PSC-Schnittstelle
Patentanmeldung 1988; Markteinführung 1990 >Capto<
Polygonal taper interface with flange surface contact ISO 26623-1
Polygon geschliffen und gehärtet auf 44 bis 52 HRC
Greiferrille gehärtet auf 50 – 58 HRC
Rohlingseite in weichem Zustand und zerspanbar
Material: 1.7218 (25CrMo4) Rohlingseite auf 600 – 800 Nm vergütet
PSC 32 Artikelnummer aticle number
D A
thb.ps032.006 32 90
thb.ps032.007 32 125
thb.ps032.001 40 110
thb.ps032.002 50 125
thb.ps032.003 70 60
thb.ps032.004 90 70
PSC 40 Artikelnummer article number
D A
thb.ps040.001 40 95
thb.ps040.010 40 165
thb.ps040.005 60 65
thb.ps040.002 60 165
thb.ps040.003 80 75
thb.ps040.004 100 85
thb.ps040.006 110 70
thb.ps040.007 125 105
PSC 50
Artikelnummer aticle number
D A
thb.ps050.001 50 125
thb.ps050.009 50 175
thb.ps050.002 75 175
thb.ps050.005 80 100
thb.ps050.003 90 80
thb.ps050.006 95 150
thb.ps050.004 110 90
PSC 63
Artikelnummer aticle number
D A
thb.ps063.004 63 180
thb.ps063.008 63 195
thb.ps063.001 75 195
thb.ps063.002 110 85
thb.ps063.003 130 95
thb.ps063.005 155 105
PSC 80
Artikelnummer aticle number
D A
thb.ps080.001 80 200
thb.ps080.002 120 160
thb.ps080.003 130 90
thb.ps080.004 165 105
PSC Interface Applied for patent 1988; Market introduction 1990 >Capto< Polygonal taper interface with flange surface contact ISO 26623-1 Polygon ground and hardened to 44 - 52 HRC Gripper groove hardened to 50 – 58 HRC Shaft part not hardened and easily machineable
Material: 1.7218 (25CrMo4) Shaft part tempered to 600 – 800 Nm
PSC-Schnittstelle Patentanmeldung 1988; Markteinführung 1990 >Capto< Polygonal taper interface with flange surface contact ISO 26623-1 Polygon und Greiferrille geschliffen und gehärtet Rohlingseite auf 1.100 – 1.300 Nm vergütet
Material: 1.8519 (31CrMoV9) oder 1.8159 (51CrV4)
PSC Interface Applied for patent 1988; Market introduction 1990 >Capto< Polygonal taper interface with flange surface contact ISO 26623-1 Polygon and gripper groove ground and hardened Shaft part tempered to 1,100 – 1,300 Nm
Material: 1.8519 (31CrMoV9) or 1.8159 (51CrV4)
PSC 32 Artikelnummer aticle number
D A
thb.ps032.008 50 150
thb.ps032.005 60 90
thb.ps032.009 90 150
thb.ps032.010 120 100
PSC 40 Artikelnummer aticle number
D A
thb.ps040.008 40 120
thb.ps040.011 50 180
thb.ps040.009 80 120
thb.ps040.012 90 150
thb.ps040.013 120 120
PSC 50 Artikelnummer aticle number
D A
thb.ps050.007 50 150
thb.ps050.013 50 200
thb.ps050.008 63 180
thb.ps050.010 90 180
thb.ps050.011 120 200
thb.ps050.012 150 150
PSC 63 Artikelnummer aticle number
D A
thb.ps063.009 70 200
thb.ps063.010 90 200
thb.ps063.006 110 120
thb.ps063.011 120 150
thb.ps063.007 120 180
thb.ps063.012 180 120
thb.ps063.013 220 120
PSC 80
Artikelnummer aticle number
D A
thb.ps080.009 90 200
thb.ps080.005 100 200
thb.ps080.010 110 250
thb.ps080.006 145 200
thb.ps080.007 150 200
thb.ps080.008 160 120
thb.ps080.011 180 120
PSC 100
Artikelnummer aticle number
D A
thb.ps100.001 100 100
thb.ps100.002 100 200
thb.ps100.003 150 100
thb.ps100.004 150 200
thb.ps100.005 160 150
thb.ps100.006 200 100
HSK-A Schnittstelle DIN 69893-1 Form A; ISO 12164-1 Style A Kegel und Greiferrille geschliffen und gehärtet auf 50 – 58 HRC Rohlingseite in weichem Zustand und zerspanbar Material: 16MnCr5 Rohlingseite auf 600 - 800 Nm vergütet
HSK-A Interface DIN 69893-1 Form A; ISO 12164-1 Style Taper and gripper groove ground and hardened to 50 – 58 HRC Shaft part not hardened and easily machineable Material: 16MnCr5 Shaft part tempered to 600 - 800 Nm
HSK-A 63 Artikelnummer aticle number
D A
thb.ha063.001 63 100
thb.ha063.002 63 140
thb.ha063.003 63 160
thb.ha063.004 63 200
thb.ha063.005 63 250
thb.ha063.009 63 350
thb.ha063.006 80 160
thb.ha063.007 80 250
thb.ha063.008 108 140
HSK-A 80 Artikelnummer aticle number
D A
thb.ha080.001 80 160
thb.ha080.002 80 250
HSK-A 100 Artikelnummer aticle number
D A
thb.ha100.001 63 200
thb.ha100.002 80 250
thb.ha100.003 90 300
thb.ha100.008 92 330
thb.ha100.009 93 250
thb.ha100.004 97 250
thb.ha100.005 100 160
thb.ha100.006 100 250
thb.ha100.010 103 160
thb.ha100.011 103 200
thb.ha100.012 103 315
thb.ha100.007 182 160
HSK-A 25
Artikelnummer aticle number
D A
thb.ha025.001 25 100
HSK-A 32
Artikelnummer aticle number
D A
thb.ha032.001 25 150
thb.ha032.002 32 100
thb.ha032.003 40 120
HSK-A 40
Artikelnummer aticle number
D A
thb.ha040.001 40 100
thb.ha040.002 40 150
thb.ha040.003 40 160
HSK-A 50
Artikelnummer aticle number
D A
thb.ha050.001 50 100
thb.ha050.002 50 150
thb.ha050.003 50 200
thb.ha050.004 52 200
thb.ha050.005 63 160
thb.ha050.006 63 200
HSK-C 32 Artikelnummer aticle number
D A
thb.hc032.001 40 160
thb.hc032.002 32,5 160
HSK-C 40 Artikelnummer aticle number
D A
thb.hc040.001 50 160
thb.hc040.002 40,5 160
thb.hc040.003 80 200
thb.hc040.004 70 100
HSK-C 50 Artikelnummer aticle number
D A
thb.hc050.001 63 200
thb.hc050.002 50,5 200
HSK-C 63
Artikelnummer aticle number D A
thb.hc063.001 80 200
thb.hc063.002 63,5 250
HSK-C 80
Artikelnummer aticle number D A
thb.hc080.001 80,5 250
thb.hc080.003 100 100
HSK-C 100
Artikelnummer aticle number D A
thb.hc100.001 93,5 250
HSK-C Schnittstelle DIN 69893-1 Form C ISO 12164-1 Style C Kegel und Greiferrille geschliffen und gehärtet auf 50 – 58 HRC Rohlingseite in weichem Zustand und zerspanbar Material: 16MnCr5 Rohlingseite auf 600 - 800 Nm vergütet
HSK-C Interface DIN 69893-1 Form C ISO 12164-1 Style C Taper and gripper groove ground and hardened to 50 – 58 HRC Shaft part not hardened and easily machineable Material: 16MnCr5 Shaft part tempered to 600 - 800 Nm
TS-Schnittstelle Patentanmeldung 1987; Markteinführung 1989 >KM< Modular taper interface with ball track system ISO 26622-1 Material: 1.8519 (31CrMoV9 ) oder 1.8159 (51CrV4) Rohlingseite auf 1.150 – 1.300 Nm vergütet
TS-Interface Applied for patent 1987; Market introduction 1989 >KM< Modular taper interface with ball track system ISO 26622-1 Material: 1.8519 (31CrMoV9) or 1.8159 (51CrV4) Shaft part tempered to 1.150 – 1.300 Nm Taper and gripper groove ground and inductive hardened to 44 - 52 HRC
TS 40 Artikelnummer aticle number
D A
thb.ts040.005 85 80
thb.ts040.004 55 100
thb.ts040.006 55 130
TS 50 Artikelnummer aticle number
D A
thb.ts050.007 50 130
thb.ts050.003 50 200
thb.ts050.006 60 130
thb.ts050.002 63 200
thb.ts050.004 73 135
thb.ts050.005 75 260
TS 63 Artikelnummer aticle number
D A
thb.ts063.002 63 200
thb.ts063.005 80 100
thb.ts063.003 80 250
thb.ts063.004 109 134
TS 100 Artikelnummer aticle number
D A
thb.ts100.001 63 200
thb.ts100.002 80 250
thb.ts100.003 90 300
Wir führen auch weitere Lehren für Service und Wartung an Werkzeugmaschinen wie z.B.:
ClampControl zur elektronischen Messung von Einzugs– und Spannkräften sowie Einstell– und Ausrichtlehren für Maschinenspindeln, Werkzeugrevolver oder Werkzeugwechsler.
We also supply further gauges for service and maintenance of machine tools as there are: ClampControl for electronic measurement of pull back and clamping forces as well as setting and alignment gauges for machine spindles, tool turrets or tool changers.
JIS B 6339 Interface JIS B 6339 (before MAS 403 BT) Taper and gripper groove ground and hardened to 50 – 58 HRC Shaft part not hardened and easily machineable Material: 16MnCr5 Shaft part tempered to 600 - 800 Nm
MAS-BT 30 Artikelnummer aticle number
D A
thb.bt030.001 40,5 160
MAS-BT 40 Artikelnummer aticle number
D A
thb.bt040.001 40,5 100
thb.bt040.002 40,5 160
thb.bt040.003 50,5 100
thb.bt040.004 50,5 200
thb.bt040.005 63,5 160
thb.bt040.006 63,5 250
MAS-BT 50 Artikelnummer aticle number
D A
thb.bt050.001 40,5 100
thb.bt050.002 40,5 160
thb.bt050.003 50,5 100
thb.bt050.004 50,5 200
thb.bt050.005 63,5 200
thb.bt050.006 63,5 315
thb.bt050.007 95,5 200
thb.bt050.008 97 315
clever clamping
Thomas Esswein Römerweg 33 D-73642 Welzheim [email protected]
www.tessma.de
Morse Taper Interface
Morse taper DIN 228
TS-Interface (known as KM)
Applied for patent1987
Market introduction 1989 >KM<
Modular taper interface with ball
track system ISO 26622-1
HSK-Interface
Standard for rotating tool holders:
DIN 69893-1 Form A and C
ISO 12164-1 Style A and C
DIN 69893-6 Form F
Standard for lathe tool holders:
ISO 12164-3 Form T “Turning”
PSC-Interface (known as Capto)
Applied for patent 1988
Market introduction 1990 >Capto<
Polygonal taper interface with flange
surface contact
ISO 26623-1
Steep Taper (SK)-Interface
Steep taper for automated tool change
DIN 69871 part 1: Form A
JIS B 6339 (before MAS-BT)
ASME B5.50 (ANSI/CAT)
TH
B_01/1
5-1
-100
Top Related