7/28/2019 Pilot WheelBearing Replace
1/11
Zoom
Sized for Print
Knuckle/Hub ReplacementSpecial Tools Required
Ball joint remover, 28 mm 07MAC-SL00200
7/28/2019 Pilot WheelBearing Replace
2/11
Hub dis/assembly tool 07GAF-SE00100
Attachment, 62 x 68 mm 07746-0010500
Driver 07749-0010000
Support base 07965-SD90100
Attachment, 96 mm 07948-SB00101
Attachment, 86 mm 07VAD-P8A010A
1. Raise the front of the vehicle, and make sure it is securely supported.
Zoom
Sized for Print
2. Remove the wheel nuts and frontwheels.
http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34865429http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34865429http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34865429http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/348654297/28/2019 Pilot WheelBearing Replace
3/11
Zoom
Sized for Print
3. Remove the brake hose mounting bolt (A).
4. Remove the caliper mounting bolts (B), and hang the caliper assembly (C) to one side. To
prevent damage to the caliper assembly or brake hose, use a short piece of wire to hang the
caliper from the undercarriage.
Zoom
Sized for Print
5. Remove the wheel sensor (A) from the knuckle (B). Do not disconnect the wheel sensor
connector.
7/28/2019 Pilot WheelBearing Replace
4/11
Zoom
Sized for Print
6. Raise the stake (A) of the spindle nut (B), then remove and discard the nut.
Zoom
Sized for Print
7. Remove the brake disc retaining screws (A).
7/28/2019 Pilot WheelBearing Replace
5/11
8. Screw two 8 x 1.25 mm bolts (B) into the brake disc to push it away from the hub. Turn each bolt
two turns at a time to prevent cocking the disc excessively.
9. Remove the brake disc from the hub.
10.Check the front hub for damage and cracks.
Zoom
Sized for Print
11.Remove the cotter pin (A) from the tie-rod end ball joint, then loosen the nut (B).
12.Remove the tie-rod ball joint from the knuckle using the special tool.
7/28/2019 Pilot WheelBearing Replace
6/11
Zoom
Sized for Print
13.Remove the lock pin (A) from the lower arm ball joint castle nut (B), and remove the nut.NOTE:
Do not force or hammer on the lower arm, or pry between the lower arm and the knuckle. You
could damage the ball joint.
14.Remove the lower arm ball joint from the knuckle using the special tool.
Zoom
Sized for Print
15.Remove the damper pinch bolts (A) and flange nuts (B) from the damper.
16.Pull the knuckle outward, and remove the driveshaft outboard joint (C) from the knuckle (D) bytapping the driveshaft end (E) with a plastic hammer, then remove the knuckle.
7/28/2019 Pilot WheelBearing Replace
7/11
Zoom
Sized for Print
17.Separate the hub (A) from the knuckle (B) using the special tool and a hydraulic press. Be careful
not to deform the splash guard. Hold onto the hub to keep it from falling when pressed clear.
Zoom
Sized for Print
7/28/2019 Pilot WheelBearing Replace
8/11
18.Remove the snap ring (A) and the splash guard (B) from the knuckle (C).
Zoom
Sized for Print
19.Press thewheel bearing(A) out of the knuckle (B) using the special tools and a press.
Zoom
Sized for Print
http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/348721077/28/2019 Pilot WheelBearing Replace
9/11
20.Press thewheel bearinginner race (A) from the hub (B) using the special tool, a commercially
available bearing separator (C), and a press.
21.Wash the knuckle and hub thoroughly in high flash point solvent before reassembly.
Zoom
Sized for Print
22.Press a newwheel bearing(A) into the knuckle (B) using the old bearing (C), a steel plate (D), the
special tool, and a press. Be careful not to damage the sleeve of the pack seal.
http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/34872107http://alldatapro.com/alldata/PRO~V149865073~C40339~R0~OD~N/0/101825161/105707452/105707457/110688997/34853741/56180732/34865428/348721077/28/2019 Pilot WheelBearing Replace
10/11
Zoom
Sized for Print
23.Install the snap ring (A) securely in the knuckle (B).
24.Install the splash guard (C), and tighten the screws (D).
Zoom
Sized for Print
25.Install the hub (A) onto the knuckle (B) using the special tools and a press. Be careful not to
deform the splash guard (C).
26.Install the knuckle in the reverse order of removal, and note these items:
Be careful not to damage the ball joint boots when installing the knuckle.
Tighten all mounting hardware to the specified torque values. Torque the castle nut to the lower torque specification, then tighten it only far enough
to align the slot with the pin hole. Do not align the castle nut by loosening it.
Install a new lock pin on the castle nut after torquing.
Use a new spindle nut on reassembly.
Before installing the new spindle nut, apply a small amount of engine oil to the seating
surface of the nut. After tightening, use a drift to stake the spindle nut shoulder against
the driveshaft.
7/28/2019 Pilot WheelBearing Replace
11/11
Before installing the brake disc, clean the mating surfaces of the front hub and the
inside of the brake disc.
Before installing the wheel, clean the mating surfaces of the brake disc and the inside of
the wheel.
Check the front wheel alignment, and adjust it if necessary.
Top Related