Copyright and Terms of Service
Copyright © Texas Education Agency, 2011. These materials are copyrighted © and trademarked ™ as the property of the Texas Education Agency (TEA) and may not be reproduced without the express written permission of TEA, except under the following conditions:
1) Texas public school districts, charter schools, and Education Service Centers may reproduce and use copies of the Materials and Related Materials for the districts’ and schools’ educational use without obtaining permission from TEA.
2) Residents of the state of Texas may reproduce and use copies of the Materials and Related Materials for individual personal use only, without obtaining written permission of TEA.
3) Any portion reproduced must be reproduced in its entirety and remain unedited, unaltered and unchanged in any way.
4) No monetary charge can be made for the reproduced materials or any document containing them; however, a reasonable charge to cover only the cost of reproduction and distribution may be charged.
Private entities or persons located in Texas that are not Texas public school districts, Texas Education Service Centers, or Texas charter schools or any entity, whether public or private, educational or non-educational, located outside the state of Texas MUST obtain written approval from TEA and will be required to enter into a license agreement that may involve the payment of a licensing fee or a royalty.
Contact TEA Copyrights with any questions you may have. 2
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
FIRE SERVICE LADDERSPart I
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER COMPONENTS
Beam Butt, heel, or base Butt spurs Heat sensor label Hooks Rails Rungs Truss block
4
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER COMPONENTS(CONTINUED)
Bed/base/main section Dogs, locks, pawls Fly section Footpads/shoes Halyard Protection plates Pulley Tip/top
5
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER COMPONENTS (CONTINUED)
Stops on the Bed and Fly Sectionsof an Extension Ladder
Tie Rods on a Wooden Ladder
6
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER TYPESSINGLE LADDERS Consist of one fixed length section Identified by their overall length
6 to 32 feet Most common lengths range from 12 to 24 feet
Also called wall ladders and straight (wall) ladders Used for quick access to windows and roofs on one-
and two-story buildings
7
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER TYPESSINGLE LADDERS (CONTINUED) Roof ladders
Have folding hooks that can anchor over the ridge of pitched roofs
Lie flat on the roof’s surface Distributes the weight of the firefighter and helps prevent
slipping Can be used as single wall ladders Range from 12 to 24 feet in length
Folding ladders (Attic ladders) Single ladders that are most often used to access
attics Have hinged rungs that allow the beams to rest
against each other while the ladder is closed Folding ladders range from 8 to 16 feet in length The most common length is 10 feet
8
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER TYPESEXTENSION LADDERS Have a bed or base section and one or more fly
sections that extend the ladder’s length Are adjustable to the length needed to access roofs
and windows Range in length from 12 to 39 feet Pole ladders (Bangor ladders)
Have poles attached to swivels at the top of the bed section that add leverage and stability when they are being raised
Must be equipped with staypoles if 40 feet or longer (NFPA 1931)
Constructed with two to four sections Most are 50 feet or less
9
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER TYPESEXTENSION LADDERS (CONTINUED) Combination ladders
Are designed to be a self-supporting step ladder (A-frame), a single ladder, or an extension ladder
Range from 8 to 14 feet in length The most popular length is 10 feet Must be equipped with positive locking devices to secure the ladder
when in the open position
Pompier ladders (scaling ladders) Single beam ladders with rungs extending through the beam, and
projecting from both sides Have a large metal “gooseneck” that is used to hook onto window
sills or other openings Used to climb from floor to floor, through the use of exterior
windows or openings Range from 10 to 16 feet in length 10
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
Ladder Types
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
11
LADDER CONSTRUCTION
MetalGood conductor of heat,
cold, and electricityEasy to repairMay fail suddenly when
exposed to heat or flameWidest range of sizes
12
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER CONSTRUCTION (CONTINUED)
WoodMost expensive and
heaviestRetain strength when
exposed to heat or flame
Very durable
13
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER CONSTRUCTION (CONTINUED)
FiberglassPoor conductors of electricityMay suddenly crack or fail when
overloadedMay burn when exposed to flame
14
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER INSPECTION AND MAINTENANCE
NFPA 1931 Certification label applied by the
manufacturer Maintenance – “keeping in a state of
usefulness or readiness” Repair – “restore or replace what is damaged
or worn out” Ladders must be serviced and tested
Before being put in service Annually After exposure to high heat After exposure to rough treatment
15
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER INSPECTION AND MAINTENANCE (CONTINUED)
General maintenance requirements Keep ladders free from
moisture Do not expose ladders to
vehicle exhaust or engine heat
Do not store ladders where they will be exposed to the elements
Do not paint ladders, except for the top and bottom 18 inches of the beams for the purpose of identification or visibility
16
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
CLEANING LADDERS Dirt and debris on ladders can cause them to
malfunction Use a soft bristle brush and running water Tar, oil, and greasy residue should be removed with
mild soap and water, or solvents that are safe for the environment
Always wipe wet ladders dry Inspect while cleaning and follow Standard Operating
Procedures (SOPs) Apply lubricants properly
17
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
INSPECTION AND SERVICE TESTING LADDERS
NFPA 1932 requires ladders to be inspected monthly, and after each use By approved testing organizations or fire service
personnel
18
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
INSPECTION AND SERVICE TESTING LADDERS (CONTINUED)
Inspections should include: Verification of heat sensing labels (look for a
change in color, indicating heat exposure) Rungs for damage and wear Rungs for tightness Bolts and rivets for tightness Welds for cracks and/or defects Beams and rungs for cracks, splintering, breaks,
gouges, checks, wavy conditions, or deformation
19
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
INSPECTION AND SERVICE TESTING LADDERS (CONTINUED)
For wooden ladders and ladders with wooden components, look for Ladder finishes that are chafed or scraped Darkened varnish (indicates exposure to heat) Dark streaks in the wood (indicates deterioration
of wood) Marred, worn, cracked, or splintered parts Rounded or smooth shoes Water damage
20
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
INSPECTION AND SERVICE TESTING LADDERS (CONTINUED)
Roof ladders Make sure the roof hook
assemblies operate smoothly
Look for signs of rustDeformed hooksParts firmly attached
with no signs of being loose
21
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
INSPECTION AND SERVICE TESTING LADDERS (CONTINUED) Extension ladders
Check the following: Pawl assemblies (hooks and fingers
should move in and out freely) Halyard should be replaced if damaged Halyard cables should be taut when the
ladder is bedded Make sure the pulleys spin freely Make sure the ladder guides are in place,
and that the ladder can move freely Staypole toggles and the mechanism used for detachable
staypoles should be checked to make sure that they move and operate freely
Remove ladders that need to be repaired and tested Destroy ladders that cannot be repaired, or scrap
them for parts 22
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
NFPA REQUIREMENTS NFPA 1901, Standard for Automotive Fire Apparatus,
specifies the minimum length and types of ladders to be carried on pumpers/engine companies: 1 roof ladder 1 extension ladder (recommended to be 35-foot in areas
where no ladder trucks are in service) 1 attic ladder
NFPA 1901, Standard for Automotive Fire Apparatus, specifies that aerial ladders must carry the following: One 10-foot or longer attic ladder Two roof ladders that are at least 16 feet long One combination ladder at least 14 feet long One 24-foot or longer extension ladder One 35-foot extension ladder
23
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
FIRE SERVICE LADDERSPart II
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER SAFETY Choose the proper ladder for the job Wear appropriate Personal Protective Equipment (PPE) Use your leg muscles when lifting ladders below the
waist Do not raise ladders within 10 feet of electrical lines Place the ladder at the proper climbing angle (75
degrees) Do not overload the ladder (one firefighter every 10
feet, or one per section) Tie in with a leg lock or a ladder belt when working Use ladders for their intended purposes Inspect ladders for damage or wear after each use
25
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER SELECTION Residential stories are about 10 feet with 3
feet between the floor and the window Commercial stories are about 12 feet with 4
feet between the floor and the windowsill The base of the ladder should be able to be
placed 1/4 of the vertical distance from the ground to where the ladder comes in contact with the wall
The optimum climbing angle is about 75 degrees
Ladders should extend three to five rungs beyond the roof edge to provide safe footing and handholds to step off the ladder
The tip of the ladder should be placed even with the top of the window on the windward side (upwind), to gain access to narrow windows or to ventilate
The ladder tip should be placed just below the windowsill to facilitate rescues
26
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
PROPER LADDER LIFTING AND LOWERING METHODS Have the proper number of personnel for the job When raising a ladder bend your knees, keeping your
back as straight as possible, and lift with your legs When 2 or more firefighters are lifting, the firefighter
at the butt end should give the ladder commands When lowering a ladder use your leg muscles
27
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER CARRIES
One Firefighter Low-Shoulder Carry Rest the ladder’s upper beam on your shoulder,
while your arm goes between two rungs (Single or Roof Ladder)
Carry the butt end of the ladder in front, slightly lowered
28
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER CARRIES (CONTINUED)
Two Firefighter Low-Shoulder Carry Most commonly used for 24-, 28-, and 35-foot
extension ladders Allows for excellent control of the ladder The forward firefighter (at the butt) places his or
her free hand over the upper butt spur to prevent injury if there is a collision while the ladder is being carried
29
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER CARRIES (CONTINUED)
Three Firefighter Flat-Shoulder Carry Usually used on extension ladders up to 35 feet
in length Two firefighters on one side of the ladder (one on
each end) A single firefighter on the opposite side of the
ladder in the middle
30
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER CARRIES (CONTINUED)
Four Firefighter Flat-Shoulder Carry The ladder is carried on the flat, as in the three
firefighter flat-shoulder carry, except for the positioning
There are two firefighters on each end of the ladder, opposite each other
31
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER CARRIES (CONTINUED)
Two Firefighter Arm’s Length On-Edge Carry Best performed with lightweight ladders The firefighters are positioned on the bed-section
of the ladder while the ladder is in a vertical position (on-edge)
32
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
LADDER CARRIES (CONTINUED)
Special Procedures for Carrying Roof Ladders A firefighter may have to carry
a roof ladder tip forward Intends on climbing another
ground ladder Allows him or her to place the
roof ladder, with the hooks deployed, on a sloped roof
Use the low-shoulder method with the hooks/tip forward
33
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
POSITIONING GROUND LADDERS
Responsibility for positioning Officers usually choose the general location Personnel carrying the ladder usually decide the
exact location The firefighter at the butt end makes the decision If there are two firefighters at the butt end, the
firefighter on the right side is responsible This procedure changes from department to
department
34
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
POSITIONING GROUND LADDERS(CONTINUED) Place ladders at a minimum of two points on different sides of the
building to allow for emergency egress if necessary Take advantage of the building’s construction when placing a ladder
(such as the corners) Raise the ladder directly in front of the window if you are going to use the
ladder to support a smoke ejector. Place the ladder tip on the wall directly above the window opening.
Try not to place ladders on uneven terrain Avoid placing ladders in avenues of egress; attempt to place ladders to
the side of the opening where firefighters need to gain entry, or where evacuation may occur
Avoid heat and flames whenever possible Don’t place ladders on top of trapdoors, grates, or manholes that are
located on sidewalks or streets The desired angle of inclination is approximately 75 degrees Proper distance between the heel of the ladder and the building can be
determined by dividing the length of the ladder used by 4 35
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
POSITIONING GROUND LADDERS(CONTINUED)
36
Don’t place a ladder where there are overhead obstructions.
Try not to place ladders over openings to avoid exposure to heat and flame.
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
SECURING THE LADDER
On extension ladders Make sure the ladder locks are locked Tie the halyard with a clove hitch and an
overhand safety knot Prevent movement of the ladder by tying the
ladder in, or by heeling the ladder
37
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
HEELING THE LADDER
Underneath the ladder method Stand beneath the ladder with feet
shoulder’s width apart, and one foot slightly in front of the other
Grasp the beams at about eye level and then pull backward, pulling the ladder against the building
Wear head and eye protection Do not look up as someone climbs
the ladder Grasp the beams and not the rungs Be aware of the potential for falling
objects 38
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
HEELING THE LADDER(CONTINUED)
Outside the ladder method Stand on the outside of the
ladder and chock or secure the ladder with one foot placed against the beam at the butt, or on the bottom rung
Grasp the beams with your hands and press the ladder against the building
Stay alert for firefighters coming down the ladder
39
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
HEELING THE LADDER(CONTINUED)
Tying in Tie the ladder securely to an
object whenever possible, to prevent it from slipping or pulling away from the building
Use a hose, rope, tool, or strap to secure it
This frees you from having to stay with the ladder to secure it
40
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
FIRE SERVICE LADDERSPart III
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
CLIMBING AND DESCENDING LADDERS Climb smoothly by keeping your
knees bent Keep your balanced (body
perpendicular to the ground) Keep your eyes focused forward
(look at the tip of the ladder occasionally)
Keep your arms straight (horizontal) during the climb to keep your body away from the ladder and allow for freedom of movement
Keep your hands on the rungs (palms down with thumbs under the rung)
Grasp alternate rungs while climbing
42
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
CLIMBING AND DESCENDING LADDERS(CONTINUED) Coordinate your hand and foot
movements with your opposing hand and foot on the ladder
Use your leg muscles to push yourself upward
Do not reach your arms and hands above your head
Develop form as you practice; speed comes with repetition
When carrying equipment Slide your free hand under a beam as
you climb, maintaining constant contact with the ladder
Hoist tools and equipment whenever possible
43
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
WORKING FROM A LADDER Firefighters must work with
both hands while working from a ladder
Use a ladder belt or leg lock to make sure both hands are free to work
If a ladder belt is used, it should be securely tightened around the waist and attached to a rung
A leg lock can be used to secure a firefighter to a ladder, with the leg opposite the side of the ladder your hands are working on
44
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
ASSISTING VICTIMS DOWN LADDERS
Ladder placement Rescue from a window
requires the ladder to be placed just below the sill
To bring victims down a ladder, at least four firefighters are needed Two inside the building One or two on the ladder One heeling the ladder
45
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
ASSISTING VICTIMS DOWN LADDERS
Conscious victims can be lowered feet first (facing the building) onto the ladder
An unconscious victim can be held on the ladder the same way as a conscious victim, with the victim’s weight resting on the rescuer’s knee
46
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
ASSISTING VICTIMS DOWN LADDERS(CONTINUED)
The victim’s feet are placed outside the rails The rescuer must grasp the rungs to provide a
secure hold on the ladder, and to help prevent the victim’s head from hitting the ladder
The unconscious victim can also be turned around, facing the rescuer to reduce the chance of the victim’s limbs catching on the rungs
The victim’s weight is supported at the crotch by one of the rescuer’s arms and at the chest by the other arm
47
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
ASSISTING VICTIMS DOWN LADDERS (CONTINUED) Extraordinarily heavy victims will require two rescuers
Two ground ladders are placed side-by-side One rescuer supports the victim’s waist and legs The second rescuer supports the victims head and upper
torso Small children may be brought down a ladder as they are
cradled across the rescuer’s arms
48
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
RESOURCES 1418001775, Introduction to Fire Protection (3rd
Edition), Klinoff, Robert
0135151112, Essentials of Firefighting (5thEdition), International Fire Service Training Association (IFSTA)
Images used with permission from IFSTA.
49
Copyright © Texas Education Agency 2011. All rights reserved.Images and other multimedia content used with permission.
Top Related