KALDEWEI
SPECIFICATIONSRecommended use Domestic, Hotel and Commercial
Material 3.5mm Enamel Steel
Colour availability White (other colour options available)
Weight 50 kg
Overflow MULTIFILLER Integrated Bath Filler & Overflow
Plug and waste 40mm Pop-up Waste and overflow included
Capacity 137L
Fixing Hob Mounted, Built In, Undermounted, or Flush mounted. Sound-deadening pads are a standard inclusion.
Installation Option Leg System #2006759 available for easy installation
CLEANING RECOMMENDATIONS
To see the complete KALDEWEI range go to www.reece.com.au/bathrooms
PURO INSET BATH WITH END MULTIFILLER
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.
PURO
05.06.2008 Gohr, Maße nachgetragen, 16.01.2008 D.VossPR-315-00a
EDV-Nr.GrößeÄußere LängeÄußere BreiteTiefe
Höhe mit FüßenRandhöheAbstand Oberkante bis Mitte Überlau�ochAbstand Wannenrand (Fuß) bis Mitte Ablau�ochDurchmesser Überlau�ochDurchmesser Ablau�ochAbstand Fußseite Wannenrand bis Mitte FußAbstand zwischen den Füßen
a
cd
efghijklmno
Innere Länge (oben)Innere Länge (unten)Innere Breite (oben)Innere Breite (unten)
Fußbreite max. pRandbreite (Fußseite, Kopfseite, Längsseite)* s ; s ;
M 1:20 Badewanne Modell-Nr.:
b
Abstand Mitte Ab- bis Mitte Überlau�och u
Gewicht der Rohwanne (ohne Zubehör) in kgGewicht der emaillierten Wanne in kg
Wasserinhalt bis Überlauf in ltr.
AntislipVollantislip
s1 2 3
2562.00011700x750170075042015101280620460*554-568
6532
310525244575047090,100,60*
652
214
46,2207
50,0
2563.00011800x800180080042016101380670510*553-563
6532
310525246082052090,100,60*
653
214
49,2235
53,6348x348 396x396924x348 1020x396
2583.00011600x700160070042014101180580410x-x
6532
3105252xxx90,100,60
683
214
xx
x
x
2587.00011700x700170070042015101280580410x-x
6532
3105252x
x90,100,60
687
214
xx
xx xx x
2591.00011700x800170080042015101280680460x-x
6532
3105252xxx90,100,85
691
214
xx
xxx
750 470
75090
1700
1510
1280
32
65
554-568
420
310
620
460
100
214
52
52
445
60
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 1
Dimensions are nominal measurements only
page 1 of 4
INSTALLATION INSTRUCTIONS
KALDEWEIPURO INSET BATH WITH END MULTIFILLER
AUSTRALIAN BATH & SHOWER FLOOR INSTALLATION
Australian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be fitted during the final installation and that the bath be covered until all the building work has been completed.
This bath has been supplied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
This clip on material should be cut to the required lengths, mitred at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD OR MASONRY
WALL
PVC TILE TRIM
TILES
SUPPORT BATTEN
page 2 of 4
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
MULTIFILLER INSTALLATION INSTRUCTIONS
KALDEWEIPURO INSET BATH WITH END MULTIFILLER
1. 2.
3. 4.
5.
NOTE: The Back Flow/Non Return Valve included must be installed with this Multifiller
1/2” (15mm) BSP
NOTE: Test spout installation
Remove test spout before final assembly of the finish set (step 4)
6. 40mm BSP
Part Codes Description
23-21315000-00Z KLUDI concealed overflow set
23-7182605-BA KLUDI Multifiller finish set
AS/NZS 3718WMKA 00313
page 3 of 4
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
LEG SYSTEM INSTALLATION INSTRUCTIONS
KALDEWEIPURO INSET BATH WITH END MULTIFILLER
3. Push a suitable length of the tensioning belt onto the retaining bolt (a), engage the threaded hook (c) and tighten by hand using the nut on the base.
1.
Place the bath with its packaging upside down.
2.
Slot the arm straps of the bath cradle (b) onto the lugs (a) on the base of the bath.
b a
c
a
4.
Turn over bath, align with the help of a spirit level by turning the screw and tighten the locknut (d). With the use of the Kaldewei sound insulation set, and provided installation is effected properly, the requirements of DIN 4109/A1 are fulfilled.
Baths must also be mounted with bath anchors (not included in the scope of delivery).
d
a
page 4 of 4
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
Top Related