8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 1/16
PSK Standardisointi STANDARDI PSK 4230
PSK Standards Association E0H1A 2. painos/2nd editionCOPYRIGHT: PSK Standardisointiyhdistys ry 2010-11-18 1 (16)
MYYNTI: PSK Standardisointiyhdistys ry, PUH. (09) 72 880 880WWW-OSOITE: www.psk-standardisointi.fi, SÄHKÖPOSTI [email protected]
Korvaa standardin PSK 4230:2008Replaces the standard PSK 4230:2008
PUTKILUOKKA E0H1A PAINELAITEKÄYTTÖÖN. AUSTENIITTINEN RUOSTUMATON CrNi-TERÄS.Pipe class E0H1A for pressure purposes. Austenitic stainless CrNi-steel
Ristiriitatapauksissa pätee suomenkielinen teksti In the case of a conflict the Finnish text shall prevail.
Sisällys1 Soveltamisala2 Viittaukset3 Materiaalit4 Mitat5 Putkiluokan sallitut käyttöpaineet ja
lämpötilatOpastavia tietojaO.1 LaskentaperusteetO.2 Nimikkeen muodostaminenO.3 Putkiluokan tunnusO.4 Muutokset standardin edelliseen painokseen
Contents1 Scope2 References3 Materials4 Dimensions5 The allowable operating pressures and tem-
peraturesInformation for guidanceO.1 Calculation criteriaO.2 Forming of designationO.3 Identification of the pipe classO.4 Amendments to the previous edition of the
standard
1 SOVELTAMISALA 1 SCOPE
Tässä standardissa esitetään putkiluokkaanE0H1A kuuluvien painelaitekäyttöön tarkoitettujenputkien ja putkenosien materiaalit, mitat ja putki-
luokan paineenkestävyys. Tämän putkiluokan suu-rin sallittu paine on 6 bar lämpötilassa 20 ºC jasuurin sallittu lämpötila 400 ºC.
This standard specifies the materials and dimen-sions of the pipes and fittings belonging to the pipeclass E0H1A, as well as the pressure rating of the
pipe class. In this pipe class the allowable pres-sure at temperature 20 ºC is 6 bar and the maxi-mum allowable temperature 400 ºC.
Putkiluokkien määrittely on esitetty standardissaPSK 4201 ja lisäksi standardeissa SFS-EN 13480-2…5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia.
The definition of the pipe classes is introduced instandard PSK 4201. Additional requirements to betaken into account in piping design and manufac-turing are defined in standards SFS-EN 13480parts 2…5.
2 VIITTAUKSET 2 REFERENCES
PSK 4201 Putkiluokat. Määrittely. 2007 PSK 4201 Pipe classes. Definition. 2007
SFS-EN 1092-1 Laipat ja laippaliitokset. Pyöreätlaipat putkille, venttiileille, yhteille ja varusteille,PN-mitoitetut. Osa 1: Teräksiset laipat. 2007.
SFS-EN 1092-1 Flanges and their joints - Circularflanges for pipes, valves, fittings and accessories,PN designated - Part 1: Steel flanges. 2007.
SFS-EN 1514-1 Flanges and their joints. Di-mensions of gaskets for PN-designated flanges.Part 1: Non-metallic flat gaskets with or withoutinserts. 1997.
SFS-EN 1514-1 Flanges and their joints. Dimen-sions of gaskets for PN-designated flanges. Part 1:Non-metallic flat gaskets with or without inserts.1997.
SFS-EN 10025-2 Kuumavalssatut rakenneteräk-set. Osa 2: Seostamattomat rakenneteräkset. Tek-
niset toimitusehdot. 2004.
SFS-EN 10025-2 Hot rolled products of struc-tural steels. Part 2: Technical delivery conditions
for non-alloy structural steels. 2004.
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 2/16
PSK Standardisointi PSK 4230
E0H1A2 (16)
SFS-EN 10028-2 Painelaiteteräkset. Levy-tuotteet. Osa 2: Kuumalujat seostamattomat jaseosteräkset. 2003.
SFS-EN 10028-2 Flat products made of steelsfor pressure purposes. Part 2: Non-alloy and alloysteels with specified elevated temperature proper-ties. 2003.
SFS-EN 10028-7 Painelaiteteräkset. Levy-tuotteet. Osa 7: Ruostumattomat teräkset. 2007.
SFS-EN 10028-7 Flat products made of steelsfor pressure purposes. Part 7: Stainless steels.2007.
SFS-EN 10204 Metallituotteiden ainestodis-tukset. 2004.
SFS-EN 10204 Metallic products. Types of inspec-tion documents. 2004.
SFS-EN 10217-7 Hitsatut painelaiteteräsputket.Tekniset toimitusehdot. Osa 7: Ruostumattomatteräsputket. 2005.
SFS-EN 10217-7 Welded steel tubes for pres-sure purposes. Technical delivery conditions. Part7: Stainless steel tubes 2005.
SFS-EN 10222-5 Painelaiteteräkset. Takeet.
Osa 5: Martensiittiset, austeniittiset ja austeniittis-ferriittiset ruostumattomat teräkset. 2000.
SFS-EN 10222-5 Steel forgings for pressure
purposes. Part 5: Martensitic, austenitic and aus-tenitic-ferritic stainless steels. 2000.
SFS-EN 10241 Steel threaded pipe fittings.2000.
SFS-EN 10241 Steel threaded pipe fittings.2000.
SFS-EN 10253-4 Butt-welding pipe fittings-Part 4:Wrought austenitic and austenitic-ferritic (duplex)stainless steels with specific inspection require-ments. 2008.
SFS-EN 10253-4 Butt-welding pipe fittings-Part 4:Wrought austenitic and austenitic-ferritic (duplex)stainless steels with specific inspection require-ments. 2008.
SFS-EN 10269 + A1 Teräkset ja nikkeliseoksetkorotetuissa ja/tai matalissa lämpötiloissa käytettä-
viin kiinnittimiin. 2006.
SFS-EN 10269 + A1 Steels and nickel alloys forfasteners with specified elevated and/or low tem-
perature properties. 2006.
SFS-EN 10272 Painelaiteteräkset. Ruostumat-tomat terästangot. 2007.
SFS-EN 10272 Stainless steel bars for pressu-re purposes. 2007.
SFS-EN 13480-2 Metalliset teollisuusputkistot.Osa 2: Materiaalit. 2010
SFS-EN 13480-2 Metallic industrial piping. Part 2:Materials. 2010
SFS-EN 13480-3 Metalliset teollisuusputkistot.Osa 3: Suunnittelu ja laskenta. 2010
SFS-EN 13480-3 Metallic industrial piping. Part3: Design and calculation. 2010
SFS-EN 13480-4 Metalliset teollisuusputkistot.Osa 4: Valmistus ja asennus. 2010
SFS-EN 13480-4 Metallic industrial piping. Part4: Fabrication and installation. 2010
SFS-EN 13480-5 Metalliset teollisuusputkistot.Osa 5: Tarkastus ja testaus. 2010
SFS-EN 13480-5 Metallic industrial piping. Part5: Inspection and testing. 2010
SFS-EN 20898-2 Kiinnityselinten lujuusominai-suudet. Osa 2: Mutterit. Metrinen kierre. 1994.
SFS-EN 20898-2 Mechanical properties of fas-teners. Part 2: Nuts with specified proof load val-ues. Coarse thread. 1994.
SFS-EN ISO 898-1 Kiinnityselimien lujuusomi-naisuudet. Seostamattomat ja seosteräkset. Osa1: Ruuvit ja vaarnaruuvit. 2000.
SFS-EN ISO 898-1 Mechanical properties of fas-teners made of carbon steel and alloy steel. Part 1:Bolts, screws and studs. 2000.
SFS-EN ISO 4014 Hexagon head bolts. Product
grades A and B. 2001.
SFS-EN ISO 4014 Hexagon head bolts. Product
grades A and B. 2001.
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 3/16
PSK Standardisoint i PSK 4230
E0H1A3 (16)
SFS-EN ISO 4032 Hexagon nuts, style 1. Prod-uct grades A and B. 2001.
SFS-EN ISO 4032 Hexagon nuts, style 1. Productgrades A and B. 2001.
SFS-EN ISO 7089 Plain washers. Normal series.Product grades A. 2001.
SFS-EN ISO 7089 Plain washers. Normal series.Product grade A. 2001.
3 MATERIAALIT 3 MATERIALS
Tähän putkiluokkaan kuuluvien DN10…DN1200putkien materiaali on austeniittinen ruostumatonteräs 1.4307 (X2CrNi 18-9) SFS-EN 10217-7.
The material of pipes DN 10 ... DN 1200 belongingto this pipe class is austenitic steel 1.4307 (X2CrNi18-9) SFS-EN 10217-7.
Käyrien, kartioiden, T-putkien, päätyjen ja putki-kaulusten materiaali on austeniittinen ruostumatonteräs 1.4307 (X2CrNi 18-9), SFS-EN 10253-4.
The material of elbows, reducers, tees, caps andcollars is austenitic steel 1.4307 (X2CrNi 18-9),SFS-EN 10253-4.
Muiden putkiluokkaan kuuluvien osien materiaalit
on esitetty taulukossa 3.
The materials of other components belonging to
this pipe class are specified in Table 3.
Tämä standardi esittää mitat putkille ja putken osil-le perustuen yhdenmukaistettuihin EN-standardeihin, joissa hitsausliitoksen lujuuskertoi-mena on 1,0. Nimelliskoot ≥ DN 450 on kuitenkintarkistettu myös käyttäen lujuuskerrointa 0,7. Mikälikäytetään lujuuskerrointa 0,7, on otettava huomi-oon, että materiaalien osalta ei saa viitata tässästandardissa esitettyihin viitestandardeihin. Tällöintulee noudattaa PED-luokissa I...III (KTMp938/1999) olennaisia turvallisuusvaatimuksia jaesittää perusteet materiaalien hyväksyttävyydelle
(esim. SFS-EN 10028-7 mukainen materiaali onhyväksyttävissä ilman erityisarviointia). Lisäksivaaditaan selvitykset hitsausmenetelmien, hitsaaji-en ja hitsausoperaattorien pätevöinnistä ja hyväk-synnästä sekä lisäksi luokassa III selvitykset NDT-tarkastajien hyväksynnästä.
This standard presents dimensions for pipes andpipe fittings based on harmonized EN-standardsaccording to which the weld joint coefficient is 1,0.However nominal sizes ≥ DN 450 have beenchecked using joint coefficient of 0,7. In case jointcoefficient 0,7 is used it shall be taken into accountthat no reference to referenced material standardpresented in this standard is allowed. In that caseessential safety requirements shall be followed inPED categories I…III (KTMp 938/1999) and a justi-fication for material acceptability demonstrated (for
example the material according to SFS-EN 10028-7 is acceptable without particular material ap-praisal). Additionally qualification documents andacceptance of welding methods, welders and weld-ing operators as well as qualification and accep-tance of NDT-inspectors in category III are re-quired.
Putkille, putkenosille ja laipoille vaaditaan standar-din SFS-EN 10204 mukainen ainestodistus 3.1,mistä tulee ilmetä, että materiaalin valmistajalla onEuroopan yhteisöön sijoittuneen toimivaltaisen eli-men sertifioima laatujärjestelmä, joka kattaa kysei-sen materiaalityypin valmistamisen. Muiden putki-luokkaan kuuluvien komponenttien ainestodistus-vaatimukset on esitetty taulukossa 3.
Material certificate 3.1 according to standard SFS-EN 10204 is required for pipes, fittings andflanges. The certificate shall demonstrate that themanufacturer of the material has a quality systemcertified by an authorized body in EU, which cov-ers manufacturing of the material type in question.The requirements of material certificates for theother components belonging to this pipe class arespecified in Table 3.
Tilauksessa on huomioitava, että standardin SFS-EN 10217-7 mukaan merkinnällä C1 varustettuaputkea saa käyttää korkeintaan luokkaan I kuulu-viin putkistoihin ja merkinnällä C2 varustettua put-kea korkeintaan luokkaan II kuuluviin putkistoihin.
When ordering it shall be taken into account thataccording to standards SFS-EN 10217-7 the pipesmarked with C1 are allowed to be used in pipingbelonging to category I at the most. The pipesmarked with C2 are allowed to be used in categoryII at the most.
Putkenosien mukana on lisäksi toimitettava valmis-tajan laatima todistus, josta selviää standardinSFS-EN 10253-4 vaatimat valmistustiedot.
Additionally, manufacturer's certificate specifyingthe manufacturing information according to stan-dard SFS-EN 10253-4 shall be delivered with thepipe fittings.
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 4/16
PSK Standardisointi PSK 4230
E0H1A4 (16)
4 MITAT 4 DIMENSIONS
Putkiluokkaan E0H1A kuuluvien putkien ja put-kenosien mitat ja mittastandardit on esitetty taulu-koissa 1, 2 ja 3.
The dimensions and standards of pipes and fittingsbelonging to the pipe class E0H1A are shown inTables 1, 2 and 3.
Kaikki putkenosat ovat standardiehdotuksen SFS-EN 10253-4 tyyppiä A, joilla seinämänpaksuus onsama liitospäissä ja osan keskellä. Seinämän-paksuudet voidaan joutua tarvittaessa viistämäänhitsauspäissä vastaamaan liittyvää komponenttia.
All pipe fittings are of type A according to standardSFS-EN 10253-4. Their wall thickness is the samein weld ends and in the middle of the fitting. Itmight be necessary to bevel the wall at weld endsto correspond the connected component.
Muotokappaleiden seinämänpaksuudet taulukossa1 voivat poiketa standardissa SFS-EN 10253-4esitetyistä paksuuksista.
Wall thicknesses of the pipe fittings in Table 1 maydeviate from those specified in SFS-EN 10253-4.
Taulukko 1 Putkien, käyrien, päätyjen, kartioiden ja T-putkien mitat (mm)Table 1 The dimensions of pipes, elbows, caps, reducers and tees (mm)
Putki
Pipe
Käyrä
Elbow
Pääty
Cap
SFS-EN10217-7
SFS-EN10253-4 SFS-EN10253-4
Kartio
Reducer
T-putki
Tee
SFS-EN 10253-4 SFS-EN 10253-4
Nimellis-koko
Ulko-halkaisija
Putki Käyrä Pääty Nimellis-koko
Ulko-halkaisija
Kartio1)
T-putki
Nominalsize
Outerdiameter
Pipe Elbow Cap Nominalsize
Outerdiameter
Reducer1)
Tee
DN D T T R2) T K DN1 D1 T T1 L T T1 F G
10 17,2 1,6 1,6 38 - - - - - - - - - - -
15 21,3 1,6 2 28 1,6 25 15 21,3 - - - 1,6 1,6 25 25
10 17,2 2 - 12 - - - -
20 26,9 1,6 2 29 1,6 25 20 26,9 - - - 1,6 1,6 29 29
15 21,3 2 - 17 1,6 1,6 29 29
10 17,2 2 - 29 - - - -
25 33,7 1,6 2 38 1,6 38 25 33,7 - - - 1,6 1,6 38 38
20 26,9 2 - 20 1,6 1,6 38 38
15 21,3 2 - 37 1,6 1,6 38 38
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 5/16
PSK Standardisoint i PSK 4230
E0H1A5 (16)
Nimellis-koko
Ulko-halkaisija
Putki Käyrä Pääty Nimellis-koko
Ulko-halkaisija
Kartio1)
T-putki
Nominalsize Outerdiameter Pipe Elbow Cap Nominalsize Outerdiameter Reducer1)
Tee
DN D T T R2) T K DN1 D1 T T1 L T T1 F G
32 42,4 1,6 2 48 1,6 38 32 42,4 - - - 1,6 1,6 48 48
25 33,7 2 - 26 1,6 1,6 48 48
20 26,9 2 - 46 1,6 1,6 48 48
15 21,3 - - - 1,6 1,6 48 48
40 48,3 1,6 2 57 1,6 38 40 48,3 - - - 1,6 1,6 57 57
32 42,4 2 - 17 1,6 1,6 57 57
25 33,7 2 - 43 1,6 1,6 57 57
20 26,9 2 - 63 1,6 1,6 57 57
50 60,3 1,6 2 76 1,6 38 50 60,3 - - - 1,6 1,6 125 125
40 48,3 2 - 36 1,6 1,6 125 125
32 42,4 2 - 53 1,6 1,6 125 125
25 33,7 2 - 79 1,6 1,6 125 125
20 26,9 2 - 99 - - - -
65 76,1 1,6 2 95 1,6 38 65 76,1 - - - 1,6 1,6 140 140
50 60,3 2 - 47 1,6 1,6 140 140
40 48,3 2 - 82 1,6 1,6 140 140
32 42,4 2 - 100 1,6 1,6 140 140
25 33,7 2 - 126 - - - -
80 88,9 2 2 114 2 51 80 88,9 - - - 2 2 150 150
65 76,1 2 - 38 2 1,6 150 150
50 60,3 2 - 85 2 1,6 150 150
40 48,3 2 - 120 2 1,6 150 150
32 42,4 2 - 138 - - - -
100 114,3 2 2 152 2 64 100 114,3 - - - 2 2 160 160
80 88,9 2 - 75 2 2 160 160
65 76,1 2 - 113 2 1,6 160 160
50 60,3 2 - 160 2 1,6 160 160
40 48,3 2 - 195 - - - -
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 6/16
PSK Standardisointi PSK 4230
E0H1A6 (16)
Nimellis-koko
Ulko-halkaisija
Putki Käyrä Pääty Nimellis-koko
Ulko-halkaisija
Kartio1)
T-putki
Nominalsize Outerdiameter Pipe Elbow Cap Nominalsize Outerdiameter Reducer1)
Tee
DN D T T R2) T K DN1 D1 T T1 L T T1 F G
125 139,7 2 2 190 2 76 125 139,7 - - - 2 2 180 180
100 114,3 2 - 75 2 2 180 180
80 88,9 2 - 151 2 2 180 180
65 76,1 2 - 188 2 1,6 180 180
50 60,3 2 - 235 - - - -
150 168,3 2 2 229 2 89 150 168,3 - - - 2 2 200 200
125 139,7 2 - 85 2 2 200 200
100 114,3 2 - 160 2 2 200 200
80 88,9 2 - 235 2 2 200 200
65 76,1 2 - 273 - - - -
200 219,1 2,6 2,6 305 2,6 102 200 219,1 - - - 2,6 2,6 250 250
150 168,3 2,6 - 150 2,6 2 250 250
125 139,7 2,6 - 235 2,6 2 250 250
100 114,3 2,6 - 310 2,6 2 250 250
80 88,9 2,6 - 385 - - - -
250 273 3,2 3,2 381 3,2 127 250 273 - - - 3,2 3,2 300 300
200 219,1 3,2 - 160 3,2 2,6 300 300
150 168,3 3,2 - 310 3,2 2 300 300
125 139,7 3,2 - 395 3,2 2 300 300
100 114,3 3,2 - 470 - - - -
300 323,9 3,2 3,2 457 3,2 152 300 323,9 - - - 3,2 3,2 330 330
250 273 3,2 - 151 3,2 3,2 330 330
200 219,1 3,2 - 310 3,2 2,6 330 330
150 168,3 3,2 - 461 3,2 2 330 330
125 139,7 3,2 - 545 - - - -
350 355,6 3,2 3,2 533 3,2 165 350 355,6 - - - 4 4 360 360
300 323,9 3,2 - 94 4 3,2 360 360
250 273 3,2 - 244 4 3,2 360 360
200 219,1 3,2 - 404 4 2,6 360 360
150 168,3 3,2 - 554 - - - -
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 7/16
PSK Standardisoint i PSK 4230
E0H1A7 (16)
Nimellis-koko
Ulko-halkaisija
Putki Käyrä Pääty Nimellis-koko
Ulko-halkaisija
Kartio1)
T-putki
Nominalsize
Outerdiameter
Pipe Elbow Cap Nominalsize
Outerdiameter
Reducer1)
Tee
DN D T T R2) T K DN1 D1 T T1 L T T1 F G
400 406,4 3,2 3,2 610 3,2 178 400 406,4 - - - 4 4 400 400
350 355,6 3,2 - 150 4 4 400 400
300 323,9 3,2 - 244 4 3,2 400 400
250 273 3,2 - 395 4 3,2 400 400
200 219,1 3,2 - 554 - - - -
450 457 3,2 3,2 686 3,2 203 450 457 - - - 5 5 450 450
400 406,4 3,2 - 150 5 4 450 450
350 355,6 3,2 - 301 5 3,2 450 450
300 323,9 3,2 - 395 5 3,2 450 450
250 273 3,2 - 545 - - - -
500 508 4 4 762 4 229 500 508 - - - 5 5 500 500
450 457 4 - 150 5 5 500 500
400 406,4 4 - 301 5 4 500 500
350 355,6 4 - 451 5 3,2 500 500
300 323,9 4 - 545 - - - -
600 610 4 4 914 4 267 600 610 - - - 6,3 6,3 600 600
500 508 4 - 301 6,3 5 600 600
450 457 4 - 451 6,3 4 600 600
400 406,4 4 - 601 6,3 3,2 600 600
350 355,6 4 - 752 - - - -
700 711 4 4 1067 4 267 700 711 - - - 8 8 700 700
600 610 4 - 301 8 5 700 700
500 508 4 - 601 8 4 700 700
450 457 4 - 752 8 4 700 700
400 406,4 4 - 902 - - - -
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 8/16
PSK Standardisointi PSK 4230
E0H1A8 (16)
Nimellis-koko
Ulko-halkaisija
Putki Käyrä Pääty Nimellis-koko
Ulko-halkaisija
Kartio1)
T-putki
Nominalsize Outerdiameter Pipe Elbow Cap Nominalsize Outerdiameter Reducer1)
Tee
DN D T T R2) T K DN1 D1 T T1 L T T1 F G
800 813 4 4 1219 4 267 800 813 8 8 800 800
700 711 4 - 301 8 8 800 800
600 610 4 - 601 8 6,3 800 800
500 508 4 - 902 8 4 800 800
450 457 4 - 1053
900 914 4 5 1372 4 267 900 914 - - - 10 10 900 900
800 813 5 - 301 10 8 900 900
700 711 5 - 601 10 6,3 900 900
600 610 5 - 902 10 5 900 900
500 508 5 - 1203 - - - -
1000 1016 5 6,3 1524 5 305 1000 1016 - - - 10 10 1000 1000
900 914 6,3 - 301 10 10 1000 1000
800 813 6,3 - 601 10 8 1000 1000
700 711 6,3 - 902 10 6,3 1000 1000
600 610 6,3 - 1203 - - - -
1200 1220 6,3 - - - - 1200 1220 - - - - - - -
1000 1016 6,3 - 604 - - - -
900 914 6,3 - 905 - - - -
800 813 6,3 - 1205 - - - -
1) Mitat koskevat myös epäkeskeisiä kartioita. 2) Putkikoossa DN 10 käytetään putkitaivutusta.1) The dimensions apply also to eccentric reducers. 2) For size DN 10 a pipe bend is used.
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 9/16
PSK Standardisoint i PSK 4230
E0H1A9 (16)
Taulukko 2 Laippojen mitatTable 2 The dimensions of flanges
PN 10
SFS-EN 1092-1tyyppi 11type 11
tyyppi 02 & 35type 02 & 35
Ruuvit
Bolts
Sokeointilevy
Spade
Umpilaipanvuorauslevy
Lining plate forblind flangeDN D K
MääräQuantity
KokoSize
H2 C2 H4 C1 F
d1)
s d1)
s
10 90 60 4 12 35 16 35 14 5 46 5 46 2
15 95 65 4 12 38 16 38 14 5 51 5 51 2
20 105 75 4 12 40 18 40 16 6 61 5 61 2
25 115 85 4 12 40 18 40 16 7 71 5 71 2
32 140 100 4 16 42 18 42 18 8 82 5 82 2
40 150 110 4 16 45 18 45 18 8 92 5 92 2
50 165 125 4 16 45 18 45 20 8 107 5 107 2
65 185 145 8 16 45 20 8 127 5 127 280 200 160 8 16 50 20 10 142 5 142 2
100 220 180 8 16 52 22 10 162 5 162 2
125 250 210 8 16 55 22 10 192 8 192 2
150 285 240 8 20 55 24 10 218 8 218 2
200 340 295 8 20 62 24 11 273 8 273 2
250 395 350 12 20 68 26 12 328 10 328 2
300 445 400 12 20 68 26 12 378 12 2) 378 2
350 505 460 16 20 68 30 13 438 12 2) 438 2
400 565 515 16 24 72 32 14 489 15 2) 489 2
450 615 565 20 24 72 36 15 539 15 2) 539 2
500 670 620 20 24 75 38 16 594 20 2) 594 2
600 780 725 20 27 80 42 18 695 20 2) 695 2
700 895 840 24 27 80 50 20 810 25 2) 810 2
800 1015 950 24 30 90 56 20 917 25 2) 917 2
900 1115 1050 28 30 95 62 22 1017 30 2) 1017 2
1000 1230 1160 28 33 95 70 24 1124 30 2) 1124 2
1200 1455 1380 32 36 115 83 26 1341 35 2) 1341 21) Ulkohalkaisija d = tiivisteen ulkohalkaisija2)
Yleensä on taloudellisempaa valmistaa paksu sokeointilevy seostamattomasta teräksestä ja käyttää ruostu-mattomasta teräksestä tehtyjä vuorauslevyjä.1) Outer diameter d = outer diameter of the gasket2) Usually it is more economic to make a thick spade from non alloy steel plate and use stainless steel liningplates.
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 10/16
PSK Standardisointi PSK 4230
E0H1A10 (16)
Taulukko 3 Laippojen, umpilaippojen, kierteellisten putkenosien, ruuvien, muttereiden, aluslaattojen ja tiivis-teiden mittastandardit ja materiaalitTable 3 The dimension standards and materials of flanges, blind flanges, threaded pipe fittings, bolts, nuts,washers and gaskets
PutkenosaComponent
MittastandardiDimension standard
Materiaali
NimikeDesignation
StandardiStandard
TodistusCertifica-te
Irtolaippa PN 10 1)
Loose flange PN 10 1) SFS-EN 1092-1, tyyppi 02SFS-EN 1092-1, type 02
P265GH SFS-EN 10028-2 3.1
Kauluslaippa PN 10 2)
Welding neck flange PN 102)
SFS-EN 1092-1, tyyppi 11-B1SFS-EN 1092-1, type 11-B1
1.4307 SFS-EN 10222-5 3.1
Umpilaippa PN 10 1)
Blind flange PN 10 1) SFS-EN 1092-1, tyyppi 05SFS-EN 1092-1, type 05
P265GH SFS-EN 10028-2 3.1
Kaulus PN 10Collar PN 10
SFS-EN 1092-1, tyyppi 35SFS-EN 1092-1, type 35
1.4307 6) 3.1
SokeointilevySpade
- 1.4307 SFS-EN 10028-7 3.1
Kierteelliset putkenosat 7, 8)
Threaded pipe fittings 7, 8) SFS-EN 10241 1.4432 SFS-EN 10272 3.1
Umpilaipan vuorauslevyLining plate
- 1.4432 SFS-EN 10028-7 3.1
JäykisterengasStiffening ring - 1.4307 SFS-EN 10028-7 3.1
Ruuvi 3)
Bolt 3) SFS-EN ISO 4014 5.6 5) (T ≤ 300 oC)
25CrMo4SFS-EN ISO 898-1SFS-EN 10269+A1
2.23.1
Mutteri 3)
Nut 3) SFS-EN ISO 4032 5 (T ≤ 300 oC)
C35ESFS-EN 20898-2SFS-EN 10269+A1
2.23.1
Aluslaatta 3)
Washer 3) SFS-EN ISO 7089 Gr. A S235JR tai
vastaava SFS-EN 10025-2 -
Tiiviste PN 10Gasket PN 10
SFS-EN 1514-1, tyyppi IBCSFS-EN 1514-1, type IBC
4) - -
1)
Kuumasinkitty2) Kustannussyistä vaihtoehto pienillä putkihalkaisijoilla (yleensä DN10…DN50).3) Pintakäsittely on kuumasinkitys.4) Tiivisteen materiaali määritellään virtaavan aineen ja prosessiolosuhteiden perusteella.5) Materiaali vaatii erityisarvioinnin (PMA), katso standardi PSK 4201.6) Materiaalin valmistusmuoto (levy, tae jne.) ja vastaava standardi määrätään tarvittaessa.7) Osissa tai niiden pakkauksissa tulee olla merkinnät, joiden perusteella osat voidaan yhdistää niitä koskeviinmateriaalin valmistajan antamiin materiaalitodistuksiin.8) Kierteellisten putkenosien suurin suositeltava nimelliskoko on enintään DN50.1) Hot dip galvanized.2) For economic reasons this is an alternative in small bore piping (generally DN10…DN50).3) The surface treatment is hot-dip galvanizing.4) The gasket material is determined by the flowing fluid and process conditions.5)
The material requires a particular material appraisal (PMA), see standard PSK 4201.6) Raw material (plate, forging etc.) and respective standard shall be defined if necessary.7) The fittings or their packages must have markings, by which the fittings can be connected to related materialcertificates given by the supplier.8) The maximum recommended size for threaded pipe fittings is DN50.
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 11/16
PSK Standardisoint i PSK 4230
E0H1A11 (16)
5 PUTKILUOKAN SALLITUT KÄYTTÖPAI-NEET JA LÄMPÖTILAT
5 THE ALLOWABLE OPERATING PRES-SURES AND TEMPERATURES OF THEPIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kestä-mään 6 bar ylipaine 20 ºC lämpötilassa ja suurinsallittu lämpötila on 400 ºC. Alipaineen kesto 150 ºClämpötilassa sekä tarvittavien jäykisterenkaidenmitat on esitetty taulukossa 5.
The pipes and fittings belonging to this pipeclass have been designed to resist 6 bar over-pressure in 20 °C temperature and the maxi-mum allowable temperature is 400 ºC. Resis-tance of external pressure in 150 °C and dimen-sions of required stiffening rings are shown inTable 5.
Putkiluokan paineenkestävyys (poikkeuksena istu-tettu haaroitus) eri lämpötiloissa on esitetty kuvas-sa 1.
The pressure resistance of the pipe class (ex-cept branch connection) in different tempera-tures is shown in Figure 1.
Istutetun kohtisuoran haaroituksen paineenkestä-vyys eri lämpötiloissa saadaan kertomalla taulukon4 arvo kuvasta 1 saatavan sallitun paineen ja putki-luokan nimellispaineen (PN 6) suhteella.
The pressure resistance of a perpendicularbranch connection in different temperatures iscalculated by multiplying the value from Table 4with the ratio of the allowable pressure from Fig-ure 1 and the nominal pressure (PN 6).
Yli 400 oC lämpötiloissa mitoitukset ja materiaalienkelpoisuudet on erikseen tarkistettava.
In temperatures over 400 °C the dimensioningand the acceptability of the materials must bechecked separately.
Materiaalin 1.4307 raerajakorroosion vastuskyky ontestattu vain lämpötilaan 350 oC saakka (SFS-EN10217-7, taulukko 8), joten korkeampiin lämpötiloi-
hin tarkoitetun putkiston käyttöikää mietittäessätämä on huomioitava.
Susceptibility to intergranular corrosion of mate-rial 1.4307 is tested only up to temperature 350oC (SFS-EN 10217-7, Table 8) which should be
taken into account when estimating the total lifetime of the piping intended to higher tempera-tures.
Putkiluokan alin sallittu käyttölämpötila on -10 °C,edellyttäen, että 5.6 ruuvit täyttävät SFS-EN 13480-2 kohdan B.2.2.3 vaatimukset (tarvitaan materiaalinerityisarviointi, PMA).
The lowest allowable operating temperature ofthe pipe class is -10 °C, presuming that bolts ofstrength class 5.6 meet the requirements ofSFS-EN 13480-2 clause B.2.2.3 (particular ma-terial appraisal PMA is needed).
Mikäli alin sallittu lämpötila on alle -10 °C, niin ma-teriaalit on valittava siten, että standardin SFS-EN13480-2 Liitteen B vaatimukset täyttyvät.
In case the lowest allowable temperature is be-low -10 °C, the materials must be chosen so thatthe requirements of standard SFS-EN 13480-2,
Annex B, are met.
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 12/16
PSK Standardisointi PSK 4230
E0H1A12 (16)
6,0
5,6
5,3
5,1
4,8
4,54,3
4,14,0
3,83,7
3,5 3,5 3,4 3,3 3,2
0
1
2
3
4
5
6
7
20 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 °C
bar
Kuva 1 Sallitut paineet (bar) lämpötilan funktionaFigure 1 Allowable pressures (bar) as a function of temperature
Huomautus 1. Väliarvot interpoloidaan lineaarisesti.
Huomautus 2. Käyrän arvot on saatu putken, putkenosien ja laippojen materiaalistandardeissa kyseiseenlämpötilaan annetun myötörajan perusteella lasketun suunnittelujännityksen ja vastaavan huoneenlämpöti-laan määritetyn suunnittelujännityksen suhdeluvuista. Näistä suhdeluvuista pienin on kerrottu putkiluokannimellispaineella (PN 6).
Note 1. Intermediate values are linearly interpolated.Note 2.The values of the graph are calculated by the ratios of the design stress, based on the proofstrength value in the reference temperature from the material standards of pipe, fittings and flange and res-pectively the design stress in room temperature. The smallest value has been multiplied by the nominalpressure (PN 6).
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 13/16
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 14/16
PSK Standardisointi PSK 4230
E0H1A14 (16)
Taulukko 5 Jäykisterenkaiden jako, mitat ja suurin alipaine (bar) laskentalämpötilassa 150 oCTable 5 Pitch of stiffening rings, dimensions and allowable external pressure (bar) in calculation temperature150 oC
Nimellis-koko
Nominalsize
Ulko-halkaisija
Outerdiameter
Seinämänpaksuus
Wall thickness
Putken jäykistejako
Pitch of stiffeningrings
Jäykisteen 2) mitatStiffening ring 2) dimensions
Alipaineen kesto Allowable external
pressure
DN D T L hS ew pmax (bar)
10 17,2 1,6 - - - 1)
15 21,3 1,6 - - - 1)
20 26,9 1,6 - - - 1)
25 33,7 1,6 - - - 1)
32 42,4 1,6 - - - 1)
40 48,3 1,6 - - - 1)
50 60,3 1,6 - - - 1)
65 76,1 1,6 - - - 1)
80 88,9 2 - - - 1)
100 114,3 2 - - -1)
125 139,7 2 - - - 1)
150 168,3 2 - - - 1)
200 219,1 2,6 - - - 1)
250 273 3,2 - - - 1)
300 323,9 3,2 - - - 1)
350 355,6 3,2 3000 35 8
400 406,4 3,2 2700 40 8
450 457 3,2 2700 40 8
500 508 4 3400 50 8
600 610 4 2500 60 6
700 711 4 2300 60 6
800 813 4 1700 60 6
900 914 4 1400 60 6
1000 1016 5 2200 70 8
1200 1220 6,3 2900 90 81) Tässä nimelliskoossa putkiluokalle E0H1A sallitaan 1 bar alipaine ilman vahvistusrenkaita.2) Jäykisterenkaan hitsaus tehdään yleensä katkohitsein käyttäen joko vuoro- tai paripienahitsejä, jolloin hitsienyhteenlaskettujen pituuksien on oltava vähintään kolmannes kehän pituudesta jäykisteen kummallakin puolella.Hitsien jakomitta saa olla enintään 300 mm. Hitsin a-mitta on 0,7xT.1)
For this nominal size in pipe class E0H1A a vacuum (i.e. 1,0 bar external pressure) is allowed without stiffen-ing rings.2) Stiffening rings are usually welded using intermittent welds, either staggered intermittent or chain intermittentfillet welds where the total length of the welds shall be at least one third of the perimeter on both sides. The pitchof the welds shall not be more than 300 mm. Effective throat thickness of the weld is 0,7 x T.
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 15/16
PSK Standardisoint i PSK 4230
E0H1A15 (16)
OPASTAVIA TIETOJA INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet O.1 Calculation cri teria
Yleiset laskentaperusteet putkiluokan osille:
mitoitus SFS-EN 13480-3 mukaan ylipaine 0,6 MPa ja lämpötila 20 °C alipaine 0,1 MPa ja lämpötila 150 °C suunnittelujännitys f = 143 MPa (ylipaine) myötölujuus Rp0,2 = 132 MPa (alipaine) korroosiovara c0 = 0,0 mm hitsausliitoksen lujuuskerroin z = 1,0 DN < 400 hitsausliitoksen lujuuskerroin z = 0,7 DN > 400
General calculation criteria for piping componentsof the pipe class
dimensioning in accordance with SFS-EN13480-3
overpressure 0,6 MPa, temperature 20 °C external pressure 0,1 MPa, temperature 150 °C design stress f = 143 MPa (overpressure) proof strength Rp0,2 = 132 MPa (external pres-
sure) corrosion allowance c0 = 0,0 mm weld joint factor z = 1,0 DN < 400
weld joint factor z = 0,7 DN > 400
Osien seinämänpaksuuksille on käytetty seuraaviavalmistustoleransseja: putket
- 10 % tai vähintään 0,2 mm, kun DN < 1200 käyrät, kartiot, T-putket ja päädyt
- 12,5 %, kun DN < 600- 0,35 mm, kun DN > 600 ja T < 10,0 mm- 0,5 mm, kun DN > 600 ja T > 10,0 mm
The following manufacturing tolerances have beenused for the wall thickness of various components: pipes
- 10 % or at least 0,2 mm, when DN < 1200 elbows, reducers, tees and caps
- 12,5 %, when DN < 600- 0,35 mm, when DN > 600 and T < 10,0 mm- 0,5 mm, when DN > 600 and T > 10,0 mm
Kartioiden laskenta on tehty epäkeskeisille levykar-tioille.
The calculation of reducers has been done for ec-centric reducers.
O.2 Nimikkeen muodostaminen O.2 Forming of designation
Esimerkkejä nimikkeen muodostamisesta:
Putki 168,3x2,0 - SFS-EN 10217-7 - TC 1 - W1- 1.4307
Käyrä 168,3x2,0 – SFS-EN 10253-4 - tyyppi A -3D - 90o - 1.4307
Kartio E1) 219,1x2,6 – 168,3x2,6 - SFS-EN10253-4 - tyyppi A – Taul. A.6 - 1.4307
T-putki 219,1x2,6 – 168,3x2,0 - SFS-EN
10253-4 - tyyppi A – Taul. A.4 - 1.4307 Irtolaippa SFS-EN 1092-1 - tyyppi 02 - DN400
– PN10 - P265GH - SFS-EN 10028-2 Kaulus SFS-EN 1092-1 - tyyppi 35 - DN200 –
PN10 - 1.4307 Kauluslaippa SFS-EN 1092-1 - tyyppi 11 - B1 -
DN50 – PN10 - 1.4307 - EN 10222-5 Umpilaippa SFS-EN 1092-1 - tyyppi 05 -
DN400 – PN10 - P265GH - SFS-EN 10028-2 Pääty 219,1x2,6 - SFS-EN 10253-4 - tyyppi A -
1.4307 Tiiviste DN 100 – PN10 - tyyppi IBC - 2 mm -
SFS-EN 1514-12)
Examples of designations:
Pipe 168,3x2,0 - SFS-EN 10217-7 - TC 1 - W1- 1.4307
Elbow 168,3x2,0 – SFS-EN 10253-4 - type A -3D - 90o - 1.4307
Reducer E1) 219,1x2,6 – 168,3x2,6 - SFS-EN10253-4 - type A – Table A.6 - 1.4307
Tee 219,1x2,6 – 168,3x2,0 - SFS-EN 10253-4 -
type A – Table A.4 - 1.4307 Loose flange SFS-EN 1092-1 - type 02 -
DN400 – PN10 - P265GH - SFS-EN 10028-2 Collar SFS-EN 1092-1 - type 35 - DN200 –
PN10 - 1.4307 Welding neck flange SFS-EN 1092-1 - type 11 -
B1 - DN50 – PN10 - 1.4307 - EN 10222-5 Blind flange SFS-EN 1092-1 - type 05 - DN400
– PN10 - P265GH - SFS-EN 10028-2 Cap 219,1x2,6 - SFS-EN 10253-4 - type A -
1.4307 Gasket DN 100 – PN10 - type IBC - 2 mm -
SFS-EN 1514-12)
8/11/2019 PSK 4230 - Pipe Class E0H1A for Pressure Purposes. Austenitic Stainless CrNi-steel
http://slidepdf.com/reader/full/psk-4230-pipe-class-e0h1a-for-pressure-purposes-austenitic-stainless-crni-steel 16/16
PSK Standardisointi PSK 4230
E0H1A16 (16)
1) E = epäkeskeinen, K = keskeinen2) Tiivistemateriaalin valinta määräytyy virtaavanaineen ja prosessiolosuhteiden mukaan.
1) E = eccentric, K = concentric2) Selection of the gasket material shall be deter-mined by the fluid and process conditions.
O.3 Putkiluokan tunnus O.3 Identifi cation of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoit-taa, että putkiluokka noudattaa yhdenmukaistettujaeurooppalaisia standardeja ja se on olennainen osaputkiluokan merkintää.
The letter E in the beginning of the identification ofthe pipe class indicates that the pipe class complieswith the harmonized European standards and it isan integral part of the pipe class identification.
Putkiluokalle annetaan eri tunnus, jos sen sisältöpoikkeaa tässä standardissa esitetystä.
A different identification shall be given to the pipeclass if the contents deviate from this standard.
O.4 Muutokset standard in edelliseen pai-nokseen
O.4 Amendments to the previous edition ofthe standard
Tekstiä on tarkennettu. The text has been clarified.
Top Related