FTI-CDK2 Type 1A - Vehicle Coverage & Preparation Notes
Make Model Year Install I/O ChangesCAN Lights RAP Trunk
Park / Auto
Hey! Read this stuff before you start the installation...
Firmware:Covered vehicles require BLADE-AL(DL)-CH4 firmware, flash module and update the controller firmware before installing.
CAN:In the event that troubleshooting is necessary, CAN connections are in the connector at the WIN (Wireless Ignition Node)
Lights:Type A MUX type parking lights are populated in the supplied 6-pin headlight switch connectoron the harness assembly, properly secure the unused 10-pin connector for safety
RAP:Type F - RAP shutdown handling for all other covered vehicles is at the driver door pin wire, purple wire located in the driver kick panel harness, circuit tests ( - ) negative with door open
Okay, now get to work...
WINWIN
WINWINWINWINWIN
WIN
WINWINWINWINWINWIN
WIN
AA
AAAAA
A
AAAAAA
A
FF
FFFFF
F
FFFFFF
F
CM
-900
CM-900S/900AS
CM7X00
CM7000/7200
CM900AS/900S Jumper
SUPPORT - 1(888) 820-3690, EXT. 203
DL-CH4
ChryslerChrysler
DodgeDodgeDodgeDodgeDodge
Jeep
RAMRAMRAMRAMRAMRAM
VW
300Town & Country
ChallengerChargerGrand CaravanMagnumRAM
Grand Cherokee
C/V15002500350045005500
Routan
2008-102008-10
2008-142008-102008-102008-09
2009
2011-13
20102010-122010-122010-122010-122010-12
2009-10
Type 1Type 1
Type 1Type 1Type 1Type 1Type 1
Type 1
Type 1Type 1Type 1Type 1Type 1Type 1
Type 1
DEREK ZOOLANDER
Est.
2001
CENTER KIDS
WHO CAN’T READ GOOD
AND WHO WANNA LEARN TO DO OTH
ER
ST
UF
F G
OO
D T
OO
IIIIIIIII
III
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIIIII
IIIIIII
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII
for
Cut loop for A/T
Green White/Blue
A B C D E
LED Programming Error CodesModule LED flashing RED during programming
1x - CAN issue2x - Immobilizer (confirm vehicle equipped, press button if not)3x - Immobilizer (confirm vehicle starts by key)4x - No VIN info5x - VIN mismatch (contact support)
12
SUPPORT - 1(888) 820-3690, EXT. 203
FTI-CDK2 Type 1A
Module Programming Procedure
1
2
PWRBLADE
Type AHeadlight Switch
Wireless Ignition Node
6
6
Type F ( - )
Driver kick panel harness
Purple ( - )E
W
AUTO
RE
AR
MW
A
D
E
Type B Parking light connections not required for this installation type. Please ensure that theunused connector is secured for safety
To provide control over vehicle Retained Accessory Power, configure controller POC forsetting #31 (RAP), see note for additional considerations.
Type F RAP control requires a connection to the purple wire originating at the driver doorpin, access is located in the driver kick panel harness
WTS (Wait to start) output from BLADE connector, connect to controller input for proper delayfor diesel vehicles. Properly insulate and secure if not used
E
FTI-CDK2 Type 1A - Installation Notes & Wiring Diagram
Step 1 - Wake BCM by closing then opening driver’s doorStep 2 - Activate IGN, module LED should turn redStep 3 - Wait for LED to begin rapidly flashing blueStep 4 - Remove key and press unlock on OEM key fob, if fob is unavailable/defective, press module button** IF BUTTON PRESS IS REQUIRED, KEYLESS CONTROL MAY REQUIRE ADDITIONAL PARTS OR WIRINGStep 5 - Programming complete when LED turns solid blue
A
D
*Not required
BLADE
CH4
WTS (+)
PRK MUX
Top Related