8/11/2019 Joining manual
http://slidepdf.com/reader/full/joining-manual 1/6
Manual No. 32110Edition/da te : 9709.2/MGReplace s: 9709.1Autho rs : G ul/K/Ac
J oining sys tem
Flexproof
Joining manual
Spindle tape W-8
Please observe the following points when realizing
the joint:
Heed the type and width of the guide rail!
Tape width = guide rail width: Do not force the tape ends into theguide rail!
Install tape in such a way that the black side lies on the pulley orthe cylinder and the green one on the whirl.
After joining always check opt ical quality of the joint!
In ca se of q uestions and for supplementary literature a sk nearest Haba sit representation.
8/11/2019 Joining manual
http://slidepdf.com/reader/full/joining-manual 2/6
Manual No. 32110Edition/da te : 9709.2/MGReplace s: 9709.1Autho rs : G ul/K/Ac
J oining s ystem
Flexproof P a ge 2/6
W-8
1Preparing
78 01
6 m m30 mm /1.18 in.
Ca refully rea d through the
opera ting instructions a nd
manuals.
Standard dimension of fingers
for W-8: 6/30 mm (0.24/1.18 in.)
02 03 04
Die-cutting device AF-30 Hea ting press PQ-54, P Q-57 Cooling tongs CD-54, CD-60
Used devices
0 . 2
4
i n .1 2
3a 3b 3c
8/11/2019 Joining manual
http://slidepdf.com/reader/full/joining-manual 4/6
J oining s ystem
Flexproof P a ge 4/6
4Hot-pressing
03
P lug in ca ble a nd hea t up
hea ting p ress until the ta rget
temperature has b een reached(at least 5 min).
Clamp hea ting press on guide
rail with inse rted ta pe.
Make sure that
guide rail lies
perfectly centeredin the press.
Tape width 6-13 mm / 1 / 4 - 1 / 2 in . (narrow guide rail)
Set pressing time to 120 sec.
and w a it till time has expired.
After expiry o f the pres sing time in
the heating press, remove heating
press from the g uide rail.
Set cooling time to 120 sec. and
wait till time has expired.
Immediately clampcooling tongs onguide rail!
W-8
12 13
14
HR MIN SEC
START
STOP RESET
Set
Timer
HR MIN SEC
START
STOP RESET
Set
Timer
15
HR MIN SEC
START
STOP RESET
Set
Timer
HR MIN SEC
START
STOP RESET
Set
Timer
Manual No. 32110Edition/da te : 9709.2/MGReplace s: 9709.1Autho rs : G ul/K/Ac
Tape width 15-35 mm /5 / 8 - 1 3 / 8 in . (wide guide rail)
Set pressing time to 180 sec.a nd w a it till time ha s expired.
After expiry o f the pres sing time inthe heating press, remove heating
press from the guide rail.
Immediately clampcooling tongs onguide rail!
Set cooling time to 180 sec. andwait till time has expired.
11
15
14
12 13
8/11/2019 Joining manual
http://slidepdf.com/reader/full/joining-manual 5/6
J oining s ystem
Flexproof P a ge 5/6
4Hot-pressing (continued)
17
After cooling is completed
remove ta pe from guide rail
by steadily pulling.
Let the tape cool off to room
tempera ture outs ide of hea ting
press.
5Quality check of the joint
J oint is o k.After the tape has cooled
do wn, chec k the joint q uality.
Ca refully cut o ff tape ma terial
that has o ozed o ut with
scissors.
1. Penetration too strong
→ reduce p ressing time.
Careful!Do not damage tapeand tape edges!
Holes a nd ga ps
→ ma ke sure that finger tips
indent closely.
Finger tips sticking off
→ die-cut more precisely.
18 19 23
W-8
16
Manual No. 32110Edition/da te : 9709.2/MGReplace s: 9709.1Autho rs : G ul/K/Ac
2. Penetration too little→ increas e press ing time.
222120
16 17
201918
21 22 23
1
2
Top Related