8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
1/20
EK6Earthing switch
Instruction manual
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
2/20
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
3/20EK6 |Contents 3
Thats why our instruct ion manual begins wi th these recom-
mendations:
Only install switchgear and/or switchboards in enclosed
rooms suitable for electrical equipment.
Ensure that installation, operation and maintenance are
carried out by specialist electricians only.
Comply in full with the legally recognized standards (IEC),
the connection conditions of the local electrical utility and the
applicable safety at work regulations.
Observe the relevant information in the instruction manual
for all actions involving switchgear and switchboards.
Danger!
Pay special attention to the hazard notes in the instruction
manual marked with this warning symbol.
Make sure that under operation condition of the switch-
gear or switchboard
the specified data are not exceeded.
Keep the instruction manual accessible to all persons con-
cerned with installation, operation and maintenance.
The users personnel are to act responsibly in all mat-
ters affecting safety at work and the correct handling of theswitchgear.
Your safety first always!
Contents
Page
1 Summary 4
2 Technical Data 4
3 Structure and Funktion 6
4 Installation 8
5 Maintenance 9
6 Dimensional drawings 10
If you have any further questions on this instruction manual,
the members of our field organization will be pleased to pro-
vide the required information.
WARNING
Always follow the instruction manual and
respect the rules
of good engineering practice !
Hazardous voltage
can cause electrical shocks and burns.
Disconnect power, then earth and short-circuit
before proceeding
with any work on this equipment.
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
4/204 Summary| EK6
1 SummaryEarthing switches of series EK6 are determined for indoor in-
stallation and conform to the requirements of IEC 62271-102.
They are f itted with snap-act ion operating mechanisms for
positive high-speed closing and sufficiently dimensioned to
conduct the rated short-circuit making current when closed
under load. The speed of the snap-action closing operation is
independent controls.
The earthing switches are supplied as kits wi th a pre-assem-bled active part and corresponding earthing contacts supplied
loose. Correct installation of these parts in a switchgear panel
results in a functioning earthing switch.
Routine tests to IEC 62271-102 arc to be carried out at site
accordingly.
2 Technical dataEarthing switch Pole
cen-
tres
Part number
Weight
Dimensional
drawing
RatedVoltage
Ratedimpulse
testvoltage
Ratedshort-time
current
Ratedshort-
circuitduration
Rated short circuit
making current(For various feed
directions)
Typ p
mm kg
Number Sheet U
kV
UI
kV
Ith
kA
tth
s
Ima
kA
Ima
kA
EK6-R-1208 -Z- 150 150 GCE 716 93 12 R11 01 111) GCEM360524 1 12 75 31.5 3 65 80
EK6-R-1208 -P- 150 150 GCE 716 93 12 R21 01 111) GCEM360524 1
EK6 1208 210 210 GCE 716 93 12 R01 02 121) GCEM360524 1
EK6 1208 275 275 GCE 716 93 12 R11 03 131) GCEM360524 2
EK6 1208 150 150 GCE 716 93 12 R01 14 13 GCEM700092 1
EK6 1208 210 210 GCE 716 93 12 R01 15 14 GCEM700092 1
EK6 1208 275 275 GCE 716 93 12 R01 16 16 GCEM700092 2
EK6 - 1212 - 210 210 GCE 700 17 32 R01 01 31 GCEM700059 1 40 3 120
EK6 - 1212 - 275 275 GCE 700 17 32 R01 02 31 GCEM700059 1 50 1 120
EK6 1706 150 150 GCE 716 93 12 R01 44 13 2) 17.5 95 31.5 3 80
EK6 1706 210 210 GCE 716 93 12 R01 42 14 2)
EK6 1706 210 210 GCE 716 93 12 R01 45 14 2)
EK6 1706 275 275 GCE 716 93 12 R01 46 16 2)
EK6-1710210 210 GCE 700 17 32 R01 06 31 2) 40 3 100
EK6-1710275 275 GCE 700 17 32 R01 05 31 2)
EK6-1710275 275 GCE 700 17 32 R01 04 312)
EK6 2406 210 210 GCE 716 93 12 R01 05 12 GCEM700092 5 24 125 25 3 50 63
EK6-R-2406-Z-210 210 GCE 716 93 12 R11 04 12 GCEM700092 5
EK6-R-2406-P-210 210 GCE 716 93 12 R21 04 12 GCEM700092 5
EK6 2406 275 275 GCE 716 93 12 M01 06 14 GCEM700092 6
EK6 2406 210 210 GCE 716 93 12 R01 17 14 GCEM700092 5
EK6 2406 275 275 GCE 716 93 12 R01 18 16 GCEM700092 6
EK6 2406 210 210 GCE 716 93 12 R01 19 14 GCEM700092 8 25 3 63
EK6 2406 275 275 GCE 716 93 12 R01 21 16 GCEM700092 9
1) without earthing contact
2) Dimensional drawings on request.
The earthing swi tches are su itable for the no rmal operati ng conditions of the
minus 5 indoor class.
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
5/20EK6 |Key to order code 5
Key to order code:
Earthing switch version Type designation
Earthing switch E
With snap action mechanism K
Design code 6
Mechanism on right R
Rated voltage 12 kV 12
Rated short circuit making current 80 kA 08
Predominantly for panel type ZK8 Z (P types predominantly for panel type ZP)
Pole centres 150 mm 150
Complete type designation E K 6 R 12 08 Z 150
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
6/206 Structure and Function| EK6
3 Structure and functionEarthing switches of series EK6 have three pairs of earthing
blades which are located on the operating shaft and are freely
movable. The pairs of earthing blades are electrically con-
nected to each other by a short-circuiting bridge and to earth
potential at the bearing brackets by two stranded copper
conductors. Driver levers and toggle springs located between
the bearing brackets are used to transmit the force during
the switching process. Fixing the active part on a torsionallyrigid switchgear panel wall or crossbeam provides it with the
necessary stability.
The earthing contacts designed to suit the relevant switch
type are to be bolted to the conductor bars supported on
suitable insulating parts, e.g. pintype insulators or current
transformers, on the opposite side and parallel to each other,
and the position adjusted until it conforms to that show in the
dimensional drawings.
Figure 1: Example of the active part
of an earthing switchmounted on a
switchgear panel partition, shown in
the open position.
1 Bearing bracket
2 Toggle spring
3 Short-circuiting bridge
4 Pair of earthing blades
5 Eathing conductor
6 Bevel gear mechanism
(not belonging to the
earthing switch)
7 Actuating shaft
8 Driver lever
6 7 8
321 4 5
The earthing switch has a snap action clos ing mechanism
which functions independently of the rotation of the drive
shaft. The switching speed and torque achieved in this proc-
ess are independent of the actions of the operating mecha-
nism.
In the opening process, in contrast, the toggle springs have
no effect on the speed of contact separation.
A r ing lever or su itable manual or motor ized operating mecha-nism with the necessary torque for the type of switch and an
operating angle 90 can be fitted for operation of the switch.
Note:
Always open earthing switches by turning until
the stop is reached.
The earthing switches can also be fitted with an auxil iary
switch for annunciation purposes.
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
7/20EK6 |Structure and Function 7
11 9 2 78
10 10.1
Figure 2: Example of an earthing
switch mounted in a switchgear
panel, shown in the closed position.
2 Toggle spring
7 Actuating shaft
8 Driver lever
9 Setting ring
10 Earthing contact10.1 Earthing tongue
11 Current transformer
Figure 3: Live parts of an earthing
switch with a rated short-circuit
making current of 120 kA, mounted
on a sheet steel partition.
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
8/208 Instalation| EK6
4 InstalationWhen installing earthing switches in switchgear panels, the
following details must be taken into account if perfect switch-
ing functions etc. are to be achieved:
The active part of the earthing switch is supplied in the
open position and with pretensioned toggle springs.
The earthing switch can be installed in any position.
Do not operate the switch without earthing contacts!
Install the active part and earthing contacts without stressor distortion and parallel to each other on a torsionally
rigid and flat panel wall/crossbeam and conductor bar
respectively.
Precisely maintain the spatial/dimensional position of the
earthing contacts relative to the active part as shown in
the dimensional drawing for the relevant switch type.
Only use insulated mountings with a cantilever strength
equivalent to a cast resin pin type insulator to DIN 48136:
For switches to dimensional diagram GCEM 360524,
sheets 1 and 2 and GCEM 700092, sheets 1, 2, 5, 6, 8
and 9: Form B, 12 kV or 24 kV, 7.5 kN
For switches to dimensional diagram GCEM 700059,sheet 1: Form C, 12 kV, 16 kN
Fit the operating mechanism.
The operating shaft can be moved after the two setting
rings have been released. Observe the tightening torque of
4 Nm for the M6 threaded pins.
Adjust the motion sequence of the earthing blades in rela-
tion to the earthing contacts as follows:
1. Grease the contact areas.
2. Close the switch with the fixing bolts in the earthing
contacts loosely tightened.
3. Check that the blade pairs are properly located on the
contact tongues of the earthing contacts and adjust ifnecessary.
4. Tighten the fixing bolts and carry out a test switching
operation.
5. Maximum permissible deviation between the central
position of the earthing blades and the contact tongues
of the earthing contacts:
1 mm for switches to dimensional diagram GCEM
360524, sheets 1 and 2, and GCEM 700092, sheets
1, 2, 5, 6, 8 and 9
0.6 mm for switches to dimensional diagram GCEM
700059, sheet 1.
Measuring Point: Clearance between the earthingblades and the contact tongues during opening.
Take care when handling the switch!
6. Irrespective of the routine testing of the relevant switch-
gear panels/switchboard to IEC 62271-200, the earthing
switch is to be subjected to routine testing in accordance
with IEC 62271-102, on completion of installation.
Check for unimpeded function of the high-speed
switching system when the switch has been installed
without stress or distortion.
Check the tightening torque for the M 12 hexagon nuton the short-circuiting bridge, possibly removing a pair
of earthing blades to provide access. This torque is
important for correct function!
Rated tightening torque:
without lubricant: 86 Nm
with oil or grease lubricated: 40 Nm.
Bolt the copper earthing conductors to the bearing
brackets and connect the other ends to the switch-
board earthing bar.
Perform at least 20 mechanical opening and closing
operations on the earthing switch after completion of
installation. Auxiliary switches:
Auxiliary switches on the side wall of the switchgear
panel:
2 x 5 pole auxiliary switches:
GCE 8282292R0101
(contact arrangement as per order)
Signalling of open and closed positions
Operation by rod mechanism (engages with M 12
threaded bar)
Auxiliary switches on the rear wall of the switchgear
panel:
S1 + S2 (2 NCC + 2 NOC = 2 change-over): GCE7169 272 R0108
S1 + S2 + S3 (3 NCC + 3 NOC = 3 change-over):
GCE 7169 272 R0107
Signalling of the closed position only.
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
9/20
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
10/20
Partnumber
Type
p
a
c
g
f
Md
Md
Weight
OFF
ON
kg
GCE7169312R0
102
EK6-1208-210
210544
4202
470-2
58
210Nm
110Nm
12
GCE7169312R2
101
EK6-R-1208-P-150
150424
3001
950-2
100
210Nm
110Nm
11
GCE7169312R1
101
EK6-R-1208-Z-150
150424
3002
470-2
48
210Nm
110Nm
11
EarthingswitchEK6
Dim
ensionaldrawing
12kV-Types
GCEM360524,Sheet1
+)maximumprojectionofcontact
blades:5mm
(rateddimensions:3mm)
E=Earthingco
ntact,H=Auxiliaryswitch,L=Ratingplate
,
S=Operating/Switchingangle,W=
Shaftsection,C=ON
,O=OFF,
Contactbladedistance:
8
0,3
mm
Contactthickness:
10
mm
Contactforce:
734
N
Contactspringforce(cupsprings):
313
N
Operatingangle:
90O
Switchingangle:
90O
Seesection4fortheauxiliaryswitchesfitted
Caution!
Observethenotesoninstallationinsection4.
19,7
90
30-0,10
A-A
W
f
p
25
p
g
B
96
3
c
A A
a
36
225
50
(195)
16035
22
48
96
25 5
L9x19
5
H
L
25
B
R174
35
,5
502
510
1176
25
25723
8
7
40
20
29
40
153
8
65
5890
265
0
S
13
10
-
255+1,5
13
GCE8684219P0101
E:
15
*)*
)
E:GCE838
4542P0180
B-B
30 6
0
R174 2
50
+30
75
1726
26
275
10
17
12
90
87
35
,5
58
S C
0 29
40
6
15
80
40
11
13
E:GCE6186188P0101
10 Dimensionals drawing| EK6
6 Dimensionals drawing
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
11/20EK6 |Dimensionals drawing 11
Partnumber
Type
p
a
c
g
f
Md
Md
Weight
OFF
ON
kg
GCE7169312R0
103
EK6-1208-275
275674
5501
950-2
100
210Nm
110Nm
13
EarthingswitchEK6
Dim
ensionaldrawing
12kV-Types
GCEM360524,Sheet2
E=Earthingco
ntact,H=Auxiliaryswitch,L=Ratingplate
,
S=Operating/Switchingangle,C=ON,O=OFF,
Contactbladedistance:
8+
0,3
mm
Contactthickness:
10
mm
Contactforce:
734
N
Contactspringforce(cupsprings):
313
N
Operatingangle:
90O
Switchingangle:
90O
Seedimensiona
ldrawingGCEM360524,
sheet1,forsha
ftprofile
Seesection4forauxiliaryswitchesfitted
Caution!
Observethenotesoninstallationinsection4.
f
p
2
5
p
g
1726
26
275
10
30
40
1
1
13
60
R174
250+30
75
17
12
87
29
40
589
0
S
35
,5
S C
0
6
15
80
E:GCE6186188P0101
B-B
115
c
96
p
a
36
225
50
(195)
16035
22
48
96
25 5
3
L9x19
5
H
L
25
B B
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
12/2012 Dimensionals drawing| EK6
32 20
9
170
32
13/13,5
68
E:GCE7003225P0101
40
R174
262-+
1,5
262-+
1,5
45
2+
35
,5
87
29
40
589
0
0 S
- 95+4
20
15
73-+4
C
S
B-B
k
96
3c
a
36
225
50
(195)
16035
22
48
96
25 5
L9x19
5
H
L
25
B B
f
p
p
g
Y
EarthingswitchEK6
Dim
ensionaldrawing
12kV-Types
GCEM700092,Sheet1
E=Earthingswitch,H=Auxiliaryswitch,L=Ratingplate,
Y=Viewdirectio
nforswitchposition
S=Operating/S
witchingangle,C=ON,O=OFF,
Seesection4fo
rtheauxiliaryswitchesfitted
SeedimensionaldrawingGCEM360524,sheet1,
forshaftprofile
Caution!
Observethenotes
oninstallationinsection4.
Partnumber
Type
p
a
c
g
f
k
Md
Md
Weig
ht1)
OFF
ON
kg
GCE7169312R0
114
EK6-1208-150
150424
3001
60
75
75
220Nm
120Nm
13
GCE7169312R0
115
EK6-1208-210
210544
4201
75
50
100
220Nm
120Nm
13
1)includingearthingcontact(Weight3Pieces:1,8kg)
Contactbladedistance:
8
0,3
mm
Contactthickness:
9
mm
Contactforce:
739
N
Contactspringforce(cupsprings):
720
N
Operatingangle:
90O
Switchingangle:
90O
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
13/20EK6 |Dimensionals drawing 13
f
p
p
g
Y
20
940
170
3232
13/13,5
68
GCE7003225P0101
E:
C
262-+
1,5
262-+1
,5
45
2+
35
,5
87
R17429
40
589
0
0 S
- 95+4
20
15
73-+4
S
B
-B
96
115
100
c
p
a
36
225
50
(195)
16035
22
48
96
25 5
3
L9x19
5
H
L
25
B B
Partnumber
Type
p
a
c
g
f
Md
Md
Weight1)
OFF
ON
kg
GCE7169312R0
116
EK6-1208-275
275674
5502
10
50
220Nm
120Nm
16
1)includingearthingcontact(Weight3Pieces:1,8kg)
EarthingswitchEK6
Dim
ensionaldrawing
12kV-Types
GCEM700092,Sheet2
E=Earthingco
ntact,H=Auxiliaryswitch,L=Ratingplate
,
Y=Viewdirectionforswitchpositionindicator
S=Operating/Switchingangle,C=ON,O=OFF,
Seesection4fortheauxiliaryswitchesfitted
Seedimensiona
ldrawingGCEM360524,sheet1,
fortheshaftpro
file
Caution!
Observethenotesoninstallationinsection4.
Contactbladedistance:
8
0,3
mm
Contactthickness:
9
mm
Contactforce:
739
N
Contactspringforce(cupsprings):
720
N
Operatingangle:
90O
Switchingangle:
90O
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
14/20
f
262-1,5 +
Y
p
p
g
15
40
0-0,2
225
96
48
k
c
p
a
36
(195)
16035
96
L9x19
L
25
96
22
B B
50
94
36
38
15
R2
0
92
1708020
262-
1,5
+R
210
50
35
,5
589
0
210
13
GCE7001716
P0101
E:
0
C
S
90
20
13
B-B
I
EarthingswitchEK6
Dim
ensionaldrawing
12kV-TypesforZS-Feeder
GCEM700059,Sheet1
E=Earthingco
ntact,I=Isolator,L=Ratingplate,
Y=Viewdirectionforswitchpositionindicator(ZS1-Type),
S=Operating/Switchingangle,C=ON,O=OFF,
SeedimensionaldrawingGCEM360524,sheet1,
forshaftprofile
Caution!
Observethenotesoninstallationinsector4.
Contactbladedistance:
38,5
mm
Contactthickness:
40
mm
Contactforce:
500
N
Operatingangle:
90O
Switchingangle:
90O
0-0,60
-0,2
14 Dimensionals drawing| EK6
Partnumber
Type
p
a
c
g
f
k
Md
Md
Weight1)
OFF
ON
kg
GCE7001732R0
102
EK6-1212-275
275674
5502
10
50
100
300Nm
190Nm
31
GCE7001732R0
101
EK6-1212-210
210544
4201
75
60
100
300Nm
190Nm
31
1)includingearthingcontact
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
15/20
f
p
p
g
X Y
32
321-
1,5
+
73-+4
321-
1,5
+
5
- 95+4
R233
20
15
45
2+
35
,5
87
29
40
5890
S
SE
SE
0
C
S
B-B
40
GCE7003225P0101
20
9
170
3232
13/13,5
68
E:
96
100
3
c
a
36
225
50
(195)
16035
22
48
96
25 5
L9x19
5
H
L
25
B B
EarthingswitchEK6
Dim
ensionaldrawing
24kV-Types
GCEM700092,Sheet5
SeedimensionaldrawingGCEM360524,
sheet1,forshaftprofile
Seesection4forauxiliaryswitches
fitted.
C
aution!
O
bservethenotesoninstallation
in
section4.
Partnumber
Type
p
a
c
g
f
Md
Md
Weight1)
OFF
ON
kg
GCE7169312R0
117
EK6-2406-210
210544
4201
75
50
220Nm
120Nm
14
GCE7169312R0
105
EK6-2406-210
210544
4204
7
258
220Nm
120Nm
12
GCE7169312R1
104
EK6-R-2406-Z-210
210544
4202
58
47
220Nm
120Nm
12
GCE7169312R2
104
EK6-R-2406-P-210
210544
4201
90
115
220Nm
120Nm
12
1)includingearthingcontact(Weight3Pieces:1,8kg)
0-2
E=Earthingco
ntact,H=Auxiliaryswithch,L=Ratingplate,S=Operating/Switchingangle,
SE=Controlelectrodevarieswithpaneldesign;X=Viewdirection
forswitchpositionindicator,Y=viewdirectionforswitchp
ositionindicator,
C=ON,O=OFF,
Contactbladedistance:
8
0,3
mm
Contactthickness:
9
mm
Contactforce:
353
N
Contactspringforce(cupsprings):
376
N
Operatingangle:
90O
Switchingangle:
90O
EK6 |Dimensionals drawing 15
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
16/2016 Dimensionals drawing| EK6
Partnumber
Type
p
a
c
g
f
Md
Md
Weight1)
OFF
ON
kg
GCE7169312R0
118
EK6-2406-275
275674
5502
10
50
220Nm
120Nm
16
GCE7169312M0106
EK6-2406-275
275674
5501
20
55
220Nm
120Nm
14
1)includingearthingcontact(Weight3Pieces:1,8kg)
EarthingswitchEK6
Dimensionaldrawing
24kV-Types
GCE
M700092,Sheet6
E=Earthingswitch,H=Auxiliaryswitch,L=Ratingplate,S
=Operating/Switchingangle
SE=Controlele
ctrodevarieswithpaneldesign;X=Viewd
irectionforswitchpositionindicator,Y
=Viewdirection
forswitchpositionindicator,
C=ON,O=OF
F,
Contactbladedistance:
80,3
mm
Contactthickness:
9
mm
Contactforce:
35
3
N
Contactspringforce(cupsprings):
37
6
N
Operatingangle:
90
O
Switchingangle:
90
O
Seesection4forauxiliaryswitchesfitted.
SeedimensionaldrawingGCEM360524,
sheet1,fortheshaftprofile
Ca
ution!
Ob
servethenotesoninstallationinSection4.
0-2
f
p
p
g
X Y
20
940
170
323213/13,5
68
GCE7003225P0101
E:
R233
73-+4
321-
1,5
+
321-
1,5
+
32
5
- 95+4
20
15
45
2+
35
,5
87
29
40
589
0
S
SE
SE
0
C
S
B-B
115
225
100
c
96
p
a
36
50
(195)
16035
22
48
96
25 5
3
L9x19
5
H
L
25
B B
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
17/20EK6 |Dimensionals drawing 17
Partnumber
Type
p
a
c
g
f
Md
Md
Weight1)
OFF
ON
kg
GCE7169312R0
119
EK6-2406-210
210544
4201
75
50
220Nm
120Nm
14
1)includingearthingcontact
EarthingswitchEK6
Dim
ensionaldrawing
24kV-Types
GCE
M700092,Sheet8
Contactbladedistance:
80
,3
mm
Contactthickness:
9
mm
Contactforce:
353
N
Contactspringforce(cupsprings):376
N
Operatingangle:
90O
Switchingangle:
90O
E=Earthingcontact,H=Auxiliaryswitch,L=Ratingplate,S=Operating/Switching
angle,SE=Con
trolelectrodevarieswithpaneldesign;
Y=Viewdirectionforswitchpositionindicator,C=ON,O=OFF,
See
dimensionaldrawingGCEM360524,
sheet1,forshaftprofile
See
section4forauxiliaryswitchesfitted.
Cautio
n!
Observethenotesoninstallationinsection4.
f
p
p
g
Y
9
20
GCE7003225P0102
E
120
40
222
32 32
13/13
,5
c
96
100
3
a
36
225
50
(195)
16035
22
48
96
25 5
L9x
19
5
H
L
25
B B
R233
321
-1
,5
+
125-+4
32
15
45
2+
35
,5
87
29
40
589
0
S
SE
SE
0
C
S
5E
B
-B
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
18/2018 Dimensionals drawing| EK6
Partnumber
Type
p
a
c
g
f
Md
Md
Weight1)
OFF
ON
kg
GCE7169312R0
121
EK6-2406-275
275674
5502
10
50
220Nm
120Nm
16
1)includingearthingcontact
EarthingswitchEK6
Dimensionaldrawing
24kV-Types
GCE
M700092,Sheet9
Contactbladedistance:
80,3
mm
Contactthickness:
9
mm
Contactforce:
35
3
N
Contactspringforce(cupsprings):
37
6
N
Operatingangle:
90
O
Switchingangle:
90
O
E=Earthingcon
tact,H=Auxiliaryplate,L=Ratingplate,S
=Operating/Switching
angle,SE=Con
trolelectrodevarieswithpaneldesign;
Y=Viewdirectio
nforswitchpositionindicator,C=ON,O=
OFF
Seedim
ensionaldrawingGCEM360524,
sheet1,forshaftprofile
Seesec
tion4forauxiliaryswitchesfitted
Caution!
Observeth
enotesoninstallationinsection4.
f
p
p
g
Y
120
940
222
32 32
13
/13,5
20
GCE7003225P0102
E:
R233
321
-1,5
+
147-+4
125-+4
32
15
45
2+
35
,5
87
29
40
589
0
S
SE
SE
0
C
S
5E
B-
B
B
115
225
100
c
96
p
a
36
50
(195)
16035
22
48
96
25 5
3
L
9
x19
5
H
L
25
B
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
19/20EK6 |Dimensionals drawing 19
8/12/2019 MA_EK6 (EN) 12,24 kV 2009.04.06
20/20
1VLM000047Rev.-,en2009.04.06ABB s.r.o.
Videnska 117
619 00 Brno, Czech Republic
E-mail: [email protected]
Tel.: +420 547 152 413
Fax: +420 547 152 190
The data and ilustrat ions in this catalogue are not
binding. We reserve the right to make changes of the
content, in the course of technical development of the
product.
Top Related