- The boiler temperature sensor doesn’t work properly.- The boiler heating element starter controller doesn’t work properly or its coil is not correctly connected to the rinse board.
16 The water temperature in the boileris too high.
- The “Boil. temp. start” parameter (bt5) or the “Boiler temper.” parameter (bot) has been changed.- The relay that activates the boiler heating elements starter controller is stuck.
17 The boiler temperature sensor isshort-circuited.
- The boiler temperature sensor is short-circuited.
18 The boiler temperature sensor isopen.
- The boiler temperature sensor is open or disconnected.- The boiler temperature sensor connector is not correctly inserted.- The connector on the rinse board is not correctly inserted.
19 ** The required temperature was notreached in the Duo-Rinse tank withinthe max. heating time.
- The Duo rinse heating element doesn’t work properly.- The Duo rinse temperature sensor doesn’t work properly.- The Duo rinse heating element starter controller doesn’t work properly or its coil is not correctly connected to the rinse board.
20 The water temperature in the Duo-Rinse tank is too high.
- The “Duo temper.” parameter (dut) has been changed.- The relay that activates the Duo rinse heating element starter controller is stuck.
21 The Duo-Rinse tank temperaturesensor is short-circuited.
- The Duo rinse temperature sensor is short-circuited.
22 ** The Duo-Rinse tank temperaturesensor is open.
- The Duo rinse temperature sensor is open or disconnected.- The Duo rinse temperature sensor connector is not correctly inserted.- The connector on the rinse board is not correctly inserted.
23 SHORT compact and modular:Therinse pump thermal protector hastripped.
USA compact: the thermal protectorof one of the following users hastripped:- wash pump- rinse pump- CU fan.
- The rinse pump thermal protector is not correctly set.- The rinse pump doesn’t work properly.- The rinse pump impeller is blocked.
- The wash pump thermal protector is not correctly set.- The wash pump does not work properly.- The wash pump impeller is blocked.- The "Wash module" parameter (ttY) is not correctly set.- The CU fan thermal protector is not correctly set.- The CU fan does not work properly.- The rinse pump thermal protector is not correctly set.- The rinse pump does not work properly.- The rinse pump impeller is blocked.
24 ** The Duo-Rinse pump thermalprotector has tripped.
- The Duo rinse pump thermal protector is not correctly set.- The Duo rinse pump doesn’t work properly.- The Duo pump impeller is blocked.
25 ** The Duo-Rinse tank was notcompletely emptied within the max.emptying time.
- The drain is blocked.- The drain solenoid valve doesn’t work properly.- The Duo rinse tank air trap is not clean.
O. 5956.573.04 P. 90 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
27 The gear motor inverter hasgenerated an allarm.(compactmachines only).
- The inverter or the gear motordoesn’t work properly. Possiblemachine alarms documented on
Possible cause Remedy
1) OCF overcurrent - ramp too short- inertia or load too high- mechanical locking
- check the state of the mechanism.
2) SCF motor short circuit - insulation fault or short- circuit at the drive output
- check the cablesconnecting the drive tothe motor , and the motorinsulation.
3) InF internal fault - internal fault - check the environment(electromagneticcompatibility).- send the drive to bechecked/repaired.
4) CFF configuration fault - The current configuration is inconsistent- some parameters in the inverter have been modified
- return to factory settings.
5) SOF overspeed - instability or- driving load too high- some parameters in the inverter have been modified
- return to factory settings.
6) CrF internal fault - load relay control fault or damaged load resistor
- replace the drive.
7) OHF drive overload - drive temperature too high - check the motor loadand the enviroment.Waitfor the drive to cool downbefore restarting.
8) OLF motor overload - triggered by motor current too high
- check the motor load.Wait for the drive to cooldown before restarting.
9) OSF overvoltage - line voltage too high- disturbed line supply
- check the line voltage.The overvoltage thresoldis 415 V on the DC bus.
10) ObF overvoltage duringdeceleration
- braking too sudden or driving load.
- increase the deceleration time.
11) PHF line phase failure - drive incorrectly supplied ora fuse blown- failure of one phase- unbalanced load
- check the power connection and the fuses.- reset.
12) USF undervoltage - line supply too low- transient voltage dip- damaged load resistor
- check the voltage and the voltage parameter. The undervoltage threshold is 230 V on the DC bus.- replace the drive.
30 ** The Air gap was not completelyemptied within the max. emptyingtime.
- The impeller rotation is wrong.- The non return valve on the air gap doesn’t work properly.- The pressure sensor on the air gap doesn’t work properly.- The air gap air trap is not clean.
31 The wash tank was not completelyfilled within the max. filling time.
- The wash tank water supply cock is not open.- The water load solenoid valve doesn’t work properly.- The water feed flow is too low.- The water inlet filter is not clean.- The pressure sensor on the wash tank doesn’t work properly.- The wash tank overflow has not been inserted.- The wash tank drain solenoid valve doesn’t work properly and remains open.- The pressure sensor on the wash board doesn’t work properly.- The wash board doesn’t work properly.
32 The pressure sensor on the washtank does not work correctly.
- The pressure sensor on the wash board doesn’t work properly.- The wash board doesn’t work properly.
33 ** The required temperature in thewash tank was not reached withinthe max. heating time.
- A heating element or a heating element branch of the wash board doesn’t work properly.- The wash tank temperature sensor doesn’t work properly.- The wash tank heating element starter controller doesn’t work properly or its coil is not correctly connected to the rinse board.
O. 5956.573.04 P. 91 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
34 The water temperature in the washtank is too high.
- The “Tank temper.” parameter (tut) or the “Sanit. temper.” parameter (tSt) has been changed.- The relay that activates the wash tank heating elements starter controller is stuck.
35 The wash tank temperature sensoris short-circuited.
- The wash tank temperature sensor is short-circuited.
36 ** The wash tank temperature sensoris open.
- The wash tank temperature sensor is open or disconnected.- The wash tank temperature sensor connector is not correctly inserted.- The connector on the wash board is not correctly inserted.
37 *** The upper wash pump thermalprotector has tripped (SHORTcompact and modular machines only).
- The upper wash pump thermal protector is not correctly set.- The upper wash pump doesn’t work properly.- The upper wash pump impeller is blocked.
38 ** The lower wash pump thermalprotector has tripped.( modular machines only )
- The lower wash pump thermal protector is not correctly set.- The lower wash pump doesn’t work properly.- The lower wash pump impeller is blocked.- The “Wash module” parameter (ttY) is not correctly set.
39 ** The CU (Condensing unit) fanthermal protector has tripped.(SHORT compact and modularmachines only).
- The CU (Condensing Unit) fan thermal protector is not correctly set.- The CU fan doesn’t work properly.
40 ** The wash tank was not completelyemptied within the max. emptyingtime.
- The drain is blocked.- The drain solenoid valve doesn’t work properly.- The wash tank air trap is not clean.
51 The prewash tank was notcompletely filled within the max.filling time.
- The prewash tank water supply cock is not open.- The water load solenoid valve doesn’t work properly.- The water feed flow is too low.- The water inlet filter is not clean.- The load solenoid valve filter is not clean.- The prewash tank pressure sensor doesn’t work properly.- The prewash tank overflow has not been inserted.- The prewash tank drain solenoid valve doesn’t work properly and remains open.- The pressure sensor on the prewash board doesn’t work properly.- The prewash board doesn’t work properly.
52 The pressure sensor on the prewashtank does not work correctly.
- The pressure sensor on the prewash board doesn’t work properly.- The prewash board doesn’t work properly.
53 ** The required temperature in theprewash tank was not reached withinthe max. heating time.
- A heating element or a heating element branch of the prewash board doesn’t work properly.- The prewash tank temperature sensor doesn’t work properly.- The prewash tank heating element starter controller doesn’t work properly or its coil is not correctly connected to the rinse board.
54 The water temperature in theprewash tank is too high.
- The “Tank temper.” parameter (Prt) or the “Sanit. temper.” parameter (PSt) has been changed.- The relay that activates the wash tank heating elements remote control switch is stuck.
55 The prewash tank temperaturesensor is short-circuited.
- The prewash tank temperature sensor is short-circuited.
56 ** The prewash tank temperaturesensor is open.
- The prewash tank temperature sensor is open or disconnected.- The prewash tank temperature sensor connector is not correctly inserted.- The connector on the prewash board is not correctly inserted.
57 ** The prewash pump thermalprotector has tripped.
- The prewash pump thermal protector is not correctly set.- The prewash pump doesn’t work properly.- The prewash pump impeller is blocked.
58 ** The prewash tank was notcompletely emptied within the max.emptying time.
- The drain is blocked.- The drain solenoid valve doesn’t work properly.- The prewash tank air trap is not clean.
60 The CU temperature sensor is short-circuited (machines with heat pumponly).
- The CU temperature sensor or the connection wires are short-circuited.
61 The CU temperature sensor is open(machines with heat pump only).
- The CU temperature sensor or the connection wires are open.- The CU temperature sensor connector is not properly inserted.- The connector on the wash card is not properly inserted.
62 The heat pump has generated anerror (machines with heat pumponly).
Check the heat pump.
71 ** The required temperature in thedrying tunnel was not reached withinthe max. heating time.
- The DT heating element or the DT heating element branch doesn’t work properly.- The DT temperature sensor doesn’t work properly.- The DT heating element starter controller doesn’t work properly or its coil is not correctly connected to the rinse board.
72 The drying tunnel temperature is toohigh.
- The “Dt temper.” parameter (dtt) has been changed.- The relay that activates the DT heating element starter controller is stuck.- The DT fan doesn’t work properly.- The DT temperature sensor doesn’t work properly.
73 The drying tunnel temperaturesensor is short-circuited.
- The DT temperature sensor is short-circuited.
O. 5956.573.04 P. 92 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
* If the value of the parameter "Heat tim. enable" (HtE) is "Yes" (1), the machine stops when this alarmappears. If the parameter value is "No" (0), the machine does not shut down when this alarm appears.** The machine does not shut down if these alarms appear. Every 8 seconds a message indicating thealarm number, the alarm is shown on the display. A red LED blinks, but the machine continues to carry out thenormal operations.*** This alarm causes machine stop in versions without prewash and with just one wash pump. In WTM140versions the machine stops when this alarm appears. In all the other models the machine continues to work.**** With Dt/ Hab standard models the machine shuts down when this alarm appears, but does not in thenew Dt/ Hab versions.
74 **** The drying tunnel temperaturesensor is open.
- The DT temperature sensor is open or disconnected.- The DT temperature sensor connector is not correctly inserted.- The connector on the DT board is not correctly inserted.
75 ** The drying tunnel fan thermalprotector has tripped.
- The DT fan thermal protector is not correctly set.- The DT fan doesn’t work properly.
76 The gear motor supplied current ishigher than the maximum valueallowed for the “Max motor curr.”.
- The wire connected from the inverter ( Do terminal block) to the elctronic board (X7-5) is short-circuited with the ground.- The inverter parameters are not correctly set.
77 The gear motor supplied current islower than the minimum valueallowed for the gear motor current.
- The wire connected from the inverter ( Do terminal block) to the electronic board (X7-5) is open.- The inverter parameters are not correctly set.- The gear motor is configured with star connection and it must be configured with deltaconnections.
82 ** The required temperature was notreached in the first boiler within themax. heating time.
- The rinse water flow is too high.- A heating element or a heating element branch doesn’t work properly.- The CU is not clean.- The first boiler temperature sensor doesn’t work properly.- The first boiler heating element starter controller doesn’t work properly or its coil is not correctly connected to the rinse board.
83 The water temperature in the firstboiler is too high.
- The “Boil. temp. start” parameter (bt5) or the “Boiler temper.” parameter (bot) has been changed.- The relay that activates the first boiler heating elements starter controller is stuck.
84 The first boiler temperature sensor isshort-circuited.
- The first boiler temperature sensor is short-circuited.
85 The first boiler temperature sensor isopen.
- The first boiler temperature sensor is open or disconnected.- The first boiler temperature sensor connector is not correctly inserted.- The connector on the rinse board is not correctly inserted.
89 The temperature on the userinterface is too high.
- Presence of steam too hot on the user interface board.- The user interface doesn’t work properly.
90( modular machines non USA)
CoM
Err( compact machines or USA
modular)
Communication problems betweenmachine electronic boards.
- The bus connection cables are not correctly connected to all the boards.- One or more boards don’t work properly.- The “Appl. type” parameter (APt) is not correctly set.- The connector X6 is not correctly connected.When alarm 90 appears, the display will show the name (modular rack type no USA) or thenumber (compact rack type or USA Modular), of the electronic board that generated thecommunication error.1: rinse (on USA modular versions only)2: wash (USA modular versions) or wash + rinse (compact)3: prewash4: dt
If, after a communication error, the machine is able to re-enable the communication between theboards, the following message appears on the display:
91 User interface board (modular racktype non USA) out of order.
USA compact machines: Power cardconnected to the user interface cardnot working.
- The user interface board doesn’t work properly (modular rack type).
The Power card connected to the user interface card does not work.The user interface card does not work.The connection between the user card and Power card is damaged.
Modular Compact
PRESS NoCoMErr
I
O. 5956.573.04 P. 93 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
F MODULE COMPOSITION FOR RACK TYPEMODULAR RACK TYPE / USA RINSE WASH PREWASH
600 1165 1490 600 1165 1490
WTM140 / RTM140 X X - - - -WTM165 / RTM165 / WT82 X - X - - -WTM180 / RTM180 X X - X - -WTM200 / RTM200 / WT105 X - X X - -WTM250 X - X - X -WTM300 X - X - - X
SHORT COMPACT RACK TYPE / USA
WASH + RINSE PREWASH
44’’ 22’’ 44’
RTCS90/WTCS90 X - -RTCS140/WTCS140 X - -RTCS180/WTCS180 X X -RTCS250/WTCS250 X - XWT44 X - -WT66 X X -
O. 5956.573.04 P. 94 / 100
DOC. N
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
G FLOWCHARTS FOR TROUBLESHOOTING
(*) If CoM Err1 appears among the communication alarms, correctly set parameter "Apt".
Correctly insert it or replace if neces-sar
Correctly insert them or replace if the contact is open.
Check the values of parameter "Apt" as indi-cated in par. A.4.1.2. Generic.Func.
Make sure connector X6 and relevant jumpers (see Layout 5/ 6/ 7 - page 68, 69 and 70) are properly insert-ed in the respective MEC's.
NO
NO
NO
YES
YES
CoM Err 2 or CoM Err 3 or CoM Err 2 - 4 or CoM Err 2 - 3 - 4 or CoM Err 3 - 4 alarm (*)
START
Replace User A1.
Check the correct power supply 230V (-15% ; +10%) on board AP1 between connector X1 (contact 3) and connector X3 (contact 1).
NO
YES
Check the wiring between connector X3 ofAP1 and connector X21 of AP1 (also checkthe respective through-wall fitting XC2) andrepair/replace the damaged component ifnecessary.
Check the correct power supply230V (-15% ; +10%) on Usercard A1 on connector J21 (con-tacts 1 and 4).
NO
YES
Replace the User AP1.Check the correct power supply230V (-15%; +10%) on boardAP1 in connector J26 (contacts1 and 2).
NO
YES
YES
Continued on the next page.
Check the continuity of the bus communication cable and that it is properly inserted between the User card and the various
MEC's (see communication ca-ble and bus cable path).
Make sure the parameter "Apt" is correctly set according to the type of machine.
COMPACT SHORT
O. 5956.573.04 P. 95 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC.
Check the integrity and continuity of the wir-ing between connector J26 (on board AP1)and connector F1/F4 (on board A2), and re-place it or repair if necessary.
Check the correct power supply230V (-15%; +10%) on MECboard A2 in connectors F1/F4(see Layout 6 - page 69 - con-tacts 1 and 2).
NO
YES
Sostituire la scheda MEC A2.YES
NO
NO
YES
Replace MEC board A2.
Replace board AP1.
Verificare la corretta alimnetazi-one 230V (-15%; +10) sullascheda AP4 (zona prelavaggio44”) o sulla scheda AP5 (zonaprelavaggio 22”) nel connettoreJ25 tra i contatti 1 e 2.
NO
YES
NO
YES
Replace boards AP4/AP5.
NO Check the wiring, the through-wall fittings(XC_4 - Wash+Rinse zone, (XC_35 - Pre-wash zone 44" and (XC_44 - Prewash zone22") and the connectors, and repair/replace ifnecessary.
NO
YES
Return to the wash zone.
NO
YES
Replace boards AP1.
Continued on next page.
YES
Check the correct power supply 230V (-15%; +10%) on board
AP1 in connector J25 (contacts 1 and 2).
Check the correct power supply230V (-15%; +10%) on board MECA6 (prewash zone) in connectorF1/F4 (see Layout 5 - page 68 -contacts 1 and 2).
Check the correct power supply230V (-15%; +10%) on boardAP4 (prewash zone 44") or onboard AP5 (prewash zone 22")in connector J25 (contacts 1 and2).
Check the correct power supply 230V (-15%; +10%) on board
AP4/AP5 in connector J26 (con-tacts 1 and 2).
Check the integrity and continuity of the wir-ing between connector J26 (on board AP4/AP5) and connector F1/F4 (on board A6),and replace/repair if necessary.
Check the correct power supply 230V (-15%; +10%) on board
AP1 in connector J24 (contacts 1 and 2).
If the alarm is only CoM Err2 and there is no error CoM
Err3 or CoM Err4 in progress.
YES
Is the Prewash mod-ule installed?
Is the DT module in-stalled?
NO
YES
NO
NO. 5956.573.04 P. 96 / 100
DOC
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
W+R PWW+RDTW+RDT
BUS CABLE
YES
NO
YES
Check the wiring, the through-wall fittings(XC_3 - Wash+Rinse zone) and the connec-tors between board AP1 in connector J25and MEC board A7 in connector F1/F4, andrepair/replace if necessary.
NO
Replace MEC board A7 (DT/HAB zone).
YES
NO
Replace MEC board A2 (Wash + Rinsezone).
Replace MEC board A4/A5 (Prewash zone).
END
Check the correct power supply230V (-15%; +10%) on boardMEC A7 (DT/HAB zone) in con-nector F1/F4 (see Layout 7 -page 70 - contacts 1 and 2).
Check if on disconnecting the buscable from MEC board A7 (DT/HAB zone) the CoM Err4 alarm orCoM Err 2/4 alarm change to CoMErr4 or CoM Err 3-4 alarm chang-es to CoM Err 4.
Disconnect the bus cables con-nected to the Wash+Rinse card (1 or 2 depending on the type of ma-chine). Does CoM Err 2-3-4 alarm become CoM Err 2-4 or CoM Err 2-3 alarm become CoM Err 2?
NO
NOReconnect the bus cable to MEC board A7 (DT/HAB zone).
Is the Prewash installed?
NO
YES
COMMUNICATION CABLE PATH
. NO. 5956.573.04 P. 97 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC.
Replace the inverter.
NO
NO
Alarm 27: the drive gearmotor inverter hasgenerated an alarm.
START
Check if the parameters are correct.
Correctly enter them according to that indicated in par. D page
82
Check if inverter display is on.
YES NO
YES
Check the correct power supply 230V (-15%; +10%) between terminals 1 and 2 of the inverter.
YES Check continuity between points RC or RA of the invert-er with the machine switched on.
Check the wiring or replace the inverter.
NO
YES
YES
Display the alarms table 27 see par. E page 85.Check the correct power
supply 230V (-15%; +10%) on board AP1 on connector J21 (contacts 7 and 8).
Check the wiring and con-nector.
NO
YES
Check the correct power supply 230V (-15%; +10%) on board AP1 on connector J23 (contacts 3 and 4).
NOCheck the correct power
supply 230V (-15% ; +10%) on the discon-
necting switch box if be-tween connectors F1, F2,
F3 and F4.
Check the wiring and connectors.YES
NO
Mains power trouble.
YES
Check the correct power supply 230V (-15%; +10%) on board AP1 on connector J21 (contacts 5 and 8).
NOReplace board AP1.
YES
Check the correct power supply 230V (-15%; +10%) on board AP1 on connector J21 (contacts 6 and 8).
NO Replace transformer GS1 or check the wiring or connectors.
YES
Check the correct power supply 230V (-15% ; +10%) on board AP1 on connector J21 (contacts 7 and 8).
NOReplace board AP1.
Check the wiring between the in-verter and board AP1 and re-
place the inverter if necessary. END
SHORT COMPACT
NO. 5956.573.04 P. 98 / 100
DOC
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
SHORT COMPACT RTCS90/ WTCS90 AND RTCS140/ WTCS140 WITHOUT DT/HAB
NO
Alarm EMR: error message on display.
START
Check the connection of the emergency buttons on auxiliary board AP1 (located inside the
electrical box in the wash zone). See figure Layout 9 - page 72 - terminal x_IN (contacts 7 and 8)
and X_OUT (contacts 11 and 12).
YES
Interruption in emergency circuit.
Correctly connect and make sure the insulation is not pinched.
NOMake sure the emer-gency buttons have not
been activated.
YES NO
Check continuity on the board AP1 between con-
tacts 7-8 of Terminal Block X-IN and contacts 11-12 of
Terminal Block X-OUT.
YES
Deactivate the emergency buttons.
Check the emergency circuit power supply voltage.
NO
Make sure the wiring be-tween board AP1 and each of the emergency
buttons is not interrupted.
YES
Replace/repair the wiring. Replace the faulty buttons.
NO
Check the correct 24V output power supply from trans-
former GS1 (connector J49 contact 1 and connector J50
contact 2).
Check the correct 230V input power supply to the trans-
former GS1 (connector J44, contacts 1-3), checking on the transformer terminal
board.
YES
Replace the transformer.Check the continuity between connector J49 (contact 1 on
GS1) and connector J32 (con-tact 6 on AP1) and between con-nector J50 (contact 2 on GS1) to
J32 (contact 2 on AP1).
YES
NO Check the wiring and connectors and repair/replace if necessary.
Check continuity between con-nector J32 (contact 3 on AP1) to terminal X_OUT (contact 9
on AP1).
YES
NO Replace board AP1.
Check the continuity be-tween connector J32 (con-
tact 2 on AP1) and connector J27 (contact 3 on
AP1).
YES
NO Replace board AP1.
YES
. NO. 5956.573.04 P. 99 / 100
ElectroluxEFS - Dishwashing Systems PlatformElectrolux Professional
DOC. N
Check the continuity be-tween connector J32 (con-
tact 3 on AP1) and connector J27 (contact 1 on
AP1).
YES
NO Check the jumper on board AP1 (terminal X_OUT between contacts 9 and 10 or 10 and 11). If correct, replace board AP1.
YES
Check the continuity between connector J27 (contact 1 on AP1) and connector F20/F23
(contact 4 on A2) and be-tween connector J27 (contact 3 on AP1) and contactor F20/
F23 (contact 2 on A2).
NO Check the wiring and connectors and re-pair/replace if necessary.
YES
Replace MEC board A2.
END
O. 5956.573.04 P. 100 / 100
Top Related