Rev. 8/2006
Part Number 150224-00
Service & Parts Manual
RTP1300 Blowerwith Internal Drive
Brushless DC Motor& Mounting Bracket Assembly
Contents
Chapter 1: Getting StartedProduct Description 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .About This Manual 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2: Recommended MaintenanceIntroduction 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3: TroubleshootingIntroduction 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Locked Impeller 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Not Operating 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Obstruction 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Over Temperature Shutdown 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Under Voltage Shutdown 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 4: Maintenance and Repair ProceduresIntroduction 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disassembling the Blower 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Reassembling the Blower 4-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Connecting the Lead-Wire Pins 4-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Attaching the Mounting Bracket Assembly 4-5. . . . . . . . . . . . . . . . . . .
AppendixesAppendix A: Replacement Parts List for theRTP1300 Blower with Mounting Bracket Assembly A-1. . . . . . . . . . .Appendix B: Specifications Outline Drawing for theRTP1300 Blower with Mounting Bracket Assembly B-1. . . . . . . . . . . .
TablesTable 3.1. Blower Hookup with 27.6 VDC Motor 3-2. . . . . . . . . . . . . .
FiguresFigure 3.1. Performance Curves for RTP1300 Blowerwith Mounting Bracket Assembly 150224-00(27.6 VDC Motor) 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Figure 4.1. Assembly Drawing for RTP1300 Blowerwith Mounting Bracket Assembly 150224-00(27.6 VDC Motor) 4-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Figure 4.2. Connector Pin-Out Detail 4-5. . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1: Getting Started
1-2 Chapter 1: Introduction
Brushless DC impeller-style blowers offer multispeed aerodynamic perform-ances for all types of high-airflow applications. AMETEK standard designscome with fully integrated electronics and are available in various input volt-ages.
The RTP1300 Blower with Mounting Bracket Assembly has an operating volt-age of 27.6 VDC and a CFM of 237. It has two main components: a blowerand a 27.6 VDC motor.
This manual provides step-by-step instructions and annotated diagrams forservicing the RTP1300 Blower with Mounting Bracket Assembly. A parts listfor the blower is provided in appendix A.
On the parts lists, each part is identified by part number, item number, quan-tity and description. The item numbers are used to annotate the schematicdiagrams included in this manual (see, for example, figure 4.1 (p. 4-3).Circled numbers on the diagrams refer to the item numbers in the applicableparts list. For example:
8
3
refers to item number 8 (lock nut) and part number 0-7466 on the blowerreplacement parts list (see appendix A).
refers to item number 3 (motor gasket) and part number 5-4003-3 on the blowerreplacement parts list (see appendix A).
These circled numbers also correspond to numbers in the maintenance proce-dures chapter (see chapter 4) of this manual. In the text of the steps, the itemnumbers are enclosed in flat brackets and follow the part name being refer-enced. For example:
motor [6] refers to item number 6 on the blower replacement parts list (see appendix A).
When a notation such as (2x) appears with a part name on an annotated dia-gram, the number refers to the quantity of that particular part that is neededwhere indicated.
PRODUCT DESCRIPTION
ABOUT THIS MANUAL
Chapter 1: Introduction 1-3
The remaining sections of this manual are as follows:
• Chapter 2: Recommended Maintenance
• Chapter 3: Troubleshooting
• Chapter 4: Maintenance and Repair Procedures
• Appendix A: Replacement Parts List for the RTP1300 Blower with Mount-ing Bracket Assembly
• Appendix B: Specifications Outline Drawing for the RTP1300 Blower withMounting Bracket Assembly
Four sets of procedures are included in Chapter 4:
• Disassembling the Blower
• Reassembling the Blower
• Connecting the Lead-Wire Pins
• Attaching the Mounting Bracket Assembly
Chapter 2: Recommended Maintenance
2-2 Chapter 2: Recommended Maintenance
The primary advantage to using brushless DC impeller-style blowers is thelife-cycle cost savings with regard to maintenance. Should the motor fail, itmust be replaced as a unit. It cannot be disassembled and nonworking partsreplaced. All other parts that comprise the RTP1300 Blower with MountingBracket Assembly can be removed and replaced as needed.
INTRODUCTION
Chapter 3: Troubleshooting
3-2 Chapter 3: Troubleshooting
When using the RTP1300 Blower with Mounting Bracket Assembly, you mayencounter one or more of the following problems:
• Locked impeller
• Over temperature shutdown (internal temperature greater than 110_ C)
• Under voltage shutdown (less than 11.0 VDC)
The sections below tell you how to troubleshoot, find the cause of the prob-lem you are experiencing and fix the problem.
If the impeller is not rotating and appears to be locked, refer to the followingsections to determine whether the motor has failed or an obstruction hasimpeded movement of the impeller.
If the motor is not operating, follow the steps below to determine the cause:
1. Incorrect Voltage Connections. Check the connections to the motorterminals to verify that the motor leads are connected to the proper sup-ply voltage according to the hookup settings shown in table 3.1 (p. 3-2).
Table 3.1. Blower Hookupwith 27.6 VDC Motor
Operation Red (+) Yellow Orange
High Speed + 27.6 VDC Open Open
Med Speed + 27.6 VDC + 27.6 VDC Open
Med/Low Speed + 27.6 VDC Open + 27.6 VDC
Low Speed + 27.6 VDC + 27.6 VDC + 27.6 VDC
If the leads are reversed, the unit will not operate. A reversed connectionwill short the power source. Check the polarity of the connection to thebus wiring.
The series-protection device allows power to be supplied by the closureof a “fast-acting” contactor, relay or similar device to ensure that theblower will start. AMETEK recommends the use of a series fuse or afast-acting circuit breaker large enough to protect the wiring andelectronics of the device needing circuit/fuse protection.
NOTE
INTRODUCTION
LOCKED IMPELLER
Motor Not Operating
Chapter 3: Troubleshooting 3-3
Correct the voltage-connection error. Normal blower operation shouldbegin when the connection error has been corrected and the protectiondevice reset.
2. Improper Voltage. Check the motor connections with a voltmeter toverify that the proper voltage is being supplied to the motor.
3. Faulty Motor. If the motor is receiving the proper voltage and still doesnot operate, the problem likely is with the motor. Replace the motor, andtry the blower again.
If an obstruction is impeding the rotation of the impeller, disassemble theblower (see chapter 4), and attempt to clear the obstruction. After the obstruc-tion has been cleared, try the blower again.
The blower may be malfunctioning because it has overheated. This meansthat the blower’s internal temperature is greater than 110_ C, the temperatureat which the blower’s internal thermostat is set. Normal operating tempera-ture ranges from -40_ C to 70_ C (see figure 3.1, p. 3-4). Normal operationshould resume when the blower’s internal temperature drops to within therange for normal functioning.
The blower may be malfunctioning because the voltage supplied is less than11.0 VDC, which is the absolute minimum voltage required for normal opera-tion. Optimal voltage is 27.6 VDC. Intermittent voltage should be in the rangeof 18 VDC to 32 VDC.
Check the motor connections with a voltmeter to verify that the proper volt-age is being supplied to the motor. Adjust the voltage as needed, and try theblower again. If the motor is receiving the proper voltage and still does notoperate, the problem likely is with the motor. Replace the motor, and try theblower again.
Obstruction
OVER TEMPERATURE SHUTDOWN
UNDER VOLTAGE SHUTDOWN
3-4 Chapter 3: Troubleshooting
Figure 3.1 Performance Curves for RTP1300 Blower with Mounting Bracket Assembly 150224-00 (27.6 VDCMotor).
Chapter 4: Maintenanceand Repair Procedures
4-2 Chapter 4: Maintenance and Repair Procedures
This chapter provides step-by-step instructions for disassembling and re-assembling the RTP1300 Blower with Mounting Bracket Assembly. Disas-semble the unit as much as needed to replace the failed part. Note, however,that the motor cannot be disassembled and repaired. If the motor fails, a newone is required.
To disassemble the RTP1300 Blower with Mounting Bracket Assembly, followthe steps below, and refer to figure 4.1 (p. 4-3) for an outline drawing of theblower:
1. Disconnect the blower connector from the bus voltage supply.
2. Remove the blower-mounting hardware connecting the blower to themounting surface.
3. Move the blower to a clean work surface.
4. Loosen and remove the 10 Phillips head screws [5] from the top portionof the blower housing [1].
5. Remove the top portion of the blower housing [1].
6. Remove the green impeller clamp [4] from the outer end of the two im-pellers [2] that protrude from the shaft ends of the motor [6].
7. Remove the two impellers [2].
8. Remove the motor [6] from the motor-cradle area of the bottom half of theblower housing [1].
INTRODUCTION
DISASSEMBLING THE BLOWER
Chapter 4: Maintenance and Repair Procedures 4-3
Figure 4.1. Assembly drawing for RTP1300 Blower WMB
Figu
re4.
1.A
ssem
bly
Dra
win
gfo
rRTP
1300
Blo
wer
with
Mou
ntin
gB
rack
etA
ssem
bly
1502
24-0
0(2
7.6
VDC
Mot
or).
ASSEMBLEBLOWERPERDETAILSBELOW
NOTES:UNLESSOTHERWISESPECIFIED.
1.
EACH
IMPELLER.(CLAMPIN
STALLATIO
NPLIERSROTON
TOOLNO.2
05867)
INSTALLIM
PELLERCLAMPS(ITEM
4)ON
IMPELLERHUBS(ITEM
2)PRIO
RTO
INSTALLIN
GIM
PELLERSON
MOTOR.(2)CLAMPSTO
BEIN
STALLEDON
2.
IMPRIN
TEDON
CENTERWALLOFEACH
IMPELLER.E
NSUREIM
PELLERSAREORIENTED
PRESSIM
PELLERSONTO
SHAFTTO
DIM
ENSIO
NSSHOWN.E
NDSOFSHAFTMUSTBEFIXTURED
DURIN
GPRESSIN
GPROCESSTO
PREVENTDAMAGETO
BEARIN
GS.C
HECKROTATIO
NARROW
FORCCW
ROTATIO
NWHEN
VIEWIN
GFROM
LEADWIR
EENDOFMOTOR.
3.
MOTORGASKET(ITEM
3)BETWEEN
MOTORANDMOTOR-C
RADLEAREAIN
TOPBLOWERHOUSIN
G.
PLACESUBASSEMBLEDMOTOR/IMPELLERSIN
TO
BOTTOM
BLOWERHOUSIN
GHALF(ITEM
1)
WITH
(1)MOTORGASKET(ITEM
3)BETWEEN
MOTORANDMOTOR-C
RADLEAREA.P
LACESECOND
ENSUREMOTOR/IMPELLERSAREORIENTEDFORCCW
ROTATIO
NWHEN
VIEWIN
GFROM
LEADWIR
EENDOFMOTOR.
4.
CRADLEAREASID
EWALLASSHOWN.
MOTORASSEMBLYTO
BEPLACEDIN
MOTORCRADLEAREAWITH
LEADWIR
EGROMMETAT
APPROXIM
ATELY45DEGREESASSHOWN.N
OTETHATGROMMETTO
BEPOSITIO
NEDAGAIN
STTHE
5.TESTUNIT
PERPERFORMANCESPECIFIC
ATIO
N15-150224-00.
7MOUNTIN
GBRACKETASSEMBLY
1BLOWERHOUSIN
G
(SEENOTE2)
4IM
PELLERCLAMP,
GREEN
(2X)
2IM
PELLER(2X)[S
EENOTE1]
(SEENOTE4)
9
THREADCUTTIN
G
6MOTORVIEW
B
VIEW
A
VIEW
C
MOTORGASKETSPOSITIO
NEDWITHIN
MOTORCRADLE.O
NEIN
TOPBLOWER
HOUSIN
G(N
EARSID
E);ONEIN
BOTTOM
BLOWERHOUSIN
G(FARSID
E)
10
OUTLETPLENUM
11
GASKET
7MOUNTIN
GBRACKETASSEMBLY
8
LOCKNUT(8X)
10
OUTLETPLENUM
2X
.10
GROMMETPOSITIO
NED
AGAIN
STSID
EWALLOF
MOTOR-C
RADLEAREA
5
PHILLIPSHEAD
SCREW
(10X)
CCW
ROTATIO
N(S
EENOTE2)
3MOTORGASKETIN
BOTTOM
BLOWER
HOUSIN
G(S
EENOTE3)
3
MOTORGASKETIN
TOPBLOWER
HOUSIN
G(S
EENOTE3)
1
BLOWER
HOUSIN
G(TOP)
1
BLOWER
HOUSIN
G(B
OTTOM)
(SEENOTE4)
APPLY1/8”BEADOFSEALANT
(P-1-1968-H
)TO
INSID
ECORNER
OFMOUNTIN
GBRACKETPRIO
RTO
ASSEMBLIN
GPLENUM
(ITEM
10)
SCREW
(4X)
18
CORRUGATEDLOOM
4-4 Chapter 4: Maintenance and Repair Procedures
To reassemble the RTP1300 Blower with Mounting Bracket Assembly, followthe steps below, and refer to figure 4.1 (p. 4-3) for an outline drawing of theblower:
1. Use pliers to place one of the two green impeller clamps [4] onto each ofthe impeller hubs.
Put the impeller clamps [4] on the impeller hubs before installing theimpellers on the motor.STOP
2. Press each impeller [2] flush with the end of the motor shaft.
The ends of each motor shaft must be fixtured during the pressingprocess to prevent damage to the bearings.STOP
3. Check the rotation arrow imprinted on the center wall of each impeller[2]. The impellers [2] should be oriented for counterclockwise rotationwhen viewed from the lead-wire end of the motor [6].
4. Place the partially assembled motor/impellers [6]/[2] into the bottomhalf of the blower housing [1] with one of the two motor gaskets [3] be-tween the motor [6] and the motor-cradle area (see View A in figure 4.1,p. 4-3).
Ensure that motor/impeller [6]/[2] is oriented for counterclockwiserotation when viewed from the lead-wire end of the motor [6].STOP
5. Place the other motor gasket [3] between the motor [6] and the motor-cradle area in the top portion of the blower housing [1] (see View A in fig-ure 4.1, p. 4-3).
6. With the motor/impellers [6]/[2] resting in the motor-cradle area, orientthe lead-wire grommet at approximately a 45° angle as shown View B offigure 4.1 (p. 4-3).
When the motor/impellers [6]/[2] are in place, the grommet will bepositioned against the side wall of the motor-cradle area (see View B infigure 4.1, p. 4-3)
NOTE
7. Place the top portion of the blower housing [1] against the bottom portionof the blower housing [1], lining up the screw holes on the top and bot-tom halves.
8. Insert the 10 Phillips head screws [5] that secure the top and bottom por-tions of the blower housing [1], and torque each to 22 to 24 inch-pounds.
REASSEMBLING THE BLOWER
Chapter 4: Maintenance and Repair Procedures 4-5
To connect the lead-wire pins for the RTP1300 Blower with Mounting BracketAssembly, follow the steps below, and refer to figure 4.2 (p. 4-5):
1. Cut the four leads (two 16-gauge wires and two 14-gauge wires) to thesame length, using the shorter lead to determine the length.
2. Attach the yellow 16-gauge lead to one of the two tan cable seals [16].
Figure 4.2. Connector Pin-Out Detail.
17
CONNECTORMALE
16
TAN (2X)CABLE SEAL,
15 CABLE SEAL, LIGHT GRAY (2X)
PIN TERMINAL (4X)
14
4XPERPENDICULAR TOMOTOR BODY
16 GA (2X)
14 GA (2X)
.24 STRIP (4X)
12.00 ± .25 MEASURED
3. Attach the orange 16-gauge lead to the other tan cable seal [16].
4. Attach the red 14-gauge lead to one of the two light gray cable seals [15].
5. Attach the black 14-gauge lead to the other light gray cable seal [15].
6. Attach a pin terminal [14] to each of the four cable seals [16] and [15].
7. Attach the four pin terminals [14] to the male connector [17].
To attach the mounting bracket assembly [7] to the RTP1600 Blower, followthe steps below, and refer to Views B and C in figure 4.1 (p. 4-3).
1. Install four thread cutting screws [9] as shown in View B of figure 4.1 (p.4-3).
2. Place the rectangular gasket [11] on the flat (top) surface of the mountingbracket assembly [7] (see View C of figure 4.1 (p. 4-3).
3. Line up the eight holes on the blower mounting assembly [7] with theeight holes on the bottom of the blower housing [1].
4. Place a lock nut [8] through each of the eight sets of holes.
5. Torque each lock nut [8] to 22 to 24 inch-pounds.
CONNECTING THE LEAD-WIRE PINS
ATTACHING THE MOUNTING BRACKET ASSEMBLY
Appendix A:Replacement Parts Listfor the RTP1300 Blower
with Mounting Bracket Assembly
A-2 Appendix A: Replacement Parts List for the RTP1300 Blower with Mounting Bracket Assembly
Table A.1: Replacement Parts List for the RTP1300 Blowerwith Mounting Bracket Assembly
AMETEK Part # Item # Quantity Description
150324-00 6 1 Motor, 27.6 VDC (without con-nector)
5-4003-1 1 1 Blower Housing (Top and Bot-tom Portions)
5-4003-2 2 2 Impeller
5-4003-3 3 2 Motor Gasket
5-4003-4 4 2 Impeller Clamp (Green)
5-4003-5 5 10 Phillips Head Screw (#6)
5-44323 7 1 Mounting Bracket Assembly
0-7466 8 8 Lock Nut (#10)
5-7965 9 4 Thread Cutting Screw (#8)
5-4065 10 1 Outlet Plenum
5-4452 11 1 Gasket
40-5144-9 14 4 Pin Terminal
40-5144-5 15 2 Cable Seal (Light Gray)
40-5144-3 16 2 Cable Seal (Tan)
40-5144-26 17 1 Male Connector
121928000 18 1 Corrugated Loom (10 incheslong)
Appendix B:Specifications Outline Drawing
for the RTP1300 Blower withMounting Bracket Assembly
B-2 Appendix B: Specifications Outline Drawing for the RTP1300 Blower with Mounting Bracket Assembly
Figu
reB
.1.
Spec
ifica
tions
Out
line
Dra
win
gfo
rRTP
1300
Blo
wer
with
Mou
ntin
gB
rack
etA
ssem
bly
1502
24-0
0(2
7.6
VDC
Mot
or).
Top Related