7/25/2019 Pre Insulated Pipe Supports Catalogue
1/206
PRE-INSULAPRE-INSULATED PIPE SUPPORTSTED PIPE SUPPORTSw w ww w w . p i p i n g t e c h . c o m. p i p i n g t e c h . c o m
C O L D S H O E S C RC O L D S H O E S C RY O S H O E S H O T S H O E SY O S H O E S H O T S H O E S
PIPING TECHNOLOGY & PRODUCTS, INCPIPING TECHNOLOGY & PRODUCTS, INC
7/25/2019 Pre Insulated Pipe Supports Catalogue
2/206
1 2
3
4
5
6
713-731-0030 713-731-8640 800-PTP-5914 [email protected] http://www.pipingtech.com/LOCAL PHONE FAX TOLL FREE OUTSIDETEXAS
PIPING TECHNOLOGY & PRODUCTS, INC. 01/9550M PRINTED IN U.S.A.
E MAIL WWW
7
1. AXIAL LOAD TEST OF A 3 LINE ANCHOR WITH PENOLIC & PUF INSULATION
2. PUF SUPERVISOR CHECKING INNER DIAMETER OF 48 SUPPORT.
3. GROUP PHOTO OF PT&PS MANAGEMENT, ENGINEERING AND MANUFACTUR-
ING TEAM.
4. SEMINAR FOR COLD SHOE INSTALLATION AT BP AMOCOS PLANT.
5. LINE ANCHOR WITH VERTICAL AND AXIAL LINE STOPS
6. 6 DROP-IN-PLACE LINE ANCHORS READY FOR SHIPMENT FOR POWER PLANT
IN PUERTO RICO.
7. BASE INSULATED SUPPORT WITH PHENOLIC & WOOD LAMINAR INSULATION.
7/25/2019 Pre Insulated Pipe Supports Catalogue
3/206
TABLE OF CONTENTS
GUIDED CRYOSHOES(CS-4000 series)
7624" - 42"CS-3033: Double-T BASE, unguided, without thrust plates
7424" - 42"CS-3032: Double-T BASE, unguided, with thrust plates
7224" - 42"CS-3031: Double-T BASE, guided, without thrust plates
7024" - 42"CS-3030: Double-T BASE, guided, with thrust plates
688" - 20"CS-3023: U-Type BASE, unguided, without thrust plates
668" - 20"CS-3022: U-Type BASE, unguided, with thrust plates
648" - 20"CS-3021: U-Type BASE, guided, without thrust plates628" - 20"CS-3020: U-Type BASE, guided, with thrust plates
601/2" - 6"CS-3013: Split-T BASE, unguided, without thrust plates
581/2" - 6"CS-3011: Split-T BASE, guided, without thrust plates
SLIDING CRYOSHOES(CS-3000 series)
5624" - 42"CS-2033: Double -T BASE, Stops and Structural Guide
5424" - 42"CS-2032: Double-T BASE, Bolted
5224" - 42"CS-2031: Double-T BASE, Stops and Guides
5024" - 42"CS-2030: Double-T BASE, Welded
488" - 20"CS-2023: U-Type BASE, Structural Stops and Guide
468" - 20"CS-2021: U-Type BASE, Stops and Guides
448" - 20"CS-2020: U-Type BASE, Welded
421/2" - 6"CS-2012: Split-T BASE, Bolted
401/2" - 6"CS-2011: Split-T BASE, Stops and Guides
381/2" - 6"CS-2010: Split-T BASE, Welded
ANCHOR TYPE CRYOSHOES(CS-2000 series)
3624" - 42"CS-1031: Double-T BASE, 360 insulation, with bolts
3424" - 42"CS-1030: Double-T BASE, 180 insulation, with bandstraps
328" - 20"CS-1021: U-Type BASE, 360 insulation, with bolts
308" - 20"CS-1020: U-Type BASE, 180 insulation, with bandstraps
281/2" - 6"CS-1011: Split-T BASE, 360 insulation, with bolts
261/2" - 6"CS-1010: Split-T BASE, 180 insulation, with bandstraps
241/2" - 42"CS-1001: Without BASE, 360 insulation
221/2" - 42"CS-1000: Without BASE, 180 insulationPage No.NPS RangeRESTING CRYOSHOES(CS-1000 series)
17CRYOSHOESelection Tree
195) Low Temperature Support Specifications
164) Foamglas153) Laminated Beechwood
122)Polyurethane/Polyisocynurate
101) Insulation Layering Information
Page No.TECHNICAL INFORMATION
II. PRE-INSULATED COLD SUPPORTS - CRYOSHOES
7B. Glossary of Terms & Definitions
4A. Company Introduction
Page No.I. INTRODUCTION
7/25/2019 Pre Insulated Pipe Supports Catalogue
4/206
1428" - 20"HS-2020: U-Type BASE, Welded
1401/2" - 6"HS-2012: Split-T BASE, Bolted
1381/2" - 6"HS-2011: Split-T BASE, Stops and Guides
1361/2" - 6"HS-2010: Split-T BASE, Welded
ANCHOR TYPE HOTSHOES(HS-2000 series)
13424" - 42"HS-1031: Double-T BASE, 360 insulation, with bolts
13224" - 42"HS-1030: Double-T BASE, 180 insulation, with bandstraps1308" - 20"HS-1021: U-Type BASE, 360 insulation, with bolts
1288" - 20"HS-1020: U-Type BASE, 180 insulation, with bandstraps
1261/2" - 6"HS-1011: Split-T BASE, 360 insulation, with bolts
1241/2" - 6"HS-1010: Split-T BASE, 180 insulation, with bandstraps
1221/2" - 42"HS-1001: Without BASE, 360 insulation
1201/2" - 42"HS-1000: Without BASE, 180 insulation
Page No.NPS RangeRESTING HOTSHOES(HS-1000 series)
18HOTSHOESelection Tree
1175) High Temperature Support Specifications
1164) Marinite1153) FireTemp1142) Foamglas1131) Calcium Silicate
Page No.TECHNICAL INFORMATION
III. PRE-INSULATED HOT SUPPORTS
112LOAD TESTING: LNG LAMINATED PHENOLIC BLOCK
111CS-6080: LNG Line Anchor Module
110CS-6070: Pre-Insulated Expansion Joint Module
108CS-6060: Foamglas - Polyurethane Hybrid Shoe
106CS-6050: Hanging Roller104CS-6040: Roller Type
102CS-6030: Dummy Leg, Phenolic Block
100CS-6020: Double Clamp Phenolic Support
98CS-6010: Pre-insulated Hanger Support - 360 insulation
MISC. CRYOSHOES(CS-6000 series)
96CS-5030: 360 insulation.
94CS-5020: 180 insulation.
92CS-5010: 90 insulation.
BASE INSULATED CRYOSHOES(CS-5000 series)
9024" - 42"CS-4031: Double-T BASE, 360 insulation, with bolts8824" - 42"CS-4030: Double-T BASE, 180 insulation, with bandstraps
868" - 20"CS-4021: U-Type BASE, 360 insulation, with bolts
848" - 20"CS-4020: U-Type BASE, 180 insulation, with bandstraps
821/2" - 6"CS-4011: Split-T BASE, 360 insulation, with bolts
801/2" - 6"CS-4010: Split-T BASE, 180 insulation, with bandstraps
78CS-4001: Without BASE
7/25/2019 Pre Insulated Pipe Supports Catalogue
5/206
202LOAD TESTING: LNG CRYOGENIC ANCHORS, GUIDES AND
SUPPORTS
200HS-6060: Foamglas - Polyurethane Hybrid Shoe
198HS-6050: Hanging Roller
196HS-6040: Roller Type
194HS-6030: Dummy Leg, Phenolic Block
192HS-6020: Double Clamp Phenolic Support
190HS-6010: Pre-insulated Hanger Support - 360 insulation
MISC. HOTSHOES(HS-6000 series)
18824" - 42"HS-4031: Double-T BASE, 360 insulation, with bolts
18624" - 42"HS-4030: Double-T BASE, 180 insulation, with bandstraps
1848" - 20"HS-4021: U-Type BASE, 360 insulation, with bolts
1828" - 20"HS-4020: U-Type BASE, 180 insulation, with bandstraps
1801/2" - 6"HS-4011: Split-T BASE, 360 insulation, with bolts
1781/2" - 6"HS-4010: Split-T BASE, 180 insulation, with bandstraps
176HS-4001: Without BASE
GUIDED HOTSHOES(HS-4000 series)
17424" - 42"HS-3033: Double-T BASE, unguided, without thrust plates
17224" - 42"HS-3032: Double-T BASE, unguided, with thrust plates
17024" - 42"HS-3031: Double-T BASE, guided, without thrust plates
16824" - 42"HS-3030: Double-T BASE, guided, with thrust plates
1668" - 20"HS-3023: U-Type BASE, unguided, without thrust plates
1648" - 20"HS-3022: U-Type BASE, unguided, with thrust plates
1628" - 20"HS-3021: U-Type BASE, guided, without thrust plates
1608" - 20"HS-3020: U-Type BASE, guided, with thrust plates
1581/2" - 6"HS-3013: Split-T BASE, unguided, without thrust plates
1561/2" - 6"HS-3011: Split-T BASE, guided, without thrust plates
SLIDING HOTSHOES (HS-3000 series)
15424" - 42"HS-2033: Double -T BASE, Stops and Structural Guide
15224" - 42"HS-2032: Double-T BASE, Bolted
15024" - 42"HS-2031: Double-T BASE, Stops and Guides
14824" - 42"HS-2030: Double-T BASE, Welded
1468" - 20"HS-2023: U-Type BASE, Structural Stops and Guide
Note: PT&P continuously improves its products and designs. Designs may be modified and/or altered without priornotification to our customers. Consult the PT&P website for current updates and news bulletins regarding our designs:www.pipingtech.com/
7/25/2019 Pre Insulated Pipe Supports Catalogue
6/206
ABOUT PIPING TECHNOLOGY & PRODUCTSPT&P was incorporated in Texas in 1978. In 1986 we acquired Sweco Fab, Inc.,an ASME Code pressure vessel shop to complementour product line. In 1988 the major manufacturing facilities of both companies moved to our present headquarters in Houston, Texas.PT&P acquired the metal expansion joint business of RM Engineered Products, Inc. of Ladson, SC in 1995. The machinery and
technology acquired provided the capability to manufacture thin-wall metal bellows. In 1997 PT&P acquired Ketema-U.S. BellowsofSan Diego, CA, another major manufacturer of metal bellows.
Today, Piping Technology & Products, and its wholly-owned subsidiaries, Sweco Faband U.S. Bellows are manufacturers of a widerange of products. The chart above shows the division of product lines between the three companies. Products manufactured by PT&Pand its subsidiaries include:
! pipe hangers and supports (variable andconstant load and big-tons)
! mechanical and hydraulic snubbers!!!! pre-insulated pipe supports (cryogenic
supports, coldshoes, hotshoes)
! instrument supports! Hold-down clamps for compressor systems
! expansion joints (metallic thin-wall, metallicthick-wall, fabric, rubber, slip-type)
! ASME code pressure vessels and tanks! spectacle/line blinds and orifice plates! pig launchers and receivers! slide bearings - Teflon, graphite, and
stainless steel
FACILITIES
Piping Technology & Products, Inc. and its wholly-owned subsidiaries, U.S. Bellows, Inc. and Sweco Fab, Inc., share engineering andmanufacturing resources at our 22-acre manufacturing facilityin Houston, Texas. PT&Ps manufacturing facilities are located near thePort of Houston, the largest port in the United States, for fast and convenient shipping around the world. PT&P/U.S. Bellows/Sweco have450,000 square feet of covered shopspace at our manufacturing facility in Houston.
As our long time customers know, after many years on Long Drive here in Houston, PT&P purchased 7.2 acres on Holmes Road inHouston, Texas in the summer of 1987. After upgrading the electrical systems, PT&P and Sweco Fab, Inc., PT&Ps ASME codefabrication shop, relocated to this new facility. Since that time, PT&P has continued to expand and improve our work space at ourHolmes Road Facility:
Piping Technology & Products- Pipe Supports
- engineered spring supports
- vibration control devices (snubbers, sway struts) - pre-insulated pipe supports
- fabricated pipe shoes
- clamps + misc. hardware
- Instrument Supports
- Anchors Bolts, Embed Plates
- Slide bearings-Teflon, graphite, Stainless Steal
Member of MSS, SPED, APFA
SWECO Fab, Inc.- Pressure Vessels- Pig-Launchers/Receivers- Spectacle/Line Blinds- Bellmouth Reducers- Misc. Fabrication
ASME U-Stamp
U.S. Bellows, Inc.- Expansion Joints - thin-wall metallic - rubber expansion joints - slip-type joints - thick-wallPending Membership to EJMA
7/25/2019 Pre Insulated Pipe Supports Catalogue
7/206
1991: PT&P adds a 17,000 square footwarehouse for storage of hardware and assembly components and a 6,000 square footpainting facility with modern environmental controls.
1992: PT&P obtains two adjacent properties, bringing our total plant area to 15.4 acres. This new space was used for theproduction of polyurethane components for cryogenic pipe shoes and as an assembly area for all pre-insulated pipe supports.
1995: PT&P Plant Expansion:100,000 square feet of covered shop space is added to PT&Ps existing facility. This additionalspace is used to receive and store raw materials and for staging and crating materials which are ready for shipment.
1999: PT&P Plant Expansion II: an additional 100,000 square feet of covered shop space increases PT&P manufacturing capacityfor 1) pre-insulated pipe supports, 2) expansion joint products, and 3) general fabrication.
PT&P extends an invitation to all of its customers to come to Houston and visit the plant. This is the best way to see our people, ourfacilities, and the many capabilities we have to serve you.
Our ProductsPiping Technology & Products, Inc. produces a wide variety of products that includes engineered spring hangers, constant supports,
hanger hardware, fabricated pipe and instrument supports, slide bearings using both Teflonand graphite, mechanical and hydraulicshock arrestors, insulated pipe supports and other items required for piping systems. PT&P produces all types of expansion joints forpiping and duct systems.
Our ASME code shop, Sweco Fab, Inc. fabricates pressure vessels, expansion joints which require code stamps, flow products such asorifice plates, line blinds, plate flanges, bleed rings, and strainers. Sweco Fab, Inc. is also a manufacturer of pipeline pig launchers and
receivers and SWEEGEEpigs.
U.S. Bellows, Inc. is the expansion joint division of PT&P -- in this division, a full line of expansion joint products are manufactured. Thisproduct line includes: fabric expansion joints, thick-wall metallic expansion joints, thin-wall metallic expansion joints, slip-type expansion
joints and rubber expansion joints. PT&P/U.S. Bellows has extensive experience designing and manufacturing products of this type perEJMA and ASME codes.
PT&P maintains a large inventory of critical components and other items required to supply emergency requirements. Rapid response toemergency orders is facilitated by computer software and databases of information required for the hundreds of items necessary forpiping systems of all sizes. Computer generated tags with bar codes are used to help field erection crews receive and identify items at
job sites.
PT&P has an active Quality Control program based on the ISO 9002 standard. Our catalogs provide details about our products and theirapplication.
7/25/2019 Pre Insulated Pipe Supports Catalogue
8/206
Pre-Insulated Pipe SupportsPT&P has been a major international supplier of pre-insulated pipe supports for more than 10 years for a variety of different applications:
" Liquefied Natural Gas (LNG) Plants" Liquefied Natural Gas (LNG) Pipelines" Liquefied Petroleum Gas (LPG)" Steam Water Pipelines" Chilled Water Pipelines" Chemical Plants
" Polypropylene Plants" Polyethylene Plants" Power Plants" Cogeneration Plants" Nitrogen Production Plants
Refer to the included Project List for a sample of projects on which PT&P has supplied insulated pipe supports. PT&P has conductedextensive testing of its pre-insulated pipe supports products such as load bearing tests including tests conducted at cryogenic conditions.Videos and test data of these tests are available from PT&P.
PT&Ps pre-insulated pipe supports department is devoted to the production of pipe insulation products for both hot and cold
applications. Polyurethane foam (PUF), Permali, Micarta, and Foamglasare all insulators used by PT&P in the manufacture of
coldshoes. Marinite, Foamglasand Calcium Silicate are the insulation medium used in the manufacture of hotshoes.
PT&Ps insulated pipe supports manufacturing department uses the following to produce the highest quality insulated pipe supportproducts:
" two automatic mixing machines which mix chemical elements to form polyurethane foam. One machine has acapacity of 180 lbs./minute and the other has a capacity of 80 lbs./minute output.
" Existing insulated pipe support molds of various sizes and configurations. Additionally, PT&P has the ability tofabricate its own molds which eliminates dependence on outside sources.
" Cutting saws with templates, drills, presses" Assembly areas, inspection areas, staging areas" shipping and crating areas
PT&P Electronic Data Interchange (EDI) Capabilities
Job/Quote Program
Currently, PT&P uses a software package called the Job/Quote Program to process all jobs that come into our shop. This softwarepackage, developed in-house, performs the take-off and generates all the applicable reports for manufacturing, accounting, andinventory. This software has the capability to take ASCII files as input. The layout of the ASCII file must be according to our programsspecifications. In instances where our customers wish to submit information to us electronically in another ASCII format or perhaps inanother data format entirely (Lotus 1-2-3, Microsoft Excel, Microsoft Access) our engineers will massage the data into the appropriateformat for input to our program.
Electronic Mail and the Internet
Piping Technology & Products, Inc. has full Internet electronic mail capabilities. E-mail can be sent and received by PT&P at theircompany-wide e-mail address, [email protected]. If necessary, individual accounts can also be setup for direct communicationbetween our customers and PT&P project engineers. Furthermore, if it proves to be useful, pertinent project information can bepublished to password-protected areas of PT&Ps website (located at http://www.pipingtech.com/), accessible around the world. In
general, PT&P has a very high-level functionality when it comes to operating and communicating on the Internet. PT&P is able to workwith its customers to apply these technologies so that PT&P and its customers benefit.
EDI Partnership
PT&P has an in-house software development team which handles, among other things, electronic data interchange issues. PT&P hasworked with its customers to leverage technology to improve workflow. PT&P actively encourages partnership with its customers toestablish EDI practices. EDI increases accuracy of information, reduces human error and significantly reduces the time required toprocess an order. We are ready to work with you in transmitting documents electronically.
7/25/2019 Pre Insulated Pipe Supports Catalogue
9/206
GLOSSARY OF TERMS & DEFINITIONS
Anchor A pipe support used to restrict the pipe movement at a particular location.
Axial Load The component of load acting along the length of a pipe exerted by the piping system during
its expansion, contraction, or movement.
Base The bottom component of a pipe support to uphold the piping system.
Bandstrap The metallic component of piping support wrapped around the protection shield to keep theassembly intact and provide the support necessary for friction.
Bolted The piping support assembly clamped together using bolts rather than bandstraps.
Calcium Silicate An incombustible insulation material utilized in hot supports.
Cell Size The average cell diameter in microns (m) (ASTM D2842)
Channel Clamp A special type of fabricated hold-down clamp consisting of two plates and bolted at threeplaces. (See PT&P standard drawing ICS-CC-100)
Closed Cell Content The percentage of foam consisting of closed no-interconnecting cells. (ASTM D2856)
Coldshoe A type of assembly used to give necessary support to a piping system while not dissipatingcryogenic temperatures of the piping system at a certain point.
Combustibility A measure of the resistance of a material to flame or high heat source. Laboratory testingmethods are not intended to reflect the hazards presented by rigid urethane foam or any othermaterial under actual fire conditions.
Compressive Strength The maximum compressive stress which a material is capable of sustaining. It is calculatedfrom the maximum load during a compression test and the original cross-sectional area of thespecimen. It is expressed in psi.(ASTM D1621)
Cryogenic A state of materials at very cold temperatures.
Dimensional Stability Change in dimensions of a specimen on exposure to various environments is calledDimensional Stability. It can be expressed as a % volume change or a linear change indimensions. (ASTM D2126)
Elastic Limit It is the greatest stress that a material is capable of sustaining without any permanent strainremaining after complete release of the stress.
Elongation The increase in gage length of a tension test specimen usually expressed as a percentage oforiginal gage length. (ASTM D1623)
Fabrication A process in which material is cut to certain size and molded into different required shapes.
FireTemp An incombustible insulation material having high density and compressive strength used in hot
supports.
Flexural Strength The maximum stress in the outer fiber at the moment of crack or break (expressed as psi)(ASTM D790)
Frothing Process A method of pouring the liquid ingredients of urethane foam in which partial extrusion takesplace before the polymerization reaction begins. In appearance, frothed foam is like shavingcream from an aerosol can.
Galvanizing An electromagnetic process of protecting metallic surfaces from corrosion or rust. Thisprocess is also known as electroplating.
7/25/2019 Pre Insulated Pipe Supports Catalogue
10/206
Gap The spacing at the junction of upper and lower cradles or clamps of the pipe shoe assembly.Guide A pipe support utilized to restrict the lateral movement of a piping system at a certain location.
Hanger A pipe support consisting of a clamp in which the piping system is upheld from an upperportion rather than form base. This type of pipe support is available with or without insulation.
Hot Dip Galvanizing A process of protecting metallic surfaces from corrosion or rust by dipping the materials for acertain period in boiling chemicals.
Hotshoe A type of assembly used to give necessary support to a piping system while not dissipatingelevated temperatures of the piping system at a certain point.
Inner Thrust Ring It is a plate welded to the outer arch of a pipe to restrict the sliding of the insulation assemblyagainst the pipe wall.
Inserts Insulation material usually of higher compressive strength joined to existing insulation toprovide reinforcement to a pipe support.
K-Factor Numerical representation of Thermal conductivity (See Thermal Conductivity).
Layering System A procedure of dividing insulation thickness into smaller increments of layers for totalinsulation thickness above 3.5".
Linear ExpansionCoefficient
It is the ratio of the change in length per degree temperature change to the original length(ASTM D696).
Mean Specific Heat The quantity of heat required to change the temperature by one degree of a unit mass ofsubstance, measured as the average quantity over the temperature range specified (ASTMC351).
Modulus of Elasticity It is the ratio of stress to corresponding strain below the proportional limit. Since rigid foams donot conform to Hooke's Law throughout their elastic range, a "tangent modulus of elasticity" isused - the tangent having the slope of the greatest part of the curve that follows Hooke's Law(expressed in psi).
Monolar Mastic A type of coating used to protect polyurethane surface from moisture permeation.
Pipe Support An assembly used to uphold a piping system at desired location.
Polyurethane Foam The insulation material available in a variety of densities used in cryogenic systems.
Proportional Limit The greatest stress which a material is capable of sustaining without any deviation from theproportionality of stress to strain (Hooke's Law).
Protection Shield The metallic component of piping support wrapped directly around the insulation in order tokeep the assembly intact and provide necessary protection to the insulation.
Rate of Rise Rate of Rise is the rate at which the volume of a foaming system changes under standardconditions. (ASTM D2237)
Rigid Urethane Foams These include a variety of foams having a wide range of properties. Densities range from 60lb. / ft to below 1 lb. / ft and the properties change with densities. Rigid Urethane foams have,in general, low elongation (
7/25/2019 Pre Insulated Pipe Supports Catalogue
11/206
Semi-Rigid UrethaneFoam
A term often applied to low density (
7/25/2019 Pre Insulated Pipe Supports Catalogue
12/206
Insulation Layering
At Piping Technology and Products, we recommend multiple layers for cold shoe supports that have a
total insulation thickness of four inches or greater.
In the field, cold shoes are typically mated with existing pipe insulation. Due to the low temperature of
pipe, moisture from the ambient air can be drawn into the pipe through gaps that may exist between
the coldshoe and the insulation. At lower temperatures, where thicker insulation is required, there is
greater opportunity for moisture to be drawn into the pipe. This is because of the increased single
mating surface area between the insulation and the cold shoe.
A solution that eliminates this potential problem is providing multiple mating surfaces between the line
insulation and the pipe support. Hence: When insulation thickness is four inches and greater, multiple
layers provide an improved moisture seal due to steps between the different layers.
To determine the thickness of each layer, refer to our suggested layering chart on the following page.
To use this table, reference the total insulation thickness to determine how many layers are suggested
and how thick each layer should be.
Example:A four inch (4) pipe that requires five inches of insulation: Referring to PT&Ps suggested
layering chart, two layers are required. The first layer (inner layer) thickness is suggested to be 2 2/2
and the second layer (the outer layer) is suggested to be 2 1/2 thick.
Piping Technology and Products can tailor a layering system to meet the customers requirements. The
included layering chart is only a guideline.
7/25/2019 Pre Insulated Pipe Supports Catalogue
13/206
Suggested Insulation Layering Chart
NOMINOMINOMINOMINALNALNALNAL
2.52.53822.52.57222.56.5
3.52.5632.55.5
2.52.55
2.524.5224
3.53.533
2.52.522
1.51.511
Layer 3Layer 3Layer 3Layer 3Layer 2Layer 2Layer 2Layer 2Layer 1Layer 1Layer 1Layer 1Insulation ThicknessInsulation ThicknessInsulation ThicknessInsulation Thickness
Re
sting Shoe made of Calcium Silicate for hot service
7/25/2019 Pre Insulated Pipe Supports Catalogue
14/206
POLYURETHANE TECHNICAL INFORMATION
Polyurethane foam is one of the major components of pre-insulated pipe supports manufactured at
Piping Technology & Products. Polyurethane is different from most plastic materials in that it can betailored to meet various load requirements of varying applications.
Polyurethane foams are produced by reacting an equal ratio of di- or polyisocyanurates with polyols, in
the presence of water, which acts as the blowing agent. Polyisocyanurates are formed when a higher
ratio of di- or polyisocyanate are mixed with the polyol. All rigid foams made from polyisocyanrate
systems have some form of polyurethane in them and can be called a polyurethane foam. The physical
properties differ very little at high densities. Polyisocyanurate foams are used in applications where
dimensional stability over 200 deg F is required. However, for cryogenic applications, where your
pipeline insulation is not exposed to high temperatures, PUF is an acceptable substitution.
A common method used to obtain a change in load capacity is achange in density. At Piping Technology and Products, we offer 10
lbs. / ft3, 14 lbs. / ft3, and 20 lbs. / ft3densities.
Density can be varied by changing the amount of blowing agent
(water content). The density of polyurethane decreases with
increase in water content (See Fig. 1 ). This relationship can be
shown as follow:
W = 3.706 / D1.126
Where: W = % of water contentD = Density of foam (lbs. / ft3.)
In addition to density, the strength of a rigid urethane foam is also
influenced by many factors such as catalyst, surfactant, type of
mixing, the type of foaming system: base polyol and isosyanate,
and the influence of each of these on the foam cell structure.
Rigid urethane foams generally have an elastic region in which
stress is nearly proportional to strain. They do not exactly follow
Hooke's Law (stress is proportional to strain) because the curve is
very slightly "S" shaped. Fig. 2 shows this in detail.
Polyurethane is anisotropic, or polyurethane is stronger in the
direction of foam rise. At Piping Technology and Products, the
anisotropic character or directional properties of our polyurethane is
reduced by overloading the mold used to form the polyurethane.
7/25/2019 Pre Insulated Pipe Supports Catalogue
15/206
By overloading the mold, we can control the cell structure
and provide uniform physical properties. A relationship
between compressive strength and the density of the foam is
given in Fig. 3.
Polyurethane is a thermosetting material; however, it doessoften slightly with increased temperature and hardens
somewhat at very low temperatures. Softening at high
temperatures affects the polyurethane in two ways: (a) loss
of strength properties and (b) change in foam dimensions
(particularly low density foams). Low temperatures
generally have very little effect on polyurethane properties
other than to make them a little harder and more brittle. See
Fig. 4 for these effects.
Rigid polyurethane foams have a relatively large amount of cross-linking as the foam expands.
Our suppliers of the raw chemicals control the degree of cross-linking by functionality (higherfunctionality produces more cross-links) and molecular weight of the components in the blend.
The rigid cells provide the poured foam with strength and the interior space provides low thermal
conductivity. Water is used as the blowing agent for foam in this 10 to 40 lb-density range.
The relationship between temperature, thermal conductivity and the density of polyurethane foam
is shown in Fig. 5.
The relationships of foam's density with its Elastic Modules in Compression, Tensile Strength,
Elastic Modules in Tension, and Shear Strength are given in Figs. 6 through 9 respectively.
Please see the following for the respective curves.
7/25/2019 Pre Insulated Pipe Supports Catalogue
16/206
Piping Technology & Products has a complete manufacturing facility for production of polyurethane
required for pipe supports. We invite our customers to visit our facility and observe the fabrication of
insulated pipe supports of all types.
DENSITY COMPRESSIVE
STRENGTH
FLEXURALSTRENGTH(flatwise withgrain) (psi)
TENSILESTRENGTH(with grain)
(psi)
MODULUS OFELASTICITY
(psi)
CLOSEDCELL
CONTENT(%)
TEMPERATURE(F) CONTINUOUS
OPERATIONK-FACTOR
THERMALCONDUCTIVITY(btu/hr m^2 of)
SHEAR(flatwise)(1/8 thk.)
(psi)
DENSITY(lb/in^3)
WATERABSORPTION
(%)
PUF (10 pci) 200.00 400.00 300.00 6,000.00 95.00 -300.00 0.08 0.1600 180.00 0.1157 0.22
PUF (14pci) 300.00 600.00 500.00 11,000.00 95.00 -300.00 0.12 0.2000 200.00 0.1736 0.18
PUF (20pci) 500.00 1,100.00 600.00 20,000.00 95.00 -300.00 0.14 0.2500 400.00 0.2893 0.13
7/25/2019 Pre Insulated Pipe Supports Catalogue
17/206
Laminated Beechwood Technical Information
Permali or Insulam is an insulating material used in applications which require high tensile and
compressive strength (see table below). In addition, due to its exceptional resistance to moisture, itserves as a suitable insulator where the support (LNG lines, flare lines & dummy legs) is exposed to
harsh environmental elements.
Permali or Insulam is a phenolic laminate (densified, impregnated wood) product made from
carefully selected thin beechwood veneers. These wood layers are impregnated under vaccuum
conditions with a special synthetic resin and then densified through the application of heat and
pressure. The result is a homogenous material that combines the great strength and toughness of wood
fibers with the excellent stability and dielectric properties of the most advanced thermosetting. The
phenolic laminated block material is furnished with cross-directional fibers as shown in Figure 10
below.
DENSITY COMPRESSIVE
STRENGTH
FLEXURALSTRENGTH(flatwise withgrain) (psi)
TENSILESTRENGTH(with grain)
(psi)
MODULUS OFELASTICITY
(psi)
CLOSEDCELL
CONTENT(%)
TEMPERATURE(F) CONTINUOUS
OPERATIONK-FACTOR
THERMALCONDUCTIVITY(btu/hr m^2 of)
SHEAR(flatwise)(1/8 thk.)
(psi)
DENSITY(lb/in^3)
WATERABSORPTION
(%)
PERMALI 30000.00 15000.00 15000.00 2.0 10^6 N/A 221.00 N/A 0.0018 7200.00 0.0469 0.75
7/25/2019 Pre Insulated Pipe Supports Catalogue
18/206
FOAMGLASTECHNICAL INFORMATION
Foamglas insulation is a light weight, rigid insulation composed of millions of completely sealed
glass cells. Each cell serves as an insulating agent. Foamglas is widely used in the cryogenic and hotpipe supports and is fabricated in various shapes, thickness, and sizes to meet the particular
requirements of an application.
One unique advantage that Foamglas has is its very low moisture absorption. Since Foamglas
insulation is full of closed glass cells, it resists moisture in both liquid and vapor form. This guarantees
the long term performance of the insulation. Foamglas insulation's resistance to moisture ensures
that, properly installed, it retains its original thermal efficiency.
The major advantages and applications of Foamglas insulation are listed below. For details about the
physical and mechanical properties of the Foamglas material, please refer to the table below.
Major Advantages:-
i. Constant Insulating Efficiency.
ii. Fire Protection.
iii. Corrosion Resistance.
iv. Long Term Dimensional Stability.
v. Physical Strength.
Major Applications:-
i. Cryogenic and Hot Pipe Supports.
ii. Cryogenic Tanks and Vessels.
iii. Chilled and Hot Water Service Lines.iv. Over-fit and Revitalize the Old Insulation.
v. Composite Insulation Systems for Special Conditions.
DENSITY COMPRESSIVE
STRENGTH
FLEXURALSTRENGTH(flatwise withgrain) (psi)
TENSILESTRENGTH(with grain)
(psi)
MODULUS OFELASTICITY
(psi)
CLOSEDCELL
CONTENT(%)
TEMPERATURE(F) CONTINUOUS
OPERATIONK-FACTOR
THERMALCONDUCTIVITY(btu/hr m^2 of)
SHEAR(flatwise)(1/8 thk.)
(psi)
DENSITY(lb/in^3)
WATERABSORPTION
(%)
FOAMGLAS
(8pcf) 400.00 80.00 N/A 1.3 10^6 N/A 500 max. N/A 0.7000 N/A 0.0046 0.70
7/25/2019 Pre Insulated Pipe Supports Catalogue
19/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
20/206
PT&P PRODUCT SELECTION TREE - HOTSH
Hot
Application? No
Resting Hotshoes
Without Base
HS-1000 P, 120
HS-1001 P, 122
HS-4001 P, 176
Split T-Base
Split T-Base
HS-1010 P, 124
HS-1011 P, 126
U-Type Base
U-Type Base
Double-T Base
Double-T Base
HS-1020 P, 128
HS-1021 P, 130
HS-4010 P, 178
HS-4011 P, 180HS-4020 P, 182
HS-4021 P, 184
HS-4030 P, 186
HS-4031 P, 188
HS-1030 P, 132
HS-1031 P, 134
Guided Hotshoes TM
Without Base
Pre-insulated
Hanger SupportDouble Clamp
Phenolic Support
Misc. Hotshoes
Roller Type Hanging Rolle
HS-6010 P, 190 HS-6020 P, 192 HS-6040 P, 196 HS-6050 P, 19
HS
HS
HS
HS
HS
HS-6030 P, 194
Dummy Leg
Phenolic Block
7/25/2019 Pre Insulated Pipe Supports Catalogue
21/206
Low Temperature Support Specifications
1.0 Scope
This specification covers the requirements for the design, fabrication and use of our pre-insulated low temperaturepipe supports. These supports are for pipes having surface temperature ranges of 460F (-273C) to 280F
(138C).
2.0 General Requirements
2.1 All insulated pipes shall be supported with pre-insulated pipe supports.
2.2 Insulated pipe supports shall comply with the following standards:
ANSI/ASME B31.1 & B31.3
Manufacturers Standardization Society SP-58, 69, & 89.
2.3 The following criteria shall be considered in the selection of low temperature insulated supports:
A. Vertical, lateral and axial support design load limits.B. Vertical, lateral, and axial support design travel limits.C. Temperature of the support, at the pipe surface, and ambient conditions.D. All test or pre-operational loads that may exceed normal operating conditions.E. Any dimensional clearances needed during installation and operation should be specified.F. Material for any items that will be welded directly to the pipe.G. All loading and displacements caused by seismic, hydraulic surge, or other disturbances.H. Temperature at the support steel.
2.4 Upon request by the purchaser or the end user, design calculations of supports will be made available forreview.
2.5 Upon request by the purchaser or the end user, localized stress calculations for lugs and other welded
attachments will be made available for review.
2.6 Prior to placing an order, all special requirements such as mill test reports, material certification or non-standard materials must be specified.
3.0 Design Criteria
3.1 The load bearing insulating materials used in the support shall be the same material that was used to ratethe support.
3.2 At the request of the end user or the purchaser, we will make available compressive strength and thermalconductivity testing results of the high density polyurethane in the format provided by MSS SP-89.
Testing will be done at the maximum temperature of -196C.
3.3 A description of the quantity of load that can be applied to the support shall be provided for evaluationupon request. A minimum safety factor of 5 at the system design temperature shall be used to determine
the maximum load.
3.4 Testing for compressive strength properties shall comply with ASTM D1621, the standard testing methodfor compressive properties of Rigid Cellular Plastics.
3.5 Testing for thermal conductivity shall comply with ASTM C177, Steady State Heat Flux Measurementsand Thermal Transmission Properties by means of the Guarded Hot Plate Apparatus.
7/25/2019 Pre Insulated Pipe Supports Catalogue
22/206
3.6 Load bearing element capacity shall be demonstrated at the system design temperature and load.
3.7 The insulated pipe support assembly shall exert enough clamping force to assure that the support willmove axially with the pipe and will not slip when under design conditions.
3.8 All slide plate surfaces shall be designed so that the coefficient of friction will be limited to .1 for thedesign life without requiring lubrication. Any friction reducing material that requires bonding shall be
bonded to a backing structure prior to shipment.
3.9 High density polyurethane shall have the following maximum thermal conductivity:
A. 10 lb./cu.ft. foam - .114 BTU-in/hr-ft2 F (.0164 W/m- o K)
B. 14 lb./cu.ft. foam - .12 BTU-in/hr-ft2 F (.0173 W/m- o K)
C. 20 lb./cu.ft. foam - .22 BTU-in/hr-ft2 F (.0320 W/m- o K)
3.10 CFCs shall not be used in the manufacture of high-density polyurethane foam.
4.0 Fabrication
4.1 All polyurethane foam shall be monolithic and molded oversized so that excess material shall be removedby cutting to achieve the final finished dimensions, the outer skin shall be removed.
4.2 The insulated pipe support shall:A. Come pre-assembled with sufficient insulation extending past the outer metal jacket allowing the
pipe insulator to butt the line insulation against it.
B. All exposed surfaces will be coated with mastic to protect the foam from moisture and UVdegradation. The mastic will have a minimum perm rating of .02 (ASTM E-96).
C. The vapor barrier between the metallic jacket and the insulating material will also have a perm ratingof .02.
D. The ID and OD dimensions of the insulation shall conform to ASTM specification C585 unlessotherwise specified.
4.3 Designs having sliding surfaces shall incorporate two slide plates at each surface. Each slide plate will be
made of 3/32 thick glass filled reinforced Teflonbonded to a 10GA carbon steel backing plate. The
Teflonwill be recessed 1/4 from the edge of the plate.
4.4 All welding shall comply with B31.3 and B31.1 Piping Code and AWS D1.1
4.5 The following items unless otherwise noted on contract drawings shall be in accordance with thefollowing:
A. Structure shapes and plate: ASTM A-36B. Bolts and studs: ASTM A-307C. Nuts: A563
5.0 Shipping and Handling
5.1 Each insulated support assembly shall be clearly and permanently marked with the support identificationnumber.
5.2 The support marking shall be visible prior to and after installation.
5.3 Unless otherwise specified, supports are to be shipped on pallets, wrapped in black plastic, and shrinkwrapped to prevent moisture and UV damage.
7/25/2019 Pre Insulated Pipe Supports Catalogue
23/206
5.4 A packing list will be included with each shipment.
5.5 These supports must be stored in a dry area and protected from exposure to sunlight, rain and moisture.
6.0 Extent of Work
6.1 Work Included:Furnish the insulated pipe support assembly that includes the insulation inserts, the metallic jacket, the
steel bridle, the guide clips, and any other necessary hardware which requires complete assembly.
6.2 Work Not Included:A. Providing structural steel that is not an integral part of the support.B. Receiving, unloading, and installing of support.
7.0 Quotation
7.1 Quotations shall be submitted to the Quotation Manager by fax, writing, or e-mail.
7.2 Bidder shall quote on all equipment specified in the quotation. Manufacturer shall be Piping Technologyand Products, Inc.
7.3 Bidder shall provide a unit and extended price list for each assembly. Bidder shall total all pricing on bid.
8.0 Information to be Furnished After Award but Prior to Shipping
The supplier shall furnish installation instructions necessary for the proper installation of support.
9.0 Correspondence
9.1 All correspondence, drawings, and other submittals shall bear reference to the purchase order number andproduct ID.
9.2 Correspondence concerning technical data, shipping information, changes to the purchase order orspecification not covered in the purchase order shall be sent to the Project Engineer.
9.3 Correspondence regarding purchasing shall be sent to the Quotation Manager or the Project Engineer.
10.0 Guarantees
The supplier shall guarantee that the performance and design of the equipment is in strict accordance with
specifications.
11.0 Delivery
11.1 All insulated supports are to be delivered to the project site according to the terms agreed to in the
purchase order.
11.2 Job site location is Piping Technology and Products, Inc.
7/25/2019 Pre Insulated Pipe Supports Catalogue
24/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
25/206
L=12" L=18"
Pipe Vertical Vertical 1'' 1-1/2'' 2'' 2-1/2'' 3'' 3-1/2" 4''
size Load(lbs) Load(lbs) O.D. O.D. O.D. O.D. O.D. O.D. O.D.
1/2'' 162 232 3-1/8'' 4-1/4'' 5-1/4'' 6-7/8'' 7-7/8'' 8-7/8" 9-7/8''
3/4'' 203 290 3-1/8'' 4-1/4'' 5-1/4'' 6-7/8'' 7-7/8'' 8-7/8" 9-7/8''
1'' 254 363 3-3/4'' 4-3/4'' 5-13/16'' 6-7/8'' 7-7/8'' 8-7/8" 9-7/8''
1-1/4'' 321 459 3-3/4'' 5-1/4'' 5-13/16'' 6-7/8'' 7-7/8'' 8-7/8" 9-7/8''
1-1/2'' 368 525 4-1/4'' 5-1/4'' 6-7/8'' 7-7/8'' 8-7/8'' 9-7/8" 11''
2'' 459 656 5'' 6-1/16'' 7-1/4'' 8-1/8'' 9-1/8'' 10-1/8" 11-1/4''
2-1/2'' 556 794 5-1/2'' 7-1/8'' 8-1/8'' 9-1/8'' 10-1/8'' 11-1/4" 12-1/4''
3'' 677 967 6-1/16'' 7-1/8'' 8-1/8'' 9-1/8'' 10-1/8'' 11-1/4" 12-1/4''
3-1/2'' 774 1105 7-1/8'' 8-1/8'' 9-1/8'' 10-1/8'' 11-1/4'' 12-1/4" 13-1/4''4'' 870 1243 7-1/8'' 8-1/8'' 9-1/8'' 10-1/8'' 11-1/4'' 12-1/4" 13-1/4''
5'' 1076 1537 8-1/8'' 9-1/8'' 10-1/8'' 11-1/4'' 12-1/4'' 13-1/4" 14-1/2''
6'' 1281 1831 9-15/16'' 1 0-3/8'' 11-1/2'' 12-1/2'' 13-1/2'' 14-3/4" 15-3/4''
L=12" L=18"
Pipe Vertical Vertical 1'' 1-1/2'' 2'' 2-1/2'' 3'' 3-1/2" 4''
size Load(lbs) Load(lbs) O.D. O.D. O.D. O.D. O.D. O.D. O.D.
8'' 2502 3575 11-1/2'' 12-1/2'' 13-1/2'' 14-3/4'' 15-3/4'' 16-3/4" 17-3/4''
10'' 3119 4456 13-1/2'' 14-3/4'' 15-3/4'' 16-3/4'' 17-3/4'' 18-3/4" 19-3/4''
12'' 3699 5285 14-3/4" 16-3/4'' 17-3/4'' 18-3/4'' 19-3/4'' 20-3/4" 21-3/4''
14'' 4062 5803 17'' 18'' 19'' 20'' 21'' 22" 23''
16'' 7737 11053 19'' 20'' 21'' 22'' 23'' 24" 25''
18'' 8704 12434 21'' 22'' 23'' 24'' 25'' 26" 27''
20'' 9671 13816 23'' 24'' 25'' 26'' 27'' 28" 29''
24'' 11605 16579 27'' 28'' 29'' 30'' 31'' 32" 33''
26'' 12573 17961 29-1/2'' 30-1/2'' 31-1/2'' 32-1/2'' 33-1/2'' 34-1/2" 35-1/2''
28'' 13540 19342 31-1/2'' 32-1/2'' 33-1/2'' 34-1/2'' 35-1/2'' 36-1/2" 37-1/2''
30'' 14507 20724 33-1/2'' 34-1/2'' 35-1/2'' 36-1/2'' 37-1/2'' 38-1/2" 39-1/2''
32'' 15474 22106 35-1/2'' 36-1/2'' 37-1/2'' 38-1/2'' 39-1/2'' 40-1/2" 41-1/2''
34'' 16441 23487 37-1/2'' 38-1/2'' 39-1/2'' 40-1/2'' 41-1/2'' 42-1/2" 43-1/2''
36'' 17408 24869 39-1/2'' 40-1/2'' 41-1/2'' 42-1/2'' 43-1/2'' 44-1/2" 45-1/2''
40'' 19342 27632 43-1/2'' 44-1/2'' 45-1/2'' 46-1/2'' 47-1/2'' 48-1/2" 49-1/2''
42'' 20310 29014 45-1/2'' 46-1/2'' 47-1/2'' 48-1/2'' 49-1/2'' 50-1/2" 51-1/2''
Insulation Thickness
Insulation Thickness
http://www.pipingtech.com/preis/cs1000.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
26/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
27/206
L=12" L=18"
Pipe Vertical Vertical 1'' 1-1/2'' 2'' 2-1/2'' 3'' 3-1/2" 4''
size Load(lbs) Load(lbs) O.D. O.D. O.D. O.D. O.D. O.D. O.D.
1/2'' 162 232 3-1/8'' 4-1/4'' 5-1/4'' 6-7/8'' 7 -7/8'' 8 -7/8" 9 -7/8''
3/4'' 203 290 3-1/8'' 4-1/4'' 5-1/4'' 6-7/8'' 7 -7/8'' 8 -7/8" 9 -7/8''
1'' 254 363 3-3/4'' 4-3/4'' 5-13/16'' 6-7/8'' 7 -7/8'' 8 -7/8" 9 -7/8''
1-1/4'' 321 459 3-3/4'' 5-1/4'' 5-13/16'' 6-7/8'' 7-7/8'' 8-7/8" 9-7/8''
1-1/2'' 368 525 4-1/4'' 5-1/4'' 6-7/8'' 7-7/8'' 8 -7/8'' 9 -7/8" 11''
2'' 459 656 5'' 6-1/16'' 7-1/4'' 8-1/8'' 9-1/8'' 10-1/8" 11-1/4''
2-1/2' ' 556 794 5-1/2' ' 7-1/8' ' 8-1/8' ' 9-1/8' ' 10-1/8' ' 11-1/4" 12-1/4''
3'' 677 967 6-1/16'' 7-1/8'' 8-1/8'' 9-1/8'' 10-1/8'' 11-1/4" 12-1/4''
3-1/2' ' 774 1105 7-1/8' ' 8-1/8' ' 9-1/8' ' 10-1/8'' 11-1/4' ' 12-1/4" 13-1/4''
4' ' 870 1243 7-1/8' ' 8-1/8' ' 9-1/8' ' 10-1/8'' 11-1/4' ' 12-1/4" 13-1/4''
5' ' 1076 1537 8-1/8' ' 9-1/8' ' 10-1/8'' 11-1/4'' 12-1/4' ' 13-1/4" 14-1/2''
6'' 1281 1831 9-15/16'' 10-3/8'' 11-1/2'' 12-1/2'' 13-1/2'' 14-3/4" 15-3/4''
L=12" L=18"
Pipe Vertical Vertical 1'' 1-1/2'' 2'' 2-1/2'' 3'' 3-1/2" 4''
size Load(lbs) Load(lbs) O.D. O.D. O.D. O.D. O.D. O.D. O.D.
8'' 2502 3575 11-1/2'' 12-1/2'' 13-1/2'' 14-3/4'' 15-3/4'' 16-3/4" 17-3/4''
10'' 3119 4456 13-1/2'' 14-3/4'' 15-3/4'' 16-3/4'' 17-3/4'' 18-3/4" 19-3/4''
12'' 3699 5285 14-3/4" 16-3/4'' 17-3/4'' 18-3/4'' 19-3/4'' 20-3/4" 21-3/4''
14'' 4062 5803 17'' 18'' 19'' 20'' 21'' 22" 23''
16'' 7737 11053 19'' 20'' 21'' 22'' 23'' 24" 25''
18'' 8704 12434 21'' 22'' 23'' 24'' 25'' 26" 27''20'' 9671 13816 23'' 24'' 25'' 26'' 27'' 28" 29''
24'' 11605 16579 27'' 28'' 29'' 30'' 31'' 32" 33''
26'' 12573 17961 29-1/2'' 30-1/2'' 31-1/2'' 32-1/2'' 33-1/2'' 34-1/2" 35-1/2''
28'' 13540 19342 31-1/2'' 32-1/2'' 33-1/2'' 34-1/2'' 35-1/2'' 36-1/2" 37-1/2''
30'' 14507 20724 33-1/2'' 34-1/2'' 35-1/2'' 36-1/2'' 37-1/2'' 38-1/2" 39-1/2''
32'' 15474 22106 35-1/2'' 36-1/2'' 37-1/2'' 38-1/2'' 39-1/2'' 40-1/2" 41-1/2''
34'' 16441 23487 37-1/2'' 38-1/2'' 39-1/2'' 40-1/2'' 41-1/2'' 42-1/2" 43-1/2''
36'' 17408 24869 39-1/2'' 40-1/2'' 41-1/2'' 42-1/2'' 43-1/2'' 44-1/2" 45-1/2''
40'' 19342 27632 43-1/2'' 44-1/2'' 45-1/2'' 46-1/2'' 47-1/2'' 48-1/2" 49-1/2''
42'' 20310 29014 45-1/2'' 46-1/2'' 47-1/2'' 48-1/2'' 49-1/2'' 50-1/2" 51-1/2''
Insulation Thickness
Insulation Thickness
http://www.pipingtech.com/preis/cs1001.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
28/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
29/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H
1/2'' 162 232 3" 3-1/8'' 4'' 3" 4-1/4'' 4'' 3" 5-1/4'' 4''
3/4'' 203 290 3" 3-1/8'' 4'' 3" 4-1/4'' 4'' 3" 5-1/4'' 4''
1'' 254 363 3" 3-3/4'' 4'' 3" 4-3/4'' 4'' 3" 5-13/16'' 4''
1-1/4'' 321 459 3" 3-3/4'' 4'' 3" 5-1/4'' 4'' 3" 5-13/16'' 4''
1-1/2'' 368 525 3" 4-1/4'' 4'' 3" 5-1/4'' 4'' 3" 6-7/8'' 4''
2'' 459 656 4" 5'' 4'' 4" 6-1/16'' 4'' 4" 7-1/4'' 4''
2-1/2'' 556 794 4" 5-1/2'' 4'' 4" 7-1/8'' 4'' 4" 8-1/8'' 4''
3'' 677 967 4" 6-1/16'' 4'' 4" 7-1/8'' 4'' 4" 8-1/8'' 4''
3-1/2'' 774 1105 4" 7-1/8'' 4'' 4" 8-1/8'' 4'' 4" 9-1/8'' 4''
4'' 870 1243 4" 7-1/8'' 4'' 4" 8-1/8'' 4'' 4" 9-1/8'' 4''
5'' 1076 1537 4" 8-1/8'' 4'' 4" 9-1/8'' 4'' 4" 10-1/8'' 4''
6'' 1281 1831 6" 9-15/16'' 4'' 6" 10-3/8'' 4'' 6" 11-1/2'' 4''
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H W O.D. H
1/2'' 162 232 3" 6-7/8'' 4'' 3" 7-7/8'' 6'' 3" 8-7/8" 6" 3" 9-7/8'' 6''
3/4'' 203 290 3" 6-7/8'' 4'' 3" 7-7/8'' 6'' 3" 8-7/8" 6" 3" 9-7/8'' 6''
1'' 254 363 3" 6-7/8'' 4'' 3" 7-7/8'' 6'' 3" 8-7/8" 6" 3" 9-7/8'' 6''
1-1/4'' 321 459 3" 6-7/8'' 4'' 3" 7-7/8'' 6'' 3" 8-7/8" 6" 3" 9-7/8'' 6''
1-1/2'' 368 525 3" 7-7/8'' 4'' 3" 8-7/8'' 6'' 3" 9-7/8" 6" 3" 11'' 6''
2'' 459 656 4" 8-1/8'' 4'' 4" 9-1/8'' 6'' 4" 10-1/8" 6" 4" 11-1/4'' 6''
2-1/2'' 556 794 4" 9-1/8'' 4'' 4" 10-1/8'' 6'' 4" 11-1/4" 6" 4" 12-1/4'' 6''
3'' 677 967 4" 9-1/8'' 4'' 4" 10-1/8'' 6'' 4" 11-1/4" 6" 4" 12-1/4'' 6''
3-1/2'' 774 1105 4" 10-1/8'' 4'' 4" 11-1/4'' 6'' 4" 12-1/4" 6" 4" 13-1/4'' 6''
4'' 870 1243 4" 10-1/8'' 4'' 4" 11-1/4'' 6'' 4" 12-1/4" 6" 4" 13-1/4'' 6''
5'' 1076 1537 4" 11-1/4'' 4'' 4" 12-1/4'' 6'' 4" 13-1/4" 6" 4" 14-1/2'' 6''
6'' 1281 1831 6" 12-1/2'' 4'' 6" 13-1/2'' 6'' 6" 14-3/4" 6" 6" 15-3/4'' 6''
Insulation Thickness
4''3-1/2"3''2-1/2''
1'' 1-1/2'' 2''
Insulation Thickness
http://www.pipingtech.com/preis/cs1010.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
30/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
31/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H
1/2'' 162 232 3" 3-1/8'' 4'' 3" 4-1/4'' 4'' 3" 5-1/4'' 4''
3/4'' 203 290 3" 3-1/8'' 4'' 3" 4-1/4'' 4'' 3" 5-1/4'' 4''
1'' 254 363 3" 3-3/4'' 4'' 3" 4-3/4'' 4'' 3" 5-13/16'' 4''
1-1/4'' 321 459 3" 3-3/4'' 4'' 3" 5-1/4'' 4'' 3" 5-13/16'' 4''
1-1/2'' 368 525 3" 4-1/4'' 4'' 3" 5-1/4'' 4'' 3" 6-7/8'' 4''2'' 459 656 4" 5'' 4'' 4" 6-1/16'' 4'' 4" 7-1/4'' 4''
2-1/2'' 556 794 4" 5-1/2'' 4'' 4" 7-1/8'' 4'' 4" 8-1/8'' 4''
3'' 677 967 4" 6-1/16'' 4'' 4" 7-1/8'' 4'' 4" 8-1/8'' 4''
3-1/2'' 774 1105 4" 7-1/8'' 4'' 4" 8-1/8'' 4'' 4" 9-1/8'' 4''
4'' 870 1243 4" 7-1/8'' 4'' 4" 8-1/8'' 4'' 4" 9-1/8'' 4''
5'' 1076 1537 4" 8-1/8'' 4'' 4" 9-1/8'' 4'' 4" 10-1/8'' 4''
6'' 1281 1831 6" 9-15/16'' 4'' 6" 10-3/8'' 4 '' 6" 11-1/2'' 4''
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H W O.D. H
1/2'' 162 232 3" 6-7/8'' 4'' 3" 7-7/8'' 6'' 3" 8-7/8" 6" 3" 9-7/8'' 6''
3/4'' 203 290 3" 6-7/8'' 4'' 3" 7-7/8'' 6'' 3" 8-7/8" 6" 3" 9-7/8'' 6''
1'' 254 363 3" 6-7/8'' 4'' 3" 7-7/8'' 6'' 3" 8-7/8" 6" 3" 9-7/8'' 6''
1-1/4'' 321 459 3" 6-7/8'' 4'' 3" 7-7/8'' 6'' 3" 8-7/8" 6" 3" 9-7/8'' 6''
1-1/2'' 368 525 3" 7-7/8'' 4'' 3" 8-7/8'' 6'' 3" 9-7/8" 6" 3" 11'' 6''
2'' 459 656 4" 8-1/8'' 4'' 4" 9-1/8'' 6'' 4" 10-1/8" 6" 4" 11-1/4'' 6''
2-1/2'' 556 794 4" 9-1/8'' 4'' 4" 10-1/8'' 6'' 4" 11-1/4" 6" 4" 12-1/4'' 6 ''
3'' 677 967 4" 9-1/8'' 4'' 4" 10-1/8'' 6'' 4" 11-1/4" 6" 4" 12-1/4'' 6''
3-1/2'' 774 1105 4" 10-1/8'' 4'' 4" 11-1/4'' 6'' 4" 12-1/4" 6" 4" 13-1/4'' 6''
4'' 870 1243 4" 10-1/8'' 4'' 4" 11-1/4'' 6'' 4" 12-1/4" 6" 4" 13-1/4'' 6''
5'' 1076 1537 4" 11-1/4'' 4'' 4" 12-1/4'' 6'' 4" 13-1/4" 6" 4" 14-1/2'' 6''
6'' 1281 1831 6" 12-1/2'' 4'' 6" 13-1/2'' 6'' 6" 14-3/4" 6" 6" 15-3/4'' 6''
4''3-1/2"3''2-1/2''
Insulation Thickness
Insulation Thickness
1'' 1-1/2'' 2''
http://www.pipingtech.com/preis/cs1011.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
32/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
33/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H
8'' 2502 3575 6-1/2" 11-1/2'' 4'' 7" 12-1/2'' 4'' 7-1/2" 13-1/2'' 4''
10'' 3119 4456 7-1/2" 13-1/2'' 4'' 8-1/8" 14-3/4'' 4'' 8-5/8" 15-3/4'' 4''
12'' 3699 5285 8-1/2" 14-3/4" 4'' 9-1/8" 16-3/4'' 4'' 9-5/8" 17-3/4'' 4''
14'' 4062 5803 9-1/2" 17'' 4'' 10" 18'' 4'' 10-1/2" 19'' 4''
16'' 7737 11053 10-1/2" 19'' 4'' 11" 20'' 4'' 11-1/2" 21'' 4''
18'' 8704 12434 11-1/2" 21'' 4'' 12" 22'' 4'' 12-1/2" 23'' 4''
20'' 9671 13816 12-1/2" 23'' 4'' 13" 24'' 4'' 13-1/2" 25'' 4''
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H W O.D. H
8'' 2502 3575 8-1/8" 14-3/4'' 4" 8-5/8" 15-3/4'' 6'' 9-1/8" 16-3/4" 6" 9-5/8" 17-3/4'' 6''
10'' 3119 4456 9-1/8" 16-3/4'' 4" 9-5/8" 17-3/4'' 6'' 10-1/8" 18-3/4" 6'' 10-5/8" 19-3/4'' 6''
12'' 3699 5285 10-1/8" 18-3/4'' 4" 10-5/8" 19-3/4'' 6'' 11-1/8" 20-3/4" 6'' 11-5/8" 21-3/4'' 6''14'' 4062 5803 11" 20'' 4" 11-1/2" 21'' 6'' 12" 22" 6'' 12-1/2" 23'' 6''
16'' 7737 11053 12" 22'' 6'' 12-1/2" 23'' 6'' 13" 24" 6'' 13-1/2" 25'' 6''
18'' 8704 12434 13" 24'' 6'' 13-1/2" 25'' 6'' 14" 26" 6'' 14-1/2" 27'' 6''
20'' 9671 13816 14" 26'' 6'' 14-1/2" 27'' 6'' 15" 28" 6'' 15-1/2" 29'' 6''
2-1/2'' 3'' 3-1/2" 4''
Insulation Thickness
Insulation Thickness
1'' 1-1/2'' 2''
http://www.pipingtech.com/preis/cs1020.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
34/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
35/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H8'' 2502 3575 6-1/2" 11-1/2'' 4'' 7" 12-1/2'' 4'' 7-1/2" 13-1/2'' 4''
10'' 3119 4456 7-1/2" 13-1/2'' 4'' 8-1/8" 14-3/4'' 4'' 8-5/8" 15-3/4'' 4''
12'' 3699 5285 8-1/2" 14-3/4" 4'' 9-1/8" 16-3/4'' 4'' 9-5/8" 17-3/4'' 4''
14'' 4062 5803 9-1/2" 17'' 4'' 10" 18'' 4'' 10-1/2" 19'' 4''
16'' 7737 11053 10-1/2" 19'' 4'' 11" 20'' 4'' 11-1/2" 21'' 4''
18'' 8704 12434 11-1/2" 21'' 4'' 12" 22'' 4'' 12-1/2" 23'' 4''
20'' 9671 13816 12-1/2" 23'' 4'' 13" 24'' 4'' 13-1/2" 25'' 4''
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H W O.D. H
8'' 2502 3575 8-1/8" 14-3/4'' 4" 8-5/8" 15-3/4'' 6'' 9-1/8" 16-3/4" 6" 9-5/8" 17-3/4'' 6''
10'' 3119 4456 9-1/8" 16-3/4'' 4" 9-5/8" 17-3/4'' 6'' 10-1/8" 18-3/4" 6'' 10-5/8" 19-3/4'' 6''
12'' 3699 5285 10-1/8" 18-3/4'' 4" 10-5/8" 19-3/4'' 6'' 11-1/8" 20-3/4" 6'' 11-5/8" 21-3/4'' 6''
14'' 4062 5803 11" 20'' 4" 11-1/2" 21'' 6'' 12" 22" 6'' 12-1/2" 23'' 6''
16'' 7737 11053 12" 22'' 6'' 12-1/2" 23'' 6'' 13" 24" 6'' 13-1/2" 25'' 6''
18'' 8704 12434 13" 24'' 6'' 13-1/2" 25'' 6'' 14" 26" 6'' 14-1/2" 27'' 6''
20'' 9671 13816 14" 26'' 6'' 14-1/2" 27'' 6'' 15" 28" 6'' 15-1/2" 29'' 6''
Insulation Thickness
2-1/2'' 3'' 3-1/2" 4''
Insulation Thickness
1'' 1-1/2'' 2''
http://www.pipingtech.com/preis/cs1021.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
36/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
37/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H
24'' 11605 16579 14-1/2" 27'' 4'' 15" 28'' 4'' 15-1/2" 29'' 4"
26'' 12573 17961 16-1/4" 29-1/2'' 4'' 16-3/4" 30-1/2'' 4'' 17-1/4" 31-1/2'' 4"
28'' 13540 19342 17-1/4" 31-1/2'' 4'' 17-3/4" 32-1/2'' 4'' 18-1/4" 33-1/2'' 4"30'' 14507 20724 18-1/4" 33-1/2'' 4'' 18-3/4" 34-1/2'' 4'' 19-1/4" 35-1/2'' 4"
32'' 15474 22106 19-1/4" 35-1/2'' 4'' 19-3/4" 36-1/2'' 4'' 20-1/4" 37-1/2'' 4"
34'' 16441 23487 20-1/4" 37-1/2'' 4'' 20-3/4" 38-1/2'' 4'' 21-1/4" 39-1/2'' 4"
36'' 17408 24869 21-1/4" 39-1/2'' 4'' 21-3/4" 40-1/2'' 4'' 22-1/4" 41-1/2'' 4"
40'' 19342 27632 23-1/4" 43-1/2'' 4'' 23-3/4" 44-1/2'' 4'' 24-1/4" 45-1/2'' 4"
42'' 20310 29014 24-1/4" 45-1/2'' 4'' 24-3/4" 46-1/2'' 4'' 25-1/4" 47-1/2'' 4"
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H W O.D. H
24'' 11605 16579 16" 30'' 6'' 16-1/2" 31'' 6'' 17" 32" 6" 17-1/2" 33'' 6"26'' 12573 17961 17-3/4" 32-1/2'' 6'' 18-1/4" 33-1/2'' 6'' 18-3/4" 34-1/2" 6'' 19-1/4" 35-1/2'' 6"
28'' 13540 19342 18-3/4" 34-1/2'' 6'' 19-1/4" 35-1/2'' 6'' 19-3/4" 36-1/2" 6'' 20-1/4" 37-1/2'' 6"
30'' 14507 20724 19-3/4" 36-1/2'' 6'' 20-1/4" 37-1/2'' 6'' 20-3/4" 38-1/2" 6'' 21-1/4" 39-1/2'' 6"
32'' 15474 22106 20-3/4" 38-1/2'' 6'' 21-1/4" 39-1/2'' 6'' 21-3/4" 40-1/2" 6'' 22-1/4" 41-1/2'' 6"
34'' 16441 23487 21-3/4" 40-1/2'' 6'' 22-1/4" 41-1/2'' 6'' 22-3/4" 42-1/2" 6'' 23-1/4" 43-1/2'' 6"
36'' 17408 24869 22-3/4" 42-1/2'' 6'' 23-1/4" 43-1/2'' 6'' 23-3/4" 44-1/2" 6'' 24-1/4" 45-1/2'' 6"
40'' 19342 27632 24-3/4" 46-1/2'' 6'' 25-1/4" 47-1/2'' 6'' 25-3/4" 48-1/2" 6'' 26-1/4" 49-1/2'' 6"
42'' 20310 29014 25-3/4" 48-1/2'' 6'' 26-1/4" 49-1/2'' 6'' 26-3/4" 50-1/2" 6" 27-1/4" 51-1/2'' 6"
4''
1'' 1-1/2'' 2''
Insulation Thickness
Insulation Thickness
2-1/2'' 3'' 3-1/2"
http://www.pipingtech.com/preis/cs1030.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
38/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
39/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H
24'' 11605 16579 14-1/2" 27'' 4'' 15" 28'' 4'' 15-1/2" 29'' 4"
26'' 12573 17961 16-1/4" 29-1/2'' 4'' 16-3/4" 30-1/2'' 4'' 17-1/4" 31-1/2'' 4"28'' 13540 19342 17-1/4" 31-1/2'' 4'' 17-3/4" 32-1/2'' 4'' 18-1/4" 33-1/2'' 4"
30'' 14507 20724 18-1/4" 33-1/2'' 4'' 18-3/4" 34-1/2'' 4'' 19-1/4" 35-1/2'' 4"
32'' 15474 22106 19-1/4" 35-1/2'' 4'' 19-3/4" 36-1/2'' 4'' 20-1/4" 37-1/2'' 4"
34'' 16441 23487 20-1/4" 37-1/2'' 4'' 20-3/4" 38-1/2'' 4'' 21-1/4" 39-1/2'' 4"
36'' 17408 24869 21-1/4" 39-1/2'' 4'' 21-3/4" 40-1/2'' 4'' 22-1/4" 41-1/2'' 4"
40'' 19342 27632 23-1/4" 43-1/2'' 4'' 23-3/4" 44-1/2'' 4'' 24-1/4" 45-1/2'' 4"
42'' 20310 29014 24-1/4" 45-1/2'' 4'' 24-3/4" 46-1/2'' 4'' 25-1/4" 47-1/2'' 4"
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs) W O.D. H W O.D. H W O.D. H W O.D. H
24'' 11605 16579 16" 30'' 6'' 16-1/2" 31'' 6'' 17" 32" 6" 17-1/2" 33'' 6"
26'' 12573 17961 17-3/4" 32-1/2'' 6'' 18-1/4" 33-1/2'' 6'' 18-3/4" 34-1/2" 6'' 19-1/4" 35-1/2'' 6"
28'' 13540 19342 18-3/4" 34-1/2'' 6'' 19-1/4" 35-1/2'' 6'' 19-3/4" 36-1/2" 6'' 20-1/4" 37-1/2'' 6"
30'' 14507 20724 19-3/4" 36-1/2'' 6'' 20-1/4" 37-1/2'' 6'' 20-3/4" 38-1/2" 6'' 21-1/4" 39-1/2'' 6"
32'' 15474 22106 20-3/4" 38-1/2'' 6'' 21-1/4" 39-1/2'' 6'' 21-3/4" 40-1/2" 6'' 22-1/4" 41-1/2'' 6"
34'' 16441 23487 21-3/4" 40-1/2'' 6'' 22-1/4" 41-1/2'' 6'' 22-3/4" 42-1/2" 6'' 23-1/4" 43-1/2'' 6"
36'' 17408 24869 22-3/4" 42-1/2'' 6'' 23-1/4" 43-1/2'' 6'' 23-3/4" 44-1/2" 6'' 24-1/4" 45-1/2'' 6"
40'' 19342 27632 24-3/4" 46-1/2'' 6'' 25-1/4" 47-1/2'' 6'' 25-3/4" 48-1/2" 6'' 26-1/4" 49-1/2'' 6"
42'' 20310 29014 25-3/4" 48-1/2'' 6'' 26-1/4" 49-1/2'' 6'' 26-3/4" 50-1/2" 6" 27-1/4" 51-1/2'' 6"
Insulation Thickness
2-1/2'' 3'' 3-1/2" 4''
Insulation Thickness
1'' 1-1/2'' 2''
http://www.pipingtech.com/preis/cs1031.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
40/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
41/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
1/2'' 162 232 3'' 169 3-1/8'' 4'' 4'' 169 4-1/4'' 4'' 4'' 169 5-1/4'' 4'' 4'' 169 6-7/8'' 4''
3/4'' 203 290 3'' 211 3-1/8'' 4'' 4'' 211 4-1/4'' 4'' 4'' 211 5-1/4'' 4'' 4'' 211 6-7/8'' 4''
1'' 254 363 4'' 265 3-3/4'' 4'' 4'' 265 4-3/4'' 4'' 4'' 265 5-13/16'' 4'' 4'' 265 6-7/8'' 4''1-1/4'' 321 459 4'' 334 3-3/4'' 4'' 5'' 334 5-1/4'' 4'' 4'' 334 5-13/16'' 4'' 4'' 334 6-7/8'' 4''
1-1/2'' 368 525 4'' 383 4-1/4'' 4'' 4'' 383 5-1/4'' 4'' 4'' 383 6-7/8'' 4'' 4'' 383 7-7/8'' 4''
2'' 459 656 4'' 478 5'' 4'' 4'' 478 6-1/16'' 4'' 4'' 478 7-1/4'' 4'' 4'' 478 8-1/8'' 4''
2-1/2'' 556 794 4'' 579 5-1/2'' 4'' 4'' 579 7-1/8'' 4'' 4'' 579 8-1/8'' 4'' 4'' 579 9-1/8'' 4''
3'' 677 967 4'' 705 6-1/16'' 4'' 4'' 705 7-1/8'' 4'' 4'' 705 8-1/8'' 4'' 4'' 705 9-1/8'' 4''
3-1/2'' 774 1105 4'' 806 7-1/8'' 4'' 4'' 806 8-1/8'' 4'' 4'' 806 9-1/8'' 4'' 4'' 806 10-1/8'' 4''
4'' 870 1243 4'' 907 7-1/8'' 4'' 4'' 907 8-1/8'' 4'' 4'' 907 9-1/8'' 4'' 4'' 907 10-1/8'' 4''
5'' 1076 1537 4'' 1121 8-1/8'' 4'' 4'' 1121 9-1/8'' 4'' 4'' 1121 10-1/8'' 4'' 4'' 1121 11-1/4'' 4''
6'' 1281 1831 4'' 1335 9-15/16'' 4'' 4'' 1335 10-3/8'' 4'' 4'' 1335 11-1/2'' 4'' 4'' 1335 12-1/2'' 4''
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
1/2'' 162 232 4'' 169 7-7/8'' 6'' 4'' 169 8-7/8" 6" 4'' 169 9-7/8'' 6''
3/4'' 203 290 4'' 211 7-7/8'' 6'' 4'' 211 8-7/8" 6" 4'' 211 9-7/8'' 6''
1'' 254 363 4'' 265 7-7/8'' 6'' 4'' 265 8-7/8" 6" 4'' 265 9-7/8'' 6''
1-1/4'' 321 459 4'' 334 7-7/8'' 6'' 4'' 334 8-7/8" 6" 4'' 334 9-7/8'' 6''
1-1/2'' 368 525 4'' 383 8-7/8'' 6'' 4'' 383 9-7/8" 6" 4'' 383 11'' 6''
2'' 459 656 4'' 478 9-1/8'' 6'' 4'' 478 10-1/8" 6" 4'' 478 11-1/4'' 6''
2-1/2'' 556 794 4'' 579 10-1/8'' 6'' 4'' 579 11-1/4" 6" 4'' 579 12-1/4'' 6''
3'' 677 967 4'' 705 10-1/8'' 6'' 4'' 705 11-1/4" 6" 4'' 705 12-1/4'' 6''
3-1/2'' 774 1105 4'' 806 1 1-1/4'' 6'' 4'' 806 12-1/4" 6" 4'' 806 1 3-1/4'' 6''
4'' 870 1243 4'' 907 11-1/4'' 6'' 4'' 907 12-1/4" 6" 4'' 907 13-1/4'' 6''
5'' 1076 1537 4'' 1121 12-1/4'' 6'' 4'' 1121 13-1/4" 6" 4'' 1121 14-1/2'' 6''
6'' 1281 1831 4'' 1335 13-1/2'' 6'' 4'' 1335 14-3/4" 6" 4'' 1335 15-3/4'' 6''
Insulation Thickness
3" 3-1/2" 4"
Insulation Thickness
1'' 1-1/2" 2'' 2-1/2"
http://www.pipingtech.com/preis/cs2010.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
42/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
43/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
1/2'' 162 232 3'' 169 3-1/8'' 4'' 4'' 169 4-1/4'' 4'' 4'' 169 5-1/4'' 4'' 4'' 169 6-7/8'' 4''
3/4'' 203 290 3'' 211 3-1/8'' 4'' 4'' 211 4-1/4'' 4'' 4'' 211 5-1/4'' 4'' 4'' 211 6-7/8'' 4''
1'' 254 363 4'' 265 3-3/4'' 4'' 4'' 265 4-3/4'' 4'' 4'' 265 5-13/16'' 4'' 4'' 265 6-7/8'' 4''
1-1/4'' 321 459 4'' 334 3-3/4'' 4'' 5'' 334 5-1/4'' 4'' 4'' 334 5-13/16'' 4'' 4'' 334 6-7/8'' 4''
1-1/2'' 368 525 4'' 383 4-1/4'' 4'' 4'' 383 5-1/4'' 4'' 4'' 383 6-7/8'' 4'' 4'' 383 7-7/8'' 4''2'' 459 656 4'' 478 5'' 4'' 4'' 478 6-1/16'' 4'' 4'' 478 7-1/4'' 4'' 4'' 478 8-1/8'' 4''
2-1/2'' 556 794 4'' 579 5-1/2'' 4'' 4'' 579 7-1/8'' 4'' 4'' 579 8-1/8'' 4'' 4'' 579 9-1/8'' 4''
3'' 677 967 4'' 705 6-1/16'' 4'' 4'' 705 7-1/8'' 4'' 4'' 705 8-1/8'' 4'' 4'' 705 9-1/8'' 4''
3-1/2'' 774 1105 4'' 806 7-1/8'' 4'' 4'' 806 8-1/8'' 4'' 4'' 806 9-1/8'' 4'' 4'' 806 10-1/8'' 4''
4'' 870 1243 4'' 907 7-1/8'' 4'' 4'' 907 8-1/8'' 4'' 4'' 907 9-1/8'' 4'' 4'' 907 10-1/8'' 4 ''
5'' 1076 1537 4'' 1121 8-1/8'' 4'' 4'' 1121 9-1/8'' 4'' 4'' 1121 10-1/8'' 4'' 4'' 1121 11-1/4'' 4''
6'' 1281 1831 4'' 1335 9-15/16'' 4'' 4'' 1335 10-3/8'' 4'' 4'' 1335 11-1/2'' 4'' 4'' 1335 12-1/2'' 4''
L=12" L=18"
Pipe Vert ical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
1/2'' 162 232 4'' 169 7-7/8'' 6'' 4'' 169 8-7/8" 6" 4'' 169 9-7/8'' 6''
3/4'' 203 290 4'' 211 7-7/8'' 6'' 4'' 211 8-7/8" 6" 4'' 211 9-7/8'' 6''
1'' 254 363 4'' 265 7-7/8'' 6'' 4'' 265 8-7/8" 6" 4'' 265 9-7/8'' 6''
1-1/4'' 321 459 4'' 334 7-7/8'' 6'' 4'' 334 8-7/8" 6" 4'' 334 9-7/8'' 6''
1-1/2'' 368 525 4'' 383 8-7/8'' 6'' 4'' 383 9-7/8" 6" 4'' 383 11'' 6''
2'' 459 656 4'' 478 9-1/8'' 6'' 4'' 478 10-1/8" 6" 4'' 478 11-1/4'' 6''
2-1/2'' 556 794 4'' 579 10-1/8'' 6'' 4'' 579 11-1/4" 6" 4'' 579 12-1/4'' 6''
3'' 677 967 4'' 705 10-1/8'' 6'' 4'' 705 11-1/4" 6" 4'' 705 12-1/4'' 6''
3-1/2'' 774 1105 4'' 806 11-1/4'' 6'' 4'' 806 12-1/4" 6" 4'' 806 13-1/4'' 6''
4'' 870 1243 4'' 907 11-1/4'' 6'' 4'' 907 12-1/4" 6" 4'' 907 13-1/4'' 6''
5'' 1076 1537 4'' 1121 12-1/4'' 6'' 4'' 1121 13-1/4" 6" 4'' 1121 14-1/2'' 6''
6'' 1281 1831 4'' 1335 13-1/2'' 6'' 4'' 1335 14-3/4" 6" 4'' 1335 15-3/4'' 6''
3" 3-1/2" 4"
Insulation Thickness
Insulation Thickness
1'' 1-1/2" 2'' 2-1/2"
http://www.pipingtech.com/preis/cs2011.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
44/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
45/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
1/2'' 162 232 3'' 169 3-1/8'' 4'' 4'' 169 4-1/4'' 4'' 4'' 169 5-1/4'' 4'' 4'' 169 6-7/8'' 4''
3/4'' 203 290 3'' 211 3-1/8'' 4'' 4'' 211 4-1/4'' 4'' 4'' 211 5-1/4'' 4'' 4'' 211 6-7/8'' 4''
1'' 254 363 4'' 265 3-3/4'' 4'' 4'' 265 4-3/4'' 4'' 4'' 265 5-13/16'' 4 '' 4'' 265 6-7/8'' 4''
1-1/4'' 321 459 4'' 334 3-3/4'' 4'' 5'' 334 5-1/4'' 4'' 4'' 334 5-13/16'' 4'' 4'' 334 6 -7/8'' 4''
1-1/2'' 368 525 4'' 383 4-1/4'' 4'' 4'' 383 5-1/4'' 4'' 4'' 383 6-7/8'' 4'' 4'' 383 7-7/8'' 4''2'' 459 656 4'' 478 5'' 4'' 4'' 478 6-1/16'' 4'' 4'' 478 7-1/4'' 4'' 4'' 478 8-1/8'' 4''
2-1/2'' 556 794 4'' 579 5-1/2'' 4'' 4'' 579 7-1/8'' 4'' 4'' 579 8-1/8'' 4'' 4'' 579 9-1/8'' 4''
3'' 677 967 4'' 705 6-1/16'' 4'' 4'' 705 7-1/8'' 4'' 4'' 705 8-1/8'' 4'' 4'' 705 9-1/8'' 4''
3-1/2'' 774 1105 4'' 806 7-1/8'' 4'' 4'' 806 8 -1/8'' 4'' 4'' 806 9-1/8'' 4'' 4'' 806 10-1/8'' 4''
4'' 870 1243 4'' 907 7-1/8'' 4'' 4'' 907 8-1/8'' 4'' 4'' 907 9-1/8'' 4'' 4'' 907 10-1/8'' 4''
5'' 1076 1537 4'' 1121 8-1/8'' 4'' 4'' 1121 9-1/8'' 4'' 4'' 1121 10-1/8'' 4'' 4'' 1121 11-1/4'' 4''
6'' 1281 1831 4'' 1335 9-15/16'' 4'' 4'' 1335 10-3/8'' 4'' 4'' 1335 11-1/2'' 4'' 4'' 1335 12-1/2'' 4''
L=12" L=18"
Pipe Vert ical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
1/2'' 162 232 4'' 169 7-7/8'' 6'' 4'' 169 8-7/8" 6" 4'' 169 9-7/8'' 6''
3/4'' 203 290 4'' 211 7-7/8'' 6'' 4'' 211 8-7/8" 6" 4'' 211 9-7/8'' 6''
1'' 254 363 4'' 265 7-7/8'' 6'' 4'' 265 8-7/8" 6" 4'' 265 9-7/8'' 6''1-1/4'' 321 459 4'' 334 7-7/8'' 6'' 4'' 334 8-7/8" 6" 4'' 334 9-7/8'' 6''
1-1/2'' 368 525 4'' 383 8-7/8'' 6'' 4'' 383 9-7/8" 6" 4'' 383 11'' 6''
2'' 459 656 4'' 478 9-1/8'' 6'' 4'' 478 10-1/8" 6" 4'' 478 11-1/4'' 6''
2-1/2'' 556 794 4'' 579 10-1/8'' 6'' 4'' 579 11-1/4" 6" 4'' 579 12-1/4'' 6''
3'' 677 967 4'' 705 10-1/8'' 6'' 4'' 705 11-1/4" 6" 4'' 705 12-1/4'' 6''
3-1/2'' 774 1105 4'' 806 11-1/4'' 6'' 4'' 806 12-1/4" 6" 4'' 806 13-1/4'' 6''
4'' 870 1243 4'' 907 11-1/4'' 6'' 4'' 907 12-1/4" 6" 4'' 907 13-1/4'' 6''
5'' 1076 1537 4'' 1121 12-1/4'' 6'' 4'' 1121 13-1/4" 6" 4'' 1121 14-1/2'' 6''
6'' 1281 1831 4'' 1335 13-1/2'' 6'' 4'' 1335 14-3/4" 6" 4'' 1335 15-3/4'' 6''
Insulation Thickness
1'' 1-1/2" 2'' 2-1/2"
4"3-1/2"3"
Insulation Thickness
http://www.pipingtech.com/preis/cs2012.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
46/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
47/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
8'' 2502 3575 6-1/2" 1512 11-1/2'' 4'' 7" 1806 12-1/2'' 4'' 7-1/2" 1963 13-1/2'' 4'' 8-1/8" 2564 14-3/4'' 6''10'' 3119 4456 7-1/2" 3190 13-1/2'' 4'' 8-1/8" 3847 14-3/4'' 4'' 8-5/8" 4416 15-3/4'' 4'' 9-1/8" 5024 16-3/4'' 6''
12' ' 3699 5285 8-1/2" 4416 14-3/4" 4' ' 9-1/8" 5024 16-3/4' ' 4 '' 9-5/8" 5672 17-3/4' ' 4 '' 10-1/8" 6359 18-3/4' ' 6 ''
14'' 4062 5803 9-1/2" 5024 17'' 4'' 10" 5672 18'' 4'' 10-1/2" 6359 19'' 4'' 11" 7085 20'' 6''
16'' 7737 11053 10-1/2" 10598 19'' 4'' 11" 11808 20'' 4'' 11-1/2" 13083 21'' 6'' 12" 14424 22'' 6''
18'' 8704 12434 11-1/2" 13083 21'' 4'' 12" 14424 22'' 4'' 12-1/2" 15831 23'' 6'' 13" 17303 24'' 6''
20'' 9671 13816 12-1/2" 15831 23'' 4'' 13" 17303 24'' 4'' 13-1/2" 18840 25'' 6'' 14" 20443 26'' 6''
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
8'' 2502 3575 8-5/8" 2944 15-3/4'' 6'' 9-1/8" 3349 16-3/4" 6" 9-5/8" 3781 17-3/4'' 6''
10'' 3119 4456 9-5/8" 5672 17-3/4'' 6'' 10-1/8" 6359 18-3/4" 6" 10-5/8" 7085 19-3/4'' 6''12' ' 3699 5285 10-5/8" 7085 19-3/4'' 6' ' 11-1/8" 7850 20-3/4" 6" 11-5/8" 8655 21-3/4' ' 6 ''
14'' 4062 5803 11-1/2" 7850 21'' 6'' 12" 8655 22" 6" 12-1/2" 9499 23'' 6''
16'' 7737 11053 12-1/2" 15831 23'' 6'' 13" 17303 24" 6" 13-1/2" 18840 25'' 8''
18'' 8704 12434 13-1/2" 18840 25'' 6'' 14" 20443 26" 6" 14-1/2" 22111 27'' 8''
20'' 9671 13816 14-1/2" 22111 27'' 6'' 15" 23844 28" 6" 15-1/2" 25643 29'' 8''
Insulation Thickness
1'' 1-1/2" 2'' 2-1/2"
4"3-1/2"3"
Insulation Thickness
http://www.pipingtech.com/preis/cs2020.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
48/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
49/206
L=12" L=18"
Pipe Vertical Vertical size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
8'' 2502 3575 6-1/2" 1512 11-1/2'' 4'' 7" 1806 12-1/2'' 4'' 7-1/2" 1963 13-1/2'' 4'' 8-1/8" 2564 14-3/4'' 6''
10'' 3119 4456 7-1/2" 3190 13-1/2'' 4'' 8-1/8" 3847 14-3/4'' 4'' 8-5/8" 4416 15-3/4'' 4'' 9-1/8" 5024 16-3/4'' 6''
12'' 3699 5285 8-1/2" 4416 14-3/4" 4'' 9-1/8" 5024 16-3/4' ' 4 '' 9-5/8" 5672 17-3/4' ' 4 '' 10-1/8" 6359 18-3/4' ' 6' '
14'' 4062 5803 9-1/2" 5024 17'' 4'' 10" 5672 18'' 4'' 10-1/2" 6359 19'' 4'' 11" 7085 20'' 6''
16'' 7737 11053 10-1/2" 10598 19'' 4'' 11" 11808 20'' 4'' 11-1/2" 13083 21'' 6'' 12" 14424 22'' 6''
18'' 8704 12434 11-1/2" 13083 21'' 4'' 12" 14424 22'' 4'' 12-1/2" 15831 23'' 6'' 13" 17303 24'' 6''
20'' 9671 13816 12-1/2" 15831 23'' 4'' 13" 17303 24'' 4'' 13-1/2" 18840 25'' 6'' 14" 20443 26'' 6''
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load(lbs.) O.D. H W
Axial
load(lbs.) O.D. H W
Axial
load(lbs.) O.D. H
8'' 2502 3575 8-5/8" 2944 15-3/4'' 6'' 9-1/8" 3349 16-3/4" 6" 9-5/8" 3781 17-3/4'' 6''
10'' 3119 4456 9-5/8" 5672 17-3/4'' 6'' 10-1/8" 6359 18-3/4" 6" 10-5/8" 7085 19-3/4'' 6''
12'' 3699 5285 10-5/8" 7085 19-3/4' ' 6 '' 11-1/8" 7850 20-3/4" 6" 11-5/8" 8655 21-3/4' ' 6 ''
14'' 4062 5803 11-1/2" 7850 21'' 6'' 12" 8655 22" 6" 12-1/2" 9499 23'' 6''
16'' 7737 11053 12-1/2" 15831 23'' 6'' 13" 17303 24" 6" 13-1/2" 18840 25'' 8''
18'' 8704 12434 13-1/2" 18840 25'' 6'' 14" 20443 26" 6" 14-1/2" 22111 27'' 8''
20'' 9671 13816 14-1/2" 22111 27'' 6'' 15" 23844 28" 6" 15-1/2" 25643 29'' 8''
Insulation Thickness
1'' 1-1/2" 2'' 2-1/2"
4"3-1/2"3"
Insulation Thickness
http://www.pipingtech.com/preis/cs2021.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
50/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
51/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
8'' 2502 3575 6-1/2" 1512 11-1/2'' 4'' 7" 1806 12-1/2'' 4'' 7-1/2" 1963 13-1/2'' 4'' 8-1/8" 2564 14-3/4'' 6''
10'' 3119 4456 7-1/2" 3190 13-1/2'' 4'' 8-1/8" 3847 14-3/4'' 4'' 8-5/8" 4416 15-3/4'' 4'' 9-1/8" 5024 16-3/4'' 6''
12'' 3699 5285 8-1/2" 4416 14-3/4" 4'' 9-1/8" 5024 16-3/4' ' 4 '' 9-5/8" 5672 17-3/4' ' 4 '' 10-1/8" 6359 18-3/4'' 6' '
14'' 4062 5803 9-1/2" 5024 17'' 4'' 10" 5672 18'' 4'' 10-1/2" 6359 19'' 4'' 11" 7085 20'' 6''16'' 7737 11053 10-1/2" 10598 19'' 4'' 11" 11808 20'' 4'' 11-1/2" 13083 21'' 6'' 12" 14424 22'' 6''
18'' 8704 12434 11-1/2" 13083 21'' 4'' 12" 14424 22'' 4'' 12-1/2" 15831 23'' 6'' 13" 17303 24'' 6''
20'' 9671 13816 12-1/2" 15831 23'' 4'' 13" 17303 24'' 4'' 13-1/2" 18840 25'' 6'' 14" 20443 26'' 6''
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
8'' 2502 3575 8-5/8" 2944 15-3/4'' 6'' 9-1/8" 3349 16-3/4" 6" 9-5/8" 3781 17-3/4'' 6''
10'' 3119 4456 9-5/8" 5672 17-3/4'' 6'' 10-1/8" 6359 18-3/4" 6" 10-5/8" 7085 19-3/4'' 6''
12'' 3699 5285 10-5/8" 7085 19-3/4'' 6 '' 11-1/8" 7850 20-3/4" 6" 11-5/8" 8655 21-3/4' ' 6 ''
14'' 4062 5803 11-1/2" 7850 21'' 6'' 12" 8655 22" 6" 12-1/2" 9499 23'' 6''16'' 7737 11053 12-1/2" 15831 23'' 6'' 13" 17303 24" 6" 13-1/2" 18840 25'' 8''
18'' 8704 12434 13-1/2" 18840 25'' 6'' 14" 20443 26" 6" 14-1/2" 22111 27'' 8''
20'' 9671 13816 14-1/2" 22111 27'' 6'' 15" 23844 28" 6" 15-1/2" 25643 29'' 8''
4"3-1/2"3"
Insulation Thickness
Insulation Thickness
1'' 1-1/2" 2'' 2-1/2"
http://www.pipingtech.com/preis/cs2023.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
52/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
53/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
24'' 11605 16579 14-1/2" 22111 27'' 4'' 15" 23844 28'' 4'' 15-1/2" 25643 29'' 6'' 16" 27508 30'' 6''26'' 12573 17961 16-1/4" 25643 29-1/2'' 4'' 16-3/4" 27508 30-1/2'' 6'' 17-1/4" 29438 31-1/2'' 6'' 17-3/4" 31433 32-1/2'' 6''
28'' 13540 19342 17-1/4" 29438 31-1/2'' 4'' 17-3/4" 31433 32-1/2'' 6'' 18-1/4" 33493 33-1/2'' 6'' 18-3/4" 35619 34-1/2'' 6''
30'' 14507 20724 18-1/4" 33493 33-1/2'' 4'' 18-3/4" 35619 34-1/2'' 6'' 19-1/4" 37811 35-1/2'' 6'' 19-3/4" 40068 36-1/2'' 6''
32'' 15474 22106 19-1/4" 37811 35-1/2'' 4'' 19-3/4" 40068 36-1/2'' 6'' 20-1/4" 42390 37-1/2'' 6'' 20-3/4" 44778 38-1/2'' 6''
34'' 16441 23487 20-1/4" 42390 37-1/2'' 4'' 20-3/4" 44778 38-1/2'' 6'' 21-1/4" 47231 39-1/2'' 6'' 21-3/4" 49749 40-1/2'' 6''
36'' 17408 24869 21-1/4" 47231 39-1/2'' 4'' 21-3/4" 49749 40-1/2'' 6'' 22-1/4" 52333 41-1/2'' 6'' 22-3/4" 54983 42-1/2'' 6''
40'' 19342 27632 23-1/4" 57698 43-1/2'' 4'' 23-3/4" 60478 44-1/2'' 6'' 24-1/4" 63323 45-1/2'' 6'' 24-3/4" 66234 46-1/2'' 6''
42'' 20310 29014 24-1/4" 63323 45-1/2'' 4'' 24-3/4" 66234 46-1/2'' 6'' 25-1/4" 69211 47-1/2'' 6'' 25-3/4" 72253 48-1/2'' 6''
L=12" L=18"
Pipe Vert ical Vert ical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
24'' 11605 16579 16-1/2" 29438 31'' 6'' 17" 31433 32" 6" 17-1/2" 33493 33'' 8''
26'' 12573 17961 18-1/4" 33493 33-1/2'' 6'' 18-3/4" 35619 34-1/2" 6" 19-1/4" 37811 35-1/2'' 8''
28'' 13540 19342 19-1/4" 37811 35-1/2'' 6'' 19-3/4" 40068 36-1/2" 6" 20-1/4" 42390 37-1/2'' 8''
30'' 14507 20724 20-1/4" 42390 37-1/2'' 6'' 20-3/4" 44778 38-1/2" 6" 21-1/4" 47231 39-1/2'' 8''
32'' 15474 22106 21-1/4" 47231 39-1/2'' 6'' 21-3/4" 49749 40-1/2" 6" 22-1/4" 52333 41-1/2'' 8''
34'' 16441 23487 22-1/4" 52333 41-1/2'' 6'' 22-3/4" 54983 42-1/2" 6" 23-1/4" 57698 43-1/2'' 8''
36'' 17408 24869 23-1/4" 57698 43-1/2'' 6'' 23-3/4" 60478 44-1/2" 6" 24-1/4" 63323 45-1/2'' 8''
40'' 19342 27632 25-1/4" 69211 47-1/2'' 6'' 25-3/4" 72253 48-1/2" 6" 26-1/4" 75360 49-1/2'' 8''
42'' 20310 29014 26-1/4" 75360 49-1/2'' 6'' 26-3/4" 78533 50-1/2" 6" 27-1/4" 81771 51-1/2'' 8''
4"3-1/2"3"
Insulation Thickness
Insulation Thickness
1'' 1-1/2" 2'' 2-1/2"
http://www.pipingtech.com/preis/cs2030.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
54/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
55/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
24'' 11605 16579 12'' 22111 27'' 4'' 12'' 23844 28'' 4'' 13'' 25643 29'' 6'' 13'' 27508 30'' 6''26'' 12573 17961 14'' 25643 29-1/2'' 4'' 14'' 27508 30- 1/ 2'' 6'' 15'' 29438 31-1/2'' 6'' 15-1/ 2'' 31433 32-1/2'' 6''
2 8' ' 1 35 40 19 34 2 1 4-1/ 2' ' 29 43 8 3 1-1/ 2' ' 4 '' 1 5' ' 3 143 3 3 2-1/ 2' ' 6 '' 1 5-1/ 2' ' 33 49 3 3 3-1/ 2' ' 6 '' 1 6' ' 3 56 19 3 4-1/ 2' ' 6 ''
30'' 14507 20724 16'' 33493 33-1/2'' 4'' 16-1/2'' 35619 34- 1/ 2'' 6'' 18'' 37811 35-1/2'' 6'' 18'' 40068 36-1/2'' 6''
3 2' ' 1 54 74 22 10 6 18 '' 37 81 1 3 5-1/ 2' ' 4 '' 18 -1 /2 '' 4 006 8 3 6-1/ 2' ' 6 '' 1 8-1/ 2' ' 42 39 0 3 7-1/ 2' ' 6 '' 1 9' ' 4 47 78 3 8-1/ 2' ' 6 ''
34'' 16441 23487 18'' 42390 37-1/2'' 4'' 18-1/2'' 44778 38- 1/ 2'' 6'' 19'' 47231 39-1/2'' 6'' 20'' 49749 40-1/2'' 6''
3 6' ' 1 74 08 24 86 9 19 '' 47 23 1 3 9-1/ 2' ' 4 '' 1 9' ' 4 974 9 4 0-1/ 2' ' 6 '' 1 9-1/ 2' ' 52 33 3 4 1-1/ 2' ' 6 '' 19 -1 /2' ' 5 49 83 4 2-1/ 2' ' 6 ''
40'' 19342 27632 18'' 57698 43-1/2'' 4'' 18'' 60478 44-1/2'' 6'' 19'' 63323 45-1/2'' 6'' 20'' 66234 46-1/2'' 6''
42'' 20310 29014 18'' 63323 45-1/2'' 4'' 19'' 66234 46-1/2'' 6'' 20'' 69211 47-1/2'' 6'' 21'' 72253 48-1/2'' 6''
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
24'' 11605 16579 14'' 29438 31'' 6'' 16" 31433 32" 6" 16'' 33493 33'' 8''
26'' 12573 17961 16'' 33493 33-1/2'' 6'' 16" 35619 34-1/2" 6" 16'' 37811 35-1/2'' 8''28'' 13540 19342 16'' 37811 35-1/2'' 6'' 17" 40068 36-1/ 2" 6" 16-1/2'' 42390 37-1/2'' 8''
30'' 14507 20724 20'' 42390 37-1/2'' 6'' 20'' 44778 38-1/2" 6" 20'' 47231 39-1/2'' 8''
32'' 15474 22106 20'' 47231 39-1/2'' 6'' 21" 49749 40-1/2" 6" 21'' 52333 41-1/2'' 8''
3 4' ' 1 64 41 23 48 7 2 1-1/ 2' ' 52 33 3 4 1-1/ 2' ' 6 '' 2 2" 5 498 3 42 -1 /2" 6 " 2 1-1/ 2' ' 57 69 8 4 3-1/ 2' ' 8 ''
36'' 17408 24869 20'' 57698 43-1/2'' 6'' 21" 60478 44-1/2" 6" 21'' 63323 45-1/2'' 8''
40'' 19342 27632 21'' 69211 47-1/2'' 6'' 22" 72253 48-1/2" 6" 22'' 75360 49-1/2'' 8''
42'' 20310 29014 22'' 75360 49-1/2'' 6'' 23" 78533 50-1/2" 6" 23'' 81771 51-1/2'' 8''
4"3-1/2"3"
Insulation Thickness
Insulation Thickness
1'' 1-1/2" 2'' 2-1/2"
http://www.pipingtech.com/preis/cs2031.htm
7/25/2019 Pre Insulated Pipe Supports Catalogue
56/206
7/25/2019 Pre Insulated Pipe Supports Catalogue
57/206
L=12" L=18"
Pipe Vertical Vertical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
24'' 11605 16579 14-1/2" 22111 27'' 4'' 15" 23844 28'' 4'' 15-1/2" 25643 29'' 6'' 16" 27508 30'' 6''
26'' 12573 17961 16-1/4" 25643 29-1/2'' 4'' 16-3/4" 27508 30-1/2'' 6'' 17-1/4" 29438 31-1/2'' 6'' 17-3/4" 31433 32-1/2'' 6''
28'' 13540 19342 17-1/4" 29438 31-1/2'' 4'' 17-3/4" 31433 32-1/2'' 6'' 18-1/4" 33493 33-1/2'' 6'' 18-3/4" 35619 34-1/2'' 6''
30'' 14507 20724 18-1/4" 33493 33-1/2'' 4'' 18-3/4" 35619 34-1/2'' 6'' 19-1/4" 37811 35-1/2'' 6'' 19-3/4" 40068 36-1/2'' 6''
32'' 15474 22106 19-1/4" 37811 35-1/2'' 4'' 19-3/4" 40068 36-1/2'' 6'' 20-1/4" 42390 37-1/2'' 6'' 20-3/4" 44778 38-1/2'' 6''
34'' 16441 23487 20-1/4" 42390 37-1/2'' 4'' 20-3/4" 44778 38-1/2'' 6'' 21-1/4" 47231 39-1/2'' 6'' 21-3/4" 49749 40-1/2'' 6''
36'' 17408 24869 21-1/4" 47231 39-1/2'' 4'' 21-3/4" 49749 40-1/2'' 6'' 22-1/4" 52333 41-1/2'' 6'' 22-3/4" 54983 42-1/2'' 6''
40'' 19342 27632 23-1/4" 57698 43-1/2'' 4'' 23-3/4" 60478 44-1/2'' 6'' 24-1/4" 63323 45-1/2'' 6'' 24-3/4" 66234 46-1/2'' 6''
42'' 20310 29014 24-1/4" 63323 45-1/2'' 4'' 24-3/4" 66234 46-1/2'' 6'' 25-1/4" 69211 47-1/2'' 6'' 25-3/4" 72253 48-1/2'' 6''
L=12" L=18"
Pipe Vert ical Vert ical
size Load(lbs) Load(lbs)
W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H W
Axial
load
(lbs.) O.D. H
24'' 11605 16579 16-1/2" 29438 31'' 6'' 17" 31433 32" 6" 17-1/2" 33493 33'' 8''
26'' 12573 17961 18-1/4" 33493 33-1/2'' 6'' 18-3/4" 35619 34-1/2" 6" 19-1/4" 37811 35-1/2'' 8''28'' 13540 19342 19-1/4" 37811 35-1/2'' 6'' 19-3/4" 40068 36-1/2" 6" 20-1/4" 42390 37-1/2'' 8''
30'' 14507 20724 20-1/4" 42390 37-1/2'' 6'' 20-3/4" 44778 38-1/2" 6" 21-1/4" 47231 39-1/2'' 8''
32'' 15474 22106 21-1/4" 47231 39-1/2'' 6'' 21-3/4" 49749 40-1/2" 6" 22-1/4" 52333 41-1/2'' 8''
34'' 16441 23487 22-1/4" 52333 41-1/2'' 6'' 22-3/4" 54983 42-1/2" 6" 23-1/4" 57698 43-1/2'' 8''
36'' 17408 24869 23-1/4" 57698 43-1/2'' 6'' 23-3/4" 60478 44-1/2" 6" 24-1/4" 63323 45-1/2'' 8''
40'' 19342 27632 25-1/4" 69211 47-1/2'' 6'' 25-3/4" 72253 48-1/2" 6" 26-1/4" 75360 49-1/2'' 8''
42'' 20310 29014 26-1/4" 75360 49-1/2'' 6'' 26-3/4" 78533 50-1/2" 6" 27-1/4" 81771 51-1/2'' 8''
Insulation Thickness
1
Top Related