Download - LH201_9900sb

Technical SpecificationSandvik LH201Sandvik LH201Sandvik LH201Sandvik LH2019-900 S-B

2007-06-01

2007 Sandvik Mining and Construction

APPLICATION

Sandvik LH201 is a true compact and flexible full Dieselloader for narrow vein mining.

The highest possible rate of productivity is ensured byfast and easy one pass loading.

Sandvik LH201 layout is designed for good visibility andbalance.This and the powerful four-wheel-drive articulatedchassis ensure fast and safe manoeuvering in tightspaces.

All the service points are well protected but easy toaccess.

CAPACITIES

Tramming capacity 1 000 kg (2 200 lb)Breakout force, lftt 10.7 kN - 1 094 kg (2 407 lb)Breakout force, tilt 36.9 kN - 3 766 kg (8 285 lb)Tipping load 2 941 kg (6 470 lb)Bucket std. 0.54 m (0.7 yd), 500 BNH lip

BUCKET MOTION TIMES

Raising time 2.6 sec.Lowering time 1.5 sec.Tipping time 4.1 sec.

WEIGHTS

Operating weight 3 650 kg (8 030 lb)Total loaded weight 4 650 kg (10 230 lb)Shipping weightAxle weights without loadFront axle 1 120 kg (2 460 lb)Rear axle 2 530 kg (5 570 lb)Axle weights with loadFront axle 2 630 kg (5 790 lb)Rear axle 2 020 kg (4 440 lb)Unit weight is dependent on the selected options.

DRIVING SPEEDS FORWARD AND REVERSE

Loaded, max 9 km/h (5.6 mph)

1215

1645 1525 1430

4600

1030

2045

1055

1050

1840

3190

1890

36

220

1/4


2007-06-01


SERVICE CAPACITIES

Fuel tank 40 liters (10.5 gal.)Hydraulic oil tank 62 liters (16.4 gal.)Hydrostatic transmission oil tank 31 liters (8.2 gal.)

FRAME

Rear and front frame Welded steel constructionMaterial E 36.3Central hinge Spherical bearings

(large angle)

ENGINE

Diesel engine Deutz F3L 912WOutput 33 kW (45 hp) / 2 500 rpmTorque 170 Nm / 1 500 rpmNumber of cylinder In line 3Displacement 2 827 cmCooling system Air cooledCombustion principle 4-stroke, 2-stage combustionElectric system 12 V starter and accessoriesAir filtering Oil bath air cleanerExhaust system Catalytic purifier

TRANSMISSION

Hydrostatic transmission Variable flowfully reversible

One pump Linde, variable displacement0 to 42 cm/rev

One motor Linde, fixed 35 cm/rev

TRANSFER CASE

Type GearLocation Rear axle

AXLES

Front and rear Tamrock, fixedNo-spin in front axle

Central hinge oscillation 10

WHEELS

Tires 8.25 x 15Air pressure, front and rear 3.5 bar (350 kPa)

BRAKES

Dynamic service brake through the hydrostatictransmission.The parking and emergency brake is spring applied,hydraulically released multidisc oil immersed brakesinclosed on the transfer case.

STEERING

Full hydraulic, centre-point articulation, power steeringwith two double acting cylinders. Steering controlled bystick, interlock protection.Turning angle 36Turning radius inner 1840 mm (72)

outer 3190 mm (125)Main components in steering system:

Main valve HPIControl valve DanfossSteering hydraulic cylinders 2 pcs, 60 mm (2.36),

TamrockPressure settings:

Main relief valve 14.0 Mpa (170 bar)Shock load valves 17.5 Mpa (175 bar))

BUCKET HYDRAULICS

Full hydraulic open center system with one gear pump.The oil flow from steering hydraulic pump is directed to bucket hydraulics when steering is not used.Equipped with mechanical dual control lever.Lift cylinder 1 pcs, 100 mm (3.9)Tilt cylinder 1 pcs, 120 mm (4.7)Pressure setting for:

Main relief valve 14.0 Mpa (140 bar)Bucket tilt 6.0 Mpa (60 bar)Bucket roll-back 18.0 Mpa (180 bar)Boom raise 18.0 Mpa (180 bar)Boom lower 6.0 Mpa (60 bar)

Main components:Bucket hydraulic cylinders TamrockControl valve Commercial hydraulicsFittings JIC

ELECTRICAL EQUIPMENT

Alternator 45 A, BoschBattery 1 x 12 V, 95 AhStarter 1.7 kW, 12 VDriving and working lights font, 2 pcs (H1 55 W)

rear, 2 pcs (H1 55 W)

OPTIONAL EQUIPMENT

*) Bucket size 0.5 m (0.7 yd), width 950 mm (37).FOPS-ROPS safety canopy.Reverse alarm.Emergency steering system.Complete spare wheel.*) EU, UL, CSA, AUS norms package.

*) replaces standard component

2/4


2007-06-01


GRADEABILITY & SPEED

PRODUCTIVITY CURVE

0

10

20

30

40

50

60

0 1 2 3 4 5 6 7 8 9

GRADE (%)

SPEED (kph)

TONNESPER HOUR

0

10

20

30

40

50

60

0 50 100 150 200 250 300 350 400 450

ONE WAY DISTANCE IN METRES

0 % 20 %

Basic data for calculations :

Payload 1 000 kgOverall speed limit 8.5 km/hFixed cycle time 0.5 min.Rolling resistance 3 %

Fixed cycle time includes the time for filling, dumping, turning and accelerating

Slope / Grade Hor./0 1:5/20Loaded speed (kph) 8.5 7.1Empty speed (kph) 8.5 8.5

3/4


2007-06-01

Sandvik Mining and Construction reserves the right to change this specification without further notice.

Sandvik Mining and Construction Lyon S.A.S. B.P.46 - FR-69881 Meyzieu Cedex, FranceTel. +33 4 7245 2200, Telefax +33 4 7831 7980www.sandvik.com

DUMP DATA

CAGING DIMENSIONS

1500

2320

1745

1290

600

835

42

4/4

3698

3463

3453

1215

1215

991

1055

1055

1055

Bucket and canopy removed ...........................................3 287 kg

Bucket, canopy and lift arms removed ...........................3 107 kg

Bucket, canopy, lift arms, axles and tires removed.......2 372 kg