8/12/2019 Making a Touch Sensor
1/11
Making a Touch Sensitive On/Off Circuit with Bare Paint and a 555 Timer
In this tutorial we are going to make a simple touch sensitive circuit using some Bare Paint, a 555 timer circuit, a couple of resistors, a LED
and a capacitor. The 555 timer is a fun and versatile integrated circuit (IC) that can be used in several distinct ways. There are loads of
interactive circuits that can be made with this chip, we'll be adding tutorials illustrating more of these projects in the future. Today we are
using the 555 with its internal flip-flop to sense the change in voltage at two inputs in the circuit. Luckly you don't need to know whats
happening inside the chip to enjoy the interactions that it affords!
When you touch the Bare Paint on either side of the gap you connect the circuit through your skindon't worry, the current is so low you will
not be able notice it. The 555 timer senses voltage change at pin 6 and pin 2, depending on which button you press, and flips the output
state at pin 3 - turning the LED ON or OFF. By the end of this tutorial you will have painted two touch buttons, with Bare Paint or a Bare Pen,
that connect to a touch sensitive ON/OFF 555 timer circuit. Once you have got this simple circuit going you are free to get even more
creative in using the paint to make different graphical touch buttons. Please send your electro-art works to us to put up on the community
site!
Components
Bare Paint
Paintbrush
PaperLM555 Integrated Circuit
Resistors
Bread Board
Jumper Wires
Capacitor
LED
Paper Clip Wires
9V Battery
http://vsagar.com/2011/12/16/how-ic-555-works-fundamentals-of-ic-555-its-basic-applications/http://www.bareconductive.com/store/products/bare-painthttp://www.bareconductive.com/store/products/bare-painthttp://www.bareconductive.com/store/products/bare-painthttp://www.bareconductive.com/store/products/bare-painthttp://vsagar.com/2011/12/16/how-ic-555-works-fundamentals-of-ic-555-its-basic-applications/8/12/2019 Making a Touch Sensor
2/11
8/12/2019 Making a Touch Sensor
3/11
Painting the On/Off Touch Buttons
Before you start to paint your buttons onto a non-conductive surface, such as paper, think about what form you would like the graphic to take.
You can think of the 'button' as a line of paint with a gap and at that gap you connect the circuit with your finger, thumb or other body part. So
make sure it is narrow enough for this. A very small current, imperceptible to a human, flows through the paint and across your skin when
you bridge the circuit over the paint-gap.
Second, paint your decided button graphic onto your surface with Bare Paint and a paintbrush. I have done this on paper and used a thin
piece of masking tape to ensure a clean thin break at my touch points. Below is my finished pair of touch buttons after being left to dry for
several minutes. I have made sure that the starts of my lines come close to the edge of the paper so that they can be reached by a paperclip.
8/12/2019 Making a Touch Sensor
4/11
Placing the Components and Connecting the Circuit
The next step is to assemble the simple circuit (pictured in the image below). Take a good look at the breadboard schematic and make sure
you have connected the circuit up correctly. You can download a copy of the breadboard schematichere.
http://www.bareconductive.com/file/555-touch-schematic-24-sept-pdfhttp://www.bareconductive.com/file/555-touch-schematic-24-sept-pdf8/12/2019 Making a Touch Sensor
5/11
Adding the Paperclip Wires
Once you have your circuit setup on your breadboard you can place your paperclip wires in the tracks indicated in your schematic and in the
images below. Take a look at our connecting tutorial which shows you how to make these cool prototyping wire - and other interesting ways
to connect to Bare Paint.
http://www.bareconductive.com/connectinghttp://www.bareconductive.com/connecting8/12/2019 Making a Touch Sensor
6/11
8/12/2019 Making a Touch Sensor
7/11
Testing
You can test it by first touching the blue paperclips together to turn the LED ON and then touching the yellow pair together to turn it OFF.
8/12/2019 Making a Touch Sensor
8/11
Connecting to Bare Paint
Now you can connect them to your touch buttons using the paperclip ends of the wires. Connect the blue wires to your ON touch button and
your yellow wires to your OFF touch button. You can simply place your finger, thumb or other body part at the gap to control you LED! It's
that simple and ultimately very satisfying!
8/12/2019 Making a Touch Sensor
9/11
Completed Circuit!
8/12/2019 Making a Touch Sensor
10/11
If this is working for you, you can now start experimenting with creating more interesting painted buttons with your paint - they don't even
need to look like buttons. Try using vinyl cutouts as stencils or even try screen printing if you have access to the equipment. Check out these
cool painted button below! Make sure to send in your crazy work so we can post it on our community wall - email us at
8/12/2019 Making a Touch Sensor
11/11
Top Related