U.S. Department East Building, PHH – 32
of Transportation 1200 New Jersey Avenue, Southeast
Washington, D.C. 20590
Pipeline and Hazardous The US Department of Transportation
Materials Safety Administration Competent Authority for the United States
Tracking No: 2019054336 Page 1 of 1
CLASSIFICATION OF EXPLOSIVES
FOURTH REVISION
Based upon a request by Owen Oil Tools c/o Owen Compliance Services, 12001 County
Road 1000, Godley, TX 76044, US, the following items are classed in accordance with
Section 173.56, Title 49, Code of Federal Regulations (49 CFR). A copy of your
application, all supporting documentation and a copy of this approval must be retained
and made available to DOT upon request.
An EX approval is non-transferable in any merger, acquisition, sale of assets, or other
business transaction. For more information, please visit:
[https://www.phmsa.dot.gov/registration/faq-mergers-acquisitions-and-legal-status-
changes-pdf]
U.N. PROPER SHIPPING NAME AND NUMBER:
Igniters, UN0454
U.N. CLASSIFICATION CODE: 1.4S
REFERENCE NUMBER: PRODUCT DESIGNATION/PART NUMBER:
EX2008120360 OOT-APRV-055 Igniter Family (D/N: OOT-
APRV-055A, Rev. 3): Type A (Power Charge
Igniters), Type B (Core Load Igniters), Type C
(Power Charge Igniters), Type D (Swing Jet
Release), Type E (Power Charge Igniters)
NOTES: This classification is only valid when the igniters are packaged as follows:
Inner Packaging - Boxes, chipboard, each containing one (1) igniter.
Outer Packaging - UN 4G fiberboard box, each containing not more than fifty (50) inner
packagings uniformly segregated from one another and the box sidewalls by not less than
three layers of corrugated fiberboard divider pieces and with top and bottom fiberboard
pads.
This approval as revised supersedes all previous versions.
DATED: July 10, 2019
for William Schoonover
Associate Administrator for Hazardous Materials Safety
A
A
B
B
C
C
D
D
PLUGIGNITION MIX
RESISTOR
LEAD WIRES
O-RING SEAL
PROPELLANTFFFFG BLACK POWDER
NEEDLE
RUBBER STOPPER BODY CAP
CRIMP CONNECTOR RESISTOR
EPOXYLEAD WIRE
END CAP & EPOXY
IGNITION HOUSING
SPRING HOUSING
CONTACT PIN
TOP INSULATOR
SPRINGRESISTOR
HEAT SHRINK
IGNITION MIXTEFLON TUBING
INSULATING WASHER
END CAP & EPOXY
IGNITION MIXRESISTORPLASTIC INSULATOR
SPRING CONTACT
GROUND WIRE
BODY
TYPE C, Power Charge Igniter≤ 2.8
≤ 2.8
≤ 3.3
0.05g BP OR 0.05g BKNO3 (50/50 OR 25/75 MIXTURE) OR
0.05g BP & TSPP
TYPE A, Power Charge Igniter≤ 2.8
≤ 2.8
≤ 3.3
0.05g BP OR 0.05g BKNO3 (50/50 OR 25/75 MIXTURE) OR
0.05g BP & TSPP
TYPE B, Core Load Igniter≤ 0.6 0.05g BP & #800 propellant
TYPE D, Swing Jet Release≤ 0.26 0.05g BP
NOTES:BP = Black PowderBKNO3 = Boron Potassium Nitrate TSPP = Titanium Sub-Hydride Potassium Perchlorate
* SEE SHEET 2 OF 2 FORTYPE E, POWER CHARGE IGNITER
03 ADDED OPTION E (PAGE 2 OF 2) 2/25/2019 RS
02 ADDED BKNO3 OPTION TO TYPE A & C 3/2/2015 BP
01 ADDED TYPE D 8/2/2013 DWBREV DESCRIPTION DATE (M/D/Y) INITIAL
Packaging, Marking, and Labeling
Packaging: As shown in drawing OOT-APRV-055B
Marking: Igniters, UN0454
Hazard Label: 1.4S
Consult OCS for any variations
TITLE:
PART / DRAWING: REV.
DESIGNED:
DATE (M/D/Y):
DATE (M/D/Y):
MATERIAL:
HEAT TREATMENT:
TOLERANCES UNLESS OTHERWISE NOTED: OWEN OIL TOOLS LPA CORE LABORATORIES COMPANY12001 COUNTY ROAD 1000GODLEY, TEXAS 76044
OWEN OIL TOOLS, CANADIAN DIVISIONA DIVISION OF CORE LABORATORIESCANADA LTD.5405-39139 HWY. 2ARED DEER, COUNTYALBERTA, CANADA, T4S 2B3
DRAFTED:
DO NOT SCALE DRAWING SHEET 1 OF 2
PROTECTIVE FINISH:
2/25/2019
N/AN/A
R. SEARLES
ALL DIMENSIONS IN INCHESBREAK EDGES 0.015 X 45CONCENTRICITY 0.005 TIRMAX SURFACE FINISH 125 RMS ANGULAR DIMENSIONS 0.5MIN RADIUS 0.010
.X = 0.030
.XX = 0.015.XXX = 0.005
OES-1000-100TRACEABILITY:
03
THIS TECHNOLOGY IS REGULATED BY AND, IF EXPORTED, WAS EXPORTED FROM THE UNITED STATES IN ACCORDANCE WITH THE EXPORT
ADMINISTRATION REGULATIONS (EAR). DIVERSION CONTRARY TO U.S. LAW IS PROHIBITED. EXPORT AND/OR RE-EXPORT OF THIS TECHNOLOGY MAY
REQUIRE ISSUANCE OF A LICENSE BY THE BUREAU OF INDUSTRY AND SECURITY (BIS), U.S. DEPARTMENT OF COMMERCE. CONSULT THE BIS, THE
EAR, AND/OR OWEN COMPLIANCE SERVICES, INC. TO DETERMINE LICENSING REQUIREMENTS FOR EXPORT OR RE-EXPORT OF THIS TECHNOLOGY.
NOTICE: EXPORT OF TECHNOLOGYTHIS DRAWING AND ACCOMPANYING INFORMATION IS THE
CONFIDENTIAL PROPERTY OF OWEN OIL TOOLS AND MAY NOT BE COPIED, REPRODUCED, TRANSMITTED OR DISCLOSED IN ANY
MANNER WITHOUT EXPRESS WRITTEN CONSENT AND IS TO BE RETURNED UPON REQUEST. ALL RIGHTS IN PROPRIETARY,
COPYRIGHT AND NOVEL FEATURES OF THE SUBJECT MATTERARE EXPRESSLY RESERVED. RECIPIENTS AGREEMENT TO THE
FOREGOING IS INDICATED BY ACCEPTANCE OF THIS DOCUMENT.
NOTICE: PROPRIETARY RIGHTS INVOLVED
OEF-4010-001 (R00)
OWEN OIL TOOLSOOT-APRV-055IGNITER FAMILY
N/A
OOT-APRV-055A
EE
GROUND WIRE
SPRING CONTACT
INSULATOR MOLDING GROUNDING SLEEVERESISTOR
RESISTOR IGNITION MIX
END SEAL & ADHESIVE
BRIDGEWIRE
BODY
INSULATOR
TYPE E, Power Charge Igniter≤ 2.0
≤ 2.0
≤ 2.4
0.05g BP OR 0.05g BKNO3 (50/50 OR 25/75 MIXTURE) OR
0.05g BP & TSPP
DESCRIPTION:
PART / DRAWING: REV.
DESIGNED:
DATE (M/D/Y):
DATE (M/D/Y):
MATERIAL:
HEAT TREATMENT:
TOLERANCES UNLESS OTHERWISE NOTED: OWEN OIL TOOLS LPA CORE LABORATORIES COMPANY12001 COUNTY ROAD 1000GODLEY, TEXAS 76044
OWEN OIL TOOLS, CANADIAN DIVISIONA DIVISION OF CORE LABORATORIESCANADA LTD.5405-39139 HWY. 2ARED DEER, COUNTYALBERTA, CANADA, T4S 2B3
DRAFTED:
DO NOT SCALE DRAWING SHEET 2 OF 2
PROTECTIVE FINISH:
2/26/2019R. SEARLES
ALL DIMENSIONS IN INCHESBREAK EDGES 0.015 X 45CONCENTRICITY 0.005 TIRMAX SURFACE FINISH 125 RMS ANGULAR DIMENSIONS 0.5MIN RADIUS 0.010
.X = 0.030
.XX = 0.015.XXX = 0.005
OES-1000-100TRACEABILITY:
03
THIS TECHNOLOGY IS REGULATED BY AND, IF EXPORTED, WAS EXPORTED FROM THE UNITED STATES IN ACCORDANCE WITH THE EXPORT
ADMINISTRATION REGULATIONS (EAR). DIVERSION CONTRARY TO U.S. LAW IS PROHIBITED. EXPORT AND/OR RE-EXPORT OF THIS TECHNOLOGY MAY
REQUIRE ISSUANCE OF A LICENSE BY THE BUREAU OF INDUSTRY AND SECURITY (BIS), U.S. DEPARTMENT OF COMMERCE. CONSULT THE BIS, THE
EAR, AND/OR OWEN COMPLIANCE SERVICES, INC. TO DETERMINE LICENSING REQUIREMENTS FOR EXPORT OR RE-EXPORT OF THIS TECHNOLOGY.
NOTICE: EXPORT OF TECHNOLOGYTHIS DRAWING AND ACCOMPANYING INFORMATION IS THE
CONFIDENTIAL PROPERTY OF OWEN OIL TOOLS AND MAY NOT BE COPIED, REPRODUCED, TRANSMITTED OR DISCLOSED IN ANY
MANNER WITHOUT EXPRESS WRITTEN CONSENT AND IS TO BE RETURNED UPON REQUEST. ALL RIGHTS IN PROPRIETARY,
COPYRIGHT AND NOVEL FEATURES OF THE SUBJECT MATTERARE EXPRESSLY RESERVED. RECIPIENTS AGREEMENT TO THE
FOREGOING IS INDICATED BY ACCEPTANCE OF THIS DOCUMENT.
NOTICE: PROPRIETARY RIGHTS INVOLVED
OEF-4010-001 (R00)
TOOL:
OOT-APRV-055A
U.S. Department East Building, PHH – 32
of Transportation 1200 New Jersey Avenue, Southeast
Washington, D.C. 20590
Pipeline and Hazardous The US Department of Transportation
Materials Safety Administration Competent Authority for the United States
Tracking No: 2019054336 Page 1 of 1
CLASSIFICATION OF EXPLOSIVES
FOURTH REVISION
Based upon a request by Owen Oil Tools c/o Owen Compliance Services, 12001 County
Road 1000, Godley, TX 76044, US, the following items are classed in accordance with
Section 173.56, Title 49, Code of Federal Regulations (49 CFR). A copy of your
application, all supporting documentation and a copy of this approval must be retained
and made available to DOT upon request.
An EX approval is non-transferable in any merger, acquisition, sale of assets, or other
business transaction. For more information, please visit:
[https://www.phmsa.dot.gov/registration/faq-mergers-acquisitions-and-legal-status-
changes-pdf]
U.N. PROPER SHIPPING NAME AND NUMBER:
Igniters, UN0454
U.N. CLASSIFICATION CODE: 1.4S
REFERENCE NUMBER: PRODUCT DESIGNATION/PART NUMBER:
EX2008120360 OOT-APRV-055 Igniter Family (D/N: OOT-
APRV-055A, Rev. 3): Type A (Power Charge
Igniters), Type B (Core Load Igniters), Type C
(Power Charge Igniters), Type D (Swing Jet
Release), Type E (Power Charge Igniters)
NOTES: This classification is only valid when the igniters are packaged as follows:
Inner Packaging - Boxes, chipboard, each containing one (1) igniter.
Outer Packaging - UN 4G fiberboard box, each containing not more than fifty (50) inner
packagings uniformly segregated from one another and the box sidewalls by not less than
three layers of corrugated fiberboard divider pieces and with top and bottom fiberboard
pads.
This approval as revised supersedes all previous versions.
DATED: July 10, 2019
for William Schoonover
Associate Administrator for Hazardous Materials Safety
U.S. Department East Building, PHH – 32
of Transportation 1200 New Jersey Avenue, Southeast
Washington, D.C. 20590
Pipeline and Hazardous The US Department of Transportation
Materials Safety Administration Competent Authority for the United States
CLASSIFICATION OF EXPLOSIVES
Tracking No: 2015031101 Page 1 of 1
THIRD REVISION
Based upon a request by Owen Oil Tools c/o Owen Compliance Services, P.O. Box 765,
Godley, TX 76044, United States, the following items are classed in accordance with
Section 173.56, Title 49, Code of Federal Regulations (49 CFR). A copy of your
application, all supporting documentation and a copy of this approval must be retained
and made available to DOT upon request.
U.N. PROPER SHIPPING NAME AND NUMBER:
Igniters, UN0454
U.N. CLASSIFICATION CODE: 1.4S
REFERENCE NUMBER PRODUCT DESIGNATION/PART NUMBER
EX2008120360 OOT-APRV-055 Igniter Family (D/N: OOT-
APRV-055A, Rev. 2): Type A (Power
Charge Igniters), Type B (Core Load Igniters),
Type C (Power Charge Igniters), Type D (Swing Jet
Release)
NOTES: This classification is only valid when the igniters are packaged as follows:
Inner Packaging - Boxes, chipboard, each containing one (1) igniter. Outer Packaging -
UN4G fiberboard box, each containing not more than fifty (50) inner packagings
uniformly segregated from one another and the box sidewalls by not less than three layers
of corrugated fiberboard divider pieces and with top and bottom fiberboard pads.
This approval as revised supersedes all previous versions.
DATED: 09/16/2015
For Dr. Magdy El-Sibaie
Associate Administrator for Hazardous Materials Safety
This page is intentionally blank to facilitate 2-sided printing
A
A
B
B
C
C
D
D
PLUGIGNITION MIX
RESISTOR
LEAD WIRES
O-RING SEAL
PROPELLANTFFFFG BLACK POWDER
NEEDLE
RUBBER STOPPER BODY CAP
CRIMP CONNECTOR RESISTOR
EPOXYLEAD WIRE
END CAP & EPOXY
IGNITION HOUSING
SPRING HOUSING
CONTACT PIN
TOP INSULATOR
SPRINGRESISTOR
HEAT SHRINK
IGNITION MIXTEFLON TUBING
INSULATING WASHER
END CAP & EPOXY
IGNITION MIXRESISTORPLASTIC INSULATOR
SPRING CONTACT
GROUND WIRE
BODY
TYPE C, Power Charge Igniter≤ 2.8 0.05g BP
OR≤ 2.8 0.05g BKNO3 (50/50 OR 25/75 MIXTURE)
OR≤ 3.3 0.05g BP & TSPP
TYPE A, Power Charge Igniter≤ 2.8 0.05g BP
OR≤ 2.8 0.05g BKNO3 (50/50 OR 25/75 MIXTURE)
OR≤ 3.3 0.05g BP & TSPP
TYPE B, Core Load Igniter≤ 0.6 0.05g BP & #800 propellant
TYPE D, Swing Jet Release≤ 0.26 0.05g BP
NOTES:BP = Black PowderBKNO3 = Boron Potassium NitrateTSPP = Titanium Sub-Hydride Potassium Perchlorate
02 ADDED BKNO3 OPTION TO TYPE A & C 3/2/2015 BP
01 ADDED TYPE D 8/2/2013 DWBREV DESCRIPTION DATE (M/D/Y) INITIAL
Packaging, Marking, and Labeling
Packaging: As shown in drawing OOT-APRV-055B
Marking: Igniters, UN0454
Hazard Label: 1.4S
Consult OCS for any variations
TITLE:
PART / DRAWING: REV.
DESIGNED:
DATE (M/D/Y):
DATE (M/D/Y):
MATERIAL:
HEAT TREATMENT:
TOLERANCES UNLESS OTHERWISE NOTED: OWEN OIL TOOLS LPA CORE LABORATORIES COMPANY12001 COUNTY ROAD 1000GODLEY, TEXAS 76044
OWEN OIL TOOLS, CANADIAN DIVISIONA DIVISION OF CORE LABORATORIESCANADA LTD.5405-39139 HWY. 2ARED DEER, COUNTYALBERTA, CANADA, T4S 2B3
DRAFTED:
DO NOT SCALE DRAWING SHEET 1 OF 1
PROTECTIVE FINISH:
3/2/2015
N/AN/A
B. POTTER
ALL DIMENSIONS IN INCHESBREAK EDGES 0.015 X 45CONCENTRICITY 0.005 TIRMAX SURFACE FINISH 125 RMS ANGULAR DIMENSIONS 0.5MIN RADIUS 0.010
.X = 0.030
.XX = 0.015.XXX = 0.005
OES-1000-100TRACEABILITY:
02
THIS TECHNOLOGY IS REGULATED BY AND, IF EXPORTED, WAS EXPORTED FROM THE UNITED STATES IN ACCORDANCE WITH THE EXPORT
ADMINISTRATION REGULATIONS (EAR). DIVERSION CONTRARY TO U.S. LAW IS PROHIBITED. EXPORT AND/OR RE-EXPORT OF THIS TECHNOLOGY MAY
REQUIRE ISSUANCE OF A LICENSE BY THE BUREAU OF INDUSTRY AND SECURITY (BIS), U.S. DEPARTMENT OF COMMERCE. CONSULT THE BIS, THE
EAR, AND/OR OWEN COMPLIANCE SERVICES, INC. TO DETERMINE LICENSING REQUIREMENTS FOR EXPORT OR RE-EXPORT OF THIS TECHNOLOGY.
NOTICE: EXPORT OF TECHNOLOGYTHIS DRAWING AND ACCOMPANYING INFORMATION IS THE
CONFIDENTIAL PROPERTY OF OWEN OIL TOOLS AND MAY NOT BE COPIED, REPRODUCED, TRANSMITTED OR DISCLOSED IN ANY
MANNER WITHOUT EXPRESS WRITTEN CONSENT AND IS TO BE RETURNED UPON REQUEST. ALL RIGHTS IN PROPRIETARY,
COPYRIGHT AND NOVEL FEATURES OF THE SUBJECT MATTERARE EXPRESSLY RESERVED. RECIPIENTS AGREEMENT TO THE
FOREGOING IS INDICATED BY ACCEPTANCE OF THIS DOCUMENT.
NOTICE: PROPRIETARY RIGHTS INVOLVED
OEF-4010-001 (R00)
OWEN OIL TOOLSOOT-APRV-055IGNITER FAMILY
N/A
OOT-APRV-055A
U.S. Department East Building, PHH – 32
of Transportation 1200 New Jersey Avenue, Southeast
Washington, D.C. 20590
Pipeline and Hazardous The US Department of Transportation
Materials Safety Administration Competent Authority for the United States
CLASSIFICATION OF EXPLOSIVES
Tracking No: 2013121575 Page 1 of 1
SECOND REVISION
Based upon a request by Owen Oil Tools c/o Owen Compliance Services, P.O. Box 765,
Godley, TX 76044, United States the following items are classed in accordance with
Section 173.56, Title 49, Code of Federal Regulations (49 CFR). A copy of your
application, all supporting documentation and a copy of this approval must be retained
and made available to DOT upon request.
U.N. PROPER SHIPPING NAME AND NUMBER:
Igniters, UN0454
U.N. CLASSIFICATION CODE: 1.4S
REFERENCE NUMBER PRODUCT DESIGNATION/PART NUMBER
EX2008120360 OOT-APRV-055 Igniter Family: Type A (Power
Charge Igniters), Type B (Core Load Igniters),
Type C (Power Charge Igniters), Type D (Swing Jet
Release)
NOTES: This classification is only valid when the igniters are packaged as follows:
Inner Packaging - Boxes, chipboard, each containing one (1) igniter. Outer Packaging -
UN4G fiberboard box, each containing not more than fifty (50) inner packagings
uniformly segregated from one another and the box sidewalls by not less than three layers
of corrugated fiberboard divider pieces and with top and bottom fiberboard pads.
This approval as revised supersedes all previous versions.
DATED: 04/30/2014
For Dr. Magdy El-Sibaie
Associate Administrator for Hazardous Materials Safety
U.S. Department East Building, PHH – 32
of Transportation 1200 New Jersey Avenue, Southeast
Washington, D.C. 20590
Pipeline and Hazardous The US Department of Transportation
Materials Safety Administration Competent Authority for the United States
CLASSIFICATION OF EXPLOSIVES
Tracking No: 2011070680 Page 1 of 1
FIRST REVISION
Based upon a request by Owen Oil Tools, P.O. Box 765, Godley, TX 76044, United
States the following items are classed in accordance with Section 173.56, Title 49, Code
of Federal Regulations (49 CFR). A copy of your application, all supporting
documentation and a copy of this approval must be retained and made available to DOT
upon request.
U.N. PROPER SHIPPING NAME AND NUMBER:
Igniters, UN0454
U.N. CLASSIFICATION CODE: 1.4S
REFERENCE NUMBER PRODUCT DESIGNATION/PART NUMBER
EX2008120360 OOT-APRV-055 Owen Oil Tools Igniter Family:
Type A (Power Charge Igniters), Type B (Core
Load Igniters), Type C (Power Charge Igniters)
NOTES: This classification is only valid when the igniters are packaged as follows:
Inner Packaging - Boxes, chipboard, each containing one igniter. Outer Packaging - UN
4G fiberboard box, each containing not more than fifty (50) inner packagings uniformly
segregated from one another and the box sidewalls by not less than three layers of
corrugated fiberboard divider pieces and with top and bottom fiberboard pads. This
approval as revised supersedes all previous versions.
DATED: 09/22/2011
For Dr. Magdy El-Sibaie
Associate Administrator for Hazardous Materials Safety
U.S. Department East Building, PHH – 32
of Transportation 1200 New Jersey Avenue, Southeast
Washington, D.C. 20590
Pipeline and Hazardous The US Department of Transportation
Materials Safety Administration Competent Authority for the United States
CLASSIFICATION OF EXPLOSIVES
Tracking No: 2008120517 Page 1 of 1
Based upon a request by Owen Oil Tools, P.O. Box 765, 12001 County Road 1000,
Godley, TX 76044, the following items are classed in accordance with Section 173.56,
Title 49, Code of Federal Regulations (49 CFR). A copy of the application, all
supporting documentation, and a copy of this Classification must be retained and made
available to DOT upon request.
U.N. PROPER SHIPPING NAME AND NUMBER:
Igniters, UN0454
U.N. CLASSIFICATION CODE: 1.4S
REFERENCE NUMBER PRODUCT DESIGNATION/PART NUMBER
EX2008120360 OOT-APRV 055A Owen Oil Tools Igniter Family:
Type A (Power Charge Igniters), Type B (Core
Load Igniters), Type C (Power Charge Igniters)
NOTES: This classification is only valid when the igniters are packaged as follows:
Inner Packaging - Boxes, chipboard, each containing one igniter. Outer Packaging - UN
4G fiberboard box, each containing not more than fifty (50) inner packagings uniformly
segregated from one another and the box sidewalls by not less that three layers of
corrugated fiberboard divider pieces and with top and bottom fiberboard pads.
DATED: 04/01/2009
For Theodore L. Willke
Associate Administrator for Hazardous Materials Safety
Top Related