Download - Dynamo Meter

Transcript
  • 7/31/2019 Dynamo Meter

    1/30

    Click to edit Master subtitle style

    5/23/12

    Studies

    School of Engineering and

    Applied ScienceMechanical and IndustrialEngineering Department

    Presentation ofprinciple of Dynamo-

    meter

    Edited by: Tarik NElbusefi

    Supervising : Dr. Hussam El-DinEl-Sheikh

  • 7/31/2019 Dynamo Meter

    2/30

    5/23/12

    The existence of some physicalvariables like force, temperature etcand its magnitude or strength cannot

    be detected or quantified directly butcan be so through their effect(s) only.For example, a force which canneither be seen nor be gripped butcan be detected and also quantifiedrespectively by its effect(s) and theamount of those effects (on some

    material) like elastic deflection,

    General principle of

    measurement.

  • 7/31/2019 Dynamo Meter

    3/30

    5/23/12

    These effects, called signals, oftenneed proper conditioning for easy,accurate and reliable detection and

    measurement. And one way for measure the

    cutting forces are by instrument

    called dynamometerwhere wetrying to describe its design andprincipal of his work

  • 7/31/2019 Dynamo Meter

    4/30

    5/23/12

    Physical variable(cutting force, temp.

    etc.)

    Conversion intoanother suitable

    variable (deflection,expansion etc)

    Amplification,filtration andstabilization

    Reading or recording

    Transducing stage

    (1)

    Conditioning stage

    (2)

    Read out stage

    (3)

    Signal

    Conditionedsignal

    General principle ofmeasurement

  • 7/31/2019 Dynamo Meter

    5/30

    5/23/12

    Stage 1 : The target physicalvariable (say force) is convertedproportionally into another suitablevariable (say voltage) called signal, byusing appropriate sensor ortransducer.

    Stage 2 : The feeble and noisysignal is amplified, filtered, rectified (ifnecessary) and stabilized forconvenience

    The measurement process iscomprised of three stages asillustrated in previous slide:

  • 7/31/2019 Dynamo Meter

    6/30

    5/23/12

    Different types of transducers usedin dynamometers for measuring

    machining forces.Measurement of cutting force(s) is based onthree basic principles :(A) measurement of elastic deflection of abody subjected to the cutting force(B) measurement of elastic deformation, i.e.strain induced by the force

    (C) measurement of pressure developed in amedium by the force.The type of the transducer depends upon

    how that deflection, strain or pressure is

    detected and quantified.

  • 7/31/2019 Dynamo Meter

    7/30

    5/23/12

    (A) Measuring deflection causedby the cutting force(s)

    Under the action of the cuttingforce, say PZ in turning, the tool ortool holder elastically deflects asindicated in next Fig. Such tooldeflection, is proportional to the

    magnitude of the cutting force, PZ,simply as,

  • 7/31/2019 Dynamo Meter

    8/30

    Click to edit Master subtitle style

    5/23/12

    PZ L

    where, L = overhang or equivalent projected length of thecantilever

    type tool (holder)E = physical property (Youngs modulus of elasticity

    of the beam)

    I = size (plane moment of inertia) of the beamsection.Since for a given cutting tool and its holder, E and I

    are fixed and the equation 1 becomeswhere, K= is a constant of proportionality.

    1

  • 7/31/2019 Dynamo Meter

    9/30

    5/23/12

    Deflection measurement.

    The deflection, , can be measured: mechanically by dial gauge (mechanical

    transducer)

    electrically by using several transducerslike;

    potentiometer; linear or circular

    capacitive pickup

    inductive pickup LVDT

    as schematically shown in next slide

  • 7/31/2019 Dynamo Meter

    10/30

    5/23/12

    (a)

    (d)

    (c

    )

    (b)

    d

    R

    E

    fixedcoilmoving

    core

    Electrical transducers working based on deflectionmeasurement

    (a) linear pot(b) circular pot(c) capacitive pick up (d) LVDT

    type Version

    Figure(1)

  • 7/31/2019 Dynamo Meter

    11/30

    5/23/12

    Design requirementsfor Tool force

    DynamometersFor consistently accurate and reliable

    measurement, the following

    requirements are considered duringdesign and construction of any tool forcedynamometers :

    SensitivityRigidity

    Cross sensitivity

  • 7/31/2019 Dynamo Meter

    12/30

    5/23/12

    Design requirements- Cont

    Sensitivity :the dynamometershould be reasonably sensitive for

    precision measurementRigidity:the dynamometer need

    to be quite rigid to withstand the

    forces without causing muchdeflection which may affect themachining condition

    Cross sensitivity : the

  • 7/31/2019 Dynamo Meter

    13/30

    5/23/12

    Construction and workingprinciple of some common tool

    force dynamometers.The dynamometers being commonly used now-

    a-days for measuring machining forces desirablyaccurately and precisely (both static anddynamic characteristics) are

    either strain gauge type

    or piezoelectric type

    Strain gauge type dynamometers are

    inexpensive but less accurate and consistent,whereas, the piezoelectric type are highlyaccurate, reliable and consistent but veryexpensive for high material cost and stringent

    construction.

  • 7/31/2019 Dynamo Meter

    14/30

    5/23/12

    Turning Dynamometer(over view)

    Turning dynamometers may be straingauge or piezoelectric type and may beof one, two or three dimensionscapable to monitor all of PX, PY and PZ.For ease of manufacture and low cost,strain gauge type turningdynamometers are widely used and

    preferably of 2 D (dimension) forsimpler construction, lower cost andability to provide almost all the desired

    force values.

  • 7/31/2019 Dynamo Meter

    15/30

    5/23/12

    Turning Dynamometer

    Design and construction of a strain gaugetype 2 D turning dynamometer are shownschematically in next slide Fig (2) andphotographically in Fig (3,4)Two full bridges

    comprising four live strain gauges areprovided for PZ and PX channels which areconnected with the strain measuring bridge fordetection and measurement of strain in termsof voltage which provides the magnitude ofthe cutting forces through calibration. Fig (5)pictorially shows use of 3 D turningdynamometer having piezoelectric transducersinside.

  • 7/31/2019 Dynamo Meter

    16/30

    5/23/12

    Figure(2)

  • 7/31/2019 Dynamo Meter

    17/30

    5/23/12

    Photographs of a strain gauge type 2 D turningdynamometer and its major components.

    Figure

    (3)

    Figure

    (4)

  • 7/31/2019 Dynamo Meter

    18/30

    5/23/12

    Use of 3 D piezoelectric type turningdynamometer.

    Figure(5)

  • 7/31/2019 Dynamo Meter

    19/30

    5/23/12

    Drilling dynamometerPhysical construction of a strain gauge

    type 2 D drilling dynamometer formeasuring torque and thrust force istypically shown schematically in next slideFig (6) and pictorially in after next slide

    Fig (7,8) Four strain gauges are mountedon the upper and lower surfaces of thetwo opposite ribs for PX channel andfour on the side surfaces of the other two

    ribs for the torque channel. Before use,the dynamometer must be calibrated toenable determination of the actual valuesof T and PX from the voltage values orreading taken in SMB or PC.

  • 7/31/2019 Dynamo Meter

    20/30

    5/23/12

    Schematic view of construction of a strain gaugetype drilling dynamometer.

    Figure(6)

  • 7/31/2019 Dynamo Meter

    21/30

    5/23/12

    A strain gauge type drilling dynamometer andits major components.

    Figure(7)

    Figure(8)

  • 7/31/2019 Dynamo Meter

    22/30

    5/23/12

    Milling dynamometer

    Since the cutting or loading point is notfixed w.r.t. the job and the dynamometer,the job platform rests on four symmetricallylocated supports in the form of four O-rings.

    The forces on each O-ring are monitored andsummed up correspondingly for getting thetotal magnitude of all the three forces in X, Yand Z direction respectively. Fig. (9) shows

    schematically the principle of using O-ringfor measuring two forces by mounting straingauges, 4 for radial force and 4 fortransverse force.

  • 7/31/2019 Dynamo Meter

    23/30

    5/23/12

    Scheme of strain gauge type 3 D milling

    dynamometer

    Figure(9)

  • 7/31/2019 Dynamo Meter

    24/30

    5/23/12

    Milling dynamometer -Cont

    Fig. (10) typically shows configurationof a strain gauge type 3 D millingdynamometer having 4 octagonal rings.

    Piezoelectric type 3 D dynamometersare also available and used formeasuring the cutting forces in milling(lain, end and force)

  • 7/31/2019 Dynamo Meter

    25/30

    5/23/12

    A typical strain gauge type 3 D millingdynamometer

    Figure(10)

  • 7/31/2019 Dynamo Meter

    26/30

    5/23/12

    Grinding dynamometer

    The construction and application ofa strain gauge type (extended O-ring)grinding surface dynamometer andanother piezoelectric type are typicallyshown in Fig. (11) and Fig. (12)respectively. Unlike strain gauge typedynamometers, the sophisticated

    piezoelectric type (KISTLER)dynamometers can be used directlymore accurately and reliably even

    without calibration by the user.

  • 7/31/2019 Dynamo Meter

    27/30

    5/23/12

    A typical strain gauge type 2 D grindingdynamometer

    Figure(11)

  • 7/31/2019 Dynamo Meter

    28/30

    5/23/12

    Piezoelectric type grinding dynamometer in

    operation.

    Figure(12)

  • 7/31/2019 Dynamo Meter

    29/30

    5/23/12

    Dont hesitate to ask

    any question

  • 7/31/2019 Dynamo Meter

    30/30

    5/23/12

    Thank you foryour attention