© 2020 Knoll Inc.
Knoll VA IDIQMTR PLAYBOOK
2© 2020 Knoll Inc. 2© 2020 Knoll Inc.
CasegoodsModular Desking
3© 2020 Knoll Inc.
4© 2020 Knoll Inc.
MD1 – Modular Desking System – High Pressure Laminate, Free Standing
› Meet ANSI/BIFMA supporting loads.› HPL tops and components of minimum 1” thick particleboard or MDF with moisture balancing
backing sheet, pre-drilled metal to metal connections, and minimum 3mm vinul T-mold orThermoform edge in colors to match a variety of HPL tops to include solid colors, woodgrain, andflecked finish.
› Upper Storage component construction to be nominal 5/8” thick particle board or MDF substratewith HPL covering, 1mm edge banding, metal to metal connections, full adjustable hinges, locksavailable,
› Pedestal and drawer construction to be 5/8” thick particle board or MDF substrate with HPLcovering, 1mm edge banding, metal to metal connections; integral file rails; locking; have noisedampening closures; and have 1” minimum adjustable floor glides with nylon foot. Staples are notacceptable.
› Full extension steel ball bearing suspension› Available in 2 depths to fit under 24” and 30”d tops› BBF, FF, lateral file, multi- file, and Mobile pedestal configurations› Drawer interiors to be clear finished MDF, wood, or laminate covered plywood with same material
drawer bottoms. Paperboard is not acceptable.› Lateral file drawer construction to be 5/8” thick particle board or MDF substrate with HPL covering,
1mm edge banding, metal to metal connections; integral file rails; locking; have noise dampeningclosures; and have 1” minimum adjustable floor glides with nylon foot. Staples are not acceptable.
› Lateral files must be available in widths from 30” – 42”› Full extension steel ball bearing suspension› Drawer interiors to be clear finished MDF, wood, or laminate covered plywood with same material
drawer bottoms. Paperboard is not acceptable.
5© 2020 Knoll Inc.
MD1 – Modular Desking System – High Pressure Laminate, Free Standing – Reff Profiles Vol.2
THIS TYPICAL INCLUDES:
(1) 48”W x 24”D WORKSURFACE(1) 72”W X 30”D WORKSURFACE(1) FLOORSTANDING BOX/BOX/FILE PEDESTAL(1) FLOORSTANDING FILE/FILE PEDESTAL(1) 72”W HUTCH WITH TACKBOARD(1) TASK CHAIR – REMIX, SEE TS1
6© 2020 Knoll Inc.
MD1 – Modular Desking System – High Pressure Laminate, Free Standing – Reff Profiles Vol.2
THIS TYPICAL INCLUDES:
(1) 54”W x 24”D WORKSURFACE(1) 66”W X 24”D WORKSURFACE(1) FLOORSTANDING BOX/BOX/FILE PEDESTAL(1) FLOORSTANDING LATERAL FILE(1) 66”W HUTCH WITH TACKBOARD(1) 72”H BOOKCASE WITH FILE DRAWERS(1) TASK CHAIR – LIFE, SEE TS1
7© 2020 Knoll Inc.
MD1 – Modular Desking System – High Pressure Laminate, Free Standing – Reff Profiles Vol.2
THIS TYPICAL INCLUDES:
(1) 48”W x 24”D WORKSURFACE(1) 72”W X 24”D WORKSURFACE(1) 72”W X 30”D WORKSURFACE(1) FLOORSTANDING BOX/BOX/FILE PEDESTAL(1) FLOORSTANDING FILE/FILE PEDESTAL(1) BULKHEAD FULSE PEDESTAL(1) MODESTY PANEL(1) 72”W HUTCH WITH TACKBOARD(1) TASK CHAIR – REGENERATION, SEE TS1(1) DUAL MONITOR ARM – SAPPER, SEE CS2
8© 2020 Knoll Inc.
MD1 – Modular Desking System – High Pressure Laminate, Free Standing – Reff Profiles Vol.2
THIS TYPICAL INCLUDES:
(1) 48”W x 24”D WORKSURFACE(1) 72”W X 24”D WORKSURFACE(1) 72”W X 24”D WORKSURFACE(1) FLOORSTANDING BOX/BOX/FILE PEDESTAL(1) FLOORSTANDING LATERAL FILE(1) 72”W HUTCH WITH TACKBOARD(1) 72”H FLOORSTANDING BOOKCASE
9© 2020 Knoll Inc.
MD2 – Modular Desking System – High Pressure Laminate Tops with Metal Components, Free Standing
› Meet ANSI/BIFMA supporting loads. › HPL tops and components of minimum 1” thick particleboard or MDF with moisture balancing
backing sheet, pre-drilled metal to metal connections, and minimum 3mm vinul T-mold or Thermoform edge in colors to match a variety of HPL tops to include solid colors, woodgrain, and flecked finish.
› Upper Storage component construction to be nominal 5/8” thick particle board or MDF substrate with HPL covering, 1mm edge banding, metal to metal connections, full adjustable hinges, locks available,
› Pedestal and drawer construction to be 5/8” thick particle board or MDF substrate with HPL covering, 1mm edge banding, metal to metal connections; integral file rails; locking; have noise dampening closures; and have 1” minimum adjustable floor glides with nylon foot. Staples are not acceptable.
› Full extension steel ball bearing suspension› Available in 2 depths to fit under 24” and 30”d tops› BBF, FF, lateral file, multi- file, and Mobile pedestal configurations› Drawer interiors to be clear finished MDF, wood, or laminate covered plywood with same material
drawer bottoms. Paperboard is not acceptable.› Lateral file drawer construction to be 5/8” thick particle board or MDF substrate with HPL covering,
1mm edge banding, metal to metal connections; integral file rails; locking; have noise dampening closures; and have 1” minimum adjustable floor glides with nylon foot. Staples are not acceptable.
› Lateral files must be available in widths from 30” – 42”› Full extension steel ball bearing suspension› Drawer interiors to be clear finished MDF, wood, or laminate covered plywood with same material
drawer bottoms. Paperboard is not acceptable.
10© 2020 Knoll Inc.
MD2 – Modular Desking System – High Pressure Laminate, Free Standing – Dividends Horizon (Modeled after JSN E0057-ALT)
THIS TYPICAL INCLUDES:
(2) LOCKABLE FLIPPER UNITS(1) TASKLIGHT(1) TACKBOARD(1) TOOLRAIL(2) PAPER TRAYS(1) DIAGONAL TRAY(2) FREESTANDING WORK SURFACE(1) ADJUSTABLE KEYBOARD TRAY(1) MOBILE PEDESTAL BOX/FILE
11© 2020 Knoll Inc.
MD2 – Modular Desking System – High Pressure Laminate, Free Standing – Dividends Horizon (JSN E0078-ALT)
THIS TYPICAL INCLUDES:
(1) FREESTANDING WORK SURFACE(1) FREESTANDING PENINSULA WORK SURFACE(2) LOCKABLE FLIPPER UNITS(2) SHELVES, STORAGE/DISPLAY(2) LIGHTS(1) TOOLRAIL(1) PAPER TRAY(1) DIAGONAL TRAY(1) ADJUSTABLE KEYBOARD TRAY(1) MOBILE PEDESTAL, BOX/FILE
12© 2020 Knoll Inc.
MD2 – Modular Desking System – High Pressure Laminate, Free Standing: Knoll Dividends Horizon
THIS TYPICAL INCLUDES:
(1) 72”W X 30”D WORKSURFACE(1) 48”W X 30”D WORKSURFACE(1) 72” STEEL OVERDESK CABINET WITH TACKBOARD(1) FLOORSTANDING BOX/BOX/FILE PEDESTAL(1) FLOORSTANDING FILE/FILE PEDESTAL(1) TOOLRAIL/LOAD BAR, SEE DA1(1) SLANTED PAPER SORTER– ORCHESTRA SYSTEM ACCESSORIES, SEE DA1(1) MONITOR ARM – SAPPER, SEE CS2(1) TASK CHAIR – REGENERATION, SEE TS1
13© 2020 Knoll Inc.
MD2 – Modular Desking System – High Pressure Laminate, Free Standing: Knoll Antenna Workspaces
THIS TYPICAL INCLUDES:
(1) 78”x30” ANTENNA DESK TOP(1) 42”x 30” ANTENNA DESK TOP(1) FLOORSTANDING METAL PEDESTAL
–BOX/BOX/FILE(1) 72” ANTENNA FENCE(1) METAL CABINET WITH SLIDING
DOOR (1) 42” DESK SCREEN(1) TASK CHAIR – LIFE, SEE TS1(1) MONITOR ARM – SAPPER, SEE CS2
14© 2020 Knoll Inc.
MD2 – Modular Desking System – High Pressure Laminate, Free Standing: Knoll Antenna Workspaces
THIS TYPICAL INCLUDES:
(1) 72”x30” ANTENNA BIG DESK(1) 72” L SHARED METAL CABINET(2) 60”x24” ANTENNA DESK TOP(2) FLOORSTANDING METAL BOX/BOX/FILE PEDESTALS(2) MODESTY DESK SCREENS(2) TASK CHAIR – REMIX, SEE TS1
15© 2020 Knoll Inc.
MD3 – Modular Desking System – Wood Veneer, Freestanding
› Traditional, transitional, and contemporary image options available.› Veneer surfaces shall be 1-3/16 to 1-9/16” slipmatched or bookmatched cherry, walnut or maple
veneers over minimum 1” thick substrate with solid wood and 3mm PVC edge band options. Also available with a HPL Top.
› Chassis construction shall be of 1-1/8” thick or better substrate with wood veneer as described above; fully finished back panels; ¾” thick back panels; and secured with non-visible screws, dowels, wood joints, and other brackets to ensure maximum strength. Staples are not acceptable.
› Pedestal and drawer construction to be 5/8” thick particle board or MDF substrate with wood veneer covering, solid wood edge banding; full extension telescoping steel ball bearing suspension; integral file rails; locking; available in 2 depths to fit under 24” and 30”d tops; BBF, FF, lateral file, multi-file
› Mobile pedestal configurations and full height lateral files of varying drawer heights shall have noise dampening closures; and have 1.5” minimum adjustable floor glides with nylon foot for stationary files. Drawer fronts and pulls to be field replaceable. Staples are not acceptable. Drawer interiors to be clear finished MDF, wood, or laminate covered plywood with same material drawer bottoms. Paperboard is not acceptable.
› Lateral file drawer construction to be 5/8” thick particle board or MDF substrate with wood veneer covering, solid wood edge banding; full extension telescoping steel ball bearing suspension; integral file rails; locking; have noise dampening closures; and have 1” minimum adjustable floor glides with nylon foot. Drawer fronts and pulls to be field replaceable. Staples are not acceptable. Drawer interiors to be clear finished MDF, wood, or laminate covered plywood with same material drawer bottoms.Paperboard is not acceptable.
› FSI Certified Wood Sources
16© 2020 Knoll Inc.
MD3 – Modular Desking System – Wood Veneer, Freestanding : Knoll Reff Vol. 2
THIS TYPICAL INCLUDES:
(1) 54”W x24”D VENEER WORKSURFACE(1) 66”W X 24”D VENEER WORKSURFACE(2) FLOORSTANDING VENEER BOX/BOX FILE PEDESTALS66” VENEER HUTCH WITH TACKBOARD72”H BOOKCASE WITH FILE DRAWERS
17© 2020 Knoll Inc.
MD3 – Modular Desking System – Wood Veneer, Freestanding : Knoll Reff Vol. 2
THIS TYPICAL INCLUDES:
(1) 48”W x24”D VENEER WORKSURFACE(1) 72”W X 24”D VENEER WORKSURFACE(1) 72”W X 30”D VENEER WORKSURFACE(1) FLOORSTANDING VENEER BOX/BOX FILE PEDESTALS(1) FLOORSTANDING VENEER LATERAL FILE72” HUTCH – BACKPAINTED GLASS FRONT WITH TACKBOARD36”W X 72”H VENEER FLOORSTANDING BOOKCASE(1) TASK CHAIR – LIFE, SEE TS1(1) MONITOR ARM – SAPPER, SEE CS2
18© 2020 Knoll Inc.
MD3 – Modular Desking System – Wood Veneer, Freestanding : Knoll Reff Vol. 2
THIS TYPICAL INCLUDES:
(1) 66”W x24”D VENEER WORKSURFACE(1) 72”W X 24”D VENEER WORKSURFACE(2) FLOORSTANDING VENEER BOX/BOX FILE PEDESTALS(1) FLOORSTANDING VENEER 72”H CABINET
WITH COAT ROD66” VENEER HUTCH WITH TACKBOARD(1) TOOLRAIL/LOAD BAR, SEE DA1(1) SLANTED PAPER SORTER– ORCHESTRA SYSTEM ACCESSORIES, SEE DA1(1) TASK CHAIR – REGENERATION, SEE TS1
19© 2020 Knoll Inc.
MD3 – Modular Desking System – Wood Veneer, Freestanding : Knoll Reff Vol. 2
THIS TYPICAL INCLUDES:
(1) 72”W x30”D VENEER WORKSURFACE(1) 42”W X 24”D VENEER WORKSURFACE(1) 72”W X 30”D VENEER WORKSURFACE(1) PARTIAL MODESTY PANEL(1) 16”W BOX/BOX/FILE PEDESTAL (1) 16”W FILE/FILE PEDESTAL(1) 36”W FILE/FILE PEDESTAL(1) MONITOR ARM – SAPPER, SEE CS2(1) TASK CHAIR – REGENERATION, SEE TS1
20© 2020 Knoll Inc.
MD3 – Modular Desking System – Wood Veneer, Freestanding : Knoll Reff Vol. 2 and k.stand
THIS TYPICAL INCLUDES:
(1) 96”W x24”D VENEER WORKSURFACE(1) 42”W X 24”D VENEER WORKSURFACE(1) 72”W X 30”D VENEER HEIGHT ADJUSTABLE
TABLE – k.stand(1) PARTIAL MODESTY PANEL(1) 16”W BOX/BOX/FILE PEDESTAL (1) 16”W FILE/FILE PEDESTAL(1) 36”W FILE/FILE PEDESTAL(1) MONITOR ARM – SAPPER, SEE CS2(1) TASK CHAIR – LIFE, SEE TS1(2) GUEST CHAIRS – MUUTO FIBER, SEE GC1
PENDINGAPPROVAL
21© 2020 Knoll Inc. 21© 2020 Knoll Inc.
Filing and Storage
22© 2020 Knoll Inc.
23© 2020 Knoll Inc.
LF1 – File, Lateral, Metal
› 5H units may be comprised of a flip top retractable drawer face on the top module.› A variety of widths 30”, 36” and 42” wide and 18” or 20” depths (+/- ¼”)› Counterweight option must be able to be added in the field› Ability to add on modules in the field› Multiple base heights› Positive interlock safety function allowing only one drawer to open at a time› Drawers shall operate with full extension, telescoping, steel ball-bearing slides for full access to all
drawer contents and smooth operation› Leveling Glides that provide 1" adjustment range› Optional posting shelf› Optional label holders› Common top options to span over multiple units in either HPL or wood› Additional modules for combination storage such as sliding door, double swing door or open
shelving (bookcase
24© 2020 Knoll Inc.
LF1 – File, Lateral, Metal – JSN F0110
THIS STANDARD INCLUDES:
BOOKCASE, 58”H x 36”W x 15”D3 ADJUSTABLE SHELVES
25© 2020 Knoll Inc.
LF1 – File, Lateral, Metal – JSN F0115
THIS STANDARD INCLUDES:
BOOKCASE, 85”H x 36”W x 15”D5 ADJUSTABLE SHELVES
26© 2020 Knoll Inc.
LF1 – File, Lateral, Metal – JSN F0415
THIS STANDARD INCLUDES:
5 DRAWER LATERAL FILING CABINET 64.4”H x 42’W x 18”DLOCKING, WITH LABEL HOLDERS.4-12” DRAWERS WITH HANGING RAILS1-13.5” RECEDING DOOR WITH FIXED SHELF
27© 2020 Knoll Inc.
LF1 – File, Lateral, Metal – JSN F0420
THIS STANDARD INCLUDES:
2 OR 3 DRAWER LATERAL FILING CABINET 24”W x 18”D LOCKING, WITH LABEL HOLDERS, 2 OR 3 – 12” DRAWERS WITH HANGING RAILS
28© 2020 Knoll Inc.
LF2 – File, Lateral, HPL
› Availabe 36” wide and 20” deep (+/-2”)› Counterweight required › Positive interlock safety function allowing only one drawer to open at a time› Drawers shall operate with full extension, telescoping, steel ball-bearing slides for full access to all
drawer contents and smooth› Leveling Glides that provide 1" adjustment range› Common top options to span over multiple units in either HPL or wood› Additional widths and depths available
29© 2020 Knoll Inc.
LF2 – File, Lateral, HPL: Reff Profiles
THIS STANDARD INCLUDES:
2 DRAWER LATERAL FILING CABINET 36”W x 20”DHIGH PRESSURE LAMINATE CASE AND WORKSURFACE TOP METAL INTERIORMETAL PULLLOCKED DRAWERS
30© 2020 Knoll Inc.
LF2 – File, Lateral, HPL: Reff Profiles
THIS STANDARD INCLUDES:
(1) BOX-BOX-FILE CABINET 36”W x 20”D(1) OPEN BOOKCASE CABINET 36” X 20”D 72”W X 20”D HIGH PRESSURE LAMINATE WORKSURFACE TOP METAL INTERIORMETAL PULLLOCKED DRAWERS
31© 2020 Knoll Inc.
LK1 – Lockers, Metal
› Variety of openings ranging from box to full height lockers (1 Tier, 2 Tier, 3 Tier, 4 Tier, 5 Tier and box openings)
› Available in 12 – 18” depth and 12” wide› Hooks to be zinc plated forged steel, ball ends.› Ventilated doors› Multiple lock options including personal padlock hasps, integrated key or integrated combination
lock› Individual locker identification (numbers, letters, or combination)› 16 gauge steel minimum construction› Leveling Glides that provide 1" adjustment range› Interior shelf option for full height opening› Variety of powder coated finish colors› Factory assembled option› ADA Compliant lockers (recessed handles with multi- point latch) option› Additional accessories such as base enclosures, sloped top› Filer panel offered as needed
32© 2020 Knoll Inc.
LK1 – Lockers, Metal: Knoll Quoin
THIS STANDARD INCLUDES:
50”H X15”WX X 24”D FULL DOOR STEEL LOCKER WITH TOP –LEFT HAND (DIGITAL KEYPAD LOCK)
PENDINGAPPROVAL
33© 2020 Knoll Inc.
LK1 – Lockers, Metal: Knoll Quoin
THIS STANDARD INCLUDES:
(2) 50”H X12”WX X 15”D FULL DOOR STEEL LOCKER WITH TOP –LEFT HAND (BARREL LOCK)
(2) 50”H X12”WX X 15”D FULL DOOR STEEL LOCKER WITH TOP –RIGHT HAND (BARREL LOCK)
(1) 50”H X12”WX X 15”D OPEN LOCKER WITH SHELVES AND TOP
PENDINGAPPROVAL
34© 2020 Knoll Inc.
LK2 – Lockers, HPL
› Variety of openings ranging from box to full height lockers (1 Tier, 2 Tier, 3 Tier, 4 Tier, 5 Tier, 2 door “Z” and box openings)
› Available in 12 – 18” depth and 12” wide› Hooks to be zinc plated forged steel, ball ends.› Leveling Glides that provide 1" adjustment range› Multiple lock options including personal padlock hasps, integrated key or integrated combination
lock› Individual locker identification (numbers, letters, or combination)› ¾” 45 lb. density particle board with HPL› Interior shelf option for full height opening› Variety of laminate finish colors
35© 2020 Knoll Inc.
LK2 – Lockers, HPL: Knoll Anchor
THIS STANDARD INCLUDES:
(1) 64”H X12”WX X 24”D DOUBLE-DOOR LEFT-HAND (DIGITAL KEYPAD LOCK)(1) 12”W X 23.5”D LOCKER TOP
PENDINGAPPROVAL
36© 2020 Knoll Inc.
LK2 – Lockers, HPL: Knoll Anchor
THIS STANDARD INCLUDES:
(2) 42”H X12”WX X 20”D FULL DOOR LOCKERLEFT HAND (STANDARD LOCK) WITH COAT HOOK
(1) 42”H X12”WX X 20”D OPEN LOCKER WITH SHELVES(1) 36”W X 19”D LAMINATE LOCKER TOP
PENDINGAPPROVAL
37© 2020 Knoll Inc. 37© 2020 Knoll Inc.
Modular Systems Furniture
38© 2020 Knoll Inc.
39© 2020 Knoll Inc.
MSP1 – Panels, Monolitic
› Panel assemblies shall have corrugated honeycomb paperboard FR rated core or other alternate assembly to provide internal stability to the panel insert and covering that prevents cracking, bending, and gouging of the insert. The 60” wide panel shall have a center stile .
› Panel surface may be of powder coated sheet metal or high pressure laminate over hardboard “sandwich type” with top and bottom rail assembly OR Insert in frame assembly.
› Minimum thickness of panel covering shall be 1/8”.› Structural panel system of 2” min. thickness +/- 1/4" to support worksurfaces; adjustable on 1”
increments› Assemblies with empty cavities that do not support the fabric inserts will not be acceptable.› A fire retardant layer laid over the hardboard or metal shall be of layered fiberglass and reflective
foil.› Fabric will be stretched over the scrim and stapled to the frame around the perimeter of the core or
alternately receive an fabric covered insert over hardboard or rated structural foam.Options: › Optional Acoustic panel to have a Noise Reduction Coefficient of .65 higher or a Sound
Transmission Class of 18 or higher depending upon the level of sound performance required.Glazed Panels: › The glazing is to be ¼” thick, smoked or clear acrylic sheet edged with a rigid PVC extrusion color
matched to the frame.› A glazing retainer to secure the glazing in the frame shall be made of rigid PVC.Options: › Partial height glazing with other sections of fabric, metal, or laminate.› Frosted or patterned glazing.› Add on upper glazing panels are allowed.Open Frame Panels: › Panel frame structure without internal components to be completely finished and smooth.› Panel shall retain hanger frames for mounting of components.
40© 2020 Knoll Inc.
MSP2 – Panels, Frame and Tile:
› To meet the characteristics of the above panels with the added feature of allowing individual tiles to comprise the panel covering.
› The tiles shall be standard in 12”,24”, 36”, and 48” heights (+/- 3") as well as full panel height.› Coverings shall be available in fabrics, vinyl, wood, laminate, acrylic (both patterned and frosted),
and metals.› Tiles shall have a substrate of fiberboard, metal, or other suitable surface that prevents
deformation and cracking of the tile. Unsupported tiles with foam structure only are not acceptable› Attaching fasteners shall require a device that prevents accidental dislodging and prevent users
from removing the tiles.› Fully assembled frame and tile system of 2 1/2” min. thickness +/- 1/4" to support worksurfaces;
adjustable on 1” incrementsOptions: › Optional Acoustical ratings of the panel must feature a Noise Reduction Coefficient of .65-.75 and
a Sound Transmission Class of 18-24 depending upon the level of sound performance required.
MSW1 – Worksurfaces:
› Worksurfaces shall be 1-1/8” thick minimum particleboard or MDF with a high pressure laminate top face, underside, and rigid, extruded integral color vinyl side edges. Aformed metal understructure is also allowable with integral laminate rolled edge.
› Holes shall be pre-drilled in the underside of the work surface for the installation of drawers, mounting brackets, and suspended pedestals.
› The work surface shall have a gap at the rear to permit cord passage or alternately include a grommet of at least 2.5” diameter.
› Worksurfaces supports shall be powered coated painted minimum 18 gauge or better high strength sheet steel with integral attachment hooks.
› Components shall include a means to be leveled.› Worksurfaces should hold 200 lbs of concentrated weight without failing or deforming.› Work Surface Shapes- a variety of sizes in rectangular, peninsula, jetty, corner, and other shaped
tops.
41© 2020 Knoll Inc.
MSS1 – Storage, Overhead:
› Overhead storage units must be available in widths 24”, 30", 36", 42", 48” and 60", adjustable in 1” increments. Storage unit shall be secured to prevent accidental dislodging.
› Shelf and storage case to be constructed of 18” gauge steel or better. Doors to be constructed of 14 gauge steel or better.
› Overhead bin doors may be of several styles and coverings but shall include a powder coated paint option and a lift-assist mechanism option.
› Standard lift mechanism shall include a ball bearing suspension with noise dampening closure.› Shelf shall include an integral backstop and rail underneath to hold a task light.Options: › Partial and full height open shelf units; frosted acrylic, sliding overlap doors, and HPL or fabric
doors
MSS2 – Storage, Underdesk – Pedestals and Files:
› To be constructed of 22 gauge or better cold rolled steel, painted metal frame with a formed 22 gauge or better sheet steel drawer case with powder coated paint finish.
› Drawer fronts shall be of either ¾” minimum HPL over particleboard or painted metal with replaceable fronts.
› File drawers shall have full extension telescoping, steel ball bearing suspension rated to hold 90 pounds minimum and Integral filing rails.
› Leveling glides shall be standard with nylon foot pad adjustable up to 1”.› All drawers shall be full box construction type.› Laminate storage case construction is not allowed as part of the modular systems furniture
category. Refer to Modular Casegoods to find requirements for laminate case storage.
42© 2020 Knoll Inc.
MSP1, MSW1, MSS1, MSS2 – Modular Systems Furniture: Panels, Monolitic: Knoll Dividends Horizon 8’x8’
THIS TYPICAL INCLUDES:
(1) 36”W x 36”H MONOLITHIC PANEL WITH 14”H FRAMELESS GLASS TOPPER
(2) 48”W X 36”H MONOLITHIC PANELS WITH 14”H FRAMELESS GLASS TOPPER
(2) 48”W X 64”H MONOLITHIC PANELS WITH WORKSTATION HEIGHT ELECTRICAL
(1) 30”W X 64”H MONOLITHIC PANEL(1) 96”W X 30”D LAMINATE WORKSURFACE(1) 66”W X 24”D LAMINATE WORKSURFACE(1) FLOORSTANDING 30”W FLOORSTANDING
STEEL LATERAL FILE (1) STEEL FILE/FILE PEDESTAL (2) 48”W PANEL MOUNTED OVERHEAD(1) 30” DIA. X-BASE TABLE(1) TASK CHAIR – LIFE, SEE TS1(2) GUEST CHAIRS – OLLO, SEE GC1
43© 2020 Knoll Inc.
MSP1, MSW1, MSS1, MSS2 – Modular Systems Furniture: Panels, Monolitic: Knoll Dividends Horizon 6’x8’
THIS TYPICAL INCLUDES:
(2) 36”W x 50”H MONOLITHIC PANELS(2) 48”W X 64”H MONOLITHIC PANEL(1) 72”W X 30”D LAMINATE WORKSURFACE(1) 66”W X 24”D LAMINATE WORKSURFACE(1) FLOORSTANDING 30”W FLOORSTANDING
STEEL LATERAL FILE (2) STEEL MOBILE BOX/FILE PEDESTAL (2) 48”W X 14”H PANEL MOUNTED SLIDING DOOR OVERHEAD
(1) TASK CHAIR – REGENERATION, SEE TS1(1) DUAL MONITOR ARM – SAPPER, SEE CS2
44© 2020 Knoll Inc.
MSP1, MSW1, MSS1, MSS2 – Modular Systems Furniture: Panels, Monolitic: Knoll Dividends Horizon 6’ x 7’-6”
THIS TYPICAL INCLUDES:
(2) 36”W x 50”H MONOLITHIC PANELS(1) 24”W X 50”H MONOLITHIC PANEL(1) 60”W X 50”H MONOLITIHIC PANEL(1) 30”W X 50”H LAMINATE GALLERY PANEL(1) 70”W X 23”D K.STAND HEIGHT
ADJUSTABLE TABLE, SEE HAW3(1) 50”H X 15”W X 24”D ANCHOR SLIDE OUT
TOWER, SEE LK2(1) 48”W X 20”D ANCHOR CREDENZA
(1) TASK CHAIR – REGENERATION, SEE TS1(1) DUAL MONITOR ARM – SAPPER, SEE CS2
PENDINGAPPROVAL
45© 2020 Knoll Inc.
MSP2, MSW1, MSS1, MSS2 – Modular Systems Furniture: Panels, Tiled: Knoll Dividends Horizon 6’x6’
THIS TYPICAL INCLUDES:
(4) 36”W x 42”H TILED PANELS WITH 14”H STACKING FROSTED GLASS SCREEN.
(1) 72”W X 24”D LAMINATE WORKSURFACE(1) FLOORSTANDING 15”W FLOORSTANDING
STEEL PEDESTAL(1) 46”W X 29”D K.STAND HEIGHT
ADJUSTABLE TABLE, SEE HAW3(1) TASK CHAIR – REMIX, SEE TS1
PENDINGAPPROVAL
46© 2020 Knoll Inc.
MSP2, MSW1, MSS1, MSS2 – Modular Systems Furniture: Panels, Tiled: Knoll Dividends Horizon 6’x6’
THIS TYPICAL INCLUDES:
(2) 36”W x 50”H TILED PANELS(2) 36”W X 64”H TILED PANELS(1) 24”W X 64”H TILED PANEL(1) 24”W X 50”H TILED PANEL(2) 36”W X 24”D LAMINATE WORKSURFACES(1) 24”W X 24”D CURVILINEAR CORNER
LAMINATE WORKSURFACE(1) FLOORSTANDING 15”W FLOORSTANDING
STEEL PEDESTAL(1) STEEL MOBILE BOX/FILE PEDESTAL WITH
WITH CUSHION TOP(2) 36”W PANEL MOUNTED OVERHEAD
(1) TASK CHAIR – REMIX, SEE TS1(1) HANGING PENCIL CUP, HANGING UTILITY TRAY – ORCHESTRA SYSTEM ACCESSORIES, SEE DA1
47© 2020 Knoll Inc.
MSP1, MSW1, MSS1, MSS2 – Modular Systems Furniture: Panels, Monolitic: Knoll Dividends Horizon 4’ x 6’
THIS TYPICAL INCLUDES:
(1) 36”W x 64”H MONOLITHIC PANELS(1) 36”W X 64”H TILED PANEL WITH SLATWALL(2) 24”W X 64”H MONOLITHIC PANELS(2) 48”W X 24”D LAMINATE WORKSURFACES(1) STEEL MOBILE BOX/FILE PEDESTAL (1) 36”W PANEL MOUNTED OVERHEAD(1) 36”W PANEL MOUNTED SHELF(1) 24”W PANEL MOUNTED OVERHEAD(1) SINGLE MONITOR ARM – SAPPER, SEE CS2(1) HANGING PENCIL CUP, HANGING UTILITY TRAY – ORCHESTRA SYSTEM ACCESSORIES, SEE DA1
48© 2020 Knoll Inc.
MRS1 – Modular Reception Stations:
› Ability to provide solutions to patient privacy and separation at check-in.› Ability to meet ADA wheelchair requirements at check- in counter on forward and/or side
approach.› HPL and Solid Surface top options.› Solid surface transaction top standard› Tiled, stacking panel system of 2 1/2" min. thickness +/- 1/4" to support worksurfaces and provide
patient privacy at Registration. Heights up to 84” with acoustical fabric, hard surface painted metal, hard surface vinyl, wood veneer, laminate, and glass or acrylic clear, frosted, or patterned tile options.
› Ability to contain and distribute power and data with UL listed products.› Refer to Panels: Frame and Tile section 2 above for additional product details.Options: › Base panel/kickplate, front of station applied decorative protection bands or tiles.› Solid surface tiles.
49© 2020 Knoll Inc.
MRS1 – Modular Reception Stations: Dividends Horizon 6’ x 6’
THIS TYPICAL INCLUDES:
(1) 24”W x 64”H MONOLITHIC PANEL(1) 48”W X 64”H MONOLITHIC PANEL(1) 48”W X 42”H MONOLITHIC PANEL(1) 24”W X 42”H MONOLITHIC PANEL(2) 24”W X 24”D LAMINATE WORKSURFACES(1) 48”W X 24”D RECTILINEAR CORNER
WORKSURFACE(1) 72”W X 15”D LAMINATE TRANSACTION
WORKSURFACE(1) STEEL MOBILE BOX/FILE PEDESTAL (1) 48”W PANEL MOUNTED OVERHEAD(1) 24”W PANEL MOUNTED OVERHEAD(1) TASK CHAIR – LIFE, SEE TS1(1) SINGLE MONITOR ARM – SAPPER, SEE CS2
50© 2020 Knoll Inc.
MRS1 – Modular Reception Stations: Dividends Horizon 8’ x 6’
THIS TYPICAL INCLUDES:
(2) 48”W X 64”H MONOLITHIC PANEL(1) 48”W X 42”H MONOLITHIC PANEL(1) 24”W X 42”H MONOLITHIC PANEL(1) 24”W X 24”D LAMINATE WORKSURFACE(1) 48”W X 24”D LAMINATE WORKSURFACE(1) 48”W X 24”D RECTILINEAR CORNER
WORKSURFACE(1) 72”W X 15”D LAMINATE TRANSACTION
WORKSURFACE(1) STEEL MOBILE BOX/FILE PEDESTAL (1) FLOORSTANDING STEEL FILE/FILE (2) 48”W PANEL MOUNTED OVERHEAD(1) TASK CHAIR – REGENERATION, SEE TS1(2) SLANTED PAPER SORTER– ORCHESTRA SYSTEM ACCESSORIES, SEE DA1(1) 48”W LOAD BAR/INFO RAIL, SEE DA1
51© 2020 Knoll Inc.
MRS1 – Modular Reception Stations: Dividends Horizon 8’ x 6’
THIS TYPICAL INCLUDES:
(2) 36”W X 64”H MONOLITHIC PANEL(1) 48”W X 64”H MONOLITHIC PANEL(1) 48”W X 42”H MONOLITHIC PANEL(1) 36”W X 42”H MONOLITHIC PANEL(2) 72”W X 24”D LAMINATE WORKSURFACE(1) 48”W X 24”D LAMINATE WORKSURFACE(1) 42”W X 15”D LAMINATE TRANSACTION
WORKSURFACE(1) 30”W X 15”D LAMINATE TRANSACTION
WORKSURFACE(1) 15”W X15”D CORNER COUNTER WORKSURFACE (1) STEEL MOBILE BOX/FILE PEDESTAL (2) 48”W PANEL MOUNTED OVERHEAD(1) TASK CHAIR – REGENERATION, SEE TS1(2) SLANTED PAPER SORTER– ORCHESTRA SYSTEM ACCESSORIES, SEE DA1(1) 48”W LOAD BAR/INFO RAIL, SEE DA1
52© 2020 Knoll Inc.
MRS1 – Modular Reception Stations: Dividends Horizon 7’ x 6’
THIS TYPICAL INCLUDES:
(2) 36”W X 64”H MONOLITHIC PANEL(1) 24”W X 64”H MONOLITHIC PANEL(1) 48”W X 42”H MONOLITHIC PANEL(2) 24”W X 42”H MONOLITHIC PANEL(1) 30”W X 42”H MONOLITHIC PANEL(2) 72”W X 24”D LAMINATE WORKSURFACE(1) 60”W X 24”D LAMINATE WORKSURFACE(1) 36”W X 24”D LAMINATE WORKSURFACE(1) 60”W X 15”D LAMINATE TRANSACTION
WORKSURFACE (1) STEEL FLOORSTANDING BOX/BOX/FILE
PEDESTAL (1) 36”W PANEL MOUNTED OVERHEAD(2) 36”W PANEL MOUNTED SHELVES(1) TASK CHAIR – REGENERATION, SEE TS1
53© 2020 Knoll Inc.
CGS1 – Caregiver Team Stations (also Nurse Stations):
› Coordinating Height adjustable work and team tables.› Coordinating Height adjustable de-centralized Nurse Work stations in rectangular, 120 degree,
and “cove” top designs.› Tiled, stacking panel system of 3” min. thickness to support worksurfaces and provide patient
privacy at Registration. Heights up to 84” with acoustical fabric, hard surface painted metal, perforated metal, hard surface vinyl, wood veneer, laminate, and glass or acrylic clear, frosted, or patterned tile options.
› Ability to contain and distribute power and data with UL listed products.› Refer to Panels: Frame and Tile section 2 above for additional product details.need to confirm
location of "Section 2“
54© 2020 Knoll Inc.
CGS1 – Caregiver Team Stations (also Nurse Stations): Dividends Horizon/k.stand
THIS TYPICAL INCLUDES:
(2) 48”W X 82”H TILED LAMINATE PANEL ONE SIDEMONOLITHIC FABRIC SIDE 2
(1) 30”W X 82”H TILED LAMINATE PANEL ONE SIDEMONOLITHIC FABRIC SIDE 2
(1) 72”W X 24”D LAMINATE WORKSURFACE(1) 42”W X 15”D LAMINATE TRANSACTION
WORKSURFACE (1) 72”W X 15”D LAMINATE TRANSACTION
WORKSURFACE (1) 15”W X 15”D CORNER LAMINATE TRANSACTION
WORKSURFACE (1) STEEL MOBILE BOX/FILE PEDESTAL (1) 48”W X 30”D HEIGHT ADJUSTABLE WORKSURFACE(1) TASK CHAIR – LIFE, SEE TS1
55© 2020 Knoll Inc.
CGS1 – Caregiver Team Stations (also Nurse Stations): Dividends Horizon/k.stand
THIS TYPICAL INCLUDES:
(2) 48”W X 82”H TILED LAMINATE PANEL ONE SIDEMONOLITHIC FABRIC SIDE 2
(1) 30”W X 82”H TILED LAMINATE PANEL ONE SIDEMONOLITHIC FABRIC SIDE 2
(1) 72”W X 24”D LAMINATE WORKSURFACE(1) 42”W X 15”D LAMINATE TRANSACTION
WORKSURFACE (1) 72”W X 15”D LAMINATE TRANSACTION
WORKSURFACE (1) 15”W X 15”D CORNER LAMINATE TRANSACTION
WORKSURFACE (1) STEEL MOBILE BOX/FILE PEDESTAL (1) 48”W X 30”D HEIGHT ADJUSTABLE WORKSURFACE(1) TASK CHAIR – LIFE, SEE TS1
56© 2020 Knoll Inc.
CGS1 – Caregiver Team Stations (also Nurse Stations): JSN E0403
THIS TYPICAL INCLUDES:
(2) PANEL FRAME, 42”H X 24”W (1) PANEL FRAME, 27”H X 48”W(2) 2-WAY 135 DEGREE CONNECTORS, 42”H(2) FINISHED END TRIM HARDWARE(1) CANT. LOW ACCESS WORK SURFACE 135
DEGREE(8) PANEL INSERTS, FABRIC(8) PANEL INSERTS, LAMINATE(1) PAPER MANAGEMENT RAILS 24W(2) COUNTER TOP W/LIGHT(3) PAPER TRAY
57© 2020 Knoll Inc. 57© 2020 Knoll Inc.
Tables and Carts
58© 2020 Knoll Inc.
59© 2020 Knoll Inc.
CT1 – Conference Table, HPL:
› A variety of top sizes to include 36” – 240” Long 30”- 60” Deep› A variety of shapes to include round, rectangle, boat, sight line,› A variety of HPL options including wood grain and non- wood grain with hard wood edging option.› A variety of edge details to include but not limited to, T-Mold/Edgeband, Square and Knife.› Power/USB/data/voice port options with the option of grommet hole(s) and cover, Power Island,
troughs or power cove(s).› Power options to be corded or hardwired.› Wire management underneath conference table.› A variety of bases to include metal, wood, powder coated, cylinder, Panel, four post, and
rectangle.› Leveling glides for carpet or hard floorsOptions: › Casters› Coordinating Storage Credenza and Tower options
60© 2020 Knoll Inc.
CT1 – Conference Table, HPL: Knoll Reff Conference Worksurface with Drum Base
AVAILABLE DIMENSIONS:
SQUARE: • 36” X 26-1/2”H• 42” X 26-1/2”H• 48” X 26-1/2”H• 60” X 26-1/2”H• 72” X 26-1/2”H
RECTANGULAR: • 72”W X 30/36”D X 26-1/2”H• 84”W X 30/36/42”D X 26-1/2”H• 96”W X 30/36/42”D X 26-1/2”H• 120”W X 30/36/42”D X 26-1/2”H• 144”W X 42/48””D X 26-1/2”H• 168”W X 42/48””D X 26-1/2”H• 196”W X 42/48””D X 26-1/2”H
EDGE OPTIONS:
RACETRACK: • 72”W X 30/36”D X 26-1/2”H• 84”W X 30/36/42”D X 26-1/2”H• 96”W X 30/36/42”D X 26-1/2”H• 120”W X 30/36/42”D X 26-1/2”H• 144”W X 42/48””D X 26-1/2”H• 168”W X 42/48””D X 26-1/2”H• 196”W X 42/48””D X 26-1/2”H
ROUND: • 36”DIA.X 26-1/2”H• 42”DIA.X 26-1/2”H• 48”DIA.X 26-1/2”H• 60”DIA.X 26-1/2”H• 72”DIA.X 26-1/2”H
61© 2020 Knoll Inc.
CT1 – Conference Table, HPL: Knoll Rockwell Unscripted –Library Tables
AVAILABLE DIMENSIONS:
• 144”W X 60”D X 28”H (0 OR 6 GROMMETS)• 192”W X 60”D X 28”H (0 OR 8 GROMMETS)• 240”W X 60”D X 28”H (0, 8 OR 12 GROMMETS)• 288”W X 60”D X 28”H (0, 8 OR 12 GROMMETS)
CONSTRUCTION AND DETAILS:
• LAMINATE TOP• TAPERED EDGE HAS SOFT TOUCH PAINTED UNDERSIDE• LEGS ARE SOLID WOOD WITH PAINTED STEEL BRACKETS• AVAILABLE WITH CORD SET, HARDWIRED OR LINKABLE
POWER WITH SURFACE ACCESS OUTLETS
62© 2020 Knoll Inc.
CT1 – Conference Table, HPL: Knoll Rockwell Unscripted –Sawhorse Tables
AVAILABLE DIMENSIONS:
• 72”W X 36””D X 28”H (0 OR 2 GROMMETS)• 84”W X 42”D X 28”H (0 OR 2 GROMMETS)• 96”W X 48”D X 28”H (0 OR 2 GROMMETS)• 108”W X 54”D X 28”H (0 OR 2 GROMMETS)• 144”W X 42/48/54”D X 28”H (0 OR 3 GROMMETS)• 192”W X 42/48/54”D X 28”H (0 OR 4 GROMMETS)• 240”W X 42/48/54”D X 28”H (0 OR 5 GROMMETS)• 288”W X 42/48/54”D X 28”H (0 OR 6 GROMMETS)• ROUND: 36”/42”/48”/54”/60”/72”/84” DIAMETER (0 OR 1 GROMMETS)
CONSTRUCTION AND DETAILS:
• LAMINATE TOP – EASY OR TAPERED• EASY TOPS AVAILABLE WITH FLAT OR BULLNOSE ABS EDGE• TAPERED TOP HAS SOFT-TOUCH PAINTED UNDERSIDE• LEGS ARE SOLID WOOD WITH PAINTED STEEL BRACKETS• AVAILABLE WITH CORD SET, HARDWIRED OR LINKABLE POWER
WITH SURFACE ACCES OUTLETS.
63© 2020 Knoll Inc.
CT2 – Conference Table, Veneer:
› A variety of top sizes to include 36” – 240” Long 30”- 60” Deep› A variety of shapes to include but not limited to, round, rectangle, boat, Racetrack, and Arc
Rectangle,› A variety of wood species and finishes to choose from including gloss or matt finish options.› Stone, glass, and or Solid Surface Material top option.› A variety of edge details to include but not limited to, reverse taper, Knife, Bullnose, Radius,
Double Flute, and Beveled.› Power/USB/data/voice port options with the option of grommet hole(s) and cover, Power Island,
troughs, or power cove(s).› Power options to be corded or hardwired.› Wire management underneath conference table through bases and wire channels to conceal
cables.› A variety of bases to include metal, wood, and powder coated.› Variety of type to include open leg, panel, cylinder, pillar in traditional, transitional and
contemporary styles.› Leveling glides for carpet or hard floor› Options: › Casters› Coordinating Storage Credenza and Tower options
64© 2020 Knoll Inc.
CT2 – Conference Table, Veneer : Knoll Reff Conference Worksurface with Drum Base
AVAILABLE DIMENSIONS:
SQUARE: • 36” X 26-1/2”H• 42” X 26-1/2”H• 48” X 26-1/2”H• 60” X 26-1/2”H• 72” X 26-1/2”H
RECTANGULAR: • 72”W X 30/36”D X 26-1/2”H• 84”W X 30/36/42”D X 26-1/2”H• 96”W X 30/36/42”D X 26-1/2”H• 120”W X 30/36/42”D X 26-1/2”H• 144”W X 42/48””D X 26-1/2”H• 168”W X 42/48””D X 26-1/2”H• 196”W X 42/48””D X 26-1/2”H
EDGE OPTIONS:
RACETRACK: • 72”W X 30/36”D X 26-1/2”H• 84”W X 30/36/42”D X 26-1/2”H• 96”W X 30/36/42”D X 26-1/2”H• 120”W X 30/36/42”D X 26-1/2”H• 144”W X 42/48””D X 26-1/2”H• 168”W X 42/48””D X 26-1/2”H• 196”W X 42/48””D X 26-1/2”H
ROUND: • 36”DIA.X 26-1/2”H• 42”DIA.X 26-1/2”H• 48”DIA.X 26-1/2”H• 60”DIA.X 26-1/2”H• 72”DIA.X 26-1/2”H
65© 2020 Knoll Inc.
CT2 – Conference Table, Veneer : Knoll Rockwell Unscripted – Library Tables
AVAILABLE DIMENSIONS:
• 144”W X 60”D X 28”H (0 OR 6 GROMMETS)• 192”W X 60”D X 28”H (0 OR 8 GROMMETS)• 240”W X 60”D X 28”H (0, 8 OR 12 GROMMETS)• 288”W X 60”D X 28”H (0, 8 OR 12 GROMMETS)
CONSTRUCTION AND DETAILS:
• LAMINATE TOP• TAPERED EDGE HAS SOFT TOUCH PAINTED UNDERSIDE• LEGS ARE SOLID WOOD WITH PAINTED STEEL BRACKETS• AVAILABLE WITH CORD SET, HARDWIRED OR LINKABLE
POWER WITH SURFACE ACCESS OUTLETS
66© 2020 Knoll Inc.
CT2 – Conference Table, Veneer: Knoll Rockwell Unscripted – Sawhorse Tables
AVAILABLE DIMENSIONS:
• 72”W X 36””D X 28”H (0 OR 2 GROMMETS)• 84”W X 42”D X 28”H (0 OR 2 GROMMETS)• 96”W X 48”D X 28”H (0 OR 2 GROMMETS)• 108”W X 54”D X 28”H (0 OR 2 GROMMETS)• 144”W X 42/48/54”D X 28”H (0 OR 3 GROMMETS)• 192”W X 42/48/54”D X 28”H (0 OR 4 GROMMETS)• 240”W X 42/48/54”D X 28”H (0 OR 5 GROMMETS)• 288”W X 42/48/54”D X 28”H (0 OR 6 GROMMETS)• ROUND: 36”/42”/48”/54”/60”/72”/84” DIAMETER (0 OR 1 GROMMETS)
CONSTRUCTION AND DETAILS:
• LAMINATE TOP – EASY OR TAPERED• EASY TOPS AVAILABLE WITH FLAT OR BULLNOSE ABS EDGE• TAPERED TOP HAS SOFT-TOUCH PAINTED UNDERSIDE• LEGS ARE SOLID WOOD WITH PAINTED STEEL BRACKETS• AVAILABLE WITH CORD SET, HARDWIRED OR LINKABLE POWER
WITH SURFACE ACCES OUTLETS.
67© 2020 Knoll Inc.
CT2 – Conference Table, Veneer: Knoll DatesWeiser –Highline Collection
PENDINGAPPROVAL
AVAILABLE DIMENSIONS:
RECTANGULAR: • 72”W X 42/48”D X 28”H • 84”W X 42/48”D X 28”H • 96”W X 48/54/60/72”D X 28”H • 108”W X 48/54/60/72”D X 28”H • 120”W X 48/54/60/72”D X 28”H • 132”W X 48/54/60/72”D X 28”H • 144”W X 48/54/60/72”D X 28”H • 156”W X 48/54/60/72”D X 28”H • 168”W X 48/54/60/72”D X 28”H • 180”W X 48/54/60/72”D X 28”H • 192”W X 48/54/60/72”D X 28”H • 204”W X 48/54/60/72”D X 28”H • 216”W X 48/54/60/72”D X 28”H • 228”W X 48/54/60/72”D X 28”H • 240”W X 48/54/60/72”D X 28”H
ELLIPTICAL: • 96”W X 48”D X 28”H• 108”W X 48”D X 28”H • 120”W X 48”D X 28”H • 132”W X 60”D X 28”H • 144”W X 60”D X 28”H • 156”W X 60”D X 28”H• 168”W X 60”D X 28”H• 180”W X 72”D X 28”H• 192”W X 72”D X 28”H• 204”W X 72”D X 28”H• 216”W X 72”D X 28”H• 228”W X 72”D X 28”H• 240”W X 72”D X 28”H
BOAT SHAPED: • 96”W X 48”D X 28”H• 108”W X 48”D X 28”H • 120”W X 48/60”D X 28”H • 132”W X 60”D X 28”H • 144”W X 60”D X 28”H • 156”W X 60”D X 28”H• 168”W X 60”D X 28”H• 180”W X 72”D X 28”H• 192”W X 72”D X 28”H• 204”W X 72”D X 28”H• 216”W X 72”D X 28”H• 228”W X 72”D X 28”H• 240”W X 72”D X 28”H
68© 2020 Knoll Inc.
CT2 – Conference Table, Veneer: Knoll DatesWeiser –Highline Collection – continued.
PENDINGAPPROVAL
AVAILABLE DIMENSIONS CONT.:
TRAPEZOID: • 84”W X 48”D X 28”H • 96”W X 48”D X 28”H • 108”W X 48”D X 28”H • 120”W X 60”D X 28”H • 132”W X 60”D X 28”H • 144”W X 60”D X 28”H • 156”W X 60”D X 28”H • 168”W X 60”D X 28”H • 180”W X 72”D X 28”H • 192”W X 72”D X 28”H • 204”W X 72”D X 28”H • 216”W X 72”D X 28”H • 228”W X 72”D X 28”H • 240”W X 72”D X 28”H
ROUND: • 42”DIA. X 28”H• 48”DIA. X 28”H• 60”DIA. X 28”H• 72”DIA. X 28”H
SQUARE:• 42” X 28”H• 48” X 28”H• 60” X 28”H• 72” X 28”H
EDGE DETAIL:
69© 2020 Knoll Inc. 69© 2020 Knoll Inc.
Credenzas
70© 2020 Knoll Inc.
CR1 – Storage Credenzas, HPL:
› Variety of sizes including 36” -90”W, x 20”-30”D x 29- 36”H› A variety of edge details to include but not limited to Square, Knife, Bevel Radius and Bullnose› Design matches conference table› Hinged door(s) and sliding door(s) option.› Locks required› Adjustable shelves in 1” increments. › A minimum 12 year warrantyOptions: › Pulls and knob options for doors and drawers.› Frosted Glass/Acrylic Door option. Glass to be tempered.› Drawer storage option. › Option with vented cabinet for media› Worksurface Grommet option
71© 2020 Knoll Inc.
CR1 – Storage Credenzas, HPL: Knoll Reff
THIS STANDARD INCLUDES:
78”W X 20”D X 34-3/8”H LAMINATE CREDENZA OPEN PEDESTAL CENTERHINGED DOOR LEFT, WASTE/RECYCLE PEDESTAL RIGHT
72© 2020 Knoll Inc.
CR1 – Storage Credenzas, HPL: Knoll Rockwell Unscripted
THIS STANDARD INCLUDES:
60”W CREDENZA WITH WIRE BASELAMINATE CASE AND DOOR FINISHHINGED DOORS WITH OPENING ON RIGHT END
73© 2020 Knoll Inc.
CR1 – Storage Credenzas, HPL: Knoll Rockwell Unscripted
THIS STANDARD INCLUDES:
48”W CREDENZA WITH UPRIGHTSGLIDESLAMINATE CASE OPEN CASE FRONT
74© 2020 Knoll Inc.
CR1 – Storage Credenzas, HPL: Knoll DatesWeiser
AVAILABLE DIMENSIONS:
1H CREDENZAS• 64”W X 22/24”D X 29.25H• 76”W X 22/24”D X 29.25H• 87”W X 22/24”D X 29.25H• 99”W X 22/24”D X 29.25H
CONSTRUCTION AND DETAILS:
• EXPOSED, OPEN METAL LEGS COORDINATE WITH LIGHLINE TABLE COLLECTION• CASES AVAILABLE IN ONE, TWO AND THREE LEVELS TO APPROPRIATELY SCALE
ESSENTIAL NEEDS FOR STORAGE. • OFFERED WITH SEVERAL TOP OPTIONS, PULL OUT TRASH AND RECYCLING, COOL
DRAWERS AND A/V ACCOMMODATIONS TO MEET SPECIFIC REQUIREMENTS.
PENDINGAPPROVAL
75© 2020 Knoll Inc.
CR2 – Storage Credenzas, Veneer:
› Variety of sizes including 36” -90”W, x 20”-30”D x 29- 36”H› A variety of edge details to include but not limited to Square, Knife, Bevel Radius and Bullnose› Design matches conference table› Hinged door(s) and sliding door(s) option.› Locks required› Pulls and knob options for doors and drawers.› Adjustable shelves in 1” increments. › Frosted Glass/Acrylic Door option. Glass to be tempered.› A minimum 12 year warrantyOptions: › Drawer storage option. › Option with vented cabinet for media› Worksurface Grommet option
76© 2020 Knoll Inc.
CR2 – Storage Credenzas, Veneer: Knoll Reff
THIS STANDARD INCLUDES:
78”W X 20”D X 28-3/8”H VENEER CREDENZA BOX/FILE CENTERHINGED DOOR LEFT AND RIGHT
77© 2020 Knoll Inc.
CR2 – Storage Credenzas, Veneer: Knoll Reff
THIS STANDARD INCLUDES:
84”W X 20”D X 28-3/8”H VENEER CREDENZA BOX/BOX/FILE CENTERWASTE/RECYCLE PEDESTAL LEFT, HINGED DOOR PEDESTAL RIGHT
78© 2020 Knoll Inc.
CR2 – Storage Credenzas, Veneer: Knoll Rockwell Unscripted
THIS STANDARD INCLUDES:
48”W CREDENZA WITH WIRE BASEVENEER CASE AND DOOR FINISHALL HINGED DOORS
79© 2020 Knoll Inc.
CR2 – Storage Credenzas, Veneer: Knoll Rockwell Unscripted
THIS STANDARD INCLUDES:
60”W CREDENZA WITH UPRIGHTSCASTERSVENEER CASE AND DOOR FINISH4 HINGED DOORS WITH OPEN LEFT
80© 2020 Knoll Inc.
CR2 – Storage Credenzas, Veneer: Knoll DatesWeiser –Highline Collection
PENDINGAPPROVAL
AVAILABLE DIMENSIONS:
1H CREDENZAS• 64”W X 22/24”D X 29.25H• 76”W X 22/24”D X 29.25H• 87”W X 22/24”D X 29.25H• 99”W X 22/24”D X 29.25H
2H CREDENZAS• 64”W X 22/24”D X 29.25H• 76”W X 22/24”D X 29.25H• 87”W X 22/24”D X 29.25H• 99”W X 22/24”D X 29.25H
3H CREDENZAS• 64”W X 22/24”D X 33.125H• 76”W X 22/24”D X 33.125H• 87”W X 22/24”D X 33.125H• 99”W X 22/24”D X 33.125H
CONSTRUCTION AND DETAILS:
• EXPOSED, OPEN METAL LEGS COORDINATE WITH LIGHLINE TABLE COLLECTION• CASES AVAILABLE IN ONE, TWO AND THREE LEVELS TO APPROPRIATELY SCALE
ESSENTIAL NEEDS FOR STORAGE. • OFFERED WITH SEVERAL TOP OPTIONS, PULL OUT TRASH AND RECYCLING, COOL
DRAWERS AND A/V ACCOMMODATIONS TO MEET SPECIFIC REQUIREMENTS.
81© 2020 Knoll Inc. 81© 2020 Knoll Inc.
Training Tables
82© 2020 Knoll Inc.
83© 2020 Knoll Inc.
TT1 – Training Table, Reconfigurable, Multiple Shapes, HPL:
› Variety of sizes 42”-96”W x 18”-36”D› Laminate Edge details to include but not limited to, T- molding, Urethane, 3mm Wood, Square
Wood, Bullnose wood, and fluted.› Leg and modesty panel finish in powder coat.› One sided mechanism release for tilt and nest operation.› Grommet holes and covers for wire management.› Integrated wire management into the leg.› Dual wheel-locking casters.› Linking/Ganging capability to connect rows of tables for training and prevents sequenced power
from becoming disconnected.Options: › Modesty panel options to include laminate, acrylic or glazing.› Flip/nest options› Glide options.› Wheelchair Height 32” option› Modular power from table to table allowing end user reconfiguration› Power and Voice/Data options.› Tops to have embedded wireless charging technology as an option.
84© 2020 Knoll Inc.
TT1 – Training Table, Reconfigurable, Multiple Shapes, HPL:Knoll Studio – Propeller Rectangular and Square Tables
AVAILABLE OPTIONS:
AVAILABLE DIMENSIONS:
• 48”W X 18/24/30/36”D X 28 3/4”H• 60”W X 18/24/30/36”D X 28 3/4”H• 72”W X 18/24/30”D X 28 3/4”H
FEATURES:
• INTEGRATED WIREMANAGMENT TROUGH• INTEGRAL GANGING BRACKET ALLOWS THE
TABLE TO BE GANGED ON ALL FOUR SIDES; IT ALSO ACTS AS A LEVELER
• A SIMPLE FLIP MECHANISM MAKES STORAGE EASY
• SINGLE HANDED FLIP AND EASY NESTING• WEDGE TOP AVAILABLE TO CREATE L, U
AND HOLLOW SHAPE CONFIGURATIONS
85© 2020 Knoll Inc.
TT1 – Training Table, Reconfigurable, Multiple Shapes, HPL:Knoll Studio – Pixel (C-Leg) A-Series
THIS STANDARD INCLUDES:
WORK HEIGHTFLIP TOPCASTERSLAMINATE TOP*LAMINATE MODESTY SCREEN AVAILABLE
AVAILABLE DIMENSIONS:
• 48”W X 18/24/30”D X 28 3/4”H• 60”W X 18/24/30”D X 28 3/4”H• 72”W X 18/24/30”D X 28 3/4”H
FEATURES:
• INTEGRATED WIREMANAGMENT TROUGH• INTEGRAL GANGING BRACKET ALLOWS THE
TABLE TO BE GANGED ON ALL FOUR SIDES; IT ALSO ACTS AS A LEVELER
• A SIMPLE FLIP MECHANISM MAKES STORAGE EASY
• SINGLE HANDED FLIP AND EASY NESTING• WEDGE TOP AVAILABLE TO CREATE L, U
AND HOLLOW SHAPE CONFIGURATIONS
PENDINGAPPROVAL
86© 2020 Knoll Inc.
TT1 – Training Table, Reconfigurable, Multiple Shapes, HPL:Knoll Studio – Pixel (T-Leg)
THIS STANDARD INCLUDES:
WORK HEIGHTFLIP TOPCASTERSLAMINATE TOP*LAMINATE MODESTY SCREEN AVAILABLE
AVAILABLE DIMENSIONS:
• 48”W X 18/24/30”D X 28 3/4”H• 60”W X 18/24/30”D X 28 3/4”H• 72”W X 18/24/30”D X 28 3/4”H
FEATURES:
• T-LEG ALLOWS 2-SIDED TABLE THAT IS EXCELLENT FOR DESKING AND COLLABORATIVE MEETINGS. FEATURES PIVOTING LEG THAT ALLOWS FOR STRAIGHT NESTING.
• INTEGRAL GANGING BRACKET ALLOWS THE TABLE TO BE GANGED ON ALL FOUR SIDES; IT ALSO ACTS AS A LEVELER
• FLIP DOOR ACCESS TO TROUGH PROVIDES HORIZONTAL WIRE MANAGEMENT
• WEDGE TOP AVAILABLE TO CREATE L, U AND HOLLOW SHAPE CONFIGURATIONS
87© 2020 Knoll Inc.
TT1 – Training Table, Reconfigurable, Multiple Shapes, HPL:Knoll Studio – Pixel (T-Leg) Trapezoid
THIS STANDARD INCLUDES:
WORK HEIGHTFLIP TOPCASTERSLAMINATE TOP*LAMINATE MODESTY SCREEN AVAILABLE
AVAILABLE DIMENSIONS:
• 48”W X 24”D X 28 3/4”H• 60”W X 24/30”D X 28 3/4”H
FEATURES:
• INTEGRAL GANGING BRACKET ALLOWS THE TABLE TO BE GANGED ON ALL FOUR SIDES; IT ALSO ACTS AS A LEVELER
• SINGLE HANDED FLIP AND EASY NESTING• FLIP DOOR ACCESS TO TROUGH PROVIDES
HORIZONTAL WIRE MANAGEMENT
88© 2020 Knoll Inc.
TT2 – Training Table, Reconfigurable, Multiple Shapes, Veneer Wood:
› Variety of sizes 42”-96”W x 18”-36”D› Wood Veneer Edge details to include but not limited to Flat, square, bullnose, or fluted› Leg and modesty panel steel finish in powder coat or frosted acrylic panel.› One sided mechanism release for tilt and nest operation.› Grommet holes and covers for wire management.› Integrated wire management into the leg.› Dual wheel-locking casters.› Linking/Ganging capability to connect rows of tables for training and prevents sequenced power
from becoming disconnected.Options: › Modesty panel options› Flip/nest options› Glide options.› Wheelchair Height 32” option› Modular power from table to table allowing end user reconfiguration› Power and Voice/Data options.
89© 2020 Knoll Inc.
TT2 – Training Table, Reconfigurable, Multiple Shapes, Venner Wood: Knoll Studio – Propeller Rectangular and Square Tables
AVAILABLE OPTIONS:
AVAILABLE DIMENSIONS:
• 48”W X 18/24/30/36”D X 28 3/4”H• 60”W X 18/24/30/36”D X 28 3/4”H• 72”W X 18/24/30”D X 28 3/4”H
FEATURES:
• INTEGRATED WIREMANAGMENT TROUGH• INTEGRAL GANGING BRACKET ALLOWS THE
TABLE TO BE GANGED ON ALL FOUR SIDES; IT ALSO ACTS AS A LEVELER
• A SIMPLE FLIP MECHANISM MAKES STORAGE EASY
• SINGLE HANDED FLIP AND EASY NESTING• WEDGE TOP AVAILABLE TO CREATE L, U
AND HOLLOW SHAPE CONFIGURATIONS
90© 2020 Knoll Inc.
TT2 – Training Table, Reconfigurable, Multiple Shapes, Venner Wood: Knoll Studio – Pixel (C-Leg) A-Series
THIS STANDARD INCLUDES:
WORK HEIGHTFLIP TOPCASTERSVENEER TOP
AVAILABLE DIMENSIONS:
• 48”W X 18/24/30”D X 28 3/4”H• 60”W X 18/24/30”D X 28 3/4”H• 72”W X 18/24/30”D X 28 3/4”H
FEATURES:
• INTEGRATED WIREMANAGMENT TROUGH• INTEGRAL GANGING BRACKET ALLOWS THE
TABLE TO BE GANGED ON ALL FOUR SIDES; IT ALSO ACTS AS A LEVELER
• A SIMPLE FLIP MECHANISM MAKES STORAGE EASY
• SINGLE HANDED FLIP AND EASY NESTING• WEDGE TOP AVAILABLE TO CREATE L, U
AND HOLLOW SHAPE CONFIGURATIONS
PENDINGAPPROVAL
91© 2020 Knoll Inc.
TT2 – Training Table, Reconfigurable, Multiple Shapes, Venner Wood: Knoll Studio – Pixel (T-Leg)
THIS STANDARD INCLUDES:
WORK HEIGHTFLIP TOPCASTERSVENEER TOP
AVAILABLE DIMENSIONS:
• 48”W X 18/24/30”D X 28 3/4”H• 60”W X 18/24/30”D X 28 3/4”H• 72”W X 18/24/30”D X 28 3/4”H
FEATURES:
• T-LEG ALLOWS 2-SIDED TABLE THAT IS EXCELLENT FOR DESKING AND COLLABORATIVE MEETINGS. FEATURES PIVOTING LEG THAT ALLOWS FOR STRAIGHT NESTING.
• INTEGRAL GANGING BRACKET ALLOWS THE TABLE TO BE GANGED ON ALL FOUR SIDES; IT ALSO ACTS AS A LEVELER
• FLIP DOOR ACCESS TO TROUGH PROVIDES HORIZONTAL WIRE MANAGEMENT
• WEDGE TOP AVAILABLE TO CREATE L, U AND HOLLOW SHAPE CONFIGURATIONS
92© 2020 Knoll Inc.
TT2 – Training Table, Reconfigurable, Multiple Shapes, Venner Wood: Knoll Studio – Pixel (T-Leg) Trapezoid
THIS STANDARD INCLUDES:
WORK HEIGHTFLIP TOPCASTERSVENEER TOP
AVAILABLE DIMENSIONS:
• 48”W X 24”D X 28 3/4”H• 60”W X 24/30”D X 28 3/4”H
FEATURES:
• INTEGRAL GANGING BRACKET ALLOWS THE TABLE TO BE GANGED ON ALL FOUR SIDES; IT ALSO ACTS AS A LEVELER
• SINGLE HANDED FLIP AND EASY NESTING• FLIP DOOR ACCESS TO TROUGH PROVIDES
HORIZONTAL WIRE MANAGEMENT
93© 2020 Knoll Inc.
HAW3 – Height Adjustable Work Table, sit to stand, Electric, HPL:
› Available in 24”-30”D x 36”-140” W in the rectangle configuration.› A variety of shapes including rectangular, 90 degree, 120 degree corner configurations› 25” – 50” +/- 2” electric height adjustability range › Minimum of 220 lbs. distributed load bearing capacity per table.› Lifting columns controlled by “master” and “slave” motors via a single switch.› Electrical – 120V, 60Hz, Single phase, 10% duty cycle. Maximum draw 4 amps under full load,
idle current is typically 20mA› All assemblies meet or exceed ANSI/BIFMA standards› Worksurface to allow work tools to be attached.› 3-stage synchronized lifting columns with integral shrouding.› Push button height adjustability› Glides have .5” of height adjustment for surface leveling on uneven floors. Glides to not scratch or
mar flooring either carpet or hard flooring.› Worksurface finish to be HPL› Edge of table top to include but not limited to T-mold and square option.› Wire management is available› A rigid design to maximize floor space without sacrificing stability.› Full clearance under the worksurface.› Electronics are certified by TUV to UL-73 and CSA C22.2› Provide trough to manage wires› 6'-0” minimum power cord
94© 2020 Knoll Inc.
HAW3 – Height Adjustable Work Table, sit to stand, Electric, HPL: k.stand
THIS TYPICAL INCLUDES:
(1) k.stand HEIGHT ADJUSTABLE CORNER TABLE BASE WITH STANDARD ELECTRIC(1) 57”WX30”D ANTENNA WORKSURFACE WITH 47” RETURN(1) MOBILE BOX/FILE PEDESTAL(1) TASK CHAIR – REGENERATION, SEE TS1(2) ANTENNA FABRIC DESK SCREEN FOR 42” HIGH HORIZON
PENDINGAPPROVAL
95© 2020 Knoll Inc.
HAW3 – Height Adjustable Work Table, sit to stand, Electric, HPL: k.stand
THIS TYPICAL INCLUDES:
(2) k.stand HEIGHT ADJUSTABLE TABLE BASE WITH 52”W X 23”D DIVIDENDS WORKSURFACE (2) 12”W X 23”D X 42”H ANCHOR LOCKER (1) LIGHT TASK CHAIR – OLLO, SEE GC1(2) ANTENNA LAMINATE DESK SCREEN FOR 42” HIGH HORIZON
PENDINGAPPROVAL
96© 2020 Knoll Inc.
HAW3 – Height Adjustable Work Table, sit to stand, Electric, HPL: Tone
THIS TYPICAL INCLUDES:
(2) TONE ELECTRIC HEIGHT ADJUSTABLE 90DEGREE CORNER BASE WITH ANTENNA TOP
(2) 15”W X 24”D X 42”H QUOIN LOCKER (1) TASK CHAIR – REGENERATION, SEE TS1(2) ANTENNA MARKERBOARD DESK SCREEN FOR
42” HIGH HORIZON(2) 36”W LOAD BAR WITH WORKSURFACE
BRACKET, SLANTED PAPER SORTER, PENCIL CUP – SEE DA1
PENDINGAPPROVAL
97© 2020 Knoll Inc.
HAW3 – Height Adjustable Work Table, sit to stand, Electric, HPL – JSN E0032 (Knoll - Tone)
THIS STANDARD INCLUDES:
1 FREESTANDING WORKSURFACE1 TOOL RAIL2 PAPER TRAY1 DIAGONAL TRAY1 ADJUSTABLE KEYBOARD TRAY1 MOBILE PEDESTAL, BOX/FILE
98© 2020 Knoll Inc.
HAW3 – Height Adjustable Work Table, sit to stand, Electric, HPL – JSN E0045 (Knoll - Tone)
THIS STANDARD INCLUDES:
1 FREESTANDING WORKSURFACE1 TOOL RAIL2 PAPER TRAY1 DIAGONAL TRAY1 ADJUSTABLE KEYBOARD TRAY1 MOBILE PEDESTAL, BOX/FILE
99© 2020 Knoll Inc.
HAW3 – Height Adjustable Work Table, sit to stand, Electric, HPL – JSN E0048 (Knoll - Tone)
THIS STANDARD INCLUDES:
1 FREESTANDING WORKSURFACE1 TOOL RAIL2 PAPER TRAY1 DIAGONAL TRAY1 ADJUSTABLE KEYBOARD TRAY1 MOBILE PEDESTAL, BOX/FILE
100© 2020 Knoll Inc. 100© 2020 Knoll Inc.
Seating
101© 2020 Knoll Inc.
102© 2020 Knoll Inc.
TS1 – 24/7 Ergonomic Heavy Duty Task with Bariatric version in similar style:
› Weight capacity shall be a minimum of 300 lbs. with steel reinforced seats and heavy duty gas cylinder
› Metal five star base with carpet castersAdjustments: › Independent lumbar support.› Seat depth slider adjustment up to 3”› Back: recline angle, tilt tention, and forward tilt stop› Seat: depth, tilt, and pneumatic height › Arms: post width, height, width, arm pad 360 degreesOptions: › Headrest with independent positioning› Extended height range cylinders from 14” to 22”› Choice of two back size options with built-in lumbar support› Multiple caster options for hard surface, soft surface, rubber flooring or a multi-function caster for
varying floor types.› Multiple seat styles to include, mesh, plastic, or multi-density foam cushion, with waterfall front› Chrome 5 star base› Textile options ranging from fabric to vinyl to include COM/Healthcare grade fabric and the ability
to clean using germicide or bleach solution› Back height adjustment option
103© 2020 Knoll Inc.
TS1 – 24/7 Ergonomic Heavy Duty Task with Bariatric version in similar style: Knoll Generation
THIS STANDARD INCLUDES:
FLEX BACK NETHIGH PERFORMANCE ARMSPOLISHED ALUMINUM BASESTANDARD CYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
• NO ONE RIGHT WAY TO SIT – GENERATION CHAIR SUPPORTS NATURAL TENDANCY TO MOVE.
• MATERIAL AND DESIGN INNOVATION – ELASTIC DESIGN, PRODUCT REARRANGES ITSELF IN RESPONSE TO USER
• COMFORT AND UNRESTRAINED MOVEMENT –HIGHLIGHTS KNOLLS HOLISTIC APPROACH TO ERGONOMICS, PROVIDING SEATING THAT MEETS ERGONOMIC STANDARDS WHILE INNOVATING SUPPORT THE NEED OF TODAY’S WORKERS TO SEAMLESSLY TRANSITION BETWEEN WORK MODES.
WHAT MAKES GENERATION SPECIAL
104© 2020 Knoll Inc.
TS1 – 24/7 Ergonomic Heavy Duty Task with Bariatric version in similar style: Knoll ReGeneration
THIS STANDARD INCLUDES:
FLEX BACK NETHIGH PERFORMANCE ARMSPOLISHED ALUMINUM BASESTANDARD CYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
• INNOVATIVE IN IT’S SIMPLICITY – PAIRS DOWN THE CHAIRS ESSENCE WHILE REMAINING TRUE TO THE SPIRIT OF THE GENERATION, TO LET YOU SIT HOW YOU WANT.
• COMFORT AND FREEDOM OF MOVEMENT –SUPPORTS USER FOR EVERYDAY WORK AND ALLOWS FOR 270 DEGREES OF SITTING.
• SUSTAINABLY EFFICIENT – CONTINUOUSLY EVOLVES ITS SUSTAINABLE PRACTICES WITH JUST SEVEN MAJOR PARTS.
WHAT MAKES REGENERATION SPECIAL
105© 2020 Knoll Inc.
TS1 – 24/7 Ergonomic Heavy Duty Task with Bariatric version in similar style: Knoll Life
THIS STANDARD INCLUDES:
HIGH PERFORMANCE ARMSSTANDARD ARMPADPOLISHED ALUMINUM BASESTANDARD HEIGHTCYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
• THOUGHTFUL DESIGN – RESEARCH BASED DESIGN WITH ATTENTION TO DETAIL AND QUALITY.
• COMFORT THROUGH SYNCHRONIZED RECLINE AND AUTO-BALANCED TENSION.
• CHOICE – IN COLOR PALETTE, TEXTILES, ARM OPTIONS, BASE FINISH AND CASTERS.
WHAT MAKES LIFE SPECIAL
106© 2020 Knoll Inc.
TS1 – 24/7 Ergonomic Heavy Duty Task with Bariatric version in similar style: Knoll Remix
THIS STANDARD INCLUDES:
HIGH PERFORMANCE ARMSPOLISHED ALUMINUM BASESTANDARD CYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
• UNEXPECTED PERFORMANCE – COMBINES TRADITIONAL AND INNOVATIVE ELEMENTS, RESULTING IN A NEW PERFORMANCE FOR AN UPHOLSTERED WORK CHAIR.
• REDEFINED COMFORT – FLEX NET MATRIX IS DESIGNED TO PROVIDE FIRMER SUPPORT IN THE LUMBAR AND SHOULDER REGION WHILE FULLY UPHOLSTERED PERIMETER OFFERS SOFT, UNINTERRUPTED COMFORT.
• TRANSITIONAL APPEAL – UNCONVENTIONAL MIX OF MATERIALS DRAWS ALL USERS TO DESIGN.
WHAT MAKES REMIX SPECIAL
107© 2020 Knoll Inc.
TS2 – Multiple-Position Task Chair:
› Flexible Back: High Performance Elastomer or equal material› Weight capacity shall be a minimum of 300 lbs.› Metal five star base with carpet castersAdjustments: › Independent lumbar support w/ height and depth adjustability› Seat depth slider adjustment up to 3”› Back: height and angle› Seat: pneumatic height, synchronized back to seat recline angle, tilt tension, forward tilt stop› Arms: post width, height, width, arm pad 360 degreesOptions: › Extended height range cylinders from 14” to 22”› Choice of two back size options with built-in lumbar support› Multiple caster options for hard surface, soft surface, rubber flooring or a multi-function caster for
varying floor types.› Multiple seat styles to include, mesh, plastic, or multi-density foam cushion, with waterfall front› Chrome 5 star base› Textile options ranging from fabric to vinyl to include COM/Healthcare grade fabric and the ability
to clean using germicide or bleach solution› Moisture barrier fabric backing or barrier wrapped foam
108© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
FLEX BACK NETHIGH PERFORMANCE ARMSPOLISHED ALUMINUM BASESTANDARD CYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
TS2 – Multiple-Position Task Chair: Knoll Generation
• NO ONE RIGHT WAY TO SIT – GENERATION CHAIR SUPPORTS NATURAL TENDANCY TO MOVE.
• MATERIAL AND DESIGN INNOVATION – ELASTIC DESIGN, PRODUCT REARRANGES ITSELF IN RESPONSE TO USER
• COMFORT AND UNRESTRAINED MOVEMENT –HIGHLIGHTS KNOLLS HOLISTIC APPROACH TO ERGONOMICS, PROVIDING SEATING THAT MEETS ERGONOMIC STANDARDS WHILE INNOVATING SUPPORT THE NEED OF TODAY’S WORKERS TO SEAMLESSLY TRANSITION BETWEEN WORK MODES.
WHAT MAKES GENERATION SPECIAL
109© 2020 Knoll Inc.
TS2 – Multiple-Position Task Chair: Knoll ReGeneration
THIS STANDARD INCLUDES:
FLEX BACK NETHIGH PERFORMANCE ARMSPOLISHED ALUMINUM BASESTANDARD CYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
• INNOVATIVE IN IT’S SIMPLICITY – PAIRS DOWN THE CHAIRS ESSENCE WHILE REMAINING TRUE TO THE SPIRIT OF THE GENERATION, TO LET YOU SIT HOW YOU WANT.
• COMFORT AND FREEDOM OF MOVEMENT –SUPPORTS USER FOR EVERYDAY WORK AND ALLOWS FOR 270 DEGREES OF SITTING.
• SUSTAINABLY EFFICIENT – CONTINUOUSLY EVOLVES ITS SUSTAINABLE PRACTICES WITH JUST SEVEN MAJOR PARTS.
WHAT MAKES REGENERATION SPECIAL
110© 2020 Knoll Inc.
TS2 – Multiple-Position Task Chair: Knoll Remix
THIS STANDARD INCLUDES:
HIGH PERFORMANCE ARMSPOLISHED ALUMINUM BASESTANDARD CYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
• UNEXPECTED PERFORMANCE – COMBINES TRADITIONAL AND INNOVATIVE ELEMENTS, RESULTING IN A NEW PERFORMANCE FOR AN UPHOLSTERED WORK CHAIR.
• REDEFINED COMFORT – FLEX NET MATRIX IS DESIGNED TO PROVIDE FIRMER SUPPORT IN THE LUMBAR AND SHOULDER REGION WHILE FULLY UPHOLSTERED PERIMETER OFFERS SOFT, UNINTERRUPTED COMFORT.
• TRANSITIONAL APPEAL – UNCONVENTIONAL MIX OF MATERIALS DRAWS ALL USERS TO DESIGN.
WHAT MAKES REMIX SPECIAL
111© 2020 Knoll Inc.
TS4 – Ergonomic Task Chair w/ counter height:
› Weight capacity shall be a minimum of 300 lbs.› Metal five star base with carpet castersAdjustments: › Independent lumbar support w/ height and depth adjustability› Adjustable seat depth› Pneumatic adjustable height› Synchronized back to seat recline angle, with tilt tension, forward tilt stop› Arm adjustments to include post width, height, arm pad width, arm pad pivot of 360 degrees› 24-27” seat height with foot ringOptions: › Choice of two back size options with built-in lumbar support› Multiple caster options for hard surface, soft surface, rubber flooring or a multi-function caster for
varying floor types› Multiple seat materials to include, mesh, plastic, or multi-density foam cushion seat with waterfall
front› Chrome 5 star base› Textile options ranging from fabric to vinyl to include COM/Healthcare grade fabric and the ability
to clean using germicide or bleach solution› Moisture barrier fabric backing or barrier wrapped foam
112© 2020 Knoll Inc.
TS4 – Ergonomic Task Chair w/ counter height: Knoll ReGeneration
THIS STANDARD INCLUDES:
FLEX BACK NETHIGH PERFORMANCE ARMSPOLISHED ALUMINUM BASEHIGH TASK CYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
113© 2020 Knoll Inc.
GC1 – Basic Guest Chair:
› Built-in cleanout› Weight Capacity of a minimum of 300 lbs. steel reinforced seats› Non-marring glideOptions: › Self leveling glide› Multiple seat materials to include, mesh, plastic, or multi-density foam cushion seat› Textile options ranging from fabric to vinyl to include COM/Healthcare grade fabric and the ability
to clean using germicide or bleach solution› Moisture barrier fabric backing and barrier wrapped foam› 4-Leg chair with or without arms› Steel Tube Legs and Arms, with powder coat silver metallic finish option› Ability to stack› Wall Saver leg option
114© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
STACKING BASEARMLESSUPHOLSTERED SEAT SILVER FRAMEGLIDES
GC1 – Basic Guest Chair: Knoll MultiGeneration
PENDINGAPPROVAL
115© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
WOOD SEAT AND BACK
GC1 – Basic Guest Chair: Knoll Muuto Loft Side Chair
PENDINGAPPROVAL
116© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
FIBER SEATSLED BASE
GC1 – Basic Guest Chair: Knoll Muuto Fiber Side Chair
PENDINGAPPROVAL
117© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
FIXED ARMSSTANDARD CYLINDER5-STAR PLASTIC BASEGLIDES
GC1 – Basic Guest Chair: Knoll Ollo
PENDINGAPPROVAL
118© 2020 Knoll Inc.
GC2 – Mid-Grade Guest Chair with Bariatric Coordinate:
› Built-in cleanout› Weight Capacity of a minimum of 300 lbs. steel reinforced seatsOptions: › Multiple glide options for hard surface, soft surface, rubber flooring or multi-function for varying
floor types› Multiple seat materials to include, mesh, plastic, or multi-density foam cushion seat› Textile options ranging from fabric to vinyl to include COM/Healthcare grade fabric and the ability
to clean using germicide or bleach solution› Moisture barrier fabric backing or barrier wrapped foam› Replaceable components to include but not limited to seat cushion, back cushion, seat cover,
back cover, frame components, and arm caps› Wood or metal frame options› Available with or without arms› Ability to stack› Wall saver leg option› Optional casters for two or more legs (CLC Dining)
119© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
WOOD BACKTEXTILE SEAT PAD
GC2 – Mid-Grade Guest Chair: Knoll Muuto Loft Side Chair
PENDINGAPPROVAL
120© 2020 Knoll Inc.
GC2 – Mid-Grade Guest Chair: Knoll MultiGeneration
PENDINGAPPROVAL
THIS STANDARD INCLUDES:
5-STAR BASEFIXED ARMSUPHOLSTERED SEAT BLACK PLASTIC BASEGLIDES
121© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
WOOD BASETEXTILE SEAT
GC2 – Mid-Grade Guest Chair: Knoll Muuto Fiber Armchair
PENDINGAPPROVAL
122© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
TEXTILE SEATTUBE BASE (ABILITY TO STACK)
GC2 – Mid-Grade Guest Chair: Knoll Muuto Fiber Side Chair
PENDINGAPPROVAL
123© 2020 Knoll Inc.
CC1 – Small Conference Chairs:
› Weight Capacity of a minimum of 300 lbs. steel reinforced seats› Ergonomic back support› Metal five star base with carpet castersAdjustments: › Adjustable lumbar› Synchro tilt› Adjustable seat depth› Adjustable back tension and lock positions› Waterfall seatOptions: › Multiple glide/caster options for hard surface, soft surface, rubber flooring or multi-function for
varying floor types› Multiple seat materials to include, mesh, plastic, or multi-density foam cushion seat› Textile options ranging from fabric to vinyl to include COM/Healthcare grade fabric and the ability
to clean using germicide or bleach solution› Moisture barrier fabric backing or barrier wrapped foam› Multiple arm styles and materials› Waterfall seat› Optional chrome finish
124© 2020 Knoll Inc.
CC1 – Small Conference Chair: Knoll Generation
THIS STANDARD INCLUDES:
HEIGHT ADJUSTABLE ARMSSTANDARD ARMPADPOLISHED ALUMINUM BASESTANDARD HEIGHTCYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
• NO ONE RIGHT WAY TO SIT – GENERATION CHAIR SUPPORTS NATURAL TENDANCY TO MOVE.
• MATERIAL AND DESIGN INNOVATION – ELASTIC DESIGN, PRODUCT REARRANGES ITSELF IN RESPONSE TO USER
• COMFORT AND UNRESTRAINED MOVEMENT –HIGHLIGHTS KNOLLS HOLISTIC APPROACH TO ERGONOMICS, PROVIDING SEATING THAT MEETS ERGONOMIC STANDARDS WHILE INNOVATING SUPPORT THE NEED OF TODAY’S WORKERS TO SEAMLESSLY TRANSITION BETWEEN WORK MODES.
WHAT MAKES GENERATION SPECIAL
125© 2020 Knoll Inc.
CC1 – Small Conference Chair: Knoll Life
THIS STANDARD INCLUDES:
HEIGHT ADJUSTABLE ARMSSTANDARD ARMPADPOLISHED ALUMINUM BASESTANDARD HEIGHTCYLINDERLUMBAR SUPPORT
• THOUGHTFUL DESIGN – RESEARCH BASED DESIGN WITH ATTENTION TO DETAIL AND QUALITY.
• COMFORT THROUGH SYNCHRONIZED RECLINE AND AUTO-BALANCED TENSION.
• CHOICE – IN COLOR PALETTE, TEXTILES, ARM OPTIONS, BASE FINISH AND CASTERS.
WHAT MAKES LIFE SPECIAL
126© 2020 Knoll Inc.
CC1 – Small Conference Chair: Knoll Remix
THIS STANDARD INCLUDES:
HEIGHT ADJUSTABLE ARMSPOLISHED ALUMINUM BASESTANDARD CYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
• UNEXPECTED PERFORMANCE – COMBINES TRADITIONAL AND INNOVATIVE ELEMENTS, RESULTING IN A NEW PERFORMANCE FOR AN UPHOLSTERED WORK CHAIR.
• REDEFINED COMFORT – FLEX NET MATRIX IS DESIGNED TO PROVIDE FIRMER SUPPORT IN THE LUMBAR AND SHOULDER REGION WHILE FULLY UPHOLSTERED PERIMETER OFFERS SOFT, UNINTERRUPTED COMFORT.
• TRANSITIONAL APPEAL – UNCONVENTIONAL MIX OF MATERIALS DRAWS ALL USERS TO DESIGN.
WHAT MAKES REMIX SPECIAL
127© 2020 Knoll Inc.
CC1 – Small Conference Chair: Knoll ReGeneration
THIS STANDARD INCLUDES:
FULLY UPHOLSTERED BACKHEIGHT ADJUSTABLE ARMSPOLISHED ALUMINUM BASESTANDARD CYLINDERLUMBAR SUPPORT
PENDINGAPPROVAL
• INNOVATIVE IN IT’S SIMPLICITY – PAIRS DOWN THE CHAIRS ESSENCE WHILE REMAINING TRUE TO THE SPIRIT OF THE GENERATION, TO LET YOU SIT HOW YOU WANT.
• COMFORT AND FREEDOM OF MOVEMENT –SUPPORTS USER FOR EVERYDAY WORK AND ALLOWS FOR 270 DEGREES OF SITTING.
• SUSTAINABLY EFFICIENT – CONTINUOUSLY EVOLVES ITS SUSTAINABLE PRACTICES WITH JUST SEVEN MAJOR PARTS.
WHAT MAKES REGENERATION SPECIAL
128© 2020 Knoll Inc.
CC4 – Conference Stacker Chair with Bariatric Coordinate:
› Weight Capacity of a minimum of 300 lbs. steel reinforced seats› 4-leg caster base with carpet casters standard› Arm and armless versions› Mid to low back heightOptions: › Multiple frame materials such as polypropylene, wood, and/or metal and with multiple finish
options for each material› Multiple glide/caster options for hard surface, soft surface, rubber flooring or multi-function for
varying floor types› Multiple seat materials to include, mesh, plastic, or multi-density foam cushion seat› Textile options ranging from fabric to vinyl to include COM/Healthcare grade fabric and the ability
to clean using germicide or bleach solution› Moisture barrier fabric backing or barrier wrapped foam› Multiple arm styles and materials› Tablet Arm, left, right, or universal› Storage basket› Ganging hardware› Ability to stack› Wall saver leg option› Flex back option
129© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
FIXED ARMSUPHOLSTERED SEAT PADHARD CASTERS FOR SOFT FLOORS
CC4 – Conference Stacker Chair: Knoll MultiGeneration
PENDINGAPPROVAL
130© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
HARD CASTERS FOR SOFT FLOORS
CC4 – Conference Stacker Chair: Knoll MultiGeneration
PENDINGAPPROVAL
131© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
TABLET ARMBOOK BASEKTGLIDES
CC4 – Conference Stacker Chair: Knoll MultiGeneration
PENDINGAPPROVAL
132© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
TUBE BASEFIBER SEAT
CC4 – Conference Stacker Chair: Knoll Muuto Fiber Side Chair
PENDINGAPPROVAL
133© 2020 Knoll Inc.
ST3 – Café Stool:
› Chair, counter, and bar height options› Arm and armless versions› 4 leg baseOptions: › Textile finish options ranging from fabric to vinyl to include COM/Healthcare grade fabric and
wood. Al finishes to be able to clean using germicide or bleach solution
134© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
BAR-HEIGHT STOOLUPHOLSTERED SEAT PAD
ST3 – Café Stool: Knoll MultiGeneration
PENDINGAPPROVAL
135© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
COUNTER-HEIGHT STOOL
ST3 – Café Stool: Knoll MultiGeneration
PENDINGAPPROVAL
136© 2020 Knoll Inc.
CS2 – Computer Support Tools – Monitor Arms:
› Adaptable to single or double› Gas assists lifting, one finger adjustment and 360 degree movement› Quick release monitor holder› Mounting option to include C-clamp, bolt-through, grommet and wall mount› Wire management down arm› Dual monitor arms move independent from each other› Dual monitor arms position two screens side by side with minimum gap› A minimum of 10 year warrantyOptions: › Double pivot or Dual Joint Monitor arm allows for turning monitor 180 degrees › Sit-to-stand monitor arm option› Dual tandem monitor arm option› Triple monitor arm with independent movement or tandem option
137© 2020 Knoll Inc.
DETAILS:
• EACH ARM HOLDS UP TO 20LBS, ACCOMMODATING UP TO 95% OF THE MONITORS ON THE MARKET.
• SHIPS STANDARD WITH FAST RELEASE MOVEMENT JOINT. • EACH ARM OFFERS 165 DEGREES OF MONITOR TILT UP AND DOWN, 180 DEGREE OF SWIVEL
LEFT AND RIGHT AND 360 DEGREES OF ROTATION FOR PORTRAIT OR LANDSCAPE VIEWING. • EACH ARM OFFERS APPROXIMATELY 17” OF DEPTH ADJUSTMENT • EACH ARM FOLDS INTO ITSELF TO BE ON 2 7/8” DEEP WHEN FULLY COMPRESSED.• DURABLE AND LIGHTWEIGHT• ICORPORATES EASY-TO-USE EXTERNAL CABLE MANAGEMENT. • A VARIETY OF MOUNTING OPTIONS AND MAST HEIGHTS AVAILABLE.
CS2 – Computer Support Tools – Monitor Arms: Knoll ExtraSapper Double Monitor Arm
138© 2020 Knoll Inc.
DETAILS:
• EACH ARM HOLDS UP TO 20LBS, ACCOMMODATING UP TO 95% OF THE MONITORS ON THE MARKET.
• SHIPS STANDARD WITH FAST RELEASE MOVEMENT JOINT. • EACH ARM OFFERS 165 DEGREES OF MONITOR TILT UP AND DOWN, 180 DEGREE OF SWIVEL
LEFT AND RIGHT AND 360 DEGREES OF ROTATION FOR PORTRAIT OR LANDSCAPE VIEWING. • EACH ARM OFFERS APPROXIMATELY 17” OF DEPTH ADJUSTMENT • EACH ARM FOLDS INTO ITSELF TO BE ON 2 7/8” DEEP WHEN FULLY COMPRESSED.• DURABLE AND LIGHTWEIGHT• ICORPORATES EASY-TO-USE EXTERNAL CABLE MANAGEMENT. • A VARIETY OF MOUNTING OPTIONS AND MAST HEIGHTS AVAILABLE.
CS2 – Computer Support Tools – Monitor Arms: Knoll ExtraSapper Triple Monitor Arm
139© 2020 Knoll Inc.
CS3 – Computer Support Tools – CPU Holder:
› Powder coated steel or aluminum › Adjustable to support CPUs from 3.5" to 9.5" wide› Adjustable to support CPUs from 12" to 20" tall › Must support 40 pounds or greater› Slide out trackOptions: › Rotating track › Freestanding option with casters
140© 2020 Knoll Inc.
CS3 – Computer Support Tools – CPU Holder: Knoll ExtraSling CPU Holder
DETAILS:
• MOUNTS ON VIRTUALLY ANY WORKSURFACE• SUPPORTS MAXIMUM WEIGHT OF 75 POUNDS• SLIDES ON A 17” STEEL TRACK AND SWIVELS 360 DEGREES FOR EASY ACCESS TO WIRING. • ADJUSTS TO HOLD CPUs WITH TOTAL PERIMETER OF UP TO 64”. MINIMUM 2.5”W X 8”H.
141© 2020 Knoll Inc.
CS3 – Computer Support Tools – CPU Holder: Knoll ExtraAdjustable Vertical CPU Holder
DETAILS:
• MOUNTS ON VIRTUALLY ANY WORKSURFACE• SUPPORTS MAXIMUM WEIGHT OF 85 POUNDS• SLIDES ON A 17” STEEL TRACK AND SWIVELS 360 DEGREES FOR EASY ACCESS TO WIRING. • ADJUSTS TO HOLD EQUIPMENT 3.5” TO 9.3” WIDE BY 13.5” TO 22.5” HIGH.
142© 2020 Knoll Inc.
DA1 – Desk Accessories – Slat Wall, Rail and Freestanding Tools:
› Widths in 24”-60”, 12”-18” High› Must be able to mount on system furniture panels, wall mount and be available freestanding› Minimum support weight shall be 60 lbs› Variety of work/organizing tools meeting 5 of the folling 13 items; binder holder, letter tray,
pen/pencil cup, double square dish, hanging brackets, paper manager, utility hook, slat shelf dividers, universal shelf, telephone caddy, marker board, glove box/tissue box holder, and tack strip
› Made with heavy duty plastic in a variety of colors to match system’s furniture.› 10 year warranty
143© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
6-1/2” SLAT BOARDSLANTED SORTERSIDE SINGLE LETTER TRAYUTILITY TRAYPENCIL CUPTAPE DISPENSERFILE SORTER
DA1 – Desk Accessories – Slat Wall, Rail and Freestanding Tools: Knoll Extra – Orchestra Universal System Accessories
DETAILS:
• SLAT BOARD CAN BE INTEGRATED INTO PANELS, PRIVATE OFFICE WORKWALLS OR POWER AND DATA SERVICE WALLS.
144© 2020 Knoll Inc.
THIS STANDARD INCLUDES:
LOAD BAR/INFO RAILWORKSURFACE MOUNTING BRACKETSLANTED SORTERSIDE SINGLE LETTER TRAYPENCIL CUPTAPE DISPENSER
DA1 – Desk Accessories – Slat Wall, Rail and Freestanding Tools: Knoll Extra – Orchestra Universal System Accessories
DETAILS:
• THE UNIVERSAL LOAD BAR CAN BE MOUNTED ONTO A PANEL, STANCHON, WALL OR FREESTANDING DESK.
145© 2020 Knoll Inc.
Thank You
© 2020 Knoll Inc.
146© 2020 Knoll Inc.© 2020 Knoll Inc.
Top Related