Front-end Product Training Program –Speed Dome
Table of Contents
Speed dome classification Speed dome basic informationFAQUpgrade
Speed dome Classification
Speed Dome Components
• Camera• High speed PTZ• Decoder• Dome enclosure • Fan• Heater
Speed Dome Components
Address, protocol dial
switch button
Main chip
Main control board
Speed Dome Components
Alarm Port
Power socket
User port
Switch board
Power board
Speed Dome Components
Encode chip Network
part
Connect to the switch board
Flash chip
Davinci
Speed Dome Layout
• After the rectify, the AC24V from the on-off voltage of U1( UCC3809 ) becomes the DC+12V , among which , the U2 ( TLP281-1 )、 U3 ( TLV431 ) is the key chip of the voltage auto control.
• +12V from U4 ( L7805 ) to VCC ( +5V ), VCC from U5 ( 76381-3.3V ) to +3.3V.
• U8 ( LM3S608 ) alarm control chip. Please burn the boot application and then upgrade the application via the COM. The speed dome RS485 connects to the RS232 of the PC is via the AMP socket and the U3 (184 chip) of the main board.
FAQ
•The alarm output control is from the 19/20-pin of the U8(LM3S608) to control the dynatron Q5/Q4, and then send to the JK1,JK3 of the U10 ( ULN2003 ) reverse relay. In normal status, the relay 4/13 and 6/11 is close. Then 4/13 and 8/9 are open. The short circuit cap of jump J13/J14 is in the 2/3/-pin.
FAQ
FAQ
+12V becomes +7V via U5 ( MP1411 ), and then becomes VCC via ( L7805 ) VCC ,then becomes +3.3V via U14 ( AMC1117-3.3V ), then +3.3V becomes +3.3VA via L5 , +12V becomes +12VA and +12VA1 via L7 and L4 to go to the stepper. The reset is done by the U2( ASM705 ) chip.
FAQ
The horizontal position uses the new component : Hall components -A1104-(SIP-3) , it uses the electromagnetic induction to test the horizontal test. The tilt stop is to slightly touch the on-off button (External, from J4 ).
Stepper control : U11 ( LPC2365 ) needs to burn the application. The control application will be sent to the chip U9, U12 ( L6219DSA ) to drive the stepper via the U10 ( TLC7225C ) 4-channel D/A switch.
FAQ
U7 ( MAX7456 ) is OSD chip , VCC is to provide the power , clock X3 ( 27MH ), the 8 to 11–pin is to communicate with the ARM , 22-pin is for the video input, 26-pin is for the video output,U13 ( OPA690) is for video output.The application can embed the OSD to video signal.You can check the U7 working status if the OSD is abnormal.
• There is no respond after turn on the device. Please make sure there is no short circuit. Test +12V, VCC ( +5V ) , +3.3V is OK or note. If there is a problem please fix the power board. Finally check the AMP co
nnection is OK or not.
FAQ
FAQ
On-off button
FAQ
The 485 signal is from the user port J9 ( power board ) to the main board for the U3 ( LBC184 ), and then to the U11( LPC2365 ) . LED1 is the RS485 indicator light.
The problem may be :1 Can not upgrade the application.2 Can not control the PTZ or can not go to the menu.
The reason may be :1 Address, protocol setup problem2 U3 ( LBC184 ) working improperly or is malfunction3 AMP connection problem
FAQ
184 is communication port
FAQ
1 、 Main board is no power: AMP or the electronic brush is abnormal. 2 、 Can not control the PTZ: U3 ( LBC184 ) chip is abnormal.Address, protocol or baud rate setup is error.3 、 No character or abnormal: application is wrong, or U7 ( MAX7456 ) working is improper or malfunctio
n.
FAQ
Davinci main board :The video signal will be sent to the main chip ( U7 TMS320) tocompress via the video A/D(U21 5150 ) chip. Then from the networkcard chip ( U5 RTL8201 ) to our PC.Network problem. Please make sure the Davinci board has booted up.Please check the voltage and the clock if it does not boot up properly. Ifit has booted up properly ,please change the application. If there is a network problem when the board properly booted up,please check the IP address is OK or not. Please check theRTL8201(U5) if the IP is OK. Otherwise change the IP address (Pleaserefer to the following information.)
FAQHow to change the IP when the network is error.You can change via the COM.Press the * when the device boots up.
U-Boot 1.1.4 for DAHUA Davinci ;Version 3.0; modify by Sword;20071212 (Jan 13 2009 - 15:10:14)
U-Boot code: 81080000 -> 81099694 BSS: -> 810B2E68RAM Configuration:Bank #0: 80000000 64 MBFlash Manufacturer=AMD flash reset;add by SwordFlash: 16 MBIn: serialOut: serialErr: serialARM Clock :- 256MHzDDR Clock :- 162MHzCPU:DM6446nARM Clock :- 297MHzLoading ............DHBOOT# *****
Unknown command '*****' - try 'help'DHBOOT#
FAQ
“DHBOOT#” input command here. “setenv dh_keyboard 0 setenv appauto 0 save”
Reboot and then input “netinit IP address subnet mask defaultgateway ” after you see #, input ii and click the return button. Pleasereboot and then input the following information.
“setenv dh_keyboard 1 setenv appauto 1 save”
Upgrade Tool
Power board application download cable
USB Connection Cable Download Tool
Upgrade Tool
Main board download cable
Download Tool (LPT) Download Tool Switch Cable
Upgrade ToolLM3S608 alarm output chip in the power board is to burn the applications. Please use the tool power board application download cable to burn the Boot application. And then use the 232 to 485 tool to burn the main applications. There is no alarm if there is no main applications.
LPC2365 on the main control board is the key control chip. The Boot application can use the tool or the on-line download tool to burn. The on-line burn is to use the main board download cable to burn the Boot application and then uses the 232 to 485 switcher to burn the main applications via the RS485. You can not control the PTZ if there is no application in the LPC2365.
For the Davinci board, you can use the burner to burn the Boot application to the Flash and then jointing to the board to upgrade via the TFTP. You can not see the network video if there is no application.
Upgrade Tool
LPC2365 on-line burn port
LM3S608 on-line burn port
Thank you !
Top Related