8/13/2019 Optical Sensor Product Guide-Lr
1/60
Optoisolation and Optical Sensor Products
Selection Catalog
Your Imagination, Our Innovation
Sense Illuminate Connect
8/13/2019 Optical Sensor Product Guide-Lr
2/60
Optoisolation Products
9 Multi-Channel & Bi-Directional Digital Optocoupler
10 High Speed Digital CMOS Logic Gate Optocoupler
12 20 MBd Logic Gate Optocoupler
13 10 MBd Logic Gate/CMOS Optocoupler16 8 MBd Logic Gate Optocoupler
17 5 MBd Logic Gate Optocoupler
18 1 MBd Transistor Output Optocoupler
19 100 kBd Darlington Transistor Output Optocoupler
20 R2Coupler (High Temperature, Automotive Grade)
24 Digital Isolator
25 Miniature Analog Isolation Amplifier
27 Integrated Gate Drive Optocoupler
30 Intelligent Power Module Interface Optocoupler
32 Isolated Line Receiver
33 Isolated 20 mA Current Loop Transmitter/Receiver
34 Isolated Voltage/Current Detector
35 High Linearity Analog Optocoupler
36 Wideband Analog/Video Optocoupler
37 General Purpose Phototransistor Optocoupler
39 Solid State Relay (Photo MOSFET)
42 Powerline Communication Interface
43 Hermetic High Performance Optocoupler
47 Package Drawings
57 Function vs Application Matrix
Optical Sensors
59 Proximity and Ambient Light Sensors
8/13/2019 Optical Sensor Product Guide-Lr
3/60
3
Avago Technologies offers the
industrys best isolation technologyalong with the industrys leading
CMR performance
Avago Technologies optocouplers can be used in an array of isolation applications ranging
from power supply and motor control circuits to data communications and digital logicinterface circuits.
The primary purpose of an optocoupler is to provide both electrical insulation and signal
isolation. The popularity of Avago Technologies optocouplers is due to cost effectiveinnovations in these areas.
Optocouplers eliminate the effects of electrical noise caused by crosstalk, power glitches andelectrical interference. They provide high voltage isolation allowing safe interface between
high and low voltages in electrical circuits. They are also used for shifting logic levels.Avago Technologies key products include optocouplers with phototransistor output,
digital and analog output, high speed and high gain performance, drivers for isolatedgate transistors and intelligent power modules, smart current sensors, solid state relay
(Photo MOSFET) and other application specific devices.
Avago Technologies offers the industrys best isolation technology along with the industrys
leading CMR performance of up to 40 kV/s in a broad line of packages. Products include
the lowest power dissipation with input current as low as 40 A, high speed digitaloptocouplers operating at up to 50 MBd, propagation delays as low as 22 ns, 3.3 V JEDECcompatible optocouplers. Avago Technologies optocouplers are manufactured with high
quality and reliability and have worldwide safety approvals including the highest maximuminsulation voltage (VIORM) at 2262 V (per IEC/EN/DIN EN 60747-5-2/5).
8/13/2019 Optical Sensor Product Guide-Lr
4/60
4
Avago Technologies offers a broad range of isolation products
that provide performance features and benefits that are
unmatched in the industry for industrial, computing, consumer,communication, medical, military and aerospace markets.
Applications for Avago Technologies Isolation Products
Industrial
The widest portfolio of
optocouplers to meet theextensive requirements
of applications in factoryautomation.
Automated test equipment
Battery operated vehicle
Fieldbus
Industrial communications
Industrial networking
Motor control
PLC input/output isolation
Power distribution systems
Power generation
Renewable energy power
generation
Robotics
Switching panel
Switching power supplies
Test and measurementequipment
Automotive
Avago Technologiesautomotive R2Coupler areAEC-Q100 qualified with
applications in:
Automotive andshipboard system CANBusinterface isolation
Motor inverter drives
DC-DC converters/inverters for batterychargers
Battery/inverter voltagemonitoring
Status/fault signal feedbackisolation interface
Heating, ventilation andair-conditioning
Medical
Avago Technologiesoffers optocouplers with
high linearity and high
resolution for severeisolation requirements to:
Debrillators
ECG/EKG
Endoscopes
Magnetic resonanceimaging
Patient monitoring
Computers and OfficeEquipment
Avago Technologies
optocouplers with CMOScompatibility and high
speed are used to provideinterface isolation for:
Isolated input/outputmodule
Isolated USB hub
Printers and plotters
Communications
Avago Technologiesprovides high speed
optocouplers in both singleand dual surface-mount
packages which are used in:
Automated meteringreading
Digital cross connect
Distributed powerarchitecture
ISDN
Modems
PBX and central oce
Power linecommunication
Power over ethernet
Telephone switchingequipment
Telephone terminalequipment
Wireless base station
Consumer Electronics
Avago Technologiesoffers lower solution costswith highly integrated
optocouplers for manyconsumer applications,
such as:
Air conditioning
Alarm systems Audio and video
equipment
Electronic gaming
Fitness equipment
Induction cookers
Plasma displays
Washing machines
Military and Aerospace
Avago Technologies highreliability optocouplers are
suitable for military andaerospace applications
such as:
Aircraft, satellite and spacesystems
Communications
Computers
Test systems
Defense systems
Avago, Avago Technologes, the A logo, R 2Coupler are trademarks of Avago Technologies in the United States and other countries.
8/13/2019 Optical Sensor Product Guide-Lr
5/60
5
Upgrade Part Feature Benefit
High Voltage Insulation
Improved Isolation/Insulation
Ability to protect surrounding circuitry against physicaldamages resulting from differential voltages.
ACNV family offers highest available working voltageratingswith regulatory approval per IEC/EN/DIN EN 60747-5-2/5 of2262 V peak.
Meets international safety regulations and standards.Provides better isolationand overall safetyperformance.
Noise Isolation
High CMR
Common-mode transient rejection or signal isolation of datathrough suppression of noise transients.
Offers guaranteed CMR performance up to 40 kV/swhich isthe highest available in the market.
Improves system performance, and reliability.More robustsystems and better data integritymeet EMI and ESDrequirements.
Power Consumption
Drive Current, IF
Low Drive Current, LED drive current.
Offers the lowest IF(as low as 40 A)devices in the marketand broadest HCMOS compatibility.
Eliminates additional LED drive circuitry. Improvessystem efficiency and reduces power consumption and LEDdegradation.
Lower Power Supply
Lower power supply (3.3V)
Lower the power consumptionand meets JEDEC low voltagerequirements.
Up to 50%energy saving.
Flexible Supply Voltages(3.3V/5V)
Support a combination of two different supply voltages at theinput and output.
Built-in internal level shifter,eliminate the need of extrapower supply. 3.3V or 5V.3.3V helps to improve the overall power consumption.
Temperature
Temperature
The DC, speed performance and the reliability information isensured at the specific temperature range.
Support up to -40C to 125Ct emperature range. Allow extreme temperature operation.
Speed Benefits
Propagation Delay, tpDescribes how quickly a logic signal can propagate throughthe system.
High speed digital optocouplers to meet wide range ofapplications with tp as low as 22 ns. Increase switching efficiencyand better speed performance.
Upgrade Pulse Width Distortion, PWD
PWD is the difference between tPHLand tPHLand oftendetermines the maximum data rate capability of atransmission system.
The lowest PWD offered by optocoupler is2 ns. To ensure signal data integrityover long bus line.
Package and Space Savings
Multi-Channels,Bi-directional Features
Integrateddual, triple, quadwith bi-directionalchannelsoffers in small SO8 and SO16 package.
The integrated bi-directional channels help in space savingsand ease of designs.
Surface Mount Device
SMD permits more component density than DIP.
Smaller package to deliver the same functionalityas standard DIP.
True surface mount technology and standard footprint.
Lower assembly cost,easier and faster handling as well asbetter solderability.
8mm Clearance/Creepage (C/C) Packages The package is 50% smaller than conventional DIP package.It can withstand high isolation voltages and meet regulatoryrequirements such as IEC/UL/CSA standards.
Provides space savings.Allows high voltage surgeprotection. Meets many IEC/UL/CSA equipment standardsthat call for clearance and creepage of 8mm.
Smaller SO5 Package Smaller SO5package (as compared to existing SO-8 package) Provides greater than 40% space savings.
Quick Guide to Direct Upgrades
8/13/2019 Optical Sensor Product Guide-Lr
6/60
6
Existing Parts Upgrade Parts Upgrade Features Footprint Information
High Speed Family (>12.5MBd)
HCPL-0708 ACPL-071L Flexible supply voltages (3.3V/5V) Lower Propagation Delay (
8/13/2019 Optical Sensor Product Guide-Lr
7/60
8/13/2019 Optical Sensor Product Guide-Lr
8/60
8
Existing Parts Upgrade Parts Upgrade Features Footprint Information
Intelligent Power Module Interface Optocoupler
HCPL-4502HCPL-4503
ACPL-K453 8mm Creepage and Clearance 50% smaller package size
Smaller footprint
HCPL-4504 ACPL-W454 8mm Creepage and Clearance 50% smaller package size
Smaller footprint
ACPL-P454 8mm Creepage 50% smaller package size
Smaller footprint
HCPL-4506 ACPL-W456 8mm Creepage and Clearance 50% smaller package size
Smaller footprint
ACPL-P456 8mm Creepage 50% smaller package size
Smaller footprint
ACPL-4800 ACPL-W480 8mm Creepage and Clearance 50% smaller package size
Smaller footprint
ACPL-P480 8mm Creepage
50% smaller package size
Smaller footprint
HCPL-M452/3/4/6 ACPL-M484 Higher CMR 30kV/s 10MBd speed Totem-pole output, positive logic
Faster speed
HCPL-4502/03/04/06HCPL-0452/53/54/66
ACPL-W484 8mm Creepage and Clearance Higher CMR 30kV/s 10MBd speed Totem-pole output, positive logic
Faster speed
HCNW4502/03/04/06 ACNV4506 13mm Creepage and Clearance Higher Working Voltage Viorm 2262Vpk Higher CMR 30kV/s Totem-pole output, positive logic
Higher Working Voltage
HCPL-M452/53/54 ACPL-M43U Wide temperature (-40C to 125C)
Low LED input drive current IF 10mA
Drop-in replacement
HCPL-M456 ACPL-M46U Wide temperature (-40C to 125C) Drop-in replacement
General Purpose Phototransistor Optocoupler
HCPL-817 ACPL-827ACPL-847
Multi-channel. 2-ch and 4-ch Higher Integrations
HCPL-814 ACPL-824ACPL-844
Multi-channel. 2-ch and 4-ch Higher Integrations
HCPL-181/817 ACPL-217 Smaller package (SO4 half-pitch) CMR 10kV/s (typ) Extended Industrial -55 to 110C Viso 3kVrms (1min)
Smaller footprint
HCPL-354/814 ACPL-214 Smaller package (SO4 half-pitch)
CMR 10kV/s (typ) Extended Industrial -55 to 110C Viso 3kVrms (1min)
Smaller footprint
Note:
Drop-in replacementmeans no PCB board redesign is required,
Pin-to-Pinmeans the footprint is same but requires minimum PCB board redesign (eg. Removing of external resistor)
* Lower speed
^ Advanced information, may subject to changes.
8/13/2019 Optical Sensor Product Guide-Lr
9/60
8/13/2019 Optical Sensor Product Guide-Lr
10/60
10
Optoisolation and Optical Sensor Products
High Speed Digital CMOS Logic Gate Optocoupler
DescriptionThese optocouplers use the latest CMOS IC
technology to achieve outstanding perfor-mance with very low power consumption.
Serial fieldbuses are used today primarily asthe communication system for the exchangeof information between automation system
and distributed eld devices. PROFIBUS is
the leading open fieldbus system and it has
worldwide acceptance. PROFIBUS is es-sentially a twisted wire pair serial link that
is very similar to RS 485. Profibus speed
standard is either lower speed (1.5 MBd) orhigher speed (12 MBd).
In this isolated multipoint transmissionapplication circuit, two different optoisolators
are utilized (HCPL-0721 and HCPL-061N).The benefits include low input drive current
that maximizes LED lifetime/reliability andoptimizes speed for Profibus and RS-485
applications.
Benefits High speed (up to 50 MBd)
3.3V/5V dual supply voltage available
Wide temperature operation -40C to100C (HCPL-x710)
Low PWD (2ns) & low tp (22ns) to meetDeviceNet and Profibus application
Buer input and CMOS output toeliminate any pull-up resistor
5 kV isolation voltage (HCPL-77xx)
Dual channel device is available to
save space(HCPL-0738) Certied with reinforced insulation
under IEC/EN/DIN EN 60747-5-2
Applications
AC plasma displaypanel level shifting
CAN Bus
CC_Link
Microprocessor
system interface Mutiplexed data
transmission
Switchingpower supply
X
X
X
CC
T
5V ISO 5V
7
1
2
3
4
6
5SHIELD
ACPL-072L
0.01
0.01F
R
1
5V ISO 5V
8
8
7
6
5
3
4
SHIELD
ACPL-072L
0.01
0.01
T
1
2
2
8
7
6
5
3
4
SHIELD
ACPL-061L^
TENABLE
5V
ISO 5V
0.01
680
1M
ISO 5V
REG
0.01
+6
75ALS176D
8
R
7
A
R
D
DE
RE
B
0.01
GND
V1
4
3
2
5
ISO 5V
F
F
F
F
F
F
Typical Profibus Block Diagram
8/13/2019 Optical Sensor Product Guide-Lr
11/60
11
Optoisolation and Optical Sensor Products
High Speed Digital CMOS Logic Gate Optocoupler Product Selection
Device Part No. Package VDDV
IF(on)mA
Min.
Max DataRate MBd
Min.
tPLHns
Max.
tPHLns
Max.
PWDns
Max.
tPSKns
Max.
CMR - V/s@VCM VISOVRMS
Min.
VIORMV
peakCMRV/s (Min.)
VCMV
Single Channel CMOS Input HCPL-0710 SO8 5 12.5 40 40 8 20 10000 1000 3750 560*
HCPL-0720 SO8 5 25 40 40 8 20 10000 1000 3750 560*
HCPL-0721 SO8 5 25 40 40 6 20 10000 1000 3750 560*
HCPL-0723 SO8 5 50 22 22 2 16 10000 1000 3750 560*
HCPL-7710 300 mil DIP8 5 12.5 40 40 8 20 10000 1000 3750/5000# 630*
HCPL-7721 300 mil DIP8 5 25 40 40 6 20 10000 1000 3750/5000# 630*
HCPL-7720 300 mil DIP8 5 25 40 40 8 20 10000 1000 3750/5000# 630*
HCPL-7723 300 mil DIP8 5 50 22 22 2 16 10000 1000 3750/5000# 630*
LED Input HCPL-0708 SO8 5 10 15 60 60 30 40 10000 1000 3750 560*
Dual Channel LED Input HCPL-0738 SO8 5 10 15 60 60 30 40 10000 1000 3750 560*
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, #- with UL5000VRMS /1 minute Option 020
1
SHIELD
D1
V1
GND1
D
VO
GND
NC
IOED1
VDD
NC
VO
GND
NC 1
2
3
4
8
7
6
5
ANODE
CATHODE
NC
VDD2
VO2
VO1
GND
1
2
3
4
8
7
6
5
ANODE1
ANODE2
CATHODE2
CATHODE1
3.3V/5V Family (15/25 MBd High Speed Digital CMOS Optocoupler)
Device Part No. Package VDDV
IF(on)mAMin.
Max.Data RateMBd Min.
tPLHnsMax.
tPHLnsMax.
PWDnsMax.
tPSKnsMax.
CMR - V/s@VCM VISOVRMSMin.
VIORMVpeakCMR
V/s (Min.)VCMV
Single Channel CMOS Input ACPL-072L-000E SO8 3.3/5 25 40 40 6 20 10000 1000 3750 560*
ACPL-772L-000E 300 milDIP8
3.3/5 25 40 40 6 20 10000 1000 3750/5000 #
630*
Single Channel LED Input ACPL-071L-000E SO8 3.3/5 10 15 40 40 25 30 10000 1000 3750 560*
ACPL-W70L-000E StretchedSO6
3.3/5 4 15 55 55 25 40 10000 1000 5000 1140*
ACPL-M75L-000E SO5 3.3/5 4 15 55 55 25 40 10000 1000 3750 560*
Dual Channel LED Input ACPL-074L-000E SO8 3.3/5 10 15 40 40 25 30 10000 1000 3750 560*
ACPL-K73L-000E StretchedSO8
3.3/5 4 15 55 55 25 40 10000 1000 5000 1140*
Notes: * - with IEC/EN/DIN EN 60747-5-2 Option 060, #- with UL 5000V RMS /1 minute Option 020.
8
7
63
HIELD5
2
4
V D1
V1
ND1
VDD2
VO
GND2
NC
OLED1
VO
VDD
GND
1
2
3
5
ANODE
CATHODE
4
VDD
NC
VO
GND
NC 1
2
3
4
8
7
6
5
ANODE
CATHODE
NC
VO
VDD
GND
1
2
3
6
5
4
ANODE
NC*
CATHODE
VDD2
VO2
VO1
GND
1
2
3
4
8
7
6
5
ANODE1
ANODE2
CATHODE2
CATHODE1
VO1
VDD
GND
1
2
3
8
7
5
ANODE 1
CATHODE 1
CATHODE 2
4ANODE 2
VO26
NEW
NEW
NEW
NEW
NEW
NEW
NEW
8/13/2019 Optical Sensor Product Guide-Lr
12/60
8/13/2019 Optical Sensor Product Guide-Lr
13/60
13
Optoisolation and Optical Sensor Products
DescriptionThis isolated RS-422 circuit uses two
high-speed optocouplers that can switchup to 10 MBd signals. An isolated pow-
er supply VCC2 is required to power theDS 75176A driver/receiver integrated circuit.
The main benef it i s preventing common-mode transients from interfering with thesignal.
Avagos new range of 3.3 V/5 V optocouplersare the first commercially available optocou-plers designed to meet the JEDEC specifica-tion for 3.3 V LVTTL/LVCMOS logic, therebysimplifying the implementation of isolationin systems utilizing 3.3 V logic circuits.
A typical Power over Ethernet powersource equipment (PSE) block diagram usestwo 15 MBd 3.3 V optocouplers to isolatebetween the 13 W 48 V power supply and
the inter-integrated chip (I2C) control bus.
Benefits
Provides high data rate transmission. Italso offer high CMR for signal isolationfrom common mode transient noises
Applications
Computer-peripheralinterface
Instrument input/outputisolation
Isolated line receiver
Microprocessor systeminterface
Switching power supply
Typical RS-422 Interface Block Diagram
10 MBd Logic Gate/ CMOS Optocoupler
Typical Power over Ethernet Power Source Block Diagram
8/13/2019 Optical Sensor Product Guide-Lr
14/60
8/13/2019 Optical Sensor Product Guide-Lr
15/60
15
Optoisolation and Optical Sensor Products
3.3V/5V Family (10 MBd CMOS Optocoupler)
Device Part No. Package VDDV
IF(on)mA
Min.
Max.Data Rate
MBd Min.
tPLHns
Max.
tPHLns
Max.
PWDns
Max.
tPSKns
Max.
CMR - V/s@VCM VISOVRMS
Min.
VIORMV
peakCMRV/s (Min.)
VCM
V
Single Channel LED Input ACPL-061L-000E^ SO8 3.3/5 1.6 10 80 80 30 30 20000 1000 3750 560*
ACPL-C61L-000E^ StretchedSO8
3.3/5 2.5 10 110 110 40 40 20000 1000 3750 1140*
ACNW261L-000E^ 400 mil DIP 3.3/5 2.5 10 120 120 50 40 20000 1000 3750 1414*
ACPL-W61L-000E StretchedSO6
3.3/5 1.6 10 80 80 30 30 20000 1000 5000 1140*
ACPL-M61L-000E SO5 3.3/5 1.6 10 80 80 30 30 20000 1000 3750 560*
ACPL-M62L-000E ^ SO5 3.3/5 1.6 10 80 80 30 30 20000 1000 3750 560*
Dual Channel LED Input ACPL-064L-000E SO8 3.3/5 1.6 10 80 80 30 30 20000 1000 3750 560*
ACPL-K64L-000E StretchedSO8
3.3/5 1.6 10 80 80 30 30 20000 1000 5000 1140*
Notes: * - with IEC/EN/DIN EN 60747-5-2 Option 060, #- with UL 5000V RMS /1 minute Option 020, ^ - Advanced Information, may subject to changes.
VO
VDD
GND
1
2
3
5
ANODE
CATHODE
4
VO
VDD
GND
1
3
4
6
ANODE
CATHODE
5
VO
VDD
GND
1
2
3
5
ANODE
CATHODE
4
VDD
VE
VO
GND
NC 1
2
3
4
8
7
6
5
ANODE
CATHODE
NC
VDD
VE
VO
GND
NC 1
2
3
4
8
7
6
5
ANODE
CATHODE
NCSHIELD
VDD2
VO2
VO
GND
1
2
4
6
5
ANODE1
ANODE2
CATHODE1
V D 2
O
VO
GND
1
2
3
4
6
5
ANODE1
ANODE2
CATHODE2
CATHODE1
NEW
NEW
NEW
NEW
NEW
8/13/2019 Optical Sensor Product Guide-Lr
16/60
16
Optoisolation and Optical Sensor Products
DescriptionThe circuit shows a CMOS interface circuit
for 8 MBd applications. Over the tempera-ture range a CMOS CD4050 Hex Buffer
can source about 0.7 mA (minimum), whichis sucient to drive the HCPL-2300 opto-coupler. The 20 pF capacitor allows peaking
currents to assist the LED in turning on andoff quickly.
These optocouplers utilize a simple interfacerequiring low power consumption.
Benefits Oers low power consumption
8 MBd Logic Gate Optocoupler Product Selection
Device Part No. Package IF(on)mAMin.
tPLHsMax.
tPHLsMax.
CMR - V/s@VCM VISOVRMSMin.
VIORMVpeakCMR V/s (Min.) VCM
V
Single Channel HCPL-0300 SO8 0.5 0.16 0.2 100 50 3750
HCPL-2300 300 mil DIP8 0.5 0.16 0.2 100 50 3750 630*
Notes:
* - with IEC/EN/DIN EN 60747-5-2/5 Option 060
1
4
8
7
6
5
VCC
VD
RL
GND
2
3
Anode
Cathode
Applications
Computer-peripheralinterface
Digital isolation forA/D, D/A conversion
High speed, long
distance isolatedline receiver
Level shifting
RS 232C interface
Typical CMOS Interface Block Diagram
8 MBd Logic Gate Optocoupler
8/13/2019 Optical Sensor Product Guide-Lr
17/60
17
Optoisolation and Optical Sensor Products
DC Bus
ontrol
Circuit
PWM
Controller
Gate
Driver
Power
Switch
Digital
Optocoupler
Output(AC-DC)
DC Output
Output
Recti er
Trans ormer
DescriptionThe circuit shown in the typical TTL interface
block diagram is an interface between twoTTL gates using an active output (totem
pole) optocoupler, the HCPL-2201. A seriesswitching circuit drives the optocouplerLED. The active output HCPL-2201 can be
directly connected to a TTL gate, and nopull-up resistor is required. The HCPL-2201
can sink enough current to handle up to16 LSTTL or 4 TTL loads.
Typically, the 5 MBd logic gate optocoupler
is used in the Isolated High-Low Gate Driveinterface block diagram as shown below.
Benefits Pull up resistor not required at the
optocoupler output
Low power on the optocoupler inputcircuit
Wide operating supply voltagesup to 20V
Built-in Schmitt Triggers for better signalintegrity and accuracy in a noisy network/circuits.
5 MBd Logic Gate Optocoupler Product Selection
Device Part No. Package IF(on)mAMin.
tPLHsMax.
tPHLsMax.
CMR - V/s@VCM VISOVRMSMin.
VIORMVpeakCMR V/s (Min.) VCM
V
Single Channel HCNW2201 400 mil DIP8 1.6 0.3 0.3 1000 50 5000 1414HCNW2211 400 mil DIP8 1.6 0.3 0.3 10000 1000 5000 1414HCPL-0201 SO8 1.6 0.3 0.3 1000 50 3750 560*HCPL-0211 SO8 1.6 0.3 0.3 10000 1000 3750 560*HCPL-2219 300 mil DIP8 1.6 0.3 0.3 2500 400 3750 630*
HCPL-2200 300 mil DIP8 1.6 0.3 0.3 1000 50 3750 630*HCPL-2201 300 mil DIP8 1.6 0.3 0.3 1000 50 3750 630*HCPL-2211 300 mil DIP8 1.6 0.3 0.3 10000 1000 3750 630*HCPL-2202 300 mil DIP8 1.6 0.3 0.3 1000 50 3750 630*
HCPL-2212 300 mil DIP8 1.6 0.3 0.3 10000 1000 3750 630*
Dual Channel HCPL-2231 300 mil DIP8 1.8 0.3 0.3 1000 50 3750
HCPL-2232 300 mil DIP8 1.8 0.3 0.3 10000 1000 3750
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060
7
1
2
3
4 5
6
8NC
ANOD
ATHODE
NC ND
V C
O
HIELD
ANODE
ATHOD
NC ND
V C
1
2
3
4 5
8ANODE
ANODE 2 GND
VCC
VO1
VO2
SHIELD
Isolated High-Low Gate Drive Interface Block Diagram
Typical TTL Interface Block Diagram
Applications
Computer-peripheralinterface
Ground loop
High speed line receiver
Microprocessor
system interface Pulse transformer
replacement
5 MBd Logic Gate Optocoupler
8/13/2019 Optical Sensor Product Guide-Lr
18/60
18
Optoisolation and Optical Sensor Products
1 MBd Transistor Output Optocoupler
DescriptionThe circuit in the level shifting/TTL interfaceblock diagram shows how a 0 to 5 V logicsignal can be level shifted to a -15 to 0 Vsignal. This circuit can safely be used forlevel shifting up to 800 V. The circuit usesan open collector output logic gate, the74LS405, to drive the LED of the 6N135/6optocoupler. The 6N135/6 also has an open-collector output. The designer chooses RINto agree with the equation shown in the
schematic. This equation sets the value ofthe optocoupler LED forward current. Theoutput of the 6N135/6 requires a pull-upresistor, RL. The current-transfer ratio (CTR) ofthe optocoupler determines the maximumamount of current the optocoupler outputcan sink while maintaining the outputvoltage (between pins 5 and 6) of 0.5 V or less.
The benefit of the application is that itreduces the transient immunity problem andit is a convenient way of replacing the pulsetransformer for high-voltage level shifting.
Benefits
Allow level shiftingcapability
High current transfer ratio
Applications
Analog signalground isolation
High speed logicground isolation
Line receivers
Replace pulsetransformers
Replace slowphototransistorisolators
Typical Level Shifting/TTL Interface Block Diagram
IF
7
5
6
8
2
3
4
1INR
74LS05
INR = 5 - VF
HCPL-050L
+5 V
IF
LR
OLV
-15 V
IO (min) = IF CTR (min)
R L (min) = 15 VOL
IO(min) + I IL
IILIO
V IN
VOUT
1 MBd Transistor Output Optocoupler Product Selection
Device Part No. Package VDDV MaxVDDV
IF(on)mAMin.
CTR tPLHsMax.
tPHLsMax.
CMR - V/s@VCM VISOVRMSMin.
VIORMVpeak
%Min.
%Max.
IFmA
CMRV/s (Min.)
VCMV
Single Channel 6N135 300 mil DIP8 5 15 16 7 50 16 2.0 2.0 1000 10 3750/5000 # 630*6N136 300 mil DIP8 5 15 16 19 50 16 1.0 1.0 1000 10 3750/5000 # 630*HCNW135 400 mil DIP8 5 15 16 5 16 2.0 2.0 1000 10 5000 1414HCNW136 400 mil DIP8 5 15 16 19 50 16 1.0 1.0 1000 10 5000 1414HCPL-050L SO8 3.3/5 15 16 15 50 16 1.0 1.0 1000 10 3750 560*HCPL-0500 SO8 5 15 16 7 50 16 2.0 2.0 1000 10 3750 560*HCPL-0501 SO8 5 15 16 19 50 16 1.0 1.0 1000 10 3750 560*HCPL-250L 300 mil DIP8 3.3/5 15 16 15 50 16 1.0 1.0 1000 10 3750/5000 # 630*HCPL-2502 300 mil DIP8 5 15 16 15 22 16 0.8 0.8 3750/5000 # HCPL-2503 300 mil DIP8 5 15 8 15 8 2.5 1.5 3750/5000 #
ACPL-M50L-000E SO5 3.3/5 24 3 80 200 3 1.0 1.0 15000 1000 3750 560*
ACPL-W50L-000E^ Stretched SO6 3.3/5 24 3 53 200 3 1.0 1.0 15000 1000 5000 1140*
Dual Channel HCPL-053L SO8 3.3/5 15 16 15 50 16 1.0 1.0 1000 10 3750 560*HCPL-0530 SO8 5 15 16 7 50 16 2.0 2.0 1000 10 3750 HCPL-0531 SO8 5 15 16 19 50 16 1.0 1.0 1000 10 3750 HCPL-253L 300 mil DIP8 3.3/5 15 16 15 50 16 1.0 1.0 1000 10 3750/5000 # 630*HCPL-2530 300 mil DIP8 5 15 16 7 50 16 2.0 2.0 1000 10 3750/5000 # HCPL-2531 300 mil DIP8 5 15 16 19 50 16 1.0 1.0 1000 10 3750/5000 # HCPL-2533 300 mil DIP8 5 15 8 15 8 2.5 1.5 3750 ACPL-054L-000E SO8 3.3/5 24 3 53 200 3 1.0 1.0 15000 1000 3750 560*ACPL-K54L-000E^ Stretched SO8 3.3/5 24 3 53 200 3 1.0 1.0 15000 1000 5000 1140*
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, #- with UL 5000V RMS/1 minute Option 020, ^ - Advanced information, may subject to changes.
NCAnode
athode V
GND
8
7
6
5
2
3
4
C
C
1
no e 1
at o 1
at o
no e
2
8
7
6
5
1
2
3
4
6
5
4
1
3
6
5
4
1
2
3
NEW
8/13/2019 Optical Sensor Product Guide-Lr
19/60
19
Optoisolation and Optical Sensor Products
m . . I L
1
1
4
1
1
.
IF
100 kBd Darlington Transistor Output Optocoupler Product Selection
Device Part No. Package VDDV
IF(on)mAMin.
CTR tPLHsMax.
tPHLsMax.
CMR - V/s@VCM VISOVRMSMin.
VIORMVpeak%
Min.%Max.
IFmA
CMRV/s (Min.)
VCMV
Single Channel 4N45 300 mil DIP6 5 0.5 200 1000 10 500 50 3750 630
4N46 300 mil DIP6 5 0.5 200 1000 10 500 50 3750 630
6N138 300 mil DIP8 5 0.5 300 2600 1.6 50 15 1000 10 3750/5000 #
6N139 300 mil DIP8 5 0.5 400 5000 0.5 90 2 1000 10 3750/5000 # 630*
HCNW138 400 mil DIP8 5 0.5 300 1.6 70 11 1000 10 5000 1414
HCNW139 400 mil DIP8 5 0.5 400 0.5 11 11 1000 10 5000 1414
HCPL-070A SO8 5 0.04 800 25000 0.04 25 60 1000 10 3750 560*
HCPL-070L SO8 3.3/5 0.5 400 5000 0.5 90 30 1000 10 3750 560*
HCPL-0700 SO8 5 0.5 300 2600 1.6 50 15 1000 10 3750 560*
HCPL-0701 SO8 5 0.5 400 5000 0.5 10 2 1000 10 3750 560*
HCPL-270L 300 mil DIP8 3.3/5 0.5 400 5000 0.5 90 30 1000 10 3750/5000 # 630*
HCPL-4701 300 mil DIP8 5 0.04 800 25000 0.04 90 25 1000 10 3750/5000# 630*
HCPL-M700 SO5 5 0.5 300 2600 1.6 35 20 1000 10 3750 HCPL-M701 SO5 5 0.5 400 3500 0.5 10 2 1000 10 3750
Dual Channel HCPL-073A SO8 5 0.04 800 25000 0.04 130 25 1000 10 3750
HCPL-073L SO8 3.3/5 0.5 400 5000 0.5 90 30 1000 10 3750 560*
HCPL-0730 SO8 5 0.5 400 5000 0.5 35 20 1000 10 3750
HCPL-0731 SO8 5 0.5 400 5000 0.5 35 20 1000 10 3750
HCPL-273L 300 mil DIP8 3.3/5 0.5 400 5000 0.5 90 30 1000 10 3750/5000 # 630*
HCPL-2730 300 mil DIP8 5 0.5 400 5000 0.5 35 20 1000 10 3750/5000#
HCPL-2731 300 mil DIP8 5 0.5 400 5000 0.5 60 20 1000 10 3750/5000#
HCPL-4731 300 mil DIP8 5 0.04 800 25000 0.04 90 25 1000 10 3750/5000#
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, #- with UL 5000V RMS /1 minute Option 020
100 kBd Darlington Transistor Output Optocoupler
DescriptionThis differentially driven circuit can use upto eight 6N138 optocouplers at variousreceivers along the 90 m line. All stationsare isolated. The first station would drawapproximately 2.7 mA current, and the laststation 1.8 mA of LED drive current. Theoutput grounds of the optocoupler may beelectrically separate.
The benefit of the application is its simple,low-cost, multidrop circuit for low signal-ing rates.
Benefits
High CTR with low input current
Low power consumption
Typical Multidrop Line Receiver Block Diagram
GND
C
out
no e
a t o e
6
4
1
GND
VCC
V01
Anode 1
Cathode1
Cathode2
Anode2
V02
8
7
6
5
1
2
3
4
Applications
Digital logic groundisolation
FIA RS-232C line receiver
Low power systems andground isolation
Telephone ring detector
VO
VB
GND
1
2
3
6
5
4
ANODE
CATHODE
VCCNC
NC
ANODE
CATHODE
VE
VO
GND
8
7
6
5
1
2
3
4
8/13/2019 Optical Sensor Product Guide-Lr
20/60
20
Optoisolation and Optical Sensor Products
R2Coupler (High Temperature, Automotive Grade)
DescriptionProven Quality and Reliability Track Record
Avago Technologies R2Coupler isolation prod-ucts are designed to meet the stringent re-quirements for the automotive market. Build-ing upon 35 years of optocoupler expertise,the automotive parts are manufactured in a TS16949 certified manufacturing facility and arePPAP supported. Robustness is demonstratedthrough qualification in accordance to AEC-Q100 Grade 1 guidelines. Avago optocouplershave been used extensively in long life andmission critical isolation applications such aslocomotive transportation, aerospace, militaryand industrial automation. Since the intro-duction of R2Coupler products in 2006, theseautomotive grade products have seen wideadoption by many automotive suppliers withmillions of units operating in the field.
Technology Leader
Avago Technologies is the first supplier to intro-duce 125C plastic optocouplers for automo-tive applications, with the largest portfolio ofoptocouplers ranging from IGBT gate drivers,isolation amplifier, high speed and low power
digital isolation and analog feedback isola-tion. Advanced LED technology enabled thebest-in-class performance over lifetime and athigh temperature. These optocouplers main-tain their very high voltage ratings with robustand reliable galvanic isolation technology withinternational component safety certifications(UL1577, IEC 60747-5-5, CSA Component Notice5). Optocouplers demonstrate superior EMIand common mode noise immunity.
Applications
Automotive IPM and gatedriver for inverters, DC-DCconverter and on-boardchargers
Automotive bus voltageand current/voltagesensing in inverters,converters and on-boardchargers
Automotive CANbus,UART, LIN and otherdigital communications
Isolated wake-up andstatus control andfeedback
Analog feedback in AC-DCand DC-DC converters
Low power digital
isolation in batterymanagement systems
Benefits Qualied to AEC-Q100 Grade 1 guidelines
TS 16949 manufacturing facility withPPAP support
Wide operating temperature (-40C to125C)
High CMR (30 kV/s at VCM=1kV)
Reinforced Reliability suitable forautomotive applications
Low input LED drive current
Worldwide Safety Approval (UL1577,IEC60747-5-5, CSA)
8/13/2019 Optical Sensor Product Guide-Lr
21/60
21
Optoisolation and Optical Sensor Products
Automotive CANBus Block DiagramTypical Intelligent Power Module/Electric MotorInverter Block Diagram
CANTransceiver
BusInterface
OtherDevices
UARTNetwork
Controller
Tx Rx
ACPL-M61T/M71T/M72T
OtherDevices
Micro-Controller
Controlled Devices, e.g.Air-Compressor,
Lighting Control, BatteryManagement System,
etc.
at
o
e
cc
out
roun
no
e
at
o
e
Vcc
Vout
round
Anode
Automotive 10MBd Logic Gate Optocoupler
Device Part No. Package VISO(1min)VRMS
VIORMVpeak
OperatingTemperatureC
VCCV
ILEDmA
dV/dtmA
tPLHMax.ns
tPHLMax.ns
PWDMax.
tPSKMax.
CMRdV/dtkV/s
VCMV
Single Channel
Anode
Cathode
VDD
VO
GND
6
5
4
1
3
ACPL-M71T SO5 4000 560 -40 to 125 3.0 to 5.5 4 to 15 1.5 35 35 12 15 15 1000
ACPL-K71T^ SSO8 5000 1140 -40 to 125 3.0 to 5.5 4 to 15 1.5 35 35 12 15 15 1000
ACPL-M72T SO5 4000 560 -40 to 125 3.0 to 5.5 4 to 15 1.5 100 100 50 60 25 1000
ACPL-K72T^ SSO8 5000 1140 -40 to 125 3.0 to 5.5 4 to 15 1.5 100 100 50 60 25 1000
Dual Channel LED Input
1
2
3
4
8
7
6
5
Anode1
Anode2
Cathode 1
Cathode 2
V 2DD
V 1D
VD2
GND
ACPL-K74T^ SSO8 5000 1140 -40 to 125 3.0 to 5.5 4 to 15 1.5 35 35 12 15 15 1000
ACPL-K75T^ SSO8 5000 1140 -40 to 125 3.0 to 5.5 4 to 15 1.5 100 100 50 60 25 1000
no e
atho e
C6
5
4
1
SHIELD
ACPL-M61T SO5 4000 560 -40 to 125 4.5 to 5.5 5 to 15 10 100 100 35 40 15 1000
Note: ^ - Advanced information, may subject to changes.
8/13/2019 Optical Sensor Product Guide-Lr
22/60
22
Optoisolation and Optical Sensor Products
Automotive Analog Optocoupler
Device Part No. Package VISOVRMS
VIORMVpeak
OperatingTemperatureC
VCCV
ILEDmA
CTRMin.%
(TA= 25 C) BWTyp.kHz
CMRdV/dtkV/s
CMRVCMVTyp.
%Min.%
6
5
4
1
3
ACPL-M43T SO5 4000 560 -40 to 125 20 5 to 15 20 45 32 1000 15 1500
ACPL-K43T^ SSO8 5000 1140 -40 to 125 20 5 to 15 24 65 32 1000 15 1500
ACPL-M49T SO5 4000 560 -40 to 125 20 4 to 10 20 45 32 15 1500
ACPL-K49T^ SSO8 5000 1140 -40 to 125 20 4 to 10 24 58 32 15 1500
Automotive Gate Drive Optocoupler
Device Features Part No. Package VISOVRMS
VIORMVpeak
OperatingTemperatureC
VCCV
ILEDTyp.mA
lo_peakMax.A
ICCMax.mA
tPHLMax.ns
tPHLMax.ns
PWDMax.ns
tPSKMax.ns
CMRdV/dtkV/s
CMRVCMV
FAULTSHIELD
SHIELD
D
R
I
V
E
R
VCC1
GND1
RESET
VIN+VIN
2
3
4
5
1
13
10
14
9,12
16
15
DESAT
UVLO
LED1
LED2
11
FAULT6
7 8
VLED1+
VLED1 V
CC2VC
VOUT
VEE
VE
VLED2+
DESTAT
Desat,UVLO,FaultFeedback
ACPL-38JT SO16 5000 1230 -40 to 125 15 to30
Buered 2.5 1.5 500 500 300 350 15 1500
VCC
VO
N/C
Anode
Cathode
N/C
VO
VEE
8
7
6
5
1
2
3
4
UVLO ACPL-312T DIP8 3750 630 -40 to 125 15 to30 7 to 16 2.5 5 500 500 300 350 15 1500
Note: ^ - Advanced information, may subject to changes.
Automotive 1MBd Transistor Output Optocoupler
Device Part No. Package VISOVRMS
VIORMV
peak
OperatingTemperature
C
VCCV
ILEDmA
CTRMin.
%
CTRTyp.
%
tPHLMax.
s
tPHLMax.
s
PWDMax.
s
tPSKMax.
s
CMRdV/dt
kV/s
CMRVCM
VSingle Channel
no e
atho e
C6
5
4
1
ACPL-M46T SO5 4000 560 -40 to 125 4.5 to 30 10 to 20 44 90 0.55 0.55 0.45 0.45 15 1500
6
5
4
1
3
ACPL-M43T SO5 4000 560 -40 to 125 20 5 to 15 20 45 1 1 0.45 0.5 15 1500
ACPL-K43T^ SSO8 5000 1 140 - 40 to 1 25 20 5 to 15 24 65 1 1 0.45 0.5 15 1500
ACPL-M49T SO6 4000 560 -40 to 125 20 4 to 10 20 58 100 100 0.45 0.5 15 1500
ACPL-K49T^ SSO8 5000 1 140 - 40 to 1 25 20 4 to 10 24 58 100 100 0.45 0.5 15 1500
ACPL-K23T^ SSO8 5000 1 140 - 40 to 1 25 20 0.8 to 10 19 130 20 20 15 1500
Dual Channel
1
2
3
4
8
7
6
5
Anode1
Anode2
Cathode1
Cathode2
VCC
VD1
VD2
GND
ACPL-K44T^ SSO8 5000 1 140 - 40 to 1 25 20 5 to 15 20 65 1 1 0.45 0.5 15 1500
ACPL-K24T^ SSO8 5000 1 140 - 40 to 1 25 20 0.8 to 10 19 130 20 20 15 1500
8/13/2019 Optical Sensor Product Guide-Lr
23/60
23
Optoisolation and Optical Sensor Products
Extended Temperature R2Coupler
Device Part No. Pack-age
OperatingTemperatureC
IOUTA(MAX)
IFmA
CTR tPLHs
Max.
tPHLs
Max.
PWD
ns
Max.
tPSKns
Max.
CMR - V/s@VCM VISOVRMSMin.
VIORMV
peak%Min.
%Max.
CMRV/s(Min.)
VCMV
ACPL-M43U-000E SO5 -40 to 125 NA 10 32 80 1.0 1.0 850 NA 15000 1500 3750 567
ACPL-M46U-000E SO5 -40 to 125 NA 10 44 90 0.4 0.6 450.0 NA 15000 1500 3750 567
ACPL-M61U-000E S05 -40 to 125 NA 5 NA NA 0.1 0.1 35 40 15000 1000 3750 567
ACPL-312U-000E DIP6 -40 to 125 2.5 7 N/A N/A 0.5 0.5 300 350(PDD)
25000 1500 3750 630NEW
NEW
NEW
NEW6
5
4
1
3
no e
a t o e
CC
GND
1
3 SHIELD
ATHODE
ANODE V C
GND
VO
6
5
4
VCC
VO
N/C
Anode
Cathode
N/C
VO
VEE
8
7
6
5
1
2
3
4
Automotive Miniature Analog Isolation Amplifier
Device Features Part No. Package VISOVRMS
VIORMV
peak
OperatingTemperature
C
VDDV
InputRange
Typ.V
GainTyp.
V/V
GainTol
Max.%
NonLMax.
%
Off-set
Max.mV
BWTyp.
kHz
CMRdV/dt
kV/s
CMRVCM
V
1
2
3
4
8
7
5
IDD1VDD1
IN+II
VINII
ND1
IDD2VDD2
V UT+
V UT
ND2
+
SHIELD
2% GainAccuracy
ACPL-782T DIP8 4000 891 -40 to 125 4.5 to5.5
0.2 8 2 0.35 4 100 10 1000
1
2
3
4
8
7
6
5
VDD1
VIN
SD
GND1
VDD2
VOP
VON
GND2SHIELD
DC VoltageSensing,Shut-downControl
ACPL-C87AT^ SSO8 5000 1140 -40 to 125 4.5 to5.5
0 to 2 1 1 0.3 100 10 1000
ACPL- C87BT^ SSO8 5000 1140 -40 to 125 4.5 to5.5
0 to 2 1 0.5 0.3 100 10 1000
Note: ^ - Advanced information, may subject to changes.
8/13/2019 Optical Sensor Product Guide-Lr
24/60
24
Optoisolation and Optical Sensor Products
ri ge + erial ata ut
-
HCPL-902J
-
Isolation
Barrier
erial Data In
Data Clock
Chip Select
r i g e
o
DescriptionThe ACML-74xx series of CMOS digital iso-
lators utilizes magnetic coupling throughthick insulation to provide high speed, high
insulation performance yet consuming lowpower at high data rates.
The HCPL-90xx/-09xx series CMOS digitalisolators integrated with giant magneto-resistive (GMR) technology enable high
speed performance and excellent transientimmunity specifications.
All devices operate at 3.3 V or 5 V supplyvoltages, boasting low power consumption.
They are able to withstand high common
mode voltages, 25kV/s at Vcm=1000V, and
meet UL 1577 and IEC 60950-1, IEC 61010-1
and IEC 60601-1 safety ratings.
Benefits
High insulation: UL1577 (5.6kVrms 1 minrating) and IEC 60950-1 and IEC 61010-1working voltage (up to 1132Vpeak)
High speed (100MBd), low PWD (3ns)and low Tp (18ns)
Wide temperature operation
(-40C to 105C)
Buer input and CMOS output(eliminate input/output resistors)
Multi-channel (1, 2 & 4-ch)
Low power consumption
Typical IsolatedA/D ConversionBlock Diagram
Digital Isolator
Digital Isolator ACML-74XX, HCPL-09XX AND HCPL-90XX Product Selection
Device Part No. Channel Package Max .Data Rate
MBd
Min.
tPLH& tPHL(VCC=5.0V)
ns
Max.
tPLH& tPHL(VCC=3.3V)
ns
Max.
PWDnsMax.
tPSKnsMax.
CMR - V/s@VCM VISOVRMSMin.
CMRV/s(Min.)
VCMV
HCPL-0900 Single SO8 100 15 18 3 6 15000 1000 2500
HCPL-9000 Single 300 mil DIP8 100 15 18 3 6 15000 1000 2500
HCPL-0930 Dual SO8 100 15 18 3 6 15000 1000 2500
HCPL-9030 Dual 300 mil DIP8 100 15 18 3 6 15000 1000 2500
HCPL-0931 Dual, Bi-Dir SO8 100 15 18 3 6 15000 1000 2500
HCPL-9031 Dual, Bi-Dir 300 mil DIP8 100 15 18 3 6 15000 1000 2500
ACML-7400 Quad SO16 Wide Body 100 32 36 2 5 25000 1000 5600
HCPL-090J Quad SO16 Narrow Body 100 15 18 3 6 15000 1000 2500HCPL-900J Quad SO16 Wide Body 100 15 18 3 6 15000 1000 2500
ACML-7420 Quad, 2/2, Bi-dir SO16 Wide Body 100 32 36 2 5 25000 1000 5600
HCPL-091J Quad, 2/2 Bi-dir SO16 Narrow Body 100 15 18 3 6 15000 1000 2500
HCPL-901J Quad, 2/2 Bi-dir SO16 Wide Body 100 15 18 3 6 15000 1000 2500
ACML-7410 Quad, 3/1, Bi-dir SO16 Wide Body 100 32 36 2 5 25000 1000 5600
HCPL-092J Quad, 3/1 Bi-dir SO16 Narrow Body 100 15 18 3 6 15000 1000 2500
HCPL-902J Quad, 3/1 Bi-dir SO16 Wide Body 100 15 18 3 6 15000 1000 2500
DD1
I
NC
2
U
VDD2
V E
8
63
4GalvanicIsolation
V
I
I
GND
U
V
U
alvanic
solation
4
12
13
4
16VDD1
3
4
1 GND
U 4
U
U 2
OUT
V
Ga
lvanicIsolation
3
4
6 11
14
V
IN
IN
U
U 4
2
I 4
I
U 2
U
V
alvanicIsolation
1
2
4
5
14
V
GND
I
I 2
IN
U 4
GND 2
IN
U 3
U
U
GND
V
GalvanicIsolation
I
U
GND
I 2
OUT7
54GalvanicIsolation
NEW
NEW
NEW
Applications
Digital eldbus isolation
Multiplexed datatransmission
Computer peripheralinterface
High speed digital systems
Isolated data interfaces
Logic level shifting
8/13/2019 Optical Sensor Product Guide-Lr
25/60
25
Optoisolation and Optical Sensor Products
DSP
SOLAR PANEL
CHARGE CONTROLLER /
DC-DC CONVERTERINVERTER DC-AC
GATE
DRIVERS
CURRENT
SENSOR
ACPL-C79B/
C79A/C790
CURRENT
SENSOR
VOLTAGE
SENSOR
GATE DRIVER
ACPL-H342/K342
GATE DRIVERS
ACPL-H342/K342, 4X
VOLTAGE SENSOR
ACPL-C79B/C79A/C790
TO
POWER
GRID
PWM PWM
HV
HV+
ACPL-M61L,
2X
FIELD BUS COMMUNICATION
DescriptionThe ACPL-C79B/C79A/C790 isolation
amplifiers were designed for currentand voltage sensing in electronic power
converters in applications including motordrives and renewable energy systems.
Based on sigma-delta analog-to-digitalconverters, the new isolation amplifiers
feature high gain accuracy, low temperaturedrift of -50ppm/C, 3.3V/5V output supply
operation and a wide -40 to +105C
operating temperature range. Thesefeatures are delivered in a SSO-8 packagethat has a footprint 30% smaller than thestandard DIP-8 package. When mounted on
a PCB, it occupies a space that is a fractionof that for a traditional Hall Effect current
transducer.
The series is implemented with a fullydifferential circuit with gain accuracy of
0.5% (ACPL-C79B), 1% (ACPL-C79A), and3% (ACPL-C790). With a 200kHz bandwidth
and 1.6s response time, the ACPL-C79xcaptures transients during short circuitand overload conditions. Operating from
a single 5V supply, the isolation amplifierseries features an excellent nonlinearity of
0.05% and a SNR of 60dB.
Miniature Analog Isolation Amplifier
Example Application: Block diagram of a micro-inverterwith simplified DC-DC-AC topology.
Benefits
Compact packagesuitable for high volumeproduction process
Cost-eective solution
Reinforced insulation
Applications
Motor phase and railcurrent sensing
Data acquisition systems
Inverter current sensing
General purpose currentsensing and monitoring
8/13/2019 Optical Sensor Product Guide-Lr
26/60
26
Optoisolation and Optical Sensor Products
Isolated Sigma-Delta Modulator
Device Part No. Package OperatingTemperatureC
Gain Errorat 25C% Max.
INLLSBTyp.
ENOBBitsTyp.
VDD2V
CMR - V/s@VCM ClockMHzTyp.
VISOVRMSMin.
VIORMVpeakCMR
V/s(Typ.)
VCMV
VDD2
GND2
NC
MCLKIN
GND2
NC
MDAT
VIN
VDD1
VIN+
MOD.
DATA
OUT
CLK
DET.
CLK
IN
GND1
NC
GND1
VDD1
NC
NC
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
L
ACPL-796J-000E SO16 -40 to +105 1 3 12 3 - 5.5 25000 1000 5 - 20,External
5000 1230*
211
NCNC
NCDAT
0NC C
9GND1 ND2
6
15
DD1
VIN+
GND2
C
14VIN VDD2
4 3NC CLKSIGMA-DELTAMOD./
HCPL-786J SO16 -40 to +85 2 3 11 4.5 - 5.5 20000 1000 10, Internal 5000 1230
1
2
4
8
7
6
VDD1
IN+
V N
DD2
MCLK
MDAT
GND2SHIELD
ISOLATION
DECODE
-T
.
ACPL-C797-000E Stretched SO8 -40 to +105 1 3 12 3 - 5.5 25000 1000 10, Internal 5000 1230
ACPL-7970 DIP8 -40 to +105 1 3 12 3 - 5.5 25000 1000 10, Internal 5000 891
HCPL-7860 DIP8 -40 to +85 1 (Matching) 3 11 4.5 - 5.5 20000 1000 10, Internal 3750 891
HCPL-7560 DIP8 -40 to +85 5 64 8 4.5 - 5.5 20000 1000 10, Internal 3750 891*
1
11
A 1
MCLK2 THR1
CO -
VERSION
INTER-
FACE
C O G .
INTER-
FACE
0MDAT2 1
9GND RESET
1 1
1A A
4CDAT SCLK
41 A
C 1
C
-
HOLD
C
&
HCPL-0872 SO16 -40 to +85 Dual, Programmable Digital Filterwith SPI Interface
4.5 - 5.5 NA NA ModulatorClock
NA NA
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information, may subject to changes, - VDD
NEW
NEW
Miniature Isolation Amplifier
Device Part No. Package OperatingTemperature
C
Gain Errorat 25C
% Max.
Non-linearity
% Typ.
Band-width
kHz Typ.
VDD2V
CMR - V/s@VCM OutputConfigura-
tion
VISOVRMS
Min.
VIORMV
peakCMRV/s(Typ.)
VCMV
1
2 7
DD1V D1
VN+
IN
GND1
IDD2VDD2
VOUT+
VOUT
ND2SHIELD
ACPL-C78A-000E Stretched SO8 -40 to +85 1 0.0037 100 4.5 - 5.5 15000 1000 Differential 5000 1230*
ACPL-C780-000E Stretched SO8 -40 to +85 3 0.0037 100 4.5 - 5.5 15000 1000 Differential 5000 1230*
ACPL-C784-000E Stretched SO8 -40 to +85 5 0.0037 100 4.5 - 5.5 15000 1000 Differential 5000 1230*
ACPL-782T-000E R2Coupler DIP8 -40 to +125 2 0.0037 100 4.5 - 5.5 15000 1000 Differential 3750 891
ACPL-C79B-000E Stretched SO8 -40 to +105 0.5 0.05 200 3 - 5.5 15000 1000 Differential 5000 1230
ACPL-C79A-000E Stretched SO8 -40 to +105 1 0.05 200 3 - 5.5 15000 1000 Differential 5000 1230
ACPL-C790-000E Stretched SO8 -40 to +105 3 0.05 200 3 - 5.5 15000 1000 Differential 5000 1230
ACPL-790B DIP8 -40 to +105 0.5 0.05 200 3 - 5.5 15000 1000 Differential 5000 891
ACPL-790A DIP8 -40 to +105 1 0.05 200 3 - 5.5 15000 1000 Differential 5000 891
ACPL-7900 DIP8 -40 to +105 3 0.05 200 3 - 5.5 15000 1000 Differential 5000 891
HCPL-7800A DIP8 -40 to +85 1 0.0037 100 4.5 - 5.5 15000 1000 Differential 3750 891
HCPL-7800 DIP8 -40 to +85 3 0.0037 100 4.5 - 5.5 15000 1000 Differential 3750 891
HCPL-7840 DIP8 -40 to +85 5 0.0037 100 4.5 - 5.5 15000 1000 Differential 3750 891*
VIN+
V - 23
5
7
8
15
14
12
10
9
CHCL
VDD1
VDD1 DD2
DD2
REF
VOUT
BSVAL
AULT
ND ND
ND
VLED+
HCPL-788J SO16 -40 to +85 3 0.06 30 4.5 - 5.5 25000 1000 Single-ended 5000 1230
ACPL-785J-000E SO16 -40 to +85 5 0.06 30 4.5 - 5.5 25000 1000 Single-ended 5000 1230*
1
2
3
4
8
7
6
I D1D1
VN+
IN
I D2VDD2
VOUT
VREF
+
SHIELD
HCPL-7510 DIP8 -40 to +85 3 0.06 100 4.5 - 5.5 15000 1000 Single-ended 3750 891*
HCPL-7520 DIP8 -40 to +85 5 0.06 100 4.5 - 5.5 15000 1000 Single-ended 3750 891*
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information.
NEW
NEW
NEW
NEW
NEW
NEW
8/13/2019 Optical Sensor Product Guide-Lr
27/60
27
Optoisolation and Optical Sensor Products
Integrated Gate Drive Optocoupler
DescriptionIn typical motor drive and renewable
energy power conversion systems, there areseveral signals between the power devices
and the micro-controller that need isolationand additional customized functionssuch as gate drive and current/voltage
sensing. Avago Technologiesgate drive andisolation amplifier products provide low
cost, high performance solutions for suchapplications.
High performance motor drives require
precision timing for turning on and offthe power devices on the inverter whilerenewable energy inverter needs to bereliable and e cient when converting DC-
link voltage to usable AC power output. Themicrocontroller that controls these functions
needs to be isolated from the high voltageinverter side. Avago Technologies offers
a variety of optocouplers that have built-in gate drive capability. These gate driveoptocouplers come in wide range of output
current from 0.4A to 5A, and selected parts
with integrated protection features such asActive Miller Clamp, under voltage lockout,
fault Status feedback and desaturationdetection. For solutions that require lower
output power capability, IPM interfaceoptocouplers will meet the need.
Benefits
Rail-to-rail output voltage for reliableIGBTs drive
Integrated fault protection and feedbackto reduce component count and solutioncost
Short propagation delay for fasterswitching
Fast IGBT switching for improvede ciency
Low power consumption for bootstrapoperation
High common mode transient rejectionensures reliable operation under noisyenvironment
Direct drive of high power IGBTs
Reinforced insulation
Typical Motor Drive Block Diagram
Applications
Isolated IGBT/MOSFETgate drive
AC and brushless DCmotor drives
Renewable energy
inverters Industrial inverters
Switching power supplies
Uninterruptible powersupplies (UPS)
MICRO CONTROLLER
RECTIFIER
AC-DC
CHARGE CONTROLLER /
DC-DC CONVERTERINVERTER DC-AC
M
R
S
T
CURRENT SENSOR
ACPL-C79B/C79A/C790
CURRENT
SENSOR, 3X
VOLTAGE
SENSOR
GATE DRIVE
ACPL-332J
GATE DRIVE
ACPL-332J
VOLTAGE SENSOR
ACPL-C79B/C79A/C790
8/13/2019 Optical Sensor Product Guide-Lr
28/60
28
Optoisolation and Optical Sensor Products
Integrated Gate Drive Optocoupler Product Selection
Device Part No. Package IF(on)mA
Min.
lOUTA
Min.
lOUTA
Max.
tPLHs
Max.
tPHLs
Max.
PDDs
Max.
VCCV
Max.
CMR - V/s@VCM VISOVRMS
Min.
VIORMV
peak
CMR
V/s (Min.)
VCM
V
Single Channel
VCC
VOUT
N/C
VEE
1
2
3
4
8
7
6
5
CATHODE
ANODE
N/C
N/C
ACNW3430-000E^ 400 mil DIP 7 3.0 4.0 0.35 0.35 0.2 30 40000 1500 5000 1414
VCC6
VOUT5
VEE4
2N/C
1ANODE
4CATHODE
ACPL-P343-000E Stretched SO6 7 3.0 4.0 0.20 0.20 0.1 30 35000 1500 3750 891*
ACPL-W343-000E Stretched SO6 7 3.0 4.0 0.20 0.20 0.1 30 35000 1500 5000 1140*
ACPL-P341-000E Stretched SO6 7 2.5 3.0 0.20 0.20 0.1 30 35000 1500 3750 891*
ACPL-W341-000E Stretched SO6 7 2.5 3.0 0.20 0.20 0.1 30 35000 1500 5000 1140*
ACPL-P340-000E Stretched SO6 7 0.8 1.0 0.20 0.20 0.1 30 35000 1500 3750 891*
ACPL-W340-000E Stretched SO6 7 0.8 1.0 0.20 0.20 0.1 30 35000 1500 5000 1140*
VCC
VOUT
VCLAMP
VEE
1
2
3
4
8
7
6
5
CATHODE
NC
ANODE
NC
VCLAMP
ACPL-H342-000E Stretched SO8 7 2.0 2.5 0.35 0.25 -0.2 30 40000 1500 3750 891*
ACPL-K342-000E Stretched SO8 7 2.0 2.5 0.35 0.25 -0.2 30 40000 1500 5000 1140*
VCC
VO
N/C
Anode
Cathode
N/C
VO
VEE
8
7
6
5
1
2
3
4
ACPL-312U-000E 300 mil DIP 7 2.0 2.5 0.5 0.5 0.35 30 25000 1500 3750 630
SHIELD
SHIELD
D
R
I
V
E
R
VE
DESAT
VCC2
VOUT
VCLAMP
VEE
VCC1
VS
FAULT
ANODE
CATHODE
VCLAMP
VLED
6,7
5,8
2
3
1,4
13
11
14
9,12
10
16
15
DESAT
UVLO
LED1
LED2
ACPL-330J-000EACPL-331J-000E
SO16 8 1.0 1.5 0.25 0.25 0.35 30 15000 1500 5000 1230
1.5A Highly Integrated Gate Drive Optocoupler with Active Miller Clamp, Over-Current Protection and Fault Feedback Under Voltage Lock-Out Protection (UVLO) with Hysteresis
Automatic Fault Reset after xed delay time (for ACPL-330J-000E only)
ACPL-332J-000EACPL-333J-000E
SO16 8 2.0 2.5 0.25 0.25 0.35 30 15000 1500 5000 1230
2.5A Highly Integrated Gate Drive Optocoupler with Active Miller Clamp, Over-Current Protection and Fault Feedback Under Voltage Lock-Out Protection (UVLO) with Hysteresis Automatic Fault Reset after xed delay time (for ACPL-333J-000E only).
1
3
2
4
8
6
7
5
ACPL-H312-000E Stretched SO8 7 2.0 2.5 0.5 0.5 0.35 30 15000 1500 3750 891*
ACPL-K312-000E Stretched SO8 7 2.0 2.5 0.5 0.5 0.35 30 15000 1500 5000 1140*
61
52
43
ANODE
N.C.
CATHODE
VCC
VO
VEESHIELD
ACPL-P302-000E Stretched SO6 7 0.2 0.4 0.7 0.7 0.5 30 10000 1000 3750 891*
ACPL-P314-000E Stretched SO6 8 0.4 0.6 0.7 0.7 0.5 30 25000 1000 3750 891*
ACPL-W302-000E Stretched SO6 7 0.2 0.4 0.7 0.7 0.5 30 10000 1000 5000 1140*
ACPL-W314-000E Stretched SO6 8 0.4 0.6 0.7 0.7 0.5 30 25000 1000 5000 1140*
VO
VEE
1
3
2
4
8
6
7
5SHIELD
CATHODE
ANODE
N/C
N/C VCC
VEE
ACNW3190-000E 400 mil DIP8 10 4.0 5.0 0.5 0.5 0.3 30 15000 1500 5000 1414
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
8/13/2019 Optical Sensor Product Guide-Lr
29/60
29
Optoisolation and Optical Sensor Products
Integrated Gate Drive Optocoupler Product Selection
Device Part No. Package IF(on)mA
Min.
lOUTA
Min.
lOUTA
Max.
tPLHs
Max.
tPHLs
Max.
PDDs
Max.
VCCV
Max.
CMR - V/s@VCM VISOVRMS
Min.
VIORMV
peak
CMR
V/s (Min.)
VCMV
1
3
SHIELD
2
4
8
6
7
5
/C
CATHODE
ANODE
/C
V C
V
N/C
V E
ACNW3130-000E 400 mil DIP8 10 2.0 2.5 0.5 0.5 0.35 30 40000 1500 5000 1414
ACPL-3130-000E 300 mil DIP8 7 2.02.5
0.5 0.5 0.35 30 40000 1500 3750 630*
ACPL-J313-000E 300 mil DIP8 7 2.02.5
0.5 0.5 0.35 30 40000 1500 3750 1230^
ACPL-T350-000E 300 mil DIP8 7 2.02.5
0.5 0.5 0.35 30 15000 1500 3750 630*
HCNW3120 400 mil DIP8 10 2.02.5
0.5 0.5 0.3 30 25000 1500 5000 1414
HCPL-J312 300 mil DIP8 7 2.02.5
0.5 0.5 0.35 30 25000 1500 3750 1230^
HCPL-J314 300 mil DIP8 8 0.40.6
0.7 0.7 0.5 30 25000 1500 3750 891
HCPL-T250 300 mil DIP8 7 0.5 1.5 0.5 0.5 30 5000 600 3750 630*
HCPL-T251 300 mil DIP8 8 0.1 0.4 1.0 1.0 30 10000 600 3750
HCPL-0302 SO8 7 0.2 0.4 0.7 0.7 0.5 30 10000 1000 3750 566*
HCPL-0314 SO8 8 0.4 0.6 0.7 0.7 0.5 30 25000 1000 3750 566*
HCPL-3020 300 mil DIP8 7 0.2 0.4 0.7 0.7 0.5 30 10000 1000 3750 630*
HCPL-3120 300 mil DIP8 7 2.0 2.5 0.5 0.5 0.35 30 25000 1500 3750 630*
HCPL-3140 300 mil DIP8 8 0.4 0.6 0.7 0.7 0.5 30 25000 1000 3750 630*
HCPL-3150 300 mil DIP8 7 0.5 0.6 0.5 0.5 0.35 30 15000 1500 3750 630*
HCPL-3180 300 mil DIP8 10 2.0 2.5 0.2 0.2 0.09 20 10000 1500 3750 630*
6
5
4
13
2
1
0
12
3
4
6
7
8
VEVLED2+
ESAT
VCC2
VC
VOUT
VEE
VEE
VN+VIN-
VCC1
GND1
RESET
FAULT
VLED1+
VLED1-
HCPL-316J SO16 2.0 2.5 0.5 0.5 0.3 30 15000 1500 5000 1230 2.0 A Highly Integrated Gate Drive Optocoupler with over-current Protection and Fault Feedback CMOS compatible Under Voltage Lock-Out Protection (UVLO) with Hysteresis
Dual Channel1
3SHIELD
2
8
6
4
9
/C
ATHODE
ANODE
/C
VCC
VEE
VO
VEE
7
6
0
1
ATHODE
ANODE
VO
VCC
SHIELD
HCPL-314J SO16 8 0.4 0.6 0.7 0.7 0.5 30 25000 1500 5000 1230
HCPL-315J SO16 7 0.5 0.6 0.5 0.5 0.35 30 15000 1500 5000 1230
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information, may subject to changes.
8/13/2019 Optical Sensor Product Guide-Lr
30/60
30
Optoisolation and Optical Sensor Products
Intelligent Power Module (IPM) Based Inverter Block Diagram
DescriptionThe ACNV/HCNW/HCPL-45xx and ACPL-
48xx series optocouplers are designedfor Intelligent Power Module (IPM)
drive applications such as inverters andmotor control systems. These high speedoptocouplers have high CMR performance
that helps to reject common mode noise in
such high voltage systems. The output of
HCNW/HCPL-45xx devices is conventionalopen-collector; the output of ACPL-48xx
devices came with totem pole output stage
eliminates the necessity of using the pull-upresistor and allows direct drive to the IPM.ACNV45xx devices allow very high workingvoltage for use in Renewable Energy Supply
system.
In addition to Intelligent Power Moduledrive, the ACNV/HCNW/HCPL-45xx and
ACPL-48xx series optocouplers can be usedin general purpose isolation applications
like high speed logic ground isolation,isolated line receivers, and microprocessorsystem interfaces.
Benefits
Short propagation delay for fasterswitching
Fast IGBT switching for improved
e ciency High Common Mode Transient Rejection
ensures reliable operation under noisyenvironment
Wide operating temperature range
Reinforced insulation
Intelligent Power Module Interface Optocoupler
Applications
Intelligent power module
Inverter/Motor control
Power switch design
General purpose digitalisolation
Typical Level Shifting/TTL Interface Block Diagram
SHIELD
20K
ACNV4506 +15V
NOTE: FOR BEST CMR PERFORMANCE, CONNECT PIN 6 TO PIN 7
1
2
3
5
10
9
8
6
4 7
+5V
74LS05
RIN
RINIF
VIN
IF
VOUTVOL
ILIO
5 - VF=
IO (min)= IF CTR (min)
VOL= 15 RL {IO(min) + IIL}
=15-RL {IF CTR (min) + IIL}
CURRENT SENSE
M
MCUANDPWMGENERATOR
VCC
VCC
IN_UH
GND
IPM HV
U
V
W
U V W
HV+
IN_UL
ACPL-M484/P484/W484, OR
ACPL-M483/P483/W483
FOR PHASES U, V AND W
COMMON 15V TO 20V
POWER SUPPLY
HVICGATEDRIVE
+
HVICGATEDRIVE
HVICGATEDRIVE
8/13/2019 Optical Sensor Product Guide-Lr
31/60
31
Optoisolation and Optical Sensor Products
Device Part No. Package IF(on)mA
Min.
CTR tPLHs
Max.
tPHLs
Max.
PDD
s
Max.
CMR - V/s@VCM VISOVRMSMin.
VIORMV
peak%Min. %Max. IF
mA CMRV/s (Min.) VCM
V
Single Channel ACPL-M483-000E^ SO5 4 0.10 0.10 0.10 20000 1000 3750 567*
ACPL-P483-000E^ Stretched SO6 4 0.10 0.10 0.10 20000 1000 3750 891*
ACPL-W483-000E^ Stretched SO6 4 0.10 0.10 0.10 20000 1000 5000 1140*
ACPL-M484-000E^ SO5 4 0.10 0.10 0.10 20000 1000 3750 567*
ACPL-P484-000E^ Stretched SO6 4 0.10 0.10 0.10 20000 1000 3750 891*
ACPL-W484-000E^ Stretched SO6 4 0.10 0.10 0.10 20000 1000 5000 1140*
ACNV4506-000E 500 mil DIP10 10 44 10 0.55 0.40 0.50 30000 1500 7500 2262*
7
1
2
3
4 5
6
8NC
Anode
Cathode
DNGCN
NC
SHIELD
V
V
CC
O
ACPL-4800-000E 300 mil DIP8 6 0.35 0.35 0.25 30000 1000 3750 630*
6
5
4
1
3
ACPL-M43U-000E SO5 10 32 80 10 1 1 0.9 15000 1000 3750 567*
Ano e
a t o e
CC
O
6
4
1
H L
ACPL-M46U-000E SO5 10 44 90 10 0.4 0.55 0.45 15000 1000 3750 567*
ACPL-P456-000E Stretched SO6 10 44 >90 10 0.55 0.45 0.45 15000 1500 3750 891*
ACPL-W456-000E Stretched SO6 10 44 >90 10 0.55 0.45 0.45 15000 1500 5000 1140*
ACPL-P480-000E Stretched SO6 6 0.35 0.35 0.25 20000 1000 3750 891*
ACPL-W480-000E Stretched SO6 6 0.35 0.35 0.25 20000 1000 5000 1140
ACPL-P481-000E Stretched SO6 6 0.35 0.35 0.25 20000 1000 3750 891*
ACPL-W481-000E Stretched SO6 6 0.35 0.35 0.25 20000 1000 5000 1140*
V
NC
NC
NC
Anode
Cathode
SHIELD
V
ND
8
7
54
C
ACPL-K453-000E Stretched SO8 16 19 50 16 1.00 1.00 1.00 15000 1500 5000 1140*
V
NC
Anode
Cathode
V
ND
5
4
2
3
O
HIELD
ACPL-P454-000E Stretched SO6 12 26 65 12 1.14 1.00 1.30 15000 1500 3750 891*
ACPL-W454-000E Stretched SO6 12 26 65 12 1.14 1.00 1.30 15000 1500 5000 1140*
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000VRMS/1 minute Option 020,^ - Advanced information, may subject to changes.
NEW
NEW
NEW
NEW
NEW
NEW
NEW
Intelligent Power Module Interface Optocoupler Product Selection
8/13/2019 Optical Sensor Product Guide-Lr
32/60
32
Optoisolation and Optical Sensor Products
Device Part No. Package IF(on)mA
Min.
CTR tPLHs
Max.
tPHLs
Max.
PDD
s
Max.
CMR - V/s@VCM VISOVRMSMin.
VIORMV
peak%Min. %Max. IF
mA CMRV/s (Min.) VCM
V
V
NCnode
athode V
GND
1
4
O
HCNW4502 400 mil DIP8 16 19 50 16 1.0 1.0 1000 10 5000 1414
HCNW4503 400 mil DIP8 16 19 50 16 1.0 1.0 15000 1500 5000 1414
HCNW4504 400 mil DIP8 12 25 65 12 1.4 1.0 1.3 15000 1500 5000 1414
HCPL-0452 SO8 16 19 50 16 1.0 1.0 1000 10 3750 560*
HCPL-0453 SO8 16 19 50 16 1.0 1.0 1.0 15000 1500 3750 560*
HCPL-0454 SO8 12 26 65 12 1.4 1.0 15000 1500 3750 560*
HCPL-4502 300 mil DIP8 16 19 50 16 1.0 1.0 1000 10 3750/5000 # 630*
HCPL-4503 300 mil DIP8 16 19 50 16 1.0 1.0 1.0 15000 1500 3750/5000 # 630*
HCPL-4504 300 mil DIP8 12 26 65 12 1.4 1.0 1.3 15000 1500 3750/5000 # 630*
HCPL-J454 300 mil DIP8 12 21 65 12 0.7 0.5 1.3 15000 1500 3750 891
V C
V
NC
NC
Cathode
Anode
V
GND
8
72
3
SHI L
k W
HCNW4506 400 mil DIP8 10 44 >90 10 0.55 0.40 15000 1500 5000 1414
HCPL-0466 SO8 10 44 >90 10 0.55 0.48 0.45 15000 1500 3750 560*
HCPL-4506 300 mi l DIP8 10 44 >90 10 0.55 0.40 0.45 15000 1500 3750/5000 # 630*
HCPL-J456 300 mi l DIP8 10 44 >90 10 0.55 0.40 0.45 15000 1500 3750 891
VAnode
Cathode
V
GND4
O
SHIELD
HCPL-M452 SO5 16 20 50 16 1.0 1.0 1000 10 3750 567*
HCPL-M453 SO5 16 20 50 16 1.0 1.0 1.0 15000 1500 3750 567*
HCPL-M454 SO5 12 26 65 12 1.4 1.0 1.3 15000 1500 3750 560*
Anode
athode
VCC
VO
GND
5
4
1
SHI L
HCPL-M456 SO5 10 44 >90 10 0.55 0.40 0.45 15000 1500 3750 560*
Dual Channel
V
V01
node1
Cathode
Cathode 2
node
V
ND
2
3
HCPL-0534 SO8 16 19 50 16 1.0 1.0 15000 1500 3750 560*
HCPL-4534 300 mil DIP8 16 19 50 16 1.0 1.0 15000 1500 3750/5000 # 630*
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000VRMS/1 minute Option 020,^ - Advanced information, may subject to changes.
Intelligent Power Module Interface Optocoupler Product Selection
8/13/2019 Optical Sensor Product Guide-Lr
33/60
33
Optoisolation and Optical Sensor Products
DescriptionThe HCPL-2602/12 have input current
regulators and integrated high gain photodetectors. The input regulator serves as a
line terminator for line receiver applications.The higher LED threshold voltage providesimproved immunity to differential noise and
the rejection internally shielded detector
provides better common-mode rejection
with no sacrifice in speed.
The diagram below illustrates an unbalanced
line receiver using the integrated voltage-
clamp input optocoupler, HCPL-2602.TTL data is converted to a differentialsignal viathe differential line driver, andtransmitted over twisted-pair wire. The
Schottky diode helps to improve the turn-on and turn-off delays.
Benefits Line termination included no extra
circuitry required
Isolated Line Receiver
Typical Block Diagram
8
7
6
5
.01.0F
390
15 pF
R
1
2
3
4HCPL-2602/12
HABT-5400
1
2
4
3
BELDEN 8777
l
VCC
GND
5
6
7
16
+5V
8
1/2 9614
VO
+5V
VN
Line Receiver Product Selection
Device Part No. Package Output Collector OutputmA Max.
tPLHsMax.
tPHLsMax.
CMR - V/s@VCM VISOVRMSMin.CMR
V/s (Min.)VCMV
HCPL-2602 300 mil DIP8 50 100 100 1000 50 3750
HCPL-2612 300 mil DIP8 50 100 100 3500 300 3750
40 ns max propagation delay skew (part to part)Line termination circuitry included
1
2
3
4
8
7
6
5
IN
IN+
GND
V
VCC
O
VE
NC
CATHODESHIELD
Applications
Isolated line receiver
Computer-peripheralinterface
Microprocessor systeminterface
Digital isolation for A/D,D/A conversion
Current sensing
Instrument Input/Outputisolation
Ground loop elimination
Pulse transformerreplacement
Power transistor isolationin motor drives
8/13/2019 Optical Sensor Product Guide-Lr
34/60
34
Optoisolation and Optical Sensor Products
20 mA Current Loop Transmitter/Receiver Product Selection
Device Part No. Package Data Rate
kBd @ (meters)
tPLHsMax.
tPHLsMax.
CMR - V/s@VCM VISOVRMSMin.CMR
V/s (Min.)VCMV
Transmitter HCPL-4100 300 mil DIP8 20 (400) 1.6 1.0 1000 50 3750
CMOS compatible data input for HCPL-4100
Receiver HCPL-4200 300 mil DIP8 20 (1400) 1.6 1.0 1000 50 3750
CMOS compatible data input for HCPL-4200
VNC
NC
C
C
C
+
-
V
ND
8
7
6
5
1
2
3
4
VCC
VO
I+
I-
VE
GND
8
7
6
5
1
DescriptionData transmission between electronic
equipment which are physically separatedby a distance of more than a few feet
can be achieved by using the HCPL-4100 (transmitter) and the HCPL-4200(receiver) optocouplers. These devices
include specialized circuits for 20 mAdigital current loop applications, and are
designed to easily interface TTL and CMOSlogic systems to current loop systems.
20 mA current loop systems conventionally
signal a logic high state by transmitting20 mA of loop current, and signal a logic low
state by allowing no more than few milli-amperes of loop current. Optical coupling
loops break ground loops and provide
very high immunity to common mode
interference. These devices are simple to use
in a data transmission system for industrialapplications and maintainintegrity.
Benefits
Direct control of the 20 mA current loop
High noise immunity
Isolated 20 mA Current Loop Transmitter/Receiver
Typical Block Diagram
Applications
Isolated 20 mA currentloop transmitter in:
Industrial controlequipment
Computer peripherals
Data communicationsequipment
GND
SHIELD
V
IE
VO
IO
7
5
62
VI
1I +
I -
I
8 V
ICC
HCPL-4100 Transmitter
IO
I
VO
IO
I
+
SHIELD 4
3
CC
GND
ICC
VI
5
I
8/13/2019 Optical Sensor Product Guide-Lr
35/60
35
Optoisolation and Optical Sensor Products
DescriptionIn the implementation of an interface from
an electrically noisy environment into logicsystems, it is often desirable to establish
some current or voltage switching pointor input switching threshold the HCPL-
3700 optocoupler provides such a solution.
This device combines an AC or DC voltageand/or current detection function with
high sensing input buffer ICs which permitcontrol of threshold levels over a wide range
like sensing industrial control systems, and
ring detection in telephone system micro-processor interfacing.
The HCPL-0370/3700/3760 threshold-sens-ing optocoupler can be used for sensing the
AC/DC power on/off condition. At the
Isolated Voltage/Current Detector
Typical Block Diagram
Isolated Voltage/Current Detector
Device Part No. Package Input Threshold Current HysteresismAtyp
tPLHsMax.
tPHLsMax.
CMR - V/s@VCM VISOVRMSMin.
VIORMVPEAK
mA CMRV/s (Min.)
VCMVMin. Max.
ACPL-K370-000E Stretched SO8 1.96 3.11 1.2 40 15 600 140 3750/5000# 1140*
ACPL-K376-000E Stretched SO8 0.87 1.56 0.6 40 15 600 140 3750/5000# 1140*
HCPL-0370 SO8 1.96 3.11 1.2 40 15 600 140 3750 567*
HCPL-3700 300 mil DIP8 1.96 3.11 1.2 40 15 600 140 3750 630*
HCPL-3760 300 mil DIP8 0.87 1.56 0.6 40 15 600 140 3750 630*
Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, #- with UL 5000VRMS/1 minute Option 020, ^- Advanced information, may subject to changes.
A
+
-
A
Applications
Limit switch sensing
AC/DC voltage andcurrent detector
Relay contact monitor
Relay coil voltage monitor
User congurablevoltage/current limitdetection
Microprocessorinterfacing
L
R /2
K
AC INPUT CONFIGURATION
L
AC
+
-
AC
V
GND
DC UP TO
1140 V
I
GND
DC+
INPUT
I
DC INPUT
I
8
DC+
DC- V
I I I
I
optocoupler input, only a pair of seriesresistors RX/2 are required to limit the
current. The AC signal can be filteredwith a capacitor at either the input or the
output of the optocoupler. The value of RXdetermines the threshold sensing voltage.
HCPL-0370/3700/3760s low threshold
current reduces power dissipation and itsbuilt-in diode bridge and hysteresis circuit
reduces the number of external compo-nents used.
Benefits Low threshold current reduces power
dissipation
Hysterisis circuit reduces externalcomponents and PCB size
8/13/2019 Optical Sensor Product Guide-Lr
36/60
8/13/2019 Optical Sensor Product Guide-Lr
37/60
37
Optoisolation and Optical Sensor Products
DescriptionThe HCPL-4562 and HCNW 4562 are
recommended for very high bandwidth(up to 15 MHz) AC analog designs such as
coupling audio or video signals.
This circuit, with the HCPL-4562 wideband
analog/video optocoupler, is optimized forvideo signal coupling. The peaked responseof the detector circuit helps extend the
frequency range over which the gain isrelatively constant. The number of gain
stages, the overall circuit topology, and the
DC bias point are all chosen to maximizethe bandwidth.
HCPL-4562 provides simple and cost effec-tive solutions for coupling audio and video
signals.
Benefits
Optimized for video signal coupling
Simple design for audio and videocoupling
Cost eective
Reinforced insulation
Wideband Analog/Video Optocoupler
Typical Block Diagram
8
7
6
5
2CC1
2
3
4
V
OUT
HIGHIMPEDANCELOAD
Q Q = 2N39041 4
Q4
Q3
R9
750R6
9.1 K
R11
470
2
R8
1.0 K
R10
100
22
R7
15 K
Q2
R2
1.0 K
R1
6.8 K
1N4150
D1
500
51
R3
100
C1
47 F
Q1
VE
R4
= POTENTIOMETER+51RESISTOR
1CCV
IN
GV= VOUT/VIN
Wideband Analog/Video Optocoupler Product Selection
Device Part No. Package BandwidthMHztyp
DC Non-Linearity%Max.
CTR%typ
IMRRdBtyp
VISOVRMSMin.
VIORMVpeak
HCNW4562 400 mil DIP8 9 0.15 52 119 5000 1414
HCPL-4562 300 mil DIP8 17 0.25 45 122 3750/5000# 630*
0.3% / C gain temperature coecient
Notes:
* - with IEC/EN/DIN EN 60747-5-2/5 Option 060
# - with UL 5000V RMS /1 minute Option 020
7
1
2
3
4 5
6
8NC
ANODE
CATHODE
NC
VCC
VB
VO
GND
Applications
Video isolation for thefollowing standards/formats:
NTSC, PAL, SECAM, S-VHS,ANALOG RGB
Low drive currentfeedback
Element in switchingpower supplies:ISDN networks
A/D converter signalisolation
Analog signal groundisolation
High voltage insulation
8/13/2019 Optical Sensor Product Guide-Lr
38/60
8/13/2019 Optical Sensor Product Guide-Lr
39/60
39
Optoisolation and Optical Sensor Products
General Purpose Phototransistor Optocoupler DC Input Product Selection
Device Part No. Package Absolute
Max. IFmA
CTR VCE(sat) tr/tfstyp
BVCEOVMin.
VF VISOVRMSMin.
Note
%Min.
%Max.
IFmA
VCEV
VMax.
IFmA
ICmA
VMax.
IFmA
Single Channel-4 pin ACPL-217-500E
(Half pitch)
SO4 50 50 600 5 5 0.4 8 2.4 2/3 80 1.4 20 3000 1
HCPL-181-000E# SO4 50 50 600 5 5 0.2 20 1 4/3 80 1.4 20 3750 1
HCPL-817-000E* 300 mil DIP4 50 50 600 5 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3
Single Channel-6 pin 4N25-000E 300 mil DIP6 80 20 10 10 0.5 50 2 3/3 30 1.5 10 2500 1/2/3
4N35-000E 300 mil DIP6 60 100 10 10 0.3 50 2 3/3 30 1.5 10 3550 1/2/3
CNY17-1-000E 300 mil DIP6 60 40 80 10 5 0.3 10 2.5 5/5 70 1.7 60 5000 1/2/3
CNY17-2-000E 300 mil DIP6 60 63 125 10 5 0.3 10 2.5 5/5 70 1.7 60 5000 1/2/3
CNY17-3-000E 300 mil DIP6 60 100 200 10 5 0.3 10 2.5 5/5 70 1.7 60 5000 1/2/3
CNY17-4-000E 300 mil DIP6 60 160 320 10 5 0.3 10 2.5 5/5 70 1.7 60 5000 1/2/3
Dual Channel-8 pin ACPL-227-500E(Half pitch)
SO8 50 50 600 5 5 0.4 8 2.4 2/3 80 1.3 20 3000 1
ACPL-827-000E @ 300 mil DIP8 50 50 600 5 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3
Quad Channel-16 pin ACPL-247-000E(Half pitch)
SO16 50 50 600 5 5 0.4 8 2.4 2/3 80 1.3 20 3000 1
ACPL-847-000E 300 milDIP16
50 50 600 5 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3
Anode
Cathode
4
3
1
2
Collector
Emitter
Base
Collector
Emitter
Anode
Cathode
6
5
4
1
2
3
1 2 3 4
8 7 6 5
1 2 3 4
8 7 6 5
ll
1 2 3 4
16 15 14 13
5 6 7 8
12 11 10 9
1 2 3 4
16 15 14 13
5 6 7 8
12 11 10 9
ll
NEW
NEW
NEW
NEW
NEW
General Purpose Phototransistor Optocoupler AC Input
Device Part No. Package Absolute
Max. IFmA
CTR VCE(sat) tr/tfs
typ
BVCEOV
Min.
VF VISOVRMSMin.
Note
%Min. %Max. IF
mA VCE
V VMax. IF
mA IC
mA VMax. IF
mA
Single Channel-4 pin ACPL-214-500E
(Half pitch)SO4
+/-5020 400 5 5 0.4 8 2.4 2/3 80 1.4 20 3000 1
HCPL-354-000E SO4 +/-50 20 400 1 5 0.2 20 1 4/3 35 1.4 20 3750 1
HCPL-354-00AE SO4 +/-50 50 150 1 5 0.2 20 1 4/3 35 1.4 20 3750 1
HCPL-814-000E 300 mil DIP4 +/-50 20 300 1 5 0.2 20 1 4/3 35 1.4 20 5000 1/2/3
HCPL-814-00AE 300 mil DIP4 +/-50 50 150 1 5 0.2 20 1 4/3 35 1.4 20 5000 1/2/3
Dual Channel-8 pin ACPL-224-500E(Half pitch)
SO8 +/-50 20 400 1 5 0.4 8 2.4 2/3 80 1.4 20 3000 1
ACPL-824-000E 300 mil DIP8 +/-50 20 300 1 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3
Quad Channel-16 pin ACPL-244-500E(Half pitch)
SO16 +/-50 20 400 1 5 0.4 8 2.4 2/3 80 1.4 20 3000 1
ACPL-844-000E 300 milDIP16
+/-50 20 300 1 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3
Notes:
1 - IEC/EN/DIN EN 60747-5-2/5 Option 060 available, 2 - 0.4 Lead Spacing Option W00 available, 3 - Gull Wing SMD option available
* CTR rank with Option 000E, 00AE, 00BE, 00CE, 00DE and 00LE available, # - CTR rank with option 000E, 00AE, 00BE, 00CE and 00DE available
@ CTR rank with Option 000E, 00BE and 00CE available
CTR rank with option 500E, 50AE, 50BE, 50CE and 50DE available,
CTR rank with option 500E, 50BE, 50CE
- CTR rank with option 500E and 50AE available.
Collector
Emitter
nodeCathode
nodeCathode
4
3
1
1 2 3 4
8 7 6 5
1 2 3 4
1 6 1 5 1 4 1 3
5 6 7 8
1 2 1 1 1 0 9
NEW
NEW
NEW
NEW
NEW
8/13/2019 Optical Sensor Product Guide-Lr
40/60
40
Optoisolation and Optical Sensor Products
Solid State Relay (Photo MOSFET)
DescriptionAvago Technologies new ASSR Series arehigh-speed optically isolated MOSFET-output solid-state relays that featureperformance that has been qualified overa wide industrial temperature range of-40C to +85C. They are Form A (normallyopen) single-pole single-throw relays inindustry-standard 6-pin and 8-pin dual-in-line (DIP) packages, and 4-pin small outline(SO) packages. Their output ratings rangefrom 60V to 600V maximum load voltageand from 40mA to 2.5A continuous output
current. Their transient immunity of morethan 1kV/s and excellent noise rejectionbetween input-output as well as betweenopen terminals on the output will eliminateundesirable transient effects. Reinforcedinsulation of 3.75kV with fast switchingspeed makes them suitable for a wide rangeof industrial, consumer and automotiveapplications.
Compared to electromechanical relays,the ASSR Series offer distinct advantages,including the elimination of contact bounce,and problems due to shock, vibration, or
mounting position. They have no wearout mechanism limiting the number ofoperations, and require no minimumcontact wetting current. They are alsofree from magnetic fields, do not generateelectrical noise, and are not sensitive toelectromagnetic interference.
Benefits Superior to traditional electromechanical
relays (EMR)
Lower power consumption
Faster switching speed with hightransient immunity
Smaller size
Much better reliability
High reinforced insulation in miniatureSO-4 package
Qualied performance over- 40Cto +85C
Expanding portfolio to address diversiedmarket
Low R(ON )for less insertion loss
Low COFF)for better isolationperformance
High current capability with low R(ON)
General Purpose
The ASSR-14xx, ASSR-32xx and ASSR-41xxare designed for a wide variety of indus-trial and consumer electronics applica-
tions which includes telecommunicationsswitching, data communications, automaticmetering, medical system, security system,battery monitor, digital home appliances,set top boxes, etc.
Security Equipment Application Diagram
Applications
Telecommunicationsswitching
Data communications
Industrial control
Medical system
Security system
Automatic test equipment
Data acquisition system
Measuring instruments
EMR/reed relayreplacement
ASSR-xx20
Receiver / Alarm
Sensor / Detector Interface
ASSR-1218
Controller/Processor
Drive
Circuit
Sensor/Detector
(Motion,Sm
oke,
Light,etc.)
Sensor/Detector
(Motion,
Smoke,
Light,etc.)
8/13/2019 Optical Sensor Product Guide-Lr
41/60
41
Optoisolation and Optical Sensor Products
Low C(OFF)R(ON)
The ASSR-xxxC and ASSR-xxxR Series arespecifically designed for fast switchingapplications, commonly found in test and
measurement applications such as pinelectronics, data acquisition, multiplexers
and matrix cards, and switching in theanalog circuits of parametric measurement
unit (PMUs). The low output capacitance,
low on-resistance, and low output off-stateleakage current of the ASSR Series provide
higher system throughput and reduce
system errors. In addition to their fastswitching speeds, the ASSR Series providereinforced insulation of 3.75kV, which is
often required in industrial environments.
High Current
The ASSR-15x0, ASSR-1611 and ASSR-5211
are specifically designed for high currentapplications, commonly found in the
industrial applications. In programmablecontrollers, input and output modules
allow microprocessors to sense and controlvarious loads. An AC output module allows
logic-level voltages to control a switch thatturns AC loads on and off. For example,
the output module of a process controllermight be used to cont
Top Related