【Material】- For Mommy Pearl white/button/4-5mm ( item no. 4799101 ) 145 pcs
Wooden beads ( item no. 4717101 ) 36 pcs
Coral red/chips ( item no. 10414-LE-718 ) 42 pcs
Shell blue/round ( item no. 10653-LE-183 ) 19 pcs
Toggle clasp set 2 pcs
Jump ring 4mm 2 pcs
Finding w/3 loops ( item no. 25788-93 ) 2 pcs
Stringing wire 0.38mm ( item no. JW14T-0 ) 80cm 1 pcs
Stringing wire 0.38mm ( item no. JW14T-0 ) 30cm 3 pcs
Crimp 8 pcs
Wooden beads ( item no. 4717101 ) 60 pcs
Coral red/chips ( item no. 10414-LE-718 ) 6 pcs
Coral white/chips ( item no. 11068-LE-005 ) 34 pcs
Shell blue (wooden)/round ( item no. 10653-LE-183 ) 2 pcs
Shell blue/round ( item no. 10653-LE-183 ) 2 pcs
Cat-eye white/round ( item no. 1825310 ) 29 pcs
Jump ring 4mm 2 pcs
Crimp 2 pcs
Stringing wire 0.38mm ( item no. JW14T-0 ) 50cm 1 pcs
Clasp spring ring silver set 1 pcs
Double cup connector ( item no. 1921-42 )-bead tip 2 pcs
Supplemax clear cord 0.3mm 30cm 2 pcs
【Tools】 Cutter Pliers, Long and Round Nose Pliers
【Material】- For Me (Necklace + Ring)
Free DIY LessonE a s y T o M a k e & P r o u d T o W e a r
Me & Mommy Necklaces, Bracelet, Ring
【Instruction】Mommy--Necklace / Bracelet
Pearl
Wo
oden beads 36pcs
Shell Blue/round 19pcs
Coral Red 42pcs
Jump ring Finding w/3 loops
Toggle Clasp Step Take one end of stringing wire (80cm) and thread through crimp, then through the toggle clasp and back through the crimp (leave about 1.5~2cm). Then use long nose pliers to close the crimp (make sure it’s tight).
Step Thread the 145pcs pearls onto the stringing wire. finish by threading a crimp and the other half of the clasp just like you did in step 1.
Step Similar to steps 1 and 2, thread the 3 strands of beads as shown. then combine the findings with jump rings at both ends.
Stringing wire
Crimp
Mommy -- Necklace / BraceletApproximate Crafting Time: 1 hourMe -- Necklace + RingApproximate Crafting Time: 1 hour
Designed by Jennifer Howe, www.ecstaticjewelry.com
Skill
Level 1
【Instruction】Me--Necklace + Ring
Cat-eye white/4mm
Tip--How to make the knot and hide it
-Start
-end with knots
Make two knots nice and tight atthe same place.
Thread one end back to the
bead then pull until the knot is inside of the bead.
Shell blue (wooden)
Wooden
bead
s 30
pcs
Shell Blue
Coral White x 17pcs
From Step 1
Coral Red x 3pcs
Cat-eye white
Step - Necklace
Thread the beads as shown, and at the end thread double cup connector (bead tip). Squeeze the long nose pliers firmly to flatten the crimp bead. then hide it in the double cup connector (bead tip) and close the bead tip with long nose pliers. Finish by addingthe clasp set with jump rings.
Step - Necklace Squeeze the long nose pliers firmly to flatten the crimp bead. then hide it in the double cup connector (bead tip)and close the bead tip with long nose pliers.
Step - Necklace Take one 30cm supplemax clear cord and start at , follow the graphic as shown. Make the knot at and hide it in the closest bead.
Step - Ring Take one 30cm supplemax clear cord and start at , follow the graphic as shown. Make the knot at and hide it in the closest bead.
v
v
v
v
(Note: the graphic shows the single thread with two colors, this is just to illustrate which portion goes through which bead.)
double cup connector (bead tip)
Crimp
Stringing wire
v
v
Shell blue (wooden) Cat-eye white/4mm
1
2
3
9
10
(Note: The ring size depends on your finger size, add more beads to make it bigger)
** I would like to thank Beverly's for the sample beads. Since 1968, Beverly's has continued to be an indus-try leader in Crafts, Fabrics, home decor and much more. For further information please visit www.beverlys.com.
Top Related