Introduction to Ceramics
3-D Art 1 with Mrs. Graves
Clay Methods: Pinch
Clay Methods: Coil
Artist Research
Clay Methods: Slab
Upcoming Projects…
Clay Methods: Modeling
I. Vocabulary• Ceramics = A nonmetallic,
inorganic material that is exposed to extreme heat. The most common ceramic material is clay, but glass, plaster, and cement are ceramic materials, too.
I. Vocabulary
Ceramics
#1
I. Vocabulary• Pottery = Ware, such as
vases, pots, bowls, or plates, shaped from moist clay and hardened by heat.
I. Vocabulary
Pottery
#2
I. VocabularyClay
#3
I. Vocabulary• Clay
oWhat is it? Clay is the most universal material on earth. About 75% of the earth’s surface is clay or will eventually become clay…
I. Vocabulary…Clay is used to make more than just pottery. It can be found in many common items such as bricks, roof tiles, curling irons, spark plugs, and even...
…toothpaste!
#4
I. VocabularyoWhere does it come from? Clay comes from a rock called feldspar.
#5
I. Vocabulary…It takes centuries of geological weathering (being rained on, smashed by glaciers, having plants decay on it, etc.) to turn this rock into dust.
#6 Geological
weathering
I. Vocabulary After lying around
in the bottom of swamps and lakes, the dust picks up water and forms clay.
I. Vocabularyo The chemistry of clay:
Al2O3 ● 2SiO2 ● 2H2O
I. Vocabulary Al2O3 = Alumina
#7
I. Vocabulary SiO2 = Silica
#8
I. Vocabulary H2O = Water
#9
II. Properties of Clay• Plastic = Plastic is defined
as a material that can be molded. Clay is able to hold its form but is also able to be molded by hand. Water is necessary to make clay plastic.
#10Plastic
II. Properties of Clay• Porous = Porous means clay
is full of small holes so that water can escape as the clay dries. This keeps the clay from cracking as is dries.
#11 Porous
II. Properties of Clay• Able to Vitrify = Vitrification
is the conversion of clay into a hard glasslike substance when it is fired at a high temperature.
#12 Vitrify
III. Working with Clay• Forming Greenware
o Hand building methods = pinch, coil, slab, and modeling. Clay can also be thrown on a pottery wheel.
III. Working with Clay• Preparing clay
o Wedging= a large piece of clay is first cut into pieces with a cutting wire, then the pieces are rearranged and slammed together to make it easier for kneading.
#13 Wedging
III. Working with Clayo Kneading = similar to
kneading bread. The clay is rolled over on itself and pressed down several times. After kneading, cut the clay with a wire to check that there are no air pockets or lumps.
#14Kneading
Pinch method
#15
#16Coil method
#17Slab method
#18Modeling
III. Working with Clayo Score and slip = used to join
two pieces of clay together. A fork or needle tool can be used to score (or rough up) the surface and then slip (watered down clay) is applied at the joint like glue.
#19Score
#20Slip
III. Working with Clayo Leather hard = when the
clay has dried enough to be tough (like leather) but still workable. Used when building large forms.
#21Leather hard
III. Working with Clayo Bone dry = when all of the
water has evaporated from the clay and it can be fired. It can take several days for a piece to become bone dry.
#22Bone dry
III. Working with Clay• Kiln = the equipment that
heats up clay like a super-hot oven
#23Inside a kiln
III. Working with Clay• Firing and Glazing
oBisque firing = the first firing. Our clay is bisque fired at Cone 04, which means the kiln shuts off when it reaches 1915 F. After being bisque fired the ceramic piece is called bisqueware.
III. Working with Clayo Glazing = Glaze is applied
only to bisqueware. There are many different types of glaze. They can be applied by dipping, spraying, or brushing on.
#24Glaze
III. Working with Clayo Glaze Firing = this is the
second firing. Our glazes are all Cone 06, which means the kiln heats them to 1798 F. Once the piece has cooled it is finished!
Top Related