Clearview take no responsibility for the result of incorrect use of these installation instructions.Due to Clearview Continuous Improvement Program, Information may change without notice.
PAGE: 1
INSTALLATION GUIDE
M8 x 35mm Broaching Stud Z/P
10mm Flat Washer Z/P
01-ESTC01-0201-140305-01
01-140220-0101-140296-0101-140162-0101-140251-0101-140316-0102-ES7341-47 3.0mm Galvanised Fixed Strap
M8 x 25mm x 1.6mm washer Z/PM8 Nylon Insert Nut Hex Silver Z/PM10 x 16mm Socket Screw Z/P
Easy Slide Timber Chock6x90mm Hex L-Key Short Metric
INSTALLATION GUIDE
Clearview take no responsibility for the result of incorrect use of these installation instructions.Due to Clearview Continuous Improvement Program, Information may change without notice.
PAGE: 2
An Easy Slide should never be fitted to an existing inbuilt fridge slide, Warranty on the both Drawer IMPORTANT:
System and Easy Slide will be made Void if attempted. Easy Slides should only be fitted to a solid, fixed,
timber tops.
Step 1: Preparing the vehicle
Remove any cargo barrier dividers or shelving over the drawer system;
E nsure there will be no tie down lugs under the proposed positioning of the easy slide; and
E nsure the top of the drawer is free from debris.
IMPORTANT: Leave the protective plastic sleeves on the gas struts to either
side of the cradle for additional protection during assembly
Step 3: Complete Assembly of the Easy Slide
The Easy Slide MUST be bolted to a drawer top or at least partially IMPORTANT:
secured to a workbench via clamps at the rear to enable safe lowering of the
cradle (this installation guide will detail on a drawer top). DO NOT attempt to lower
the cradle prior to securing the slide. The side assist struts are under pre-load pressure
and considerable downward force on the handle will be required.
Step 2: Remove the Easy Slide from the Packaging
Place the Easy Slide on the vehicle drawer system, positioned roughly in place (refer figure 1)
R emove the drawer from underneath the slide
R elease the Easy Slide Transit Lock by pushing the centred yellow lever towards the right (refer figure 2)
Free the cradle for movement by pushing downwards on the yellow lever positioned to the right (refer figure 3), then
slide the cradle forwards to reveal the rear fixing holes (refer figure 4)
U sing timber screws, temporarily affix the rear of the Easy Slide to the drawer top (refer figure 5)
This installation guide is for fitting a Clearview Easy Slide to a vehicle drawer system
Some assembly of the slide is required prior to installation as it has been partially dismantled for packaging / freight
INSTALLATION GUIDE
Clearview take no responsibility for the result of incorrect use of these installation instructions.Due to Clearview Continuous Improvement Program, Information may change without notice.
PAGE: 3
Once the Easy Slide is secured, slide the cradle out to full extension, ensuring the slide lock has been engaged. An
audible 'click' can be heard when the slide lock has engaged (refer figure 7)
P lace the ply chock on the back edge of the fridge cradle (refer figure 8). This will be required to hold the cradle in
a lowered position.
Carefully manoeuvre the main arm so that the notch at the base of the arm lines up under the strut fixing. The strut
fixing will act as a temporary pivot to lower the cradle.
7 8
IMPORTANT: The pivot end narrowly misses the gas struts on either side of the cradle. Although each strut is
currently protected by temporary plastic sleeves, care should still be taken to ensure the struts are
not scratched at this point.
By pushing down on the handle, slowly lower the cradle until the top of the ply chock slips under the back edge of the
cradle frame
T he handle can now be released as the chock will stop the cradle from lifting.
Connect the handle to the Easy Slide by lining up the fixing holes at the bottom of the main arms with the thread in the
pivot point and inserting two (2) M10x16mm bolts with the Allen Key supplied.
INSTALLATION GUIDE
Clearview take no responsibility for the result of incorrect use of these installation instructions.Due to Clearview Continuous Improvement Program, Information may change without notice.
PAGE: 4
Enable the triggered cog lock mechanism by cutting the cable tie on the trigger to the left of the handle
S queeze the trigger and push down on the handle to release the ply chock. Release the trigger to engage the cog
lock
Return the Easy Slide to its home position and place your fridge into the cradle. See the Clearview Easy Slide User Guide
for more details
Test the positioning of the Easy Slide to ensure it remains clear of vehicle side trims and rear doors in all possible
configurations, including closing the vehicle rear door with the Easy Slide in its secured, home position
Step 4: Test and finalise the positioning of the Easy Slide
INSTALLATION GUIDE
Clearview take no responsibility for the result of incorrect use of these installation instructions.Due to Clearview Continuous Improvement Program, Information may change without notice.
PAGE: 5
IMPORTANT: Take CARE when testing whether the vehicle rear door can be closed without coming into contact with the
Easy Slide handle or fridge
If the Easy Slide needs repositioning, simply remove the temporary fixings and manoeuvre the Easy Slide to the
desired position
Ensure the Easy Slide does not extend further than the drawer contour panels (refer figure 9)
Step 5: Install the Easy Slide
Once the Easy Slide position has been tested and finalised, slide the carriage forward to reveal the rear fixing plate.
D rill into the timber top with an 8.5mm bit through the frame fixing holes
NOTE: Either left or right holes may be used to ensure the centre bearing panel of the drawer system is avoided.
Hold the coach bolt and strap assembly in the drilled holes at the rear of the drawer system from the underside of the
timber top and use the M8x25mm washer and nyloc nut to affix in place. Tighten the nyloc nuts with a socket spanner.
W ith the rear of the Easy Slide now secured, slide the cradle forward to full extension and repeat the process to affix
the front of the Easy Slide.
V acuum all swarf and the Easy Slide is now ready to use.
Please refer to the Clearview Easy Slide User Guide for safe operation.
9
Either left set or rightset of holes dependingon placement of slide.
Top Related