IVS-700HS Video Stabilizer 1st Edition - Rev.2
OPERATION MANUAL
Precautions Important Safety Warnings
[Power]
Operate unit only on the specified supply voltage.
Disconnect power cord by connector only. Do not pull on cable portion.
Do not place or drop heavy or sharp-edged objects on power cord. A damaged cord can cause fire or electrical shock hazards. Regularly check power cord for excessive wear or damage to avoid possible fire / electrical hazards.
[Grounding]
Ensure unit is properly grounded at all times to prevent electrical shock hazard.
Do not ground the unit to gas lines, units, or fixtures of an explosive or dangerous nature.
Ensure power cord is firmly plugged into AC outlet.
[Operation]
Do not operate unit in hazardous or potentially explosive atmospheres. Doing so could result in fire, explosion, or other dangerous results.
Do not allow liquids, metal pieces, or other foreign materials to enter the unit. Doing so could result in fire, other hazards, or unit malfunction.
If foreign material does enter the unit, turn power off and disconnect power cord immediately. Remove material and contact authorized service representative if damage has occurred.
[Transportation]
Handle with care to avoid shocks in transit. Shocks may cause malfunction. When you need to transport the unit, use the original packing materials or alternate adequate packing.
Stop
Caution
Hazard
Hazard
Caution
Hazard
Caution
Caution
[Circuitry Access]
Do not remove covers, panels, casing, or access circuitry with power applied to the unit! Turn power off and disconnect power cord prior to removal. Internal servicing / adjustment of unit should only be performed by qualified personnel.
Do not touch any parts / circuitry with a high heat factor. Capacitors can retain enough electric charge to cause mild to serious shock, even after power is disconnected. Capacitors associated with the power supply are especially hazardous. Avoid contact with any capacitors.
Unit should not be operated or stored with cover, panels, and / or casing removed. Operating unit with circuitry exposed could result in electric shock / fire hazards or unit malfunction.
[Potential Hazards]
If abnormal smells or noises are noticed coming from the unit, turn power off immediately and disconnect power cord to avoid potentially hazardous conditions. If problems similar to above occur, contact authorized service representative before attempting to again operate unit.
[Consumables]
The consumables used in unit must be replaced periodically. For further details on which parts are consumables and when they should be replaced, refer to the specifications at the end of the Operation Manual. Since the service life of the consumables varies greatly depending on the environment in which they are used, they should be replaced at an early date. For details on replacing the consumables, contact your dealer.
[Rubber Feet]
If this product has come with rubber feet attached by screws, do not insert the screws again without rubber feet after removing the rubber feet and screws. It may cause damage to the internal circuits or components of the unit. To install the rubber feet again to the unit, do not use other than the supplied rubber feet and screws.
Caution
Caution
Hazard
Stop
Caution
Upon Receipt Unpacking IVS-700HS units and their accessories are fully inspected and adjusted prior to shipment. Operation can be performed immediately upon completing all required connections and operational settings. Check your received items against the packing lists below.
ITEM QTY REMARKS
IVS-700HS 1
AC Cable 1
Rack Mount Brackets 1 pr. EIA standard type
Operation Manual 1
Check Check to ensure no damage has occurred during shipment. If damage has occurred, or items are missing, inform your supplier immediately. Rack Mounting The IVS-700HS can be mounted to EIA standard rack units. When rack mounting a unit, remove the rubber feet and use the accessory rack mount brackets (rack ears).
Table of Contents
1. Prior to Starting........................................................................................................................... 1 1-1. Welcome ............................................................................................................................ 1 1-2. About the IVS-700HS ......................................................................................................... 1 1-3. Usage Notes ...................................................................................................................... 2 1-4. About This Manual.............................................................................................................. 2
2. Panel Descriptions ..................................................................................................................... 3 2-1. Front Panel......................................................................................................................... 3 2-2. Rear Panel ......................................................................................................................... 4
3. Connection ................................................................................................................................. 6
4. Power ON................................................................................................................................... 7 4-1. Startup screen .................................................................................................................... 7 4-2. Menu Screen...................................................................................................................... 7
5. Operation ................................................................................................................................... 9 5-1. Menu List............................................................................................................................ 9
5-1-1. Operation Menu.......................................................................................................... 9 5-1-2. System Menu ........................................................................................................... 10
5-2. Operation ......................................................................................................................... 11 5-2-1. Button Operation ...................................................................................................... 11 5-2-2. Menu Operations...................................................................................................... 12
5-3. UNITY .............................................................................................................................. 14 5-3-1. Setting Parameters to UNITY................................................................................... 14 5-3-2. Setting UNITY Values............................................................................................... 14
6. Operation Setting ..................................................................................................................... 16 6-1. Video Shaking Correction (Stabilize) ................................................................................ 16 6-2. Correction Level ............................................................................................................... 16 6-3. Motion Filter ..................................................................................................................... 17 6-4. Enhance ........................................................................................................................... 17 6-5. Anti-alias Filter.................................................................................................................. 18 6-6. Freeze .............................................................................................................................. 18 6-7. Effective Area ................................................................................................................... 18 6-8. Correction Area ................................................................................................................ 20 6-9. Motion Detect Area........................................................................................................... 21 6-10. Video Clip Level (Clip Setting)........................................................................................ 22 6-11. Video Signal Standard (Signal Select) ............................................................................ 22 6-12. Sync Mode (Synchronous) ............................................................................................. 23
7. The Other Settings ................................................................................................................... 24 7-1. OPERATE / BY-PASS ...................................................................................................... 24
7-1-1. OPERATE ................................................................................................................ 24 7-1-2. BY-PASS .................................................................................................................. 24
7-2. OPERATION MODE......................................................................................................... 25 7-2-1. Menu Lock................................................................................................................ 25 7-2-2. Button Lock .............................................................................................................. 25 7-2-3. Serial and GPI Mode Setting.................................................................................... 25
7-3. Returning to Default ......................................................................................................... 26
8. Remote Control ........................................................................................................................ 27 8-1. RS-232C/422 Connector .................................................................................................. 27
8-1-1. If RS-232C Used.......................................................................................................27 8-1-2. If RS-422 Used .........................................................................................................28 8-1-3. Communication Protocol...........................................................................................29 8-1-4. Command List...........................................................................................................30 8-1-5. Error Message ..........................................................................................................32
8-2. GPI Connector ..................................................................................................................33 8-2-1. GPI Terminal Equivalent Circuit ................................................................................34
9. If Problems Occur .....................................................................................................................35
10. Specifications & Dimensions...................................................................................................36 10-1. Unit Specifications...........................................................................................................36 10-2. External Dimensions .......................................................................................................37
1
1. Prior to Starting
1-1. Welcome Congratulations! By purchasing IVS-700HS you have entered the world of FOR-A and its many innovative products. Thank you for your patronage and we hope you will turn to FOR-A products again and again to satisfy your video and audio needs. FOR-A provides a wide range of products, from basic support units to complex system controllers, which have been increasingly joined by products for computer video based systems. Whatever your needs, talk to your FOR-A representative. We will do our best to be of continuing service to you.
1-2. About the IVS-700HS The IVS-700HS is a multi-bit rate and multi-format digital video stabilizer optimized for broadcasting applications. It makes electrical corrections for video shaking occurring with a camera. It corrects the unsteadiness alone while maintaining the panning and tilt movements of the camera. It can also correct unsteadiness on video images for TV programs such as headline news, traffic and weather reports. The IVS-700HS is easy to install and incorporate into existing systems. Features
Accepts both HD SDI and SD SDI digital component signals
Capable of realtime image stabilization (2 frame delay)
Corrects only the unsteadiness while automatically recognizing panning and tilt movements
Video stabilization available both in LIVE and VCR videos
Capable of correcting an input signal up to 40% in the vertical/horizontal direction with respect to the screen
Provides precise sub-pixel level correction
Simple design - works by simply connecting the video cable without any special connections
Stabilizes only the data in the active area and keeps all the blanking data unchanged
Able to pass through the blanking data while compensating the processing delay
RS-232C/RS-422 or GPI remote control available
2
1-3. Usage Notes When shooting with the camera, use the highest possible shutter speed. Shooting moving objects with a slower shutter speed will result in a blurred and low-resolution image. A shutter speed of 1/240 sec. or less is recommended. This value, however, varies according to shooting subjects, shaking speed and other environments. Note that IVS-700HS may not get proper results with some video images as below.
1) Images that appear flat
Example: Images with uniform illumination of a wall or floor
2) Images with changing illumination in a single direction Example: Test signals such as Ramp/Color bar where the luminance level only changes horizontally, but not vertically.
3) Images with alternating changes in illumination Example: Images where an object such as a blind has changing light intensity that varies repeatedly at the same interval.
4) Images with multiple movements in different directions Example: Images where a big object crosses in front of the camera.
1-4. About This Manual This manual is intended to help the user easily operate the IVS-700HS and make full use of its functions during operations. Before connecting or operating your unit, read this operation manual thoroughly to ensure you understand the product. After reading, it is important to keep this manual in a safe place and available for reference.
3
2. Panel Descriptions
2-1. Front Panel (1) Power switch and indicator
Switch used to turn unit power ON / OFF. Power indicator will be lit green whenever power switch is set to ON and power applied to the unit.
(2) GENLOCK Indicator
Indicator lights whenever IVS-700HS signal is synced with external reference signal input to rear panel GENLOCK connector.
Indicator Indication Sync Signal
Lit IVS-700HS signal outputs synced to external signal input.
External reference signal
Not lit No external reference signal input connected (or input level too low). Internal timing signal used for reference.
Internal reference signal
(3) OPERATE/BY-PASS toggle switch
OPERATE (to left, light ON): Performs the shaking correction and outputs the corrected signals.
BY-PASS (to right , light OFF): Outputs the input signals without performing correction. See section 7-1. “OPERATE / BY-PASS.”
(4) ALARM indicator Indicator lights whenever the fan failure occurs.
(5) LOCK/OPERATE toggle switch Right side: The switch is set to Menu mode and menu settings can be made. Left side: The switch is set to Menu Lock mode and menu settings cannot be made (lit orange). The display panel shows “LOCK” when the switch is set to Menu Lock mode.
(6) Display panel (Vacuum-Fluorescent Display) Two line, 16-character per line, bright vacuum fluorescent display. This is used for both message and menu display.
(7) Menu Control Used to make menu settings. Parameters are changed (by turning the control clockwise or counterclockwise) and set (by pressing the control) while viewing the displayed information on the display panel (6).
VIDEO STABILIZER IVS-700HS
STABILIZE
OFF
OFF
ON
POWER
/BY-PASS*OPERATE
ALARM
*LOCK MENU
(PUSH)
FREEZE MODE ENHANCE
UNITYPUSH
MOTION FILTER
PUSH
HORIZONTAL
UNITY UNITY UNITY
VERTICAL
PUSH
HORIZONTAL
PUSH
VERTICAL
*ON
GENLOCK
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12)
4
(8) FREEZE Used to switch freeze operation ON/OFF. See section 6-6. “Freeze.” Left indicator lights whenever the FREEZE operation is set to ON.
(9) MODE Used to enter the System Mode. Press and hold down the MODE button for several seconds to enable the system mode. The LED lights up to indicate the unit is operating in system mode. Press the button again to return to the normal operation mode. See section 5-1-2. “System Menu.”
IMPORTANT
Be aware that when in the System Mode, a rectangle or a masked region that indicate the Effective Area, the Correction Area or the Motion Detect Area will be displayed on VIDEO OUT output screen. See section 4-2 "Menu Screen.”
(10)STABILIZE
Used to switch video shaking correction ON/OFF. See section 6-1 “Video Shaking Correction (Stabilize).” ON (to right, indicator light ON): Video shaking correction is performed. OFF (to left, indicator light OFF): Video shaking correction is not performed.
(11)MOTION FILTER HORIZONTAL: Used to adjust the horizontal motion filter for smooth correction. VERTICAL: Used to adjust the vertical motion filter for smooth correction. See section 6-3 “Motion Filter.” The MOTION FILTER can be set by turning the respective control. Each parameter can be set to the factory or user default (UNITY) by pressing the controls. Once the unity default setting is applied, the UNITY indicator at the left lights green. If the control is pressed again, the value can be changed by turning the control. See section 5-3 “UNITY.”
(12)ENHANCE HORIZONTAL: Used to adjust the horizontal edge enhancement. VERTICAL: Used to adjust the vertical edge enhancement. See section 6-4 “Enhance.” The ENHANCE can be set by turning the respective control. Each parameter can be set to the factory or user default (UNITY) by pressing the controls. Once the unity default setting is applied, the UNITY indicator at the left lights green. If the control is pressed again, the value can be changed by turning the control. See section 5-3 “UNITY.”
2-2. Rear Panel
RS-232C/422
GPI
HD-SDI/SD-SDI
VIDEO IN
HD-SDI/SD-SDI
VIDEO OUT
1 2
GENLOCK
RATING LABELAC100-120/220-240V ~ 50 / 60 H z IN
(1) (2) (3) (4) (5) (6) (3) (7) (8)
5
(1) RS-232C /RS-422 Used for serial control connection. 9-pin D-sub male. (RS-232C/RS-422 selectable.) See section 8-1 “RS-232C/422 Connector.”
(2) GPI Used for GPI control connection. 9-pin D-sub connector, female. See section 8-2 “GPI Connector.”
(3) FAN Used to air cool unit to prevent overheating. Do not block fan intake with other equipment or objects.
(4) VIDEO IN (HD/SD SDI) Used for serial digital component video input connection. Right connector is used to active throught out.
(5)VIDEO OUT (HD/SD SDI)1, 2 Used for serial digital component video output connection. The connectors will output the corrected video input from (4) VIDEO IN if the OPERATE/BY-PASS switch on the front panel is set to OPERATE. The VIDEO OUT1 outputs the input image directly if the switch is set to BY-PASS or the unit power is OFF. The VIDEO OUT2 doesn’t output any images if the switch is set to BY-PASS or the unit power is OFF. See the table below.
VIDEO OUT
Power ON/OFF
OPERATE / BY-PASS Setting Output Video Image
OPERATE Corrected image ON
BY-PASS Input image (uncorrected) 1 OFF --- Input image (uncorrected)
OPERATE Corrected image ON
BY-PASS None 2 OFF --- None
(6) GENLOCK
Used for input of external Black Burst or Tri Level sync reference signal. Front panel GENLOCK indicator lights when the GENLOCK signal is input to this connector. Right (loopthru) connector must be 75 ohm terminated if it isn’t connected to other system equipment.
IMPORTANT
The genlock input enables to align the horizontal phase of output video. (Phase-lock range: ±1/2H) The vertical phase lock function is not implemented. So input the reference signal of the same phase as SDI inputs.
(7)Ground Terminal
Used to ground unit to protect operators against static electricity and / or electrical shock.
(8) AC IN (AC 100-120/220-240V 50/60Hz) Used for connection to AC power source via supplied cable.
6
3. Connection Standard Connection Example
IMPORTANT
The HD/SD SDI VIDEO IN (serial digital component input) connector has an active- through output.
The GENLOCK connector has a loop-through output. The 75 ohm termination is needed if the input reference signal is not looped through.
RS-232C/422
GPI
HD-SDI/SD-SDI
VIDEO IN
HD-SDI/SD-SDI
VIDEO OUT
1 2
GENLOCK
RATING LABELAC100-120/220-240V ~ 50 / 60 H z IN
To other system equipment
Remote Switch or other GPI equipment
Camera
Must be 75 ohm terminated if not connected to other system equipment.
Reference Signal
7
(PUSH)
*LOCK MENU
4. Power ON
4-1. Startup screen Turn the Power switch to ON after all system connections are complete. The IVS-700HS firmware version is displayed at startup.
- H e l l o ! ! -
I V S - 7 0 0 H S V e r X X X
4-2. Menu Screen Promptly after the startup screen, the menu screen that indicates the current operation mode, the video input status, and the video format selected in the system menu will be displayed on the display panel as the figure below.
O P E R A T E V I D : I n
E C M 1 0 8 0 / 5 9 . 9 4 i
Item Display Description
OPERATE Operates in local mode. All process button and menu controls on the front panel are enabled.
LOCK Operates in local mode. However, all menu operations are locked and disabled.
Serial Operates in serial mode with RS-232C or RS-422. All process button and menu controls except setting display and “Control” menu setting on the front panel are disabled.
Operation Mode
GPI Operates in GPI mode. All process button and menu controls except setting display and “Control” menu setting on the front panel are disabled.
VID: In Input video signal is present. VID: No No input video signal is present. Video Input Status VID: Bp BY-PASS operation is functioning.
Effective Area E Displayed if the Effective Area is not set as the factory made default setting (See section 6-7.).
Correction Area C Displayed if the Correction Area is not set as the factory made default setting (See section 6-8.).
MD Area M Displayed if the Motion Detection Area is not set as the factory made default setting (See section 6-9.).
8
Item Display Description
Video Format
1080/59.94i 1080/60i 1080/50i 720/60p
720/59.94p 720/50p 525/60 625/50
The video signal format selected in the system menu.
IMPORTANT
When in the System Mode, a rectangle or a masked region that indicate the Effective Area, the Correction Area or the Motion Detect Area will be displayed on VIDEO OUT output screen unless they are set as the factory made default setting. To avoid this, check whether E, C or M is displayed on the menu screen when starting up the unit.
A message “UNLOCKED” will be displayed and flashing if a video not selected in the VIDEO FORMAT is received.
“FAN ERROR” will be displayed and flashing if a fan error occurs, and “POWER ERROR” will be displayed and flashing if there is a power malfunction. In both cases, turn the unit power OFF and contact your FOR-A supplier immediately.
9
5. Operation The IVS-700HS is operated using toggle switches, buttons and the menu screen on the front panel. If “LOCK” is displayed on the display panel, turn the LOCK/OPERATE toggle switch to “OPERATE”, and then make setting changes. The system-related settings can be made in the system menu. To change the parameter of the system menu, enter the system mode by holding down the MODE button for several seconds.
5-1. Menu List This section provides an explanation of all available IVS-700HS menu settings in order of the menu display. The parameters in the shaded cells are operated by the buttons or the toggle switches on the front panel. See section 5-2-1 “Button Operation“ for use of the buttons and the toggle switches and 5-2-2 “Menu Operations “ for instructions on operation menu. 5-1-1. Operation Menu
Feature Description Factory Setting Setting Range Ref.
Stabilize Switches video shaking correction ON/OFF. ON ON/OFF 6-1
Correction Level Sets the correction level. 5 0 to 15 6-2 VER 0 0 to 15 Motion
Filter HOR Adjusts the motion filter for smooth correction. 0 0 to 15
6-3
VER 0 0 to 15 Enhance
HOR Adjusts the edge enhancement. 0 0 to 15
6-4
VER 15 0 to 15 Anti-alias Filter HOR
Adjusts the anti-alias filter to reduce the jagged lines. 15 0 to 15
6-5
Button Switches Freeze operation ON/OFF. OFF ON/OFF
Freeze Menu Defines Freeze attribute. Odd Only
Frame Freeze, Odd Only, Even Only
6-6
Set Unity Sets the UNITY value of the Motion Filter and the Enhance.
--- Mot-F(H), Mot-F(V), ENH(H), ENH(V)
5-3-2
Control Sets the operation mode. Local Local, Serial, GPI 7-2
Serial Select Selects RS-232C or RS-422. RS-232C RS-232C,
RS-422 7-2-3
Control Lock Locks the operation button. OFF ON/OFF 7-2-2Software Version
(Hardware Version) Displays software and hardware versions.
VIDEO STABILIZER IVS-700HS
STABILIZE
OFF
OFF
ON
POWER
/BY-PASS*OPERATE
ALARM
*LOCK MENU
(PUSH)
FREEZE MODE ENHANCE
UNITYPUSH
MOTION FILTER
PUSH
HORIZONTAL
UNITY UNITY UNITY
VERTICAL
PUSH
HORIZONTAL
PUSH
VERTICAL
*ON
GENLOCK
Display and menu control
Control switch and buttons
10
IMPORTANT
The operation button status on the front panel and the menu settings will remain unchanged (except the FREEZE button) when the system is restarted. To restore all parameters to factory default, refer to section 7-3 “Returning to Default.”
5-1-2. System Menu The system menu can be viewed by turning the menu control. To change the system menu settings, enter the system mode by holding down the MODE button until the LED is lit. Press the button again to return to the normal operation. See section 5-2-2 “Menu Operations “ for menu settings. To make the operation easier, the Jog/Shuttle feature is available in the Motion Detect Area setting.
NOTE
When switching from the operation menu to the system menu, complete the settings, and then press the MODE button. Do not press the MODE button until the setting has been completed as well as when exitting from the system menu.
When in the System Mode, a rectangle or a masked region that indicate the Effective Area, the Correction Area or the Motion Detect Area will be displayed on VIDEO OUT output screen unless they are set as the factory made default setting. To avoid this, check whether E, C or M is displayed on the menu screen when starting up the unit.
Feature Description Factory Settings Setting Range Ref.
HD 16:9(+0) 16:9(+0) to 16:9(+7) (8 steps) 4:3(-7) to 4:3(+7) (15 steps)
SD 4:3(+0) 4:3(+0) to 4:3(+7) (8 steps) 16:9(-7) to 16:9(+7) (15 steps)
Start_HStart_VEnd_H
Effective Area
Sets effective area.
Adjust
End_V
Varies depending on the video signal.
6-7
Correction Area
Sets the correction area.
0 0 to 15 6-8
Normal Start_HStart_VEnd_H
Motion Detect Area
Sets the motion detect area.
Normal Adjust
End_V
Varies depending on the video signal.
6-9
Super-White OFF ON/OFF Super-Black OFF ON/OFF Clip Setting
Sets the video clip level. Chroma-Clip ON ON/OFF
6-10
Signal Select
Selects the video signal format.
1080/59.94i 1080/59.94i, 1080/60i 1080/50i, 720/60p 720/59.94p, 720/50p 525/60, 625/50
6-11
Synchro- nous
Selects the reference signal
Input Lock Genlock(BB) Genlock(TRI_S) Input Lock
6-12
11
5-2. Operation 5-2-1. Button Operation Stabilize can be switched ON/OFF using the toggle switch on the front panel. Although “Stabilize” is displayed in the menu, it is used only for display. For Motion Filter and the Enhance, turn each button on the front panel. When you turn the button, the setting value will be displayed in the menu. However, “Motion Filter” and “Enhance” menu are used only for display.
Feature Description Ref.Stabilize Used to switch video shaking correction ON/OFF. 6-1 Motion Filter Used to adjust the motion filter for smooth correction. 6-3 Enhance Used to adjust the edge enhancement. 6-4 Each parameter for the MOTION FILTER and ENHANCE can be set to UNITY (default) with a single press of a button. The UNITY values can also be set by the user. See section 5-3 “UNITY.”
VIDEO STABILIZER IVS-700HS
STABILIZE
OFF
OFF
ON
POWER
/BY-PASS*OPERATE
ALARM
*LOCK MENU
(PUSH)
FREEZE MODE ENHANCE
UNITYPUSH
MOTION FILTER
PUSH
HORIZONTAL
UNITY UNITY UNITY
VERTICAL
PUSH
HORIZONTAL
PUSH
VERTICAL*ON
GENLOCK
12
5-2-2. Menu Operations The procedures for selecting menus and making settings and adjustments are shown below (1) Turn the menu control on the front panel to select the menu item. (2) The current setting for the selected item is shown with
a flashing “>“ mark. (3) When the control is pressed, the setting item flashes to
indicate that the setting can be changed.
IMPORTANT
When the “>“ mark is flashing at the bottom right of the display panel, pressing the control makes the setting item flash so that the setting can be changed.
(4) Turn the control to change the setting for the selected menu item. (5) Press the control to apply the current setting.
Turn control(PUSH)
*LOCK MENUCorrection Level
7/15 (116%)
Flashing
Press control(PUSH)
*LOCK MENUCorrection Level
7/15 (116%)
Flashing
Signal Select 1080/59.94i >
Stabilize ON
First item
Last item
Turn control
Correction Level 5/15(111%) >
Synchronous Input Lock >
Flashing
Turn control(PUSH)
*LOCK MENUOPERATE VID:In
ECM 1080/59.94i
(PUSH)
*LOCK MENUCorrection Level
5/15 (111%) >
Flashing
Press control
(PUSH)
*LOCK MENUCorrection Level
5/15 (111%)
Flashing
13
Submenu
The procedure for submenu operation is the same as the procedure for menu operation. To return to the upper menu, select “ -to TOP- ” and press the control. For more detail about submenu operation, see section 5-3-2 “Setting UNITY Values.”
Jog/Shuttle Mode
The Jog Mode and the Shuttle Mode are available whenever “Adjust” is selected in the Mot-Detect (Motion Detect) Area under the system menu, <Selecting the Shuttle Mode> The mode selection item will be displayed at the bottom of the parameters in the sub menu. 1) Press the menu control when “Jog Mode” is displayed. 2) “>” will start flashing. 3) Turn the menu control and select the Shuttle Mode. 4) “Shuttle Mode” will start flashing. 5) Press the menu control to apply the setting Repeat the same procedure for returning to the Jog Mode. <Operating in the Shuttle Mode> Turning the menu control one step right (left) gradually increases (decreases) the setting
value. Turning the control one more step right (left) displays “>>”, and quickly increases (decreases) the setting value. To set the value, press the menu control. Four steps of speed are available in the Shuttle Mode and these steps of speed are
expressed as the number of the code “>”. The normal speed is represented by the ”>” , while the highest speed is represented by the “>>>>”.
14
5-3. UNITY Each parameter for the MOTION FILTER and ENHANCE can be set to UNITY (default) with a single press of a button. The UNITY values can also be set by the user. The procedures for setting parameters to UNITY and making UNITY values are described below.
IMPORTANT
To restore all parameters to factory default, refer to section 7-3 “Returning to Default.”
5-3-1. Setting Parameters to UNITY 1) Press the control once. The unity default setting is applied to the parameter and the
UNITY indicator at the left turns on. 2) Press the control again. The UNITY indicator turns off and the parameter is returned to the
control set value. You can adjust the value of the parameter again using the control. 5-3-2. Setting UNITY Values The user can set the desired UNITY values instead of the factory defaults. The setting procedure is as follows. (1) Turn the menu control on the front panel to display the “Set Unity” menu. (2) After verifying the “ > “ at the right of the menu is flashing, press the menu control to
access the setting stage. (3) When the control is pressed, the parameter names appear. Turn the control to select the
parameter (see the table below) whose UNITY value you want to. Abbrev. for Parameters Description Factory
Settings Setting Range
Mot-F (H) Motion Filter (Horizontal) 0 0 to 15 Mot-F (V) Motion Filter (Vertical) 0 0 to 15 ENH (H) Enhance (Horizontal) 0 0 to 15 ENH (V) Enhance (Vertical) 0 0 to 15
Aply Curr Value Applies the current value to UNITY for all parameters above.
--- ---
-to Top- Returns to the upper menu. --- --- (4)When the control is pressed, the setting value flashes to indicate that the setting can be
changed. Turn the control to change the value. (5) Press the control to apply the current setting.
Press control
HORIZONTAL
UNITY
MOTION FILTER
PUSHUNITY
PUSH PUSH
HORIZONTAL
UNITY
VERTICAL VERTICAL
UNITYPUSH
ENHANCE
N
15
Setting logic
IMPORTANT
The UNITY settings are kept even after the unit is powered off. However, they are returned to the factory default after the unit is initialized.
Turn to switch between Press to select Flashing
Set Unity Mot–F(H)13 /15 >
Set Unity ENH(V) 0 /15 >
Set Unity –to Top– >
0 - 15
Set Unity ENH(H) 0 /15 >
Set Unity Mot–F(V)13 /15 >
Set Unity Aply Curr Value >
Set Unity Mot–F(V)10/15
Set Unity Mot–F(H)10/15
Set Unity ENH(V) 3/15
Set Unity ENH(H) 3/15
0 - 15
0 - 15
0 - 15
Set Unity M: / E: / >
M: / E: / Cancel
M: / E: / Apply
16
6. Operation Setting In this chapter the labels as shown below give you at-a glance reference for how to set parameters.
Button Menu System Menu Menu Display UNITY Button JOG/SHUTTLE
6-1. Video Shaking Correction (Stabilize)
Button Menu Display
The STABILIZE switch is used to set video shaking correction ON/OFF. If the switch is set to ON, video shaking is corrected, and images are magnified based on the percentage set in section 6-2 “Correction Level.” If the switch is set to OFF, video shaking is not corrected, and images are magnified based on the percentage set in the menu. The input signals are bypassed and output from VIDEO OUT1 whenever the OPERATE/BY-PASS toggle switch on the front panel is set to BY-PASS regardless of the STABILIZE setting. The STABILIZE setting can be also checked in the “Stabilize” menu of the menu display. Note that the Stabilize menu is used only for display.
6-2. Correction Level
Menu
The “Correction Level” determines the correction range. This parameter can be set in the “Correction Level” menu. The image magnification percentage for this level is also displayed. If set higher, larger motions can be corrected, however, the corrected image can cover only a small area. If set lower, larger motions cannot be corrected, however, the corrected image can cover a large area. Settings less than 4 are effective for small vibrations caused by machines, winds, etc. Even if set to 0, video stabilization is available if the motions are small. Settings between 5 to 10 are effective for camera shake, wheel deflections, etc. Settings more than 10 are effective for high zooming or if an object is very close to the camera.
Covered area Large Small Corrected motion Small Default Large 0/ (100%) 5 (111%) 15 (143%)
HORIZONTAL
UNITY
MOTION FILTER
PUSHUNITY
PUSH PUSH
HORIZONTAL
UNITY
VERTICAL VERTICAL
UNITYPUSH
MODEFREEZE ENHANCESTABILIZE
*ONOFF
17
6-3. Motion Filter
Button Menu Display UNITY Button
MOTION FILTER determines the filtering level for video stabilization. The level can be set separately for Horizontal and Vertical in the range from 0 to 15. (0 Minimum strength, 15: Maximum strength) using the controls below. Set higher to use a filter giving priority to video stabilization. Set lower to use a filter giving priority to smoothness. Settings between 13 to 15 are effective for fixed point monitoring, such as for stationary cameras. Settings between 0 to 5 are effective for mobile cameras. The MOTION FILTER settings can be also checked in the “Motion Filter” menu of the menu display. Note that the “Motion Filter” menu is only used for display.
Motion of image Smooth JerkyEffectiveness Low High 0 15
NOTE
Each control can be pressed to set the parameter to UNITY (default). The user can set the desired UNITY values instead of the factory defaults. See section 5-3 “UNITY.”
6-4. Enhance
Button Menu Display UNITY Button
ENHANCE (edge enhancement) uses the image intensity gradient to enhance object boundaries. The enhance level can be adjusted separately for Horizontal and Vertical in the range from 0 to 15. The ENHANCE settings can be also checked in the “Enhance” menu of the menu display. Note that the “Enhance” menu is used only for display.
NOTE
Each control can be pressed to set the parameter to UNITY (default). The user can set the desired UNITY values instead of the factory defaults. See section 5-3 “UNITY.”
HORIZONTAL
UNITY
MOTION FILTER
PUSHUNITY
PUSH PUSH
HORIZONTAL
UNITY
VERTICAL VERTICAL
UNITYPUSH
MODEFREEZE ENHANCESTABILIZE
*ONOFF
HORIZONTAL
UNITY
MOTION FILTER
PUSHUNITY
PUSH PUSH
HORIZONTAL
UNITY
VERTICAL VERTICAL
UNITYPUSH
MODEFREEZE ENHANCESTABILIZE
*ONOFF
18
6-5. Anti-alias Filter
Menu
“Anti-alias Filter” menu is used to reduce the jagged diagonal lines when enlarging the images. This parameter can be set in the range from 0 to 15 levels. If set to 0, no anti-alias is applied. In contrast, setting to 15 applies the maximum strength of anti-alias.
6-6. Freeze
Button Menu
The FREEZE button switches freeze mode ON/OFF. Setting Video Freeze
1) Press button to set freeze mode ON (indicator light on). 2) Even or odd field freeze can be also selected in the “Freeze Mode” menu (See below).
Freeze Mode Setting Description Frame Freeze Freezes a frame
Odd Only Freezes an odd field (Default) Even Only Freezes an even field
Press button again to set freeze mode OFF (indicator light off).
6-7. Effective Area
System Menu Menu Display
The “Effective Area” determines the region where the image is displayed. The “Effective Area” setting is useful to reduce edge noise, especially for the blackish noise caused by video conversion between 4:3 and 16:9 images.
HORIZONTAL
UNITY
MOTION FILTER
PUSHUNITY
PUSH PUSH
HORIZONTAL
UNITY
VERTICAL VERTICAL
UNITYPUSH
MODEFREEZE ENHANCESTABILIZE
*ONOFF
Example1:16:9 Side Panel
Example2:4:3 Letter Box
19
Setting the Effective Area 1) Press and hold down the MODE button for several seconds until the LED is lit to enter the
system mode. 2) In the system mode, select the Effective Area menu. 3) While monitoring the VIDEO OUT image, set the Effective Area. This setting affects both the
width and height at the same time, at the same ratio, so the video keeps the same dimensions. However selecting 4:3 for 16:9 images or 16:9 for 4:3 images automatically cuts the height or the width of the image at first. And then setting the number value in the parentheses adjusts both the width and the height at the same time.
Setting Range
HD 16:9(+0) to 16:9(+7) (8 steps) 4:3(-7) to 4:3(+7) (15 steps)
SD 4:3(+0) to 4:3(+7) (8 steps) 16:9(-7) to 16:9(+7) (15 steps)
4) When “Adjust” is selected, following four parameters are appeared. Use these four
parameters to finely adjust the Effective Area.
When operating in the HD mode: Parameter Setting Range
Start_H 16:9(+0)to16:9(+7)(8 steps) 4:3(-7)to4:3(+7)(15 steps)
Start_V Normal(+0) to Normal(+7)(8 steps)
End_H 16:9(+0)to16:9(+7)(8 steps) 4:3(-7)to4:3(+7)(15 steps)
End_V Normal(+0) to Normal(+7)(8 steps) The aspect ratio is represented by 16:9 or 4:3. The number in the parentheses represents value for adjustment on a 2-pixel resolution.
When operating in the SD mode: Parameter Setting Range Start_H Normal(+0) to Normal(+7)(8 steps)
Start_V 4:3(+0)to4:3(+7)(8steps) 16:9(-7)to16:9(+7)(15steps)
End_H Normal(+0) to Normal(+7)(8 steps)
End_V 4:3(+0) to 4:3(+7)(8 steps) 16:9(-7) to 16:9(+7)(15 steps)
The aspect ratio is represented by 16:9 or 4:3. The number in the parentheses represents value for adjustment on a 2-pixel resolution.
IMPORTANT
While setting the Effective Area, a rectangle or a masked region that indicates the Effective Area will be displayed on VIDEO OUT output screen unless it is set as the factory made default setting. To avoid this, check whether “E” is displayed on the menu screen when starting up the unit. After the setting has been completed, the rectangle region will disappear. Note that setting the “Effective Area” lets the “Correction Area and “Motion Detect Area” return to factory default settings.
Setting Example1:16:9 Side Panel
Effective Area
(Start_H, Start_V) (4:3(+7), Normal(+7))
(End_H, End_V)(4:3(+7), Normal(+7))
Setting Example2:4:3 Letter Box
Effective Area
(Start_H, Start_V) (Normal(0), 16:9(-2))
(End_H, End_V)(Normal(+7), 16:9(+5))
Adjustable area
Effective Area
20
6-8. Correction Area
System Menu Menu Display
The “Correction Area” determines the region to be corrected in the image. The Correction Area can be set in the range from 0/15 to 15/15. When set to “0/15” (i.e., The Correction Area equals the Effective Area.): If the Correction Area exceeds the correction limit because the images are magnified based on the percentage set in the “Correction Level” (See section 6-2), an adequate stabilization cannot be made although the images will not be cut off. To correct the images, set the “Correction Level” higher. When set to “1/15” to “15/15”: Although a part of the images may be cut off after the correction, the images are corrected properly even when the Correction Area exceeds the correction limit where the correction area is set to “0/15”. Setting the Correction Area
1) Press and hold down the MODE button for several seconds until the LED is lit to enter the system mode.
2) In the system mode, select the Correction Area menu. 3) While monitoring the VIDEO OUT image, set the Correction Area.
Magnified
Input image Output image
When set to “0” (same as the Effective Area):
Correction Area Marker Cut off area
Magnified
Input image Output image
When set to “1” to “15”:
21
6-9. Motion Detect Area
System Menu Menu Display JOG/SHUTTLE
The “Motion Detect Area” determines the region where the Video Shaking Correction (Stabilize) is applied. Setting the Correction Area
1) Press and hold down the MODE button for several seconds until the LED is lit to enter the system mode.
2) In the system mode, select the Mot-Detect Area menu. 3) While monitoring the VIDEO OUT image, set the Mot-Detect Area. When “Adjust” setting is selected, the Motion Detect Area can be set by the parameter of the upper left corner point (Start-H, Start-V) and the lower right corner point (End-H, End-V)of the rectangular area (See the figure below). Setting Range of the Motion Detect Area (1080/59.94i, 1080/60i, 1080/50i)
Start_H 48 to 784 Start_V 27 to 385 End_H 176 to 912 End_V 155 to 513
Setting Range of the Motion Detect Area (720/60p, 720/59.94p, 720/50p) Start_H 32 to 480 Start_V 36 to 556 End_H 160 to 608 End_V 164 to 684
Setting Range of the Motion Detect Area (525/60) Start_H 18 to 310 Start_V 12 to 197 End_H 50 to 342 End_V 44 to 229
Setting Range of the Motion Detect Area (625/50) Start_H 18 to 310 Start_V 14 to 239 End_H 50 to 342 End_V 46 to 271
IMPORTANT
The “Motion Detect Area" cannot be set less than 128(H) x 128 (V) for HD, or 32(H) x 32 (V) for SD.
The value of the End-H and the End-V cannot be set smaller than the value of the Start-H and the Start-V. Note that the system will produce the mask signal to indicate the Motion Detect Area while Motion Detect Area setting. After the setting has been completed, the mask signal will disappear.
(Start_H, Start_V)
(End_H, End_V)
Motion Detect Area
22
6-10. Video Clip Level (Clip Setting)
System Menu Menu Display
The "Clip Setting" determines higher and lower levels of luminance and chrominance for video output signal. To go to the “Clip Setting” menu, enter the system mode by holding down the Mode button until the indicator lights.
Clip Setting Setting Description ON Sets higher luminance level to 1019 (approx.109%). Super-White OFF (default) Sets higher luminance level to 1940 (100%). ON Sets lower luminance level to 4 (approx.-7%). Super-Black OFF (default) Sets lower luminance level to 64 (0%). ON (default) Sets higher/lower chrominance levels to 960 (+100%)
/ 64 (-100%) Chroma-Clip
OFF Sets higher/lower chrominance levels to 1019 (approx. +113%) /4 (approx. -113%)
* The values above are 10-bit coded samples.
6-11. Video Signal Standard (Signal Select)
System Menu Menu Display
The “Signal Select” menu is for selecting the input video signal format. To go to the “Signal Select” menu, enter the system mode by holding down the Mode button until the indicator lights.
Video Signal Format 1080/59.94i, 1080/60i
1080/50i, 720/60p 720/59.94p, 720/50p
525/60, 625/50
23
6-12. Sync Mode (Synchronous)
System Menu Menu Display
The “Synchronous” is for selecting the sync signal format used in the IVS-700HS. To go to the “Synchronous” menu, enter the system mode by holding down the Mode button until the indicator lights.
Synchronous Setting Description
Genlock (BB) Uses the external reference signal (Black Burst) input from the GENLOCK connector on the rear panel.
Genlock (TRI_S) Uses the external reference signal (Tri Level sync) input from the GENLOCK connector on the rear panel.
Input Lock Uses the input video signal as a reference.
IMPORTANT
The genlock input enables to align the horizontal phase of output video. (Phase-lock range: ±1/2H) The vertical phase lock function is not implemented. So input the reference signal of the same phase as SDI inputs.
The items selected in the Signal Select menu and Synchronous menu are related each other. Below is a chart of valid reference video/ routed video combinations for the IVS-700HS. It is unable to select the invalid combinations.
1080/ 59.94i
1080/60i
1080/50i
720/ 60p
720/ 59.94p
720/ 50p 525/60 625/50
BB - - TRI_S - - - -
Input Lock
24
7. The Other Settings
7-1. OPERATE / BY-PASS You can use the toggle switch on the front panel to select the output signals to be corrected.
IMPORTANT
The OPERATE/BY-PASS toggle switch is disabled during remote control of the unit.
7-1-1. OPERATE The OPERATE / BY-PASS toggle switch should go to lit and corrected video signals are output.
NOTE
If Stabilize is set to OFF in the menu, the signals are not corrected, but the magnification percentage in the Correction Level setting is still enabled.
7-1-2. BY-PASS The OPERATE / BY-PASS toggle switch should go to unlit and the input signal is by-passed uncorrected.
*OPERATE/BY-PASS
VIDEO IN
VIDEO OUT1VIDEO OUT2
VIDEO IN (THRU)
IVS-700HS
Correction
*OPERATE/BY-PASS
VIDEO IN
VIDEO OUT1
VIDEO OUT2
VIDEO IN (THRU)
IVS-700HS
Correction
25
(PUSH)
*LOCK MENU
7-2. OPERATION MODE The operational mode status is displayed at the top of the menu display as shown in the table below.
O P E R A T E V I D : I n
E C M 1 0 8 0 / 5 9 . 9 4 i
Mode Display Description
OPERATE Operates in local mode. All process button and menu controls on the front panel are enabled.
-LOCK- Operates in local mode. However, all menu operations are locked and disabled.
-Serial mode- Operates in serial mode with RS-232C or RS-422. All process button and menu controls except setting display and “Control” menu setting on the front panel are disabled.
-GPI mode- Operates in GPI mode. All process button and menu controls except setting display and “Control” menu setting on the front panel are disabled.
7-2-1. Menu Lock The menu lock switch on the front panel enables / disables the use of the menu control. If the switch is set to left, the menu control is locked. 7-2-2. Button Lock All process control buttons indicated in the figure below can be also locked. This can be done by changing the “Control Lock” menu to ON. 7-2-3. Serial and GPI Mode Setting If you want to control the unit remotely, make an appropriate connection and change the “Control” menu from “Local” to “Serial” or “GPI.” If you select a “Serial” connection, then select the RS-232C or RS-422 in the “Serial Select” menu. See section 8 “Remote Control.”
(PUSH)
*LOCK MENULOCK VID:In
ECM 1080/59.94i
Right: Menu ModeLeft: Menu Lock Mode (Lit orange)
VIDEO STABILIZER IVS-700HS
STABILIZE
OFF
OFF
ON
POWER
/BY-PASS*OPERATE
ALARM
*LOCK MENU
(PUSH)
FREEZE MODE ENHANCE
UNITYPUSH
MOTION FILTER
PUSH
HORIZONTAL
UNITY UNITY UNITY
VERTICAL
PUSH
HORIZONTAL
PUSH
VERTICAL*ON
GENLOCK
All these controls are locked
26
7-3. Returning to Default If you need to return all settings to the factory made default settings, this can be done by turning power ON at the IVS-700HS while pressing and holding down the menu control. Refer to section. 5-1 “Menu List” for factory default settings.
IMPORTANT
Note that if you return all settings to default, user made UNITY settings are also returned to the factory settings.
27
8. Remote Control To control the unit remotely, change the menu setting to the “Remote Control.” See section 7-2-3 “Serial and GPI Mode Setting.”
8-1. RS-232C/422 Connector
8-1-1. If RS-232C Used
Communication parameters Baud rate 38400 [bps] Data length 8 [bit] Stop bit 1 [bit] Parity None X parameter (flow control) None Send text interval More than 0 [ms] Command interval More than 10 [ms]
RS-232C Pin Assignment Table (9-pin D-sub male) Pin No. Signal Description
1 OPEN N/C 2 RxD Receive data 3 TxD Transmit data 4 OPEN N/C 5 GND Signal ground 6 OPEN N/C 7 RTS Request to send. Uses internal connection to CTS. 8 CTS Clear to send. Uses internal connection to RTS. 9 OPEN N/C
IMPORTANT
If connecting to a computer or other device, use a RS-232C cross cable with a length of 10 m or less.
RS-232C/422
GPI
HD-SDI/SD-SDI
VIDEO IN
HD-SDI/SD-SDI
VIDEO OUT
1 2
GENLOCK
RATING LABELAC100-120/220-240V ~ 50 / 60 H z IN
28
8-1-2. If RS-422 Used Communication parameters
Baud rate 38400 [bps] Data length 8 [bit] Stop bit 1 [bit] Parity None X parameter (flow control) None Send text interval More than 0 [ms] Command interval More than 10 [ms]
RS-422 Pin Assignment Table (9-pin D-sub male)
Pin No. Signal Signal Details 1 GND Ground 2 Transmit A (T-) 3 Receive B (R+) 4 Open 5 Open 6 Open 7 Transmit B (T+) 8 Receive A (R-) 9 GND Ground
IMPORTANT
The connection with the normal RS-422 interface has a different pin arrangement, and so a special cable is used that matches this pin arrangement. Be sure that the connection distance does not exceed 100 m.
29
8-1-3. Communication Protocol Setting value: Command [Space] Setting Value [Enter] The value is set to the parameter invoked by the command Getting value: Command [Enter] The parameter value invoked by the command is displayed. Input text: ASCII No echo back of the input text is performed from the IVS-700HS. The communication systems shown above are performed using the input keys shown in the table below. Input Keys
Command Uppercase letter from A to Z - [Space] Space (20H) Delimiter for command and dataSetting value
Hexadecimal expression using 1 to 9 and A to F -
CR(0DH) [Enter]
LF(0AH)*Can be omitted Single-line delimiter
The menu setting values are displayed after entering Command [Space] Command Data [Enter]. (See examples 1 and 2.) Example 1: When STABI [Space] 01 [Enter] is entered from the terminal. (Input system 1)
Input: STABI 01[CR+LF] ASCII code: [53H][54H][41H][42H][49H][20H][30H][31H][0DH][0AH] Return: Write: 01
Example 2: When STABI [Enter] is entered from the terminal. (Input system 2) Input: STABI [CR+LF] ASCII code: [53H][54H][41H][42H][49H][0DH][0AH] Return: Read: 01
Example 3:
Input: STABI 0123[CR+LF] Return: Write : 01 (Only 01 is valid.)
The input value is displayed as a 2-digit hexadecimal value using 0 to 9 and A to F. If a value with more than two digits is entered, the first two digits from the top are used.
30
8-1-4. Command List Table of Comparing between Local and Serial Control Commands
Local Control commands Serial control commands Input value (Hex)
00 OPERATEBy-pass / Operate Switch BYPAS 01 BY-PASS
Lock Switch - - - 00 ON
Stabilize Switch STABI 01 OFF
Correction Level Menu CORRECT 00 to 0F HORIZONTAL MOTH 00 to 0F
Motion Filter VERTICAL
Volume MOTV 00 to 0F
HORIZONTAL ENHH 00 to 0F Enhance
VERTICAL Volume
ENHV 00 to 0F HORIZONTAL AAFH 00 to 0F Anti-alias
Filter VERTICAL Menu
AAFV 00 to 0F 00 OFF
Freeze Button FRZS 01 ON 00 Odd 01 Even Freeze Mode Menu FRZM 02 Frame
Set Unity Menu - - 00 Local 01 Serial Control Menu CTRL (*1) 02 GPI
Serial Select Menu - - Control Lock Menu - - Software Version (Hardware Version) Menu VERSION Display only
00 OFF Mode Button MODE (*2)
01 ON The parameters in the shaded cells are operated by the buttons or the toggle switches on the front panel. (*1) CTRL command If CTRL is not set to “01”, any command other than the CTRL command is rejected, and an error code is returned. However, the CTRL command can change the control setting from Serial even if the control is not at Serial. During serial remote control, control operations on the front panel only allow viewing of the setting values of the menus. (However, the setting values for the Control menu can be changed.) The OPERATE/BY-PASS toggle switch is disabled. (The LED of the OPERATE/BY-PASS toggle switch turns on and off according to the serial remote setting.) (*2) MODE command If MODE is set to “00”, the system menu parameters cannot be changed. Before changing the system menu parameters, set MODE to “01.”
31
Local Control commands Serial control commands Input value (Hex)
00 Displays corrected image
- EAREA 01 Displays Effective
Area 00 HD4:3 SD16:9
- EFMOD 01 Adjust
4:3 HD
00 to 07 08 to 16
16:9 (8 steps) 4:3 (15 steps)
16:9 SD
FRAME 00 to 07 08 to 16
4:3 (8 steps) 16:9 (15 steps)
00 to 16 HD Start_H ESTRH
00 to 07 SD 00 to 07 HD
Start_V ESTRV 00 to 16 SD 00 to 16 HD
End_H EENDH 00 to 07 SD 00 to 07 HD
Effective Area
Adjust
End_V
System menu
EENDV 00 to 16 SD
Correction Area System menu CORA 00 to 0F
00 Displays corrected image
- MAREA 01 Displays Motion
Detect Area 00 HD4:3 SD16:9
- MDMOD 01 Adjust
Normal - - 0030~0310 (1080) 0020~01E0 (720)
0012~0136 (525/60) Start_H MSTRH
0012~0136 (625/50) 001B~0181 (1080) 0024~022C (720)
000C~00C5 (525/60) Start_V MSTRV
000E~00EF (625/50) 00B0~0390 (1080) 00A0~0260 (720)
0032~0156 (525/60) End_H MENDH
0032~0156 (625/50) 009B~0201 (1080) 00A4~02AC (720)
002C~00E5 (525/60)
Motion Detect
Area
Adjust
End_V
System menu
MENDV
002E to 010F (625/50) 00 OFF
Super-White CSWH 01 ON 00 OFF
Super-Black CSBL 01 ON 00 OFF
Clip Setting
Chroma-Clip
System menu
CSCH 01 ON
(Continued to next page.)
32
Local Control commands Serial control commands Input value (Hex)
00 525/60 01 625/50 02 1080/60i 03 1080/59.94i 04 1080/50i 05 720/60p 06 720/59.94p
Signal Select System menu INSEL
07 720/50p 00 Input Lock 01 Genlock (BB) Synchronous System
menu SYNC 02 Genlock (TRI_S)
8-1-5. Error Message Error messages are displayed in the following cases. Command or data could not be received correctly. Commands were not executed in the correct mode.
The error message displays the received character string and the error code. Refer to the table below for descriptions of the error codes. Note that the command is cancelled if the received data is determined to be an error. Therefore, the command must be entered again. Error Codes
ERROR CODE Description
00 The input code does not match section 8-1-4 “Command list.”
01 Characters other than 0 to 9 or A to F in hexadecimal expressions were entered for the setting value.
02 A value that exceeds the setting range was entered.
04 CTRL was not set to “01”, and a command other than the CTRL command was entered.
05 The parameter is protected by the MODE command. (Effective Area, Mot-Detect Area, Corrective Area, Input Select, Synchronous)
06 The selected sync signal format is not supported by the selected video format.
Example 1: Input: CTRL 05[CR+LF] Return: ERROR : 02
33
8-2. GPI Connector The pin arrangement for the GPI connector is shown below. This arrangement cannot be changed.
GPI Control Pin Assignment Table (9-pin D-sub female) Pin No. Signal Details I/O Function High Low
1 VCC +5V
2 OPERATE / BY-PASS Output See sec. 7-1. BY-PASS OPERATE
3 VIDEO IN Output Input video/None None Input video
4 FAN ALARM Output - No fault Fault occurred
5 Stabilize Output See sec.6-1. OFF ON
6 OPERATE / BY-PASS Input See sec. 7-1. OPERATE BY-PASS
7 Stabilize Input See sec. 6-1. ON OFF 8 Not Used Input - 9 GND Ground
RS-232C/422
GPI
HD-SDI/SD-SDI
VIDEO IN
HD-SDI/SD-SDI
VIDEO OUT
1 2
GENLOCK
RATING LABELAC100-120/220-240V ~ 50 / 60 H z IN
34
8-2-1. GPI Terminal Equivalent Circuit a) Example of connection with GPI output circuit
*1) Use a protective resistance at the proper value according to the internal/external supply voltage and LED characteristics.
b) Example of connection with GPI input circuit
IVS-700HS side
6-8PIN
9PIN22Ω
DC5V-24V(External power supply)
IVS-700HS side +5V
22Ω 0.5W
22Ω
(*1) 1PIN
2-5PIN
9PIN
Select usage of internal or external power supply.
Control device side
35
9. If Problems Occur If any of the following problems occur during operation of your IVS-700HS, proceed as indicated below to see if problem can be corrected before assuming a unit malfunction has occurred.
Problem Check Action
“Control Lock” menu setting Verify the “Control Lock” set to OFF. See section 7-2-2.
Unity indicator Verify the Unity indicator light OFF. See section 5-3-1.
Cannot control at front panel
Operation Mode display at the panel and “Control” menu setting
Verify the “Control” menu set to “LOCAL.” See section 7-2.
Cannot use menu control
Operation Mode display at the panel and menu lock switch setting
Verify the menu lock switch set to right. See section 7-2-1.
Input video signal not bypassed when set to BY-PASS
VIDEO OUT connectors Verify cable is connected to VIDEO OUT1 connector. (VIDEO OUT2 and MONOTOR OUT never output bypass video) See section 2-2.
“Control Lock” menu Verify “Control Lock” set to OFF. See section 7-2-2.
Freeze operation not set when FREEZE button pressed OPERATE/BY-PASS switch Verify OPERATE/BY-PASS set to
“OPERATE.” See section 7-1-2.
36
10. Specifications & Dimensions
10-1. Unit Specifications Standard 1080/59.94i, 1080/60i, 1080/50i, 720/59.94p, 720/60p, 720/50p,
525/60, 625/50 (Select from the menu) Signal Processing 4: 2: 2 component Sampling Frequency HD SDI Y:74.25/1.001MHz, 74.25MHz
C:37.125/1.001MHz, 37.125MHz SD SDI Y: 13.5 MHz,
C: 6.75 MHz Quantization 10-bit Video Input Serial digital component:
HD SDI 1.485/1.001Gbps, 1.485Gbps or SD SDI 270Mbps 1 ea., BNC with active thru, 75 ohm
Video Outputs Serial digital component: HD SDI 1.485/1.001Gbps, 1.485Gbps or SD SDI 270Mbps 2 ea., BNC, 75 ohm
Genlock Input Tri-level Sync ±0.3Vp-p or Black Burst 0.429Vp-p (525/60), 0.450Vp-p (625/50) 1 ea., BNC, 75ohm (terminatation required) or loopthru Input phase-lock range:±1/2H against genlock input
Output Image Size 1920×1080 pixels (1080/59.94i, 1080/60i, 1080/50i), 1280×720 pixels (720/59.94p, 720/60p, 720/50p), 720×486 pixels(525/60), 720×576 pixels (625/50) Image size varies according to the input image size and Correction Level setting in the menu.
Total Delay 2 frames (without frame synchronizer) Correction Function Correction range: maximum 40 percentage for both vertical and
horizontal Frequency Response 1Hz to 59.94/2Hz (1080/59.94i, 720/59.94p, 525/60)
1Hz to 60/2Hz (1080/60i, 720/60p) 1Hz to 50/2Hz (1080/50i, 720/50p, 625/60) for both vertical and horizontal (theoretical values)
Motion Type Vertical, horizontal, and diagonal (two-dimensional) Interfaces
RS-232C/422 9-pin D-sub, 1ea. (male) GPI 9-pin D-sub, 1ea. (female)
TTL negative logic level or make contact (max. 5V to 24VDC 40mA) Temperature 0–40 °C Humidity 30%–90% (no condensation) Power 100 VAC–120 VAC or 220 VAC–240 VAC±10%, 50 Hz/60 Hz Consumption 68VA (48W) at 100VAC
67VA (48W) at 240VAC Dimensions 424 (W)×350 (D)×44 (H) mm EIA 1U Weight 7.0 kg
37
10-2. External Dimensions
(All dimensions in mm)
VIDEO STABILIZER IVS-700HSSTABILIZE
OFF
OFF
ON
POWER
/BY-PASS*OPERATE
GENLOCK ALARM
*LOCK MENU
(PUSH)
FREEZE MODE ENHANCE
UNITY
PUSH
MOTION FILTER
PUSH
HORIZONTAL
*ON
UNITY UNITY UNITY
VERTICAL
PUSH
HORIZONTAL
PUSH
VERTICAL
RS-232C/422
GPI
HD-SDI/SD-SDI
VIDEO IN
HD-SDI/SD-SDI
VIDEO OUT
12
GENLOCK
RATING LABEL
482
465
424
34440
32042
1
400
1244
6
40
t2.3
326
4040
21
AC100-120/220-240V ~ 50 / 60 Hz IN
2 x 2 - 6. 4 x 12ø 20
Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
09/29/2009 Printed in Japan
FOR-A COMPANY LIMITED Head Office : 3-8-1 Ebisu, Shibuya-ku, Tokyo 150-0013, Japan Overseas Division Phone: +81 (0)3-3446-3936, Fax: +81 (0)3-3446-1470 Japan Branch Offices : Osaka/Okinawa/Fukuoka/Hiroshima/Nagoya/Sendai/Sapporo R&D/Production : Sakura Center/Sapporo Center
FOR-A America Corporate Office 11125 Knott Ave., Suite #A, Cypress, CA 90630, USA Phone: +1 714-894-3311 Fax: +1 714-894-5399
FOR-A America East Coast Office Two Executive Drive, Suite 670, Fort Lee Executive Park, Fort Lee NJ 07024, USA Phone: +1 (201) 944-1120 Fax : +1 (201) 944-1132
FOR-A America Distribution & Service Center 2400 N.E. Waldo Road, Gainesville, FL 32609, USA Phone: +1 352-371-1505 Fax: +1 352-378-5320
FOR-A Corporation of Canada 346A Queen Street West, Toronto, Ontario M5V 2A2, Canada Phone: +1 416-977-0343 Fax: +1 416-977-0657
FOR-A Latin America & the Caribbean
5200 Blue lagoon Drive, Suite 760, Miami, FL 33126, USA Phone: +1-305-931-1700 Fax: +1-305-264-7890
FOR-A UK Limited UNIT C71, Barwell Business Park, Leatherhead Road, Chessington Surrey, KT9 2NY, UK Phone: +44 (0)20-8391-7979 Fax: +44 (0)20-8391-7978
FOR-A Italia S.r.l.
Viale Europa 50 20093, Cologno Monzese (MI), Milan, Italy Phone: +39 02-254-3635/6 Fax: +39 02-254-0477
FOR-A Corporation of Korea 801 Dangsan Bld., 53-1 Dangsan-Dong, Youngdeungpo-Gu, Seoul 150-800, Korea Phone: +82 (0)2-2637-0761 Fax: +82 (0)2-2637-0760
FOR-A China Limited 708B Huateng Building, No. 302, 3 District, Jinsong, Chaoyang, Beijing 100021, China Phone: +86 (0)10-8721-6023 Fax: +86 (0)10-8721-6033
*The contents of this manual are subject to change without notice.
Top Related