ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 1 of 117
ESTIMATING DATA 2016
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 2 of 117
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 3 of 117
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 4 of 117
D K TYAGI, IDSE
Chief Engineer Jt DGW(Utility)
Military Engineer Services, Sub Dte of Works (Utilities),
Engineer-in-Chief’s Branch, Integrated HQ MoD(Army),
Kashmir House, Rajaji Marg, New Delhi 110001
Tel & Fax :011 23019109
PREFACE
Estimating Data for E/M items was last revised in the year 2007.
Since then it is being used for all estimates in spite of all round increase
in rates of various items. The earlier ED was formulated based on RC
rates the items available on RC of DGS&D. However a policy decision has
been taken to do away with RC items and use the items of known makes
and brands so as to improve the image of organization and provide better
quality services.
The work of revision of ED was undertaken in the year 2015 when
rates of certain water supply items and PHE related items were revised in
the interim. The new revised ED 2016 has now been worked out based
on rates obtained from reputed brands minus the available rebates plus
the add on like excise duty, sales tax, transportation charges, service tax,
work contract tax and contractor profit etc. The arrived rates have been
compared for consistency with rates available from various State and
Central Government agencies.
Each HQ CE Command was entrusted the work of preparation of
ED for certain items and finally all item rates were compiled at E-in-C’ Br.
The sincere work done by all including Commands is hereby
acknowledged. This includes the team of PHE experts from ADG (D&C )
and from E-in-C’ Br. The valuable suggestions given by DGW also
resulted in enhanced usefulness of the document.
It is sanguinely presumed that this document will result in pragmatic
estimates of all E/M related schemes and necessary feedbacks received
from ground especially for LED lamps and Solar panels etc will improve
the value of the ED 2016. At E-in-C Branch the special mention is due for
Shri S K Arora and Shri Sunil Aggrawal Directors at Utility Sub Dte who
have worked whole heartedly to make it happen.
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 5 of 117
SECTION DESCRIPTION ITEM No
Section 1
External Electrification
1 to 761
GENERATING SET DIESEL ENGINE DRIVEN 1 to 30
TRANSFORMERS 31 to 48
HT SWITCH GEAR 49 to 56
SF6 CIRCUIT BREAKER 57 to 65
HT CTs & PTs 66 to 73
COMPACT SUB STN 74 to 81
LOAD BREAK SWITCH 82 to 83
GANG OPERATED AIR BREAK SWITHCHES 84 to 93
RUBBER MAT AND HAND GLOVES 95 to 98
LT SWITCH GEAR 99 to 104
COMPACT AIR INSULATED RISING MAINS 105 to 122
BUS TRUNKING 123 to 142
PLUGGING BOXES 143 to 148
CAPACITOR 149 to 213
LT SWITCH 214 to 228
RCCB & MCCB 229 to 280
ON LOAD CHANGE OVER SWITCH 281 to 316
VOLTAGE STABILIZER & UPS 317 to 353
ARMOURED XLPE CABLES & COPPER CONDUCTOR
354 to 402
CABLE JOINTING KIT & CABLE GLAND 403 to 453
AERIAL BUNCHED CABLE & OVER HEAD LINE ON POLE
454 to 542
4 POLE AND 2 POLE STRUCTURE 543 to 550
LIGHTING ARRESTORS & EARTHING 551 to 555
SERVICE CONNECTIONS & METERS 556 to 573
FANS 574 to 586
TIME SWITCHES & STREET LIGHT / FLOOD LIGHT
587 to 611
LED STREET LIGHTS, FLOOD LIGHTS & POST TOP LANTERNS
612 to 628
INDUSTRIAL LIGHT FITTING & BULK HEAD FITTINGS
629 to 632
INDOOR LIGHT FITTINGS & LED INDOOR LIGHTS
633 to 666
HIGH MAST LIGHTS 667 to 669
SHADOWLESS LIGHT FITTINGS 670 to 673
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 6 of 117
FLAME PROOF, WEATHER PROOF, DUST PROOF, DUST TIGHT & TOTALLY ENCLOSED LIGHT FITTINGS
674 to 696
PCC POLES, STEEL TUBULAR POLES & SWAN NECK TYPE POLES
697 to 710
CRANES 711 to 738
LIFTS 739 to 753
LIGHTING PROTECTION 754 to 757
EXCAVATION BY TRENCHLESS TECH 758 to 758
SOLAR PV GENERATION 759 to 761
Section 2
External Water Supply
1001 to 1472
TUBE WELLS 1001 to 1014
PUMPSET / STARTER 1015 to 1061
DISINFECTION,TREATMENT PLANTS 1062 to 1061
METALLIC PIPES 1072 to 1161
UPV & PP-R PIPES 1162 to 1209
VALVES & STRAINER 1210 to 1313
STOP COCK & BIB COCK 1314 to 1325
HOT WATER APPARATUS 1326 to 1337
FIRE FIGHTING 1338 to 1416
BEAM MASTER DETECTOR 1417 to 1418
ANNUCIATING DEVICES 1419 to 1429
PA SYSTEM 1430 to 1447
SWIMMING POOL FILTRATION PLANT 1448 to 1451
PRESSURE FILTER 1452 to 1460
SWIMMING POOL WATER TREATMENT 1461 to 1468
RO PLANT 1469 to 1472
Section 3
Refrigeration, Air Conditioning, Refrigerators & Central Heating System
1501 to 1584
REFRIGERATORS 1501 to 1504
WATER COOLER 1505 to 1508
DEEP FREEZER 1509 to 1512
EVAPORATIVE COOLER (DESERT COOLER) 1513 to 1517
WINDOW AIR CONDITIONER 1518 to 1520
SPLIT AIR CONDITIONER 1521 to 1523
AIR CONDITIONER CASSETTEE TYPE 1524 to 1526
PACKAGE TYPE AIR CONDITIONING 1527 to 1532
CENTRAL AIR CONDITIONING PLANTS 1533 to 1541
PRECISION AIR CONDITIONING 1542 to 1545
AIR CURTAIN 1546 to 1550
CHEMICAL DEHUMIDIFIERS 1551 to 1556
CENTRAL HEATING SYSTEM 1557 to 1570
BOILER(OIL FIRED) 1571 to 1584
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 7 of 117
Section 4
Tools & Plants
2201 to 2322
ALUMINUM LADDER 2201 to 2205
CRIMPING TOOLS 2206 to 2214
DIGITAL METER 2215 to 2220
OTHER METER 2221 to 2231
DRILL & BLOWER 2232 to 2233
COMMON HAND TOOLS 2234 to 2300
CENTRIFUGE MACHINE FOR TRANSFORMER OIL 22301 to 2304
DISCHARGE ROD 2305 to 2309
CABLE FAULT LOCATING MACHINE 2310 to 2311
WATER SUPPLY 2312 to 2321
SWIMMING POOL 2322
Section 5
Public Health Engineering with tech data
3001 to 3185
GRAVITY SEWERS 3001 to 3040
SEPTIC TANKS AND SHALLOW SEWER 3051 to 3065
SOAL WELLS 3068 to 3082
SUMP WELL CUM PUMP HOUSES 3101 to 3133
SUBMERSIBLE PUMPS 3134 to 3155
SEWAGE TREATMENT PLANT (MBBR Based) 3171 to 3185
Section 6
Technical Data for Section 1 to 4
Appendix ‘A’
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 8 of 117
SECTION - 1
(EXTERNAL ELECTRIFICATION)
( Item No 1 TO 761 )
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 9 of 117
Item No Description of Item Unit Rate
SECTION - 1 (EXTERNAL ELECTRIFICATION)
( Item No 1 TO 761 )
GENERATING SET DIESEL ENGINE DRIVEN
1
Supply and installation of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire, engine as per IS:10001/ 10002 and Alternator as per IS: 13364 complete with foundation (as per OEM design), control panel with necessary meter and sound proof canopy as per CPCB norms of capacity upto 10 KVA
KVA 42,599
2 -do- but above 10 KVA & upto 15 KVA KVA 30,364
3 -do- but above 15 KVA & upto 20 KVA KVA 26,132
4 -do- but above 20 KVA & upto 30 KVA KVA 20,223
5 -do- but above 30 KVA & upto 40 KVA KVA 17,946
6 -do- but above 40 KVA & upto 50 KVA KVA 15,973
7 -do- but above 50 KVA & upto 62.5 KVA KVA 13,202
8 -do- but above 62.5 KVA & upto 82.5 KVA KVA 11,874
9 -do- but above 82.5 KVA & upto 100 KVA KVA 11,617
10 -do- but above 100 KVA & upto 160 KVA KVA 10,285
11 -do- but above 160 KVA & upto 250 KVA KVA 10,232
12 -do- but above 250 KVA & upto 320 KVA KVA 10,115
13 -do- but above 320 KVA & upto 400 KVA KVA 9,573
14 -do- but above 400 KVA & upto 500 KVA KVA 9,716
15 -do- but above 500 KVA KVA 9,716
GENERATING SET DIESEL ENGINE DRIVEN WITH AMF PANEL
16
Supply and installation of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire, engine as per IS:10001/ 10002 and Alternator as per IS: 13364 complete with relay panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy as per CPCB norms and foundation etc. of capacity upto 10 KVA
KVA 49,435
17 -do- but above 10 KVA & upto 15 KVA KVA 36,451
18 -do- but above 15 KVA & upto 20 KVA KVA 30,896
19 -do- but above 20 KVA & upto 30 KVA KVA 23,737
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 10 of 117
Item No Description of Item Unit Rate
20 -do- but above 30 KVA & upto 40 KVA KVA 20,929
21 -do- but above 40 KVA & upto 50 KVA KVA 18,942
22 -do- but above 50 KVA & upto 62.5 KVA KVA 15,791
23 -do- but above 62.5 KVA & upto 82.5 KVA KVA 13,838
24 -do- but above 82.5 KVA & upto 100 KVA KVA 13,806
25 -do- but above 100 KVA & upto 160 KVA KVA 11,895
26 -do- but above 160 KVA & upto 250 KVA KVA 11,530
27 -do- but above 250 KVA & upto 320 KVA KVA 11,337
28 -do- but above 320 KVA & upto 400 KVA KVA 10,722
29 -do- but above 400 KVA & upto 500 KVA KVA 10,722
30 -do- but above 500 KVA KVA 10,722
Building for Generator is not required but operator rest room, toilet & store for fuel is to be planned and estimated separately.
TRANSFORMER 11 KV/433 V VOLTAGE RATIO
31
Supply and installation of copper wound transformer step up/ step down, indoor/outdoor type complete with standard fittings, HT 11 KV 3 Phase, LT 433 volts, 3 Phase 4 wire with off load tappings on HT side to vary secondary voltage within limit, all as per IS:2026 of capacity upto 63 KVA
KVA 4,708
32 -- do -- but of capacity above 63 KVA and upto 100 KVA
KVA 5,121
33 -- do -- but of capacity above 100 KVA and upto 160 KVA
KVA 3,629
34 -- do -- but of capacity above 160 KVA and upto 200 KVA
KVA 2,920
35 .--do-- above 200 KVA and up to 300 KVA KVA 2,814
36 -- do -- but of capacity above 300 KVA and upto 400 KVA
KVA 2,285
37 -- do -- but of capacity above 400 KVA and upto 500 KVA
KVA 2,042
38 -- do -- but of capacity above 500 KVA and upto 750 KVA.
KVA 2,042
39 -- do -- but of capacity above 750 KVA KVA 1,767
Note: Same rate, as above, are applicable for BEE 3 star rated 11 KV/433 V distribution transformer, Aluminium wound up to 200 KVA capacity.
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 11 of 117
Item No Description of Item Unit Rate
TRANSFORMER 33 KV/11K V WITH “OFF LOAD” TAP CHANGER
40
Supply and installation of copper wound transformer step up/ step down, outdoor type complete filled with oil, with standard fittings and foundation, HT 33 KV, secondary 11 KV, 3 phase, with OFF load tap changing , all as per IS: 2026 of capacity up to 1000 KVA
KVA 2,285
41 -- do -- but of capacity above 1000 KVA and upto 1600KVA
KVA 2,042
42 -- do -- but of capacity above 1600 KVA and upto 2000 KVA
KVA 1,735
43 -- do -- but of capacity above 2000 KVA and upto 2500 KVA
KVA 1,672
44 -- do -- but of capacity above 2500 KVA and upto 5000 KVA
KVA 1,672
TRANSFORMER 33 KV/11K V WITH “ON LOAD” TAP CHANGER
45
Supply and installation of copper wound transformer step up/ step down, outdoor type complete filled with oil, with standard fittings and foundation, HT 33 KV, secondary 11 KV, 3 phase, with ON load tap changing , all as per IS: 2026 of capacity up to 2500 KVA
KVA 2,031
46 -- do -- but of capacity above 2500 KVA and upto 5000 KVA
KVA 2,000
47 -- do -- but of capacity above 5000 KVA and upto 7500 KVA
KVA 1,937
48 -- do -- but of capacity above 7500 KVA KVA 1,789
Note: Item No 31-48 Cost of RCC Foundation for Transformer and Cattle fencing (1.5m high) around is included in above rates.
HT SWITCH GEAR
VACUUM CIRCUIT BREAKER
(INDOOR)
49
Supply and installation of HT 11 KV, 3 phase, 50 Hz totally enclosed metal clad switchgear complete with Vacuum circuit breaker having rupturing capacity 250 MVA, overload and earth fault protection, ammeter, voltmeter and of rating upto 400 Amp
Each 5,98,321
50 -- do -- but rupturing capacity 350 MVA of rating upto 630 Amp
Each 7,10,543
51 -- do -- but of 800 Amp capacity Each 7,61,464
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 12 of 117
Item No Description of Item Unit Rate
52 -- do -- but of 1200 Amp capacity Each 8,63,434
53 -- do -- but of 1600 Amp capacity Each 9,04,040
54 -- do -- but of 2500 Amp capacity Each 9,11,362
(OUTDOOR)
55
Supply and installation of HT 11 KV, 3 phase, 50 cycles totally enclosed metal clad switchgear complete with Vacuum circuit breaker having rupturing capacity upto 250 MVA, overload and earth fault protection, ammeter, voltmeter and of rating upto 400 Amp
Each 9,09,150
56 -- do -- but rupturing capacity 350 MVA of rating upto 630 Amp
Each 10,04,370
SF6 CIRCUIT BREAKER
(INDOOR)
57
Supply and installation of HT 11 KV ,3 phase, 50 cycles totally enclosed metal clad SF6 switchgear having rupturing capacity upto 250 MVA, overload and earth fault protection, ammeter, voltmeter and of rating upto 400 Amp
Each 9,55,152
58 -- do -- but rupturing capacity 350 MVA of rating upto 630 Amp
Each 10,56,212
59
Supply and installation of HT 33 KV, 3 phase, 50 cycles totally enclosed metal clad SF6 switchgear having rupturing capacity upto 250 MVA, overload and earth fault protection, ammeter, voltmeter and of rating upto 400 Amp
Each 14,62,030
60 -- do -- but rupturing capacity 350 MVA of rating upto 630 Amp
Each 15,18,717
(OUTDOOR)
61 Supply and installation of Ring main unit one incoming two outgoing SF6 filled load break switch each of 11 KV ,630 Amp
Each 11,26,569
62
Supply and installation of HT 11 KV, 3 phase, 50 cycles, totally enclosed metal clad SF6 Switchgear having Rupturing capacity upto 250 MVA, overload and earth fault protection, ammeter, voltmeter and of rating upto 400 Amp
Each 11,66,858
63 -- do -- but rupturing capacity 350 MVA of rating upto 630 Amp
Each 13,56,007
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 13 of 117
Item No Description of Item Unit Rate
64
Supply and installation of HT 33 KV ,3 phase, 50 cycles totally enclosed metal clad SF6 Switchgear having Rupturing capacity upto 250 MVA, overload and earth fault protection, ammeter, voltmeter and of rating upto 400 Amp
Each 16,04,426
65 -- do -- but rupturing capacity 350 MVA of rating upto 630 Amp
Each 16,83,247
Note FOR CTs and PTs : add prices from item No. 66 to 73 in relevant item of switchgear
HT CTs & PTs
66 Supply and installation of 11 KV, single phase, out door oil cooled CT of ratio 400/5-5 Amp, class 1.0 / 5P10, burden 15 VA
Set of 3 1,01,198
67 -- do -- but for 33 KV Set of 3 1,46,671
68
Supply and installation of 11 KV single phase out door oil cooled PT of ratio 11 KV/rt3/110 V/rt3/110V/rt3,Class 0.5-3, Burden 50 VA – 50 VA
Set of 3 95,199
69 -- do -- but for 33 KV Set of 3 1,45,602
70 Supply and installation of 11 KV single phase in door resin cast CT of ratio 400/5-5A class 1.0/ 5P10,burden 15VA – 15 VA
Set of 3 53,345
71 -- do -- but for 33 KV voltage Set of 3 1,21,343
72
Supply and installation of 11 KV single phase in door resin cast PT of ratio 11 KV/rt3/110 V/rt3/110V/rt3,Class 0.5-3, Burden 50 VA – 50 VA
Set of 3 73,193
73 -- do -- but for 33 KV Set of 3 1,27,712
COMPACT SUB STATION(CSS)
74
Supply and Installation of 11 KV Compact Sub Station with non extensible RMU consisting of 1 No manually operated 11 KV/630 Amps VCB in SF6 insulated stainless enclosure,HT Cable/Bus bar ,1 No transformer 100 KVA,11KV/433 CRT dry type & associated LT devices(ACB/MCCB/bus bar/Cable)
Each 13,36,384
75 .--do-- but transformer of 315 KVA Each 18,89,250
76 .--do-- but transformer of 500 KVA Each 22,53,502
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 14 of 117
Item No Description of Item Unit Rate
77 .--do-- but transformer of 630 KVA Each 24,95,781
78 .--do-- but transformer of 1000 KVA Each 32,94,789
79 .--do-- but transformer of 1250 KVA Each 37,31,558
80 .--do-- but transformer of 1600 KVA Each 43,49,844
81 .--do-- but transformer of 2000 KVA Each 50,17,531
Note: CSS rate are inclusive of foundation and plinth
LOAD BREAK SWITCH
82 Supply and Installation of11 KV, 630 Amp Load break switch with earth switch
Each 1,57,642
83 Supply and Installation of11 KV, 630 Amp Load break switch with 200 Amp DO set and earth switch
Each 2,04,935
GANG OPERATED AIR BREAK SWITCHES (GOD)
84
Supply and fix HT 11 KV, out door type gang operated air-break switch suitable for horizontal or vertical mounting fixed type complete with 9 insulators of rating upto 200 Amps
Each 26,355
85 -do- but 400 Amps Each 27,889
86 -do- but 630 Amps Each 29,751
87
Supply and fix HT 11 KV out door type gang operated air-break switch suitable for horizontal or vertical mounting rotating type complete with 9 insulators of rating upto 200 Amps
Each 30,608
88 -do- but 400 Amps Each 43,992
89
Supply and fix HT 11 KV out door type gang operated air-break switch suitable for horizontal or vertical mounting rotating type complete with drop out fuse having 12 insulators of rating upto 200 Amps
Each 44,299
90 -do- but 400 Amps Each 50,054
91
Supply and fix HT 33 KV out door type gang operated air-break switch suitable for horizontal or vertical mounting fixed type complete with 9 insulators of rating upto 200 Amps
Each 62,264
92 -do- but 400 Amps Each 69,797
93
Supply and fix HT 33 KV out door gang operated air-break switch 9 insulator rocking type horizontal mounting of 200/400 Amps rating
Each 77,637
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 15 of 117
Item No Description of Item Unit Rate
94
Supply and fix HT 33 KV out door type gang operated air-break switch suitable for horizontal or vertical mounting fixed type complete with 9 insulators and with earth switch upto 200/400 Amps
Each 82,345
Note:— Cost of GOD includes cost of GI pipe required for operation
Rubber Mat and Hand Glove
95 Rubber mat of 1 meter x 2 meter x 10 mm Each 2,899
96 Rubber mat of 1 meter x 2 meter x 19 mm Each 5,375
97 Electric rubber hand gloves 11 KV Each 900
98 Electric rubber hand gloves 33 KV Each 2,169
LT SWITCH GEAR
99
Supply & fix LT switch gear 440 Volts 3 phase, 4 wire 50 cycles, cubicle or truck type complete with air circuit breaker, overload protection, no-volt release with necessary CTs,meter and cable boxes of rating upto 800 Amps
Each 2,71,716
100 -do- but of rating 1000 Amps Each 2,84,581
101 -do- but of rating 1250 Amps Each 3,17,972
102 -do- but of rating 1600 Amps Each 3,46,136
103
Supply and fix LT synchronizing panel complete with synchroscope, voltmeter, frequency meter load sharing relay and other accessories and complete with internal wiring up to 160 KVA
Each 61,238
104 -do- but exceeding 160 KVA Each 76,388
COMPACT AIR INSULATED RISING MAINS
(ALUMINIUM BUS BAR)
105
Supply and fix compact air insulated rising main with aluminium busbar 125 Amps,breaking capacity of 35 KA and IP 54 protection
RM 15,130
106
Supply and fix compact air insulated rising main with aluminium busbar 200 Amp,breaking capacity of 35 KA and IP 54 protection
RM 18,039
107
Supply and fix compact air insulated rising main with aluminium busbar 315 Amps,breaking capacity of 35 KA and IP 54 protection
RM 19,320
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 16 of 117
Item No Description of Item Unit Rate
108
Supply and fix compact air insulated rising main with aluminium busbar 400 Amps having, breaking capacity of 35 KA and IP 54 protection
RM 20,483
109
Supply and fix compact air insulated rising main with aluminium busbar 500 Amps,breaking capacity of 35 KA and IP 54 protection
RM 22,695
110
Supply and fix compact air insulated rising main with aluminium busbar 630 Amps,breaking capacity of 35 KA and IP 54 protection
RM 24,673
111
Supply and fix compact air insulated rising main with aluminium busbar 800 Amps,breaking capacity of 35 KA and IP 54 protection
RM 33,751
112
Supply and fix compact air insulated rising main with aluminium busbar 1000 Amps,breaking capacity of 35 KA and IP 54 protection
RM 42,130
113
Supply and fix compact air insulated rising main with aluminium busbar 1250 Amps,breaking capacity of 35 KA and IP 54 protection
RM 45,738
(COPPER BUS BAR)
114
Supply and fix compact air insulated rising main with copper busbar 125 Amps,breaking capacity of 35 KA and IP 54 protection
RM 20,483
115
Supply and fix compact air insulated rising main with copper busbar 200 Amps,breaking capacity of 35 KA and IP 54 protection
RM 20,483
116
Supply and fix compact air insulated rising main with copper busbar 315 Amps,breaking capacity of 35 KA and IP 54 protection
RM 28,281
117
Supply and fix compact air insulated rising main with copper busbar 400 Amps,breaking capacity of 35 KA and IP 54 protection
RM 29,445
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 17 of 117
Item No Description of Item Unit Rate
118
Supply and fix compact air insulated rising main with copper busbar 500 Amps ,breaking capacity of 35 KA and IP 54 protection
RM 33,634
119
Supply and fix compact air insulated rising main with copper busbar 630 Amps,breaking capacity of 35 KA and IP 54 protection
RM 38,639
120
Supply and fix compact air insulated rising main with copper busbar 800 Amps,breaking capacity of 35 KA and IP 54 protection
RM 54,699
121
Supply and fix compact air insulated rising main with copper busbar 1000 Amps ,breaking capacity of 35 KA and IP 54 protection
RM 70,527
122
Supply and fix compact air insulated rising main with copper busbar 1250 Amps,breaking capacity of 35 KA and IP 54 protection
RM 80,070
Note: Item No 105-122 Rates include cost of 4P MCCBs of suitable capacity,separators,flexible joints,tap off boxes,end feed units,earthing etc.
COMPACT AIR INSULATED BUS TRUNKING
(ALUMINIUM BUS BAR)
123
Supply and fix compact air insulated bus bar trunking system with aluminium busbar 630 Amps, 50 KA breaking capacity,IP 54 protection
RM 11,638
124
Supply and fix compact air insulated bus bar trunking system with aluminium busbar 800 Amps,50 KA breaking capacity,IP 54 protection
RM 15,130
125
Supply and fix compact air insulated bus bar trunking system with aluminium busbar 1000 Amps,50 KA breaking capacity,IP 54 protection
RM 18,039
126
Supply and fix compact air insulated bus bar trunking system with aluminium busbar 1250 Amps,50 KA breaking capacity,IP 54 protection
RM 21,531
(COPPER BUS BAR)
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 18 of 117
Item No Description of Item Unit Rate
127
Supply and fix compact air insulated bus bar trunking system with copper busbar 630 Amps,50 KA breaking capacity,IP 54 protection
RM 28,281
128
Supply and fix compact air insulated bus bar trunking system with copper busbar 800 Amps,50 KA breaking capacity,IP 54 protection
RM 36,893
129
Supply and fix compact air insulated bus bar trunking system with copper busbar 1000 Amps,50 KA breaking capacity,IP 54 protection
RM 46,669
130
Supply and fix compact air insulated bus bar trunking system with copper busbar 1250 Amps,50 KA breaking capacity,IP 54 protection
RM 53,768
SANDWICH TYPE BUS TRUNKING
(ALUMINIUM BUS BAR)
131 Supply and fix sandwich type bus trunking system with aluminium busbar 630 Amps,50 KA breaking capacity,IP 54 protection
RM 13,035
132 Supply and fix sandwich type bus trunking system with aluminium busbar 800 Amps,50 KA breaking capacity,IP 54 protection
RM 15,828
133
Supply and fix sandwich type bus trunking system with aluminium busbar 1000 Amps,50 KA breaking capacity,IP 54 protection
RM 17,807
134
Supply and fix sandwich type bus trunking system with aluminium busbar 1250 Amps,50 KA breaking capacity,IP 54 protection
RM 20,367
135
Supply and fix sandwich type bus trunking system with aluminium busbar 1600 Amps,50 KA breaking capacity,IP 54 protection
RM 25,488
136
Supply and fix sandwich type bus trunking system with aluminium busbar 2000 Amps,50 KA breaking capacity,IP 54 protection
RM 29,910
(COPPER BUS BAR)
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 19 of 117
Item No Description of Item Unit Rate
137 Supply and fix sandwich type bus trunking system with copper busbar 630 Amps,50 KA breaking capacity,IP 54 protection
RM 36,660
138 Supply and fix sandwich type bus trunking system with copper busbar 800 Amps,50 KA breaking capacity,IP 54 protection
RM 43,876
139 Supply and fix sandwich type bus trunking system with copper busbar 1000 Amps,50 KA breaking capacity,IP 54 protection
RM 58,772
140 Supply and fix sandwich type bus trunking system with copper busbar 1250 Amps,50 KA breaking capacity,IP 54 protection
RM 78,557
141 Supply and fix sandwich type bus trunking system with copper busbar 1600 Amps,50 KA breaking capacity,IP 54 protection
RM 91,359
142 Supply and fix sandwich type bus trunking system with copper busbar 2000 Amps,50 KA breaking capacity,IP 54 protection
RM 1,24,062
NOTE: Item No 123-142 Rates include cost of separators,flexible joints,tap off boxes,end feed units,earthing etc.
PLUG IN BOXES FOR RISING MAIN/ BUS BAR TRUNKING TO BRANCH OUT CONNECTION
143 Supply and fix 4 pole plug in box 100 Amp with MCCB 35/50 KA
Each 55,651
144 Supply and fix 4 pole plug in box 250 Amp with MCCB 35/50KA
Each 1,04,023
145 Supply and fix 4 pole plug in box 315 Amp with MCCB 35/50 KA
Each 1,10,477
146 Supply and fix 4 pole plug in box 400 Amp with MCCB 35/50 KA
Each 1,24,294
147 Supply and fix 4 pole plug in box 630 Amp with MCCB 35/50 KA
Each 1,82,527
148 Supply and fix 4 pole plug in box 800 Amp with MCCB 35/50 KA
Each 2,92,823
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 20 of 117
Item No Description of Item Unit Rate
POWER FACTOR IMPROVEMENT CAPACITOR Note:— To decide type of capacitor to be used, first find out percentage of non linear load in the system as worked out below and then select the type of capacitor as given in table:—. Example Calculation for percentage non linear loads TRANSFORMER CAPACITY --- 1000 KVA UPS LOAD --- 10 KVA AC DRIVE --- 50 KVA WELDING LOAD — 40 KVA TOTAL NON LINEAR LOAD --- 100 KVA PERCENTAGE NON LINEAR LOAD = 100/1000=10% PERMISSIBLE LOADS Type of Capacitor Permissible percentage (Non linear loads) MPP-S 10%, MPP-H 15% , MPP-XL 20%, FILTER REACTOR + MD-XL CAPACITOR Above 20% & upto 50%
MPP-H CAPACITOR
149
Supply and fix capacitor metalized poly propylene heavy duty (MPP-H) for 3 phase ,440 V, 50 Hz System for permissible non- linear load 15% of 5 KVAR capacity.
Each 3,069
150 -- Do -- but of 7.5 KVAR capacity Each 4,307
151 -- Do -- but of 10 KVAR capacity Each 5,460
152 -- Do -- but of 15 KVAR capacity Each 8,041
153 -- Do -- but of 20 KVAR capacity Each 10,422
154 -- Do -- but of 25 KVAR capacity Each 12,580
155 -- Do -- but of 30 KVAR capacity Each 14,950
156 -- Do -- but of 40 (20 x 2) KVAR capacity Each 20,018
157 -- Do -- but of 50 (25 x 2) KVAR capacity Each 24,938
158 -- Do -- but of 60 (30 x 2) KVAR capacity Each 29,688
159 -- Do -- but of 75 (25 x 3) KVAR capacity Each 37,877
160 -- Do -- but of 80 (20 x 4) KVAR capacity Each 40,257
161 -- Do -- but of 100 ( 25 x 4) KVAR capacity Each 50,478
APFC PANEL WITH MPP-H CAPACITOR AND MCCB AS INCOMER
162 Supply and install 100 KVAR with 5 steps (50 + 25 + 15 + 5 + 5)
Each 4,96,869
163 125 KVAR with 5 steps (2x12.5 + 2x25 + 50) Each 5,61,925
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 21 of 117
Item No Description of Item Unit Rate
164 150 KVAR with 6 steps (2x12.5 + 3x25 + 50)
Each 6,35,763
165 175 KVAR with 6 steps (2x12.5 + 2x25 + 2x50)
Each 6,91,181
166 200 KVAR with 6 steps (2x12.5 + 1x25 + 3x50)
Each 7,74,636
167 225 KVAR with 6 steps (2x12.5 + 4x50) Each 7,83,069
168 250 KVAR with 6 steps (2x25 + 4x50) Each 8,90,688
169 275 KVAR with 6 steps (1x100 + 3x50 + 2x12.5)
Each 9,82,681
170 300 KVAR with 6 steps (1x100 + 3x50 + 2x25)
Each 10,31,593
171 350 KVAR with 8 steps (1x100 + 3x50 + 4x25)
Each 12,28,656
172 400 KVAR with 8 steps (2x100 + 2x50 + 4x25)
Each 14,11,150
173 450 KVAR with 8 steps (2x100 + 4x50 + 2x25)
Each 15,38,914
CAPACITOR MPP-S
174
Supply and fix capacitor metalized poly propylene Type — S (MPP—S) for 3 phase , 440 V,50 Hz System for permissible non- linear load 10% of capacity 5 KVAR
Each 2,296
175 -- do -- but of 7.5 KVAR capacity Each 3,143
176 -- do -- but of 10 KVAR capacity Each 3,926
177 -- do-- but of 15 KVAR capacity Each 5,724
178 -- do-- but of capacity 20 KVAR Each 7,396
179 -- do-- but of 25 KVAR capacity Each 9,078
180 -- do-- but of 30 KVAR capacity Each 10,951
181 -- do -- but of 40 (20 x 2) KVAR capacity Each 14,611
182 -- do -- but of 50 (25 x 2) KVAR capacity Each 18,209
183 -- do-- but of 60 (20 x 3) KVAR capacity Each 21,171
184 -- do-- but of 75 (25 x 3) KVAR capacity Each 27,329
185 -- do-- but of 80 (20 x 4) KVAR capacity Each 28,143
186 -- do-- but of 100 ( 25 x 4) KVAR capacity Each 36,427
CAPACITOR MD—XL
187
Supply and fix MD—XL Double metalized paper (Extra Low Loss) Capacitor for 3 phase, 440 V, 50 Hz system for permissible non- leaner load 20% of capacity 5 KVAR
Each 4,497
188 -- do-- but of 7.5 KVAR capacity Each 6,444
189 -- do-- but of 10 KVAR capacity Each 8,380
190 -- do-- but of 15 KVAR capacity Each 12,294
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 22 of 117
Item No Description of Item Unit Rate
191 -- do-- but of 20 KVAR capacity Each 16,072
192 -- do-- but of 25 KVAR capacity Each 19,923
193 -- do-- but of 30 KVAR capacity Each 23,848
194 -- do-- but of 40 (20 x 2) KVAR capacity Each 32,523
195 -- do-- but of 50 (25 x 2) KVAR capacity Each 40,575
196 -- do-- but of 60 (30 x 2) KVAR capacity Each 47,388
197 -- do-- but of 75 (25 x 3) KVAR capacity Each 60,634
198 -- do-- but of 80 (20 x 4) KVAR capacity Each 62,814
199 -- do-- but of 100 ( 25 x 4) KVAR capacity Each 80,832
APFC PANEL WITH MD-XL CAPACITOR AND MCCB AS INCOMER
200 Supply and install 100 KVAR with 5 steps (50 + 25 + 15 + 5 + 5)
Each 5,83,657
201 125 KVAR with 5 steps (2x12.5 + 2x25 + 50)
Each 6,24,443
202 150 KVAR with 6 steps (2x12.5 + 3x25 + 50)
Each 7,18,055
203 175 KVAR with 6 steps (2x12.5 + 2x25 + 2x50)
Each 7,76,266
204 200 KVAR with 6 steps (2x12.5 + 1x25 + 3x50)
Each 8,32,541
205 225 KVAR with 6 steps (2x12.5 + 4x50) Each 8,80,415
206 250 KVAR with 6 steps (2x25 + 4x50) Each 9,40,086
207 275 KVAR with 6 steps (1x100 + 3x50 + 2x12.5)
Each 9,95,303
208 300 KVAR with 6 steps (1x100 + 3x50 + 2x25)
Each 10,37,793
209 350 KVAR with 8 steps (1x100 + 3x50 + 4x25)
Each 12,44,198
210 400 KVAR with 8 steps (2x100 + 2x50 + 4x25)
Each 14,02,411
211 450 KVAR with 8 steps (2x100 + 4x50 + 2x25)
Each 15,12,814
HT 11 KV CAPACITOR
212
Supply and fix power factor improvement single phase static 12 KV capacitor with manual control up to 60 KVAR (180 KVAR in three phase)
KVAR 371
213 -- do -- but exceeding 60 KVAR KVAR 360
LT SWITCHES
(SUITABLE FOR EXTERNAL MOUNTING)
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 23 of 117
Item No Description of Item Unit Rate
214
Supply and fix switch with sheet steel enclosure 500 V, 3 phase with HRC fuses complete with Neutral link of capacity 32 Amps.
Each 4,412
215 -- do -- but of capacity 63 Amps Each 5,312
216 -- do -- - but of capacity 100 Amps Each 8,803
217 -- do -- but of capacity 125 Amps Each 9,946
218 -- do -- but of capacity 160 Amps Each 11,448
219 -- do -- but of capacity 200 Amps Each 13,405
220 -- do -- but of capacity 250 Amps Each 15,765
221 -- do -- but of capacity 315 Amps Each 19,256
222 -- do -- but of capacity 400 Amps Each 23,033
LT SWITCHES
SWITCH FUSE UNIT SUITABLE FOR INTERNAL MOUNTING IN PANEL
223
Supply and fix switch fuse unit TPN 500 Volts, 3 phase with HRC fuses suitable for interior mounting in panel of capacity 32 Amp .
Each 2,550
224 -- do -- but of capacity 63 Amps TPN Each 3,249
225 -- do -- but of capacity 100 Amps TPN Each 6,550
226 -- do -- but of capacity 125 Amps TPN Each 7,756
227 -- do -- but of capacity 250 Amps TPN Each 12,369
228 -- do -- but of capacity 400 Amps TPN Each 19,256
RESIDUAL CURRENT CIRCUIT BREAKER (RCCB)
229 Supply and fix RCCB of 2 pole , 25 Amp rating with sensitivity of 30 mA suitable for 240 Volts .
Each 3,323
230 -- do -- but for 40 Amp Each 3,587
231 -- do -- but for 63 Amp Each 4,444
232 Supply and fix RCCB of 4 pole , 25 Amp rating with sensitivity of 30 mA suitable for 415 Volts
Each 4,275
233 -- do -- but for 40 Amp Each 4,285
234 -- do -- but for 63 Amp Each 4,772
RCCB WITH OVER LOAD AND SHORT CIRCUIT (RCCB+MCB)
235 Supply and fix RCCB with MCB of 2 pole , 6 Amp rating with sensitivity of 30 mA suitable for 240 Volts
Each 3,957
236 -- do -- but for 10 Amp Each 3,957
237 -- do -- but for 16 Amp Each 3,915
238 -- do -- but for 20 Amp Each 3,915
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 24 of 117
Item No Description of Item Unit Rate
239 -- do -- but for 25Amp Each 3,915
240 -- do -- but for 32 Amp Each 4,031
241 -- do -- but for 40 Amp Each 4,592
MOULDED CASE CIRCUIT BREAKER (MCCB)
WITH THERMAL BASED RELEASE 3 POLE
242 Supply and fix 3 Pole MCCB 32 to 100 Amp, 50 Hz, 415 V with rupturing capacity 10 KA.
Each 2,772
243 3 Pole MCCB 12 to 63 Amp, 50 Hz, 415 V with rupturing capacity 25 KA
Each 6,137
244 3 Pole MCCB 63 to 100 Amp, 50 Hz, 415 V with rupturing capacity 25 KA
Each 6,380
245 3 Pole MCCB 100 to 125 Amp, 50 Hz, 415 V with rupturing capacity 35 KA.
Each 9,480
246 3 Pole MCCB 125 to160 Amp, 50 Hz, 415 V with rupturing capacity 35 KA.
Each 11,850
247 3 Pole MCCB 160 to 200 Amp, 50 Hz, 415 V with rupturing capacity 35 KA.
Each 15,595
248 3 Pole MCCB 200 to 250 Amp, 50 Hz, 415 V with rupturing capacity 35 KA.
Each 18,717
4 POLE MCCB
249 Supply and fix 4 Pole MCCB 12 to 63 Amp, 50 Hz, 415 V with rupturing capacity 25 KA
Each 7,576
250 4 Pole MCCB 63 to 100 Amp, 50 Hz, 415 V with rupturing capacity 25 KA.
Each 7,998
251 4 Pole MCCB 100 to 125 Amp, 50 Hz, 415 V with rupturing capacity 35 KA.
Each 11,882
252 4 Pole MCCB 125 to 160 Amp, 50 Hz, 415 V with rupturing capacity 35 KA.
Each 14,961
253 4 Pole MCCB 160 to 200 Amp, 50 Hz, 415 V with rupturing capacity 35 KA
Each 19,531
254 4 Pole MCCB 200 to 250 Amp, 50 Hz, 415 V with rupturing capacity 35 KA.
Each 23,774
255 4 Pole MCCB 250 to 320 Amp, 50 Hz, 415 V with rupturing capacity 35 KA
Each 39,411
256 4 Pole MCCB 320 to 400 Amp, 50 Hz, 415 V with rupturing capacity 36 KA
Each 33,148
257 4 Pole MCCB 400 to 500 Amp, 50 Hz, 415 V with rupturing capacity 35 KA
Each 39,474
HIGH BREAKING CAPACITY MCCB
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 25 of 117
Item No Description of Item Unit Rate
258 Supply and fix 3 Pole MCCB 100 to 125 Amp, 50 Hz, 415 V with rupturing capacity 50 KA
Each 9,371
259 Supply and fix 3 Pole MCCB 125 to 160 Amp, 50 Hz 415 V with rupturing capacity 50 KA
Each 11,053
260 Supply and fix 3 Pole MCCB 160 to 200 Amp, 50 Hz ,415 V with rupturing capacity 50 KA
Each 13,040
261 Supply and fix 3 Pole MCCB 200 to 250 Amp 50 Hz 415 V with rupturing capacity 50 KA
Each 15,846
262 Supply and fix 3 Pole MCCB 250 to 320 Amp, 50 Hz, 415 V with rupturing capacity 50 KA
Each 28,609
263 Supply and fix 4 Pole MCCB 100 to 125 Amp, 50 Hz, 415 V with rupturing capacity 50 KA
Each 26,302
264 Supply and fix 4 Pole MCCB 125 to 160 Amp, 50 Hz, 415 V with rupturing capacity 50 KA
Each 26,715
265 Supply and fix 4 Pole MCCB 160 to 200 Amp,50 Hz, 415 V with rupturing capacity 50 KA
Each 27,255
266 Supply and fix 4 Pole MCCB 200 to 250 Amp, 50 Hz, 415 V with rupturing capacity 50 KA
Each 28,143
267 Supply and fix 4 Pole MCCB 250 to 320 Amp, 50 Hz, 415 V with rupturing capacity 50 KA
Each 37,538
268 Supply and fix 4 Pole MCCB 320 to 400 Amp, 50 Hz ,415 V with rupturing capacity 50 KA
Each 37,538
269 Supply and fix 4 Pole MCCB 400 to 500 Amp, 50 Hz, 415 V with rupturing capacity 50 KA
Each 37,538
270 Supply and fix 4 Pole MCCB 500 to 630 Amp, 50 Hz ,415 V with rupturing capacity 50 KA
Each 49,928
MCCB WITH MICROPROCESSOR BASED RELEASE
271 Supply and fix 3 Pole MCCB 63 Amp ,50Hz, 415 V with rupturing capacity 35 KA
Each 14,992
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 26 of 117
Item No Description of Item Unit Rate
272 Supply and fix 3 Pole MCCB 160 Amp ,50Hz, 415 V with rupturing capacity 35 KA
Each 20,547
273 Supply and fix 3 Pole MCCB 250 Amp ,50Hz, 415 V with rupturing capacity 35 KA
Each 26,239
274 Supply and fix 3 Pole MCCB 400 Amp ,50Hz ,415 V with rupturing capacity 35 KA
Each 31,984
275 Supply and fix 3 Pole MCCB 630 Amp ,50Hz, 415 V with rupturing capacity 35 KA
Each 35,570
276 Supply and fix 4 Pole MCCB 63 Amp ,50Hz, 415 V with rupturing capacity 35 KA
Each 21,086
277 Supply and fix 4 Pole MCCB 160 Amp ,50Hz, 415 V with rupturing capacity 35 KA
Each 26,842
278 4 Pole MCCB 250 Amp ,50Hz, 415 V with rupturing capacity 35 KA
Each 33,126
279 Supply and fix4 Pole MCCB 400 Amp ,50Hz ,415 V with rupturing capacity 35 KA
Each 39,919
280 Supply and fix 4 Pole MCCB 600 Amp ,50Hz, 415 V with rupturing capacity 35 KA
Each 48,986
ON LOAD CHANGE OVER SWITCH TPN VERSION
281 Supply and fix ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 63 Amps.
Each 7,999
282 - do -- but of capacity 125 Amps. Each 13,765
283 -- do -- but of capacity 160 Amps. Each 15,669
284 -- do -- but of capacity 200 Amps. Each 17,320
285 -- do -- but of capacity 250 Amps. Each 23,329
286 -- do -- but of capacity 315 Amps. Each 24,768
287 -- do -- but of capacity 400 Amps. Each 35,687
288 -- do -- but of capacity 630 Amps. Each 41,675
INDUSTRIAL WALL MOUNTED PLUG SOCKET SUITABLE FOR IP44 DEGREE OF PROTECTION
289 Supply and fix 16 Amps rating 2P+E Each 900
290 -- do -- but 3P+E Each 1,016
291 -- do -- but 3P+N+E Each 1,016
292 Supply and fix 32 Amps rating 2P+E Each 1,080
293 -- do -- but 3P+E Each 1,207
294 -- do -- but 3P+N+E Each 1,207
INDUSTRIAL WALL MOUNTED PLUG SOCKET SUITABLE FOR IP67 DEGREE OF PROTECTION
295 Supply and fix 16 Amps rating 2P+E Each 1,260
296 -- Do -- but 3P+E Each 1,418
297 -- Do -- but 3P+N+E Each 1,450
298 Supply and fix 32 Amps rating 2P+E Each 1,450
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 27 of 117
Item No Description of Item Unit Rate
299 -- Do -- but 3P+E Each 1,778
300 -- Do -- but 3P+N+E Each 2,106
INDUSTRIAL PANEL MOUNTED PLUG SOCKET SUITABLE FOR IP44 DEGREE OF PROTECTION
301 Supply and fix 16 Amps rating 2P+E Each 805
302 -- do -- but 3P+E Each 953
303 -- do -- but 3P+N+E Each 963
304 Supply and fix 32 Amps rating 2P+E Each 984
305 -- do -- but 3P+E Each 1,080
306 -- do -- but 3P+N+E Each 1,080
INDUSTRIAL PANEL MOUNTED PLUG SOCKET SUITABLE FOR IP67 DEGREE OF PROTECTION
307 Supply and fix 16 Amps rating 2P+E Each 1,122
308 -- do -- but 3P+E Each 1,164
309 -- do -- but 3P+N+E Each 1,164
310 Supply and fix 32 Amps rating 2P+E Each 1,323
311 -- do -- but 3P+E Each 1,365
312 -- do -- but 3P+N+E Each 1,397
METAL PLUG AND SOCKET WITH MCB AND STEEL ENCLOSURE
313 Supply and fix 20 Amps SPN MCB metallic P&S
Each 1,418
314 Supply and fix 20 Amps TP MCB metallic P&S
Each 3,111
315 Supply and fix 32 Amps TP MCB metallic P&S
Each 3,651
316 Supply and fix 20 Amps SPN AC Box Each 1,408
VOLTAGE STABILISER
317
Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 0 .5 KVA
Each 3,196
318 -- do -- but of capacity 1.0 KVA Each 6,454
319 -- do -- but of capacity 2.0 KVA Each 7,745
320 -- do -- but of capacity 3.0 KVA Each 8,972
321 -- do -- but of capacity 4.0 KVA Each 10,655
322 -- do -- but of capacity 5.0 KVA Each 11,607
SERVO CONTROLLED OIL COOLED STABILIZER
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 28 of 117
Item No Description of Item Unit Rate
323
Supply and fix Voltage stabilizer for automatic operation, three phase, naturally oil cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 10 KVA
Each 74,367
324 -- do -- but of capacity 15 KVA Each 82,271
325 -- do -- but of capacity 20 KVA Each 95,813
326 -- do -- but of capacity 25 KVA Each 1,13,164
327 -- do -- but of capacity 30 KVA Each 1,31,806
328 -- do -- but of capacity 50 KVA Each 1,95,191
329 -- do -- but of capacity 75 KVA Each 2,74,562
330 -- do -- but of capacity 100 KVA Each 3,20,585
331 -- do -- but of capacity 150 KVA Each 4,56,379
332 -- do -- but of capacity 200 KVA Each 5,38,872
333 -- do -- but of capacity 250 KVA Each 6,39,466
334 -- do -- but of capacity 300 KVA Each 7,24,297
335 -- do -- but of capacity 400 KVA Each 10,35,211
336 -- do -- but of capacity 500 KVA Each 13,29,007
337 -- do -- but of capacity 1000 KVA Each 21,89,013
338 -- do -- but of capacity 1500 KVA Each 28,96,117
339 -- do -- but of capacity 2000 KVA Each 39,42,891
UPS
340 Supply and fix UPS for 30 min back up single phase AC input 160 to 260 V and out put 230 ± 1% of capacity 1KVA
Each 33,931
341 -- do-- but of capacity 2 KVA Each 65,501
342 -- do-- but of capacity 3 KVA Each 78,578
343 -- do-- but of capacity 5 KVA Each 1,26,474
344 Supply and fix UPS for 30 min back up three phase AC input 300 to 450V and out put 415 V ± 1% of capacity 7.5 KVA
Each 4,62,812
345 -- do-- but of capacity 10 KVA Each 5,79,023
346 -- do-- but of capacity 15 KVA Each 6,37,922
347 -- do-- but of capacity 20 KVA Each 6,55,971
348 -- do-- but of capacity 30 KVA Each 9,68,801
349
Supply and fix UPS for 30 min back up three phase AC input 300 to 450V and out put single phase AC out put Voltage 230 V ± 1% of capacity 7.5 KVA
Each 2,16,700
350 -- do-- but of capacity 10 KVA Each 2,31,078
351 -- do-- but of capacity 15 KVA Each 3,10,809
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 29 of 117
Item No Description of Item Unit Rate
352 -do – but of capacity 20 KVA Each 3,55,266
353 -do – but of capacity 30 KVA Each 7,24,889
ARMOURED XLPE CABLES (LT) 1.1 KV GRADE
354
Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 2 core
RM 318
355 do-- but size 10 sq mm 2 core RM 350
356 -- do-- but size 16 sq mm 2 core RM 392
357 -- do-- but size 25 sq mm 2 core RM 392
358 - do-- but size 35 sq mm 2 core RM 445
359 -- do-- but size 6 sq mm 4 core RM 360
360 -- do-- but size 10 sq mm 4 core RM 413
361 -- do-- but size 16 sq mm 4 core RM 434
362 -- do-- but size 25 sq mm 4 core RM 540
363 -- do-- but size 35 sq mm 3½ core RM 593
364 -- do-- but size 50 sq mm 3½ core RM 699
365 -- do-- but size 70 sq mm 3½ core RM 879
366 -- do-- but size 95 sq mm 3½ core RM 1,069
367 -- do-- but size 120 sq mm 3½ core RM 1,344
368 -- do-- but size 150 sq mm 3½ core RM 1,545
369 -- do-- but size 185 sq mm 3½ core RM 1,873
370 -- do-- but size 240 sq 3½ core RM 2,307
371 -- do-- but size 300 sq mm 3½ core RM 2,772
372 -- do-- but size 400 sq mm 3½ core RM 3,492
373 -- do-- but size 500 sq mm 3½ core RM 4,476
Note: Item No 354-373 Rate of under ground cable includes earth Work, sand cushioning, brick or PCC covering, light Grade GI tubing where necessary,testing etc.
ARMOURED XLPE CABLE 11 KV GRADE
374
Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 11000 volts grade, of size 3 core 35 sq mm.
RM 1,323
375 - do-- but of size 50 sq mm RM 1,461
376 -- do-- but of size 70 sq mm RM 1,662
377 -- do-- but of size 95 sq mm RM 1,958
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 30 of 117
Item No Description of Item Unit Rate
378 -- do-- but of size 120 sq mm RM 2,180
379 -- do-- but of size 150 sq mm RM 2,392
380 -- do-- but of size 185 sq mm RM 2,751
381 -- do-- but of size 240 sq mm RM 3,217
382 -- do-- but of size 300 sq mm RM 3,682
383 -- do-- but of size 400 sq mm RM 4,381
Note: Item No 374-383 Rate of under ground cable includes earth Work, sand cushioning, brick or PCC/RCC covering, light Grade GI tubing where necessary,testing etc.
ARMOURED XLPE CABLE 33 KV GRADE
384
Supply, laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 33000 volts grade, of size 3 core 95 sq mm
RM 3,270
385 -- do-- but of size 120 sq mm RM 3,587
386 -- do-- but of size 150 sq mm RM 3,873
387 -- do-- but of size 185 sq mm RM 4,285
388 -- do-- but of size 240 sq mm RM 4,814
389 -- do-- but of size 300 sq mm RM 5,354
Note:Item No 384-389 Rate of under ground cable includes earth Work, sand cushioning, brick or PCC/RCC covering, light Grade GI tubing where necessary,testing etc.
CONTROL CABLE COPPER CONDUCTOR
390
Supply, laying & testing PVC insulated, PVC sheathed cable galvanized steel strip or wire armoured, electric control cables (Heavy duty) with stranded copper conductor of size 1.5 sq mm ,2 core, 1100 Volts grade.
RM 318
391 do-- but size 2 Core ,2.5 ,Sq mm RM 371
392 -- do-- but size 2 Core, 4 Sq mm RM 434
393 -- do-- but size 3 Core, 1.5 Sq mm RM 360
394 -- do-- but size 3 Core ,2.5 Sq mm RM 424
395 -- do-- but size 3 Core ,4 Sq mm RM 508
396 -- do-- but size 4 Core, 1.5 Sq mm RM 403
397 -- do-- but size 4 Core ,2.5 Sq mm RM 477
398 -- do-- but size 4 Core, 4 Sq mm RM 604
399 -- do-- but size 5 Core, 1.5 Sq mm RM 434
400 -- do-- but size 6 Core, 1.5 Sq mm RM 466
401 -- do-- but size 7 Core ,1.5 Sq mm RM 498
402 -- do-- but size 8 Core ,1.5 Sq mm RM 540
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 31 of 117
Item No Description of Item Unit Rate
CABLE JOINTING KIT
403
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 25 to 50 sqmm,Indoor/Outdoor type
Each 5,100
404 -- do-- but for cable of size 70 to 95 sq mm. Each 7,385
405 -- do-- but for cable of size 120 to 150 sq mm.
Each 7,385
406 -- do-- but for cable of size 185 to 240 sq mm
Each 12,972
407 -- do-- but for cable of size 300 to 400 sq mm.
Each 13,670
408
Supply and fix cable jointing kit for 11 KV grade cable for in door termination, heat shrink type, joint complete with jointing material and accessories suitable for3 core XLPE, armoured, Al conductor cable of size 16 sqmm to 50 sqmm
Each 11,374
409 -- do-- but for cable of size 70 to 120 sq mm.
Each 13,501
410 -- do-- but for cable of size 150 to 225 sq mm.
Each 15,744
411 -- do-- but for cable of size 240 to 300 sq mm.
Each 16,421
412 -- do-- but for cable of size 400 sq mm Each 17,468
413
Supply and fix cable jointing kit for 11 KV grade cable for outdoor termination , heat shrink type, joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 16 sqmm to 50 sqmm
Each 17,267
414 -- do-- but for cable of size 70 to 120 sq mm
Each 19,044
415 -- do-- but for cable of size 150 to 225 sq mm
Each 20,229
416 -- do-- but for cable of size 240 to 300 sq mm
Each 22,705
417 -- do-- but for cable of size 400 sq mm Each 23,784
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 32 of 117
Item No Description of Item Unit Rate
418
Supply and fix cable jointing kit for 33 KV grade cable for in door termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured ,Al conductor cable of size 25 sqmm to 50 sqmm
Each 21,362
419 -- do-- but for cable of size 70 to 95 sq mm. Each 22,494
420 -- do-- but for cable of size 120 to 185 sq mm.
Each 32,365
421 -- do-- but for cable of size 240 to 400 sq mm.
Each 37,327
422
Supply and fix cable jointing kit for 33 KV grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 25 sqmm to 50 sqmm
Each 28,344
423 -- do-- but for cable of size 70 to 95 sq mm Each 34,957
424 -- do-- but for cable of size 120 to 185 sq mm.
Each 44,585
425 -- do-- but for cable of size 240 to 400 sq mm
Each 58,064
426
Supply and fix cable jointing kit for 11 KV grade cable for indoor termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 50 sqmm to 95 sqmm
Each 6,645
427 -- do-- but for cable of size 120 to 185 sq mm.
Each 6,941
428 -- do -- but for cable of size 240 to 400 sq mm.
Each 9,004
429
Supply and fix cable jointing kit for 11 KV grade cable for out door termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 50 Sqmm to 95 Sqmm
Each 11,099
430 -- do-- but for cable of size 120 to 185 sq mm
Each 11,437
431 -- do-- but for cable of size 240 to 400 sq mm
Each 14,125
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 33 of 117
Item No Description of Item Unit Rate
432
Supply and fix cable jointing kit for 11 KV grade cable for straight through cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 50 Sqmm to 95 sqmm, Indoor/Outdoor type
Each 19,171
433 -- do-- but for cable of size 120 to 185 sq mm.
Each 20,505
434 -- Do -- but for cable of size 240 to 400 sq mm
Each 30,058
435
Supply and fix cable jointing kit for 33 KV grade cable for indoor termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured Al conductor cable of size 50 Sqmm to 70 Sqmm
Each 12,474
436 -- do-- but for cable of size 70 to 120 sq mm
Each 16,347
437 -- do-- but for cable of size 150 to 240 sq mm
Each 16,526
438 -- do-- but for cable of size 300 to 400 sq mm
Each 16,738
439
Supply and fix cable jointing kit for 33 KV grade cable for outdoor termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured Al conductor cable of size 50 Sqmm to 120 Sqmm
Each 17,944
440 -- do-- but for cable of size 150 to 240 sq mm
Each 18,463
441 -- do-- but for cable of size 300 to 400 sq mm
Each 19,108
442
Supply and fix cable jointing kit for 33 KV grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured Al conductor cable of size 50 Sqmm to 120 Sqmm, Indoor/Outdoor type
Each 66,337
443 -- do-- but for cable of size 150 to 240 sq mm
Each 1,16,412
444 -- do-- but for cable of size 300 to 400 sq mm
Each 1,29,309
CABLE GLAND
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 34 of 117
Item No Description of Item Unit Rate
445
Supply and fix double compression copper stain less steel gland for fixing armoured cable in panel of size 2 core 6 Sq mm to 16 sq mm size
Each 223
446 -- do-- but for cable of size 25 to 35 sq mm.
Each 392
447 -- do-- but for cable of size 4 core 6 to 16 sq mm above.
Each 297
448 -- do-- but for cable of size 4 core 25 to 35 sq mm Above.
Each 392
449 -- do-- but for cable of size 3½ core 50 sq mm to 70 sq mm above.
Each 540
450 -- do-- but for cable of size 3.5 core 95 sq mm to 120 sqmm
Each 678
451 -- do-- but for cable of size 3.5 core 150 sq mm
Each 921
452 -- do-- but for cable of size 3.5 core 240 sq mm to 300 sq mm above
Each 1,418
453 -- do-- but for cable of size 3 .5 core 400 sq mm
Each 1,767
AERIAL BUNCHED CABLE (ABC)
LT ABC ON PCC POLES
454
Supply and fix LT overhead lines on 9 meter PCC poles with XLPE insulated AB cable 3-core X 50 sq mm + 1-core x 35 sq mm
RM 615
455 do—but of size 3-core X 70 sq mm + 1-core X 50 sq mm
RM 713
456 do—but of size 3-core X 95 sq mm + 1-core X 70 sq mm
RM 815
457 do—but of size 3-core X 120 sq mm X 1-core X 70 sq mm
RM 880
458 do—but of size 3-core X 150 sq mm + 1-core X 95 sq mm
RM 964
459 do—but of size 3-core X 185 sq mm + 1-core X 150 sq mm
RM 1,260
460 do—but of size 3-core X 240 sq mm + 1-core X 185 sq mm
RM 1,500
11 KV HT ABC ON PCC POLES
461 Supply and fix HT overhead lines on 11 meter PCC poles with XLPE insulated AB cable 3-core X 70 sq mm + 1 x 50 sq mm
RM 1,196
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 35 of 117
Item No Description of Item Unit Rate
462 do—but of size 3-core X 95 sq mm + 1 X 70 sq mm
RM 1,347
463 do—but of size 3-core X 185 sq mm + 1-core X 150 sq mm
RM 1,824
LT ABC ON STEEL POLES
464 Supply and fix LT overhead lines on 9 meter steel poles with XLPE insulated AB cable 3-core X 50 sq mm + 1 x 35 sq mm.
RM 1,062
465 do—but of size 3-core X 70 sq mm + 1-core X 50 sq mm
RM 1,159
466 do—but of size 3-core X 95 sq mm + 1-core X 70 sq mm
RM 1,262
467 do—but of size 3-core X 120 sq mm X 1-core X 70 sq mm
RM 1,327
468 do—but of size 3-core X 150 sq mm + 1-core X 95 sq mm
RM 1,410
469 do—but of size 3-core X 185 sq mm + 1-core X 150 sq mm
RM 1,706
470 do—but of size 3-core X 240 sq mm + 1-core X 185 sq mm
RM 1,946
11 KV HT ABC ON STEEL POLES
471 Supply and fix HT overhead lines on 11 meter steel poles with XLPE insulated AB cable 3-core X 70 sq mm + 1 x 50 sq mm.
RM 1,855
472 do—but of size 3-core X 95 sq mm + 1 X 70 sq mm
RM 2,006
473 do—but of size 3-core X 185 sq mm + 1-core X 150 sq mm
RM 2,494
Note:Item No 454-473 Rates include cost of PCC/steel poles their foundation, coping & earthing. Pole spacing is considered as 30 Meter and 50 Meter respectively for LT and HT
LT ABC ON EXISTING POLES
474 Supply and fix LT overhead lines on existing poles with XLPE insulated AB cable 3-core X 50 sq mm + 1 x 35 sq mm.
RM 224
475 do—but of size 3-core X 70 sq mm + 1-core X 50 sq mm
RM 321
476 do—but of size 3-core X 95 sq mm + 1-core X 70 sq mm
RM 424
477 do—but of size 3-core X 120 sq mm X 1-core X 70 sq mm
RM 489
478 do—but of size 3-core X 150 sq mm + 1-core X 95 sq mm
RM 572
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 36 of 117
Item No Description of Item Unit Rate
479 do—but of size 3-core X 185 sq mm + 1-core X 150 sq mm
RM 868
480 do—but of size 3-core X 240 sq mm + 1-core X 185 sq mm
RM 1,108
11 KV HT ABC ON EXISTING POLES
481 Supply and fix HT overhead lines on existing poles with XLPE insulated AB cable 3-core X 70 sq mm + 1 x 50 sq mm.
RM 693
482 do—but of size 3-core X 95 sq mm + 1 X 70 sq mm
RM 844
483 do—but of size 3-core X 185 sq mm + 1-core X 150 sq mm
RM 1,332
LT OVER HEAD LINE ON PCC POLE WITH ACSR CONDUCTOR
484
Supply and fix LT OH lines on 9 meter PCC poles with Continuous GI earth wire incl earthing of poles, cross arms, insulators etc and ACSR conductors of size 2 of 6/1 x 2.11 mm (Squirrel).
RM 422
485 do-- but of size 2 of 6/1 x 2.59 mm (Weasel) RM 472
486 do-- but of size 4 of 6/1 x 2.11 mm (Squirrel) RM 492
487 do-- but of size 3 of 6/1 x 2.59 mm (Weasel), 1 of 6/1 x 2.11mm (Squirrel)
RM 519
488 do-- but of size 3 of 6/1 x 3.00 mm (Ferret),1 of 6/1 x 2.59 mm (Weasel)
RM 557
489 do-- but of size 3 of 6/1 x 3.50 mm (Rabbit),1 of 6/1 x 2.59 mm (Weasel)
RM 586
490 do-- but of size 3 of 6/1 x 3.66 mm (Mink),1 of 6/1 x 2.59 mm (Weasel)
RM 623
491 do-- but of size 3 of 6/1 x 3.99 mm (Beaver), 1 of 6/1 x 3.00mm (Ferret)
RM 663
492 do-- but of size 3 of 6/1 x 4.22 mm (Otter),1 of 6/1 x 3.99 mm (Beaver)
RM 718
493 do-- but of size 3 of 6/1 x 4.50 mm (Cat), 1 of 6/1 x 3.99 mm (Beaver)
RM 750
494 do-- but of size 3 of 6/5.28 +7/1.76mm(Leopard), 1 of 6/1 x 3.99 mm (Beaver)
RM 824
495 do-- but of size 3 of 26/2.54 +7/1.90mm(Coyota),1 of 6/1 x 3.99 mm (Beaver)
RM 843
496 do-- but of size 3 of 30/7x3.00 mm (Panther),1 of 6/1 x 4.72 mm (Dog)
RM 1,151
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 37 of 117
Item No Description of Item Unit Rate
NOTE : Item No 484-496 Rates are including cost of PCC poles their foundation and coping. Spacing considered as 30 Meter
LT OVER HEAD LINE ON STEEL TUBULAR POLE WITH ACSR CONDUCTOR
497
Supply and fix LT OH lines on 9 meter Steel poles with Continuous GI earth wire incl earthing of poles cross arms, insulators etc poles and ACSR conductors of size 2 of 6/1 x 2.11 mm (Squirrel).
RM 744
498 do-- but of size 2 of 6/1 x 2.59 mm (Weasel) RM 795
499 do-- but of size 4 of 6/1 x 2.11 mm (Squirrel) RM 816
500 do-- but of size 3 of 6/1 x 2.59 mm (Weasel),1 of 6/1 x 2.11mm (Squirrel)
RM 843
501 do-- but of size 3 of 6/1 x 3.00 mm (Ferret),1 of 6/1 x 2.59 mm (Weasel)
RM 880
502 do-- but of size 3 of 6/1 x 3.50 mm (Rabbit), 1 of 6/1 x 2.59 mm (Weasel)
RM 908
503 do-- but of size 3 of 6/1 x 3.66 mm (Mink), 1 of 6/1 x 2.59 mm (Weasel)
RM 945
504 do-- but of size 3 of 6/1 x 3.99 mm (Beaver),1 of 6/1 x 3.00mm (Ferret)
RM 987
505 do-- but of size 3 of 6/1 x 4.22 mm (Otter),1 of 6/1 x 3.99 mm (Beaver)
RM 1,041
506 do-- but of size 3 of 6/1 x 4.50 mm (cat) ,1 of 6/1 x 3.99 mm (Beaver)
RM 1,073
507 do-- but of size 3 of 6/5.28 +7/1.76mm(Leopard),1 of 6/1 x 3.99 mm (Beaver)
RM 1,146
508 do-- but of size 3 of 26/2.54 +7/1.90mm(Coyota),1of 6/1 x 3.99 mm (Beaver)
RM 1,165
509 do-- but of size 3 of 30/7x3.00 mm (Panther),1 of 6/1 x 4.72 mm (Dog)
RM 1,473
NOTE :Item No 497-509 Rates are including cost of steel poles, their foundation and coping. Spacing considered as 30 Meter
LT OVER HEAD LINES ON EXISTING POLES
510 Supply and fix LT OH lines on existing poles with ACSR conductors size 2 of 6/1x2.11mm(Squirrel).
RM 67
511 do -- but of size 2 of 6/1 x 2.59 mm (Weasel)
RM 84
512 do-- but of size 4 of 6/1 x 2.11 mm (Squirrel)
RM 105
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 38 of 117
Item No Description of Item Unit Rate
513 do-- but of size 3 of 6/1 x 2.59 mm (Weasel),1 of 6/1 x 2.11mm (Squirrel)
RM 132
514 do-- but of size 3 of 6/1 x 3.00 mm (Ferret),1 of 6/1 x 2.59 mm (Weasel)
RM 170
515 do-- but of size 3 of 6/1 x 3.50 mm (Rabbit),1 of 6/1 x 2.59 mm (Weasel)
RM 198
516 do-- but of size 3 of 6/1 x 3.66 mm (Mink),1 of 6/1 x 2.59 mm (Weasel)
RM 234
517 do-- but of size 3 of 6/1 x 3.99 mm (Beaver),1 of 6/1 x 3.00mm (Ferret)
RM 276
518 do-- but of size 3 of 6/1 x 4.22 mm (Otter),1 of 6/1 x 3.99 mm (Beaver)
RM 331
519 do-- but of size 3 of 6/1 x 4.50 mm (cat) ,1 of 6/1 x 3.99 mm (Beaver)
RM 362
520 do-- but of size 3 of 6/5.28 +7/1.76mm(Leopard),1 of 6/1 x 3.99 mm (Beaver)
RM 435
521 do-- but of size 3 of 26/ 2.54 +7/1.91 mm(Coyota),1 of 6/1 x 3.99 mm (Beaver)
RM 454
HT OH LINES ON PCC POLE WITH ACSR CONDUCTOR
522
Supply and fix HT overhead line of 11KV on 11 meter PCC poles with continuous GI earth wire, including earthing of Poles cross arms, insulators etc and ACSR conductor of sizes 3 of 6/1 x 2.11 mm (Squirrel)
RM 395
523 do-- but size 3 of 6/1x2.59 mm (Weasel) RM 423
524 do-- but size 3 of 6/1x3.00 mm (Ferret) RM 450
525 do-- but size 3 of 6/1x3.50 mm (Rabbit) RM 479
526 do-- but size 3 of 6/1x3.66 mm (Mink) RM 514
527 do-- but size 3 of 6/1x3.99 mm (Beaver) RM 545
528 do-- but size 3 of 6/1x4.22 mm (Otter) RM 571
NOTE : Item No 522-528 Rates are including cost of PCC poles, their foundation and coping .Spacing considered as 50 Meter
HT OH LINES ON STEEL TUBULAR POLE WITH ACSR CONDUCTOR
529
Supply and fix HT overhead line of 11KV on 11 meter steel poles with continuous GI earth wire, including earthing of poles cross arms, insulators etc and ACSRconductor of sizes 3 of 6/1 x 2.11 mm (Squirrel)
RM 677
530 do-- but size 3 of 6/1x2.59 mm (Weasel) RM 703
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 39 of 117
Item No Description of Item Unit Rate
531 do-- but size 3 of 6/1x3.00 mm (Ferret) RM 732
532 do-- but size 3 of 6/1x3.50 mm (Rabbit) RM 760
533 do-- but size 3 of 6/1x3.66 mm (Mink) RM 795
534 do-- but size 3 of 6/1x3.99 mm (Beaver) RM 826
535 do-- but size 3 of 6/1x4.22 mm (Otter) RM 851
Note:Item No 529-535 Rates are including cost of steel poles their foundation and coping . Spacing between pole considered is 50 Meter.
HT OVER HEAD LINES ON EXISTING POLES
536 Supply and fix HT OH lines on Existing Poles with ACSR conductor of size3 of 6/1x2.11 mm (Squirrel)
RM 104
537 do-- but size 3 of 6/1x2.59 mm (Weasel) RM 132
538 do-- but size 3 of 6/1x3.00 mm (Ferret) RM 159
539 do-- but size 3 of 6/1x3.50 mm (Rabbit) RM 188
540 do-- but size 3 of 6/1x3.66 mm (Mink) RM 223
541 do-- but size 3 of 6/1x3.99 mm (Beaver) RM 253
542 do-- but size 3 of 6/1x4.22 mm (Otter) RM 279
4 POLE AND 2 POLE STRUCTURE WITH PCC POLE
543
Supply & erect 4 pole structure on 11 meter PCC Pole,anti-climbing device, PCC foundation & cross arms (Bracings) etc for one incoming and one out going.
Each 90,930
544
Supply & erect 4 pole structure on 11 meter PCC, with anti-climbing device, PCC foundation & cross arms etc for one incoming and two out going.
Each 1,03,001
545
Supply & erect 4 pole structure on 11 meter PCC Pole,anti-climbing device, PCC foundation & cross arms etc for one incoming and three out going.
Each 1,26,070
546 Supply and erect 2 pole structure on 11 meter PCC pole , anti-climbing device, PCC foundation & cross arms etc.
Each 45,548
4 POLE AND 2 POLE STRUCTURE WITH STEEL POLE
547
Supply & erect 4 pole structure on 11 meter steel tubular pole consisting of pole with anti-climbing device, PCC foundation & cross arms etc for one incoming and one out going.
Each 1,58,323
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 40 of 117
Item No Description of Item Unit Rate
548
Supply & erect 4 pole structure on 11 meter steel tubular pole consisting of pole with anti-climbing device, PCC foundation & cross arms etc for one incoming and two out going.
Each 1,70,392
549
Supply & erect 4 pole structure on 11 meter steel tubular pole consisting of pole with anti-climbing device, PCC foundation & cross arms etc for one incoming and three out going.
Each 1,93,462
550
Supply and erect 2 pole structure on 11 meter steel Tubular pole consisting of anti-climbing device, PCC foundation & cross arms etc.
Each 79,244
Note:Item No 543-550 Cost of 4 & 2 Pole structure only include cost of pole, foundation and steel bracings but does not include cost of Gang Operated device,earthing,LA etc.
LIGHTNING ARRESTORS
551 Supply and fix lightning arrestor HT 11 KV 10 KA station class
set of 3 45,675
552 Supply and fix lightning arrestor HT 33 KV 10 KA station class
set of 3 59,057
EARTHING
553
Earthing of machinery/equipment Installed at power house/substation, using 32 x 6 mm galvanized MS strip and MS galvanized plate of size 600 x 600 x 6 mm ,as earth electrode
Set of 2 earths
14,297
554
Earthing of machinery/equipment Installed at power house/substation, using 25 x 3 mm copper strip and copper plate of size 300 x 300 x 3 mm, as earth electrode.
Set of 2 earths
24,683
555
Earthing for poles & other machinery/equipment using 4 mm GI wire as earthing lead and MS galvanized plate of size 60 cm x 60 cm x 6 mm, as earth electrode.
Each 5,966
SERVICE CONNECTIONS
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 41 of 117
Item No Description of Item Unit Rate
556
Service connection with 6 sq mm twin core Weather proof aluminium conductor cable Suspended with No.8 SWG GI wire from Pole to service bracket & then to meter Including 40 mm GI pipe service bracket.
Each 2,146
557 -- do -- but with 10 sq mm twin core Weather Proof cable.
Each 2,369
METERS
558
Supply & fix Microprocessor based Single phase electronic temper proof energy meter of rating 10 to 60 Amp with optical communication port, conforming to IS: 13779.
Each 5,271
559
Supply & fix AC single phase static energy meter of accuracy class 1.0, 240 V, 50 Hz with Backlit LCD display of rating 5 - 30 A, (measures and displays KWH ,V, Current I, KW, pf last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power with transparent hinge type box.
Each 3,975
560
Supply & fix AC single phase static energy meter of accuracy class 1.0, 240 V 50 Hz with Backlit LCD display of rating 10 - 60 A (measures and displays KWH ,V, Current I, KW, pf last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power with transparent hinge type box.
Each 4,138
561
Supply & fix Single phase , two wire ,240 volt , 10- 60 A or less, accuracy class 1.0, IS Markied,single source pre payment meter including CIU & STTD
Each 8,520
562
Supply & fix AC Three phase static energy meter of accuracy class 1.0, 3 X 240 V ,50 Hz with Backlit LCD display of rating 5 - 20 A (suitable for measurement of KWH only)
Each 6,627
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 42 of 117
Item No Description of Item Unit Rate
563
Supply & fix AC Three phase static energy meter of accuracy class 1.0, 3 X 240 V, 50 Hz with Backlit LCD display of rating 10 - 60 A (suitable for measurement of KWH only)
Each 7,252
564
Supply & fix AC Three phase static energy meter of accuracy class 1.0 ,3 X 240 V ,50 Hz with Backlit LCD display of rating 10 - 60 A (measures and displays KWH ,V, Current I, KW, pf last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power with transparent hinge type box.
Each 12,268
565 Supply & fix Trivector meter three phase four wire ,3 x 240 volt , 10-60 Amp class 1.0 with box .
Each 13,183
566 Supply & fix Trivector meter three phase four wire TVM 110 Volt , 1 A/5A class 0.5 with box .
Each 31,440
567 Supply & fix Trivector meter three phase four wire TVM 110 Volt , 1 A/5A ,class 0.2 with box .
Each 63,823
568
Supply & fix Meter reading instruments with suitable software of capacity 16.5 MB to record, reading through optical communication port of any type of meter.
Each 1,26,819
569
Supply & fix Microprocessor based three phase electronic tamper proof energy meter of rating 10 to 60 Amp with optical communication port conforming to IS: 13779.
Each 10,373
570
Supply & fix Microprocessor based three phase electronic tamper proof, CT operated, energy meter for LT supply with optical communication port, accuracy class 0.5 voltage 3 x 240 V, 1/5 A conforming to IS: 13779.
Each 32,736
571
Supply & fix Microprocessor based three phase electronic tamper proof HT energy meter with optical communication port, accuracy class 0.5 rating 3 x 110 V, 1/5 A conforming to IS: 13779.
Each 39,219
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 43 of 117
Item No Description of Item Unit Rate
572 Supply & fix Digital panel meter for Amp, Volt,KWH, power factor and other parameter flush mounting of size 96 x96 mm
Each 23,605
573 Supply & fix Trivector meter base mounting of class 0.5
Each 40,677
FANS
574 Supply & fix fans ceiling complete with electronic type regulator and accessories 230 V,1200 mm sweep. BEE 5 star rated
Each 3,098
575 Supply & fix fans ceiling complete with electronic type regulator and accessories 230 V , 1400 mm sweep
Each 2,353
576 Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver
Each 2,847
577 -- do -- but size 380 mm sweep. Each 3,620
578 -- do -- but size 450 mm sweep. Each 4,888
579 -- do -- but size 600 mm sweep. Each 10,515
580 Supply & fix exhaust fans AC three phase 415 V of size 380 mm sweep with louver.
Each 4,410
581 .-- do -- but size 450 mm sweep. Each 6,086
582 . -- do -- but size 600 mm sweep. Each 10,444
583 Supply & fix fans table 230 volts single phase oscillating 400 mm sweep.
Each 2,010
584 Supply & fix Air Circulator fans 230 volts single phase oscillating 450 mm sweep suitable for wall mounting.
Each 8,225
585 . -- do – but for 600 mm sweep Each 10,416
586 . -- do – but for 750 mm sweep Each 9,800
TIME SWITCHES
587 Supply and fix time switches 250 V single Phase of 20 Amp rating with contactor fitted inside steel enclosure
Each 5,557
588 Supply and fix time switches 415 V three Phase of 20 Amp rating with contactor fitted inside steel enclosure
Each 8,136
589
Supply and fix time switches astro type (Having longitude and latitude of Indian cities in memory) 250 V single phase of 20 Amp rating with contactor fitted inside steel enclosure.
Each 11,132
LIGHTING
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 44 of 117
Item No Description of Item Unit Rate
STREET LIGHT/FLOOD LIGHT FITTINGS
590
Supply & fix street light fitting fluorescent lamp type complete with perplex cover, reflector, choke starter, bi-pin holders etc for 1 x 40 Watt fluorescent tube
Each 2,805
591 . -- do -- but for 2 x 40 Watt tubes Each 3,808
592 Supply and fix street light 1 x 28 Watt FTL (T5) IP 43
Each 2,846
593 . -- do -- but for 2 x 28 Watt FTL (T5) IP 43 Each 3,530
594 .--do-- but 1 x36 Watt FTL (T8) IP 43 Each 2,690
595 . -- do -- but for 2 x 36 Watt FTL (T8) IP 43 Each 3,513
596 Supply and fix street light 2 X 14 W (FTL T5) IP65
Each 4,484
597 Supply and fix street light 4 X 14 W (FTL T5) IP. 65
Each 8,561
598 Supply and fix street light 2 X 24 W (FTL T5) IP. 65
Each 4,661
599 Supply and fix street light 4 X 24 W (FTL T5) IP. 65
Each 8,924
600 Supply and fix CFL street light 1 X 36 W IP. 65
Each 2,457
601 Supply and fix CFL street light 2 X 36 W IP. 65
Each 3,804
602 Supply and fix CFL street light 3 X 36 W IP. 65
Each 8,050
603
Supply & fix street light fitting Mercury vapour lamp type complete with HPMV lamp, reflector, heat resistant glass bowl, choke etc complete in all respect for 80 Watt lamp.
Each 5,274
604 . -- do -- but for 125 Watt lamp Each 5,027
605 -- do -- but for 250 Watt lamp. Each 6,902
606 Supply & fix street light fitting HPSV lamp, ballast, igniter and other accessories for 70 Watt lamp.
Each 6,105
607 -- do -- but for 150 Watt lamp. Each 7,905
608 .-- do -- but for 250 Watt lamp Each 10,944
609 . -- do -- but for 400 Watt lamp. Each 19,483
610 Supply & fix Flood light fitting, complete with switch gear, control gear unit ,lamp and fixing for 400 Watt metal halide (MH)
Each 12,048
611 . -- do -- same as above but 250 Watt MH Each 10,843
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 45 of 117
Item No Description of Item Unit Rate
LED STREET LIGHTS (Clause of escalation not to applied for LED lights)
612 Supply and fix LED street light 10 W IP 65 Each 3,989
613 Supply and fix LED street light 35/36 W IP 65
Each 11,829
614 Supply and fix LED street light 70/75 W IP 65
Each 20,081
615 Supply and fix LED street light 100/105/110 W IP 65
Each 31,635
616 Supply and fix LED street light 115/120/125 W IP 65
Each 34,385
617 Supply and fix LED street light 135/140 W IP 65
Each 35,761
618 Supply and fix LED street light170 W IP 65 Each 48,139
619 Supply and fix LED street light 210 W IP 65 Each 52,266
LED FLOOD LIGHT
620 Supply and fix LED Flood light 35/36/37 W IP 65
Each 11,691
621 Supply and fix LED Flood light 70 W IP 65 Each 18,568
622 Supply and fix LED Flood light 105 W IP 65 Each 41,950
623 Supply and fix LED Flood light 120 W IP 65 Each 48,139
624 Supply and fix LED Flood light 140 W IP 65 Each 52,953
625 Supply and fix LED Flood light 210 W IP 65 Each 72,209
POST TOP LANTERNS
626 Supply and fix post top lantern light fitting for 70 Watt SV lamp complete With all accessories.
Each 6,707
627 . -- do-- but for 80 Watt MV lamp. Each 6,447
628 . -- do-- but for 125 Watt MV lamp. Each 6,381
INDUSTRIAL LIGHT FITTINGS
629
Supply & fix fluorescent light fitting complete with choke, condenser, starter, bi-pin lamp holders and Industrial reflector for 1 x 40 Watt tube.
Each 1,822
630 . -- do-- but for 2 x 40 Watt tubes Each 2,539
BULK HEAD FITTING
631 Supply & fix Bulkhead luminaire for CFL lamps 1x 9 Watt
Each 1,486
632 . -- do-- but for 1 x 13 Watt CFL Each 1,538
INDOOR LIGHT FITTINGS
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 46 of 117
Item No Description of Item Unit Rate
633
Supply & fix fluorescent light fitting Complete with chokes, condensers, starter,bi-pin holder, diffuser, polystyrene louvers 1 x 20 Watt .
Each 1,301
634 . -- do -- but for 1 x 40 Watt tube. Each 1,461
635
Supply &fix fluorescent light fitting complete with chokes, condensers, starters, bi-holders housed in stove enamelled rectangular box and fitting fitted with polystyrene louvers, end plates suitable for 2 x 20 Watt tube
Each 2,539
636 . -- do -- but for 2 x 40 Watt tube. Each 4,645
637 Supply & fix indoor decorative luminaire 1 X 28 W FTL (T5) IP 43
Each 1,635
638 Supply & fix indoor decorative luminaire 2 X 28 W FTL (T5) IP 43
Each 3,190
639 Supply & fix indoor decorative luminaire 1 X 36/40 W FTL (T8) IP 43
Each 1,822
640 Supply & fix indoor decorative luminaire 2 X 36 W FTL (T8) IP 43
Each 3,503
641 Supply & fix fluorescent light fitting slim channel with bi-directional reflector 1 X 28 W FTL (T5) IP 43
Each 2,165
642 Supply & fix fluorescent light fitting slim channel with bi-directional reflector 2 X 28 W FTL (T5) IP 43
Each 2,821
643 Supply & fix fluorescent light fitting slim channel with bi-directional reflector 1 X 36/40 W FTL (T8) IP 43
Each 2,343
644 Supply & fix fluorescent light fitting slim channel with bi-directional reflector 2 X 36 W FTL (T8) IP 43
Each 2,861
645 Supply and fix dust/corrosion proof 1 X 28 W FTL (T5) IP 65
Each 4,219
646 . -- do -- but for 2 x 28 Watt Each 5,609
647 . -- do -- but for 1 x 36 Watt FTL (T8) Each 4,397
648 . -- do -- but for 2 x 36 Watt FTL (T8) Each 5,556
LED INDOOR LIGHTS (Clause of escalation not to applied for LED lights)
649 Supply & fix LED tube light along with fixture,16 W
Each 1,376
650 Supply & fix LED tube light along with fixture,18W
Each 1,376
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 47 of 117
Item No Description of Item Unit Rate
651 Supply & fix LED tube light along with fixture, 20 W
Each 1,376
652 Supply & fix LED tube light along with fixture, 22 W
Each 1,857
653 Supply & fix LED down lighter, 3 W Each 1,307
654 Supply & fix LED down lighter, 6 W Each 1,789
655 Supply & fix LED down lighter, 9 W Each 2,132
656 Supply & fix LED down lighter, 10 W Each 5,640
657 Supply & fix LED down lighter, 12 W Each 6,052
658 Supply & fix LED down lighter ,6 W Each 6,877
659 Supply & fix LED down lighter, 20 W Each 7,565
660 Supply & fix LED down lighter 2'x2' , 35 W Each 8,941
661 Supply & fix LED down lighter 2'x2', 40 W Each 11,416
662 Supply & fix LED High bay , 72 W Each 24,758
663 Supply & fix LED High bay , 110 W Each 30,259
664 Supply & fix LED High bay , 140 W Each 36,449
665 Supply & fix LED bulk head ,10 W Each 2,476
666 Supply & fix LED tube light 20W water proof IP 65
Each 6,864
HIGH MAST LIGHT
667
Supply & installation of Galvanized steel high mast lighting system of 12.5 meter in two section, 3 mm section thickness, top dia 150 mm, bottom dia 340 mm, with 2/3 wire rope system and its accessories. System is suitable for loading 04 nos 50 to 100w LED Lights
Each 5,42,684
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 48 of 117
Item No Description of Item Unit Rate
668
Supply & installation of Galvanized steel high mast lighting system of 16 meter in two section, 3 mm section thickness, top dia 150 mm, bottom dia 340 mm, with 2/3 wire rope system and its accessories. System is suitable for loading 08 nos 80 to 150w LED lights
Each 7,59,605
669
Galvanized steel high mast lighting system of 20 meter in two section, 3 mm section thickness, top dia 150 mm, bottom dia 340 mm, with 2/3 wire rope system and its accessories. System is suitable for loading 06 nos 200 to 300w LED lights
Each 15,70,981
Note: In HM light, cost of luminaires is to be added separately. Rates are inclusive of cost of foundation
SHADOWLESS LIGHT FITTINGS
670
Supply and fix Shadow less light fitting complete with emergency power unit & battery back up for min 30 minutes (3 KVA), having dome of 810 mm dia, fully counter balanced moveable on ceiling trolley having a minimum longitudinal travel of 1350 mm and axial rotation of 360 deg. The unit to be suitable for operation on 230 V, single phase 50 cycles mains supply. (For Major OT having lux level> 120,000)
Each 4,98,031
671 -- do -- but for standard model suitable Having battery back up of 1 KVA and lux level >70,000
Each 3,64,709
672
Supply and fix Shadow less light fitting complete with emergency power unit & battery back up for min 30 minutes (3 KVA), having dome of 810 mm dia, fully counter balanced and fixed on suspension rod, capable of having axial rotation of 360 deg. The unit to be suitable for minor OT and Capable for operation on 230 V single phase, 50 cycles mains supply having lux level > 70,000.
Each 3,64,709
673 -- do -- but for mobile shadowless light fitting
Each 3,19,864
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 49 of 117
Item No Description of Item Unit Rate
FLAME PROOF WEATHER PROOF LIGHT FITTINGS
674 Supply and fix Flame proof weather proof fluorescent fixture 1 x 40 W x 4'
Each 19,421
675 Supply and fix Flame proof weather proof fluorescent fixture 2 x 40 W x 4'
Each 37,482
676 Supply and fix Flame proof bulk head fitting 200 W GLS/80 W HPMV/ 125 HPMV
Each 9,135
677 Supply and fix Flame proof bulk head fitting 2 x 26 W CFL
Each 10,202
678 Supply and fix Flame proof bulk head fitting 3 x 26 W CFL
Each 11,151
679 Supply and fix Flame proof - weather proof fitting suitable for 200 W GLS/ 80 W HPMV/125 W HPMV
Each 11,910
680 Supply and fix Flame proof - weather proof flood light fitting suitable for 300 W GLS/ 250 W HPMV/ 150 W metal halide
Each 25,398
681 Supply and fix Flame proof - weather proof flood light fitting suitable for 500 W GLS/ 400 W HPMV/ 400 W metal halide
Each 34,924
682 Supply and fix Flame proof - weather proof switch socket & plug combined 16 A,250 V(2P+Earth)
Each 11,507
683 Supply and fix Flame proof - weather proof switch socket & plug combined 16 A, 500 V(3P+Earth)
Each 12,653
684 Supply and fix Flame proof - weather proof switch socket & plug combined 25 A, 250 V(2P+Earth)
Each 12,795
685 Supply and fix Flame proof - weather proof switch socket & plug combined 25 A, 500 V(3P+Earth)
Each 13,887
686 Supply and fix Flame proof - weather proof MCB socket & plug combined 16 A, 250 V(2P+Earth)
Each 27,398
687 Supply and fix Flame proof - weather proof MCB socket & plug combined 16 A, 500 V(3P+Earth)
Each 28,547
688 Supply and fix FLP/WP switch/Isolator 10 Amp single pole ON/OFF
Each 2,201
689 Supply and fix FLP/WP switch/Isolator 10 Amp double Pole ON/OFF
Each 2,447
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 50 of 117
Item No Description of Item Unit Rate
690 Supply and fix FLP/WP switch/Isolator 16 Amp single Pole ON/OFF
Each 2,391
691 Supply and fix FLP/WP switch/Isolator 16 Amp double Pole ON/OFF
Each 2,613
DUST PROOF / DUST TIGHT /TOTALLY ENCLOSED TYPE TUBE LIGHT FITTING AND ACCESSORIES
692 Supply and fix Fluorescent tube light 1 x 40 Watt
Each 2,591
693 Supply and fix Fluorescent tube light 2 x 40 Watt
Each 3,307
694 Supply and fix Junction box dia 100 x 65 H Each 789
695 Supply and fix Junction box dia 120 x 70H Each 880
696 Supply and fix Junction box dia 130 x 70H Each 1,678
PRESTRESSED CEMENT CONCRETE POLES
697
Supply and fix Prestressed concrete poles of 9 meter long having 152 mm x 152 mm at top and 152 mm x 260 mm at bottom, including foundation and coping.
Each 7,754
698
Supply and fix Prestressed concrete poles of 11 meter long having 102 mm x 172 mm at top and 102 mm x 289 mm at bottom ,including foundation and coping.
Each 10,147
STEEL TUBULAR POLES
699
Supply and fix steel tubular swaged poles type 410 SP-22 (8.5 meter long) complete with CI base plate and finial including foundation and coping
Each 17,470
700 -- do -- but type 410 SP-31 (9.0 meter long)
Each 19,153
701 -- do -- but type 410 SP-37 (9.5 meter long)
Each 17,855
702 -- do -- but type 410 SP-44 (10.0 meter long)
Each 19,240
703 -- do -- but type 410 SP-55 (11.0 meter long)
Each 24,187
704 -- do -- but type 410 SP-55 (12.0 meter long)
Each 29,180
SWAN NECK TYPE (Single and double )
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 51 of 117
Item No Description of Item Unit Rate
705
Supply and fix steel tubular swaged poles type 410SP-31(9.0 meter long) Swan Neck Type complete with CI base plate and finial and single swan neck, Including foundation and coping .
Each 17,850
706 --do-- but type 410 SP-44 (10.0 meter long) Each 19,852
707 --do-- but type 410 SP-44 (11.0 meter long) Each 22,806
708
Supply and fix steel tubular swaged poles Type 410SP-31(9.0 meter long) Swan Neck Type complete with CI base plate and finial and double swan neck, Including foundation and coping.
Each 19,199
709 --do-- but type 410 SP-44 (10.0 meter long) Each 21,305
710 --do-- but type 410 SP-44 (11.0 meter long) Each 25,921
CRANES
711 Supply and fix Crane electrically operated OH complete with span 9 to 11 meter, lift 4.5 to 6 meter and of capacity 2 tons.
Each 14,65,330
712 .-do- but of 3 ton capacity Each 16,46,566
713 .do- but of 5 ton capacity Each 21,25,734
714 .-do- but of 10 ton capacity Each 32,16,638
715 .-do- but of 20 ton capacity Each 48,23,634
716 Supply and fix Crane electrically operated OH complete with span 12 to 16 meter, lift 4.5 to 6 meter and of capacity 2 tons.
Each 17,18,404
717 .-do- but of 3 ton capacity Each 19,41,959
718 .-do- but of 5 ton capacity Each 24,78,471
719 .-do- but of 10 ton capacity Each 38,77,359
720 .-do- but of 20 ton capacity Each 55,91,213
721 Supply and fix crane hand operated OH complete with span 9 to 11 meter, lift 4.5 to 6 meter and of capacity 1 tons.
Each 7,73,398
722 .-do- but of 2 ton capacity Each 9,00,253
723 .-do- but of 3 ton capacity Each 10,71,543
724 .-do- but of 5 ton capacity Each 12,27,280
725 .-do- but of 10 ton capacity Each 17,24,646
726 Supply and fix crane hand operated OH complete with span 12 to 16 meter, lift 4.5 to 6 meter of capacity 1 tons
Each 9,75,265
727 .-do- but of 2 ton capacity Each 11,21,480
728 .-do- but of 3 ton capacity Each 13,54,981
729 .-do- but of 5 ton capacity Each 16,75,872
730 .-do- but of 10 ton capacity Each 20,51,674
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 52 of 117
Item No Description of Item Unit Rate
CRANE FLAME PROOF
731 Supply and fix flame proof crane electrically operated OH complete with span 17 to 24 meter and of capacity 5 tons
Each 35,09,723
732 -do- but of 10 ton capacity Each 43,91,273
733 -do- but of 15 ton capacity Each 53,14,017
734 -do- but of 20 ton capacity Each 60,30,791
735 Supply and fix flame proof crane electrically operated OH complete with span 25 to 30 meter and of capacity 5 tons
Each 45,39,571
736 -do- but of 10 ton capacity Each 54,62,315
737 -do- but of 15 ton capacity Each 66,32,223
738 -do- but of 20ton capacity Each 73,90,191
LIFT
739
Supply and fix Lift electrically operated Microprocessor controlled complete with power driven automatic stainless steel (SS) sliding doors and having SS car enclosure, suitable to carry 8 passengers (544 Kg) at a speed of 1.0 M/sec to serve upto 6 floors (G+5floors).
Each 31,00,469
740 Extra cost for additional floor for 8 passengers
Each 1,71,185
741
Supply and fix Lift electrically operated Microprocessor controlled complete with power driven automatic stainless steel (SS) sliding doors and having SS car enclosure, suitable to carry 10 passengers (680 Kg) at a speed of 1.0 M/sec to serve upto 6 floors (G+5floors).
Each 33,08,790
742 Extra cost for additional floor for 10 passengers
Each 1,71,185
743
Supply and fix Lift electrically operated Microprocessor controlled complete with power driven automatic stainless steel (SS) sliding doors and having SS car enclosure, suitable to carry 13 passengers (884 Kg) at a speed of 1.5 M/sec to serve upto 6 floors (G+5floors).
Each 37,25,218
744 Extra cost for additional floor for 13 passengers
Each 1,85,045
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 53 of 117
Item No Description of Item Unit Rate
745
Supply and fix Lift electrically operated Microprocessor controlled complete with power driven automatic stainless steel (SS) sliding doors and having SS car enclosure, suitable to carry 16 passengers (1088 Kg) at a speed of 1.5 M/sec to serve upto 6 floors (G+5floors).
Each 42,62,153
746 Extra cost for additional floor for 16 passengers
Each 1,85,891
747
Supply and fix Lift electrically operated Microprocessor controlled complete with power driven automatic stainless steel (SS) sliding doors and having SS car enclosure, suitable to carry 20 passengers (1360 Kg) at a speed of 1.5 M/sec to serve upto 6 floors (G+5floors).
Each 49,63,184
748 Extra cost for additional floor for 20 passengers
Each 1,93,297
749 Automatic rescue device for lifts any capacity
Each 2,56,883
750
Supply and fix Lift electrically operated Microprocessor controlled complete with power driven automatic stainless steel (SS) sliding doors and having SS car enclosure of size 1000x2400 mm, suitable for Hospital stretcher , suitable to carry 15 passengers (1020 Kg) at a speed of 0.5 M/sec to serve upto 6 floors (G+5floors) including automatic rescue device.
Each 41,64,923
751 Extra cost for additional floor for hospital lifts Each 1,85,045
752
Supply and fix Lift electrically operated Microprocessor controlled complete with power driven automatic stainless steel (SS) sliding doors and having SS car enclosure of size 1000x2400 mm, suitable for Hospital stretcher , suitable to carry 20 passengers (1360 Kg) at a speed of 0.5 M/sec to serve upto 6 floors (G+5floors) including automatic rescue device.
Each 47,43,438
753 Extra cost for additional floor for hospital lifts Each 1,93,297
LIGHTNING PROTECTION
754 Supply & fix single pointed air termination aluminium rod 12mm dia, 300 mm dong
Each 408
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 54 of 117
Item No Description of Item Unit Rate
755 Supply & fix aluminium strip 25mm x 3mm complete with saddles and fixing screws for fitting the strip.
RM 204
756 Supply & fix copper strip 32mm x 6 mm buried in ground
RM 1,041
757 Supply and fix G strip 32mm x 6mm buried in ground
RM 294
EXCAVATION BY TRENCHLESS TECH
758
Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure.
RM 2,991
SOLAR PV GENERATION
759 Grid connected ground top Solar PV generation without battery MW 7,04,72,322
Components Module cost Degradation Civil and general wks Mounting structure Power Conditioning unit Cables and transformers Prelim & Op. Expenses Total
Cost(Lakh) Rs 365.80 Rs 11.29 Rs 60.00 Rs 50.00 Rs 50.00 Rs 60.00 Rs 69.00 Rs 666.09
Note: The rates for SPV generation are taken from CENTRAL ELECTRCITY
REGULATORY COMMISSION for the FY 2014-15 and service tax added. No escalation will be applied on these rates, however, these rates will stand updated as and when revised orders are issued by CERC.
760 Add 10% for single axis tracking
761 Add 20% for dual axis tracking
Ser No 762 - 1000 blank
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 55 of 117
SECTION – 2 EXTERNAL WATER SUPPLY
(Item No. 1001 TO 1472)
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 56 of 117
Item No Description of Item Unit Rate
SECTION - 2 EXTERNAL WATER SUPPLY
(Item No. 1001 TO 1472)
TUBE WELLS For bore well having casing pipe for pump as 350 mm dia and other as 250
mm dia
1001 Fixing cost for MS reducer, bail plug, well cap, MS strip for centering, MS iron clamps, electric logging and sample strata box.
Job 67,596
1002 Trial bore of 250 mm dia upto 200meter depth below ground level in any kind of soil strata including hard stone/boulder etc.
RM 1,820
1003
Trial bore of 250 mm dia exceeding 200meter depth below ground level and upto 400 RM in any kind of soil strata including hard stone/boulder etc.
RM 2,384
1004 Development of trial bore by reaming in following step:-
(a) From 250mm to 350 mm
(b) From 350mm to 450 mm
(c) From 450mm to 550 mm
(d) From 550mm to 650 mm
(a) Reaming up to 675 mm for 60 RM from ground level including casing pipe of 350mm dia and thickness 8mm and pea gravel.
RM 11,396
(b)
Reaming up to 525 mm from depth exceeding 60 meter to 200 meter including casing pipe of 250mm dia and thickness 8mm and pea gravel.
RM 6,861
(c)
Reaming up to 525 mm from depth exceeding to 200 meter to 300 meter including casing pipe of 250mm dia and thickness 8mm and pea gravel.
RM 8,522
(d)
Reaming up to 525 mm from depth exceeding to 300 meter to 400 meter including casing pipe of 250mm dia and thickness 8mm and pea gravel.
RM 9,822
1005 Additional cost for slotted pipe of 250 mm dia in lieu of casing pipe of 250 mm dia.
RM 2,311
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 57 of 117
Item No Description of Item Unit Rate
1006 Development of tube well with compressed air and after with 25% extra capacity pump by pumping muddy water.
Per Hr 3,250
1007 Yield test for the bore well by continuously pumping for 16 hours to determine safe pumping yield.
Each job
51,997
For bore well having casing pipe for pump as 200 mm dia
1008 Fixing cost for MS reducer, bail plug, well cap, MS strip for centering, MS iron clamps, electric logging and sample strata box.
Job 61,241
1009
Trial bore of 200 mm dia upto 200meter depth below ground level in any kind of soil strata including hard stone/boulder including electric logging, MS cap, MS flat iron clamps, reducing socket etc.
RM 1,618
1010
Trial bore of 200 mm dia exceeding 200meter depth below ground level and upto 400 RM in any kind of soil strata including hard stone/boulder etc.
RM 2,095
1011 Development of trial bore by reaming in following step:-
(a) From 200mm to 350 mm
(b) From 350mm to 450 mm
(c) From 450mm to 550 mm
(a) Reaming up to 525 mm for 60 RM from ground level including casing pipe of 200mm dia and thickness 8mm and pea gravel.
RM 11,266
(b)
Reaming up to 525 mm from depth exceeding 60 metre to 200 meter including casing pipe of 200mm dia and thickness 8mm and pea gravel.
RM 6,861
(c)
Reaming up to 525 mm from depth exceeding to 200 meter to 300 meter including casing pipe of 200mm dia and thickness 8mm and pea gravel.
RM 8,522
(d)
Reaming up to 525 mm from depth exceeding to 300 meter to 400 meter including casing pipe of 200mm dia and thickness 8mm and pea gravel.
RM 9,822
1012 Additional cost for slotted pipe of 200 mm dia in lieu of casing pipe of 200 mm dia.
RM 2,095
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 58 of 117
Item No Description of Item Unit Rate
1013 Development of tube well with compressed air and after with 25% extra capacity pump by pumping muddy water.
Per Hr 3,250
1014 Yield test for the bore well by continuously pumping for 16 hours to determine safe pumping yield.
Each job
51,997
PUMPSET/ STARTER
Supply and Fix Star delta Starter fully automatic suitable for 415 V AC
1015 For 12.5 HP Motor Each 9,719
1016 For 15.0 HP Motor Each 9,745
1017 For 25.0 HP Motor Each 13,051
1018 For 30.0 HP Motor Each 17,162
1019 For 35.0 HP Motor Each 22,737
1020 For 50.0 HP Motor Each 32,778
1021 For 75.0 HP Motor Each 57,168
1022 For 90 HP Motor Each 73,620
1023 For 125.0 HP Motor Each 85,464
1024 For 250.0 HP Motor Each 1,51,230
1025 For 400.0 HP Motor Each 1,81,746
Supply and Fix Submersible Pump Starter
1026 For 6.0 HP Motor Each 10,461
1027 For 10.0 HP Motor Each 11,686
1028 For 15.0 HP Motor Each 13,715
1029 For 20.0 HP Motor Each 17,002
1030 For 30.0 HP Motor Each 27,047
1031 For 50.0 HP Motor Each 38,617
Supply and Fix DOL Starter
1032 For 2 HP Each 3,020
1033 For 7.5 HP Each 3,392
1034 For 10.0 HP Each 4,197
1035 For 15.0 HP Each 4,784
1036 For 20.0 HP Each 7,492
Supply and Fix MONOBLOCK PUMP SET
1037 Monoblock pump set suitable for 415 V ,3 phase system having capacity 5 HP.
Each 42,404
1038 Monoblock pump set suitable for 415 V, 3 phase of capacity 10 HP.
Each 63,352
1039 Monoblock pump set suitable for 415 V, 3 phase system having capacity 12.5 HP.
Each 70,289
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 59 of 117
Item No Description of Item Unit Rate
1040 Monoblock pump set suitable for 415 V, 3 phase system having capacity 15 HP.
Each 74,378
CENTRIFUGAL PUMP SET
1041 Pumping sets, centrifugal, electric driven, supply and Install complete up to 5 WHP inclusive of starter and PCC foundation.
WHP 17,706
1042 - do - but above 5 WHP upto 10 WHP WHP 15,010
1043 - do - but above 10 WHP upto 15 WHP WHP 14,621
1044 - do - but above 15 WHP upto 20 WHP WHP 13,399
1045 - do - but above 20 WHP upto 30 WHP WHP 11,903
1046 - do - but above 30 WHP upto 35 WHP WHP 11,481
IC ENGINE DRIVEN PUMPS
1047 Pumping sets, centrifugal, IC engine driven, supply and Install complete up to 5 WHP inclusive of starter and PCC foundation.
WHP 54,329
1048 - do - but above 5 WHP upto 10 WHP WHP 32,291
1049 - do - but above 10 WHP upto 15 WHP WHP 18,918
1050 - do - but above 15 WHP upto 20 WHP WHP 16,978
1051 - do - but above 20 WHP upto 30 WHP WHP 14,047
Note :Item No 1037 -1046 Includes cost of automatic starter for pump above 10 WHP. For pump upto 10 WHP, cost of DOL starter has been included.
SUBMERSIBLE PUMPS
1052
Submersible pump, electric driven 415 V, TP suitable for 200/250 mm dia bore well ( Casing pipe size 200/250 mm) supply and Install complete upto 5 WHP inclusive of 40 metre long submersible cable and starter.
WHP 15,874
1053 - do - but above 5 WHP upto 10 WHP WHP 12,328
1054 - do - but above 10 WHP upto 15 WHP WHP 9,264
1055 - do - but above 15 WHP upto 20 WHP WHP 8,607
1056 - do - but above 20 WHP upto 25 WHP WHP 8,432
1057 - do - but above 25 WHP WHP 7,285
1058
Submersible pump, electric driven 415 V, TP suitable for 250 mm dia bore well ( Casing pipe size 300/350 mm) supply and Install complete upto 10 WHP inclusive of 40 metre long submersible cable and starter.
WHP 10,947
1059 - do - but above 10 WHP upto 15 WHP WHP 8,967
1060 - do - but above 15 WHP upto 25 WHP WHP 8,294
1061 - do - but above 25 WHP WHP 7,802
DISINFECTION,TREATMENT PLANTS
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 60 of 117
Item No Description of Item Unit Rate
1062
Supply and fix direct cylinder mounted type vacuum chlorinator for pressure feed including all gauges, pump, motor conforming to IS 10553 part - 2 having capacity 1.0 to 1000gm/hr.
Each 1,70,325
1063
Supply and fix direct cylinder mounted type vacuum chlorinator for gravity feed including all gauges, pump, motor conforming to IS 10553 part - 2 having capacity 1.0 to 1000gm/hr.
Each 1,56,153
1064
Supply and fix pressure feed gaseous chlorinator conforming to IS 10553 Part - 4 with pump, motor, gauges having capacity 1 to 1000gm/hr.
Each 1,59,696
1065
Supply and fix gravity feed gaseous chlorinator conforming to IS 10553 Part-4 with pump, motor, gauges having capacity 1 to 1000 gm./hr.
Each 1,24,265
1066 Supply and fix bleaching dozer bucket type of capacity 105 Litres.
Each 39,373
1067 Supply and fix bleaching dozer bucket type of capacity 145 Litres.
Each 48,656
1068 Supply and fix bleaching dozer bucket type of capacity 217 Litres.
Each 27,894
1069
Supply and Installation of Iron remover plant complete with pressure filter, catalytic media, air compressor, back washing facility including RCC foundation of capacity 5000 gallon/hr.
Each 10,31,679
1070
Supply and Installation of Iron remover plant complete with pressure filter, catalytic media, air compressor, back washing facility including RCC foundation of capacity 8000 gallon/hr.
Each 12,93,866
1071
Supply and Installation of Iron remover plant complete with pressure filter, catalytic media, air compressor, back washing facility including RCC foundation of capacity 10000 gallon/hr.
Each 16,16,286
PIPES
CAST IRON PIPE CLASS 'B'
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 61 of 117
Item No Description of Item Unit Rate
1072 Supply and lay Pipe cast Iron, S/S including specials, Class"B", 80mm(3") dia
RM 2,184
1073 - do - but 100 mm (4") dia RM 2,733
1074 - do - but 150 mm (6") dia RM 3,661
1075 - do - but 200 mm (8") dia RM 5,102
1076 - do - but 250 mm (10") dia RM 6,491
1077 - do - but 300 mm (12") dia RM 8,551
1078 - do - but 350 mm (14") dia RM 10,914
1079 - do - but 400 mm (16") dia RM 12,987
1080 - do - but 450 mm (18") dia RM 17,276
1081 - do - but 500 mm (20") dia RM 21,298
1082 - do - but 600 mm (27") dia RM 28,240
1083 Supply and lay Pipe cast Iron both ends flanged and drilled, including specials ,Class "B" ,80 mm (3") dia.
RM 3,311
1084 - do - but 100 mm (4") dia RM 2,904
1085 - do - but 150 mm (6") dia RM 3,791
1086 - do - but 200 mm (8") dia RM 5,381
1087 - do - but 250 mm (10") dia RM 6,411
1088 - do - but 300 mm (12") dia RM 8,381
CAST IRON PIPE CLASS 'A'
1089 Supply and lay pipe cast Iron, S/S including specials, Class "A", 80 mm(3") dia.
RM 1,986
1090 - do - but 100 mm (4") dia RM 2,519
1091 - do - but 150 mm (6") dia RM 3,465
1092 - do - but 200 mm (8") dia RM 4,604
1093 - do - but 250 mm (10") dia RM 6,029
1094 - do - but 300 mm (12") dia RM 7,642
1095 - do - but 350 mm (14") dia RM 9,199
1096 - do - but 400 mm (16") dia RM 11,960
1097 - do - but 450 mm (18") dia RM 15,317
1098 - do - but 500 mm (20") dia RM 18,705
1099 - do - but 600 mm (27") dia RM 19,542
CAST IRON PIPE CLASS ‘LA’
1100 Supply and lay pipe cast Iron, S/S including specials, Class “LA”, 80 mm (3”)dia
RM 1,757
1101 - do - but 100 mm (4") dia RM 1,701
1102 - do - but 150 mm (6") dia RM 2,436
1103 - do - but 200 mm (8") dia RM 3,568
1104 - do - but 250 mm (10") dia RM 4,547
1105 - do - but 300 mm (12") dia RM 5,855
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 62 of 117
Item No Description of Item Unit Rate
1106 - do - but 350 mm (14") dia RM 7,240
1107 - do - but 400 mm (16") dia RM 9,327
1108 - do - but 450 mm (18") dia RM 11,257
1109 - do - but 500 mm (20") dia RM 13,851
1110 - do - but 600 mm (27") dia RM 16,912
DUCTILE IRON PIPE
CLASS K-9
1111 Supply and lay pipe ductile Iron , S/S including specials, Class “K-9” ,100 mm (4”) dia
RM 1,592
1112 - do - but 150 mm (6") dia RM 2,151
1113 - do - but 200 mm (8") dia RM 2,814
1114 - do - but 250 mm (10") dia RM 4,430
1115 - do - but 300 mm (12") dia RM 4,807
1116 - do - but 350 mm (14") dia RM 5,762
1117 - do - but 400 mm (16") dia RM 7,026
1118 - do - but 450 mm (18") dia RM 8,346
1119 - do - but 500 mm (20") dia RM 9,990
1120 - do - but 600 mm (27") dia RM 12,591
CLASS K – 7
1121 Supply and lay pipe ductile Iron , S/S including specials, Class “K-7” ,100 mm (4”) dia
RM 1,392
1122 - do - but 150 mm (6") dia RM 1,958
1123 - do - but 200 mm (8") dia RM 2,488
1124 - do - but 250 mm (10") dia RM 3,371
1125 - do - but 300 mm (12") dia RM 4,347
1126 - do - but 350 mm (14") dia RM 5,133
1127 - do - but 400 mm (16") dia RM 6,040
1128 - do - but 450 mm (18") dia RM 7,276
1129 - do - but 500 mm (20") dia RM 8,553
1130 - do - but 600 mm (27") dia RM 11,106
Note : Item No 1072 - 1130 Rate include cost of laying, excavation, jointing etc.
GI PIPES ‘ MEDIUM CLASS’
1131 Supply and lay pipe galvanized, “Medium class”, including fittings 15 mm (1/2”) dia.
RM 231
1132 -- do -- but 20 mm (3/4”) dia RM 263
1133 .-- do -- but 25 mm (1.0”) dia RM 300
1134 -- do -- but 40 mm (1.5”) dia RM 404
1135 -- do -- but 50 mm (2”) dia RM 505
1136 -- do -- but 63 mm (2½”) dia RM 726
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 63 of 117
Item No Description of Item Unit Rate
1137 -- do -- but 80 mm (3”) dia RM 815
1138 -- do -- but 100 mm (4”) dia RM 1,180
1139 -- do -- but 150 mm (6”) dia RM 2,384
1140 -- do -- but 200 mm (8”) dia RM 2,704
GI PIPES ‘ HEAVY CLASS’
1141 Supply and lay pipe galvanized, “Heavy class”, including fittings, 15 mm (1/2”) dia.
RM 289
1142 -- do -- but 20 mm (1½”) dia RM 341
1143 -- do -- but 25 mm (1”) dia RM 452
1144 . --do-- but 40 mm (1½”) dia RM 591
1145 -- do-- but 50 mm (2”) dia RM 781
1146 -- do-- but 63 mm (2½”) dia RM 1,050
1147 -- do-- but 80 mm (3”) dia RM 1,237
1148 -- do-- but 100 mm (4”) dia RM 1,739
1149 -- do-- but 150 mm (6”) dia RM 2,596
Note : Item No 1131 - 1149 Rate include cost of laying, excavation, jointing etc.
M S PIPE (ERW)
1150 Supply and fix Pipe ERW Steel including specials, nominal dia 150 mm as per IS 3589 (1981) thickness 4.8 mm
RM 1,918
1151 -- do -- but 200 mm dia RM 2,249
1152 -- do -- but 250 mm dia RM 2,770
1153 -- do -- but 300 mm dia RM 3,209
1154 Supply and lay Pipes ERW Steel including specials, nominal dia 150 mm, as per IS 3589 (1981) thickness 5.4 mm
RM 2,032
1155 -- do -- but 200 mm dia RM 2,350
1156 -- do -- but 250 mm dia RM 2,935
1157 -- do -- but 300 mm dia RM 3,410
1158 Supply and lay Pipes ERW Steel including specials, nominal dia 150 mm as per IS 3589 (1981) thickness 6.0 mm
RM 2,133
1159 -- do -- but 200 mm dia RM 3,816
1160 -- do -- but 250 mm dia RM 3,417
1161 -- do -- but 300 mm dia RM 3,960
Note :Item No 1150-1161 Cost of ERW pipe does not include cost of excavation
PVC ( UPVC) PIPE CONFORMING TO IS: 13592 FOR SOIL AND WASTE WATER DISCHARGE AND RAIN WATER SYSTEM
1162 Supply and lay Pipe PVC class “A” conforming to IS 13592 including special, OD 75 mm dia.
RM 192
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 64 of 117
Item No Description of Item Unit Rate
1163 - do - but 110 mm dia. RM 282
1164 -- do -- but 160 mm dia RM 787
1165 Supply and lay Pipe PVC class “B” including Special, OD 75 mm dia
RM 269
1166 - do - but 110 mm dia. RM 436
1167 -- do -- but 160 mm dia RM 874
Note :Item No 1162-1167 Cost of PVC does not include cost of excavation
PP-R PIPE
1168
Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked ,IS-15801, PP-R pipes SDR 11 (PN-10) and PP-R plain fittings in trenches/walls/cellings or laying in floors complete of size outer dia 25 mm including all fittings
RM 271
1169 - do - but outer dia 32 mm RM 334
1170 - do - but outer dia 40 mm RM 423
1171 - do - but outer dia 50 mm RM 561
1172 - do - but outer dia 63 mm RM 809
1173 - do - but outer dia 75 mm RM 1,089
1174 - do - but outer dia 90 mm RM 1,489
1175 - do - but outer dia 110 mm RM 2,056
1176 - do - but outer dia 160 mm RM 4,155
1177
Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,IS-15801, PP-R pipes SDR 7.4 (PN-16) and PP-R plain fittings in trenches/walls/cellings or laying in floors complete of size outer dia 16 mm ,including fittings
RM 173
1178 - do - but outer dia 20 mm RM 206
1179 - do - but outer dia 25 mm RM 265
1180 - do - but outer dia 32 mm RM 357
1181 - do - but outer dia 40 mm RM 520
1182 - do - but outer dia 50 mm RM 717
1183 - do - but outer dia 63 mm RM 1,092
1184 - do - but outer dia 75 mm RM 1,493
1185 - do - but outer dia 90 mm RM 2,073
1186 - do - but outer dia 110 mm RM 2,885
1187 - do - but outer dia 160 mm RM 5,763
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 65 of 117
Item No Description of Item Unit Rate
1188
Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked, IS-15801, PP-R pipes SDR 6 (PN-20) and PP-R plain fittings in trenches/walls/cellings or laying in floors complete of size outer dia 16 mm, including fittings
RM 217
1189 - do - but outer dia 20 mm RM 251
1190 - do - but outer dia 25 mm RM 318
1191 - do - but outer dia 32 mm RM 422
1192 - do - but outer dia 40 mm RM 625
1193 - do - but outer dia 50 mm RM 854
1194 - do - but outer dia 63 mm RM 1,240
1195 - do - but outer dia 75 mm RM 1,717
1196 - do - but outer dia 90 mm RM 2,412
1197 - do - but outer dia 110 mm RM 3,336
1198 - do - but outer dia 160 mm RM 6,755
1199
Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked, IS-15801, PP-R pipes SDR 13.5 (PN-8) and PP-R plain fittings in trenches/walls/cellings or laying in floors complete of size outer dia 90 mm ,including fittings
RM 1,326
1200 - do - but outer dia 110 mm RM 1,818
1201 - do - but outer dia 160 mm RM 3,538
1202
Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,IS-15801 ,PP-R pipes SDR 7.4 (PN-16) and PP-R plain plain and brass threaded fittings laid in concealed work complete of size outer dia 16 mm
RM 317
1203 - do - but outer dia 20 mm RM 346
1204 - do - but outer dia 25 mm RM 413
1205 - do - but outer dia 32 mm RM 529
1206
Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked, IS-15801, PP-R pipes SDR 6 (PN-20) and PP-R plain and brass threaded fittings laid in concealed work complete of size outer dia 16 mm, including fittings
RM 388
1207 - do - but outer dia 20 mm RM 423
1208 - do - but outer dia 25 mm RM 498
1209 - do - but outer dia 32 mm RM 638
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 66 of 117
Item No Description of Item Unit Rate
Note : PP-R pipe rate does not include the cost of excavation etc
PP-R GATE VALVE
1210 Supply and fix PPR Gate Valves (Brass Insert) of 20 mm bore.
Each 1,048
1211 - do - but outer dia 25 mm Each 1,177
1212 - do - but outer dia 32 mm Each 1,410
1213 - do - but outer dia 40 mm Each 1,930
1214 - do - but outer dia 50 mm Each 2,542
1215 - do - but outer dia 63 mm Each 2,947
1216 - do - but outer dia 75 mm Each 4,578
1217 - do - but outer dia 90 mm Each 6,654
1218 - do - but outer dia 110 mm Each 9,783
PP-R BALL VALVES
1219 Supply and fix PPR Ball Valves (Brass Insert) of 20 mm bore.
Each 678
1220 - do - but outer dia 25 mm Each 793
1221 - do - but outer dia 32 mm Each 1,006
1222 - do - but outer dia 40 mm Each 1,203
1223 - do - but outer dia 50 mm Each 1,728
1224 - do - but outer dia 63 mm Each 2,139
1225 - do - but outer dia 75 mm Each 2,412
1226 - do - but outer dia 90 mm Each 3,396
1227 - do - but outer dia 110 mm Each 3,672
VALVES
SLUICE VALVES CLASS PN 1.0
1228 Supply and fix Valves, Sluice, flanged of class 1.0 PN,50 mm (2”)dia
Each 7,164
1229 -- do -- but 65 mm (2½”) dia Each 7,777
1230 -- do -- but 80 mm (3”) dia Each 8,968
1231 -- do -- but 100 mm (4”) dia Each 11,671
1232 -- do -- but 150 mm (6”) dia Each 17,252
1233 -- do -- but 200 mm (8”) dia Each 29,304
1234 -- do -- but 250 mm 106”) dia Each 42,055
1235 -- do -- but 300 mm (12”) dia Each 52,854
1236 -- do -- but 350 mm (14”) dia Each 79,748
1237 -- do -- but 400 mm (16”) dia Each 99,572
1238 -- do -- but 450 mm (18”) dia Each 1,22,586
1239 -- do -- but 500 mm (20”) dia Each 1,66,470
1240 -- do -- but 600 mm (24”) dia Each 2,12,228
SLUICE VALVES CLASS PN 1.6
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 67 of 117
Item No Description of Item Unit Rate
1241 Supply and fix Valves, Sluice, flanged of class 1.6 PN ,50 mm (2”)dia.
Each 8,088
1242 -- do -- but 65 mm (2½”) dia Each 9,242
1243 -- do -- but 80 mm (3”) dia Each 10,629
1244 -- do -- but 100 mm (4”) dia Each 13,971
1245 -- do -- but 150 mm (6”) dia Each 20,622
1246 -- do -- but 200 mm (8”) dia Each 35,126
1247 -- do -- but 250 mm 106”) dia Each 50,508
1248 -- do -- but 300 mm (12”) dia Each 64,511
1249 -- do -- but 350 mm (14”) dia Each 95,271
1250 -- do -- but 400 mm (16”) dia Each 1,10,151
1251 -- do -- but 450 mm (18”) dia Each 1,28,745
1252 -- do -- but 500 mm (20”) dia Each 2,32,511
1253 -- do -- but 600 mm (24”) dia Each 2,92,838
REFLEX VALVES
1254 Supply and fix Valve, reflux, with by-pass Arrangement, 50 mm (2”) dia
Each 7,610
1255 -- do -- but 65 mm (2.5”) dia Each 8,330
1256 -- do -- but 80 mm (3”) dia Each 9,119
1257 -- do -- but 100 mm (4”) dia Each 11,501
1258 -- do -- but 150 mm (6”) dia Each 17,540
1259 -- do -- but 200 mm (8”) dia Each 28,309
1260 -- do -- but 250 mm (10”) dia Each 50,225
1261 -- do -- but 300 mm (12”) dia Each 60,233
1262 -- do -- but 350 mm (14”) dia Each 99,021
1263 -- do -- but 400 mm (16”) dia Each 1,23,589
1264 -- do -- but 450 mm (18”) dia Each 1,69,574
1265 -- do -- but 500 mm (20”) dia Each 2,69,559
1266 -- do -- but 600 mm (24”) dia Each 3,38,778
BUTTERFLY VALVES
1267 Supply and fix Valve, butterfly conforming to IS 13095,50 mm (2”) dia.
Each 4,490
1268 -- do -- but 65 mm (2.5”) dia Each 5,015
1269 -- do -- but 80 mm (3”) dia Each 5,621
1270 -- do -- but 100 mm (4”) dia Each 6,681
1271 -- do -- but 150 mm (6”) dia Each 9,894
1272 -- do -- but 200 mm (8”) dia Each 15,604
1273 -- do -- but 250 mm (10”) dia Each 24,049
1274 -- do -- but 300 mm (12”) dia Each 32,784
1275 -- do -- but 350 mm (14”) dia Each 47,763
1276 -- do -- but 400 mm (16”) dia Each 58,173
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 68 of 117
Item No Description of Item Unit Rate
1277 -- do -- but 450 mm (18”) dia Each 69,401
1278 -- do -- but 500 mm (20”) dia Each 1,07,846
1279 -- do -- but 600 mm (24”) dia Each 1,34,797
FOOT VALVES
1280 Supply and fix Foot Valve conforming to IS 4038, 50 mm (2”) dia.
Each 4,108
1281 -- do -- but 65 mm (2.5”) dia Each 4,728
1282 -- do -- but 80 mm (3”) dia Each 5,697
1283 -- do -- but 100 mm (4”) dia Each 7,548
1284 -- do -- but 150 mm (6”) dia Each 11,672
1285 -- do -- but 200 mm (8”) dia Each 22,087
1286 -- do -- but 250 mm (10”) dia Each 31,483
1287 -- do -- but 300 mm (12”) dia Each 42,288
1288 -- do -- but 350 mm (14”) dia Each 69,567
1289 -- do -- but 400 mm (16”) dia Each 88,413
STRAINER
1290 Supply and fix Strainer Y type conforming to IS, size50 mm (2”) dia.
Each 5,110
1291 -- do -- but 65 mm (2.5”) dia Each 7,043
1292 -- do -- but 80 mm (3”) dia Each 9,147
1293 -- do -- but 100 mm (4”) dia Each 12,654
1294 -- do -- but 150 mm (6”) dia Each 17,152
1295 -- do -- but 200 mm (8”) dia Each 29,465
1296 -- do -- but 250 mm (10”) dia Each 42,477
1297 -- do -- but 300 mm (12”) dia Each 63,513
1298 -- do -- but 350 mm (14”) dia Each 67,349
1299 -- do -- but 400 mm (16”) dia Each 84,094
AIR RELEASE VALVE
1300
Supply and fix Cast Iron Air Valves with single air Outlets, conforming to IS 14845 of size 50 mm dia bore and fixing up in Cast Iron Water supply mains of size 50 mm dia.
Each 8,505
1301 Cast Iron Air Valves with two air Outlets, 50 mm dia bore and fixing Up in cast iron water supply mains
Each 7,898
1302 -- do -- but 80 mm dia bore Each 9,487
1303 -- do -- but 100 mm dia bore Each 11,891
1304 -- do -- but 150 mm dia bore Each 25,941
1305 -- do -- but 200 mm dia bore Each 50,541
GLOBE VALVE
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 69 of 117
Item No Description of Item Unit Rate
1306 Supply and fix Valve, globe conforming to IS 9338,50mm (2”) dia pipe
Each 5,862
1307 -- do -- but 65 mm (2.5”) dia Each 8,716
1308 -- do -- but 80 mm (3”) dia Each 11,127
1309 -- do -- but 100 mm (4”) dia Each 18,780
1310 -- do -- but 150 mm (6”) dia Each 31,419
1311 -- do -- but 200 mm (8”) dia Each 55,309
1312 -- do -- but 250 mm (10”) dia Each 86,113
1313 -- do -- but 300 mm (12”) dia Each 1,14,761
STOP COCK, BIB COCK
1314 Supply and fix Valve, stop, screwed,15 mm (1/2”) dia pipe
Each 728
1315 -- do -- but 20 mm (3/4”) dia pipe Each 946
1316 -- do-- but 25 mm (1”) dia pipe Each 1,431
1317 -- do-- but 40 mm (1.5”) dia pipe Each 2,825
1318 -- do-- but 50 mm (2”) dia pipe Each 4,336
1319 Supply and fix Cock, bib, brass, screwed down For size 15 mm (1/2”) dia pipe
Each 450
1320 -- do-- but 20 mm (3/4”) dia pipe Each 466
1321 -- do-- but 25 mm (1”) dia pipe Each 517
1322 Supply and fix Cock, bib, brass chromium plated, screwed down For size 15 mm (1/2”) dia pipe
Each 896
1323 Supply and fix Cock, pillar, brass chromium plated, screwed down for size 15 mm (1/2”) dia pipe
Each 915
1324 Supply and fix Cock, stop, brass chromium plated, screwed down for size 15 mm (1/2”) dia pipe
Each 806
1325 Supply and fix Cock, bib, brass chromium plated, screwed down For size 20 mm (3/4”) dia pipe
Each 873
HOT WATER APPARATUS
1326 Supply and fix Water heater storage type, electric,capacity 25 litres.BEE 5 star rated
Each 15,003
1327 Supply and fix Water heater storage type, electric, capacity 35 litres
Each 15,456
1328 -- do-- but of capacity 50 litres Each 19,314
1329 -- do-- but of capacity 70 litres Each 27,603
1330 -- do-- but of capacity 100 litres Each 42,546
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 70 of 117
Item No Description of Item Unit Rate
1331
Supply and Installation of Solar water heating system ,Flat plate collector type ,with heat exchanger of 100 litre per day capacity ,with electrical heating back up
Each 48,552
1332
Supply and Installation of Solar water heating system ,Flat plate collector type ,with heat exchanger of 200 litre per day capacity ,with electrical heating back up
Each 88,887
1333
Supply and Installation of Solar water heating system ,Flat plate collector type ,with heat exchanger of 300 litre per day capacity ,with electrical heating back up
Each 1,39,120
1334
Supply and Installation of Solar water heating system ,Flat plate collector type ,with heat exchanger of 500 litre per day capacity ,with electrical heating back up
Each 2,14,748
1335
Supply and Installation of Solar water heating system ,Flat plate collector type ,with heat exchanger of 1000 litre per day capacity ,with electrical heating back up
Each 4,38,832
1336
Supply and Installation of Solar water heating system ,Flat plate collector type ,with heat exchanger of 1500 litre per day capacity ,with electrical heating back up
Each 6,46,111
1337
Supply and Installation of Solar water heating system ,Flat plate collector type ,with heat exchanger 2000 litre per day capacity ,with electrical heating back up
Each 8,53,389
Note: Item No 1331-1337 Solar water heater rates include the cost of civil wks,cold and hot water tanks,cold and hot water pipe lines,insulation,electical cabling etc.In case if the length of insulated hot water pipe is more than 1RM/10Ltr cap in that case cost for additional length of insulated pipe to be estimated and included.
FIRE FIGHTING
1338 Supply & fix fire hydrant landing valve type A (single head outlet) of 63 mm dia conforming to IS 5290
Each 12,077
1339 - do - but type B ( double head outlet) Each 23,563
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 71 of 117
Item No Description of Item Unit Rate
1340
Supply and fix hose box for keeping 2 Nos hose pipe of length 15 meter each, branch pipe.nozzle, coupling etc of MS sheet of Thickness 2.0 mm
Each 5,344
1341 Supply and fix 63 mm dia gun metal branch pipe with 12.5 mm nozzle conforming to IS 903
Each 4,306
1342
Supply and fix hose box for hose reel of 20 mm size of 30 meter length complete with coupling branch pipe and nozzle , MS sheet 2 mm thickness
Each 7,629
1343 Supply and fix hose reel of 20 mm dia and 30 meter length conforming to IS 5132
Each 15,717
1344 Supply and fix branch pipe with nozzle of 20 mm dia for hose reel conforming to IS 8090
Each 1,402
1345
Supply and fix 63 mm dia 15 meter long hose conforming to IS 636 complete with male and female coupling conforming to IS 903
Each 6,398
1346 Supply and fix fire hydrant stand post with provn of single outlet conforming to IS 908
Each 3,767
1347
Supply and fix electric motor siren conforming to IS 1941 suitable for three phase 415 V supply with motor not exceeding 3.75 KW power and able to deliver 143 DB noise level.
Each set
12,714
1348 Supply and Install Electric Driven Jockey pump delivering 180 LPM up to 70 Meter head
Each 2,38,796
1349 Supply and Install Electric Driven Jockey pump delivering 180 LPM above 70 meter head up to 90 meter head
Each 2,80,519
1350 Supply and Install Booster pump up to 30 meter head discharge 450 LPM
Each 1,21,092
1351 .--do-- but 900 LPM Each 1,22,484
1352 Supply and Install Booster pump 36 meter head discharge 450 LPM
Each 1,44,948
1353 Supply and Install Booster pump 36 meter head discharge 900 LPM
Each 1,44,948
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 72 of 117
Item No Description of Item Unit Rate
1354
Supply and Install Diesel Engine driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft, suitable for delivering 1620 LPM, 70 meter head ,1800RPM
Each 9,09,619
1355 .--do-- but 90 M head,but 2150RPM Each 8,10,687
1356
Supply and Install Diesel Engine driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft, suitable for delivering 2280 LPM, 70 meter head,1800RPM
Each 9,09,619
1357 .--do-- but 90 M head,1800RPM Each 9,09,619
1358
Supply and install Diesel Engine driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft,suitable for delivering 2640 LPM, 70 meter head,1800 RPM
Each 9,09,619
1359 .--do-- but 90 M head,1800 RPM Each 10,14,489
1360
Supply and Install Diesel Engine driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft suitable for delivering 2850 LPM, 70 meter head,1800 RPM
Each 9,09,619
1361 .--do-- but 90 M head Each 10,14,489
1362
Supply and Install Diesel Engine driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft, suitable for delivering 4560 LPM, 70 meter head,2300 RPM
Each 10,68,982
1363 .--do-- but 90 M head,2300 RPM Each 10,94,039
1364
Supply and Install Electric driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft, suitable for delivering 1620 LPM, 70 meter head,2900 RPM
Each 3,03,036
1365 .--do-- but 90 M head,2900 RPM Each 3,40,033
1366
Supply and Install Electric driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft, suitable for delivering 2280 LPM, 70 meter head,2900 RPM
Each 4,16,971
1367 .--do-- but 90 M head,2900 RPM Each 4,84,989
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 73 of 117
Item No Description of Item Unit Rate
1368
Supply and Install Electric driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft, suitable for delivering 2640 LPM, 70 meter head,2900 RPM
Each 4,16,971
1369 .--do-- but 90 M head,2900 RPM Each 4,84,989
1370
Supply and Install Electric driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft,suitable for delivering 2850 LPM, 70 meter head,2900 RPM
Each 4,16,971
1371 .--do-- but 90 M head,2900 RPM Each 4,84,989
1372
Supply and Install Electric driven fire pump horizontal end suction , centrifugal type,CI casing and bronze impeller stainless steel shaft, suitable for delivering 4560 LPM, 70 meter head ,1480 RPM
Each 11,44,172
1373 .--do-- but 90 M head, 2900 RPM Each 10,03,440
1374
Supply and fix MS flanged pipe 25mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer
RM 477
1375
Supply and fix MS flanged pipe 32mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer
RM 604
1376
Supply and fix MS flanged pipe 40mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer
RM 656
1377
Supply and fix MS flanged pipe 50mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer
RM 910
1378
Supply and fix MS flanged pipe 65mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer
RM 1,122
1379
Supply and fix MS flanged pipe 80mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer
RM 1,418
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 74 of 117
Item No Description of Item Unit Rate
1380
Supply and fix MS flanged pipe 100mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer
RM 2,032
1381
Supply and fix MS flanged pipe 150mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer
RM 2,855
1382
Supply and fix MS flanged pipe 200mm NB heavy duty for multi storied building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer
RM 3,343
1383 Supply and fix 80mm bore hand operated butterfly valve of pressure not less than 15 Kg / Sqcm with complete set
Each 6,370
1384 Supply and fix 100mm bore hand operated butterfly valve of pressure not less than 15 Kg / Sqcm with complete set
Each 8,295
1385 Supply and fix 150mm bore hand operated butterfly valve of pressure not less than 15 Kg / Sqcm with complete set
Each 11,109
1386 Supply and fix 200mm bore hand operated butterfly valve of pressure not less than 15 Kg / Sqcm with complete set
Each 20,907
1387 Supply and fix Dual plates CI wafer type check valve, 80 mm bore tested to pressure of 15Kg/ Sqcm complete set
Each 7,406
1388 Supply and fix Dual plates CI wafer type check valve, 150 mm bore tested to pressure of 15Kg/ Sqcm complete set
Each 13,331
1389 Supply and fix Pressure gauge 100 mm dia with ball valve of pressure 25 Kg/Sqcm
Each 1,334
1390
Supply and fix Gun metal fire brigade in let connection for connecting to external fire hydrant ring main consisting of two nos 63mm dia instantaneous type male coupling with built in check valves and 150mm dia, flanged outlet complete with all accessories.
Each 12,696
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 75 of 117
Item No Description of Item Unit Rate
1391
Supply and fix Gun metal fire brigade inlet connection (suction collecting head) consisting of four nos 63mm dia instantaneous type male coupling with built in check valves and 150mm dia sluice valve (one no 150mm dia NRV), and 150mm dia flanged outlet complete with all accessories.
Each 10,157
1392
Supply and fix MS cabinet (approx 750mm x 600mm x 450mm) to encl fire brigade inlet connections fabricated from 16 gauge sheet with full front glass door and locking arrangement painted and mounted on masonry platform complete
Each 12,696
1393
Supply and fix Air cushioning tank (Air vessel) 250mm dia x 1000mm high with dished top, made of minimum 6mm thick MS pipe /plate complete with 20mm dia. Brass air valve (ball type), 20mm dia stop valve, pressure gauge with brass stop cock, nipple tees elbows and all accessories complete
Each 13,585
1394 Supply and fix Automatic air release valve 50mm dia suitable for domestic water with 50mm gun metal stop valve complete
Each 12,696
1395
Supply and fix Mild Steel class 'C' diesel pump exhaust pipe 150mm dia with one layer of10mm thick asbestos rope insulation and including all fitting clamp/ structural steel supports complete
RM 2,286
1396 Supply and fix Bulb type gun metal sprinkler head pendent type set to operate at 68 degree C
Each 494
1397 .--do--upright type Each 456
1398 .--do--but side wall type Each 637
1399 .--do--but concealed type Each 1,899
1400 Supply and fix Bulb type gun metal sprinkler head, pendent type, set to operate at 79 degree C
Each 488
1401 .--do--upright type Each 488
1402 .--do--but side wall type Each 738
1403 .--do--but concealed type Each 2,255
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 76 of 117
Item No Description of Item Unit Rate
1404 Supply and fix Sprinkler quick/early response type , pendent type, set to operate at 68 degree C
Each 1,232
1405 .--do--upright type Each 1,292
1406 Supply and fix Sprinkler quick /early response type , pendent type, set to operate at 79 degree C
Each 1,232
1407 .--do--but concealed type Each 1,292
1408
Supply and fix Fire alarm control panel complying with BS EN 54 Single loop panel of capacity from 99 detectors & 99 modules upto 200 detector
Each set
1,31,346
1409 -ditto - but 2 loop panel with 99 detectors & 99 modules & upto 200 detectors and modules per loop
Each set
1,55,466
1410 -ditto - but 4 loop panel with 99 detectors & 99 modules & upto 200 detectors and modules per loop
Each set
2,82,319
1411 -ditto - but 5 loop panel with 99 detectors & 99 modules & upto 200 detectors and modules per loop
Each set
8,19,209
1412
Supply and fix Detectors Complying with and type certified to EN-45 Addressable type smoke detector Photoelectric / Optical with base with self built intelligence as per IS: 11360
Each 5,378
1413 ditto but Addressable type multisensor detector with heat and smoke combination
Each 6,129
1414 .--do-- but Addressable type heat detector with base with rate of rise cum fixed temperature as per IS: 2175
Each 5,378
1415 ditto but Addressable type duct detector housing with sampling tube add up cost of smoke detector
Each 13,046
1416
ditto but Addressable type Flame detectors with UV/IR detection Capacity (add up cost of module to be a complete set, the type of module shall be relay type module)
Each 1,53,565
BEAM MASTER DETECTOR
1417 Supply and fix Beam Master detector with Transmitter and receiver (Add power supply unit & module)
Each 99,165
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 77 of 117
Item No Description of Item Unit Rate
1418 Supply and fix Beam Master Detector, Transceiver Type (Add power supply unit & module)
Each 1,02,381
ANNUCIATING DEVICES
1419 Supply and install Addressable control module
Each 7,264
1420 Supply and fix Addressable monitor module Each 7,264
1421 Supply and fix Addressable manual call point resettable type
Each 6,835
1422 Supply and fix Addressable electronic sounder cum strobe
Each 9,301
1423 Supply and fix Addressable sounder Each 7,264
1424 Supply and fix Loop powered sounder strobe
Each 8,335
1425 Supply and fix Short circuit isolators Each 3,726
1426 Supply and fix Explosive proof manual call point (Add up control module)
Each 11,123
1427 Supply and fix Remote response indicators Each 199
1428 Supply and fix 6 Watt ceiling Speaker Each 1,573
1429 Supply and fix 4 Watt ceiling Speaker Each 1,545
PA SYSTEM
1430 Supply and fix 6 Watt wall mount CD Speaker
Each 3,039
1431 Supply and fix 10 Watt wall mount CD Speaker
Each 3,726
1432 Supply and fix 100 Watt amplifier Each 43,207
1433 Supply and fix 250 Watt Amplifier Each 66,381
1434 Supply and fix 500 Watt Amplifier Each 83,980
1435 Supply and fix Microphone set Each 7,505
1436 Supply and fix Control Console Each 50,395
1437
Supply and fix Fire Alarm sounders / Sirens electronic type horizontal single stage continuous normal operation for at least 50 minutes with sound level 65 DB to 120 DB measured at 1.5 meter with sound output variation of + 5 DB for 500 meter range
Each 11,249
1438 ditto but 1000 m range Each 11,416
1439 ditto but 1500 m range Each 16,346
1440 ditto but 2000 m range Each 17,244
1441 ditto but 3500 m range Each 20,886
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 78 of 117
Item No Description of Item Unit Rate
1442
Supply and fix Fire Alarm sounders / Sirens electronic type horizontal two stage continuous normal operation for at least 50 minutes with sound level 65 db to 120 db Measured at 1.5 m with sound output variation of + 5 db 500m range
Each 12,096
1443 ditto but 1000m range Each 14,420
1444 ditto but 1500m range Each 17,753
1445 ditto but 3500m range Each 21,601
1446 Supply and fix Addressable manual call point break glass type with alarm LED complete
Each 7,110
1447 Response indicator unit complete Each 124
SWIMMING POOL FILTRATION PLANT
1448
Supply and install filtration cum recycle plant for swimming pool of size 50 x 21 x 2.85 (Avg. depth) meter having total water capacity 30,00,000 Litre suitable for 6 hr. turn over period complete with following:—
Each 1,58,70,000
Filtration rate 500 M3/Hr
(a) Pressure filter suitable for flow rate of 125 M3/hr,pressure 2.5 Kg/cm2 ,4Nos
(b) Water circulating pump 5Nos(4 W + 1S)having discharge 125 M3/hr.
(c) Complete UPVC Pipe network, with in filtration plant and from plant to swimming pool basin, suitable for 10 Kg/cm2 pressure
(d) Valves, Valve battery its support, chemical dosing pumps, tank agitators
(e) Pool basin accessories, pool cleaning and maintenance equipment.
(f) Stainless steel Swimming pool Ladder , electric panel suitable for filtration plant etc
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 79 of 117
Item No Description of Item Unit Rate
(g) All E/M items except under water lighting
1449 Add 20% for under water light in 30,00,000 Litre capacity swimming pool
1450
Supply and install filtration cum recycle plant for swimming pool of size 25 x 13.5 x 2.35 (Avg. depth) meter having total water capacity 8,00,000 Litre suitable for 5-6 hr. turn over period complete with following:—
Each 52,90,000
(a) Pressure filter suitable for flow rate of 80M3/hr,pressure 2.5 Kg/cm2 ,2Nos
(b) Water circulating pump 3Nos(2W + 1S)having discharge 80 M3/hr.
(c) Complete UPVC Pipe network, with in filtration plant and from plant to swimming pool basin, suitable for 10 Kg/Cm2 pressure
(d) Valves, Valve battery its support, chemical dosing pumps, tank agitators
(e) Pool basin accessories,pool cleaning and maintenance equipment.
(f) Stainless steel Swimming pool Ladder , electric panel suitable for filtration plant etc
(g) All E/M items except under water lighting accounted
1451 Add 15 % for under water lighting for 8,00,000 Litre capacity swimming pool
Note : For Item No 1448 and 1451Cost of civil wks is extra
PRESSURE FILTER
1452 Supply and fix Pressure filter for flow rate of 22 M3/hr.
Each 6,94,244
1453 -- do – but flow rate 35 M3/hr. Each 8,33,371
1454 -- do – but flow rate 50 M3/hr. Each 9,59,977
1455 -- do – but flow rate 62 M3/hr. Each 10,99,104
1456 -- do – but flow rate 76 M3/hr. Each 12,38,231
1457 -- do – but flow rate 90 M3/hr. Each 12,38,231
1458 -- do – but flow rate 100 M3/hr. Each 13,77,358
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 80 of 117
Item No Description of Item Unit Rate
1459 -- do – but flow rate 125 M3/hr. Each 20,71,602
1460 -- do – but flow rate 150 M3/hr. Each 23,37,334
SWIMMING POOL WATER TREATMENT BASED ON CU++ AND AG++ ION BASED TECHNOLOGY
1461 Supply and fix Ionizer system for swimming pool capacity up to 3.0 lakh litre
Each 12,38,231
1462 .-- do – but for capacity 3.0 to 5.0 lakh litre Each 15,61,701
1463 .-- do – but for capacity 5.0 to 7.50 lakh litre Each 18,99,084
1464 .-- do – but for capacity 7.5 to 10.0 lakh litre Each 23,09,509
1465 .-- do – but for capacity 10.0 to 12.5lakh litre Each 26,99,064
1466 .-- do – but for capacity 12.5 to 15.0 lakh litre
Each 30,39,925
1467 .-- do – but for capacity 15.0 to 21.50 lakh litre
Each 38,39,906
1468 .-- do – but for capacity 24.0 to 32.0 lakh litre
Each 57,38,989
RO PLANT
1469 Supply and fix Reverse Osmosis Plant of out put capacity of 25 Litres per hour
Each 60,042
1470 Supply and fix Reverse Osmosis Plant of out put capacity of 60 Litres per hour
Each 1,85,605
1471 Supply and fix Reverse Osmosis Plant of out put capacity of 100 Litres per hour
Each 2,28,550
1472 Supply and fix Reverse Osmosis Plant of out put capacity of 150 Litres per hour
Each 2,90,343
NOTE: RO Rates include cost of civil wks,raw water/clear water storage tank,softener,plumbing and electrical wks. Feed water characterstics: Turbidity <5 ppm,Iron <0.3 ppm,ph range 6.5-7.2,total hardness <500ppm,TDS<1500 ppm
Ser No 1473-1500 Blank
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 81 of 117
SECTION-3
REFRIGERATION, AIR-CONDITIONING , REFRIGERATORS
&
CENTRAL HEATING SYSTEM
(ITEM NO 1501 to 1584)
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 82 of 117
Item No Description of Item Unit Rate
SECTION-3 REFRIGERATION, AIR-CONDITIONING , REFRIGERATORS
& CENTRAL HEATING SYSTEM
(ITEM NO 1501 to 1584)
REFRIGERATORS
1501 Supply and fix refrigerator, electric driven (single phase), capacity upto to 195 Litres .BEE 5 star rated
Each 18,382
1502 Supply and fix refrigerator, electric driven (single phase), capacity more than 195 Litres upto to 310 Litres.BEE 5 star rated
Each 26,609
1503
Supply and fix refrigerators, electric driven (single phase), capacity more than 310 Litres upto to 360 Litres .BEE 5 star rated
Each 41,527
1504 Supply and fix refrigerator, electric driven (single phase), capacity more than 360 Litres upto to 460 Litres .BEE 5 star rated
Each 65,501
WATER COOLER
1505
Supply and fix water cooler electric driven (single phase), having approx storage capacity of 40 litre and nominal cooling capacity of 40 Litres per hour.
Each 34,322
1506
Supply and fix water cooler electric driven (single phase), having approx storage capacity of 80 litre and nominal cooling capacity of 40 Litres per hour.
Each 38,819
1507
Supply and fix water cooler electric driven (single phase), having approx storage capacity of 120 litre and nominal cooling capacity of 60 Litres per hour.
Each 46,478
1508
Supply and fix water cooler electric driven (single phase), having approx storage capacity of 180 litres and nominal cooling capacity of 150 Litres per hour.
Each 57,524
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 83 of 117
Item No Description of Item Unit Rate
DEEP FREEZER
1509 Deep freezer hard top up to 320 litre capacity having single door.
Each 29,191
1510 Deep freezer glass top up to 320 litre capacity having single door.
Each 31,222
1511 Deep freezer hard top more than 320 litre and up to 400 Litre capacity having double door.
Each 32,682
1512 Deep freezer glass top more than 320 litre and up to 400 Litre capacity having double door.
Each 37,475
EVAPORATIVE COOLER (DESERT COOLER)
1513
Supply and fix desert cooler electric driven (single phase), having nominal air flow capacity of 4000 CuM per hour (or nearest size).Plastic/PVC Body
Each 11,141
1514
Supply and fix desert cooler electric driven (single phase), having nominal air flow capacity of 5000 CuM per hour (or nearest size).Plastic/PVC Body
Each 11,448
1515
Supply and fix desert cooler electric driven (single phase), having nominal air flow capacity of 4000 CuM per hour (or nearest size).Steel body
Each 7,734
1516
Supply and fix desert cooler electric driven (single phase), having nominal air flow capacity of 5000 CuM per hour (or nearest size).(Steel body)
Each 8,211
1517
Supply and fix desert cooler electric driven (single phase), having nominal air flow capacity of 6000 CuM per hour (or nearest size).(*Steel body)
Each 8,697
WINDOW AIR CONDITIONER
1518
Supply and fix room window type air conditioner electric driven (single phase), cooling capacity 4500 K Cal per hour ( 1.5 Ton).BEE 5 star rated
Each 42,194
1519
Supply and fix room window type air conditioner electric driven (single phase),cooling capacity 6000 K Cal per hour ( 2 Ton).BEE 5 star rated
Each 45,018
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 84 of 117
Item No Description of Item Unit Rate
1520 Add Rs 2000/- for cooling and heating type window A/Cs
Note:Window a/cs rate include th cost of wiring and switches etc
SPLIT AIR CONDITIONER
1521 Supply and fix air cooled split unit air conditioner electric driven, single phase of capacity of 1.5 TR, BEE 5 star rated
Each 46,796
1522 Supply and fix air cooled split unit air conditioner electric driven single phase of capacity of 2 TR, BEE 5 star rated
Each 54,530
1523 Add Rs 4000/- for cooling and heating type split A/Cs
Note:Split a/c rate include th cost of wiring and switches etc
AIR CONDITIONER CASSETTEE TYPE
1524 Supply and fix air cooled air conditioner electric driven, single phase of capacity of 2.0 TO 2.5 TR
Each 83,498
1525 Supply and fix air cooled air conditioner electric driven, single phase of capacity of 3.0 TO 3.5TR
Each 1,05,504
1526 Supply and fix air cooled air conditioner electric driven, single phase of capacity of 4.0 TO 5.0TR
Each 1,35,213
PACKAGE TYPE AIR CONDITIONING
1527
Supply and fix air conditioner package type suitable for operational on three phase AC electric supply, including water pump sets, cooling tower, ducting plumbing and electric connection, capacity 15000 K. cal Per hour (5 ton).
Each 5,72,167
1528
Supply and fix air conditioner package type suitable for operational on three phase AC electric supply, including water pump Sets, cooling tower, ducting plumbing and electric connection, capacity 22500 K cal Per hour (7.5 ton) or nearest size.
Each 6,27,183
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 85 of 117
Item No Description of Item Unit Rate
1529
Supply and fix air conditioner package type suitable for operational on three phase AC electric supply, including water pump Sets cooling towers, ducting plumbing and Electric connection, capacity 30000 K. Cal Per hour (10 ton) or nearest size.
Each 7,04,205
1530
Supply and fix air conditioners package type including heating arrangement suitable for operational on three phase AC electric supply, including water pump Sets cooling tower, ducting plumbing and Electric connection, with strip heater capacity 15000 K. Cal Per hour (5 ton) or nearest size.
Each 7,59,221
1531
Supply and fix air conditioner package type including heating arrangement suitable for operational on three phase AC electric supply, including water pump sets, cooling tower, ducting plumbing and Electric connection, with strip heater capacity 22500 K cal Per hour (7.5 ton) or nearest size.
Each 8,03,234
1532
Supply and fix air conditioner package type including heating arrangement suitable for operational on three phase AC electric supply, including water pump sets, cooling towers, ducting plumbing and electric connection, with strip heater capacity 30000 K cal Per hour (10 ton) or nearest size.
Each 8,47,247
CENTRAL AIR CONDITIONING PLANTS
1533
Supply and fix central air conditioning installations including AHUs, water pump sets, cooling towers, ducting and electrical connection suitable for 3 phase, AC supply direct expansion system capacity up to 10 Ton.
Per TR 1,02,309
1534
Supply and fix central air conditioning installations including AHUs,water pump sets cooling towers, ducting and electrical connection suitable for 3 phase, AC supply direct expansion system of capacity 11 to 20 TR
Per TR 93,274
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 86 of 117
Item No Description of Item Unit Rate
1535
Supply and fix central air conditioning installations including AHUs,water pump sets, cooling towers, ducting and electrical connection suitable for 3 phase, AC supply direct expansion system of capacity 21 to 40 TR
Per TR 91,623
1536
Supply and fix central air conditioning installations including AHUs, water pump sets cooling towers, ducting and electrical connection suitable for 3 phase, AC supply direct expansion system of capacity above 40 TR
Per TR 87,518
1537
Supply and fix central air conditioning installations including AHUs,water pump sets cooling towers, ducting and electrical connection suitable for 3 phase, AC supply chilled water system of capacity upto 40 TR
Per TR 1,06,617
1538
Supply and fix central air conditioning installations including AHUs, water pump sets, cooling towers, ducting and electrical connection suitable for 3 phase, AC supply chilled water system of capacity above 40 Ton and upto 100 TR
Per TR 94,908
1539
Supply and fix central air conditioning installations including AHUs,water pump sets, cooling towers, ducting and electrical connection suitable for 3 phase, AC supply chilled water system of capacity above 100 TR
Per TR 93,059
1540 Add for provisions of winter heating and humidification
Per TR Add 7.5%
1541 In case A/C by VRV/VRF tech per TR Rates of DX type to be adopted
PRECISION AIR CONDITIONING
1542 Supply and fix precision air conditioner capacity 21000 K cal Per hour (7 ton)
Per Job 17,98,082
1543 Supply and fix precision air conditioner capacity 30000 K cal Per hour (10 ton)
Per Job 21,25,501
1544 Supply and fix precision air conditioner capacity 750000 K cal Per hour (25 ton)
Per Job 48,91,505
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 87 of 117
Item No Description of Item Unit Rate
1545 Supply and fix precision air conditioner capacity 900000 K cal Per hour (30 ton)
Per Job 57,48,850
AIR CURTAIN
1546 Supply & fix air curtain 3 ft Each 13,294
1547 Supply & fix air curtain 4 ft Each 16,230
1548 Supply & fix air curtain 5 ft Each 20,293
1549 Supply & fix air curtain 6 ft Each 26,588
1550 Supply and fix air curtain sensor Each 3,693
CHEMICAL DEHUMIDIFIERS
1551
Supply and fix chemical dehumidifier continuous operating complete, with heaters, ducting, electrical connection for 100 Cfm capacity
Each 1,64,086
1552 do -- but for capacity 180 Cfm Each 2,14,023
1553 do -- but for capacity 360 Cfm Each 3,85,250
1554 do -- but for capacity 600 Cfm Each 6,42,069
1555 do -- but for capacity 900 Cfm Each 9,27,433
1556 do -- but for capacity 1200 Cfm Each 11,12,921
CENTRAL HEATING SYSTEM (Oil fired)
1557 S&F Central heating system of 25000 kcal/ Hr
Job 11,58,352
1558 -do- but 50000 (Kcal/Hr) Job 19,11,066
1559 -do- but 100000 (Kcal/Hr) Job 38,92,118
1560 -do- but 150000 (Kcal/Hr) Job 50,64,752
1561 -do- but 200000 (Kcal/Hr) Job 66,10,173
1562 -do- but 250000 (Kcal/Hr) Job 81,25,599
1563 -do- but 300000 (Kcal/Hr) Job 96,22,458
1564 -do- but 350000 (Kcal/Hr) Job 1,13,16,421
1565 -do- but 400000 (Kcal/Hr) Job 1,16,93,863
1566 -do- but 450000 (Kcal/Hr) Job 1,23,14,803
1567 -do- but 500000 (Kcal/Hr) Job 1,36,83,114
1568 -do- but 600000 (Kcal/Hr) Job 1,88,49,276
1569 -do- but 800000 (Kcal/Hr) Job 2,52,49,488
1570 -do- but1000000 (Kcal/Hr) Job 3,19,13,936
Note:Item 1557-1576 Rates includes all items of CHS viz boiler,piping,pumps(W+S),heat exchanger ,insulation,FCU, ducts, foundations etc, except cost of stand by boiler which is to be added seprately
BOILER(OIL FIRED) (1571 to 1584)
1571 S&F Boilers of Sizes 25000 (Kcal/Hr) Each 3,33,765
1572 -do- but sizes 50000 (Kcal/Hr) Each 5,03,027
1573 -do- but sizes 100000 (Kcal/Hr) Each 7,25,009
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 88 of 117
Item No Description of Item Unit Rate
1574 -do- but sizes 150000 (Kcal/Hr) Each 8,76,395
1575 -do- but sizes 200000 (Kcal/Hr) Each 10,90,666
1576 -do- but sizes 250000 (Kcal/Hr) Each 11,84,551
1577 -do- but sizes 300000 (Kcal/Hr) Each 14,96,885
1578 -do- but sizes 350000 (Kcal/Hr) Each 16,09,603
1579 -do- but sizes 400000 (Kcal/Hr) Each 18,60,666
1580 -do- but sizes 450000 (Kcal/Hr) Each 20,35,328
1581 -do- but sizes 500000 (Kcal/Hr) Each 20,63,100
1582 -do- but sizes 600000 (Kcal/Hr) Each 22,50,407
1583 -do- but sizes 800000 (Kcal/Hr) Each 31,09,145
1584 -do- but sizes 1000000 (Kcal/Hr) Each 42,11,198
Ser No 1585-2000 Blank
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 89 of 117
SECTION-4
TOOLS & PLANTS
(Item No 2201 to 2322)
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 90 of 117
Item No Description of Item Unit Rate
SECTION-4 TOOLS & PLANTS
(Item No 2201 to 2322)
ALUMINUM LADDER
2201 Self supporting cum extendable Aluminium Ladder of 12 feet extendable upto 21 feet.
Each 22,286
2202 Self supporting cum extendable Aluminium Ladder of 18 feet extendable upto 32 feet.
Each 34,717
2203 Normal Aluminium ladder of 12 feet Each 7,823
2204 Wall supported extendable aluminium ladder 12 feet extendable upto 12 feet
Each 12,337
2205 Wall supported extendable aluminium ladder 16 feet extendable upto 30 feet
Each 15,899
CRIMPING TOOLS
2206 Wire Stripper Each 329
2207 Cable cutter upto 10 Sqmm Each 670
2208 Pliers 1.5 Sqmm to 6 Sqmm Each 1,409
2209 Crimping pliers to crimp the end sealing ferrules from 0.5 to 16 Sqmm
Each 1,767
2210 Crimping pliers to crimp the end sealing ferrules from 0.5 to 16 Sqmm
Each 2,588
2211 Crimping pliers to crimp the end sealing ferrules from 16 to 50 Sqmm
Each 3,439
2212 Crimping pliers to crimp the end sealing ferrules from 10 to 95 Sqmm
Each 7,593
2213 Crimping pliers to crimp the end sealing ferrules from 95 to 185 Sqmm
Each 8,187
2214 Crimping pliers to crimp the end sealing ferrules from 95 to 400 Sqmm
Each 33,353
DIGITAL METER
2215 AC Power clamp on meter to measure KWH, KVA, KVAR Voltage
Each 34,491
2216 Digital insulation resistance meter 1000V, 0 - 2000 M ohm
Each 9,097
2217 Motor operated insulation tester 500 V, upto 1000M Ohm with carrying case and HV testing leads.
Each 27,289
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 91 of 117
Item No Description of Item Unit Rate
2218 Motor operated insulation tester 5000 V, upto 10000M Ohm with carrying case and HV testing leads.
Each 31,079
2219 Motor operated insulation tester 2500 V, upto 10000M Ohm with carrying case and HV testing leads.
Each 50,534
2220 Earth resistance tester 0 to 2000 Ohm complete with 4 spikes 4 test leads, charging lead and carrying case
Each 28,006
OTHER METER
2221 Digital Tachometer (Contact & Non-contact type)
Each 5,299
2222 Digital Sound level meter Each 16,411
2223 Digital thermo hygro meter Each 1,573
2224 High voltage testing kit for testing of electrical installation 0-5KV
Each 63,673
2225 Electrical metal scanner to detect PVC conduit/metal pipes behind tiles/concrete
Each 3,033
2226 Circuit breaker finder kit locate break in power circuit
Each 3,651
2227 Digital lux meter for measurement of light upto 50,000 lux
Each 7,543
2228 AC/DC digital clamp meter, 1000A DC/ 800A AC
Each 10,772
2229 Digital temperature and humidity meter Each 13,645
2230 Digital millimetre AC Each 26,334
2231 Digital sound level meter Each 29,184
DRILL & BLOWER
2232 Electric operated drill for drilling in steel for 10 mm dia hole.
Each 12,068
2233 Electric operated blower for air volume 2.7 cu meter/min
Each 8,831
COMMON HAND TOOLS
2234 Adjustable spanner of length 155mm confirming to IS-6149
Each 284
2235 Adjustable spanner of length 255mm confirming to IS-6149
Each 480
2236 Adjustable spanner of length 305mm confirming to IS-6149
Each 631
2237 Adjustable spanner of length 380mm confirming to IS-6149
Each 1,266
2238 Combination Pliers of 165 mm confirming to IS-3650
Each 323
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 92 of 117
Item No Description of Item Unit Rate
2239 Combination Pliers of 185 mm confirming to IS-3650
Each 342
2240 Combination Pliers of 210 mm confirming to IS-3650
Each 372
2241 Water pump plier of 200 mm confirming to IS-6118
Each 408
2242 Water pump plier of 250 mm confirming to IS-6118
Each 448
2243 Nose plier of 165 mm confirming to IS-3552 Each 326
2244 Side cutting plier of 165 mm Each 297
2245 Screw driver of 100 mm confirming to IS-844
Each 60
2246 Screw driver of 150 mm confirming to IS-844
Each 92
2247 Screw driver of 200 mm confirming to IS-844
Each 103
2248 Screw driver of 250 mm confirming to IS-844
Each 133
2249 Screw driver of 300 mm confirming to IS-844
Each 185
2250 Pipe wrench 250 mm confirming to IS-4003 Each 591
2251 Pipe wrench 300 mm confirming to IS-4003 Each 792
2252 Pipe wrench 450 mm confirming to IS-4003 Each 1,722
2253 Chain pipe wrench of size 4 confirming to IS-4123
Each 5,935
2254 Chain pipe wrench of size 6 confirming to IS-4123
Each 8,290
2255 Chain pipe wrench of size 8 confirming to IS-4123
Each 12,104
2256 Pipe vice of size 2 confirming to IS-6007 Each 3,578
2257 Pipe vice of size 4 confirming to IS-6008 Each 6,307
2258 Hammer with handle (Ball pein and cross pein) of 200 gms weight confirming to IS-841
Each 262
2259 Hammer with handle (Ball pein and cross pein) of 340 gms weight confirming to IS-842
Each 351
2260 Hammer with handle (Ball pein and cross pein) of 500 gms weight confirming to IS-843
Each 398
2261 Clave hammer with handle of 340 grm weight
Each 422
2262 Clave hammer with handle of 450 grm weight
Each 454
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 93 of 117
Item No Description of Item Unit Rate
2263 Double ended spanner (Plain) confirming to IS-2028 of size 6 x7 mm
Each 34
2264 Double ended spanner (Plain) confirming to IS-2028 of size 8 x9 mm
Each 33
2265 Double ended spanner (Plain) confirming to IS-2028 of size 8 x10 mm
Each 32
2266 Double ended spanner (Plain) confirming to IS-2028 of size 9 x11 mm
Each 34
2267 Double ended spanner (Plain) confirming to IS-2028 of size 10 x11 mm
Each 35
2268 Double ended spanner (Plain) confirming to IS-2028 of size 10 x12 mm
Each 37
2269 Double ended spanner (Plain) confirming to IS-2028 of size 12 x13 mm
Each 45
2270 Double ended spanner (Plain) confirming to IS-2028 of size 13 x16 mm
Each 54
2271 Double ended spanner (Plain) confirming to IS-2028 of size 14 x15 mm
Each 47
2272 Double ended spanner (Plain) confirming to IS-2028 of size 14 x17 mm
Each 61
2273 Double ended spanner (Plain) confirming to IS-2028 of size 16 x 17 mm
Each 61
2274 Double ended spanner (Plain) confirming to IS-2028 of size 18 x 19 mm
Each 74
2275 Double ended spanner (Plain) confirming to IS-2028 of size 18 x 21 mm
Each 79
2276 Double ended spanner (Plain) confirming to IS-2028 of size 19 x 22 mm
Each 82
2277 Double ended spanner (Plain) confirming to IS-2028 of size 20 x 22 mm
Each 104
2278 Double ended spanner (Plain) confirming to IS-2028 of size 21 x 23 mm
Each 131
2279 Double ended spanner (Plain) confirming to IS-2028 of size 24 x 26 mm
Each 135
2280 Double ended spanner (Plain) confirming to IS-2028 of size 24 x 27 mm
Each 147
2281 Double ended spanner (Plain) confirming to IS-2028 of size 25 x 28 mm
Each 191
2282 Double ended spanner (Plain) confirming to IS-2028 of size 30 x 32 mm
Each 196
2283 Ring spanner confirming to IS-2029 of size 6 x 7 mm
Each 71
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 94 of 117
Item No Description of Item Unit Rate
2284 Ring spanner confirming to IS-2029 of size 8 x 9 mm
Each 79
2285 Ring spanner confirming to IS-2029 of size 10 x 11 mm
Each 96
2286 Ring spanner confirming to IS-2029 of size 12 x 13 mm
Each 101
2287 Ring spanner confirming to IS-2029 of size 14 x 15 mm
Each 115
2288 Ring spanner confirming to IS-2029 of size 16 x 17 mm
Each 133
2289 Ring spanner confirming to IS-2029 of size 18 x 19 mm
Each 164
2290 Ring spanner confirming to IS-2029 of size 20 x 22 mm
Each 194
2291 Ring spanner confirming to IS-2029 of size 21 x 23 mm
Each 231
2292 Ring spanner confirming to IS-2029 of size 24 x 26 mm
Each 292
2293 Ring spanner confirming to IS-2029 of size 25 x 28 mm
Each 339
2294 Ring spanner confirming to IS-2029 of size 30 x 32 mm
Each 423
2295 Allen Keys of size 4 mm Each 17
2296 Allen Keys of size 6 mm Each 31
2297 Allen Keys of size 8 mm Each 51
2298 Allen Keys of size 10 mm Each 82
2299 Allen Keys of size 14 mm Each 220
2300 Allen Keys of size 17 mm Each 367
CENTRIFUGE MACHINE FOR TRANSFORMER OIL
2301 Centrifuge machine complete with filter Heater, pump suitable for 230 V AC supply for capacity 250 Litre/hr.
Each 3,63,845
2302 -do- but for capacity 500 Litre/hr. Each 3,94,165
2303 -do- but suitable for three phase supply 415 Volts and for capacity 1250 Litre/hr.
Each 5,21,284
2304 -d0- but suitable for three phase supply 415 Volts and for capacity 2000 Litre/hr.
Each 6,32,635
DISCHARGE ROD
2305 Wooden discharge rod PVC Coated suitable for 11 KV
Each 6,065
2306 -do- but for 33 KV Each 7,581
2307 Fibre glass discharged rod for 11 KV Each 17,435
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 95 of 117
Item No Description of Item Unit Rate
2308 -do- but for 33 KV Each 23,499
2309 Telestone type fibre glass discharge rod Each 33,353
CABLE FAULT LOCATING MACHINE
2310
Cable fault locating instrument suitable to locate and pin point faults in LT Cables to 33 KV cables including following instruments:- (i) Impulse generator 0-33 KV. (ii) Acoustic fault locator to pin point the fault exactly at fault point (iii) Reflectometer (Laptop based) TDR set =input wave capturing (iv) High voltage Murray loop for % distance to constant leakage faults
Each 13,46,419
2311 Route tracing instrument to trace the route of buried cable
Each 2,31,698
WATER SUPPLY
2312 Chlorine gas mask with jumbo canister Each 10,613
2313 Air breathing apparatus with cylinder for 30 min. duration
Each 58,216
2314 Emergency safety kit to stop leakage of chlorine gas from cylinder
Each 45,102
2315 Rubber/PVC hand gloves to handle chlorine gas/liquid
Each 455
2316 Rubber/PVC gum boots to handle chlorine gas/liquid
Each 2,275
2317 Chlorine gas leakage detector with sensor and alarm
Each 1,02,332
2318 New empty 100 Kgs capacity chlorine cylinder fitted with valves and valve guard
Each 46,997
2319 Chlorine test kit with coloured ample complete with all testing fitments and OT solution in Rexene finished box
Each 2,411
2320
PH test kit with coloured ample covered under BTB (range 6.0 to 7.0) or phenol red (range 6.8 to 8.4) with necessary fitments and 100 ml testing solution in Rexene finished box
Each 3,033
2321 Iron test kit Each 3,942
SWIMMING POOL
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 96 of 117
Item No Description of Item Unit Rate
2322 Suction Sweeper complete with motor, pump & starter, mounted on trolley including nylon rope, hose pipe float etc complete.
Each 1,09,002
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 97 of 117
SECTION-5 SEWAGE COLLECTION, TREATMENT, DISPOSAL & REUSE
(Item No 3001 to 3185)
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 98 of 117
5. PUBLIC HEALTH ENGINEERING
5.1 GRAVITY SEWERS (Item No 3001 to 3040)
RCC NP3 150 mm diameter Pipes laid on150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
Item No
For depth UNIT AMOUNT (Rupees)
TYPE OF BEDDING
(Type of Bedding to be decided by designer)
150 mm th. Moorum /Sand / Crushed stone
150 mm th. PCC Cradle
150 mm th. RCC Cradle with 0.4%
reinforcement
150 mm th. RCC Arch with 1% reinforcement PCC 1:4:8
3001 0.70m – 1.65 m RM 928 1,332 1,358 1,945
3002 1.65 – 2.30 m RM 1,492 1,896 1,921 2,381
3003 2.30 – 4.50 m RM 2,616 2,997 3,023 3,481
3004 4.50 m – 6.0 m RM 4,299 4,654 4,787 5,139
DWCPE (SN8) 180 (OD)/163(ID) mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
3005 0.70m – 1.65 m RM 1,224 As per IS 16098 (Part 2) : 2013 para A-4.1.2.4(a) any form of cement concrete structural bedding would not be necessary under normal conditions, even for maximum combined loading (wheel load + backfill). However designer may check requirement for special cases.
3006 1.65 – 2.30 m RM 1,788
3007 2.30 – 4.50 m RM 2,913
3008 4.50 m – 6.0 m RM 4,594
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 99 of 117
RCC NP3 200 mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
AMOUNT (Rs)
ITEM NO
FOR DEPTH UNIT
TYPE OF BEDDING
(Type of Bedding to be decided by designer)
150 mm th. Moorum /Sand
/ Crushed stone
150 mm th. PCC Cradle PCC 1:4:8
150 mm th. RCC Cradle with 0.4%
reinforcement
150 mm th. RCC Arch with 1% reinforcement
3009 0.70m – 1.65 m RM 1,068 1,532 1,563 2,238
3010 1.65 – 2.30 m RM 1,631 2,074 2,101 2,604
3011 2.30 – 4.50 m RM 2,756 3,157 3,184 3,667
3012 4.50 m – 6.0 m RM 4,437 4,804 4,942 5,305
DWCPE(SN8) 200 (OD)/175(ID)mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
3013 0.70m – 1.65 m RM 1,473 As per IS 16098 (Part 2) : 2013 para A-4.1.2.4(a) any form of cement concrete structural bedding would not be necessary under normal conditions, even for maximum combined loading (wheel load + backfill). However designer may check requirement for special cases
3014 1.65 – 2.30 m RM 2,037
3015 2.30 – 4.50 m RM 3,161
3016 4.50 m – 6.0 m RM 4,842
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 100 of 117
RCC NP3 250 mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
AMOUNT (Rs)
ITEM NO
FOR DEPTH UNIT
TYPE OF BEDDING
(Type of Bedding to be decided by designer)
150 mm th. Moorum /Sand /
Crushed stone
150 mm th. PCC Cradle PCC 1:4:8
150 mm th. RCC Cradle with 0.4%
reinforcement
150 mm th. RCC Arch with 1% reinforcement
3017 0.70m – 1.65 m RM 1,233 1,638 1,805 2,584
3018 1.65 – 2.30 m RM 1,795 2,160 2,313 2,865
3019 2.30 – 4.50 m RM 2,921 3,262 3,375 3,886
3020 4.50 m – 6.0 m RM 4,602 4,927 5,126 5,502
DWCPE(SN8) 300(OD)/260(ID) mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
3021 0.70m – 1.65 m RM 1,845 As per IS 16098 (Part 2) : 2013 para A-4.1.2.4(a) any form of cement concrete structural bedding would not be necessary under normal conditions, even for maximum combined loading (wheel load + backfill). However designer may check requirement for special cases.
3022 1.65 – 2.30 m RM 2,409
3023 2.30 – 4.50 m RM 3,534
3024 4.50 m – 6.0 m RM 5,216
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 101 of 117
RCC NP3 300 mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
AMOUNT (RS)
FOR DEPTH
TYPE OF BEDDING
(Type of Bedding to be decided by designer)
ITEM NO
150 mm th. Moorum /Sand
/ Crushed stone
150 mm th. PCC Cradle PCC 1:4:8
150 mm th. RCC Cradle with 0.4%
reinforcement
150 mm th. RCC Arch with 1% reinforcement
3025 0.70m – 1.65 m RM 1,410 2,025 2,065 2,956
3026 1.65 – 2.30 m RM 1,973 2,507 2,541 3,149
3027 2.30 – 4.50 m RM 3,099 3,550 3,580 4,123
3028 4.50 m – 6.0 m RM 4,780 5,176 5,324 5,714
RCC NP3 350 mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
3029 0.70m – 1.65 m RM 1,981 2,843 2,900 3,833
3030 1.65 – 2.30 m RM 2,544 3,234 3,278 4,061
3031 2.30 – 4.50 m RM 3,669 4,203 4,239 4,882
3032 4.50 m – 6.0 m RM 5,350 5,793 5,959 6,396
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 102 of 117
RCC NP3 400 mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
AMOUNT (Rs)
ITEM NO
FOR DEPTH UNIT
TYPE OF BEDDING
(Type of Bedding to be decided by designer)
150 mm th. Moorum /Sand / Crushed
stone
150 mm th. PCC Cradle PCC 1:4:8
150 mm th. RCC Cradle with 0.4%
reinforcement
150 mm th. RCC Arch with 1%
reinforcement
3033 0.70m – 1.65 m RM 2,171 3,117 3,178 4,233
3034 1.65 – 2.30 m RM 2,734 3,474 3,521 4,362
3035 2.30 – 4.50 m RM 3,860 4,421 4,458 5,134
3036 4.50 m – 6.0 m RM 5,541 5,999 6,170 6,623
RCC NP3 450 mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
3037 0.70m – 1.65 m RM 2,367 3,397 3,465 4,537
3038 1.65 – 2.30 m RM 2,931 3,724 3,775 4,676
3039 2.30 – 4.50 m RM 4,055 4,646 4,685 5,395
3040 4.50 m – 6.0 m RM 5,738 6,212 6,390 6,859
Notes for Sewers (3001 to 3040)
(a) Add extra percentage for exc. In soft rock – 15% and In hard rock –45 % (b) Add extra for pipes laid under sub-soil water conditions and/or in soils of treacherous nature,
by 6% for timbering, dewatering of trenches etc.
(c) Estimates include 4 MH per 100RM.
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 103 of 117
SEPTIC TANKS AND SHALLOW SEWER. (3051 to 3065)
RCC HUME PIPE SEPTIC TANKS
ITEM NO
On site Hume Pipe septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for
ITEM UNIT AMOUNT (Rupees)
3051 05 users. Each 15,870
3052 10 users. Each 26,450
LLDPE SEPTIC TANKS
ITEM NO
ITEM UNIT AMOUNT (Rupees)
On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for
CODE ITEM UNIT
AMOUNT (Rupees)
CONVENTIONAL With UPFLOW FILTER
INLCUDING MEDIA
3053 05 users. Each 23,299 28,023
3054 10 users. Each 41,813 50,176
3055 20 users. Each 79,438 95,325
3056 25 users. Each 1,01,162 1,21,394
3057 30 users. Each 1,22,854 1,47,423
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 104 of 117
RCC SEPTIC TANK
ITEM NO
ITEM UNIT AMOUNT (Rupees)
CONVENTIONAL With UPFLOW FILTER
RCC Septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter for
3058 50 users. Each 6,30,627 7,56,752
3059 100 users. Each 8,90,449 10,68,539
3060 150 users. Each 11,08,650 13,30,379
Notes for 3051 to 3060):
(1) Effluent from septic tank to be taken to nearby manhole/Sump/STP through shallow sewers. If this option is not available then it is to be disposed off in soakage pits.
(2) Septage from septic tank is to be pumped out once in a year and disposed off safely in nearby STP / Oxidation pond / Sludge drying beds.
SHALLOW SEWERS
ITEM NO
ITEM UNIT AMOUNT (Rs)
RCC NP3 DWCPE (SN8)
100 mm diameter Pipes laid on 150 mm thick moorum/sand/crushed stone bed with excavation up to depth 1.65 m in any type of soil, including manholes of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional.
3065 RM 690 660
Imp : for extra due to soil strata or high water table apply as per note for gravity sewers.
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 105 of 117
SOAL WELL (3068 to 3082)
SOAKAGE WELL
Imp : Soak pits must to be constructed in pair for each septic tank but to be used alternately.
Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size
ITEM NO
ITEM UNIT AMOUNT (Rs)
3068 1.2 M dia X 1.5 M effective depth Each 20,599
3069 1.2 M dia X 3 M effective depth Each 25,798
3070 1.2 M dia X 4.5 M effective depth Each 30,997
3071 1.8 M dia X 3.0 M effective depth Each 39,814
3072 1.8 M dia X 4.5 M effective depth Each 48,738
3073 1.8 M dia X 6.0 M effective depth Each 57,662
3074 2.4 M dia X 3.0 M effective depth Each 57,933
3075 2.4 M dia X 4.5 M effective depth Each 71,360
3076 2.4 M dia X 6.0 M effective depth Each 84,787
3077 3 M dia X 3.0 M effective depth Each 80,157
3078 3 M dia X 4.5 M effective depth Each 98,864
3079 3 M dia X 6.0 M effective depth Each 1,17,570
3080 3.6 M dia X 3.0 M effective depth Each 98,589
3081 3.6 M dia X 4.5 M effective depth Each 1,23,352
3082 3.6 M dia X 6.0 M effective depth Each 1,48,115
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 106 of 117
SUMP WELL CUM PUMP HOUSES (3101 to 3133)
Designing (hydraulically, structurally and aesthetically), and constructing RCC sumps in M-30 mix of required capacity including excavation in all types of strata, foundation concrete, container walls, bottom slab, top RCC roof slab with CI manhole covers and with plaster and water proofing as per zonal specification including epoxy paint inside, refilling of earth and disposal of surplus earth within 50 m lead, including all piping connections, valves, internal electrification, MS ladder, ventilation shaft, BB chambers with 5m of outer wall of tank complete including test for water tightness and hydraulic functioning. Top room as per zonal specifications included.
ITEM NO Av Flow (Cum/d)
Overall Depth of sump (m)
IL of incoming sewer (m)
Inner Dia of sump well (m)
Amount (Rs)
3101 Upto 50 6 upto 4.0 2 2,87,076
3102 upto 50 7 4.0 - 5.0 2 3,25,675
3103 51 - 100 6.5 upto 4.0 2 3,06,375
3104 51 - 100 7 4.0 - 5.0 2 3,25,675
3105 101 - 200 7 upto 4.0 2 3,25,675
3106 101 - 200 7.5 4.0 - 5.0 2.5 4,21,800
3107 201 - 200 8 5.0 - 6.0 3 5,28,722
3108 201 - 300 7 upto 4.0 2.5 3,98,798
3109 201 - 300 8 4.0 - 5.0 2.5 4,45,108
3110 201- 300 8.5 5.0 - 6.0 3 5,55,732
3111 301 - 400 7 upto 4.0 3 4,75,007
3112 301 - 400 8 4.0 - 5.0 3 5,28,722
3113 301 - 400 8.5 5.0 - 6.0 3.5 6,46,134
3114 401 - 500 8 upto 4.0 3 5,28,722
3115 401 - 500 8.5 4.0 - 5.0 3 5,55,732
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 107 of 117
ITEM NO Av Flow (Cum/d)
Overall Depth of sump (m)
IL of incoming sewer (m)
Inner Dia of sump well (m)
Amount (Rs)
3116 401 - 500 8.5 5.0 - 6.0 4 7,39,621
3117 501 - 600 8.5 upto 4.0 3 5,55,732
3118 501-600 8.5 4.0-5.0 3.50 6,46,134
3119 501 - 600 8.5 5.0 - 6.0 4.5 8,36,193
3120 601 - 800 8.5 upto 5.0 3.5 6,46,134
3121 601 - 800 8.5 5.0 - 6.0 4.5 8,36,193
3122 801 - 1000 8.5 upto 5.0 3.5 6,46,134
3123 801- 1000 8.5 5.0 - 6.0 4.5 8,36,193
3124 1001 - 1200 8.5 upto 5.0 4 7,39,621
3125 1001 - 1200 8.5 5.0 - 6.0 5 9,35,851
3126 1201 - 1400 8.5 upto 5.0 4 7,39,621
3127 1201 - 1400 8.5 5.0 - 6.0 5 9,35,851
3128 1401 - 1600 9 upto 5.0 4 7,74,037
3129 1401 - 1600 9 5.0 - 6.0 4.5 8,74,311
3130 1601 - 1800 9 upto 5.0 4 7,74,037
3131 1601 - 1800 9 5.0 - 6.0 5 9,77,671
3132 1801 - 2000 9 upto 5.0 4.5 8,74,311
3133 1801 - 2000 9 5.0 - 6.0 5.5 10,84,117
Note : For sump wells under sub-soil water conditions and/or in soils of treacherous nature, the rates of above items are to be increased by 6% for timbering, dewatering of trenches etc.
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 108 of 117
SUBMERSIBLE PUMPS (Item No 3134 to 3155)
Non clog vertical submersible pumps with chrome steel impeller and cutter, non-clog to pass 40 mm size particles including Supply, installation with guide rail and lifting chain, cables, Earthing, testing complete with 2 years maintenance
ITEM NO
Duty (Flow and head) lpm x m
H.P. of Pump
Amount
CODE
Duty (Flow and head) lpm x m
H.P. of Pump
Amount
3134 50x25 1 22,265 3146 600x25 5 28,316
3135 75x25 1 22,265 3147 600x40 7.5 41,431
3136 100x25 1 24,081 3148 700x40 10 48,623
3137 125x25 3 24,081 3149 800x40 10 48,623
3138 150x25 3 24,081 3150 900x40 10 65,490
3139 175x25 3 24,081 3151 1000x40 15 74,162
3140 200x25 3 24,081 3152 1250x40 20 82,307
3141 250x25 3 24,081 3153 1500x40 20 89,952
3142 300x25 3 24,081 3154 2000x40 30 1,35,727
3143 350x25 3 28,316 3155 2500x40 35 1,51,162
3144 400x25 3 28,316
3145 500x25 5 28,,316
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 109 of 117
5.6 Sewage Treatment Plant (MBBR Based). (Code 3171 to 3185)
MBBR BASED STPs
STP : PROCESS DESCRIPTION – MOVING BED BIO REACTOR (MBBR)
The Moving Media Bio Reactor Technology is a advanced biological treatment process which has a combination of activated
sludge process and attached growth process. The bio reactor has lot of packing material called carrier media in suspension
and provides a large surface area for micro organisms to grow and degrade the organic matter in aerobic condition. Due to
the use of carrier media, the higher concentration of bio mass is developed which helps to reduce the basin size, accept higher
loading rates and take shock loads.
The sewage after screening and grit removal flows by gravity into the BIO REACTOR wherein the attached growth, aerobic
microbes will utilize pollutant in presence of oxygen thereby, further reducing BOD. The air required will be provided through
coarse bubble air diffusers provided on the aeration grid at the bottom of reactor and using positive displacement, twin lobe,
root type air blower for supply of oxygen The PP media is provided in the aeration tank to allow the aerobic microbes to grow
and get attached. This media remains in fluid state in the aeration tank thereby keeping large number of microbial colonies
moving in the tank and provide high concentration of bio mass available at all the time. The microbes get exposed to bio
degradable organics in presence of oxygen and convert it into cell biomass, water molecule and carbon-dioxide. The microbial
colony grows on plastic media. The excess bio mass gets sloughed and moves with treated water into subsequent unit. This
sloughing action is a continuous process and the microbes keep on growing and sloughing. This is a very fast process and
hence system becomes self sustaining.
The dead bio mass generated will be separated in the CLARISETTLER TANK wherein tube media is provided for providing
additional surface area for settlement of bio mass and thereby reducing the space requirement. The solid-liquid separation is
achieved in this tank and clear supernatant will flow by gravity. The treated wastewater will be disinfected with Chlorine and
allowed to react in CHLORINE CONTACT TANK prior to suitable disposal.
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 110 of 117
TYPICAL CHARACTERITICS OF SEWAGE
(Note : Raw sewage are indicative only, actual tests must be carried out at site.)
Raw Sewage Quality
(refer table below for variations)
Treated Sewage Quality
Parameter Value Parameter Without tertiary
treatment
With Tertiary
Treatment
Temperature
=>200C
Temperature
Ambient
Ambient
pH
6.5 – 8.5
pH
6.5 - 8.5
6.5 – 8.5
TSS
250 – 300 mg/L
TSS
< 30 mg/L
< 10 mg/L
BOD5 at 20ºC
200 - 300 mg/L
BOD5at 200C
< 20 mg/L
< 10mg/L
COD
350 – 450 mg/L
FC MPN < 1000/ 100 ML < 230/100 ML
Oil & Grease
20 – 30 mg/L
Helminths Egg
<= 1 egg/L
FC MPN Very high Nitrate as N
<= 10mg/L
Phosphorus as P < = 5 mg/L
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 111 of 117
Actions for departure from standard Raw Sewage Characteristics
Temperature
pH
Total Suspended
Solids
BOD5 days at 20ºC
COD
Oil & Grease
MPN
< 200C
<6.5 or >8.5
>500mg/L
>400 mg/L
>600 mg/L
>30 mg/L
>107per 100 ML
Add 8% extra for every drop of 50C for heating
and insulation to keep sewage temp at 200C.
Any departure in pH requires detection and
isolation of source. To be treated separately.
Higher TSS shows ingress of surface runoff.
Additional capacity of Primary Settling Tank
required.
Higher BOD may be due to cattle farm/ butchery/
hospital. To be isolated and treated separately.
Higher COD may be due to industrial pollutants, to
be isolated and treated separately.
Higher oil & grease may be due to vehicle wash or
large kitchen waste. Additional Oil & Grease at
source required.
May be due to butchery/ hospital. To be isolated
and treated separately.
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 112 of 117
STP (MBBR) 100 to 600 Cum/day capacity
Designing (hydraulically, structurally & aesthetically), providing, constructing, hydraulic testing,
commissioning and giving satisfactory trials of STP consisting of Inlet chamber(RCC), Fine bar Screen
chamber(manual) RCC with steel screen, Oil & Grease Remover(RCC), Grit separator, Equalization Tank(
2 Tanks of 50% Capacity each), Air Grid for Equalization Tanks, Feed Pumps(2 No), Moving Bed Bio
Reactor(s) with plastic media (of appropriate density, size and quantity to keep very high MLSS > 15,000
mg/lit), Air Blowers for MBBR, Tube Settler assembly, Sludge Drying Bed of appropriate size, Chlorine
Dozing System, Chlorine contact tank, Foundation for all E/M equipments, Associated piping work with
required valves, gates, drains, pathways, Electrical control Panel with interconnecting cable, spare parts for
2 years of operation, etc. complete as turnkey job with all involved civil, electrical, digital and mechanical
works as per detailed specifications for civil, electrical and mechanical components with all duties and taxes
complete. (Also refer imp notes below).
For tertiary treatment it also includes Filter Feed Tank of RCC, Filter Feed Pumps, Dual Media Filter,
Activated Carbon Filter, Treated water Tank in RCC. Treated sewage can be used for irrigation,
horticulture, fire fighting and MT wash.
ITEM NO Capacity (Cum/day)
Equivalent population
Load (with 180 lpcd)
Land Area Required
(SM)
Rate (in Lakh)
with Tertiary Treatment
without Tertiary Treatment
3171 100 556 250 52.09 42.69
3172 200 1,111 250 61.55 50.46
3173 300 1,667 250 75.74 62.08
3174 400 2,222 300 90.26 73.99
3175 500 2,778 400 104.47 85.63
3176 600 3,333 400 118.26 96.93
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 113 of 117
STP (MBBR)above 600 Cum/D and upto 2000 Cum/D Capacity
Designing (hydraulically, structurally & aesthetically), providing, constructing, hydraulic testing,
commissioning and giving satisfactory trials of STP consisting of Coarse Bar Screening Chamber
(RCC) with steel screen (manual), Receiving Sump RCC, Submersible Pumps in receiving sump,
Stilling Chamber in RCC, Fine bar Screen chamber(manual) RCC with steel screen, Oil & Grease
Remover(RCC), Grit separator, Equalization Tank( 2 Tanks of 50% Capacity each), Air Grid for
Equalization Tanks, Feed Pumps(2 No), Moving Bed Bio Reactor(s) with plastic media (of
appropriate density, size and quantity to keep very high MLSS > 15,000 mg/lit), Air Blowers for
MBBR(2 Nos), Tube Settler assembly, Sludge Pump screw type(2 Nos), Sludge dewatering
centrifuge, Sludge holding tank, Air Grid for Sludge holding, Chlorine Dozing System, Chlorine
contact tank, Foundation for all E/M equipments, associated piping work with required valves,
gates, drains, pathways, Electrical control Panel with interconnecting cable, spare parts for 2
years of operation, etc. complete as turnkey job with all involved civil, electrical, digital and
mechanical works as per detailed specifications for civil, electrical and mechanical components
with all duties and taxes complete. (Also refer imp notes below).
For tertiary treatment it also includes Filter Feed Tank of RCC, Filter Feed Pumps, Dual Media
Filter, Activated Carbon Filter, Treated water Tank in RCC. Treated sewage can also be used
for irrigation, horticulture, fire fighting and MT wash.
ITEM NO Capacity (Cum/day)
Equivalent population Load (with 180 lpcd)
Land Area Required
(SM)
Rate (in Lakh)
with Tertiary Treatment
without Tertiary Treatment
3177 700 3,889 500 127.32 107.89
3178 800 4,445 500 139.89 118.55
3179 1000 5,556 600 164.04 139.02
3180 2000 11,111 750 271.41 230.01
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 114 of 117
STP (MBBR)above 2000 Cum/D
Designing (hydraulically, structurally & aesthetically), providing, constructing, hydraulic testing,
commissioning and giving satisfactory trials of STP consisting of Coarse Bar Screening Chamber
(RCC) with steel screen (manual), Receiving Sump RCC, Submersible Pumps in receiving sump,
Stilling Chamber in RCC, Fine bar Screen chamber(manual) RCC with steel screen, Oil & Grease
Remover(RCC), Grit separator, Equalization Tank( 2 Tanks of 50% Capacity each), Air Grid for
Equalization Tanks, Feed Pumps(2 No), Moving Bed Bio Reactor(s) with plastic media (of
appropriate density, size and quantity to keep very high MLSS > 15,000 mg/lit), Air Blowers for
MBBR(2 Nos), Tube Settler assembly, Sludge Pump screw type(2 Nos), Sludge thickener
centrifuge/ drum type, Sludge holding tank, Air Grid for Sludge holding, Chlorine Dozing System,
Chlorine contact tank, Chlorinator room, Foundation for all E/M equipments, Associated piping
work with required valves, gates, drains, pathways, Electrical control Panel with interconnecting
cable, administration block cum laboratory, laboratory equipments, spare parts for 2 years of
operation, etc. complete as turnkey job with all involved civil, electrical, digital and mechanical as
per detailed specifications for civil, electrical and mechanical components with all duties and
taxes complete. (Also refer imp notes below)
For tertiary treatment it also includes Filter Feed Tank of RCC, Filter Feed Pumps, Dual Media
Filter, Activated Carbon Filter, Treated water Tank in RCC. Treated sewage can also be used
for irrigation, horticulture, fire fighting and MT wash.
ITEM NO Capacity (Cum/day)
Equivalent population Load (with 180 lpcd)
Land Area Required
(SM)
Rate (in Lakh)
with Tertiary Treatment
without Tertiary Treatment
3181 3000 16,667 900 352.82 309.50
3182 4000 22,222 1050 435.59 382.10
3183 5000 27,778 1200 512.89 449.90
3184 10000 55,556 2300 850.66 746.20
3185 20000 111,111 3900 1,406.33 1,233.62
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 115 of 117
IMP NOTES FOR SEWAGE TREATMENT PLANTS
1. Peak factor considered for design for plants upto 3 MLD is 3; upto 15 MLD is 2.5 and upto 20
MLD is 2.0.
2. Upto 2 MLD capacity STP, chlorination is done by using sodium hypochlorite solution. Above 2
MLD capacity, gas chlorinator is provided.
3. Sludge thickener is not provided upto 3 MLD capacity STP. Sludge will be collected into sludge
sump and pumped directly to sludge dewatering system.
4. All water retaining structures are in M-30 grade of concrete.
5. Water table is considered 5 m below GL for design. Dewatering if required to be priced extra.
6. Soil bearing capacity is considered as 20 T/m² at 1.5 m below GL.
7. Lead for excavation is considered as 0.5 km within MD land.
8. Grade of cement used is OPC 43 grade. High Alumina Cement can also be used.
9. Grade of steel used is Fe 415.
10. Boundary wall, fencing, gate, storm water drains, approach roads, street lights, site clearance is
not considered in the scope.
11. Chemicals required during trial run and commissioning are not considered.
12. VAT has not been included in the rates.
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 116 of 117
CONCEPTUAL FLOW CHART FOR MBBR BASED STP UPTO 2 MLD
ESTIMIATING DATA 2016 FOR E/M and PHE WORKS OF MES
Page 117 of 117
CONCEPTUAL FLOW CHART FOR MBBR BASED STP ABOVE 2 MLD
Top Related