Black Cat Blades Ltd. Teeth
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
J200 TEETH Serial Number:1U3202 TOOTH 2.80 1.27Standard Long Tooth
1U3209 TOOTH 2.40 1.09Penetration Tooth
1099200 TOOTH 3.50 1.59Flare Tooth
J200TIGER TOOTH 3.20 1.45Tiger Tooth
J200TWIN TOOTH 3.80 1.72Twin Tiger Tooth
1U3201 TOOTH 2.65 1.202.438 x 2.250 x 5.250Short Tooth
1193204 ADP 4.40 2.00Two Strap Adapter
1193205 ADP 4.85 2.20Two Strap Adapter
4T1204 ADP 4.85 2.202.476 x 1.809 x 9.362Top Strap Adapter
8J7525 ADP 3.30 1.502.063 x 1.625 x 6.874Bottom Strap Adapter
8E2184 ADP 2 2.21 2.95 5.30 2.402.500 x 2.375 x 8.915Bolt-On Center Adapter 0.625
J200WN NOSE 1 2.10 0.952.313 x 2.250 x 3.594Weld on Nose
9W7112 PIN 0.10 0.05Standard Groove Pin
4T0001 RET 0.02 0.01Standard Retainer
8E6208 PIN 0.10 0.05Radius Groove Pin
8E6209 RET 0.04 0.02Retainer with Plastic Holder
J225 TEETH Serial Number:6Y3222 TOOTH 4.50 2.04Standard Long Tooth
6Y6221 TOOTH 3.90 1.77Short Tooth
8E4222 TOOTH 5.80 2.63Heavy Duty Long Tooth
6Y8229 TOOTH 4.60 2.09Penetration Tooth
1863010 TOOTH 6.60 2.99Flare Tooth
J225TIGER TOOTH 4.70 2.13Tiger Tooth
J225TWIN TOOTH 5.00 2.27Twin Tiger Tooth
J225HDAL TOOTH 6.60 2.99Heavy Duty Abrasion Tooth
6Y3224 ADP 6.80 3.08Two Strap Adapter
J225WN NOSE 3.80 1.72Weld on Nose
6Y3228 PIN 0.10 0.05Standard Groove Pin
3G9609 RET 0.06 0.03Standard Retainer
8E6259 RET 0.08 0.04Retainer with Plastic Holder
1324762 PIN 0.20 0.09Heavy Duty Pin
1495733 RET 0.04 0.02Heavy Duty Coiled Retainer
J250 TEETH Serial Number:1U3252 TOOTH 6.20 2.81Standard Long Tooth
1U3251 TOOTH 5.60 2.54Short Tooth
9N4252 TOOTH 7.70 3.49Heavy Duty Long Tooth
1358252 TOOTH 11.00 4.99Heavy Duty Long Tooth C/IMP
9J4259 TOOTH 6.40 2.90Penetration Tooth
2085254 TOOTH 8.80 3.99Flare Tooth
J250TIGER TOOTH 6.30 2.86Tiger Tooth
J250TWIN TOOTH 6.20 2.81Twin Tiger Tooth
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Teeth
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
J250PP TOOTH 10.20 4.633.813 x 3.313 x 8.750Penetration Plus Tooth
J250L TOOTH 7.05 3.203.395 x 3.049 x 8.076L Style Tooth
J250HP TOOTH 15.70 7.123.841 x 3.313 x 9.688Hevy Duty Penetration Tooth
J250HDAL TOOTH 9.60 4.35Heavy Duty Abrasion Tooth
1193253 ADP 11.50 5.22Two Strap Adapter
1U1254 ADP 12.13 5.50Top Strap Adapter
1U0257 ADP 2 4.88 22.70 10.3024.135 x 3.248 x 14.267Bolt-On Center Adapter 1.000 x 3.75
6I9250 ADP 2Bolt-On Corner Adapter LH 34.30 15.561.500 x 10.574 x 13.337
6I9251 ADP 2Bolt-On Corner Adapter RH 34.30 15.561.500 x 10.574 x 13.329
J250WN NOSE 5.00 2.27Weld on Nose
9J2258 PIN 0.22 0.10Standard Groove Pin
3G9609 RET 0.06 0.03Standard Retainer
8E6258 PIN 0.22 0.10Radius Groove Pin
8E6259 RET 0.08 0.04Retainer with Plastic Holder
1324763 PIN 0.22 0.10Heavy Duty Pin
1495733 RET 0.04 0.02Heavy Duty Coiled Retainer
J300 TEETH Serial Number:1U3302 TOOTH 9.70 4.40Standard Long Tooth
1U3301 TOOTH 9.00 4.08Short Tooth
9N4302 TOOTH 12.90 5.85Heavy Duty Long Tooth
1258302 TOOTH 14.60 6.62Heavy Duty Long Tooth C/IMP
9J4309 TOOTH 9.00 4.08Penetration Tooth
1258309 TOOTH 9.30 4.22Penetration Tooth C/IMP
1073300 TOOTH 13.20 5.99Flare Tooth
J300TIGER TOOTH 10.30 4.67Tiger Tooth
J300TWIN TOOTH 12.40 5.62Twin Tiger Tooth
1835300 TOOTH 12.50 5.67Penetration Plus Tooth
J300L TOOTH 11.02 5.003.830 x 3.613 x 8.950L Style Tooth
1359300 TOOTH 18.60 8.44Hevy Duty Penetration Tooth
J300HDAL TOOTH 16.20 7.35Heavy Duty Abrasion Tooth
J300RC TOOTH 13.00 5.90Rock Chisel Tooth
3G6304 ADP 17.90 8.12Two Strap Adapter
3G6305 17.20 7.80Two Strap Adapter RH
3G6306 17.20 7.80Two Strap Adapter LH
8E9490 ADP 16.60 7.53Two Strap Adapter
1U1304 ADP 21.16 9.60Top Strap Adapter
1U0307 ADP 2 4.88 29.70 13.4724.497 x 4.000 x 14.416Bolt-On Center Adapter 1.000 x 3.75
3G9307 ADP 2 6.31 35.40 16.064.723 x 4.621 x 16.000Bolt-On Center Adapter 1.250
4T4307 ADP 2 6.50 32.60 14.7924.691 x 4.249 x 15.196Bolt-On Center Adapter 1.000 x 4
8E5308 ADP 2Bolt-On Corner Adapter LH 44.50 20.182.000 x 10.519 x 14.066
8E5309 ADP 2Bolt-On Corner Adapter RH 44.50 20.182.000 x 10.519 x 14.066
J300WN NOSE 7.40 3.363.500 x 3.500 x Weld on Nose
1U0307 ADP 2 4.88 29.70 13.4724.497 x 4.000 x 14.416Bolt-On Center Adapter 1.000 x 3.75
3G9307 ADP 2 6.31 35.40 16.064.723 x 4.621 x 16.000Bolt-On Center Adapter 1.250
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Teeth
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T4307 ADP 2 6.50 32.60 14.7924.691 x 4.249 x 15.196Bolt-On Center Adapter 1.000 x 4
9J2308 PIN 0.24 0.11Standard Groove Pin
3G9609 RET 0.06 0.03Standard Retainer
1073308 PIN 0.24 0.11Radius Groove Pin
8E6259 RET 0.08 0.04Retainer with Plastic Holder
1324766 PIN 0.24 0.11Heavy Duty Pin
1495733 RET 0.04 0.02Heavy Duty Coiled Retainer
J350 TEETH Serial Number:1U3352 TOOTH 12.90 5.85Standard Long Tooth
1U3351 TOOTH 12.80 5.81Short Tooth
9N4352 TOOTH 17.60 7.98Heavy Duty Long Tooth
1359352 TOOTH 21.30 9.66Heavy Duty Long Tooth C/IMP
9J4359 TOOTH 12.70 5.76Penetration Tooth
1199359 TOOTH 12.80 5.81Penetration Tooth C/IMP
1073350 TOOTH 19.80 8.98Flare Tooth
J350TIGER TOOTH 14.30 6.49Tiger Tooth
J350TWIN TOOTH 15.70 7.12Twin Tiger Tooth
J350TTD TOOTH 15.00 6.804.467 x 5.193 x 11.250Twin Tiger Tooth
1681359 TOOTH 16.00 7.26Penetration Plus Tooth
J350L TOOTH 14.55 6.604.390 x 4.151 x 10.441L Style Tooth
1441358 TOOTH 25.90 11.75Hevy Duty Penetration Tooth
J350HDAL TOOTH 22.50 10.21Heavy Duty Abrasion Tooth
J350RC TOOTH 17.90 8.12Rock Chisel Tooth
6I6354 ADP 26.00 11.79Two Strap Adapter
3G8354 ADP 19.70 8.94Two Strap Adapter
1U1354 ADP 33.07 15.004.375 x 3.438 x 16.897Two Strap Adapter
1U1355 ADP 30.10 13.654.375 x 3.438 x 16.897Two Strap Adapter LH
1U1356 ADP 30.10 13.654.375 x 3.438 x 16.897Two Strap Adapter RH
J350WN NOSE 10.20 4.634.375 x 4.000 x Weld on Nose
3G3357 ADP 2J350 Bolt-On Center Adapter 45.20 20.505.317 x 4.998 x 16.625
1U1357 ADP 2J350 Bolt-On Center Adapter 45.90 20.825.275 x 4.997 x 17.342
9W2678 PIN 1.00 0.45Standard Groove Pin
3G9549 PIN 0.07 0.03Standard Retainer
8E6358 PIN 0.53 0.24Radius Groove Pin
8E6359 RET 0.12 0.05Retainer with Plastic Holder
1140358 PIN 0.53 0.24Heavy Duty Pin
1140359 RET 0.06 0.03Heavy Duty Coiled Retainer
J400 TEETH Serial Number:7T3402 TOOTH 20.80 9.43Standard Long Tooth
7T3401 TOOTH 18.90 8.57Short Tooth
8E4402 TOOTH 25.40 11.52Heavy Duty Long Tooth
1167402 TOOTH 29.90 13.56Heavy Duty Long Tooth C/IMP
6Y7409 TOOTH 20.30 9.21Penetration Tooth
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 3©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Teeth
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1247409 TOOTH 21.80 9.89Penetration Tooth C/IMP
1073400 TOOTH 28.10 12.75Flare Tooth
J400TIGER TOOTH 23.00 10.43Tiger Tooth
J400TWIN TOOTH 26.20 11.88Twin Tiger Tooth
1681409 TOOTH 26.00 11.79Penetration Plus Tooth
J400L TOOTH 22.49 10.204.820 x 4.865 x 11.463L Style Tooth
1359400 TOOTH 32.80 14.88Hevy Duty Penetration Tooth
J400HDAL TOOTH 31.80 14.42Heavy Duty Abrasion Tooth
J400RC TOOTH 26.20 11.88Rock Chisel Tooth
6I6404 ADP 35.00 15.88Two Strap Adapter
6I6404-16 ADP 36.20 16.42Two Strap Adapter
J400WN NOSE 15.00 6.805.000 x 4.625 x Weld on Nose
6I9898 ADP 2J400 Bolt-On Center Adapter 60.60 27.496.688 x 5.188 x 17.354
7T3408 PIN 0.78 0.35Standard Groove Pin
7T3409 RET 0.11 0.05Standard Retainer
8E8409 RET 0.13 0.06Retainer with Plastic Holder
1167408 PIN 0.78 0.35Heavy Duty Pin
1167409 RET 0.07 0.03Heavy Duty Coiled Retainer
J450/460 TEETH Serial Number:9W8452 TOOTH 25.60 11.61Standard Long Tooth
9W8451 TOOTH 23.60 10.70Short Tooth
9N4452 TOOTH 35.90 16.28Heavy Duty Long Tooth
1019054 TOOTH 1 3.35 42.00 19.05Heavy Duty Long Tooth C/IMP
9W8459 TOOTH 21.80 9.89Penetration Tooth
1167459 TOOTH 23.60 10.70Penetration Tooth C/IMP
1073450 TOOTH 36.40 16.51Flare Tooth
J450TIGER TOOTH 29.40 13.34Tiger Tooth
J450TWIN TOOTH 31.60 14.33Twin Tiger Tooth
J450TTD TOOTH 32.00 14.515.467 x 6.768 x 14.063Twin Tiger Tooth
1590459 TOOTH 33.50 15.20Penetration Plus Tooth
J450L TOOTH 29.32 13.305.209 x 5.267 x 12.386L Style Tooth
1386451 TOOTH 45.20 20.50Hevy Duty Penetration Tooth
J450HDAL TOOTH 48.90 22.18Heavy Duty Abrasion Tooth
J450RC TOOTH 31.40 14.24Rock Chisel Tooth
1590464 ADP 48.20 21.86Two Strap Adapter J460 2.00 LIP
8E6464 ADP 44.40 20.145.722 x 4.863 x 17.059Two Strap Adapter J460 2.00 LIP
1590464-20 ADP 50.90 23.09Two Strap Adapter J460 2.50 LIP
1590464SL ADP 48.50 22.006.138 x 4.863 x 16.943Two Strap Adapter Solid Bottom Leg
8E0464 ADP 54.90 24.905.500 x 4.500 x 19.065Top Strap Adapter
J460WN NOSE 19.20 8.715.125 x 5.000 x Weld on Nose
8E0468 PIN 1.01 0.46Standard Groove Pin
8E0469 RET 1.00 0.45Standard Retainer
1140468 PIN 1.01 0.46Heavy Duty Pin
1073469 RET 0.08 0.04Heavy Duty Coiled Retainer
J550 TEETH Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 4©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Teeth
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W8552 TOOTH 40.80 18.51Standard Long Tooth
9W8551 TOOTH 32.80 14.88Short Tooth
9N4552 TOOTH 59.90 27.17Heavy Duty Long Tooth
1019055 TOOTH 61.70 27.99Heavy Duty Long Tooth C/IMP
9W8559 TOOTH 35.30 16.01Penetration Tooth
1130559 TOOTH 37.50 17.01Penetration Tooth C/IMP
1073550 TOOTH 58.30 26.44Flare Tooth
J550TIGER TOOTH 35.90 16.28Tiger Tooth
J550TWIN TOOTH 41.10 18.64Twin Tiger Tooth
1590559 TOOTH 53.20 24.13Penetration Plus Tooth
1386552 TOOTH 68.10 30.89Hevy Duty Penetration Tooth
J550HDAL TOOTH 73.90 33.52Heavy Duty Abrasion Tooth
J550RC TOOTH 49.70 22.54Rock Chisel Tooth
6I6554 ADP 79.20 35.92Two Strap Adapter J550 2.50 LIP
6I6554-24 ADP 80.00 36.29Two Strap Adapter J550 3.00 LIP
6I6554SL ADP 82.70 37.517.493 x 5.601 x 19.825Two Strap Adapter Solid Bottom Leg
J550WN NOSE 29.00 13.155.500 x 5.750 x Weld on Nose
1U1558 PIN 1.42 0.64Standard Groove Pin
3G9559 RET 0.15 0.07Standard Retainer
6Y8558 PIN 1.42 0.64Radius Groove Pin
8E5559 PIN 0.17 0.08Retainer with Plastic Holder
1073378 PIN 1.42 0.64Heavy Duty Pin
1078559 RET 0.09 0.04Heavy Duty Coiled Retainer
J600 TEETH Serial Number:6I6602 TOOTH 77.30 35.06Standard Long Tooth
7Y0602 TOOTH 101.10 45.867.500 x 7.625 x 16.300Heavy Duty Long Tooth
1078602 TOOTH 110.50 50.12Heavy Duty Long Tooth C/IMP
7I7609 TOOTH 61.70 27.99Penetration Tooth
1199609 TOOTH 66.40 30.12Penetration Tooth C/IMP
J600VX TOOTH 75.40 34.207.631 x 7.730 x 18.250Penetration Tooth
J600TIGER TOOTH 78.60 35.65Tiger Tooth
J600TWIN TOOTH 85.10 38.60Twin Tiger Tooth
1590607 TOOTH 84.90 38.51Penetration Plus Tooth
1359600 TOOTH 130.00 58.97Hevy Duty Penetration Tooth
J600HDAL TOOTH 129.80 58.88Heavy Duty Abrasion Tooth
J600RC TOOTH 85.50 38.78Rock Chisel Tooth
6I6604 ADPJ600 Weld-On Center Adapter 112.40 50.988.101 x 6.319 x 22.034
6I6604LH ADPJ600 Weld-On LH SPADE Adapter 117.90 53.488.412 x 6.321 x 23.023
6I6604RH ADPJ600 Weld-On RH SPADE Adapter 117.90 53.488.412 x 6.321 x 23.023
J600WN NOSE 55.90 25.367.125 x 7.625 x Weld on Nose
6I6608 PIN 2.30 1.04Standard Groove Pin
6I6609 RET 0.21 0.10Standard Retainer
1139608 PIN 2.30 1.04Heavy Duty Pin
1139609 RET 0.01 0.00Heavy Duty Coiled Retainer
J700 TEETH Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 5©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Teeth
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T4702 TOOTH 97.30 44.138.315 x 7.815 x 16.500Standard Long Tooth
J700VX TOOTH 87.70 39.788.145 x 7.984 x 19.500Penetration Tooth
1711709 TOOTH 110.10 49.948.000 x 8.165 x 18.688Penetration Plus Tooth
1359700 TOOTH 147.90 67.09Hevy Duty Penetration Tooth
J700HDAL TOOTH 154.20 69.948.635 x 8.500 x 19.000Heavy Duty Abrasion Tooth
1330704 ADP 149.69 67.908.965 x 7.480 x 23.154Two Strap Adapter J700 2.75 LIP
1330705 ADP 156.08 70.808.965 x 7.480 x 23.154Two Strap Adapter J700 2.75 LIP
1330706 ADP 155.20 70.408.965 x 7.480 x 23.154Two Strap Adapter J700 2.75 LIP
1711704 ADP 178.57 81.009.059 x 7.406 x 27.203Two Strap Adapter J700 3.00 LIP
1711705 ADP 177.91 80.709.059 x 7.406 x 27.203Two Strap Adapter J700 3.00 LIP
1711706 ADP 176.81 80.209.059 x 7.406 x 27.203Two Strap Adapter J700 3.00 LIP
2227700 ADP 185.19 84.009.252 x 7.480 x 28.386Two Strap Adapter J700 3.50 LIP
2227700LH ADP 185.19 84.009.252 x 7.480 x 28.386Two Strap Adapter LH
2227700RH ADP 184.52 83.707.480 x 9.252 x 28.386Two Strap Adapter RH
4T4708 PIN 2.58 1.17Standard Groove Pin
4T4707 RET 0.36 0.16Standard Retainer
9U9616 PIN 2.58 1.17Radius Groove Pin
4T4707 RET 0.36 0.16Retainer with Plastic Holder
1134708 PIN 2.58 1.17Heavy Duty Pin
1134709 RET 0.11 0.05Heavy Duty Coiled Retainer
J800 TEETH Serial Number:J800VX TOOTH 124.91 56.669.631 x 9.292 x 21.000Penetration Tooth
1359800 TOOTH 202.40 91.819.329 x 9.438 x 19.375Hevy Duty Penetration Tooth
J800HDAL TOOTH 206.50 93.679.385 x 9.250 x 20.000Heavy Duty Abrasion Tooth
6I8804 ADP 218.03 98.9010.433 x 8.661 x 27.303Two Strap Adapter J800 4.00 LIP
1020101 PIN 3.90 1.77Standard Groove Pin
1012874 RET 0.45 0.20Standard Retainer
1341808 PIN 3.75 1.70Heavy Duty Pin
1341809 RET 0.13 0.06Heavy Duty Coiled Retainer
MISCELLANEOUS TEETH AND ADAPTERS Serial Number:1324720 UNITOO 2 2.38 4.00 1.812.000 x 2.313 x 9.188Bolt on Unitooth 0.625
1359390 UNITOO 2 1.94 1.94 3.60 1.630.688 x 1.688 x 9.250Bolt on Unitooth 0.625
1386410 UNITOO 2 1.16 1.75 2.50 1.130.438 x 1.688 x 7.313Bolt on Unitooth 0.500
1358203 UNITOO 2 2.21 2.95 6.31 2.862.755 x 2.375 x 11.000Bolt on Unitooth 0.625
4K6936 TOOTH 3.40 1.54Top Pin Cat Tooth
4K6936SXC TOOTH 3.48 1.58 x 2.247 x 7.516Top Pin Cat SXC Tooth
4K6936TIGER TOOTH 2.90 1.32 x 2.375 x 7.500Top Pin Cat Tiger Tooth
4K6984 ADP 5.50 2.49Top Pin Cat Adapter
4K0034SXC TOOTH 4.94 2.242.839 x 2.673 x 7.850Top Pin Cat SXC Tooth
4K0034TIGER TOOTH 5.20 2.362.717 x 2.625 x 7.850Top Pin Cat Tiger Tooth
4K0034RMC18 ADP 6.00 2.722.823 x 2.760 x 9.381Top Pin Cat Adapter
R300 RIPPER TEETH AND COMPONENTS D4, D5, 12, 120, 130, 14, 140, 16, 160Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 6©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Teeth
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6Y0309 TOOTH 12.30 5.58Penetration
1681309 TOOTH 13.30 6.03Penetration C/IMP
8E7300 NOSE 1 5.47 2.482.188 x 3.438 x 5.313Weld on Nose
9J6586 SHANK 2 55.80 25.312.250 x 7.956 x 21.349Ripper Shank
1368308 PIN 0.44 0.20Heavy Duty Pin
1140359 RET 0.06 0.03Heavy Duty Coiled Retainer
9W2668 PIN 0.43 0.20Standard Groove Pin
6Y9459 RET 0.10 0.05Standard Retainer
R350 RIPPER TEETH AND COMPONENTS D5, D6, D7, 24HSerial Number:
6Y0359 TOOTH 28.20 12.79Penetration
1590356 TOOTH 28.20 12.79Penetration C/IMP
6Y0352 TOOTH 26.00 11.795.817 x 4.732 x 14.000Centerline
1590355 TOOTH 29.40 13.34Centerline C/IMP
8E7350 NOSE 1 11.99 5.442.938 x 4.438 x 6.625Weld on Nose
1380797 SHANK 3 122.90 55.752.938 x 10.456 x 28.402Ripper Shank 16, 24, D5, D6 99.999
1380796 PROT 1 20.94 9.504.300 x 5.375 x 12.750Shank Protector 0.938
1140358 PIN 0.53 0.24Heavy Duty Pin
1140359 RET 0.06 0.03Heavy Duty Coiled Retainer
9W2678 PIN 1.00 0.45Standard Groove Pin
6Y9459 RET 0.10 0.05Standard Retainer
R450 RIPPER TEETH AND COMPONENTS D8, D9Serial Number:
4T5451 TOOTH 37.04 16.806.833 x 5.577 x 12.875Short Penetration
9W2451 TOOTH 40.34 18.306.765 x 5.633 x 12.875Short Centerline
4T5452 TOOTH 41.20 18.69Intermediate Penetration
8E5771 TOOTH 45.00 20.41Intermediate Penetration C/IMP
9W2452 TOOTH 49.30 22.36Intermediate Centerline
8E5770 TOOTH 50.00 22.68Intermediate Centerline C/IMP
1140453 TOOTH 52.25 23.70Long Centerline
9U9694 NOSE 2 42.59 19.322.875 x 8.000 x 12.250Weld on Nose 1.063
8E8418 NOSE 3 5.30 3.06 12.34 156.30 70.903.241 x 12.754 x 17.418Weld on Nose 1.063
6J8814 PROT 2 12.25 27.00 12.253.000 x 4.250 x 17.000Standard 2 Pin Protector 1.375
6J8814EXT PROT 2 12.25 51.20 23.223.000 x 4.750 x 23.000Standard 2 Pin Protector Extended 1.375
1324716 PROT 2 12.31 51.90 23.543.188 x 12.199 x 27.108Standard 2 Pin Protector Extended 1.313
8E1848 PROT 2 12.25 56.10 25.453.000 x 5.000 x 19.125Sharp 2 Pin Protector 1.375
1386450 PINHeavy Duty Pin
1078559 RET 0.09 0.04Heavy Duty Coiled Retainer
6Y3394 PIN 1.07 0.49Standard Groove Pin
8E4743 RET 0.15 0.07Standard Retainer
R500 RIPPER TEETH AND COMPONENTS D9, D10, D11Serial Number:
4T5501 TOOTH 1 54.85 24.888.604 x 6.156 x 15.000Short Penetration 0.750
4T5502 TOOTH 68.40 31.039.250 x 6.500 x 16.750Intermediate Penetration
8E5772 TOOTH 72.00 32.66Intermediate Penetration C/IMP
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 7©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Teeth
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T5503 TOOTH 67.00 30.399.250 x 6.438 x 18.500Long Penetration
4T4501 TOOTH 55.11 25.008.624 x 6.169 x 14.760Short Centerline
4T4502 TOOTH 1 59.44 26.968.657 x 6.153 x 16.500Intermediate Centerline 0.750
8E8503 TOOTH 75.00 34.029.239 x 6.488 x 19.000Long Centerline
1038114 NOSE 2 96.90 43.953.938 x 10.563 x 17.438Weld on Nose
1038115 NOSE 2 4.38 166.70 75.613.938 x 12.625 x 20.500Weld on Nose
1073361 NOSE 2 95.80 43.453.938 x 11.063 x 15.125Weld on Nose 1.375
6Y8960 PROT 2 16.00 87.60 39.734.000 x 12.188 x 22.062 1.500
1321015 PROT 2 16.00 173.70 78.794.000 x 19.000 x 34.250Sharp 2 Pin Protector Extended 1.500
9W8365EXT PROT 2 16.00 97.10 44.043.500 x 5.750 x 34.375Sharp 2 Pin Protector Extended 1.625
1U3644 PROT 1 5.90 90.10 40.874.125 x 9.000 x 29.000Old Style Shank Protector 99.999
1386508 PINHeavy Duty Pin
1134709 RET 0.11 0.05Heavy Duty Coiled Retainer
6Y1204 PIN 1.90 0.86Imapct Style Pin
6Y1202 RET 0.40 0.18Impact Syle Retainer
6Y3909 PIN 1.90 0.86Standard Groove Pin
4T4707 RET 0.36 0.16Standard Retainer
R550 RIPPER TEETH AND COMPONENTS D11Serial Number:
6Y3552 TOOTH 1 109.08 49.4810.931 x 6.844 x 21.250Intermediate Penetration
9W4551 TOOTH 97.20 44.0911.153 x 7.358 x 17.625Short Centerline
9W4552 TOOTH 114.70 52.0311.153 x 7.358 x 21.250Intermediate Centerline
1359552 TOOTH 111.70 50.6710.931 x 6.844 x 21.250Intermediate Penetration C/IMP
1222552 TOOTH 116.70 52.9311.153 x 7.358 x 21.250Intermediate Centerline C/IMP
1049279 NOSE 2 275.60 125.014.375 x 16.262 x 24.030Weld on Nose
9N4621 PROT 2 23.25 166.89 75.704.500 x 12.688 x 28.768Sharp 2 Pin Protector 1.750
1321016 PROT 2 23.25 233.69 106.004.500 x 16.506 x 36.597Sharp 2 Pin Protector Extended 1.750
1590558 PINHeavy Duty Pin
1341809 RET 0.13 0.06Heavy Duty Coiled Retainer
9N4245 PIN 2.65 1.20Imapct Style Pin
6Y1205 RET 0.50 0.23Impact Syle Retainer
8E2229 PIN 2.65 1.20Standard Groove Pin
8E2230 RET 0.50 0.23Standard Retainer
GRADER SCARIFIER TEETH Serial Number:6Y5230 TOOTH 3.40 1.541.438 x 1.906 x 7.125Grader Scarifier Tooth
6Y5230LP TOOTH 3.53 1.601.900 x 1.871 x 8.491Grader Scarifier Tooth HD
1433074 TOOTHGrader Scarifier Tooth C/IMP
5B6251 SHANK 9.50 4.311.000 x 2.500 x 15.130Grader Scarifier Shank CAT Style 15"
9F5124 SHANK 12.39 5.621.000 x 3.000 x 17.250Grader Scarifier Shank CAT Style 17"
101 SHANK 12.60 5.721.000 x 3.000 x 17.250Grader Scarifier Shank Universal 17"
104 SHANK 14.50 6.581.000 x 3.000 x 20.000Grader Scarifier Shank Universal 20"
9F5124BS SHANK 12.60 5.721.000 x 3.000 x 17.246Grader Scarifier Shank Back Slots
5K1459 1 1.39 0.60 0.270.688 x 4.500 x 2.000Wedge 0.438
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 8©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
D3 D3B D3C Straight6EH 15W 86USerial Number:
4T6230 2 DB|| 6 2.13 6.00 6.00 34.20 15.5160.625 x 6.500 x 34.250Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D25096 SE|| 18 4.00 2.50 2.50 90.00 40.820.625 x 5.500 x 95.000Dozer Blade/End Bit Support 0.688
D3 D3B D3C Straight31M 40VSerial Number:
4T6231 2 DB|| 7 2.94 6.00 6.00 44.00 19.9670.625 x 6.500 x 41.875End 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 D3B D3C Power Angle Tilt9RH 1GP 8SU 2JPSerial Number:
4T6230 2 DB|| 6 2.13 6.00 6.00 34.20 15.5160.625 x 6.500 x 34.250Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D25096 SE|| 18 4.00 2.50 2.50 90.00 40.820.625 x 5.500 x 95.000Dozer Blade/End Bit Support 0.688
D3 D3B D3C Power Angle Tilt5WH 96X 8JPSerial Number:
4T6232 2 DB|| 8 2.88 6.00 6.00 48.00 21.7780.625 x 6.500 x 47.750Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 C Power Angle Tilt8HP 8KPSerial Number:
6Y5841 2 DB|| 6 2.94 6.00 6.00 36.00 16.3360.625 x 6.500 x 35.875Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 C Power Angle Tilt8XPSerial Number:
1410413 2 DB|| 8 3.30 6.00 6.00 54.00 24.4980.625 x 6.500 x 48.600Center 0.625 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 C Super Straight LGP5LHSerial Number:
4T6231 1 DB|| 7 2.94 6.00 6.00 44.00 19.9670.625 x 6.500 x 41.875Center 0.625 x 2.25
4T6230 2 DB|| 6 2.13 6.00 6.00 34.20 15.5160.625 x 6.500 x 34.250End 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 C Narrow Power Angle Tilt LGPNASerial Number:
1577338 2 DB|| 7 3.63 6.00 6.00 45.00 20.4170.625 x 6.500 x 43.250Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 K K2 Power Angle Tilt XL & LGP2775647 2862936Serial Number:
4T6232 2 DB|| 8 2.88 6.00 6.00 48.00 21.7780.625 x 6.500 x 47.750Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 K K2 Power Angle Tilt XL & LGP2551503 2552391 2552394Serial Number:
2551505 2 DB|| 6 4.50 6.00 6.00 59.70 27.080.750 x 8.000 x 38.500Center 0.750 x 2.75
8E7078REV 2 DB|| 4 4.50 3.00 3.00 27.50 12.4740.750 x 8.000 x 17.875Level Cut End Bit LH/RH 0.750 x 2.75
8E7078 1 DB/| 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit RH 0.750 x 2.75
8E7079 1 DB|\ 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit LH 0.750 x 2.75
8E7078LHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit RH 0.750 x 2.75
8E7079RHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit LH 0.750 x 2.75
D3 K K2 Power Angle Tilt XL & LGP2551487 2552386 3128351 3128361Serial Number:
1577338 2 DB|| 7 3.63 6.00 6.00 45.00 20.4170.625 x 6.500 x 43.250Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 K K2 Power Angle Tilt XL & LGP2551395 2552373Serial Number:
1406836 2 DB|| 6 3.50 6.00 6.000.625 x 6.500 x 37.000Center 0.625
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 K K2 Power Angle Tilt XL & LGP2551427 2552379Serial Number:
2551429 2 DB|| 6 5.25 6.00 6.00 40.50 18.370.625 x 6.500 x 40.500Center 0.625
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D3 K K2 Power Angle Tilt XL & LGP2551471 2552383Serial Number:
2551474 2 DB|| 8 3.60 6.00 6.00 49.10 22.270.625 x 6.500 x 49.193Center 0.625
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 Angle12D 78D 05F1-2850Serial Number:
4T2977 1 DB|| 18 1.94 4.00 4.00 91.40 41.46180.625 x 8.000 x 71.875Center 0.625 x 2
4T3021 1 DB|| 18 1.94 4.00 4.00 111.10 50.39180.750 x 8.000 x 71.875Heavy Duty Center 0.625 x 2
4T3043 1 DB/| 3 1.95 2.50 2.50 16.50 7.4830.750 x 8.000 x 11.398Level Cut End Bit RH 0.625 x 2.25
4T3044 1 DB|\ 3 1.95 2.50 2.50 16.50 7.4830.750 x 8.000 x 11.398Level Cut End Bit LH 0.625 x 2.25
5A4565 1 EBHC 3 2.00 2.50 2.50 26.50 12.0230.875 x 10.000 x 13.250Hot Cup End Bit RH 0.625 x 2.25
5A4566 1 EBHC 3 2.00 2.50 2.50 26.50 12.0230.875 x 10.000 x 13.250Hot Cup End Bit LH 0.625 x 2.25
D4 Angle05F 97E 24F 65FSerial Number:
4T2979 1 DB|| 13 3.94 6.00 6.00 102.40 46.45130.625 x 8.000 x 79.875Center 0.625 x 2
4T3043 1 DB/| 3 1.95 2.50 2.50 16.50 7.4830.750 x 8.000 x 11.398Level Cut End Bit RH 0.625 x 2.25
4T3044 1 DB|\ 3 1.95 2.50 2.50 16.50 7.4830.750 x 8.000 x 11.398Level Cut End Bit LH 0.625 x 2.25
5A4565 1 EBHC 3 2.00 2.50 2.50 26.50 12.0230.875 x 10.000 x 13.250Hot Cup End Bit RH 0.625 x 2.25
5A4566 1 EBHC 3 2.00 2.50 2.50 26.50 12.0230.875 x 10.000 x 13.250Hot Cup End Bit LH 0.625 x 2.25
D4 Angle10D 79D 06F1-11299Serial Number:
4T2981 1 DB|| 23 1.94 4.00 4.00 116.80 52.98230.625 x 8.000 x 91.875Center 0.625 x 2
4T3043 1 DB/| 3 1.95 2.50 2.50 16.50 7.4830.750 x 8.000 x 11.398Level Cut End Bit RH 0.625 x 2.25
4T3044 1 DB|\ 3 1.95 2.50 2.50 16.50 7.4830.750 x 8.000 x 11.398Level Cut End Bit LH 0.625 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 3©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
5A4565 1 EBHC 3 2.00 2.50 2.50 26.50 12.0230.875 x 10.000 x 13.250Hot Cup End Bit RH 0.625 x 2.25
5A4566 1 EBHC 3 2.00 2.50 2.50 26.50 12.0230.875 x 10.000 x 13.250Hot Cup End Bit LH 0.625 x 2.25
D4 D E Angle52E 96E 26F 06F11300-UP 95G 33RSerial Number:
4T2974 1 DB|| 5 3.94 6.00 6.00 40.90 18.5550.625 x 8.000 x 31.875Center 0.625 x 2
4T2973 2 DB|| 6 1.88 6.00 6.00 43.20 19.6060.625 x 8.000 x 33.750End 0.625 x 2
4T3043 1 DB/| 3 1.95 2.50 2.50 16.50 7.4830.750 x 8.000 x 11.398Level Cut End Bit RH 0.625 x 2.25
4T3044 1 DB|\ 3 1.95 2.50 2.50 16.50 7.4830.750 x 8.000 x 11.398Level Cut End Bit LH 0.625 x 2.25
5A4565 1 EBHC 3 2.00 2.50 2.50 26.50 12.0230.875 x 10.000 x 13.250Hot Cup End Bit RH 0.625 x 2.25
5A4566 1 EBHC 3 2.00 2.50 2.50 26.50 12.0230.875 x 10.000 x 13.250Hot Cup End Bit LH 0.625 x 2.25
D4 H Angle6AC 2GCSerial Number:
4T8940 2 DB|| 8 2.50 6.00 6.00 59.90 27.1780.625 x 8.000 x 47.000Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D4 Straight04A 40DSerial Number:
4T2977 1 DB|| 18 1.94 4.00 4.00 91.40 41.46180.625 x 8.000 x 71.875Center 0.625 x 2
4T3021 1 DB|| 18 1.94 4.00 4.00 111.10 50.39180.750 x 8.000 x 71.875Heavy Duty Center 0.625 x 2
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D4 Straight02A 25F 67FSerial Number:
4T2980 1 DB|| 15 1.94 4.00 4.00 76.10 34.52150.625 x 8.000 x 59.875Center 0.625 x 2
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D4 Straight93CSerial Number:
8A8580 1 DB|| 4 3.31 6.00 6.00 31.60 14.3340.625 x 8.000 x 24.625Center 0.625 x 2
8A8581 2 DB|| 4 2.50 6.00 6.00 29.40 13.3440.625 x 8.000 x 23.000End 0.625 x 2
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 4©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D4 E Straight67E 27F 94GSerial Number:
4T2983 1 DB|| 3 1.50 6.00 6.00 19.20 8.7130.625 x 8.000 x 15.000Center 0.625 x 2
4T2972 2 DB|| 4 4.25 6.00 6.00 34.00 15.4240.625 x 8.000 x 26.500End 0.625 x 2
4T3027 1 DB|| 3 1.50 6.00 6.00 23.30 10.5730.750 x 8.000 x 15.000Heavy Duty Center 0.625 x 2
4T3028 2 DB|| 4 4.25 6.00 6.00 41.40 18.7840.750 x 8.000 x 26.500Heavy Duty End 0.625 x 2
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D4 H Straight2TC 3CH 3DCSerial Number:
4T3720 2 DB|| 6 1.94 6.00 6.00 43.20 19.6060.625 x 8.000 x 33.875Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D4 E Straight LGP84E 19J 45JSerial Number:
4T2982 1 DB|| 7 1.50 6.00 6.00 49.90 22.6370.625 x 8.000 x 39.000Center 0.625 x 2
4T2972 2 DB|| 4 4.25 6.00 6.00 34.00 15.4240.625 x 8.000 x 26.500End 0.625 x 2
4T3029 1 DB|| 7 1.50 6.00 6.00 60.60 27.4970.750 x 8.000 x 39.000Heavy Duty Center 0.625 x 2
4T3028 2 DB|| 4 4.25 6.00 6.00 41.40 18.7840.750 x 8.000 x 26.500Heavy Duty End 0.625 x 2
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D4 H Straight LGP4HCSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 5©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T8940 2 DB|| 8 2.50 6.00 6.00 59.90 27.1780.625 x 8.000 x 47.000Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D4 B C Power Angle Tilt2YHSerial Number:
4T6230 2 DB|| 6 2.13 6.00 6.00 34.20 15.5160.625 x 6.500 x 34.250Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D25096 SE|| 18 4.00 2.50 2.50 90.00 40.820.625 x 5.500 x 95.000Dozer Blade/End Bit Support 0.688
D4 C Power Angle Tilt6CHSerial Number:
6Y5841 2 DB|| 6 2.94 6.00 6.00 36.00 16.3360.625 x 6.500 x 35.875Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 C Power Angle Tilt9SHSerial Number:
1049634 2 DB|| 6 4.19 6.00 6.00 38.40 17.4260.625 x 6.500 x 38.375Center 0.625 x 2.25
2085277 2 DB|| 6 4.18 6.00 6.00 52.10 23.6360.875 x 6.500 x 38.375Heavy Duty Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 C Power Angle Tilt8LPSerial Number:
1402187 2 DB|| 6 4.90 6.00 6.00 41.00 18.6060.625 x 6.500 x 39.800Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 H Power Angle Tilt9ZB 4AC 5NH 7EHSerial Number:
3G9306 2 DB|| 6 2.40 6.00 6.00 44.30 20.0960.625 x 8.000 x 34.800Center 0.750 x 2.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 6©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D4 B C Power Angle Tilt LGP4GH 9YH 8ZHSerial Number:
4T6232 2 DB|| 8 2.88 6.00 6.00 48.00 21.7780.625 x 6.500 x 47.750Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 C Power Angle Tilt LGP6DH 9TH 8MPSerial Number:
6Y5842 2 DB|| 8 3.94 6.00 6.00 49.80 22.5980.625 x 6.500 x 49.875Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 C Power Angle Tilt LGP8YPSerial Number:
1412238 2 DB|| 8 4.75 6.00 6.00 53.00 24.0480.625 x 6.500 x 51.500Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 H Power Angle Tilt LGP5EC 5RH 7CHSerial Number:
4T8940 2 DB|| 8 2.50 6.00 6.00 59.90 27.1780.625 x 8.000 x 47.000Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D4 H Power Angle Tilt XL6XHSerial Number:
8E9377 2 DB|| 7 2.75 6.00 6.00 52.90 24.0070.625 x 8.000 x 41.500Center 0.750 x 2.5
4T6659 2 DB|| 7 2.75 6.00 6.00 64.40 29.2170.750 x 8.000 x 41.500Heavy Duty Center 0.750 x 2.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 7©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D4 K K2 Power Angle Tilt XL & LGP2551362 2551414 2552370 2552376Serial Number:
4T6232 2 DB|| 8 2.88 6.00 6.00 48.00 21.7780.625 x 6.500 x 47.750Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 K K2 Power Angle Tilt XL & LGP2551487 2552386 3128351 3128361Serial Number:
1577338 2 DB|| 7 3.63 6.00 6.00 45.00 20.4170.625 x 6.500 x 43.250Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 K K2 Power Angle Tilt XL & LGP2551395 2552373Serial Number:
1406836 2 DB|| 6 3.50 6.00 6.000.625 x 6.500 x 37.000Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 K K2 Power Angle Tilt XL & LGP2551427 2552379Serial Number:
2551429 2 DB|| 6 5.25 6.00 6.00 40.50 18.370.625 x 6.500 x 40.500Center 0.625
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 K K2 Power Angle Tilt XL & LGP2551471 2552383Serial Number:
2551474 2 DB|| 8 3.60 6.00 6.00 49.10 22.270.625 x 6.500 x 49.193Center 0.625
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 8©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D4 K K2 Power Angle Tilt XL & LGP2551503 2552391 2552394Serial Number:
2551505 2 DB|| 6 4.50 6.00 6.00 59.70 27.080.750 x 8.000 x 38.500Center 0.750 x 2.75
8E7078REV 2 DB|| 4 4.50 3.00 3.00 27.50 12.4740.750 x 8.000 x 17.875Level Cut End Bit LH/RH 0.750 x 2.75
8E7078 1 DB/| 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit RH 0.750 x 2.75
8E7079 1 DB|\ 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit LH 0.750 x 2.75
8E7078LHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit RH 0.750 x 2.75
8E7079RHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit LH 0.750 x 2.75
D4 K K2 Power Angle Tilt XL & LGP2551503 2552391 2552394Serial Number:
3310162 2 DB|| 6Center 0.750
8E7078REV 2 DB|| 4 4.50 3.00 3.00 27.50 12.4740.750 x 8.000 x 17.875Level Cut End Bit LH/RH 0.750 x 2.75
8E7078 1 DB/| 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit RH 0.750 x 2.75
8E7079 1 DB|\ 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit LH 0.750 x 2.75
8E7078LHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit RH 0.750 x 2.75
8E7079RHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit LH 0.750 x 2.75
D5 Angle91H 96H 42KSerial Number:
4T3030 2 DB|| 12 1.94 4.00 4.00 73.90 33.52120.750 x 8.000 x 47.875Center 0.625 x 2.25
4T2978 1 DB|| 24 1.94 4.00 4.00 121.90 55.29240.625 x 8.000 x 95.875Optional One Piece Edge 0.625 x 2.25
4T3049 1 DB/| 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
4T3050 1 DB|\ 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
3G8295 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
3G8296 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
D5 D5B Angle93H1-3846 98H 11J 13JSerial Number:
4T3008 1 DB|| 11 2.94 4.00 4.00 71.00 32.21110.750 x 8.000 x 45.875Center 0.625 x 2.25
4T3020 2 DB|| 9 0.91 4.00 4.00 52.20 23.6890.750 x 8.000 x 33.813End 0.625 x 2.25
4T3049 1 DB/| 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
4T3050 1 DB|\ 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
3G8295 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
3G8296 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
D5 B Angle93H3847-UPSerial Number:
4T3004 2 DB|| 9 4.38 6.00 6.00 88.10 39.9690.750 x 8.000 x 56.750Center 0.750 x 2.25
4T3041 1 DB/| 6 1.93 3.50 3.50 20.80 9.4330.750 x 8.000 x 14.890Level Cut End Bit RH 0.750 x 2.253 1.93 4.00 4.00 ...2nd Row0.750 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 9©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T3042 1 DB|\ 6 1.93 3.50 3.50 20.80 9.4330.750 x 8.000 x 14.890Level Cut End Bit LH 0.750 x 2.253 1.93 4.00 4.00 ...2nd Row0.750 x 2.25
4J8261 1 EBC 6 2.00 3.50 3.50 24.80 11.2530.750 x 8.999 x 14.996Cast End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
4J8262 1 EBC 6 2.00 3.50 3.50 24.80 11.2530.750 x 8.999 x 14.996Cast End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
3G8297 1 EBHC 6 2.00 3.50 3.50 35.90 16.2831.000 x 10.300 x 15.440Hot Cup End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
3G8298 1 EBHC 6 2.00 3.50 3.50 35.90 16.2831.000 x 10.300 x 15.440Hot Cup End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
9W9010HC 1 EBHC 6 2.00 3.50 3.50 47.50 21.5531.125 x 11.000 x 17.750Hot Cup End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
9W9011HC 1 EBHC 6 2.00 3.50 3.50 47.50 21.5531.125 x 11.000 x 17.750Hot Cup End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
D5 E Angle6RHSerial Number:
1024580 2 DB|| 8 5.00 6.00 6.00 80.00 36.2980.750 x 8.000 x 52.000Center 0.750 x 2.25
4T3041 1 DB/| 6 1.93 3.50 3.50 20.80 9.4330.750 x 8.000 x 14.890Level Cut End Bit RH 0.750 x 2.253 1.93 4.00 4.00 ...2nd Row0.750 x 2.25
4T3042 1 DB|\ 6 1.93 3.50 3.50 20.80 9.4330.750 x 8.000 x 14.890Level Cut End Bit LH 0.750 x 2.253 1.93 4.00 4.00 ...2nd Row0.750 x 2.25
4J8261 1 EBC 6 2.00 3.50 3.50 24.80 11.2530.750 x 8.999 x 14.996Cast End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
4J8262 1 EBC 6 2.00 3.50 3.50 24.80 11.2530.750 x 8.999 x 14.996Cast End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
3G8297 1 EBHC 6 2.00 3.50 3.50 35.90 16.2831.000 x 10.300 x 15.440Hot Cup End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
3G8298 1 EBHC 6 2.00 3.50 3.50 35.90 16.2831.000 x 10.300 x 15.440Hot Cup End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
9W9010HC 1 EBHC 6 2.00 3.50 3.50 47.50 21.5531.125 x 11.000 x 17.750Hot Cup End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
9W9011HC 1 EBHC 6 2.00 3.50 3.50 47.50 21.5531.125 x 11.000 x 17.750Hot Cup End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
D5 H Angle3AH 2FH 2THSerial Number:
4T3013 1 DB|| 7 1.94 6.00 6.00 61.80 28.0370.750 x 8.000 x 39.875Center 0.750 x 2.5
1U2207 2 DB|| 6 3.94 6.00 6.00 58.80 26.6760.750 x 8.000 x 37.875End 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D5 D5B Straight90HSerial Number:
4T2983 1 DB|| 3 1.50 6.00 6.00 19.20 8.7130.625 x 8.000 x 15.000Center 0.625 x 2.25
4T2972 2 DB|| 4 4.25 6.00 6.00 34.00 15.4240.625 x 8.000 x 26.500End 0.625 x 2.25
4T3027 1 DB|| 3 1.50 6.00 6.00 23.30 10.5730.750 x 8.000 x 15.000Heavy Duty Center 0.625 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 10©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T3028 2 DB|| 4 4.25 6.00 6.00 41.40 18.7840.750 x 8.000 x 26.500Heavy Duty End 0.625 x 2.25
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D5 D5B Straight92H 97H 10J 12JSerial Number:
4T3025 1 DB|| 7 3.94 6.00 6.00 68.40 31.0370.750 x 8.000 x 43.875Center 0.625 x 2.25
4T3026 2 DB|| 4 1.94 6.00 6.00 34.00 15.4240.750 x 8.000 x 21.875End 0.625 x 2.25
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D5 D5B Straight16K 19RSerial Number:
4T3024 1 DB|| 28 1.44 4.00 4.00 171.20 77.66280.750 x 8.000 x 110.875Center 0.625 x 2.25
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D5 H Straight2BH 4FHSerial Number:
3G6062 2 DB|| 7 2.56 6.00 6.00 63.70 28.8970.750 x 8.000 x 41.125Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D5 H Straight LGP1ZH 3KHSerial Number:
1U2211 2 DB|| 9 3.44 6.00 6.00 85.10 38.6090.750 x 8.000 x 54.875Center 0.750 x 2.25
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 11©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D5 H Petroleum Field Blade4AHSerial Number:
4T0731 2 DB|| 5 4.06 6.00 6.00 51.00 23.1350.750 x 8.000 x 32.125Center 0.750 x 2.25
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D5 C Power Angle Tilt9WH 6MHSerial Number:
3G9306 2 DB|| 6 2.40 6.00 6.00 44.30 20.0960.625 x 8.000 x 34.800Center 0.750 x 2.75
8E7078REV 2 DB|| 4 4.50 3.00 3.00 27.50 12.4740.750 x 8.000 x 17.875Level Cut End Bit LH/RH 0.750 x 2.75
8E7078 1 DB/| 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit RH 0.750 x 2.75
8E7079 1 DB|\ 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit LH 0.750 x 2.75
8E7078LHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit RH 0.750 x 2.75
8E7079RHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit LH 0.750 x 2.75
D27919BS 1 SE\_/ 14 2.75 3.00 3.00 127.00 57.610.750 x 6.000 x 102.500Dozer Blade Support 0.813
D5 C Power Angle Tilt8GPSerial Number:
1400983 2 DB|| 6 2.94 6.00 6.00 45.70 20.7360.625 x 8.000 x 35.875Center 0.750 x 2.75
8E7078REV 2 DB|| 4 4.50 3.00 3.00 27.50 12.4740.750 x 8.000 x 17.875Level Cut End Bit LH/RH 0.750 x 2.75
8E7078 1 DB/| 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit RH 0.750 x 2.75
8E7079 1 DB|\ 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit LH 0.750 x 2.75
8E7078LHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit RH 0.750 x 2.75
8E7079RHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit LH 0.750 x 2.75
D5 H Power Angle Tilt2AH 2MH 7AHSerial Number:
3G4282 2 DB|| 7 4.69 6.00 6.00 70.00 31.7570.750 x 8.000 x 45.375Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
8E9502 SE|| 22 3.00 3.00 172.80 78.380.750 x 6.693 x 124.354Dozer Blade/End Bit Support 0.813
D5 M N Power Angle Tilt4GP 6JPSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 12©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E9377 2 DB|| 7 2.75 6.00 6.00 52.90 24.0070.625 x 8.000 x 41.500Center 0.750 x 2.5
4T6659 2 DB|| 7 2.75 6.00 6.00 64.40 29.2170.750 x 8.000 x 41.500Heavy Duty Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D5 M N Power Angle Tilt XLHGPSerial Number:
8E9377 2 DB|| 7 2.75 6.00 6.00 52.90 24.0070.625 x 8.000 x 41.500Center 0.750 x 2.5
4T6659 2 DB|| 7 2.75 6.00 6.00 64.40 29.2170.750 x 8.000 x 41.500Heavy Duty Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D5 M N Power Angle Tilt XLW5CSerial Number:
5Q8193 2 DB|| 6Center 0.750
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D5 M N Power Angle Tilt XWNASerial Number:
1577338 2 DB|| 7 3.63 6.00 6.00 45.00 20.4170.625 x 6.500 x 43.250Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D5 C Power Angle Tilt LGP6PH 9XH 8NPSerial Number:
6Y5842 2 DB|| 8 3.94 6.00 6.00 49.80 22.5980.625 x 6.500 x 49.875Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 13©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D5 C Power Angle Tilt LGP8ZPSerial Number:
1424914 2 DB|| 8 4.31 6.00 6.00 52.00 23.5980.625 x 6.500 x 50.625Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D40382 SE|| 22 3.00 2.50 2.50 158.30 71.800.750 x 6.000 x 125.625Dozer Blade/End Bit Support 0.688
D5 H Power Angle Tilt LGP2SH 1YHSerial Number:
4T2315 2 DB|| 10 3.63 6.00 6.00 95.00 43.09100.750 x 8.000 x 61.250Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
1127615 1 28 3.00 3.000.750 x 6.693 x 156.244Dozer Blade/End Bit Support 0.813
D5 M N Power Angle Tilt LGP4FP BHYSerial Number:
4T8940 2 DB|| 8 2.50 6.00 6.00 59.90 27.1780.625 x 8.000 x 47.000Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D5 H Semi-U7BHSerial Number:
4T6659 1 DB|| 7 2.75 6.00 6.00 64.40 29.2170.750 x 8.000 x 41.500Center 0.750 x 2.5
9U8057 2 DB|> 4 3.34 6.00 6.00 37.40 16.9640.750 x 8.000 x 24.688End 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D5 K K2 Power Angle Tilt XL & LGP2551395 2552373Serial Number:
1406836 2 DB|| 6 3.50 6.00 6.000.625 x 6.500 x 37.000Center 0.625 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 14©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D5 K K2 Power Angle Tilt XL & LGP2551427 2552379Serial Number:
2551429 2 DB|| 6 5.25 6.00 6.00 40.50 18.370.625 x 6.500 x 40.500Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D5 K K2 Power Angle Tilt XL & LGP2551487 2552386 3128351 3128361Serial Number:
1577338 2 DB|| 7 3.63 6.00 6.00 45.00 20.4170.625 x 6.500 x 43.250Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D5 K K2 Power Angle Tilt XL & LGP2551362 2552370 2552376Serial Number:
4T6232 2 DB|| 8 2.88 6.00 6.00 48.00 21.7780.625 x 6.500 x 47.750Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D5 K K2 Power Angle Tilt XL & LGP2551471 2552383Serial Number:
2551474 2 DB|| 8 3.60 6.00 6.00 49.10 22.270.625 x 6.500 x 49.193Center 0.625 x 2.25
4T6229 2 DB|| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.000Level Cut End Bit LH/RH 0.625 x 2.25
6Y5839 1 DB/| 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit RH 0.625 x 2.25
6Y5840 1 DB|\ 3 4.00 2.50 2.50 13.00 5.9030.625 x 6.500 x 13.875Level Cut End Bit LH 0.625 x 2.25
4T6229RHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit RH 0.625 x 2.25
4T6229LHHC 1 EBHC 3 4.00 2.50 2.50 22.60 10.2530.750 x 8.500 x 15.468Hot Cup End Bit LH 0.625 x 2.25
D5 K K2 Power Angle Tilt XL & LGP2551503 2552391 2552394Serial Number:
2551505 2 DB|| 6 4.50 6.00 6.00 59.70 27.080.750 x 8.000 x 38.500Center 0.750 x 2.75
8E7078REV 2 DB|| 4 4.50 3.00 3.00 27.50 12.4740.750 x 8.000 x 17.875Level Cut End Bit LH/RH 0.750 x 2.75
8E7078 1 DB/| 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit RH 0.750 x 2.75
8E7079 1 DB|\ 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit LH 0.750 x 2.75
8E7078LHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit RH 0.750 x 2.75
8E7079RHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit LH 0.750 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 15©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E7078 DB/| 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit RH 0.750 x 2.75
D5 K K2 Power Angle Tilt XL & LGP2551503 2552391 2552394Serial Number:
3310162 2 DB|| 6Center 0.750 x 2.75
8E7078REV 2 DB|| 4 4.50 3.00 3.00 27.50 12.4740.750 x 8.000 x 17.875Level Cut End Bit LH/RH 0.750 x 2.75
8E7078 1 DB/| 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit RH 0.750 x 2.75
8E7079 1 DB|\ 4 4.38 3.00 3.00 25.90 11.7540.750 x 8.000 x 17.875Level Cut End Bit LH 0.750 x 2.75
8E7078LHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit RH 0.750 x 2.75
8E7079RHHC 1 EBHC 4 4.38 3.00 3.00 35.30 16.0140.750 x 10.000 x 21.000Hot Cup End Bit LH 0.750 x 2.75
D6 Angle16C5001-UP 37D 81D 16E 03F 04F 40HSerial Number:
4T3008 1 DB|| 11 2.94 4.00 4.00 71.00 32.21110.750 x 8.000 x 45.875Center 0.625 x 2.25
4T3020 2 DB|| 9 0.91 4.00 4.00 52.20 23.6890.750 x 8.000 x 33.813End 0.625 x 2.25
3G8295 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
3G8296 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
4T3049 1 DB/| 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
4T3050 1 DB|\ 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
D6 Angle15C5001-UP 39D 82D 08E 09ESerial Number:
4T3030 2 DB|| 12 1.94 4.00 4.00 73.90 33.52120.750 x 8.000 x 47.875Center 0.625 x 2.25
4T2978 1 DB|| 24 1.94 4.00 4.00 121.90 55.29240.625 x 8.000 x 95.875Optional One Piece Edge 0.625 x 2.25
3G8295 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
3G8296 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
4T3049 1 DB/| 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
4T3050 1 DB|\ 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
D6 C D E G Angle54U 44E 47G 58G 18HSerial Number:
4T3009 2 DB|| 10 2.94 6.00 6.00 92.90 42.14100.750 x 8.000 x 59.875Center 0.750 x 2.25
4J8261 1 EBC 6 2.00 3.50 3.50 24.80 11.2530.750 x 8.999 x 14.996Cast End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
4J8262 1 EBC 6 2.00 3.50 3.50 24.80 11.2530.750 x 8.999 x 14.996Cast End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
3G8297 1 EBHC 6 2.00 3.50 3.50 35.90 16.2831.000 x 10.300 x 15.440Hot Cup End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
3G8298 1 EBHC 6 2.00 3.50 3.50 35.90 16.2831.000 x 10.300 x 15.440Hot Cup End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
9W9010HC 1 EBHC 6 2.00 3.50 3.50 47.50 21.5531.125 x 11.000 x 17.750Hot Cup End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
9W9011HC 1 EBHC 6 2.00 3.50 3.50 47.50 21.5531.125 x 11.000 x 17.750Hot Cup End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 16©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T3041 1 DB/| 6 1.93 3.50 3.50 20.80 9.4330.750 x 8.000 x 14.890Level Cut End Bit RH 0.750 x 2.253 1.93 4.00 4.00 ...2nd Row0.750 x 2.25
4T3042 1 DB|\ 6 1.93 3.50 3.50 20.80 9.4330.750 x 8.000 x 14.890Level Cut End Bit LH 0.750 x 2.253 1.93 4.00 4.00 ...2nd Row0.750 x 2.25
D6 H Angle1BH1-0659 4DH 4LH 3EHSerial Number:
4T6262 3 DB|| 7 2.06 6.00 6.00 62.20 28.2170.750 x 8.000 x 40.125Center 0.750 x 2.5
7T9977 3 DB|| 7 2.06 6.00 6.00 84.20 38.1971.000 x 8.000 x 40.125Heavy Duty Center 0.750 x 2.5
4T4455 1 EBHC 6 2.25 3.19 3.19 53.80 24.4031.250 x 10.750 x 17.500Hot Cup End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
4T4454 1 EBHC 6 2.25 3.19 3.19 53.80 24.4031.250 x 10.750 x 17.500Hot Cup End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
4T4435 1 DB/| 6 2.25 3.19 3.19 30.40 13.7931.000 x 8.000 x 16.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
4T4436 1 DB|\ 6 2.25 3.19 3.19 30.40 13.7931.000 x 8.000 x 16.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
D6 H Angle1BH0570-UPSerial Number:
4T2952 4 DB|| 5 3.75 6.00 6.00 61.10 27.7150.750 x 10.000 x 31.500Center 0.750 x 2.5
4T2985 4 DB|| 5 3.75 6.00 6.00 81.60 37.0151.000 x 10.000 x 31.500Heavy Duty Center 0.750 x 2.5
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
D6 R Angle1XP 3GP 1ZP 1YP 3PP 4BP 8TPSerial Number:
4T2952 4 DB|| 5 3.75 6.00 6.00 61.10 27.7150.750 x 10.000 x 31.500Center 0.750 x 2.5
4T2985 4 DB|| 5 3.75 6.00 6.00 81.60 37.0151.000 x 10.000 x 31.500Heavy Duty Center 0.750 x 2.5
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 17©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
6Y1812-8 1 SE|| 32 5.53 3.66 3.94 325.90 147.831.000 x 7.350 x 158.000Dozer Blade Support 0.813
D6 R AngleSERIES IIISerial Number:
2296958 2 DB|| 11 1.56 6.00 6.00 163.20 74.03111.000 x 10.000 x 63.125Center 0.750 x 2.5
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
D6 T AngleSerial Number:2194599 2 DB|| 11 1.56 6.00 6.00 112.00 50.800.750 x 10.000 x 57.720Center 0.750
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
D6 R Angle Custom Wide6HPSerial Number:
1099093 4 DB|| 6 2.50 6.00 6.00 67.00 30.3960.750 x 10.000 x 35.000Center 0.750 x 2.5
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 18©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
4Z9435-8 1 SE|| 36 5.53 3.66 3.94 355.00 161.031.000 x 7.500 x 172.000Dozer Blade Support 0.813
D6 T Angle Custom WideSerial Number:4T3011X10 2 DB|| 11 1.88 6.00 6.00 123.70 56.110.750 x 10.000 x 63.750Center 0.750
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
D6 M N Power Angle Tilt3WP 3XPSerial Number:
3G4282 2 DB|| 7 4.69 6.00 6.00 70.00 31.7570.750 x 8.000 x 45.375Center 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
8E9502 SE|| 22 3.00 3.00 172.80 78.380.750 x 6.693 x 124.354Dozer Blade/End Bit Support 0.813
D6 M N Power Angle Tilt XLB6X G6M G6NSerial Number:
3G4282 2 DB|| 7 4.69 6.00 6.00 70.00 31.7570.750 x 8.000 x 45.375Center 0.750 x 2.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 19©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
8E9502 SE|| 22 3.00 3.00 172.80 78.380.750 x 6.693 x 124.354Dozer Blade/End Bit Support 0.813
D6 M N Power Angle Tilt LGP4MP B6L G6GSerial Number:
4T2315 2 DB|| 10 3.63 6.00 6.00 95.00 43.09100.750 x 8.000 x 61.250Center 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1127615 1 28 3.00 3.000.750 x 6.693 x 156.244Dozer Blade/End Bit Support 0.813
D6 R Power Angle Tilt LGPG6MSerial Number:
3G4282 2 DB|| 7 4.69 6.00 6.00 70.00 31.7570.750 x 8.000 x 45.375Center 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
8E9502 SE|| 22 3.00 3.00 172.80 78.380.750 x 6.693 x 124.354Dozer Blade/End Bit Support 0.813
D6 R Power Angle Tilt LGP4TP 4WPSerial Number:
1273050 2 DB|| 10Center 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
D6 R FOLDABLE Power Angle LGPF6W F6YSerial Number:
1774550 2 9 3.23 6.56 6.56 91.50 41.500.750 x 8.000 x 58.898Center 0.750
1774551 1 DB/| 4 3.43 3.94 3.94 31.10 14.110.750 x 8.000 x 21.220Level Cut End Bit RH 0.750
1774552 1 DB|\ 4 3.43 3.94 3.94 31.10 14.110.750 x 8.000 x 21.220Level Cut End Bit LH 0.750
D6 Straight09A 01C 06CSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 20©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T2977 1 DB|| 18 1.94 4.00 4.00 91.40 41.46180.625 x 8.000 x 71.875Center 0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D6 Straight15C1-5000Serial Number:
4T3021 1 DB|| 18 1.94 4.00 4.00 111.10 50.39180.750 x 8.000 x 71.875Center 0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D6 Straight16C1-5000Serial Number:
4T2976 1 DB|| 22 1.94 4.00 4.00 111.80 50.71220.625 x 8.000 x 87.875Center 0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D6 Straight85C 36D 80D 38D 15E 02G 03G 39HSerial Number:
4T3023 1 DB|| 22 1.88 4.00 4.00 135.60 61.51220.750 x 8.000 x 87.750Center 0.625 x 2.25
3G8321 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
3G8322 1 EBHC 6 1.88 4.00 4.00 39.80 18.0531.000 x 10.000 x 17.500Hot Cup End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3051 1 DB/| 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit RH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
4T3052 1 DB|\ 6 1.88 4.00 4.00 19.70 8.9430.750 x 8.000 x 13.250Level Cut End Bit LH 0.625 x 2.253 1.88 4.00 4.00 ...2nd Row0.625 x 2.25
D6 D Straight21H 41HSerial Number:
4T3011 1 DB|| 11 1.88 6.00 6.00 98.80 44.81110.750 x 8.000 x 63.750Center 0.750 x 2.25
4T3010 2 DB|| 4 3.94 6.00 6.00 40.20 18.2340.750 x 8.000 x 25.875End 0.750 x 2.25
5J1419 1 EBC 6 2.25 4.00 4.00 31.70 14.3830.875 x 9.497 x 14.997Cast End Bit RH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 21©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
5J1420 1 EBC 6 2.25 4.00 4.00 31.70 14.3830.875 x 9.497 x 14.997Cast End Bit LH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
3G8319 1 EBHC 6 2.25 4.00 4.00 32.30 14.6530.875 x 9.610 x 16.940Hot Cup End Bit RH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
3G8320 1 EBHC 6 2.25 4.00 4.00 32.30 14.6530.875 x 9.610 x 16.970Hot Cup End Bit LH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
4T3045 1 DB/| 6 2.25 4.00 4.00 21.50 9.7530.750 x 8.000 x 14.850Level Cut End Bit RH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
4T3046 1 DB|\ 6 2.25 4.00 4.00 21.50 9.7530.750 x 8.000 x 14.750Level Cut End Bit LH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
D6 C D E G Straight95E 17H 46G 55G 63SSerial Number:
4T3013 1 DB|| 7 1.94 6.00 6.00 61.80 28.0370.750 x 8.000 x 39.875Center 0.750 x 2.25
4T3010 2 DB|| 4 3.94 6.00 6.00 40.20 18.2340.750 x 8.000 x 25.875End 0.750 x 2.25
4T3017 1 DB|| 15 3.88 6.00 6.00 142.40 64.59150.750 x 8.000 x 91.750Optional One Piece Edge 0.750 x 2.25
5J1419 1 EBC 6 2.25 4.00 4.00 31.70 14.3830.875 x 9.497 x 14.997Cast End Bit RH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
5J1420 1 EBC 6 2.25 4.00 4.00 31.70 14.3830.875 x 9.497 x 14.997Cast End Bit LH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
3G8319 1 EBHC 6 2.25 4.00 4.00 32.30 14.6530.875 x 9.610 x 16.940Hot Cup End Bit RH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
3G8320 1 EBHC 6 2.25 4.00 4.00 32.30 14.6530.875 x 9.610 x 16.970Hot Cup End Bit LH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
4T3045 1 DB/| 6 2.25 4.00 4.00 21.50 9.7530.750 x 8.000 x 14.850Level Cut End Bit RH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
4T3046 1 DB|\ 6 2.25 4.00 4.00 21.50 9.7530.750 x 8.000 x 14.750Level Cut End Bit LH 0.750 x 2.253 2.25 4.00 4.00 ...2nd Row0.750 x 2.25
D6 H Straight1DH1-0599 2HH 3JH 4BHSerial Number:
4T6659 1 DB|| 7 2.75 6.00 6.00 64.40 29.2170.750 x 8.000 x 41.500Center 0.750 x 2.5
4T3010 2 DB|| 4 3.94 6.00 6.00 40.20 18.2340.750 x 8.000 x 25.875End 0.750 x 2.5
7T9976 1 DB|| 7 2.75 6.00 6.00 87.10 39.5171.000 x 8.000 x 41.500Heavy Duty Center 0.750 x 2.5
7T9978 2 DB|| 4 3.94 6.00 6.00 54.50 24.7241.000 x 8.000 x 25.875Heavy Duty End 0.750 x 2.5
4T4455 1 EBHC 6 2.25 3.19 3.19 53.80 24.4031.250 x 10.750 x 17.500Hot Cup End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
4T4454 1 EBHC 6 2.25 3.19 3.19 53.80 24.4031.250 x 10.750 x 17.500Hot Cup End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
4T4435 1 DB/| 6 2.25 3.19 3.19 30.40 13.7931.000 x 8.000 x 16.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
4T4436 1 DB|\ 6 2.25 3.19 3.19 30.40 13.7931.000 x 8.000 x 16.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
D6 R Straight1DH600-UP 3EP CLH 1RP 3EP BHNSerial Number:
4T2952 3 DB|| 5 3.75 6.00 6.00 61.10 27.7150.750 x 10.000 x 31.500Center 0.750 x 2.5
4T2985 3 DB|| 5 3.75 6.00 6.00 81.60 37.0151.000 x 10.000 x 31.500Heavy Duty Center 0.750 x 2.5
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 22©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
8E5199-8 1 SE\_/ 27 5.90 3.66 3.94 256.00 116.121.000 x 7.500 x 127.000Dozer Blade Support 0.813
D6 M N R Straight LGP1AH 2LH 3FH 1SP 3HP BHGSerial Number:
4T6659 3 DB|| 7 2.75 6.00 6.00 64.40 29.2170.750 x 8.000 x 41.500Center 0.750 x 2.5
7T9976 3 DB|| 7 2.75 6.00 6.00 87.10 39.5171.000 x 8.000 x 41.500Center 0.750 x 2.5
4T4455 1 EBHC 6 2.25 3.19 3.19 53.80 24.4031.250 x 10.750 x 17.500Hot Cup End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
4T4454 1 EBHC 6 2.25 3.19 3.19 53.80 24.4031.250 x 10.750 x 17.500Hot Cup End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
4T4435 1 DB/| 6 2.25 3.19 3.19 30.40 13.7931.000 x 8.000 x 16.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
4T4436 1 DB|\ 6 2.25 3.19 3.19 30.40 13.7931.000 x 8.000 x 16.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1U1947-8 1 SE\_/ 33 3.79 3.66 3.95 270.00 122.471.000 x 6.500 x 152.500Dozer Blade Support 0.813
D6 H Semi-U1CH 2NH 4PH 8AH 8BHSerial Number:
9W1878 2 DB|> 8 2.88 6.00 6.00 92.40 41.9180.750 x 10.000 x 48.250Center 0.750 x 2.5
6Y3840 2 DB|> 8 2.88 6.00 6.00 123.10 55.8481.000 x 10.000 x 48.250Heavy Duty Center 0.750 x 2.5
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
D6 K Power Angle Tilt XL & LGP2401520 3063006Serial Number:
4T8940 2 DB|| 8 2.50 6.00 6.00 59.90 27.1780.625 x 8.000 x 47.000Center 0.750 x 2.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 23©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D6 K Power Angle Tilt XL & LGP2401500 3063004Serial Number:
8E9377 2 DB|| 7 2.75 6.00 6.00 52.90 24.0070.625 x 8.000 x 41.500Center 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D6 K Foldable Power Angle Tilt XL & LGP2898448Serial Number:
8E9377 1 DB|| 7 2.75 6.00 6.00 52.90 24.0070.625 x 8.000 x 41.500Center 0.750 x 2.5
2944519 1 DB|/ 0.625 x 8.000 x Dozer Foldable Center
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
3000168 1 DB/\ 0.625 x 8.000 x Dozer Foldable Side End Bit
D6 K Foldable Power Angle Tilt XL & LGP2971700Serial Number:
4T8940 1 DB|| 8 2.50 6.00 6.00 59.90 27.1780.625 x 8.000 x 47.000Center 0.750 x 2.5
2971705 1 DB|/ 5 50.625 x 8.000 x Dozer Foldable Center 0.750 x 2.25
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
2971699 1 DB/\ 7 70.625 x 8.000 x Dozer Foldable Side End Bit 0.750 x 2.5
D6 K K2 Power Angle Tilt XL & LGP3250000Serial Number:
8E7245 2 DB|| 9 2.70 6.00 6.00 68.10 30.8990.625 x 8.000 x 53.400Center 0.750 x 2.25
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D6 K2 Foldable Power Angle Tilt XL & LGP3710749Serial Number:
3428851 1 7 3.92 6.00 6.00 68.00 30.840.750 x 8.000 x 43.835 0.750
3710758 1 DB|/ 50.750 x 8.000 x Dozer Foldable Center 0.750
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
3000168 1 DB/\ 0.625 x 8.000 x Dozer Foldable Side End Bit
D6 K2 Power Angle Tilt XL & LGP3486300Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 24©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3428851 2 DB|| 7 3.92 6.00 6.00 68.00 30.840.750 x 8.000 x 43.835Center 0.750
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
D6 K2 Foldable Power Angle Tilt XL & LGP3710779Serial Number:
8E7245 1 DB|| 9 2.70 6.00 6.00 68.10 30.8990.625 x 8.000 x 53.400Center 0.750 x 2.25
3710786 1 DB|/ 6 60.625 x 8.000 x Dozer Foldable Center 0.750 x 2.25
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
2971699 1 DB/\ 7 70.625 x 8.000 x Dozer Foldable Side End Bit 0.750 x 2.5
D6 M N Semi-U2SP 6GP ECA SGDSerial Number:
4T6659 1 DB|| 7 2.75 6.00 6.00 64.40 29.2170.750 x 8.000 x 41.500Center 0.750 x 2.5
9U8057 2 DB|> 4 3.34 6.00 6.00 37.40 16.9640.750 x 8.000 x 24.688End 0.750 x 2.5
1406787 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit RH 0.750 x 2.5
1406788 1 EBHC 4 3.88 3.00 3.00 40.40 18.3340.875 x 9.625 x 21.000Hot Cup End Bit LH 0.750 x 2.5
4T5407 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit RH 0.750 x 2.5
4T5408 1 EBC 4 3.88 3.00 3.00 54.00 24.4941.000 x 10.000 x 21.000Cast End Bit LH 0.750 x 2.5
3G4285 2 DB|| 4 3.88 3.00 3.00 25.80 11.7040.750 x 8.000 x 16.750Level Cut End Bit LH/RH 0.750 x 2.5
8E9379 1 DB/| 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit RH 0.750 x 2.5
8E9378 1 DB|\ 4 3.88 3.00 3.00 37.00 16.7841.000 x 8.000 x 18.500Level Cut End Bit LH 0.750 x 2.5
D6 R Semi-U1TP 3FP 1WP 3RP 4AP 8SP BHMSerial Number:
9W1878 2 DB|> 8 2.88 6.00 6.00 92.40 41.9180.750 x 10.000 x 48.250Center 0.750 x 2.5
6Y3840 2 DB|> 8 2.88 6.00 6.00 123.10 55.8481.000 x 10.000 x 48.250Heavy Duty Center 0.750 x 2.5
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
6Y1390-8 1 SE|| 16 3.50 6.00 6.00 203.50 92.311.000 x 7.500 x 97.000Dozer Blade Support 0.813
8E5205-8 2 SE\\ 6 4.30 3.19 3.19 29.60 13.431.000 x 7.500 x 16.509Dozer End Bit Support 0.8134.30 3.94 3.66 ...2nd Row0.813
D6 R Semi-U Custom Wide9BP 1WP (BLADE PART NO 4Z9230 OR 1430499)Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 25©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1060956 2 DB|> 9 2.88 6.00 6.00 104.30 47.3190.750 x 10.000 x 54.375Center 0.750 x 2.5
2296599 2 DB|> 9 2.88 6.00 6.00 139.10 63.0991.000 x 10.000 x 54.375Heavy Duty Center 0.750 x 2.5
6Y4411 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit RH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
6Y4410 1 EBC 6 2.24 3.19 3.19 60.70 27.5330.750 x 12.493 x 19.985Cast End Bit LH 0.750 x 2.53 2.24 3.94 3.66 ...2nd Row0.750 x 2.5
9W1875 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit RH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W1876 1 EBC 6 2.25 3.19 3.19 57.80 26.2231.000 x 11.875 x 18.500Cast End Bit LH 0.750 x 2.53 2.25 3.88 3.63 ...2nd Row0.750 x 2.5
9W8874 1 DB/| 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
9W8875 1 DB|\ 6 2.25 3.19 3.19 41.70 18.9131.000 x 10.000 x 18.375Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228618 1 DB/| 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit RH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
1228617 1 DB|\ 6 2.25 3.19 3.19 60.80 27.5831.375 x 10.000 x 18.000Level Cut End Bit LH 0.750 x 2.53 2.25 3.94 3.63 ...2nd Row0.750 x 2.5
4Z9239-8 1 SE|| 18 3.50 6.00 6.00 228.70 103.741.000 x 7.500 x 109.000Dozer Blade Support 0.813
8E5205-8 2 SE\\ 6 4.30 3.19 3.19 29.60 13.431.000 x 7.500 x 16.509Dozer End Bit Support 0.8134.30 3.94 3.66 ...2nd Row0.813
D7 Angle17C5001-P 06A 35D 84D 18E 06ESerial Number:
4T2949 2 DB|| 15 1.94 4.00 4.00 115.10 52.21150.750 x 10.000 x 59.875Center 0.750 x 2.75
4T2863 2 DB|| 15 1.94 4.00 4.00 155.40 70.49151.000 x 10.000 x 59.875Heavy Duty Center 0.750 x 2.75
3G8313 1 EBHC 7 2.00 4.00 4.00 55.20 25.0431.125 x 11.875 x 17.625Hot Cup End Bit RH 0.750 x 4.754 2.00 3.00 3.00 ...2nd Row0.750 x 2.75
3G8314 1 EBHC 7 2.00 4.00 4.00 55.20 25.0431.125 x 11.875 x 17.625Hot Cup End Bit LH 0.750 x 4.754 2.00 3.00 3.00 ...2nd Row0.750 x 2.75
4T6667 1 DB/| 7 2.00 4.00 4.00 37.50 17.0131.000 x 10.000 x 16.000Level Cut End Bit RH 0.750 x 4.754 2.00 3.00 3.00 ...2nd Row0.750 x 2.75
4T6668 1 DB|\ 7 2.00 4.00 4.00 37.50 17.0131.000 x 10.000 x 16.000Level Cut End Bit LH 0.750 x 4.754 2.00 3.00 3.00 ...2nd Row0.750 x 2.75
D7 G Angle13F 22F 30F 72F 13HSerial Number:
4T2948 3 DB|| 7 2.94 6.00 6.00 81.20 36.8370.750 x 10.000 x 41.875Center 0.750 x 2.75
4T2989 3 DB|| 7 2.94 6.00 6.00 108.30 49.1271.000 x 10.000 x 41.875Heavy Duty Center 0.750 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 26©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W9796 3 DB|| 7 2.88 6.00 6.00 110.20 49.9971.000 x 11.000 x 41.75011" Center 0.750 x 2.75
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D7 H R Angle4EB 3CC 4ZCSerial Number:
4T3901 3 DB|| 7 3.50 6.00 6.00 83.20 37.7470.750 x 10.000 x 43.000Center 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
7T6589 3 DB|| 7 3.50 6.00 6.00 112.90 51.2171.000 x 11.000 x 43.00011" Center 0.875 x 2.75
1359778 3 DB|| 7 3.50 6.00 6.00 170.00 77.1171.375 x 11.000 x 43.000Heavy Duty 11" Center 0.875 x 2.75
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 27©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6337-9 1 SE\_/ 35 4.63 3.00 3.00 429.40 194.771.125 x 8.500 x 163.000Dozer Blade Support 0.938
D7 Straight17C1-5000 05A 84C 34D 83D 02E 17ESerial Number:
4T2954 1 DB|| 23 1.94 4.00 4.00 176.00 79.83230.750 x 10.000 x 91.875Center 0.750 x 2.5
4T2864 1 DB|| 23 1.94 4.00 4.00 239.00 108.41231.000 x 10.000 x 91.875Heavy Duty Center 0.750 x 2.5
3G8311 1 EBHC 7 2.00 4.00 4.00 55.00 24.9531.125 x 12.000 x 18.125Hot Cup End Bit RH 0.750 x 4.754 2.00 4.00 4.00 ...2nd Row0.750 x 4.75
3G8312 1 EBHC 7 2.00 4.00 4.00 55.00 24.9531.125 x 12.000 x 18.125Hot Cup End Bit LH 0.750 x 4.754 2.00 4.00 4.00 ...2nd Row0.750 x 4.75
4T6671 1 DB/| 7 1.88 4.00 4.00 38.50 17.4631.000 x 10.000 x 15.875Level Cut End Bit RH 0.750 x 2.754 1.88 4.00 4.00 ...2nd Row0.750 x 2.75
4T6672 2 DB|\ 7 1.88 4.00 4.00 38.50 17.4631.000 x 10.000 x 15.875Level Cut End Bit LH 0.750 x 2.754 1.88 4.00 4.00 ...2nd Row0.750 x 2.75
D7 Straight23F 31F 59F 14HSerial Number:
4T2946 1 DB|| 7 3.94 6.00 6.00 85.10 38.6070.750 x 10.000 x 43.875Center 0.750 x 2.5
4T2945 2 DB|| 5 1.94 6.00 6.00 54.00 24.4950.750 x 10.000 x 27.875End 0.750 x 2.5
4T2990 1 DB|| 7 3.94 6.00 6.00 115.00 52.1671.000 x 10.000 x 43.875Heavy Duty Center 0.750 x 2.5
4T2991 2 DB|| 5 1.94 6.00 6.00 72.90 33.0751.000 x 10.000 x 27.875Heavy Duty End 0.750 x 2.5
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D7 G Straight53J 49K 60K 64K S7GSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 28©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T2921 1 DB|| 7 2.69 6.00 6.00 80.90 36.7070.750 x 10.000 x 41.875Center 0.875 x 2.5
4T2922 2 DB|| 5 2.69 6.00 6.00 57.70 26.1750.750 x 10.000 x 29.875End 0.875 x 2.5
4T2993 1 DB|| 7 2.94 6.00 6.00 107.80 48.9071.000 x 10.000 x 41.875Center 0.875 x 2.5
4T2992 2 DB|| 5 2.94 6.00 6.00 76.90 34.8851.000 x 10.000 x 29.875End 0.875 x 2.5
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W9794 1 DB|| 7 2.94 6.00 6.00 109.90 49.8571.000 x 11.000 x 41.87511" Center 0.875 x 2.5
9W9795 2 DB|| 5 2.94 6.00 6.00 78.50 35.6151.000 x 11.000 x 29.87511" End 0.875 x 2.5
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D7 H R Straight6KB 8ZB 4XC 8NH J8L CDCSerial Number:
4T5318 3 DB|| 6 2.63 6.00 6.00 68.10 30.8960.750 x 10.000 x 35.250Center 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 29©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
7T6678 3 DB|| 6 2.63 6.00 6.00 93.50 42.4161.000 x 11.000 x 35.25011" Center 0.875 x 2.75
1073363 3 DB|| 6 2.63 6.00 6.00 145.00 65.7761.375 x 11.000 x 35.250Heavy Duty 11" Center 0.875 x 2.75
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
6Y5701-9 1 SE\_/ 32 6.15 3.00 3.00 373.30 169.331.125 x 8.500 x 142.806Dozer Blade Support 0.938
D7 H R Straight LGP6JB 3GH 4FG 4XH 5GHSerial Number:
4T3901 3 DB|| 7 3.50 6.00 6.00 83.20 37.7470.750 x 10.000 x 43.000Center 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 30©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7T6589 3 DB|| 7 3.50 6.00 6.00 112.90 51.2171.000 x 11.000 x 43.00011" Center 0.875 x 2.75
1359778 3 DB|| 7 3.50 6.00 6.00 170.00 77.1171.375 x 11.000 x 43.000Heavy Duty 11" Center 0.875 x 2.75
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D7 H R XR Straight LGP2RP 8RH 5SP 9KP J4L CDNSerial Number:
1285883 3 DB|| 7 3.80 6.00 6.00 84.00 38.1070.750 x 10.000 x 43.625Center 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1356537 3 DB|| 7 3.81 6.00 6.00 114.70 52.0371.000 x 11.000 x 43.62211" Center 0.875 x 2.75
1457846 3 DB|| 7 3.80 6.00 6.00 172.00 78.0271.375 x 11.000 x 43.625Heavy Duty 11" Center 0.875 x 2.75
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 31©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1356536-9 1 SE|| 35 5.13 3.00 3.00 432.00 195.951.125 x 8.500 x 165.630Dozer Blade Support 0.938...2nd Row0.938
D7 Full-U42GSerial Number:
4T2955 1 DB<> 9 2.75 6.00 6.00 98.80 44.8190.750 x 10.000 x 53.500Center 0.750 x 2.5
4T2952 2 DB|| 5 3.75 6.00 6.00 61.10 27.7150.750 x 10.000 x 31.500Center 0.750 x 2.5
4T2890 1 DB<> 9 2.75 6.00 6.00 143.00 64.8691.000 x 10.000 x 53.500Heavy Duty Center 0.750 x 2.5
4T2985 2 DB|| 5 3.75 6.00 6.00 81.60 37.0151.000 x 10.000 x 31.500Heavy Duty Center 0.750 x 2.5
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D7 G Full-U85D 61K 94RSerial Number:
4T2917 1 DB<> 9 2.69 6.00 6.00 101.10 45.8690.750 x 10.000 x 53.375Center 0.875 x 2.5
4T2916 2 DB|| 5 4.13 6.00 6.00 62.40 28.3050.750 x 10.000 x 32.250End 0.875 x 2.5
4T3421 1 DB<> 9 2.69 6.00 6.00 135.40 61.4291.000 x 10.000 x 53.375Center 0.875 x 2.5
4T3420 2 DB|| 5 4.06 6.00 6.00 83.90 38.0651.000 x 10.000 x 32.125End 0.875 x 2.5
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 32©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W9793 1 DB<> 9 2.69 6.00 6.00 136.50 61.9291.000 x 11.000 x 53.37511" Center 0.875 x 2.5
9W9792 2 DB|| 5 4.06 6.00 6.00 93.00 42.1851.000 x 11.000 x 32.12511" End 0.875 x 2.5
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D7 H R Full-U5SB 9JB 7AC 8MH JIL CDLSerial Number:
4T7110 2 DB|> 6 5.50 6.00 6.00 74.20 33.6660.750 x 10.000 x 38.938Center 0.875 x 2.75
4T7109 2 DB|| 4 2.19 6.00 6.00 43.20 19.6040.750 x 10.000 x 22.375End 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
7T6591 2 DB|> 6 5.50 6.00 6.00 101.90 46.2261.000 x 11.000 x 38.93811" Center 0.875 x 2.75
7T6592 2 DB|| 4 2.19 6.00 6.00 60.00 27.2241.000 x 11.000 x 22.37511" End 0.875 x 2.75
1359627 2 DB|> 6 5.50 6.00 6.00 152.00 68.9561.375 x 11.000 x 38.938Heavy Duty 11" Center 0.875 x 2.75
1359626 2 DB|| 4 2.19 6.00 6.00 89.00 40.3741.375 x 11.000 x 22.375Heavy Duty 11" End 0.875 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 33©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1U1440-9 1 SE|| 12 3.44 6.00 6.00 205.00 92.991.125 x 8.500 x 78.125Dozer Blade Support 0.938
6Y5700-9 2 SE\\ 11 4.31 6.00 6.00 100.10 45.401.125 x 8.500 x 40.125Dozer Blade/End Bit Support 0.938
D7 H R XR Semi-U4DB 2FC 2JH 1JP 8LH CDT J6L BHTSerial Number:
4T5318 1 DB|| 6 2.63 6.00 6.00 68.10 30.8960.750 x 10.000 x 35.250Center 0.875 x 2.75
1U1192 2 DB|> 6 3.13 6.00 6.00 68.30 30.9860.750 x 10.000 x 35.938End 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
7T6678 1 DB|| 6 2.63 6.00 6.00 93.50 42.4161.000 x 11.000 x 35.25011" Center 0.875 x 2.75
7T6936 2 DB|> 6 3.13 6.00 6.00 92.80 42.0961.000 x 11.000 x 35.93811" End 0.875 x 2.75
1073363 1 DB|| 6 2.63 6.00 6.00 145.00 65.7761.375 x 11.000 x 35.250Heavy Duty 11" Center 0.875 x 2.75
1073362 2 DB|> 6 2.63 6.00 6.00 145.00 65.7761.375 x 11.000 x 35.750Heavy Duty 11" End 0.875 x 2.75
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 34©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G5352-9 1 SE|| 18 2.88 6.00 6.00 283.00 128.371.125 x 8.500 x 107.750Dozer Blade Support 0.938
6I8380-9 2 SE// 7 4.95 4.00 4.00 42.60 19.321.125 x 8.500 x 18.500Dozer End Bit Support 0.9384.95 3.00 3.00 ...2nd Row0.938
D8 Angle07A 18C 33D 72D 87D 99D 07E 22ESerial Number:
4T2943 2 DB|| 16 1.94 4.00 4.00 117.00 53.07160.750 x 10.000 x 63.875Center 0.750 x 3.25
4T2888 2 DB|| 16 1.94 4.00 4.00 165.80 75.21161.000 x 10.000 x 63.875Heavy Duty Center 0.750 x 3.25
3G8313 1 EBHC 7 2.00 4.00 4.00 55.20 25.0431.125 x 11.875 x 17.625Hot Cup End Bit RH 0.750 x 4.754 2.00 3.00 3.00 ...2nd Row0.750 x 4.75
3G8314 1 EBHC 7 2.00 4.00 4.00 55.20 25.0431.125 x 11.875 x 17.625Hot Cup End Bit LH 0.750 x 4.754 2.00 3.00 3.00 ...2nd Row0.750 x 4.75
4T6667 1 DB/| 7 2.00 4.00 4.00 37.50 17.0131.000 x 10.000 x 16.000Level Cut End Bit RH 0.750 x 4.754 2.00 3.00 3.00 ...2nd Row0.750 x 4.75
4T6668 1 DB|\ 7 2.00 4.00 4.00 37.50 17.0131.000 x 10.000 x 16.000Level Cut End Bit LH 0.750 x 4.754 2.00 3.00 3.00 ...2nd Row0.750 x 4.75
D8 Cushion Dozer71F 77GSerial Number:
4T2867 1 DB|| 13 4.19 6.00 6.00 209.80 95.16131.000 x 10.000 x 80.375Center 0.875 x 3
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D8 Ripper Dozer43KSerial Number:
4T3418 2 DB|| 10 3.13 6.00 6.00 155.10 70.35101.000 x 10.000 x 60.250Center 0.875 x 3
4T6298 2 DB|| 10 3.13 6.00 6.00 256.70 116.44101.625 x 10.000 x 60.250Heavy Duty Center 0.875 x 3
1073476 2 DB|| 10 3.13 6.00 6.00 275.00 124.74101.750 x 10.000 x 60.250Extra Heavy Duty Center 0.875 x 3
3G8299 1 EBHC 7 2.50 4.00 4.00 76.40 34.6531.250 x 13.000 x 21.625Hot Cup End Bit RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 35©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8300 1 EBHC 7 2.50 4.00 4.00 76.40 34.6531.250 x 13.000 x 21.625Hot Cup End Bit LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8277 1 EBHC 7 2.50 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8278 1 EBHC 7 2.50 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
4T6669 1 DB/| 7 2.44 4.00 4.00 34.80 15.7931.000 x 10.000 x 15.375Level Cut End Bit RH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
4T6670 1 DB|\ 7 2.44 4.00 4.00 34.80 15.7931.000 x 10.000 x 15.375Level Cut End Bit LH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
7J2975 1 DB/| 7 2.44 4.00 4.00 57.00 25.8531.625 x 10.000 x 15.375Level Cut End Bit RH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
7J2976 1 DB|\ 7 2.44 4.00 4.00 57.00 25.8531.625 x 10.000 x 15.375Level Cut End Bit LH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
D8 Semi-U08A 12C 18C 32D 03E 86D 44C1-1192Serial Number:
4T2944 2 DB|| 13 1.94 4.00 4.00 99.70 45.22130.750 x 10.000 x 51.875Center 0.750 x 3.25
4T2860 2 DB|| 13 1.94 4.00 4.00 136.00 61.69131.000 x 10.000 x 51.875Heavy Duty Center 0.750 x 3.25
3G8311 1 EBHC 7 2.00 4.00 4.00 55.00 24.9531.125 x 12.000 x 18.125Hot Cup End Bit RH 0.750 x 4.754 2.00 4.00 4.00 ...2nd Row0.750 x 4.75
3G8312 1 EBHC 7 2.00 4.00 4.00 55.00 24.9531.125 x 12.000 x 18.125Hot Cup End Bit LH 0.750 x 4.754 2.00 4.00 4.00 ...2nd Row0.750 x 4.75
4T6671 1 DB/| 7 1.88 4.00 4.00 38.50 17.4631.000 x 10.000 x 15.875Level Cut End Bit RH 0.750 x 4.754 1.88 4.00 4.00 ...2nd Row0.750 x 2.75
4T6672 1 DB|\ 7 1.88 4.00 4.00 38.50 17.4631.000 x 10.000 x 15.875Level Cut End Bit LH 0.750 x 4.754 1.88 4.00 4.00 ...2nd Row0.750 x 2.75
D8 Semi-U44C1193-UP 73DSerial Number:
4T2862 2 DB|| 14 1.94 4.00 4.00 145.00 65.77141.000 x 10.000 x 55.875Center 0.750 x 3.25
3G8311 1 EBHC 7 2.00 4.00 4.00 55.00 24.9531.125 x 12.000 x 18.125Hot Cup End Bit RH 0.750 x 4.754 2.00 4.00 4.00 ...2nd Row0.750 x 4.75
3G8312 1 EBHC 7 2.00 4.00 4.00 55.00 24.9531.125 x 12.000 x 18.125Hot Cup End Bit LH 0.750 x 4.754 2.00 4.00 4.00 ...2nd Row0.750 x 4.75
4T6671 1 DB/| 7 1.88 4.00 4.00 38.50 17.4631.000 x 10.000 x 15.875Level Cut End Bit RH 0.750 x 4.754 1.88 4.00 4.00 ...2nd Row0.750 x 2.75
4T6672 1 DB|\ 7 1.88 4.00 4.00 38.50 17.4631.000 x 10.000 x 15.875Level Cut End Bit LH 0.750 x 4.754 1.88 4.00 4.00 ...2nd Row0.750 x 2.75
D8 Full-U11C 74D 88D 24ESerial Number:
4T3419 1 DB|> 12 1.88 4.00 4.00 118.60 53.80121.000 x 10.000 x 47.750Center 0.750 x 3.25
4T2861 2 DB|| 9 1.88 4.00 4.00 102.00 46.2791.000 x 10.000 x 35.750End 0.750 x 3.25
3G8313 1 EBHC 7 2.00 4.00 4.00 55.20 25.0431.125 x 11.875 x 17.625Hot Cup End Bit RH 0.750 x 3.254 2.00 3.00 3.00 ...2nd Row0.750 x 3.25
3G8314 1 EBHC 7 2.00 4.00 4.00 55.20 25.0431.125 x 11.875 x 17.625Hot Cup End Bit LH 0.750 x 3.254 2.00 3.00 3.00 ...2nd Row0.750 x 3.25
4T6667 1 DB/| 7 2.00 4.00 4.00 37.50 17.0131.000 x 10.000 x 16.000Level Cut End Bit RH 0.750 x 3.254 2.00 3.00 3.00 ...2nd Row0.750 x 3.25
4T6668 1 DB|\ 7 2.00 4.00 4.00 37.50 17.0131.000 x 10.000 x 16.000Level Cut End Bit LH 0.750 x 3.254 2.00 3.00 3.00 ...2nd Row0.750 x 3.25
D8 H Angle28E1-11125Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 36©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6532 4 DB|| 6 2.94 6.00 6.00 92.30 41.8761.000 x 10.000 x 35.875Center 0.875 x 3
7J2972 4 DB|| 6 2.88 6.00 6.00 152.70 69.2661.625 x 10.000 x 35.750Heavy Duty Center 0.875 x 3
1073474 4 DB|| 6 2.88 6.00 6.00 163.00 73.9461.750 x 10.000 x 35.750Extra Heavy Duty Center 0.875 x 3
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
6Y6761 4 DB|| 6 2.88 6.00 6.00 141.70 64.2761.375 x 11.000 x 35.75011" Center 0.875 x 3
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
7T4348 4 DB|| 6 2.88 6.00 6.00 202.70 91.9461.625 x 13.000 x 35.750Wide Center (Offset Holes) 0.875 x 3
3G8285EWL 1 EBHC 7 2.88 4.00 4.00 124.00 56.2531.625 x 15.110 x 21.572End Bit (Long Side) RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8286EWL 1 EBHC 7 2.88 4.00 4.00 124.00 56.2531.625 x 15.110 x 21.572End Bit (Long Side) LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.000End Bit (Short Side) RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.000End Bit (Short Side) LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D8 H Semi-U78C 29E 94ESerial Number:
4T6531 2 DB|| 10 2.94 6.00 6.00 154.10 69.90101.000 x 10.000 x 59.875Center 0.875 x 3
4T6299 2 DB|| 10 2.88 6.00 6.00 256.90 116.53101.625 x 10.000 x 59.875Heavy Duty Center 0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 37©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1073477 2 DB|| 10 2.88 6.00 6.00 274.00 124.28101.750 x 10.000 x 59.750Extra Heavy Duty Center 0.875 x 3
3G8299 1 EBHC 7 2.50 4.00 4.00 76.40 34.6531.250 x 13.000 x 21.625Hot Cup End Bit RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8300 1 EBHC 7 2.50 4.00 4.00 76.40 34.6531.250 x 13.000 x 21.625Hot Cup End Bit LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8277 1 EBHC 7 2.50 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8278 1 EBHC 7 2.50 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
4T6669 1 DB/| 7 2.44 4.00 4.00 34.80 15.7931.000 x 10.000 x 15.375Level Cut End Bit RH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
4T6670 1 DB|\ 7 2.44 4.00 4.00 34.80 15.7931.000 x 10.000 x 15.375Level Cut End Bit LH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
7J2975 1 DB/| 7 2.44 4.00 4.00 57.00 25.8531.625 x 10.000 x 15.375Level Cut End Bit RH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
7J2976 1 DB|\ 7 2.44 4.00 4.00 57.00 25.8531.625 x 10.000 x 15.375Level Cut End Bit LH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
6Y6764 2 DB|| 10 2.94 6.00 6.00 242.60 110.04101.375 x 11.000 x 59.87511" Center 0.875 x 3
3G8277X11 1 EBHC 7 2.50 4.00 4.00 104.00 47.1731.625 x 13.000 x 21.62511" Hot Cupped End Bit RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8278X11 1 EBHC 7 2.50 4.00 4.00 104.00 47.1731.625 x 13.000 x 21.62511" Hot Cupped End Bit LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
6Y5776 2 DB|| 10 2.94 6.00 6.00 339.50 153.99101.625 x 13.000 x 59.875Wide Center (Offset Holes) 0.875 x 3
3G8277EWL 1 EBHC 7 2.50 4.00 4.00 120.00 54.4331.625 x 15.000 x 22.500End Bit (Long Side) RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8278EWL 1 EBHC 7 2.50 4.00 4.00 120.00 54.4331.625 x 15.000 x 22.500End Bit (Long Side) LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8277X11 1 EBHC 7 2.50 4.00 4.00 104.00 47.1731.625 x 13.000 x 21.625End Bit (Short Side) RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8278X11 1 EBHC 7 2.50 4.00 4.00 104.00 47.1731.625 x 13.000 x 21.625End Bit (Short Side) LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
D8 H Semi-U69E 14J 44K 95S 80V 47KSerial Number:
4T3418 2 DB|| 10 3.13 6.00 6.00 155.10 70.35101.000 x 10.000 x 60.250Center 0.875 x 3
4T6298 2 DB|| 10 3.13 6.00 6.00 256.70 116.44101.625 x 10.000 x 60.250Heavy Duty Center 0.875 x 3
1073476 2 DB|| 10 3.13 6.00 6.00 275.00 124.74101.750 x 10.000 x 60.250Extra Heavy Duty Center 0.875 x 3
4T6669 1 DB/| 7 2.44 4.00 4.00 34.80 15.7931.000 x 10.000 x 15.375Level Cut End Bit RH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
4T6670 1 DB|\ 7 2.44 4.00 4.00 34.80 15.7931.000 x 10.000 x 15.375Level Cut End Bit LH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
7J2975 1 DB/| 7 2.44 4.00 4.00 57.00 25.8531.625 x 10.000 x 15.375Level Cut End Bit RH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
7J2976 1 DB|\ 7 2.44 4.00 4.00 57.00 25.8531.625 x 10.000 x 15.375Level Cut End Bit LH 0.875 x 34 2.44 3.00 3.00 ...2nd Row0.875 x 3
3G8299 1 EBHC 7 2.50 4.00 4.00 76.40 34.6531.250 x 13.000 x 21.625Hot Cup End Bit RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8300 1 EBHC 7 2.50 4.00 4.00 76.40 34.6531.250 x 13.000 x 21.625Hot Cup End Bit LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 38©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8277 1 EBHC 7 2.50 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8278 1 EBHC 7 2.50 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
6Y6763 1 DB|| 10 3.13 6.00 6.00 244.20 110.77101.375 x 11.000 x 60.25011" Center 0.875 x 3
3G8277X11 1 EBHC 7 2.50 4.00 4.00 104.00 47.1731.625 x 13.000 x 21.62511" Hot Cupped End Bit RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8278X11 1 EBHC 7 2.50 4.00 4.00 104.00 47.1731.625 x 13.000 x 21.62511" Hot Cupped End Bit LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
6Y5777 1 DB|| 10 3.13 6.00 6.00 341.70 154.99101.625 x 13.000 x 60.250Wide Center (Offset Holes) 0.875 x 3
3G8277EWL 1 EBHC 7 2.50 4.00 4.00 120.00 54.4331.625 x 15.000 x 22.500End Bit (Long Side) RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8278EWL 1 EBHC 7 2.50 4.00 4.00 120.00 54.4331.625 x 15.000 x 22.500End Bit (Long Side) LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8277X11 1 EBHC 7 2.50 4.00 4.00 104.00 47.1731.625 x 13.000 x 21.625End Bit (Short Side) RH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
3G8278X11 1 EBHC 7 2.50 4.00 4.00 104.00 47.1731.625 x 13.000 x 21.625End Bit (Short Side) LH 0.875 x 34 2.50 3.00 3.00 ...2nd Row0.875 x 3
D8 H Full-U30E 73E 29JSerial Number:
4T6513 1 DB<> 10 2.94 6.00 6.00 150.30 68.17101.000 x 10.000 x 59.875Center 0.875 x 3
4T6532 2 DB|| 6 2.94 6.00 6.00 92.30 41.8761.000 x 10.000 x 35.875End 0.875 x 3
4T6300 1 DB<> 10 2.94 6.00 6.00 250.50 113.62101.625 x 10.000 x 59.875Heavy Duty Center 0.875 x 3
4T6296 2 DB|| 6 2.88 6.00 6.00 152.30 69.081.625 x 10.000 x 35.750Heavy Duty End 0.875 x 3
1073478 1 DB<> 10 2.94 6.00 6.00 269.00 122.02101.750 x 10.000 x 59.875Extra Heavy Duty Center 0.875 x 3
1073474 2 DB|| 6 2.88 6.00 6.00 163.00 73.9461.750 x 10.000 x 35.750Extra Heavy Duty End 0.875 x 3
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
6Y6765 1 DB<> 10 2.94 6.00 6.00 236.60 107.32101.375 x 11.000 x 59.87511" Center 0.875 x 3
6Y6761 2 DB|| 6 2.88 6.00 6.00 141.70 64.2761.375 x 11.000 x 35.75011" End 0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 39©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
7T4355 1 DB<> 10 2.94 6.00 6.00 330.80 150.05101.625 x 13.000 x 59.875Wide Center (Offset Holes) 0.875 x 3
7T4348 2 DB|| 6 2.88 6.00 6.00 202.70 91.9461.625 x 13.000 x 35.750Wide End (Offset Holes) 0.875 x 3
3G8285EWL 1 EBHC 7 2.88 4.00 4.00 124.00 56.2531.625 x 15.110 x 21.572End Bit (Long Side) RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8286EWL 1 EBHC 7 2.88 4.00 4.00 124.00 56.2531.625 x 15.110 x 21.572End Bit (Long Side) LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.000End Bit (Short Side) RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.000End Bit (Short Side) LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D8 H Full-U20F 45K 48KSerial Number:
4T6513 1 DB<> 10 2.94 6.00 6.00 150.30 68.17101.000 x 10.000 x 59.875Center 0.875 x 3
4T6512 2 DB|| 6 3.19 6.00 6.00 94.90 43.0561.000 x 10.000 x 36.375End 0.875 x 3
4T6300 1 DB<> 10 2.94 6.00 6.00 250.50 113.62101.625 x 10.000 x 59.875Heavy Duty Center 0.875 x 3
4T6297 2 DB|| 6 3.13 6.00 6.00 154.50 70.0861.625 x 10.000 x 36.250Heavy Duty End 0.875 x 3
1073478 1 DB<> 10 2.94 6.00 6.00 269.00 122.02101.750 x 10.000 x 59.875Extra Heavy Duty Center 0.875 x 3
1073475 2 DB|| 6 3.13 6.00 6.00 166.00 75.3061.750 x 10.000 x 36.250Extra Heavy Duty End 0.875 x 3
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 40©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6Y6765 1 DB<> 10 2.94 6.00 6.00 236.60 107.32101.375 x 11.000 x 59.87511" Center 0.875 x 3
6Y6762 2 DB|| 6 3.19 6.00 6.00 147.40 66.8661.375 x 11.000 x 36.37511" End 0.875 x 3
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.00011" Hot Cupped End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050575 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050574 1 EBLC 7 2.88 4.00 4.00 63.00 28.5831.375 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050577 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
1050576 1 EBLC 7 2.88 4.00 4.00 79.70 36.1531.750 x 10.500 x 18.00011" Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
7T4355 1 DB<> 10 2.94 6.00 6.00 330.80 150.05101.625 x 13.000 x 59.875Wide Center (Offset Holes) 0.875 x 3
7T4354 2 DB|| 6 3.19 6.00 6.00 225.50 102.2961.750 x 13.000 x 36.375Wide End (Offset Holes) 0.875 x 3
3G8285EWL 1 EBHC 7 2.88 4.00 4.00 124.00 56.2531.625 x 15.110 x 21.572End Bit (Long Side) RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8286EWL 1 EBHC 7 2.88 4.00 4.00 124.00 56.2531.625 x 15.110 x 21.572End Bit (Long Side) LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6199 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.000End Bit (Short Side) RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
9W6198 1 EBHC 7 2.88 4.00 4.00 95.20 43.1831.375 x 13.000 x 24.000End Bit (Short Side) LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
D8 K Angle28E11126-UP 93E 14F 77CSerial Number:
4T2994 3 DB|| 8 2.88 6.00 6.00 122.20 55.4381.000 x 10.000 x 47.750Center 1.000 x 3.25
4T3447 3 DB|| 8 2.88 6.00 6.00 202.10 91.6781.625 x 10.000 x 47.750Heavy Duty Center 1.000 x 3.25
1073484 3 DB|| 8 2.88 6.00 6.00 219.00 99.3481.750 x 10.000 x 47.750Extra Heavy Duty Center 1.000 x 3.25
9J1477 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit RH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
9J1478 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit LH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
3G8317 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 13.000 x 21.625Hot Cup End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
3G8318 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 12.986 x 21.553Hot Cup End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
3G8287 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
3G8288 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
4T6239 1 DB/| 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
4T6240 1 DB|\ 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
4T8089 1 DB/| 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
4T8090 1 DB|\ 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 41©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W8658 3 DB|| 8 2.88 6.00 6.00 188.10 85.3281.375 x 11.000 x 47.75011" Center 1.000 x 3.25
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
7T4351 3 DB|| 8 2.88 6.00 6.00 269.40 122.2081.625 x 13.000 x 47.750Wide Center (Offset Holes) 1.000 x 3.25
7T4091 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
7T4090 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
D8 K Semi-U29V 30W 68V 60VSerial Number:
4T2988 3 DB|| 7 2.38 6.00 6.00 104.20 47.2671.000 x 10.000 x 40.750Center 1.000 x 3.25
1U4933 3 DB|| 7 2.38 6.00 6.00 148.60 67.4071.375 x 10.000 x 40.750Heavier Center 1.000 x 3.25
4T6301 3 DB|| 7 2.31 6.00 6.00 171.70 77.8871.625 x 10.000 x 40.625Heavy Duty Center 1.000 x 3.25
1073479 3 DB|| 7 2.31 6.00 6.00 185.50 84.1471.750 x 10.000 x 40.625Extra Heavy Duty Center 1.000 x 3.25
3G8301 1 EBHC 7 2.50 4.00 4.00 76.00 34.4731.250 x 13.000 x 21.625Hot Cup End Bit RH 1.000 x 3.254 2.50 3.00 3.00 ...2nd Row1.000 x 3.25
3G8302 1 EBHC 7 2.50 4.00 4.00 76.00 34.4731.250 x 13.000 x 21.625Hot Cup End Bit LH 1.000 x 3.254 2.50 3.00 3.00 ...2nd Row1.000 x 3.25
3G8279 1 EBHC 7 2.44 4.00 4.00 79.40 36.0231.625 x 11.420 x 19.840Hot Cup End Bit RH 1.000 x 3.254 2.44 3.00 3.00 ...2nd Row1.000 x 3.25
3G8280 1 EBHC 7 2.44 4.00 4.00 79.40 36.0231.625 x 11.420 x 19.840Hot Cup End Bit LH 1.000 x 3.254 2.44 3.00 3.00 ...2nd Row1.000 x 3.25
9W8657 3 DB|| 7 2.38 6.00 6.00 160.40 72.7671.375 x 11.000 x 40.75011" Center 1.000 x 3.25
9W8651 1 EBHC 7 2.50 4.00 4.00 140.70 63.8232.000 x 15.500 x 22.00011" Hot Cupped End Bit RH 1.000 x 3.254 2.50 3.00 3.00 ...2nd Row1.000 x 3.25
9W8652 1 EBHC 7 2.50 4.00 4.00 140.70 63.8232.000 x 15.500 x 22.00011" Hot Cupped End Bit LH 1.000 x 3.254 2.50 3.00 3.00 ...2nd Row1.000 x 3.25
7T4353 1 DB|| 7 2.38 6.00 6.00 229.80 104.2471.625 x 13.000 x 40.750Wide Center (Offset Holes) 1.000 x 3.25
7T4088 1 EBHC 7 2.50 4.00 4.00 129.70 58.8332.000 x 14.875 x 20.750End Bit (Long Side) RH 1.000 x 3.254 2.50 3.00 3.00 ...2nd Row1.000 x 3.25
7T4089 1 EBHC 7 2.50 4.00 4.00 129.70 58.8332.000 x 14.875 x 20.750End Bit (Long Side) LH 1.000 x 3.254 2.50 3.00 3.00 ...2nd Row1.000 x 3.25
9W8651 1 EBHC 7 2.50 4.00 4.00 140.70 63.8232.000 x 15.500 x 22.000End Bit (Short Side) RH 1.000 x 3.254 2.50 3.00 3.00 ...2nd Row1.000 x 3.25
9W8652 1 EBHC 7 2.50 4.00 4.00 140.70 63.8232.000 x 15.500 x 22.000End Bit (Short Side) LH 1.000 x 3.254 2.50 3.00 3.00 ...2nd Row1.000 x 3.25
D8 K Full-U30V 65X 69V 34WSerial Number:
4T2986 2 DB|> 5 2.88 6.00 6.00 77.50 35.1551.000 x 10.000 x 30.625Center 1.000 x 3.25
4T2987 2 DB|| 6 3.19 6.00 6.00 94.30 42.7761.000 x 10.000 x 36.375End 1.000 x 3.25
4T6295 2 DB|> 5 2.88 6.00 6.00 127.60 57.8851.625 x 10.000 x 30.625Heavy Duty Center 1.000 x 3.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 42©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6303 2 DB|| 6 3.19 6.00 6.00 152.10 68.9961.625 x 10.000 x 36.375Heavy Duty End 1.000 x 3.25
1073473 2 DB|> 5 3.75 6.00 6.00 136.00 61.6951.750 x 10.000 x 30.625Extra Heavy Duty Center 1.000 x 3.25
1073481 2 DB|| 6 3.19 6.00 6.00 166.00 75.3061.750 x 10.000 x 36.375Extra Heavy Duty End 1.000 x 3.25
9J1477 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
9J1478 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
3G8317 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 13.000 x 21.625Hot Cup End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
3G8318 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 12.986 x 21.553Hot Cup End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
3G8287 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
3G8288 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
4T6239 1 DB/| 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
4T6240 1 DB|\ 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
4T8089 1 DB/| 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
4T8090 1 DB|\ 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
9W8656 2 DB|> 5 2.88 6.00 6.00 119.80 54.3451.375 x 11.000 x 30.62511" Center 1.000 x 3.25
9W8655 2 DB|| 6 3.19 6.00 6.00 143.30 65.0061.375 x 11.000 x 36.37511" End 1.000 x 3.25
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
7T4352 2 DB|| 6 3.19 6.00 6.00 205.30 93.1261.625 x 13.000 x 36.375Wide End (Offset Holes) 1.000 x 3.25
7T4349 1 DB<| 5 2.88 6.00 6.00 168.40 76.3851.625 x 13.000 x 30.625Wide LH End (Offset Holes) 1.000 x 3.25
7T4350 1 DB|> 5 2.88 6.00 6.00 168.40 76.3851.625 x 13.000 x 30.625Wide RH End (Offset Holes) 1.000 x 3.25
7T4091 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
7T4090 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) RH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) LH 1.000 x 3.254 2.88 3.00 3.00 ...2nd Row1.000 x 3.25
D8 L Angle05Y 41Z 27BSerial Number:
4T2988 2 DB|| 7 2.38 6.00 6.00 104.20 47.2671.000 x 10.000 x 40.750Center 1.000 x 3.5
4T2987 2 DB|| 6 3.19 6.00 6.00 94.30 42.7761.000 x 10.000 x 36.375End 1.000 x 3.5
1U4933 2 DB|| 7 2.38 6.00 6.00 148.60 67.4071.375 x 10.000 x 40.750Heavier Center 1.000 x 3.5
1U4932 2 DB|| 6 3.19 6.00 6.00 127.00 57.6161.375 x 10.000 x 36.375Heavier End 1.000 x 3.5
4T6301 2 DB|| 7 2.31 6.00 6.00 171.70 77.8871.625 x 10.000 x 40.625Heavy Duty Center 1.000 x 3.5
4T6303 2 DB|| 6 3.19 6.00 6.00 152.10 68.9961.625 x 10.000 x 36.375Heavy Duty End 1.000 x 3.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 43©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1073479 2 DB|| 7 2.31 6.00 6.00 185.50 84.1471.750 x 10.000 x 40.625Extra Heavy Duty Center 1.000 x 3.5
1073481 2 DB|| 6 3.19 6.00 6.00 166.00 75.3061.750 x 10.000 x 36.375Extra Heavy Duty End 1.000 x 3.5
9J1477 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9J1478 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8317 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 13.000 x 21.625Hot Cup End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8318 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 12.986 x 21.553Hot Cup End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8287 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8288 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T6239 1 DB/| 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T6240 1 DB|\ 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T8089 1 DB/| 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T8090 1 DB|\ 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8657 2 DB|| 7 2.38 6.00 6.00 160.40 72.7671.375 x 11.000 x 40.75011" Center 1.000 x 3.5
9W8655 2 DB|| 6 3.19 6.00 6.00 143.30 65.0031.375 x 11.000 x 36.37511" End 1.000 x 3.5
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
7T4353 2 DB|| 7 2.38 6.00 6.00 229.80 104.2471.625 x 13.000 x 40.750Wide Center (Offset Holes) 1.000 x 3.5
7T4352 2 DB|| 6 3.19 6.00 6.00 205.30 93.1261.625 x 13.000 x 36.375Wide End (Offset Holes) 1.000 x 3.5
7T4090 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
7T4091 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G7289 1 SE\_/ 40 6.00 3.00 3.00 491.00 222.711.125 x 8.500 x 190.625Dozer Blade Support 1.063
D8 L Semi-U04Y1-1939Serial Number:
4T3423 2 DB|| 6 1.88 6.00 6.00 87.30 39.6061.000 x 10.000 x 33.750Center 1.000 x 3.5
4T3417 2 DB|> 5 3.94 6.00 6.00 81.00 36.7451.000 x 10.000 x 31.875End 1.000 x 3.5
1U4930 2 DB|| 6 1.88 6.00 6.00 108.00 48.9961.375 x 10.000 x 33.750Heavier Center 1.000 x 3.5
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1251.375 x 10.000 x 31.750Heavier End 1.000 x 3.5
4T3445 2 DB|| 6 1.88 6.00 6.00 142.60 64.6861.625 x 10.000 x 33.750Heavy Duty Center 1.000 x 3.5
4T6302 2 DB|> 5 3.94 6.00 6.00 130.70 59.2851.625 x 10.000 x 31.875Heavy Duty End 1.000 x 3.5
1073482 2 DB|| 6 1.88 6.00 6.00 154.00 69.8561.750 x 10.000 x 33.750Extra Heavy Duty Center 1.000 x 3.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 44©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1073480 2 DB|> 5 3.94 6.00 6.00 143.00 64.8651.750 x 10.000 x 31.875Extra Heavy Duty End 1.000 x 3.5
9J1477 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9J1478 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8317 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 13.000 x 21.625Hot Cup End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8318 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 12.986 x 21.553Hot Cup End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8287 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8288 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T8089 1 DB/| 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T8090 1 DB|\ 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T8089 1 DB/| 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T8090 1 DB|\ 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
6Y6358 2 DB|| 6 1.88 6.00 6.00 132.90 60.2861.375 x 11.000 x 33.75011" Center 1.000 x 3.5
6Y6359 2 DB|> 5 3.94 6.00 6.00 123.10 55.8451.375 x 11.000 x 31.87511" End 1.000 x 3.5
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
7T5235 2 DB|| 6 1.88 6.00 6.00 190.10 86.2361.625 x 13.000 x 33.750Wide Center (Offset Holes) 1.000 x 3.5
7T4346 1 DB<| 5 3.94 6.00 6.00 176.70 80.1551.625 x 13.000 x 31.875Wide LH End (Offset Holes) 1.000 x 3.5
7T4345 1 DB|> 5 3.94 6.00 6.00 176.70 80.1551.625 x 13.000 x 31.875Wide RH End (Offset Holes) 1.000 x 3.5
7T4091 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
7T4090 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
D8 L Semi-U04Y1940-UPSerial Number:
4T9586 1 DB|| 11 3.31 6.00 6.00 256.80 116.48111.125 x 13.000 x 66.625Center 1.000 x 3.5
6Y5540 2 DB|> 5 2.88 6.00 6.00 117.70 53.3951.125 x 13.000 x 31.500End 1.000 x 3.5
9W4396 1 DB|| 11 3.31 6.00 6.00 316.60 143.61111.375 x 13.000 x 66.625Heavier Center 1.000 x 3.5
9W4398 2 DB|> 5 2.88 6.00 6.00 145.40 65.9551.375 x 13.000 x 31.500Heavier End 1.000 x 3.5
9W3925 1 DB|| 11 3.31 6.00 6.00 406.70 184.48111.750 x 13.000 x 66.625Extra Heavy Duty Center 1.000 x 3.5
9W3927 2 DB|> 5 2.88 6.00 6.00 186.70 84.6951.750 x 13.000 x 31.500Extra Heavy Duty End 1.000 x 3.5
8E4197 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 45©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E4196 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
3G8291 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8292 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8283 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8284 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
D8 L Full-U6Y1-1395Serial Number:
4T3422 2 DB|| 7 3.56 6.00 6.00 111.90 50.7671.000 x 10.000 x 43.125Center 1.000 x 3.5
4T3417 2 DB|> 5 3.94 6.00 6.00 81.00 36.7451.000 x 10.000 x 31.875End 1.000 x 3.5
1U4931 2 DB|| 7 3.50 6.00 6.00 155.80 70.6771.375 x 10.000 x 43.000Heavier Center 1.000 x 3.5
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1251.375 x 10.000 x 31.750Heavier End 1.000 x 3.5
4T3446 2 DB|| 7 3.50 6.00 6.00 180.20 81.7471.625 x 10.000 x 43.000Heavy Duty Center 1.000 x 3.5
4T6302 2 DB|> 5 3.94 6.00 6.00 130.70 59.2851.625 x 10.000 x 31.875Heavy Duty End 1.000 x 3.5
1073483 2 DB|| 7 3.50 6.00 6.00 196.00 88.9071.750 x 10.000 x 43.000Extra Heavy Duty Center 1.000 x 3.5
1073480 2 DB|> 5 3.94 6.00 6.00 143.00 64.8651.750 x 10.000 x 31.875Extra Heavy Duty End 1.000 x 3.5
9J1477 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9J1478 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8317 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 13.000 x 21.625Hot Cup End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8318 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 12.986 x 21.553Hot Cup End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
3G8287 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 46©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8288 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T6239 1 DB/| 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T6240 1 DB|\ 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T8089 1 DB/| 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
4T8090 1 DB|\ 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
6Y6360 2 DB|| 7 3.50 6.00 6.00 169.60 76.9371.375 x 11.000 x 43.00011" Center 1.000 x 3.5
6Y6359 2 DB|> 5 3.94 6.00 6.00 123.10 55.8451.375 x 11.000 x 31.87511" End 1.000 x 3.5
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.00011" Hot Cupped End Bit LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
7T4347 2 DB|| 7 3.50 6.00 6.00 242.80 110.1371.625 x 13.000 x 43.000Wide Center (Offset Holes) 1.000 x 3.5
7T4345 1 DB|> 5 3.94 6.00 6.00 176.70 80.1551.625 x 13.000 x 31.875Wide RH End (Offset Holes) 1.000 x 3.5
7T4346 1 DB<| 5 3.94 6.00 6.00 176.70 80.1551.625 x 13.000 x 31.875Wide LH End (Offset Holes) 1.000 x 3.5
7T4091 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
7T4090 1 EBHC 7 2.88 4.00 4.00 162.70 73.8032.250 x 15.500 x 20.750End Bit (Long Side) LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8653 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) RH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
9W8654 1 EBHC 7 2.88 4.00 4.00 156.00 70.7632.250 x 15.063 x 22.000End Bit (Short Side) LH 1.000 x 3.54 2.88 3.00 3.00 ...2nd Row1.000 x 3.5
D8 L Full-U6Y1396-UP 42Z 82MSerial Number:
4T9590 1 DB|| 14 3.63 6.00 6.00 327.80 148.69141.125 x 13.000 x 85.250Center 1.000 x 3.5
4T9587 2 DB|> 5End x 3.5
9W4397 1 DB|| 14 3.56 6.00 6.00 403.00 182.80141.375 x 13.000 x 85.125Heavier Center 1.000 x 3.5
9W4398 2 DB|> 5 2.88 6.00 6.00 145.40 65.9551.375 x 13.000 x 31.500Heavier End 1.000 x 3.5
9W3926 1 DB|| 14 3.56 6.00 6.00 514.00 233.15141.750 x 13.000 x 85.125Extra Heavy Duty Center 1.000 x 3.5
9W3927 2 DB|> 5 2.88 6.00 6.00 186.70 84.6951.750 x 13.000 x 31.500Extra Heavy Duty End 1.000 x 3.5
8E4197 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
3G8291 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8292 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8283 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 47©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8284 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
D8 N R T Angle1HH 2XP 9AH 6NH 4ZPSerial Number:
9W5432 3 DB|| 8 3.38 6.00 6.00 187.90 85.2381.125 x 13.000 x 48.750Center 1.000 x 3
9W9098 3 DB|| 8 3.38 6.00 6.00 231.60 105.0581.375 x 13.000 x 48.750Heavier Center 1.000 x 3
1122474 3 DB|| 8 3.38 6.00 6.00 300.70 136.4081.750 x 13.000 x 48.750Extra Heavy Duty Center 1.000 x 3
8E4193 1 EBC 7 3.61 4.00 4.00 110.80 50.2631.313 x 15.370 x 23.495Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4194 1 EBC 7 3.61 4.00 4.00 110.60 50.1731.313 x 15.370 x 23.495Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4537 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4538 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4193HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4194HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4537HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
8E4538HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
6Y4277 1 DB/| 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
6Y4278 1 DB|\ 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
1003139 1 DB/| 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
1003140 1 DB|\ 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
1368757 1 DB/| 7 3.61 4.00 4.00 175.28 79.512.375 x 13.000 x 23.000Level Cut End Bit RH 1.0002.36 3.25 3.25 ...2nd Row1.000
1368756 1 DB|\ 7 3.61 4.00 4.00 175.28 79.512.375 x 13.000 x 23.000Level Cut End Bit LH 1.0002.36 3.25 3.25 ...2nd Row1.000
D8 N R T AngleBHR 9ZP DZD D1E D1FSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 48©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1359373 3 DB|| 8 3.94 6.00 6.00 192.40 87.2781.125 x 13.000 x 49.875Center 1.000 x 3.25
1359628 3 DB|| 8 3.94 6.00 6.00 190.00 86.1881.375 x 13.000 x 49.875Heavier Center 1.000 x 3.25
1359629 3 DB|| 8 3.94 6.00 6.0081.750 x 13.000 x 49.875Extra Heavy Duty Center 1.000 x 3.25
8E4193 1 EBC 7 3.61 4.00 4.00 110.80 50.2631.313 x 15.370 x 23.495Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4194 1 EBC 7 3.61 4.00 4.00 110.60 50.1731.313 x 15.370 x 23.495Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4537 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4538 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4193HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4194HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4537HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
8E4538HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
6Y4277 1 DB/| 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
6Y4278 1 DB|\ 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
1003139 1 DB/| 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
1003140 1 DB|\ 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
1368757 1 DB/| 7 3.61 4.00 4.00 175.28 79.512.375 x 13.000 x 23.000Level Cut End Bit RH 1.0002.36 3.25 3.25 ...2nd Row1.000
1368756 1 DB|\ 7 3.61 4.00 4.00 175.28 79.512.375 x 13.000 x 23.000Level Cut End Bit LH 1.0002.36 3.25 3.25 ...2nd Row1.000
1473527-10 1 SE\_/ 40 5.94 3.25 3.25 641.60 291.021.250 x 10.000 x 187.500Dozer Blade Support 1.0634.00 4.00 ...2nd Row1.063
D8 N R T Semi-U1KH 2PP 2TP 3MP 3WH 1HP 6LH 9BH 9PH 2NP 05A 9TP BHW B8S DZASerial Number:
4T6381 1 DB|| 9 2.63 6.00 6.00 204.60 92.8191.125 x 13.000 x 53.250Center 1.000 x 3
6Y5540 2 DB|> 5 2.88 6.00 6.00 117.70 53.3951.125 x 13.000 x 31.500End 1.000 x 3
7T9126 1 DB|| 9 2.63 6.00 6.00 253.30 114.8991.375 x 13.000 x 53.250Heavier Center 1.000 x 3
7T9125 2 DB|> 5 2.88 6.00 6.00 145.70 66.0951.375 x 13.000 x 31.500Heavier End 1.000 x 3
1122472 1 DB|| 9 2.63 6.00 6.00 324.80 147.3391.750 x 13.000 x 53.250Extra Heavy Duty Center 1.000 x 3
1122471 2 DB|> 5 2.88 6.00 6.00 186.70 84.6951.750 x 13.000 x 31.500Extra Heavy Duty End 1.000 x 3
8E4193 1 EBC 7 3.61 4.00 4.00 110.80 50.2631.313 x 15.370 x 23.495Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4194 1 EBC 7 3.61 4.00 4.00 110.60 50.1731.313 x 15.370 x 23.495Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4537 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4538 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 49©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E4193HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4194HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4537HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
8E4538HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
6Y4277 1 DB/| 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
6Y4278 1 DB|\ 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
1003139 1 DB/| 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
1003140 1 DB|\ 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
1368757 1 DB/| 7 3.61 4.00 4.00 175.28 79.5132.375 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
1368756 1 DB|\ 7 3.61 4.00 4.00 175.28 79.5132.375 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
7T5936-10 1 SE|| 19 4.75 6.00 6.00 407.90 185.021.250 x 10.000 x 117.000Dozer Blade Support 1.063
6I8403-10 2 SE// 7 6.42 3.25 3.25 63.50 28.801.250 x 10.000 x 21.500Dozer End Bit Support 1.0636.58 4.00 4.00 ...2nd Row1.063
D8 N R T Semi-UKMB LAASerial Number:
4Z9058 1 DB|| 13 2.40 6.00 6.00 296.00 134.26131.125 x 13.000 x 76.800Center 1.000 x 3
6Y5540 2 DB|> 5 2.88 6.00 6.00 117.70 53.3951.125 x 13.000 x 31.500End 1.000 x 3
4Z9058-11 1 DB|| 13 2.40 6.00 6.00 363.00 164.65131.375 x 13.000 x 76.800Heavy Duty Center 1.000 x 3
7T9125 2 DB|> 5 2.88 6.00 6.00 145.70 66.0951.375 x 13.000 x 31.500Heavy Duty End 1.000 x 3
8E4193 1 EBC 7 3.61 4.00 4.00 110.80 50.2631.313 x 15.370 x 23.495Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4194 1 EBC 7 3.61 4.00 4.00 110.60 50.1731.313 x 15.370 x 23.495Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4537 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4538 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4193HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4194HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4537HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
8E4538HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
6Y4277 1 DB/| 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
6Y4278 1 DB|\ 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
1003139 1 DB/| 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 50©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1003140 1 DB|\ 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
1368757 1 DB/| 7 3.61 4.00 4.00 175.28 79.5132.375 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
1368756 1 DB|\ 7 3.61 4.00 4.00 175.28 79.5132.375 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
D8 N R T Full-U1JH 2WP 6AH 9CH 9WP CXBSerial Number:
9W5232 2 DB|> 5 3.69 6.00 6.00 121.90 55.2951.125 x 13.000 x 32.438Center 1.000 x 3
4T6378 2 DB|| 6 2.75 6.00 6.00 136.50 61.9261.125 x 13.000 x 35.500End 1.000 x 3
7T9127 2 DB|> 5 3.69 6.00 6.00 150.20 68.1351.375 x 13.000 x 32.438Heavier Center 1.000 x 3
9W6092 2 DB|| 6 2.75 6.00 6.00 168.50 76.431.375 x 13.000 x 35.500Heavier End 1.000 x 3
1122473 2 DB|> 5 3.69 6.00 6.00 190.00 86.1851.750 x 13.000 x 32.438Extra Heavy Duty Center 1.000 x 3
1122475 2 DB|| 6 2.75 6.00 6.00 213.00 96.6261.750 x 13.000 x 35.500Extra Heavy Duty End 1.000 x 3
8E4193 1 EBC 7 3.61 4.00 4.00 110.80 50.2631.313 x 15.370 x 23.495Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4194 1 EBC 7 3.61 4.00 4.00 110.60 50.1731.313 x 15.370 x 23.495Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4537 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4538 1 EBC 7 3.61 4.00 4.00 120.30 54.5731.376 x 15.371 x 23.496Cast End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
8E4193HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4194HC 1 EBHC 7 3.69 4.00 4.00 126.90 57.5631.625 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
8E4537HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit RH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
8E4538HC 1 EBHC 7 3.63 4.00 4.00 155.20 70.4032.000 x 15.875 x 23.500Hot Cup End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
6Y4277 1 DB/| 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
6Y4278 1 DB|\ 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit LH 1.000 x 34 2.38 3.25 3.25 ...2nd Row1.000 x 3
1003139 1 DB/| 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit RH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
1003140 1 DB|\ 7 3.69 4.00 4.00 141.10 64.0032.000 x 13.000 x 22.000Level Cut End Bit LH 1.000 x 34 2.44 3.25 3.25 ...2nd Row1.000 x 3
1368757 1 DB/| 7 3.61 4.00 4.00 175.28 79.5132.375 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
1368756 1 DB|\ 7 3.61 4.00 4.00 175.28 79.5132.375 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 34 2.36 3.25 3.25 ...2nd Row1.000 x 3
7T7831-10 1 SE|| 12 2.81 6.00 6.00 249.60 113.221.250 x 10.000 x 71.625Dozer Blade Support 1.063
6I8402-10 2 SE// 12 7.35 6.00 6.00 173.90 78.881.250 x 10.000 x 53.060Dozer Blade/End Bit Support 1.063
D9 Angle52C 90D 11E 26ESerial Number:
4T6388 1 DB|| 7 2.94 6.00 6.00 161.30 73.1671.125 x 13.000 x 41.875Center 1.000 x 3.75
4T6387 2 DB|| 9 2.88 6.00 6.00 207.10 93.9491.125 x 13.000 x 53.750End 1.000 x 3.75
7J2966 1 DB|| 7 2.88 6.00 6.00 235.50 106.8271.625 x 13.000 x 41.750Heavy Duty Center 1.000 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 51©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7J2965 2 DB|| 9 2.88 6.00 6.00 303.30 137.5791.625 x 13.000 x 53.750Heavy Duty End 1.000 x 3.75
8E4197 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
8E4196 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
8E4539 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
8E4540 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
3G8291 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit RH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
3G8292 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit LH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
3G8283 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
3G8284 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 3.25 ...2nd Row1.000 x 3.75
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 3.25 ...2nd Row1.000 x 3.75
8E4539HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 3.25 ...2nd Row1.000 x 3.75
8E4540HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 3.25 ...2nd Row1.000 x 3.75
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
D9 Cushion Dozer70F 45GSerial Number:
4T6450 1 DB|| 15 1.44 6.00 6.00 333.70 151.36151.125 x 13.000 x 86.875Center 1.000 x 3.75
4T6388 2 DB|| 7 2.94 6.00 6.00 161.30 73.1671.125 x 13.000 x 41.875End 1.000 x 3.75
3G8291 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit RH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
3G8292 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit LH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
3G8283 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
3G8284 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
D9 Ripper Dozer39KSerial Number:
4T6386 3 DB|| 7 2.50 6.00 6.00 157.90 71.6271.125 x 13.000 x 41.000Center 1.000 x 3.75
9W4500 3 DB|| 7 2.50 6.00 6.00 195.00 88.4571.375 x 13.000 x 41.000Heavier Center 1.000 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 52©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7J2980 3 DB|| 7 2.50 6.00 6.00 231.10 104.8371.625 x 13.000 x 41.000Heavy Duty Center 1.000 x 3.75
4T6391 1 DB/| 7 6.94 4.00 4.00 68.50 31.0731.125 x 13.000 x 19.950Level Cut End Bit RH 1.000 x 3.754 2.44 3.25 6.50 ...2nd Row1.000 x 3.75
4T6392 1 DB|\ 7 6.94 4.00 4.00 68.50 31.0731.125 x 13.000 x 19.950Level Cut End Bit LH 1.000 x 3.754 2.44 3.25 6.50 ...2nd Row1.000 x 3.75
D9 Semi-U25E 06A 21E1-831Serial Number:
4T6459 1 DB|| 9 2.13 6.00 6.00 188.00 85.2891.125 x 13.000 x 52.250Center 1.000 x 3.5
4T6456 2 DB|| 6 3.69 6.00 6.00 143.80 65.2361.125 x 13.000 x 37.375End 1.000 x 3.5
7J2961 1 DB|| 9 2.13 6.00 6.00 294.60 133.6391.625 x 13.000 x 52.250Heavy Duty Center 1.000 x 3.5
7J2960 2 DB|| 6 3.75 6.00 6.00 211.70 96.0361.625 x 13.000 x 37.500Heavy Duty End 1.000 x 3.5
3G8289 1 EBHC 7 6.88 4.00 4.00 132.20 59.9631.375 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
3G8290 1 EBHC 7 6.88 4.00 4.00 132.20 59.9631.375 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
3G8281 1 EBHC 7 6.88 4.00 4.00 155.30 70.4431.625 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
3G8282 1 EBHC 7 6.88 4.00 4.00 155.30 70.4431.625 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
9W9193 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
9W9194 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
D9 Semi-U53E 89D 21E832-UPSerial Number:
4T6448 2 DB|| 10 2.88 6.00 6.00 229.70 104.19101.125 x 13.000 x 59.750Center 1.000 x 3.5
7J2962 2 DB|| 10 2.88 6.00 6.00 337.10 152.91101.625 x 13.000 x 59.750Heavy Duty Center 1.000 x 3.5
3G8289 1 EBHC 7 6.88 4.00 4.00 132.20 59.9631.375 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
3G8290 1 EBHC 7 6.88 4.00 4.00 132.20 59.9631.375 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
3G8281 1 EBHC 7 6.88 4.00 4.00 155.30 70.4431.625 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
3G8282 1 EBHC 7 6.88 4.00 4.00 155.30 70.4431.625 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
9W9193 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
9W9194 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
D9 Full-U55CSerial Number:
4T6453 1 DB<> 13 2.88 6.00 6.00 291.30 132.13131.125 x 13.000 x 77.750Center 1.000 x 3.5
4T6457 2 DB|| 6 2.88 6.00 6.00 137.40 62.3261.125 x 13.000 x 35.750End 1.000 x 3.5
7J2963 1 DB<> 13 2.88 6.00 6.00 427.40 193.87131.625 x 13.000 x 77.750Heavy Duty Center 1.000 x 3.5
7J2964 2 DB|| 6 2.88 6.00 6.00 201.70 91.4961.625 x 13.000 x 35.750Heavy Duty End 1.000 x 3.5
8E4197 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
8E4196 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 53©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E4539 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
8E4540 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
3G8291 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit RH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
3G8292 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit LH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
3G8283 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
3G8284 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.754 2.50 3.25 3.25 ...2nd Row1.000 x 3.75
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 3.25 ...2nd Row1.000 x 3.75
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 3.25 ...2nd Row1.000 x 3.75
8E4539HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 3.25 ...2nd Row1.000 x 3.75
8E4540HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 3.25 ...2nd Row1.000 x 3.75
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
D9 SXS U Dozer (9 blade setup)20HSerial Number:
4T6377 3 DB|| 4 2.63 6.00 6.00 89.30 40.5141.125 x 13.000 x 23.250Center 1.000 x 3.25
4T6378 4 DB|| 6 2.75 6.00 6.00 136.50 61.9261.125 x 13.000 x 35.500Center 1.000 x 3.25
4T6379 2 DB|> 4 2.63 6.00 6.00 86.70 39.3341.125 x 13.000 x 23.250End 1.000 x 3.25
8E4197 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
8E4196 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
8E4539 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit RH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
8E4540 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit LH 1.000 x 3.754 2.36 3.25 3.25 ...2nd Row1.000 x 3.75
3G8291 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit RH 1.000 x 3.254 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8292 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8283 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8284 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 54©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
D9 G H Semi-U05A 18K 46K 73R 61USerial Number:
4T6386 3 DB|| 7 2.50 6.00 6.00 157.90 71.6271.125 x 13.000 x 41.000Center 1.000 x 3.5
9W4500 3 DB|| 7 2.50 6.00 6.00 195.00 88.4571.375 x 13.000 x 41.000Heavier Center 1.000 x 3.5
7J2980 3 DB|| 7 2.50 6.00 6.00 231.10 104.8371.625 x 13.000 x 41.000Heavy Duty Center 1.000 x 3.5
3G8289 1 EBHC 7 6.88 4.00 4.00 132.20 59.9631.375 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
3G8290 1 EBHC 7 6.88 4.00 4.00 132.20 59.9631.375 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
3G8281 1 EBHC 7 6.88 4.00 4.00 155.30 70.4431.625 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
3G8282 1 EBHC 7 6.88 4.00 4.00 155.30 70.4431.625 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
9W9193 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
9W9194 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
7T4342 3 DB|| 7 2.50 6.00 6.00 285.30 129.4171.625 x 16.000 x 41.000Wide Center (Offset Holes) 1.000 x 3.5
7T4093HC 1 EBHC 7 6.88 4.00 4.00 252.50 114.5332.250 x 18.500 x 27.500End Bit (Long Side) RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
7T4092HC 1 EBHC 7 6.88 4.00 4.00 252.50 114.5332.250 x 18.500 x 27.500End Bit (Long Side) LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
9W9193 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500End Bit (Short Side) RH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
9W9194 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500End Bit (Short Side) LH 1.000 x 3.754 2.38 3.25 6.50 ...2nd Row1.000 x 3.75
D9 G H Full-U14C 19K 78XSerial Number:
4T6378 3 DB|| 6 2.75 6.00 6.00 136.50 61.9261.125 x 13.000 x 35.500Center and Outer Ends 1.000 x 3.5
4T6379 2 DB|> 4 2.63 6.00 6.00 86.70 39.3341.125 x 13.000 x 23.250End 1.000 x 3.5
9W6092 3 DB|| 6 2.75 6.00 6.00 168.50 76.4361.375 x 13.000 x 35.500Heavier Center and Outer Ends 1.000 x 3.5
9W9197 2 DB|> 4 2.63 6.00 6.00 107.30 48.6741.375 x 13.000 x 23.250Heavier End 1.000 x 3.5
7J2959 3 DB|| 8 2.75 6.00 6.00 199.90 90.6761.625 x 13.000 x 35.500Heavy Duty Center and Outer Ends 1.000 x 3.5
7J2979 2 DB|> 4 2.63 6.00 6.00 127.20 57.7041.625 x 13.000 x 23.250Heavy Duty End 1.000 x 3.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 55©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E4197 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
3G8291 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8292 1 EBHC 7 3.75 4.00 4.00 112.30 50.9431.375 x 15.500 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8283 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
3G8284 1 EBHC 7 3.75 4.00 4.00 132.00 59.8731.625 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.50 3.25 3.25 ...2nd Row1.000 x 3.5
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
7T4341 3 DB|| 6 2.75 6.00 6.00 247.10 112.0861.625 x 16.000 x 35.500Wide Center (Offset Holes) 1.000 x 3.5
7T4336 1 DB<| 4 2.56 6.00 6.00 152.60 69.2241.625 x 16.000 x 23.125Wide LH End (Offset Holes) 1.000 x 3.5
7T4337 1 DB|> 4 2.56 6.00 6.00 152.60 69.2241.625 x 16.000 x 23.125Wide RH End (Offset Holes) 1.000 x 3.5
7T4095 1 EBHC 7 3.63 4.00 4.00 186.90 84.7832.000 x 18.500 x 24.750End Bit (Long Side) RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
7T4094 1 EBHC 7 3.63 4.00 4.00 186.90 84.7832.000 x 18.500 x 24.750End Bit (Long Side) LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000End Bit (Short Side) RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000End Bit (Short Side) LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
D9 L Cushion Dozer20YSerial Number:
4T6450 1 DB|| 15 1.44 6.00 6.00 333.70 151.36151.125 x 13.000 x 86.875Center 1.000 x 3.75
4T6388 2 DB|| 7 2.94 6.00 6.00 161.30 73.1671.125 x 13.000 x 41.875End 1.000 x 3.75
4T6389 2 EBLC 5 4.81 3.00 3.75 88.30 40.0551.125 x 13.000 x 23.125Level Cut End Bit LH/RH 1.000 x 3.75
D9 L Semi-U18Y1-1875 52Y 42SSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 56©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6386 1 DB|| 7 2.50 6.00 6.00 157.90 71.6271.125 x 13.000 x 41.000Center 1.000 x 3.5
4T6385 2 DB|> 8 3.25 6.00 6.00 181.70 82.4281.125 x 13.000 x 48.125End 1.000 x 3.5
9W4500 1 DB|| 7 2.50 6.00 6.00 195.00 88.4571.375 x 13.000 x 41.000Heavier Center 1.000 x 3.5
9W4502 2 DB|> 8 2.88 6.00 6.00 223.90 101.5681.375 x 13.000 x 48.125Heavier End 1.000 x 3.5
7J2980 1 DB|| 7 2.50 6.00 6.00 231.10 104.8371.625 x 13.000 x 41.000Heavy Duty Center 1.000 x 3.5
9W4508 2 DB|> 8 2.75 6.00 6.00 265.90 120.6181.625 x 13.000 x 48.125Heavy Duty End 1.000 x 3.5
1U1545 1 EBHC 7 3.13 7.00 3.00 145.80 66.1331.625 x 14.500 x 27.000Hot Cup End Bit RH 1.250 x 4.1254 2.00 3.00 7.00 ...2nd Row1.250 x 4.125
1U1546 1 EBHC 7 3.13 7.00 3.00 145.80 66.1331.625 x 14.500 x 27.000Hot Cup End Bit LH 1.250 x 4.1254 2.00 3.00 7.00 ...2nd Row1.250 x 4.125
3G7763 1 DB/| 7 3.11 7.09 2.95 111.00 50.3531.375 x 12.750 x 24.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
3G7764 1 DB|\ 7 3.11 7.09 2.95 111.00 50.3531.375 x 12.750 x 24.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
6Y0310 1 DB|| 7 2.50 6.00 6.00 238.90 108.3671.375 x 16.000 x 41.000Wide Center (Offset Holes) 1.000 x 3.5
6Y0311 1 DB|> 8 3.38 6.00 6.00 274.00 124.2881.375 x 16.000 x 48.125Wide LH End (Offset Holes) 1.000 x 3.5
6Y0312 1 DB<| 8 3.38 6.00 6.00 274.00 124.2881.375 x 16.000 x 48.125Wide RH End (Offset Holes) 1.000 x 3.5
7T4342 1 DB|| 7 2.50 6.00 6.00 285.30 129.4171.625 x 16.000 x 41.000Heavy Duty Wide Center (Offset Holes) 1.000 x 3.5
7T6788 1 DB|> 8 3.38 6.00 6.00 327.50 148.5581.625 x 16.000 x 48.125Heavy Duty Wide RH End (Offset Holes) 1.000 x 3.5
7T6787 1 DB<| 8 3.38 6.00 6.00 327.50 148.5581.625 x 16.000 x 48.125Heavy Duty Wide LH End (Offset Holes) 1.000 x 3.5
6Y0476 1 DB|| 7 2.50 6.00 6.00 310.30 140.7571.750 x 16.000 x 41.000Extra Heavy Duty Wide Center (Offset H 1.000 x 3.5
6Y0477 1 DB<| 8 3.38 6.00 6.00 356.10 161.5281.750 x 16.000 x 48.125Extra Heavy Duty Wide LH End (Offset H 1.000 x 3.5
6Y0478 1 DB|> 8 3.38 6.00 6.00 356.10 161.5281.750 x 16.000 x 48.125Extra Heavy Duty Wide RH End (Offset 1.000 x 3.5
8E4199 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541 1 EBC 7 3.11 7.09 2.95 275.57 125.0034.809 x 18.421 x 28.418Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542 1 EBC 7 3.11 7.09 2.95 280.80 127.3734.809 x 18.421 x 28.418Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755941 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755942 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4199HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.594End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.500End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003131 1 DB/| 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Flat End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 57©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1003132 1 DB|\ 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Flat End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003133 1 DB/| 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Flat End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003134 1 DB|\ 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Flat End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1368755 1 DB/| 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Flat End Bit (Long Side) RH 1.250 x 4.1254 2.01 5.95 7.09 ...2nd Row1.250 x 4.125
1368754 1 DB|\ 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Flat End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
D9 L Semi-U18Y1876-UPSerial Number:
7T9782 2 DB|| 6 2.88 6.00 6.00 206.10 93.4961.375 x 16.000 x 35.750Center 1.250 x 4.125
7T9779 2 DB|> 5 3.75 6.00 6.00 183.50 83.2351.375 x 16.000 x 32.750End 1.250 x 4.125
9W3928 2 DB|| 6 2.88 6.00 6.00 267.20 121.2061.750 x 16.000 x 35.750Extra Heavy Duty Center 1.250 x 4.125
9W3930 2 DB|> 5 3.75 6.00 6.00 239.00 108.4151.750 x 16.000 x 32.750Extra Heavy Duty End 1.250 x 4.125
8E4199 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541 1 EBC 7 3.11 7.09 2.95 275.57 125.0034.809 x 18.421 x 28.418Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542 1 EBC 7 3.11 7.09 2.95 280.80 127.3734.809 x 18.421 x 28.418Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755941 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755942 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4199HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.594Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003131 1 DB/| 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003132 1 DB|\ 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003133 1 DB/| 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003134 1 DB|\ 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1368755 1 DB/| 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 5.95 7.09 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 58©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1368754 1 DB|\ 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
D9 L Full-U19Y1-1474 78SSerial Number:
4T6381 2 DB|| 9 2.63 6.00 6.00 204.60 92.8191.125 x 13.000 x 53.250Center 1.000 x 3.5
4T6382 2 DB|> 6 2.00 3.00 6.00 92.10 41.7861.125 x 13.000 x 25.000End 1.000 x 3.5
7T9126 2 DB|| 9 2.63 6.00 6.00 253.30 114.8991.375 x 13.000 x 53.250Heavier Center 1.000 x 3.5
9W4503 2 DB|> 6 2.00 3.00 6.00 112.00 50.8061.375 x 13.000 x 25.000Heavier End 1.000 x 3.5
9W4507 2 DB|| 9 2.63 6.00 6.00 287.00 130.1891.625 x 13.000 x 53.250Heavy Duty Center 1.000 x 3.5
9W4506 2 DB|> 6 2.00 3.00 6.00 128.00 58.0661.625 x 13.000 x 25.000Heavy Duty End 1.000 x 3.5
1U1545 1 EBHC 7 3.13 7.00 3.00 145.80 66.1331.625 x 14.500 x 27.000Hot Cup End Bit RH 1.250 x 4.1254 2.00 3.00 7.00 ...2nd Row1.250 x 4.125
1U1546 1 EBHC 7 3.13 7.00 3.00 145.80 66.1331.625 x 14.500 x 27.000Hot Cup End Bit LH 1.250 x 4.1254 2.00 3.00 7.00 ...2nd Row1.250 x 4.125
3G7763 1 DB/| 7 3.11 7.09 2.95 111.00 50.3531.375 x 12.750 x 24.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
3G7764 1 DB|\ 7 3.11 7.09 2.95 111.00 50.3531.375 x 12.750 x 24.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
6Y0313 2 DB|| 9 2.63 6.00 6.00 310.40 140.8091.375 x 16.000 x 53.250Wide Center (Offset Holes) 1.000 x 3.5
6Y0314 1 DB|> 6 2.00 3.00 6.00 139.70 63.3761.375 x 16.000 x 25.000Wide RH End (Offset Holes) 1.000 x 3.5
6Y0315 1 DB<| 6 2.00 3.00 6.00 139.70 63.3761.375 x 16.000 x 25.000Wide LH End (Offset Holes) 1.000 x 3.5
7T4335 2 DB|| 9 2.63 6.00 6.00 370.60 168.1091.625 x 16.000 x 53.250Heavy Duty Wide Center (Offset Holes) 1.000 x 3.5
7T4343 1 DB|> 6 2.00 3.00 6.00 166.00 75.3061.625 x 16.000 x 25.000Heavy Duty Wide RH End (Offset Holes) 1.000 x 3.5
7T4344 1 DB<| 6 2.00 3.00 6.00 166.00 75.3061.625 x 16.000 x 25.000Heavy Duty Wide LH End (Offset Holes) 1.000 x 3.5
6Y0479 2 DB|| 9 2.63 6.00 6.00 403.10 182.8491.750 x 16.000 x 53.250Extra Heavy Duty Wide Center (Offset H 1.000 x 3.5
6Y0480 1 DB|> 6 2.00 3.00 6.00 177.70 80.6061.750 x 16.000 x 25.000Extra Heavy Duty Wide RH End (Offset 1.000 x 3.5
6Y0481 1 DB<| 6 2.00 3.00 6.00 177.70 80.6061.750 x 16.000 x 25.000Extra Heavy Duty Wide LH End (Offset H 1.000 x 3.5
8E4199 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541 1 EBC 7 3.11 7.09 2.95 275.57 125.0034.809 x 18.421 x 28.418Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542 1 EBC 7 3.11 7.09 2.95 280.80 127.3734.809 x 18.421 x 28.418Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755941 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755942 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4199HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.594End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 59©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7T4688 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.500End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003131 1 DB/| 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Flat End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003132 1 DB|\ 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Flat End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003133 1 DB/| 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Flat End Bit (Long Side) RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003134 1 DB|\ 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Flat End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1368755 1 DB/| 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Flat End Bit (Long Side) RH 1.250 x 4.1254 2.01 5.95 7.09 ...2nd Row1.250 x 4.125
1368754 1 DB|\ 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Flat End Bit (Long Side) LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
D9 L Full-U19Y1475-UPSerial Number:
9W0775 3 DB|| 5 2.94 6.00 6.00 169.00 76.6651.375 x 16.000 x 29.875Center 1.250 x 4.125
7T9781 2 DB|> 5 5.00 6.00 6.00 193.90 87.9551.375 x 16.000 x 34.500End 1.250 x 4.125
9W3931 3 DB|| 5 2.94 6.00 6.00 224.00 101.6051.750 x 16.000 x 29.875Extra Heavy Duty Center 1.250 x 4.125
9W3929 2 DB|> 5 5.50 6.00 6.00 274.00 124.2851.750 x 16.000 x 34.500Extra Heavy Duty End 1.250 x 4.125
8E4199 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541 1 EBC 7 3.11 7.09 2.95 275.57 125.0034.809 x 18.421 x 28.418Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542 1 EBC 7 3.11 7.09 2.95 280.80 127.3734.809 x 18.421 x 28.418Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755941 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755942 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4199HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.594Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003131 1 DB/| 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003132 1 DB|\ 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003133 1 DB/| 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 60©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1003134 1 DB|\ 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1368755 1 DB/| 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 5.95 7.09 ...2nd Row1.250 x 4.125
1368754 1 DB|\ 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
D9 N R T Semi-U1MH 5BH 1LP 2LP 7NH 2ZP 2BP 9LH 9RP CLC CLN CLY CMASerial Number:
6Y5539 1 DB|| 12 2.19 6.00 6.00 271.00 122.92121.125 x 13.000 x 70.375Center 1.000 x 3.5
6Y5540 2 DB|> 5 2.88 6.00 6.00 117.70 53.3951.125 x 13.000 x 31.500End 1.000 x 3.5
7T5702 1 DB|| 12 2.19 6.00 6.00 334.00 151.50121.375 x 13.000 x 70.375Heavier Center 1.000 x 3.5
7T9125 2 DB|> 5 2.88 6.00 6.00 145.70 66.0951.375 x 13.000 x 31.500Heavier End 1.000 x 3.5
9W7043 1 DB|| 12 2.19 6.00 6.00 429.20 194.68121.750 x 13.000 x 70.375Extra Heavy Duty Center 1.000 x 3.5
1122471 2 DB|> 5 2.88 6.00 6.00 186.70 84.6951.750 x 13.000 x 31.500Extra Heavy Duty End 1.000 x 3.5
8E4197 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
6Y4277 1 DB/| 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit RH 1.000 x 3.54 2.44 3.25 3.25 ...2nd Row1.000 x 3.5
6Y4278 1 DB|\ 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1096347-12 1 SE|| 22 4.75 6.00 6.00 554.00 251.291.500 x 10.000 x 134.500Dozer Blade Support 1.063
8E5590-12 2 SE\\ 7 6.58 4.00 4.00 85.00 38.561.500 x 10.000 x 22.000Dozer End Bit Support 1.0635.33 3.25 3.25 ...2nd Row1.063
D9 N R T Full-U1LH 2ZH 1MP CMH CMN CMS CMW CMZSerial Number:
6Y5538 1 DB|| 15 2.50 6.00 6.00 342.10 155.17151.125 x 13.000 x 89.000Center 1.000 x 3.5
6Y5540 2 DB|> 5 2.88 6.00 6.00 117.70 53.3951.125 x 13.000 x 31.500End 1.000 x 3.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 61©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7T5701 1 DB|| 15 2.50 6.00 6.00 422.50 191.64151.375 x 13.000 x 89.000Heavier Center 1.000 x 3.5
7T9125 2 DB|> 5 2.88 6.00 6.00 145.70 66.0951.375 x 13.000 x 31.500Heavier End 1.000 x 3.5
9W7044 1 DB|| 15 2.50 6.00 6.00 542.90 246.26151.750 x 13.000 x 89.000Extra Heavy Duty Center 1.000 x 3.5
1122471 2 DB|> 5 2.88 6.00 6.00 186.70 84.6951.750 x 13.000 x 31.500Extra Heavy Duty End 1.000 x 3.5
8E4197 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
6Y4277 1 DB/| 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit RH 1.000 x 3.54 2.44 3.25 3.25 ...2nd Row1.000 x 3.5
6Y4278 1 DB|\ 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E9227-12 1 SE|| 15 2.63 6.00 6.00 373.20 169.281.500 x 10.000 x 89.250Dozer Blade Support 1.063
8E9228-12 2 SE// 12 7.35 6.00 6.00 210.30 95.391.500 x 10.000 x 53.436Dozer Blade/End Bit Support 1.063
D10 Coal Dozer83WSerial Number:
9J3751 2 DB|| 10 2.94 3.00 3.00 223.00 101.15101.375 x 13.000 x 47.875Center 1.000 x 3.75
4T6538 2 EBLC 6 5.06 3.00 3.00 134.00 60.7861.375 x 13.000 x 28.125Level Cut End Bit LH/RH 1.000 x 3.75
D10 Semi-U79WSerial Number:
1U4459 2 DB|| 9 2.25 3.00 3.00 234.00 106.1491.375 x 16.000 x 40.500Center 1.250 x 4.125
1U4455 2 DB|> 9 2.25 3.00 3.00 223.90 101.5691.375 x 16.000 x 40.375End 1.250 x 4.125
4T0081 2 DB|| 9 2.25 3.00 3.00 274.20 124.3891.625 x 16.000 x 40.500Heavier Center 1.250 x 4.125
4T0082 2 DB|> 9 2.25 3.00 3.00 265.70 120.5291.625 x 16.000 x 40.375Heavier End 1.250 x 4.125
6Y0016 2 DB|| 9 2.25 3.00 3.00 299.30 135.7691.750 x 16.000 x 40.500Heavy Duty Center 1.250 x 4.125
6Y0017 2 DB|> 9 2.25 3.00 3.00 289.90 131.5091.750 x 16.000 x 40.375Heavy Duty End 1.250 x 4.125
4T0607 2 DB|| 9 2.25 3.00 3.00 367.00 166.4792.000 x 16.000 x 40.500Extra Heavy Duty Center 1.250 x 4.125
4T0604 2 DB|> 9 2.25 3.00 3.00 367.00 166.4792.000 x 16.000 x 40.375Extra Heavy Duty End 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 62©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6Y0021 2 DB|| 9 2.25 3.00 3.00 400.80 181.8092.375 x 16.000 x 40.500Super Heavy Duty Center 1.250 x 4.125
6Y0020 2 DB|> 9 2.25 3.00 3.00 390.00 176.9092.375 x 16.000 x 40.375Super Heavy Duty End 1.250 x 4.125
8E4543 1 EBC 9 2.01 2.95 9.29 363.90 165.0645.413 x 19.989 x 31.980Cast End Bit RH 1.250 x 55 2.95 2.95 7.64 ...2nd Row1.250 x 5
8E4544 1 EBC 9 2.01 2.95 9.29 363.90 165.0645.413 x 19.989 x 31.980Cast End Bit LH 1.250 x 55 2.95 2.95 7.64 ...2nd Row1.250 x 5
8E4545 1 EBC 9 2.01 2.95 9.29 387.50 175.7745.568 x 19.990 x 31.982Cast End Bit RH 1.250 x 55 2.95 2.95 7.64 ...2nd Row1.250 x 5
8E4546 1 EBC 9 2.01 2.95 9.29 387.50 175.7745.568 x 19.990 x 31.982Cast End Bit LH 1.250 x 55 2.95 2.95 7.64 ...2nd Row1.250 x 5
2755445 1 EBC 9 2.00 2.95 9.29 474.43 215.2045.591 x 20.669 x 32.087Extra Extended Wear Cast End Bit RH 1.250 x 55 2.97 2.95 7.09 ...2nd Row1.250 x 5
2755446 1 EBC 9 2.00 2.95 9.29 474.43 215.2045.591 x 20.669 x 32.087Extra Extended Wear Cast End Bit LH 1.250 x 55 2.97 2.95 7.09 ...2nd Row1.250 x 5
8E4543HC 1 EBHC 9 2.01 2.95 9.29 332.30 150.7342.500 x 20.000 x 32.000Hot Cup End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E4544HC 1 EBHC 9 2.08 2.95 9.29 332.30 150.7342.500 x 20.000 x 32.000Hot Cup End Bit LH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E4545HC 1 EBHC 9 2.01 2.95 9.29 396.00 179.6243.000 x 20.000 x 32.000Hot Cup End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E4546HC 1 EBHC 9 2.01 2.95 9.29 396.00 179.6243.000 x 20.000 x 32.000Hot Cup End Bit LH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E9785 1 EBFC 9 2.01 2.95 9.29 291.60 132.2742.500 x 15.500 x 30.500Flat Shape Cut End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E9786 1 EBFC 9 2.06 3.00 9.25 291.60 132.2742.500 x 15.500 x 30.500Flat Shape Cut End Bit LH 1.250 x 55 3.00 3.00 7.63 ...2nd Row1.250 x 5
8E9748 1 EBFC 9 2.06 3.00 9.25 391.00 177.3543.000 x 15.500 x 30.500Flat Shape Cut End Bit LH 1.250 x 55 3.00 3.00 7.63 ...2nd Row1.250 x 5
8E9749 1 EBFC 9 2.06 3.00 9.25 391.00 177.3543.000 x 15.500 x 30.500Flat Shape Cut End Bit RH 1.250 x 55 3.00 3.00 7.63 ...2nd Row1.250 x 5
D10 Full-U80WSerial Number:
1U4458 3 DB|| 9 2.94 3.00 3.00 241.00 109.3291.375 x 16.000 x 41.875Center 1.250 x 4.125
1U4457 2 DB|> 7 3.25 3.00 3.00 171.00 77.5671.375 x 16.000 x 30.875End 1.250 x 4.125
4T0083 3 DB|| 9 2.94 3.00 3.00 285.20 129.3691.625 x 16.000 x 41.875Heavier Center 1.250 x 4.125
4T0084 2 DB|> 7 3.25 3.00 3.00 201.00 91.1771.625 x 16.000 x 30.875Heavier End 1.250 x 4.125
6Y0018 3 DB|| 9 2.94 3.00 3.00 309.90 140.5791.750 x 16.000 x 41.875Heavy Duty Center 1.250 x 4.125
6Y0019 2 DB|> 7 3.25 3.00 3.00 219.00 99.3471.750 x 16.000 x 30.875Heavy Duty End 1.250 x 4.125
4T0609 3 DB|| 9 2.94 3.00 3.00 352.90 160.0792.000 x 16.000 x 41.875Extra Heavy Duty Center 1.250 x 4.125
4T0608 2 DB|> 7 3.25 3.00 3.00 249.20 113.0472.000 x 16.000 x 30.875Extra Heavy Duty End 1.250 x 4.125
6Y0023 3 DB|| 9 2.94 3.00 3.00 415.10 188.2992.375 x 16.000 x 41.875Super Heavy Duty Center 1.250 x 4.125
6Y0022 2 DB|> 7 3.25 3.00 3.00 293.20 132.9972.375 x 16.000 x 30.875Super Heavy Duty End 1.250 x 4.125
8E4543 1 EBC 9 2.01 2.95 9.29 363.90 165.0645.413 x 19.989 x 31.980Cast End Bit RH 1.250 x 55 2.95 2.95 7.64 ...2nd Row1.250 x 5
8E4544 1 EBC 9 2.01 2.95 9.29 363.90 165.0645.413 x 19.989 x 31.980Cast End Bit LH 1.250 x 55 2.95 2.95 7.64 ...2nd Row1.250 x 5
8E4545 1 EBC 9 2.01 2.95 9.29 387.50 175.7745.568 x 19.990 x 31.982Cast End Bit RH 1.250 x 55 2.95 2.95 7.64 ...2nd Row1.250 x 5
8E4546 1 EBC 9 2.01 2.95 9.29 387.50 175.7745.568 x 19.990 x 31.982Cast End Bit LH 1.250 x 55 2.95 2.95 7.64 ...2nd Row1.250 x 5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 63©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2755445 1 EBC 9 2.00 2.95 9.29 474.43 215.2045.591 x 20.669 x 32.087Extra Extended Wear Cast End Bit RH 1.250 x 55 2.97 2.95 7.09 ...2nd Row1.250 x 5
2755446 1 EBC 9 2.00 2.95 9.29 474.43 215.2045.591 x 20.669 x 32.087Extra Extended Wear Cast End Bit LH 1.250 x 55 2.97 2.95 7.09 ...2nd Row1.250 x 5
8E4543HC 1 EBHC 9 2.01 2.95 9.29 332.30 150.7342.500 x 20.000 x 32.000Hot Cup End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E4544HC 1 EBHC 9 2.08 2.95 9.29 332.30 150.7342.500 x 20.000 x 32.000Hot Cup End Bit LH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E4545HC 1 EBHC 9 2.01 2.95 9.29 396.00 179.6243.000 x 20.000 x 32.000Hot Cup End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E4546HC 1 EBHC 9 2.01 2.95 9.29 396.00 179.6243.000 x 20.000 x 32.000Hot Cup End Bit LH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E9785 1 EBFC 9 2.01 2.95 9.29 291.60 132.2742.500 x 15.500 x 30.500Flat Shape Cut End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
8E9786 1 EBFC 9 2.06 3.00 9.25 291.60 132.2742.500 x 15.500 x 30.500Flat Shape Cut End Bit LH 1.250 x 55 3.00 3.00 7.63 ...2nd Row1.250 x 5
8E9748 1 EBFC 9 2.06 3.00 9.25 391.00 177.3543.000 x 15.500 x 30.500Flat Shape Cut End Bit LH 1.250 x 55 3.00 3.00 7.63 ...2nd Row1.250 x 5
8E9749 1 EBFC 9 2.06 3.00 9.25 391.00 177.3543.000 x 15.500 x 30.500Flat Shape Cut End Bit RH 1.250 x 55 3.00 3.00 7.63 ...2nd Row1.250 x 5
D10 N R T Semi-U1RH 7RH 4KP 6EP BHJ BHASerial Number:
9W6609 2 DB|| 6 4.56 6.00 6.00 225.80 102.4261.375 x 16.000 x 39.125Center 1.250 x 4.125
9W6608 2 DB|> 5 4.38 6.00 6.00 189.00 85.7351.375 x 16.000 x 33.812End 1.250 x 4.125
9W6656 2 DB|| 6 4.56 6.00 6.00 290.30 131.6861.750 x 16.000 x 39.125Heavier Center 1.250 x 4.125
9W6657 2 DB|> 5 4.38 6.00 6.00 242.80 110.1351.750 x 16.000 x 33.813Heavier End 1.250 x 4.125
8E2085 2 DB|| 6 4.56 6.00 6.00 393.40 178.4462.375 x 16.000 x 39.125Heavy Duty Center 1.250 x 4.125
8E2086 2 DB|> 5 5.44 6.00 6.00 331.10 150.1852.375 x 16.000 x 33.813Heavy Duty End 1.250 x 4.125
1359580 2 DB|| 6 4.56 6.00 6.00 489.00 221.8163.000 x 16.000 x 39.125Extra Heavy Duty Center 1.250 x 4.125
1359579 2 DB|> 5 4.38 6.00 6.00 409.00 185.5253.000 x 16.000 x 33.813Extra Heavy Duty End 1.250 x 4.125
8E4199 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541 1 EBC 7 3.11 7.09 2.95 275.57 125.0034.809 x 18.421 x 28.418Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542 1 EBC 7 3.11 7.09 2.95 280.80 127.3734.809 x 18.421 x 28.418Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755941 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755942 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4199HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 64©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7T4689 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.594Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003131 1 DB/| 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003132 1 DB|\ 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003133 1 DB/| 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003134 1 DB|\ 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1368755 1 DB/| 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 5.95 7.09 ...2nd Row1.250 x 4.125
1368754 1 DB|\ 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1959171 2 DB|| 6 4.56 6.00 6.00 395.00 179.1762.375 x 16.000 x 39.125Carbide Impreg Center 1.250 x 4.125
1959170 1 DB|> 5 4.38 6.00 6.00 330.00 149.6952.375 x 16.000 x 33.813Carbide Impreg End RH 1.250 x 4.125
2011230 1 DB<| 5 4.38 6.00 6.00 330.00 149.6952.375 x 16.000 x 33.813Carbide Impreg End LH 1.250 x 4.125
1957173 1 EBHC 7 3.11 7.09 2.95 269.00 122.0232.250 x 19.000 x 29.000Carbide Impreg Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1957174 1 EBHC 7 3.11 7.09 2.95 269.00 122.0232.250 x 19.000 x 29.000Carbide Impreg Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1359793 2Weld on HA Edge Segment
8E7430-12 1 SE|| 22 5.50 6.00 6.00 697.30 316.291.500 x 11.417 x 147.000Dozer Blade Support 1.438
8E3581-12 2 SE\\ 7 6.14 7.09 2.95 106.60 48.351.500 x 11.417 x 26.096Dozer End Bit Support 1.4385.03 2.95 7.09 ...2nd Row1.438
D10 N R T Full-U1SH 7WH 4LP 6FP BHF BHPSerial Number:
9W6615 3 DB|| 5 4.69 6.00 6.00 191.00 86.6451.375 x 16.000 x 33.375Center 1.250 x 4.125
9W6608 2 DB|> 5 4.38 6.00 6.00 189.00 85.7351.375 x 16.000 x 33.812End 1.250 x 4.125
9W6658 3 DB|| 5 4.69 6.00 6.00 247.80 112.4051.750 x 16.000 x 33.375Heavier Center 1.250 x 4.125
9W6657 2 DB|> 5 4.38 6.00 6.00 242.80 110.1351.750 x 16.000 x 33.813Heavier End 1.250 x 4.125
8E2087 3 DB|| 5 4.69 6.00 6.00 338.00 153.3152.375 x 16.000 x 33.375Heavy Duty Center 1.250 x 4.125
8E2086 2 DB|> 5 5.44 6.00 6.00 331.10 150.1852.375 x 16.000 x 33.813Heavy Duty End 1.250 x 4.125
8E2087-24 3 DB|| 5 4.69 6.00 6.00 414.70 188.1053.000 x 16.000 x 33.375Extra Heavy Duty Center 1.250 x 4.125
1359579 2 DB|> 5 4.38 6.00 6.00 409.00 185.5253.000 x 16.000 x 33.813Extra Heavy Duty End 1.250 x 4.125
8E4199 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541 1 EBC 7 3.11 7.09 2.95 275.57 125.0034.809 x 18.421 x 28.418Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 65©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E4542 1 EBC 7 3.11 7.09 2.95 280.80 127.3734.809 x 18.421 x 28.418Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755941 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755942 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4199HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.594Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003131 1 DB/| 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003132 1 DB|\ 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003133 1 DB/| 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003134 1 DB|\ 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1368755 1 DB/| 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 5.95 7.09 ...2nd Row1.250 x 4.125
1368754 1 DB|\ 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2238149 2 DB|| 5 4.69 6.00 6.00 337.00 152.8652.375 x 16.000 x 33.375Carbide Impreg Center 1.250 x 4.125
1959170 1 DB|> 5 4.38 6.00 6.00 330.00 149.6952.375 x 16.000 x 33.813Carbide Impreg End RH 1.250 x 4.125
2011230 1 DB<| 5 4.38 6.00 6.00 330.00 149.6952.375 x 16.000 x 33.813Carbide Impreg End LH 1.250 x 4.125
1957173 1 EBHC 7 3.11 7.09 2.95 269.00 122.0232.250 x 19.000 x 29.000Carbide Impreg Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1957174 1 EBHC 7 3.11 7.09 2.95 269.00 122.0232.250 x 19.000 x 29.000Carbide Impreg Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1359793 2Weld on HA Edge Segment
8E6867-12 1 SE|| 15 4.75 6.00 6.00 481.50 218.401.500 x 11.471 x 101.000Dozer Blade Support 1.438
8E5080-12 2 SE\\ 12 8.59 6.00 6.00 269.90 122.421.500 x 11.417 x 60.500Dozer Blade/End Bit Support 1.43840.44 7.09 2.95 ...2nd Row1.438
D11 N R Semi-U4BB 4KB 9NH 1AP 4XP 8PPSerial Number:
9W2426 2 DB|| 9 3.63 3.00 3.00 317.30 143.9291.750 x 16.000 x 43.250Center 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 66©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W2425 2 DB|> 9 2.25 3.00 3.00 285.20 129.3691.750 x 16.000 x 40.125End 1.250 x 4.125
9W4495 2 DB|| 9 3.63 3.00 3.00 431.70 195.8292.375 x 16.000 x 43.250Heavy Duty Center 1.250 x 4.125
9W4494 2 DB|> 9 2.25 3.00 3.00 388.90 176.4092.375 x 16.000 x 40.125Heavy Duty End 1.250 x 4.125
1359578 2 DB|| 9 3.63 3.00 3.00 529.70 240.2793.000 x 16.000 x 43.250Extra Heavy Duty Center 1.250 x 4.125
1359577 2 DB|> 9 2.25 3.00 3.00 477.10 216.4193.000 x 16.000 x 40.125Extra Heavy Duty End 1.250 x 4.125
8E4543 1 EBC 9 2.01 2.95 9.29 363.90 165.0645.413 x 19.989 x 31.980Cast End Bit RH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
8E4544 1 EBC 9 2.01 2.95 9.29 363.90 165.0645.413 x 19.989 x 31.980Cast End Bit LH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
8E4545 1 EBC 9 2.01 2.95 9.29 387.50 175.7745.568 x 19.990 x 31.982Cast End Bit RH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
8E4546 1 EBC 9 2.01 2.95 9.29 387.50 175.7745.568 x 19.990 x 31.982Cast End Bit LH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
2755445 1 EBC 9 2.00 2.95 9.29 474.43 215.2045.591 x 20.669 x 32.087Extra Extended Wear Cast End Bit RH 1.250 x 4.1255 2.97 2.95 7.09 ...2nd Row1.250 x 4.125
2755446 1 EBC 9 2.00 2.95 9.29 474.43 215.2045.591 x 20.669 x 32.087Extra Extended Wear Cast End Bit LH 1.250 x 4.1255 2.97 2.95 7.09 ...2nd Row1.250 x 4.125
8E4543HC 1 EBHC 9 2.01 2.95 9.29 332.30 150.7342.500 x 20.000 x 32.000Hot Cup End Bit RH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
8E4544HC 1 EBHC 9 2.08 2.95 9.29 332.30 150.7342.500 x 20.000 x 32.000Hot Cup End Bit LH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
8E4545HC 1 EBHC 9 2.01 2.95 9.29 396.00 179.6243.000 x 20.000 x 32.000Hot Cup End Bit RH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
8E4546HC 1 EBHC 9 2.01 2.95 9.29 396.00 179.6243.000 x 20.000 x 32.000Hot Cup End Bit LH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
1368778 1 DB/| 9 2.01 2.95 9.2942.375 x 16.000 x 28.000Level Cut End Bit RH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
1368779 1 DB|\ 9 2.01 2.95 9.2942.375 x 16.000 x 28.000Level Cut End Bit LH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
8E9785 1 EBFC 9 2.01 2.95 9.29 291.60 132.2742.500 x 15.500 x 30.500Flat Shape Cut End Bit RH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
8E9786 1 EBFC 9 2.06 3.00 9.25 291.60 132.2742.500 x 15.500 x 30.500Flat Shape Cut End Bit LH 1.250 x 4.1255 3.00 3.00 7.63 ...2nd Row1.250 x 4.125
8E9748 1 EBFC 9 2.06 3.00 9.25 391.00 177.3543.000 x 15.500 x 30.500Flat Shape Cut End Bit LH 1.250 x 4.1255 3.00 3.00 7.63 ...2nd Row1.250 x 4.125
8E9749 1 EBFC 9 2.06 3.00 9.25 391.00 177.3543.000 x 15.500 x 30.500Flat Shape Cut End Bit RH 1.250 x 4.1255 3.00 3.00 7.63 ...2nd Row1.250 x 4.125
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1359793 2Weld on HA Edge Segment
1019533-12 1 SE|| 36 2.06 3.00 3.00 788.00 357.431.500 x 11.417 x 167.500Dozer Blade Support 1.438
1019540-12 2 SE\\ 9 5.00 2.95 9.29 123.00 55.791.500 x 11.417 x 29.327Dozer End Bit Support 1.4385.97 2.95 7.64 ...2nd Row1.438
D11 N R Full-U4CB 5TB 9MH 9ZH 4YP 8RPSerial Number:
9W2426 1 DB|| 9 3.63 3.00 3.00 317.30 143.9291.750 x 16.000 x 43.250Center 1.250 x 4.125
9W2424 2 DB|| 9 2.19 3.00 3.00 295.30 133.9591.750 x 16.000 x 40.375Intermediate 1.250 x 4.125
9W2425 2 DB|> 9 2.25 3.00 3.00 285.20 129.3691.750 x 16.000 x 40.125End 1.250 x 4.125
9W4495 1 DB|| 9 3.63 3.00 3.00 431.70 195.8292.375 x 16.000 x 43.250Heavy Duty Center 1.250 x 4.125
9W4493 2 DB|| 9 2.13 3.00 3.00 400.40 181.6292.375 x 16.000 x 40.250Heavy Duty Intermediate 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 67©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W4494 2 DB|> 9 2.25 3.00 3.00 388.90 176.4092.375 x 16.000 x 40.125Heavy Duty End 1.250 x 4.125
1359578 1 DB|| 9 3.63 3.00 3.00 529.70 240.2793.000 x 16.000 x 43.250Extra Heavy Duty Center 1.250 x 4.125
1957187 2 DB|| 9 2.13 3.00 3.00 491.00 222.7193.000 x 16.000 x 40.250Extra Heavy Duty Intermediate 1.250 x 4.125
1359577 2 DB|> 9 2.25 3.00 3.00 477.10 216.4193.000 x 16.000 x 40.125Extra Heavy Duty End 1.250 x 4.125
8E4543 1 EBC 9 2.01 2.95 9.29 363.90 165.0645.413 x 19.989 x 31.980Cast End Bit RH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
8E4544 1 EBC 9 2.01 2.95 9.29 363.90 165.0645.413 x 19.989 x 31.980Cast End Bit LH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
8E4545 1 EBC 9 2.01 2.95 9.29 387.50 175.7745.568 x 19.990 x 31.982Cast End Bit RH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
8E4546 1 EBC 9 2.01 2.95 9.29 387.50 175.7745.568 x 19.990 x 31.982Cast End Bit LH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
2755445 1 EBC 9 2.00 2.95 9.29 474.43 215.2045.591 x 20.669 x 32.087Extra Extended Wear Cast End Bit RH 1.250 x 4.1255 2.97 2.95 7.09 ...2nd Row1.250 x 4.125
2755446 1 EBC 9 2.00 2.95 9.29 474.43 215.2045.591 x 20.669 x 32.087Extra Extended Wear Cast End Bit LH 1.250 x 4.1255 2.97 2.95 7.09 ...2nd Row1.250 x 4.125
8E4543HC 1 EBHC 9 2.01 2.95 9.29 332.30 150.7342.500 x 20.000 x 32.000Hot Cup End Bit RH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
8E4544HC 1 EBHC 9 2.08 2.95 9.29 332.30 150.7342.500 x 20.000 x 32.000Hot Cup End Bit LH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
8E4545HC 1 EBHC 9 2.01 2.95 9.29 396.00 179.6243.000 x 20.000 x 32.000Hot Cup End Bit RH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
8E4546HC 1 EBHC 9 2.01 2.95 9.29 396.00 179.6243.000 x 20.000 x 32.000Hot Cup End Bit LH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
1368778 1 DB/| 9 2.01 2.95 9.2942.375 x 16.000 x 28.000Level Cut End Bit RH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
1368779 1 DB|\ 9 2.01 2.95 9.2942.375 x 16.000 x 28.000Level Cut End Bit LH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
8E9785 1 EBFC 9 2.01 2.95 9.29 291.60 132.2742.500 x 15.500 x 30.500Flat Shape Cut End Bit RH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
8E9786 1 EBFC 9 2.06 3.00 9.25 291.60 132.2742.500 x 15.500 x 30.500Flat Shape Cut End Bit LH 1.250 x 4.1255 3.00 3.00 7.63 ...2nd Row1.250 x 4.125
8E9748 1 EBFC 9 2.06 3.00 9.25 391.00 177.3543.000 x 15.500 x 30.500Flat Shape Cut End Bit LH 1.250 x 4.1255 3.00 3.00 7.63 ...2nd Row1.250 x 4.125
8E9749 1 EBFC 9 2.06 3.00 9.25 391.00 177.3543.000 x 15.500 x 30.500Flat Shape Cut End Bit RH 1.250 x 4.1255 3.00 3.00 7.63 ...2nd Row1.250 x 4.125
1386484 1 DB|| 9 3.63 3.00 3.0091.750 x 19.000 x 43.250Wide Center (Offset Holes) 1.250 x 4.125
1386483 2 DB|| 9 2.19 3.00 3.00 176.6791.750 x 19.000 x 40.375Wide Center (Offset Holes) 1.250 x 4.125
1386485 1 DB|> 9 2.25 3.00 3.0091.750 x 19.000 x 40.125Wide End (Offset Holes) 1.250 x 4.125
1386486 1 DB<| 9 2.25 3.00 3.0091.750 x 19.000 x 40.125Wide End (Offset Holes) 1.250 x 4.125
1366753 1 EBFC 9 2.01 2.95 9.29 384.70 174.5042.500 x 21.496 x 32.500Flat End Bit (Long Side) RH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
1366754 1 EBFC 9 2.01 2.95 9.29 384.70 174.5042.500 x 21.496 x 32.500Flat End Bit (Long Side) LH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
1099053 1 EBFC 9 2.01 2.95 9.29 292.90 132.8642.500 x 14.750 x 32.500End Bit (Short Side) RH 1.250 x 4.1255 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
1099054 1 EBFC 9 2.01 2.95 9.29 292.90 132.8642.500 x 14.750 x 32.500End Bit (Short Side) LH 1.250 x 4.1253 2.97 2.95 7.64 ...2nd Row1.250 x 4.125
1959175 1 DB|| 9 3.63 3.00 3.00 454.60 206.2092.375 x 16.000 x 43.250Carbide Impreg Center 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 68©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Bulldozers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1959173 2 DB|| 9 1.13 3.00 3.00 421.20 191.0592.375 x 16.000 x 40.375Carbide Impreg Center 1.250 x 4.125
1959174 1 DB|> 9 1.88 3.00 3.00 408.80 185.4392.375 x 16.000 x 40.125Carbide Impreg End RH 1.250 x 4.125
2011231 1 DB<| 9 1.88 3.00 3.00 408.80 185.4392.375 x 16.000 x 40.125Carbide Impreg End LH 1.250 x 4.125
1957171 1 EBHC 9 2.01 2.95 9.29 420.00 190.5143.000 x 20.000 x 32.000Carbide Impreg Hot Cup End Bit RH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
1957172 1 EBHC 9 2.01 2.95 9.29 420.00 190.5143.000 x 20.000 x 32.000Carbide Impreg Hot Cup End Bit LH 1.250 x 4.1255 2.95 2.95 7.64 ...2nd Row1.250 x 4.125
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1359793 2Weld on HA Edge Segment
8E6347-12 1 SE|| 27 2.50 3.00 3.00 587.40 266.441.500 x 11.420 x 125.000Dozer Blade Support 1.438
8E6346-12 2 SE\\ 18 3.95 3.00 3.00 304.10 137.941.500 x 11.417 x 68.671Dozer Blade/End Bit Support 1.438
D11 R Carrydozer5JP BHZSerial Number:
2383171 5 DB|| 16 4.75 3.00 3.00 338.40 153.5081.750 x 19.000 x 39.500Reversible Center with Two Rows of Hol 1.250 x 54.75 3.00 3.00 ...2nd Row1.250 x 0
2383177 5 DB|| 16 4.75 3.00 3.00 483.80 219.4582.500 x 19.000 x 39.500HD Reversible Center with Two Rows of 1.250 x 54.75 3.00 3.00 ...2nd Row1.250 x 0
2688751 5 DB|| 16 4.75 3.00 3.00 489.00 221.8182.500 x 19.000 x 39.500Carbide HD Rev. Center with Two Rows 1.250 x 54.75 3.00 3.00 ...2nd Row1.250 x 0
2297052 5 DB|| 8 4.75 3.00 3.00 350.70 159.0781.750 x 19.000 x 39.500Non-Reversible Center with offset Holes 1.250 x 5
2678654 5 DB|| 8 4.75 3.00 3.00 408.30 185.2082.375 x 16.000 x 39.504HD Non-Reversible Center with offset Ho 1.250 x 5
2688750 5 DB|| 8 4.75 3.00 3.00 415.00 188.2482.375 x 16.000 x 39.504Carbide HD Non-Rev. Center with offset 1.250 x 5
2737223 1 EBFC 9 2.01 2.95 9.29 484.90 219.9542.500 x 25.433 x 36.437Penetration End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
2737224 1 EBFC 9 2.01 2.95 9.29 484.90 219.9542.500 x 25.433 x 36.437Penetration End Bit LH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
2737225 EBFC 9 2.01 2.95 9.29 384.70 174.5042.500 x 21.496 x 32.500Flat Shape Cut End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
2737226 EBFC 9 2.01 2.95 9.29 384.70 174.5042.500 x 21.496 x 32.500Flat Shape Cut End Bit LH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
2737230 EBFC 9 2.01 2.95 9.29 463.70 210.3343.000 x 21.496 x 32.500HD Flat Shape Cut End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
2737231 EBFC 9 2.01 2.95 9.29 463.70 210.3343.000 x 21.496 x 32.500HD Flat Shape Cut End Bit LH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
2737234 EBFC 9 2.01 2.95 9.29 482.50 218.8643.000 x 21.496 x 32.500Carbide HD Flat Shape Cut End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
2737235 EBFC 9 2.01 2.95 9.29 482.50 218.8643.000 x 21.496 x 32.500Carbide HD Flat Shape Cut End Bit LH 1.250 x 55 2.97 2.95 7.66 ...2nd Row1.250 x 5
2238127 EBFC 9 2.01 2.95 9.29 596.90 270.7543.000 x 25.433 x 36.437Carbide HD Penetration End Bit RH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
2238128 EBFC 9 2.01 2.95 9.29 596.90 270.7543.000 x 25.433 x 36.437Carbide HD Penetration End Bit LH 1.250 x 55 2.97 2.95 7.64 ...2nd Row1.250 x 5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 69©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
814 56D 23KSerial Number:
4T2921 1 DB|| 7 2.69 6.00 6.00 80.90 36.7070.750 x 10.000 x 41.875Center 0.875 x 2.75
4T2922 2 DB|| 5 2.69 6.00 6.00 57.70 26.1750.750 x 10.000 x 29.875End 0.875 x 2.75
4T2993 1 DB|| 7 2.94 6.00 6.00 107.80 48.9071.000 x 10.000 x 41.875Heavy Duty Center 0.875 x 2.75
4T2992 2 DB|| 5 2.94 6.00 6.00 76.90 34.8851.000 x 10.000 x 29.875Heavy Duty End 0.875 x 2.75
4T6241 1 DB/| 7 2.88 4.00 4.00 40.80 18.5131.000 x 10.000 x 16.250Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6242 1 DB|\ 7 2.88 4.00 4.00 40.80 18.5131.000 x 10.000 x 16.250Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T3019 2 DB|| 5 3.00 12.00 12.00 84.50 38.3350.750 x 8.000 x 54.000Sole Plate 0.750 x 2.5
814 36S 3YPSerial Number:
4T2922 1 DB|| 5 2.69 6.00 6.00 57.70 26.1750.750 x 10.000 x 29.875Center 0.875 x 3
4T2923 2 DB|| 7 2.25 6.00 6.00 78.20 35.4770.750 x 10.000 x 40.500End 0.875 x 3
4T6241 1 DB/| 7 2.88 4.00 4.00 40.80 18.5131.000 x 10.000 x 16.250Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6242 1 DB|\ 7 2.88 4.00 4.00 40.80 18.5131.000 x 10.000 x 16.250Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T3018 2 DB|| 4 3.00 12.00 12.00 65.70 29.8040.750 x 8.000 x 42.000Sole Plate 0.750 x 2.5
815 24K1-1044 59E1-341Serial Number:
4T3008 1 DB|| 11 2.94 4.00 4.00 71.00 32.21110.750 x 8.000 x 45.875Center 0.625 x 2.25
4T3020 2 DB|| 9 0.91 4.00 4.00 52.20 23.6890.750 x 8.000 x 33.813End 0.625 x 2.25
3G8295 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
3G8296 1 EBHC 6 2.00 3.50 3.50 36.40 16.5131.000 x 10.300 x 15.440Hot Cup End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
4T3049 1 DB/| 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit RH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
4T3050 1 DB|\ 6 2.00 3.50 3.50 19.90 9.0330.750 x 8.000 x 14.000Level Cut End Bit LH 0.625 x 2.253 2.00 4.00 4.00 ...2nd Row0.625 x 2.25
815 24K1045-UP 59E342-UPSerial Number:
4T3004 2 DB|| 9 4.38 6.00 6.00 88.10 39.9690.750 x 8.000 x 56.750Center 0.750 x 2.25
4J8261 1 EBC 6 2.00 3.50 3.50 24.80 11.2530.750 x 8.999 x 14.996Cast End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
4J8262 1 EBC 6 2.00 3.50 3.50 24.80 11.2530.750 x 8.999 x 14.996Cast End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
3G8297 1 EBHC 6 2.00 3.50 3.50 35.90 16.2831.000 x 10.300 x 15.440Hot Cup End Bit RH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
3G8298 1 EBHC 6 2.00 3.50 3.50 35.90 16.2831.000 x 10.300 x 15.440Hot Cup End Bit LH 0.750 x 2.253 2.00 4.00 4.00 ...2nd Row0.750 x 2.25
4T3041 1 DB/| 6 1.93 3.50 3.50 20.80 9.4330.750 x 8.000 x 14.890Level Cut End Bit RH 0.750 x 2.253 1.93 4.00 4.00 ...2nd Row0.750 x 2.25
4T3042 1 DB|\ 6 1.93 3.50 3.50 20.80 9.4330.750 x 8.000 x 14.890Level Cut End Bit LH 0.750 x 2.253 1.93 4.00 4.00 ...2nd Row0.750 x 2.25
815 39S 17ZSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T3012 2 DB|| 10 2.44 6.00 6.00 91.30 41.41100.750 x 8.000 x 58.875Center 0.750 x 2.5
5J1419 1 EBC 6 2.25 4.00 4.00 31.70 14.3830.875 x 9.497 x 14.997Cast End Bit RH 0.750 x 2.53 2.25 4.00 4.00 ...2nd Row0.750 x 2.5
5J1420 1 EBC 6 2.25 4.00 4.00 31.70 14.3830.875 x 9.497 x 14.997Cast End Bit LH 0.750 x 2.53 2.25 4.00 4.00 ...2nd Row0.750 x 2.5
3G8319 1 EBHC 6 2.25 4.00 4.00 32.30 14.6530.875 x 9.610 x 16.940Hot Cup End Bit RH 0.750 x 2.53 2.25 4.00 4.00 ...2nd Row0.750 x 2.5
3G8320 1 EBHC 6 2.25 4.00 4.00 32.30 14.6530.875 x 9.610 x 16.970Hot Cup End Bit LH 0.750 x 2.53 2.25 4.00 4.00 ...2nd Row0.750 x 2.5
4T3045 1 DB/| 6 2.25 4.00 4.00 21.50 9.7530.750 x 8.000 x 14.850Level Cut End Bit RH 0.750 x 2.53 2.25 4.00 4.00 ...2nd Row0.750 x 2.5
4T3046 1 DB|\ 6 2.25 4.00 4.00 21.50 9.7530.750 x 8.000 x 14.750Level Cut End Bit LH 0.750 x 2.53 2.25 4.00 4.00 ...2nd Row0.750 x 2.5
816 - F 51KSerial Number:
4T6531 1 DB|| 10 2.94 6.00 6.00 154.10 69.90101.000 x 10.000 x 59.875Center 0.875 x 2.75
4T6532 2 DB|| 6 2.94 6.00 6.00 92.30 41.8761.000 x 10.000 x 35.875End 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
816 - F 41S 15Z 3ZPSerial Number:
4T2922 1 DB|| 5 2.69 6.00 6.00 57.70 26.1750.750 x 10.000 x 29.875Center 0.875 x 3
4T2923 2 DB|| 7 2.25 6.00 6.00 78.20 35.4770.750 x 10.000 x 40.500End 0.875 x 3
4T6241 1 DB/| 7 2.88 4.00 4.00 40.80 18.5131.000 x 10.000 x 16.250Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6242 1 DB|\ 7 2.88 4.00 4.00 40.80 18.5131.000 x 10.000 x 16.250Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
824 S 88HSerial Number:
4T6448 2 DB|| 10 2.88 6.00 6.00 229.70 104.19101.125 x 13.000 x 59.750Center 1.000 x 3.25
3G8289 1 EBHC 7 6.88 4.00 4.00 132.20 59.9631.375 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.254 2.38 3.25 6.50 ...2nd Row1.000 x 0
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8290 1 EBHC 7 6.88 4.00 4.00 132.20 59.9631.375 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.254 2.38 3.25 6.50 ...2nd Row1.000 x 0
3G8281 1 EBHC 7 6.88 4.00 4.00 155.30 70.4431.625 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.254 2.38 3.25 6.50 ...2nd Row1.000 x 0
3G8282 1 EBHC 7 6.88 4.00 4.00 155.30 70.4431.625 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.254 2.38 3.25 6.50 ...2nd Row1.000 x 0
9W9193 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500Hot Cup End Bit RH 1.000 x 3.254 2.38 3.25 6.50 ...2nd Row1.000 x 3.25
9W9194 1 EBHC 7 6.88 4.00 4.00 216.00 97.9832.000 x 16.000 x 27.500Hot Cup End Bit LH 1.000 x 3.254 2.38 3.25 6.50 ...2nd Row1.000 x 3.25
824 C G 35GSerial Number:
4T6514 2 DB|| 10 3.75 6.00 6.00 160.00 72.5731.000 x 10.000 x 61.500Center 0.875 x 4.25
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
7T3491 3 DB|| 7 3.94 6.00 6.00 92.30 41.8771.000 x 8.000 x 43.875Sole Plate (S/N UP TO 35G1222) 0.750 x 2.5
7T3492 3 DB|| 7 3.88 6.00 6.00 91.50 41.5071.000 x 8.000 x 43.750Sole Plate (S/N 35G1223-UP) 0.875 x 2.5
824 C G H 2HPSerial Number:
1229227 2 DB|| 6 2.63 6.00 6.00 91.90 41.6961.000 x 10.000 x 35.250Center 0.875 x 2.75
4T3420 2 DB|| 5 4.06 6.00 6.00 83.90 38.0651.000 x 10.000 x 32.125End 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 3©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T8799 3 DB|| 7 1.63 6.00 6.00 102.20 46.3671.000 x 10.000 x 39.250Sole Plate 0.875 x 2.5
824 BALDERSONSerial Number:
1321041 1 DB|| 52.375 x x Wide Center (Offset Holes)
1324730 1 DB|| 52.375 x x Wide Center (Offset Holes)
1321042 1 DB|> 62.375 x x Wide End (Offset Holes)
1321043 1 DB<| 62.375 x x Wide End (Offset Holes)
1247284 1 72.375 x x End Bit (Long Side) RH
1247285 1 72.375 x x End Bit (Long Side) LH
1282870 1 72.375 x x End Bit (Short Side) RH
1282871 1 72.375 x x End Bit (Short Side) LH
825 C 89XSerial Number:
4T6238 3 DB|| 8 2.63 6.00 6.00 123.00 55.7931.000 x 10.000 x 47.250Center 1.000 x 3
9J1477 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit RH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
9J1478 1 EBC 7 2.88 4.00 4.00 59.40 26.9431.125 x 11.997 x 18.996Cast End Bit LH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
3G8317 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 13.000 x 21.625Hot Cup End Bit RH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
3G8318 1 EBHC 7 2.88 4.00 4.00 77.40 35.1131.250 x 12.986 x 21.553Hot Cup End Bit LH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
3G8287 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit RH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
3G8288 1 EBHC 7 2.88 4.00 4.00 99.40 45.0931.625 x 13.000 x 22.000Hot Cup End Bit LH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
4T6239 1 DB/| 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit RH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
4T6240 1 DB|\ 7 2.88 4.00 4.00 42.20 19.1431.000 x 10.000 x 18.000Level Cut End Bit LH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
4T8089 1 DB/| 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit RH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
4T8090 1 DB|\ 7 2.88 4.00 4.00 50.90 23.0931.125 x 10.000 x 19.125Level Cut End Bit LH 1.000 x 34 2.88 3.00 3.00 ...2nd Row1.000 x 3
825 G 4JPSerial Number:
4T6532 4 DB|| 6 2.94 6.00 6.00 92.30 41.8761.000 x 10.000 x 35.875Center 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 4©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
826 - C G 97X 90K 2GPSerial Number:
4T6515 2 DB|| 12 1.94 6.00 6.00 179.70 81.51121.000 x 10.000 x 69.875Center 0.875 x 3
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
834 825 824 93GSerial Number:
4T6531 1 DB|| 10 2.94 6.00 6.00 154.10 69.90101.000 x 10.000 x 59.875Center 0.875 x 2.75
4T6532 2 DB|| 6 2.94 6.00 6.00 92.30 41.8761.000 x 10.000 x 35.875End 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 5©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
834 824 B C 64GSerial Number:
4T2889 2 DB|| 9 3.75 6.00 6.00 144.80 65.6891.000 x 10.000 x 55.500Center 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6645 2 DB|| 6 3.72 12.00 6.00 144.00 65.3261.000 x 10.000 x 55.440Sole Plate 0.875 x 2.5
834 14BSerial Number:
4T8797 2 DB|> 6 5.50 6.00 6.00 98.70 44.7761.000 x 10.000 x 39.000Center 0.875 x 2.75
4T8798 2 DB|| 7 3.19 6.00 6.00 109.10 49.4971.000 x 10.000 x 42.375End 0.875 x 2.75
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 6©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
3G8293 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8294 1 EBHC 7 2.88 4.00 4.00 55.20 25.0430.875 x 13.125 x 21.625Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 2.754 2.88 3.00 3.00 ...2nd Row0.875 x 2.75
4T8799 2 DB|| 7 1.63 6.00 6.00 102.20 46.3671.000 x 10.000 x 39.250Sole Plate 0.875 x 2.75
--> HEAVY DUTY MINING OPTIONS
1233754 2 DB|| 6 3.19 6.00 6.00 343.90 155.992.500 x 13.000 x 42.375Wide Center (Offset Holes) 0.875
1233755 1 DB|> 6 5.50 6.00 6.00 328.70 149.102.500 x 13.000 x 38.400Wide End (Offset Holes) 0.875
1233756 1 DB<| 6 5.50 6.00 6.00 328.70 149.102.500 x 13.000 x 38.400Wide End (Offset Holes) 0.875
1247284 1 72.375 x x End Bit (Long Side) RH
1247285 1 72.375 x x End Bit (Long Side) LH
1282870 1 72.375 x x End Bit (Short Side) RH
1282871 1 72.375 x x End Bit (Short Side) LH
834 835 27K 36G 96GSerial Number:
4T6515 2 DB|| 12 1.94 6.00 6.00 179.70 81.51121.000 x 10.000 x 69.875Center 0.875 x 3
4T6455 1 DB|| 24 3.50 6.00 6.00241.120 x 12.000 x 138.900Optional One Piece Edge 0.875 x 3
4J8843 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844 1 EBC 7 2.88 4.00 4.00 59.90 27.1731.125 x 11.997 x 18.996Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8843HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4J8844HD 1 EBC 7 2.88 4.00 4.00 80.50 36.5131.126 x 12.430 x 21.231Cast End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8315 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
3G8316 1 EBHC 7 2.95 4.00 4.00 67.50 30.6231.250 x 11.530 x 20.910Hot Cup End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6505 1 DB/| 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit RH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6506 1 DB|\ 7 2.88 4.00 4.00 44.50 20.1831.000 x 10.000 x 18.580Level Cut End Bit LH 0.875 x 34 2.88 3.00 3.00 ...2nd Row0.875 x 3
4T6651 1 DB|| 9 1.94 6.00 6.00 133.50 60.5591.000 x 10.000 x 51.875Sole Plate 0.875 x 2.5
4T6650 2 DB|| 8 1.94 6.00 6.00 114.00 51.7181.000 x 10.000 x 45.875Sole Plate 0.875 x 2.5
--> HEAVY DUTY MINING OPTIONS
1093146 2 DB|| 122.375 x x Wide Center (Offset Holes)
1247284 1 72.375 x x End Bit (Long Side) RH
1247285 1 72.375 x x End Bit (Long Side) LH
1282870 1 72.375 x x End Bit (Short Side) RH
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 7©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1282871 1 72.375 x x End Bit (Short Side) LH
834 G Serial Number:6Y5539 1 DB|| 12 2.19 6.00 6.00 271.00 122.92121.125 x 13.000 x 70.375Center 1.000
4T6386 2 DB|| 7 2.50 6.00 6.00 157.90 71.6271.125 x 13.000 x 41.000End 1.000
1130322 1 DB|| 12 2.19 6.00 6.00 614.50 278.73122.500 x 13.000 x 70.375Heavy Duty Center 1.000
1957272 2 DB|| 7 2.50 6.00 6.0072.500 x x Heavy Duty End 1.000
6Y4277 1 DB/| 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit RH 1.000 x 3.54 2.44 3.25 3.25 ...2nd Row1.000 x 3.5
6Y4278 1 DB|\ 7 3.69 4.00 4.00 117.20 53.1631.625 x 13.000 x 23.300Level Cut End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1130334 1 DB/|Level Cut End Bit RH
1130336 1Level Cut End Bit LH
1130332 1 74.750 x x Heavy Duty Mining End Bit 1.000
1130333 1 74.750 x x Heavy Duty Mining End Bit 1.000
1006356 2 DB|| 4 7.88 6.00 18.00 282.00 127.911.750 x 13.000 x 45.750Sole Plate 1.000
834 G Serial Number:7J2960 3 DB|| 6 3.75 6.00 6.00 211.70 96.031.625 x 13.000 x 37.500Center 1.000
1380791 3 DB|| 6 3.75 6.00 6.00 309.00 140.162.500 x x Extra Heavy Duty Center 1.000
1517476 1 DB// 7 11.24 3.00 6.00 300.10 136.121.750 x 13.000 x 52.483Level Cut End Bit RH 1.000
1517477 1 DB\\ 7 11.24 3.00 6.00 300.10 136.121.750 x 13.000 x 52.483Level Cut End Bit LH 1.000
1380792 1 DB|| 406.00 184.162.500 x x Heavy Duty Mining End Bit
1380793 1 DB|| 406.00 184.162.500 x x Heavy Duty Mining End Bit
1006356 2 DB|| 4 7.88 6.00 18.00 282.00 127.911.750 x 13.000 x 45.750Sole Plate 1.000
834 H Serial Number:7J2960 3 DB|| 6 3.75 6.00 6.00 211.70 96.0361.625 x 13.000 x 37.500Center 1.000 x 3
1380791 3 DB|| 6 3.75 6.00 6.00 309.00 140.1662.500 x x Extra Heavy Duty Center 1.000 x 3
1517476 1 DB// 7 11.24 3.00 6.00 300.10 136.1271.750 x 13.000 x 52.483Level Cut End Bit RH 1.000 x 3
1517477 1 DB\\ 7 11.24 3.00 6.00 300.10 136.1271.750 x 13.000 x 52.483Level Cut End Bit LH 1.000 x 3
1380792 1 DB|| 406.00 184.1672.500 x x Heavy Duty Mining End Bit x 3
1380793 1 DB|| 406.00 184.1672.500 x x Heavy Duty Mining End Bit x 3
1856509 2 DB|| 7 1.63 6.00 6.00 180.30 81.7871.750 x 10.000 x 39.250Sole Plate 0.875 x 2.75
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
834 BALDERSONSerial Number:
1285695 2 DB|| 72.375 x x Wide Center (Offset Holes)
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 8©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1285696 1 DB|> 52.375 x x Wide End (Offset Holes)
1285697 1 DB<| 52.375 x x Wide End (Offset Holes)
1247284 1 72.375 x x End Bit (Long Side) RH
1247285 1 72.375 x x End Bit (Long Side) LH
1282870 1 72.375 x x End Bit (Short Side) RH
1282871 1 72.375 x x End Bit (Short Side) LH
844 BALDERSONSerial Number:
4T6378 1 DB|| 6 2.75 6.00 6.00 136.50 61.9261.125 x 13.000 x 35.500Center 1.000 x 3.25
6Y5540 2 DB|> 5 2.88 6.00 6.00 117.70 53.3951.125 x 13.000 x 31.500Center 1.000 x 3.25
4T6386 2 DB|| 7 2.50 6.00 6.00 157.90 71.6271.125 x 13.000 x 41.000Center 1.000 x 3.25
9W6092 1 DB|| 6 2.75 6.00 6.00 168.50 76.4361.375 x 13.000 x 35.500Heavy Duty Center 1.000 x 3.25
7T9125 2 DB|> 5 2.88 6.00 6.00 145.70 66.0951.375 x 13.000 x 31.500Heavy Duty Center 1.000 x 3.25
9W4500 2 DB|| 7 2.50 6.00 6.00 195.00 88.4571.375 x 13.000 x 41.000Heavy Duty Center 1.000 x 3.25
1359669 1 EBHC 5 5Level Cut End Bit RH 1.000 x 3.25
1359670 1 EBHC 5 5Level Cut End Bit LH 1.000 x 3.25
1359668 3 DB|| 7 3.00 6.00 6.00 351.00 159.212.000 x 16.000 x 41.875Sole Plate 1.375
844 BALDERSONSerial Number:
7J2980 1 DB|| 7 2.50 6.00 6.00 231.10 104.8331.625 x 13.000 x 41.000Center 1.000 x 3.5
9W3927 2 DB|> 5 2.88 6.00 6.00 186.70 84.6931.750 x 13.000 x 31.500End 1.000 x 3.5
1122475 2 DB|| 6 2.75 6.00 6.00 213.00 96.6231.750 x 13.000 x 35.500End 1.000 x 3.5
8E4197 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196 1 EBC 7 3.61 4.00 4.00 113.40 51.4431.500 x 15.371 x 23.496Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540 1 EBC 7 3.61 4.00 4.00 172.70 78.3431.755 x 15.495 x 24.115Cast End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
8E4197HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4196HC 1 EBHC 7 3.56 4.00 4.00 160.60 72.8532.000 x 16.000 x 24.000Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4539HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit RH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
8E4540HC 1 EBHC 7 3.63 4.00 4.00 185.30 84.0532.250 x 15.472 x 23.898Hot Cup End Bit LH 1.000 x 3.54 2.38 3.25 3.25 ...2nd Row1.000 x 3.5
1003135 1 DB/| 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003136 1 DB|\ 7 3.61 4.00 4.00 131.10 59.4731.750 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003137 1 DB/| 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit RH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1003138 1 DB|\ 7 3.61 4.00 4.00 185.30 84.0532.500 x 13.000 x 23.000Level Cut End Bit LH 1.000 x 3.54 2.36 3.25 3.25 ...2nd Row1.000 x 3.5
1359668 3 DB|| 7 3.00 6.00 6.00 351.00 159.212.000 x 16.000 x 41.875Sole Plate 1.375
844 AUSTRALIANSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 9©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W3928 3 DB|| 6 2.88 6.00 6.00 267.20 121.2061.750 x 16.000 x 35.750Center 1.250 x 4.125
9W6657 2 DB|> 5 4.38 6.00 6.00 242.80 110.1351.750 x 16.000 x 33.813End 1.250 x 4.125
1359625 3 DB|| 6 2.88 6.00 6.00 341.00 154.6862.375 x 16.000 x 35.750Center 1.250 x 4.125
8E2086 2 DB|> 5 5.44 6.00 6.00 331.10 150.1852.375 x 16.000 x 33.813End 1.250 x 4.125
8E4199 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541 1 EBC 7 3.11 7.09 2.95 275.57 125.0034.809 x 18.421 x 28.418Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542 1 EBC 7 3.11 7.09 2.95 280.80 127.3734.809 x 18.421 x 28.418Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755941 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755942 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4199HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.594Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003131 1 DB/| 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003132 1 DB|\ 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003133 1 DB/| 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003134 1 DB|\ 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1368755 1 DB/| 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 5.95 7.09 ...2nd Row1.250 x 4.125
1368754 1 DB|\ 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
9W3928 3 DB|| 6 2.88 6.00 6.00 267.20 121.2061.750 x 16.000 x 35.750Sole Plate 1.250 x 4.125
9W6657 2 DB|> 5 4.38 6.00 6.00 242.80 110.1351.750 x 16.000 x 33.813Sole Plate 1.250 x 4.125
1359625 3 DB|| 6 2.88 6.00 6.00 341.00 154.6862.375 x 16.000 x 35.750HD Sole Plate 1.250 x 4.125
8E2086 2 DB|> 5 5.44 6.00 6.00 331.10 150.1852.375 x 16.000 x 33.813HD Sole Plate 1.250 x 4.125
690 BALDERSONSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 10©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W4398 2 DB|> 5 2.88 6.00 6.00 145.40 65.9551.375 x 13.000 x 31.500Center 1.000 x 3.5
7T9126 2 DB|| 9 2.63 6.00 6.00 253.30 114.8991.375 x 13.000 x 53.250Center 1.000 x 3.5
9W6092 2 DB|| 6 2.75 6.00 6.00 168.50 76.4361.375 x 13.000 x 35.500Center 1.000 x 3.5
9W3927 2 DB|> 5 2.88 6.00 6.00 186.70 84.6951.750 x 13.000 x 31.500Heavy Duty Center 1.000 x 3.5
9W4507 2 DB|| 9 2.63 6.00 6.00 287.00 130.1891.625 x 13.000 x 53.250Heavy Duty Center 1.000 x 3.5
7J2959 2 DB|| 8 2.75 6.00 6.00 199.90 90.6761.625 x 13.000 x 35.500Heavy Duty Center 1.000 x 3.5
1359698 1 EBHC 6 2.02 5.00 6.00 93.00 42.1831.375 x 13.000 x 22.000Hot Cup End Bit RH 1.000 x 3.53 2.89 6.00 6.00 ...2nd Row1.000 x 3.5
1359699 1 EBHC 6 2.02 5.00 6.00 93.00 42.1831.375 x 13.000 x 22.000Hot Cup End Bit LH 1.000 x 3.53 2.89 6.00 6.00 ...2nd Row1.000 x 3.5
1359668 3 DB|| 7 3.00 6.00 6.00 351.00 159.212.000 x 16.000 x 41.875Sole Plate 1.375
690 BALDERSONSerial Number:
6Y0018 3 DB|| 9 2.94 3.00 3.00 309.90 140.5791.750 x 16.000 x 41.875Center 1.250 x 4.125
9W6657 2 DB|> 5 4.38 6.00 6.00 242.80 110.1351.750 x 16.000 x 33.813End 1.250 x 4.125
6Y0023 3 DB|| 9 2.94 3.00 3.00 415.10 188.2992.375 x 16.000 x 41.875Heavy Duty Center 1.250 x 4.125
8E2086 2 DB|> 5 5.44 6.00 6.00 331.10 150.1852.375 x 16.000 x 33.813Heavy Duty End 1.250 x 4.125
8E4199 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541 1 EBC 7 3.11 7.09 2.95 275.57 125.0034.809 x 18.421 x 28.418Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542 1 EBC 7 3.11 7.09 2.95 280.80 127.3734.809 x 18.421 x 28.418Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755941 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755942 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4199HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.594Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003131 1 DB/| 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003132 1 DB|\ 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 11©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1003133 1 DB/| 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003134 1 DB|\ 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1368755 1 DB/| 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 5.95 7.09 ...2nd Row1.250 x 4.125
1368754 1 DB|\ 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1359668 3 DB|| 7 3.00 6.00 6.00 351.00 159.212.000 x 16.000 x 41.875Sole Plate 1.375
854 BALDERSONSerial Number:
7J2966 3 DB|| 7 2.88 6.00 6.00 235.50 106.8271.625 x 13.000 x 41.750Center 1.000 x 3.5
1359671 2 DB|> 8End x 3.5
1359672 1 EBHC 5 5RH End Bit With Edge 1.000 x 3.5
1359673 1 EBHC 5 5LH End Bit With Edge 1.000 x 3.5
1359668 5 DB|| 7 3.00 6.00 6.00 351.00 159.212.000 x 16.000 x 41.875Sole Plate 1.375
854 BALDERSONSerial Number:
9W6658 4 DB|| 5 4.69 6.00 6.00 247.80 112.4051.750 x 16.000 x 33.375Heavier Center 1.250 x 4.125
9W6657 2 DB|> 5 4.38 6.00 6.00 242.80 110.1351.750 x 16.000 x 33.813Heavier End 1.250 x 4.125
8E2087 4 DB|| 5 4.69 6.00 6.00 338.00 153.3152.375 x 16.000 x 33.375Heavy Duty Center 1.250 x 4.125
8E2086 2 DB|> 5 5.44 6.00 6.00 331.10 150.1852.375 x 16.000 x 33.813Heavy Duty End 1.250 x 4.125
8E2087-24 4 DB|| 5 4.69 6.00 6.00 414.70 188.1053.000 x 16.000 x 33.375Extra Heavy Duty Center 1.250 x 4.125
1359579 2 DB|> 5 4.38 6.00 6.00 409.00 185.5253.000 x 16.000 x 33.813Extra Heavy Duty End 1.250 x 4.125
8E4199 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198 1 EBC 7 3.11 7.09 2.95 195.00 88.4533.919 x 19.993 x 28.991Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541 1 EBC 7 3.11 7.09 2.95 275.57 125.0034.809 x 18.421 x 28.418Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542 1 EBC 7 3.11 7.09 2.95 280.80 127.3734.809 x 18.421 x 28.418Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755941 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
2755942 1 EBC 7 3.11 7.09 2.95 319.00 144.7034.602 x 18.925 x 28.346Extra Extended Wear Cast End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4199HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4198HC 1 EBHC 7 3.11 7.09 2.95 233.20 105.7832.000 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4541HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
8E4542HC 1 EBHC 7 3.11 7.09 2.95 260.80 118.3032.250 x 19.000 x 29.000Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4689 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.594Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688 1 EBLC 7 3.11 7.09 2.95 255.20 115.7632.500 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 12©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Wheel Dozers/Compactors
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7T4689-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
7T4688-24 1 EBHC 7 3.11 7.09 2.95 305.70 138.6633.000 x 18.000 x 27.500Hot Cup End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003131 1 DB/| 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003132 1 DB|\ 7 3.11 7.09 2.95 178.70 81.0631.750 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003133 1 DB/| 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1003134 1 DB|\ 7 3.11 7.09 2.95 242.70 110.0932.375 x 16.000 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1368755 1 DB/| 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit RH 1.250 x 4.1254 2.01 5.95 7.09 ...2nd Row1.250 x 4.125
1368754 1 DB|\ 7 3.11 7.09 2.95 304.00 137.8933.000 x 14.250 x 27.000Level Cut End Bit LH 1.250 x 4.1254 2.01 2.95 7.09 ...2nd Row1.250 x 4.125
1359668 4 DB|| 7 3.00 6.00 6.00 351.00 159.212.000 x 16.000 x 41.875Sole Plate 1.375
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 13©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose5G8308Serial Number:
5G6133 1 WOSB 26Base Edge With Segment Holes 128.30 58.200.750 x 7.500 x 84.660
5G3085 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 129.60 58.790.750 x 7.500 x 84.660
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
4T2913 1 DB|| 3 11.31 14.44 14.44 99.00 44.9130.750 x 10.000 x 51.500Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957134 1 DB|| 3 7.15 14.46 11.1331.000 x 10.000 x 35.678HD Intermediate End RH 0.750 x 2.25
1957133 1 DB|| 4 2.94 11.13 14.4641.000 x 10.000 x 50.138HD Intermediate End LH 0.750 x 2.25
TEETH 7J200 or J225 Options
1282873 6 DB|| 2 1.94 6.50 16.00 7.2620.750 x 8.000 x 10.375Segment 0.750 x 2.25
7T8935 6 DB|| 2 1.94 6.50 1.94 20.10 9.1220.750 x 10.000 x 10.375Wider Segment 0.750 x 2.25
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose5G5762Serial Number:
5G5764 1 WOSBBase Edge Without Holes 0.750 x 7.500 x 87.343
5G5770 1 IRRCorner no holes RH
5G5769 1 IRRCorner no holes LH
TEETH 8J200 Options
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose5G7599Serial Number:
5G8763 1 WOSB 24Base Edge With Segment Holes 134.70 61.100.750 x 7.500 x 89.180
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
9W8694 1 DB|| 3 12.44 15.56 15.56 109.90 49.8530.750 x 10.000 x 56.000Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957140 1 DB|| 3 7.72 11.15 15.6031.000 x 10.000 x 37.406HD Intermediate End RH 0.750 x 2.25
1957139 1 DB|| 4 2.94 11.15 15.6041.000 x 10.000 x 52.426HD Intermediate End LH 0.750 x 2.25
TEETH 7J200 or J225 Options
1282872 4 DB|| 2 1.99 8.78 1.99 20.00 9.0720.750 x 8.000 x 12.750Center Segment 0.750 x 2.25
1282873 2 DB|| 2 1.94 6.50 16.00 7.2620.750 x 8.000 x 10.375End Segment 0.750 x 2.25
9W9640 4 DB|| 2 1.99 8.78 1.99 24.00 10.8920.750 x 10.000 x 12.750Wider Segment 0.750 x 2.25
7T8935 2 DB|| 2 1.94 6.50 1.94 20.10 9.1220.750 x 10.000 x 10.375Wider Segment 0.750 x 2.25
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose8G8524Serial Number:
5G8526 1 WOSBBase Edge Without Holes 0.750 x 7.500 x 91.654
5G5770 1 IRRCorner no holes RH
5G5769 1 IRRCorner no holes LH
TEETH 8J200 Options
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose9V8954 9V8955 9V8958 9V8959Serial Number:
9V6572 1 WOSB 28Base Edge With Segment Holes 241.80 109.681.000 x 9.650 x 93.310
5V4670 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 244.70 110.991.000 x 9.625 x 93.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0295 2 DB|| 3 6.50 13.25 13.25 108.20 49.0831.000 x 11.000 x 40.375Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3486 1 SB|| 3 7.38 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR RH 1.000 x 2.75
9W3487 1 SB|| 3 6.50 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose9V8956 9V8957 9V5960 9V5961Serial Number:
9V9755BASE 1 SB||Base Edge Without Holes 1.000 x 9.600 x 95.925
4V8285 1 IRRCorner no holes RH
4V8286 1 IRRCorner no holes LH
TEETH 8J250 or J300 Options
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose1718131 1718132 1718134Serial Number:
5G8342 1 WOSB 28Base Edge With Segment Holes 141.20 64.050.750 x 7.500 x 93.100
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
9W8620 1 DB|| 4 10.13 13.25 13.25 117.50 53.3040.750 x 10.000 x 60.000Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957137 2 DB|| 4 2.95 11.14 13.25 123.10 55.8441.000 x 10.000 x 47.120HD Center 0.750 x 2.25
TEETH 8J200 or J225 Options
1282873 7 DB|| 2 1.94 6.50 16.00 7.2620.750 x 8.000 x 10.375Segment 0.750 x 2.25
7T8935 7 DB|| 2 1.94 6.50 1.94 20.10 9.1220.750 x 10.000 x 10.375Wider Segment 0.750 x 2.25
IT12 IT14 IT24 IT26 IT28 IT38 Penetration1718133 1718135Serial Number:
5G8912 1 SB||Base Edge Without Holes 0.750 x 7.500 x 95.866
TEETH 8J200 Options
IT14 G H Penetration1718141Serial Number:
1281489 1Base Edge Without Holes 0.750 x 7.500 x 96.614
TEETH 8J250 Options
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose4E2474Serial Number:
4E0659 1 WOSB 28Base Edge With Segment Holes 251.10 113.901.000 x 9.650 x 99.350
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E4567 2 DB|| 3 7.00 14.13 14.13 116.70 52.9331.000 x 11.000 x 43.500Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1356728 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR RH 1.000 x 2.75
1356729 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
8E4569 7 DB|| 2 1.38 7.00 1.38 25.60 11.6121.000 x 11.000 x 9.750Segment 1.000 x 2.75
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose1718145Serial Number:
4E2483 1 WOSBBase Edge Without Holes 268.80 121.931.000 x 10.000 x 102.100
4V8285 1 IRRCorner no holes RH
4V8286 1 IRRCorner no holes LH
TEETH 8J250 or J300 Options
IT12 IT14 IT24 IT26 IT28 IT38 General Purpose1243468 1243469 1274920 1274921Serial Number:
1052345 1 WOSB 28Base Edge With Segment Holes 256.10 116.171.000 x 9.646 x 105.551
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1073746 2 DB|| 3 7.44 15.00 15.00 125.00 56.7031.000 x 11.000 x 46.563Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1073746HARR 1 HA|| 4 7.44 15.00 15.00 192.00 87.0941.125 x 10.000 x 53.002HA Center 1.000 x 2.75
1073746HARL 1 HA|| 4 4.13 11.44 15.00 192.00 87.0941.125 x 10.000 x 53.002HA Center 1.000 x 2.75
1386425 2 DB|| 3 7.44 15.00 15.00 168.50 76.4331.375 x 11.000 x 46.563HD Center 1.000 x 2.75
1386560 2 DB|| 2 5.56 2.44 27.70 12.5621.375 x 13.563 x 6.250HD End 1.000 x 2.75
1073298 1 SB|| 3 7.44 15.00 15.00 100.18 45.4431.000 x 8.000 x 46.563C/IMP Center NR RH 1.000 x 2.75
1073299 1 SB|| 3 9.13 15.00 15.00 100.20 45.4531.000 x 8.000 x 46.563C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6695 7 DB|| 2 1.38 7.69 1.38 27.40 12.4321.000 x 11.000 x 10.437Segment 1.000 x 2.75
1321037 7 DB|| 2 1.38 7.69 1.38 39.00 17.6921.375 x 11.000 x 10.438HD Segment 1.000 x 2.75
4T6695HA 7 HA|| 2 1.38 7.69 1.38 33.60 15.2421.375 x 10.875 x 10.438HA Segment (Cast) 1.000 x 2.75
IT62 GII H Material Handling1670046 1670045Serial Number:
1414847 1 WOSB 30Base Edge With Segment Holes 402.20 182.431.250 x 11.130 x 113.620
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1399230 2 DB|| 3 8.00 16.31 16.31 209.00 94.8031.180 x 14.170 x 50.500Center 1.000 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 3©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1359666 2 DB|| 3 8.00 16.31 16.31 260.70 118.2531.375 x 14.250 x 50.500HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
1399230HAN 3 HA|| 2 7.92 16.31 129.50 58.7421.625 x 10.375 x 32.153HA Center (Cast) 1.000 x 3
4T8101HA 2 HA|| 3 3.25 2.69 2.69 48.60 22.0431.625 x 15.125 x 8.375HA End (Cast) 1.000 x 3
1380672 1 SB|| 3 8.00 16.31 16.31 163.00 73.9431.125 x 11.000 x 50.500C/IMP Center NR RH 1.000 x 3
1380673 1 SB|| 3 9.88 16.31 16.31 163.00 73.9431.125 x 11.000 x 50.500C/IMP Center NR LH 1.000 x 3
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR RH 1.000 x 3
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR LH 1.000 x 3
TEETH 8J300 Options
1324715 7 DB|| 2 1.38 8.19 1.38 46.70 21.1821.375 x 12.000 x 10.938Segment 1.000 x 3
1407601 7 DB|| 2 1.66 8.19 46.90 21.2721.180 x 14.170 x 11.500Wider Segment 1.000 x 3
902 General Purpose, Multi-Purpose, High Dump1388941 1388912 1501917Serial Number:
1388938 1 WOSBBase Edge
9R5205 1 IRRCorner no holes RH 5.80 2.630.750 x 6.000 x 5.563
9R5206 1 IRRCorner no holes LH 5.80 2.630.750 x 6.000 x 5.563
1324723 1 DB|| 13 3.03 5.35 5.35 70.50 31.98130.625 x 6.500 x 70.470Bolt On (Flat Head Screws) 0.688 x 2
1324723PB 1 DB|| 13 3.03 5.35 5.35 73.00 33.11130.625 x 6.500 x 70.315Bolt On (Plow Bolts) 0.625 x 2.25
1324720 7 UNITOO 2 2.38 4.00 1.812.000 x 2.313 x 9.188Bolt on Unitooth 0.625
902 Stone Sieve1486412Serial Number:
1605334 1 WOSB 20Base Edge For Bolt-on Edges or Teeth 110.00 49.900.750 x 8.000 x 70.157
9R5205 1 IRRCorner no holes RH 5.80 2.630.750 x 6.000 x 5.563
9R5206 1 IRRCorner no holes LH 5.80 2.630.750 x 6.000 x 5.563
1324723 1 DB|| 13 3.03 5.35 5.35 70.50 31.98130.625 x 6.500 x 70.470Bolt On (Flat Head Screws) 0.688 x 2
1324723PB 1 DB|| 13 3.03 5.35 5.35 73.00 33.11130.625 x 6.500 x 70.315Bolt On (Plow Bolts) 0.625 x 2.25
1324720 7 UNITOO 2 2.38 4.00 1.812.000 x 2.313 x 9.188Bolt on Unitooth 0.625
902 Light Material, Side Dump, Grapple1499261 1417263 1843268Serial Number:
1388932 1 WOSB 20Base Edge For Bolt-on Edges or Teeth 88.00 39.920.750 x 6.000 x 74.213
1324724 1 DB|| 13 2.95 5.71 5.71 77.00 34.93130.625 x 6.500 x 74.410Bolt On (Flat Head Screws) 0.625 x 2
1324724PB 1 DB|| 13 2.95 5.71 5.71 77.00 34.93130.625 x 6.500 x 74.409Bolt On (Plow Bolts) 0.625 x 2.25
906 General Purpose, Multi-Purpose, High Dump1388931 1388914 1414990Serial Number:
1388932 1 WOSB 20Base Edge For Bolt-on Edges or Teeth 88.00 39.920.750 x 6.000 x 74.213
9R5205 1 IRRCorner no holes RH 5.80 2.630.750 x 6.000 x 5.563
9R5206 1 IRRCorner no holes LH 5.80 2.630.750 x 6.000 x 5.563
1324724 1 DB|| 13 2.95 5.71 5.71 77.00 34.93130.625 x 6.500 x 74.410Bolt On (Flat Head Screws) 0.625 x 2
1324724PB 1 DB|| 13 2.95 5.71 5.71 77.00 34.93130.625 x 6.500 x 74.409Bolt On (Plow Bolts) 0.625 x 2.25
1324720 7 UNITOO 2 2.38 4.00 1.812.000 x 2.313 x 9.188Bolt on Unitooth 0.625
906 Stone Sieve1485385Serial Number:
1605335 1 WOSBBase Edge
9R5205 1 IRRCorner no holes RH 5.80 2.630.750 x 6.000 x 5.563
9R5206 1 IRRCorner no holes LH 5.80 2.630.750 x 6.000 x 5.563
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 4©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1324724 1 DB|| 13 2.95 5.71 5.71 77.00 34.93130.625 x 6.500 x 74.410Bolt On (Flat Head Screws) 0.625 x 2
1324724PB 1 DB|| 13 2.95 5.71 5.71 77.00 34.93130.625 x 6.500 x 74.409Bolt On (Plow Bolts) 0.625 x 2.25
1324720 7 UNITOO 2 2.38 4.00 1.812.000 x 2.313 x 9.188Bolt on Unitooth 0.625
906 Light Material1473152Serial Number:
1521051 1 WOSBBase Edge
9R5205 1 IRRCorner no holes RH 5.80 2.630.750 x 6.000 x 5.563
9R5206 1 IRRCorner no holes LH 5.80 2.630.750 x 6.000 x 5.563
1324719 1 DB|| 13 2.50 6.00 6.00 80.00 36.29130.625 x 6.500 x 77.000Bolt On (Flat Head Screws) 0.625 x 2
1324719PB 1 DB|| 13 2.50 6.00 6.00 80.00 36.29130.625 x 6.500 x 77.000Bolt On (Plow Bolts) 0.625 x 2.25
906 Side Dump, Grapple1417265 1860153Serial Number:
1388937 1 WOSB 20Base Edge 124.50 56.470.750 x 8.000 x 81.102
1324725 1 DB|| 13 3.15 6.30 6.30 82.30 37.33130.625 x 6.500 x 81.890Bolt On (Flat Head Screws) 0.625 x 2
1324725PB 1 DB|| 13 3.15 6.30 6.30 85.00 38.56130.625 x 6.500 x 81.889Bolt On (Plow Bolts) 0.625 x 2.25
908 Gen Purpose, Light Material, Stone Sieve, High Dum1388905 1473153 1485386 1414992Serial Number:
1388937 1 WOSB 20Base Edge 124.50 56.470.750 x 8.000 x 81.102
9R5205 1 IRRCorner no holes RH 5.80 2.630.750 x 6.000 x 5.563
9R5206 1 IRRCorner no holes LH 5.80 2.630.750 x 6.000 x 5.563
1324725 1 DB|| 13 3.15 6.30 6.30 82.30 37.33130.625 x 6.500 x 81.890Bolt On (Flat Head Screws) 0.625 x 2
1324725PB 1 DB|| 13 3.15 6.30 6.30 85.00 38.56130.625 x 6.500 x 81.889Bolt On (Plow Bolts) 0.625 x 2.25
1324720 7 UNITOO 2 2.38 4.00 1.812.000 x 2.313 x 9.188Bolt on Unitooth 0.625
908 Multi-Purpose1388916Serial Number:
1471040 1 WOSBBase Edge
9R5205 1 IRRCorner no holes RH 5.80 2.630.750 x 6.000 x 5.563
9R5206 1 IRRCorner no holes LH 5.80 2.630.750 x 6.000 x 5.563
1324725 1 DB|| 13 3.15 6.30 6.30 82.30 37.33130.625 x 6.500 x 81.890Bolt On (Flat Head Screws) 0.625 x 2
1324725PB 1 DB|| 13 3.15 6.30 6.30 85.00 38.56130.625 x 6.500 x 81.889Bolt On (Plow Bolts) 0.625 x 2.25
1324720 7 UNITOO 2 2.38 4.00 1.812.000 x 2.313 x 9.188Bolt on Unitooth 0.625
910 General Purpose6S6504 6S8657Serial Number:
6S6500 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 129.60 58.790.750 x 7.500 x 84.660
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
4T2920 1 DB|| 3 6.75 12.25 12.25 73.00 33.1130.750 x 10.000 x 38.000Center 0.750 x 2.25
4T2918 2 DB|| 2 5.50 12.25 5.50 44.00 19.9620.750 x 10.000 x 23.250End 0.750 x 2.25
TEETH 7J200 or J225 Options
910 General Purpose5G4088 5G3080 5G6180Serial Number:
5G6133 1 WOSB 26Base Edge With Segment Holes 128.30 58.200.750 x 7.500 x 84.660
5G3085 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 129.60 58.790.750 x 7.500 x 84.660
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 5©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T2913 1 DB|| 3 11.31 14.44 14.44 99.00 44.9130.750 x 10.000 x 51.500Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957134 1 DB|| 3 7.15 14.46 11.1331.000 x 10.000 x 35.678HD Intermediate End RH 0.750 x 2.25
1957133 1 DB|| 4 2.94 11.13 14.4641.000 x 10.000 x 50.138HD Intermediate End LH 0.750 x 2.25
TEETH 7J200 or J225 Options
1282873 6 DB|| 2 1.94 6.50 16.00 7.2620.750 x 8.000 x 10.375Segment 0.750 x 2.25
7T8935 6 DB|| 2 1.94 6.50 1.94 20.10 9.120.750 x 10.000 x 10.375Wider Segment 0.750
910 E F General Purpose713193Serial Number:
5G8763 1 WOSB 24Base Edge With Segment Holes 134.70 61.100.750 x 7.500 x 89.180
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
9W8694 1 DB|| 3 12.44 15.56 15.56 109.90 49.8530.750 x 10.000 x 56.000Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957140 1 DB|| 3 7.72 11.15 15.6031.000 x 10.000 x 37.406HD Intermediate End RH 0.750 x 2.25
1957139 1 DB|| 4 2.94 11.15 15.6041.000 x 10.000 x 52.426HD Intermediate End LH 0.750 x 2.25
TEETH 7J200 or J225 Options
1282872 4 DB|| 2 1.99 8.78 1.99 20.00 9.0720.750 x 8.000 x 12.750Center Segment 0.750 x 2.25
1282873 2 DB|| 2 1.94 6.50 16.00 7.2620.750 x 8.000 x 10.375End Segment 0.750 x 2.25
9W9640 4 DB|| 2 1.99 8.78 1.99 24.00 10.8920.750 x 10.000 x 12.750Wider Segment 0.750 x 2.25
7T8935 2 DB|| 2 1.94 6.50 1.94 20.10 9.1220.750 x 10.000 x 10.375Wider Segment 0.750 x 2.25
910 E F General Purpose9U4718Serial Number:
5G8342 1 WOSB 28Base Edge With Segment Holes 141.20 64.050.750 x 7.500 x 93.100
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
9W8620 1 DB|| 4 10.13 13.25 13.25 117.50 53.3040.750 x 10.000 x 60.000Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957137 2 DB|| 4 2.95 11.14 13.25 123.10 55.8441.000 x 10.000 x 47.120HD Center 0.750 x 2.25
TEETH 8J200 or J225 Options
1282873 7 DB|| 2 1.94 6.50 16.00 7.2620.750 x 8.000 x 10.375Segment 0.750 x 2.25
7T8935 7 DB|| 2 1.94 6.50 1.94 20.10 9.1220.750 x 10.000 x 10.375Wider Segment 0.750 x 2.25
910 E F Penetration7I3194Serial Number:
5G8912 1 SB||Base Edge Without Holes 0.750 x 7.500 x 95.866
TEETH 8J200 Options
910 Multi-Purpose6S4521Serial Number:
5G2809 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 127.80 57.970.750 x 7.500 x 81.875
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
4T8796 1 DB|| 3 10.69 13.75 13.75 95.90 43.5030.750 x 10.000 x 48.875Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957132 1 DB|| 3 2.94 11.13 13.7531.000 x 10.000 x 34.626HD Intermediate End RH 0.750 x 2.25
1957131 1 DB|| 4 2.94 11.13 13.7541.000 x 10.000 x 48.376HD Intermediate End LH 0.750 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 6©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6S4738 1 DB|| 78.00 35.380.625 x 6.000 x 82.000Multi purpose dozer center
TEETH 7J200 or J225 Options
910 Multi-Purpose6S4521Serial Number:
6S6500 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 129.60 58.790.750 x 7.500 x 84.660
4T2920 1 DB|| 3 6.75 12.25 12.25 73.00 33.1130.750 x 10.000 x 38.000Center 0.750 x 2.25
4T2918 2 DB|| 2 5.50 12.25 5.50 44.00 19.9620.750 x 10.000 x 23.250End 0.750 x 2.25
6S4738 1 DB|| 78.00 35.380.625 x 6.000 x 82.000Multi purpose dozer center
TEETH 7J200 or J225 Options
914 G General Purpose1718128 1718129Serial Number:
5G8342 1 WOSB 28Base Edge With Segment Holes 141.20 64.050.750 x 7.500 x 93.100
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
9W8620 1 DB|| 4 10.13 13.25 13.25 117.50 53.3040.750 x 10.000 x 60.000Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957137 2 DB|| 4 2.95 11.14 13.25 123.10 55.8441.000 x 10.000 x 47.120HD Center 0.750 x 2.25
TEETH 8J200 or J225 Options
1282873 7 DB|| 2 1.94 6.50 16.00 7.2620.750 x 8.000 x 10.375Segment 0.750 x 2.25
7T8935 7 DB|| 2 1.94 6.50 1.94 20.10 9.1220.750 x 10.000 x 10.375Wider Segment 0.750 x 2.25
914 G Penetration1718130Serial Number:
5G8912 1 SB||Base Edge Without Holes 0.750 x 7.500 x 95.866
TEETH 8J200 Options
916 Corner Guard System9C4940 8V7152 6W7769 8R2126 8R2127 9C4938 9C4939 6W5994 8V7153 1119634Serial Number:
9V6572 1 WOSB 28Base Edge With Segment Holes 241.80 109.681.000 x 9.650 x 93.310
5V4670 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 244.70 110.991.000 x 9.625 x 93.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0295 2 DB|| 3 6.50 13.25 13.25 108.20 49.0831.000 x 11.000 x 40.375Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3486 1 SB|| 3 7.38 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR RH 1.000 x 2.75
9W3487 1 SB|| 3 6.50 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
916 Penetration9C4941 9V9795Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 7©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9V9755BASE 1 SB||Base Edge Without Holes 1.000 x 9.600 x 95.925
TEETH 8J250 or J300 Options
918 F Penetration4E1724Serial Number:
9V9755BASE 1 SB||Base Edge Without Holes 1.000 x 9.600 x 95.925
TEETH 8J250 or J300 Options
920 Corner Guard System5V4662 5V4660Serial Number:
6W2984 1 WOSB 28Base Edge With Segment Holes 244.40 110.861.000 x 9.600 x 94.780
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0607 2 DB|| 3 6.75 13.75 13.75 109.90 49.8531.000 x 11.000 x 41.000Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3483 2 SB|| 3 6.75 13.75 13.75 94.60 42.9131.000 x 8.000 x 41.000C/IMP Center NR LH/RH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6694 5 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Center Segment 1.000 x 2.75
4T6693 2 DB|| 2 1.38 5.50 1.38 21.30 9.6621.000 x 11.000 x 8.250End Segment 1.000 x 2.75
1321035 5 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Center Segment 1.000 x 2.75
1321036 2 DB|| 2 1.38 5.50 1.38 32.00 14.5121.375 x 11.000 x 8.250HD End Segment 1.000 x 2.75
4T6694HA 5 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Center Segment 1.000 x 2.75
4T6693HA 2 HA|| 2 1.38 5.50 1.38 25.90 11.7521.375 x 10.875 x 8.250HA End Segment 1.000 x 2.75
920 General Purpose9K0574 9K7874Serial Number:
8K8161 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 225.00 102.061.000 x 9.000 x 96.000
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1465 1 DB|| 3 4.88 10.63 10.63 82.80 37.5631.000 x 11.000 x 31.000Center 1.000 x 2.75
1U1464 2 DB|| 3 5.50 10.63 10.63 86.20 39.1021.000 x 11.000 x 32.250End 1.000 x 2.75
1321026 1 DB|| 3 4.88 10.63 10.63 114.00 51.7131.375 x 11.000 x 31.000HD Center 1.000 x 2.75
1321027 2 DB|| 3 5.50 10.63 10.63 119.00 53.9821.375 x 11.000 x 32.250HD End 1.000 x 2.75
9W3469 1 SB|| 3 4.88 10.63 10.63 65.00 29.4831.000 x 8.000 x 31.000C/IMP Center NR 1.000 x 2.75
9W3470 1 SB|| 3 5.50 10.63 10.63 68.00 30.8421.000 x 8.000 x 32.250C/IMP End NR RH 1.000 x 2.75
9W3471 1 SB|| 3 5.50 10.63 10.63 68.00 30.8421.000 x 8.000 x 32.250C/IMP End NR LH 1.000 x 2.75
TEETH 9J250 or J300 Options
920 Flush Mounted Teeth9K8754Serial Number:
1V3916 1 WOSBBase Edge Without Holes 231.40 104.961.000 x 9.000 x 96.000
TEETH 9J250 or J300 Options
920 Multi-Purpose5V4659 5V4659Serial Number:
6W2984 1 WOSB 28Base Edge With Segment Holes 244.40 110.861.000 x 9.600 x 94.780
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 8©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0607 2 DB|| 3 6.75 13.75 13.75 109.90 49.8531.000 x 11.000 x 41.000Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3483 2 SB|| 3 6.75 13.75 13.75 94.60 42.9131.000 x 8.000 x 41.000C/IMP Center NR LH/RH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
4T8077 1 DB|| 15 4.88 6.00 6.00 120.10 54.48150.625 x 8.000 x 93.750Multi purpose dozer center 0.625 x 2
TEETH 8J250 or J300 Options
4T6694 5 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Center Segment 1.000 x 2.75
4T6693 2 DB|| 2 1.38 5.50 1.38 21.30 9.6621.000 x 11.000 x 8.250End Segment 1.000 x 2.75
1321035 5 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Center Segment 1.000 x 2.75
1321036 2 DB|| 2 1.38 5.50 1.38 32.00 14.5121.375 x 11.000 x 8.250HD End Segment 1.000 x 2.75
4T6694HA 5 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Center Segment 1.000 x 2.75
4T6693HA 2 HA|| 2 1.38 5.50 1.38 25.90 11.7521.375 x 10.875 x 8.250HA End Segment 1.000 x 2.75
920 Multi-Purpose9K6159 9K5692Serial Number:
8K8161 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 225.00 102.061.000 x 9.000 x 96.000
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1465 1 DB|| 3 4.88 10.63 10.63 82.80 37.5631.000 x 11.000 x 31.000Center 1.000 x 2.75
1U1464 2 DB|| 3 5.50 10.63 10.63 86.20 39.1021.000 x 11.000 x 32.250End 1.000 x 2.75
1321026 1 DB|| 3 4.88 10.63 10.63 114.00 51.7131.375 x 11.000 x 31.000HD Center 1.000 x 2.75
1321027 2 DB|| 3 5.50 10.63 10.63 119.00 53.9821.375 x 11.000 x 32.250HD End 1.000 x 2.75
9W3469 1 SB|| 3 4.88 10.63 10.63 65.00 29.4831.000 x 8.000 x 31.000C/IMP Center NR 1.000 x 2.75
9W3470 1 SB|| 3 5.50 10.63 10.63 68.00 30.8421.000 x 8.000 x 32.250C/IMP End NR RH 1.000 x 2.75
9W3471 1 SB|| 3 5.50 10.63 10.63 68.00 30.8421.000 x 8.000 x 32.250C/IMP End NR LH 1.000 x 2.75
4T8077 1 DB|| 15 4.88 6.00 6.00 120.10 54.48150.625 x 8.000 x 93.750Multi purpose dozer center 0.625 x 2
TEETH 9J250 or J300 Options
924 F Corner Guard System1119634 1119635Serial Number:
9V6572 1 WOSB 28Base Edge With Segment Holes 241.80 109.681.000 x 9.650 x 93.310
5V4670 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 244.70 110.991.000 x 9.625 x 93.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0295 2 DB|| 3 6.50 13.25 13.25 108.20 49.0831.000 x 11.000 x 40.375Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 9©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W3486 1 SB|| 3 7.38 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR RH 1.000 x 2.75
9W3487 1 SB|| 3 6.50 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
924 G GZ Corner Guard System1455166 1455165 1784665 1455163 1455162 1687535 1477331 1694872 1728568 1733635 1673963 2410935 2516Serial Number:
4E0659 1 WOSB 28Base Edge With Segment Holes 251.10 113.901.000 x 9.650 x 99.350
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
8E4567 2 DB|| 3 7.00 14.13 14.13 116.70 52.9331.000 x 11.000 x 43.500Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1356728 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR RH 1.000 x 2.75
1356729 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
8E4569 7 DB|| 2 1.38 7.00 1.38 25.60 11.6121.000 x 11.000 x 9.750Segment 1.000 x 2.75
9V4484 2 DB|| 8.00 3.630.625 x 8.000 x 6.500Weld-On Wear Plate
926 Corner Guard System9C8254 6W5556 9C6372 8R6169Serial Number:
9V6572 1 WOSB 28Base Edge With Segment Holes 241.80 109.681.000 x 9.650 x 93.310
5V4670 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 244.70 110.991.000 x 9.625 x 93.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0295 2 DB|| 3 6.50 13.25 13.25 108.20 49.0831.000 x 11.000 x 40.375Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3486 1 SB|| 3 7.38 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR RH 1.000 x 2.75
9W3487 1 SB|| 3 6.50 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 10©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
926 Corner Guard System4E0091 4E0092Serial Number:
4E0659 1 WOSB 28Base Edge With Segment Holes 251.10 113.901.000 x 9.650 x 99.350
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
8E4567 2 DB|| 3 7.00 14.13 14.13 116.70 52.9331.000 x 11.000 x 43.500Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1356728 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR RH 1.000 x 2.75
1356729 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
8E4569 7 DB|| 2 1.38 7.00 1.38 25.60 11.6121.000 x 11.000 x 9.750Segment 1.000 x 2.75
926 Penetration9C4905 9V9756Serial Number:
9V9755BASE 1 SB||Base Edge Without Holes 1.000 x 9.600 x 95.925
TEETH 8J250 or J300 Options
926 Penetration4E0090Serial Number:
4E2483 1 WOSBBase Edge Without Holes 268.80 121.931.000 x 10.000 x 102.100
TEETH 8J250 or J300 Options
928 F G GZ Corner Guard System4E0091 4E0092 1718136 1718137Serial Number:
4E0659 1 WOSB 28Base Edge With Segment Holes 251.10 113.901.000 x 9.650 x 99.350
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
8E4567 2 DB|| 3 7.00 14.13 14.13 116.70 52.9331.000 x 11.000 x 43.500Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1356728 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR RH 1.000 x 2.75
1356729 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
8E4569 7 DB|| 2 1.38 7.00 1.38 25.60 11.6121.000 x 11.000 x 9.750Segment 1.000 x 2.75
928 F G GZ Penetration4E0090 1718138Serial Number:
4E2483 1 WOSBBase Edge Without Holes 268.80 121.931.000 x 10.000 x 102.100
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 11©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J250 or J300 Options
930 Corner Guard System5V4656 5V4657Serial Number:
6W2984 1 WOSB 28Base Edge With Segment Holes 244.40 110.861.000 x 9.600 x 94.780
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0607 2 DB|| 3 6.75 13.75 13.75 109.90 49.8531.000 x 11.000 x 41.000Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3483 2 SB|| 3 6.75 13.75 13.75 94.60 42.9131.000 x 8.000 x 41.000C/IMP Center NR LH/RH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6694 5 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
4T6693 2 DB|| 2 1.38 5.50 1.38 21.30 9.6621.000 x 11.000 x 8.250End Segment 1.000 x 2.75
1321035 5 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
1321036 2 DB|| 2 1.38 5.50 1.38 32.00 14.5121.375 x 11.000 x 8.250HD End 1.000 x 2.75
4T6694HA 5 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
4T6693HA 2 HA|| 2 1.38 5.50 1.38 25.90 11.7521.375 x 10.875 x 8.250HA Segment (Cast) 1.000 x 2.75
930 General Purpose8K8989 8K9767Serial Number:
8K8161 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 225.00 102.061.000 x 9.000 x 96.000
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1465 1 DB|| 3 4.88 10.63 10.63 82.80 37.5631.000 x 11.000 x 31.000Center 1.000 x 2.75
1U1464 2 DB|| 3 5.50 10.63 10.63 86.20 39.1021.000 x 11.000 x 32.250End 1.000 x 2.75
1321026 1 DB|| 3 4.88 10.63 10.63 114.00 51.7131.375 x 11.000 x 31.000HD Center 1.000 x 2.75
1321027 2 DB|| 3 5.50 10.63 10.63 119.00 53.9821.375 x 11.000 x 32.250HD End 1.000 x 2.75
9W3469 1 SB|| 3 4.88 10.63 10.63 65.00 29.4831.000 x 8.000 x 31.000C/IMP Center NR 1.000 x 2.75
9W3470 1 SB|| 3 5.50 10.63 10.63 68.00 30.8421.000 x 8.000 x 32.250C/IMP End NR RH 1.000 x 2.75
9W3471 1 SB|| 3 5.50 10.63 10.63 68.00 30.8421.000 x 8.000 x 32.250C/IMP End NR LH 1.000 x 2.75
TEETH 9J250 or J300 Options
930 Flush Mounted Teeth9K8864Serial Number:
1V3916 1 WOSBBase Edge Without Holes 231.40 104.961.000 x 9.000 x 96.000
TEETH 9J250 or J300 Options
930 Multi-Purpose5V4653 5V4655Serial Number:
6W2984 1 WOSB 28Base Edge With Segment Holes 244.40 110.861.000 x 9.600 x 94.780
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 12©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0607 2 DB|| 3 6.75 13.75 13.75 109.90 49.8531.000 x 11.000 x 41.000Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3483 2 SB|| 3 6.75 13.75 13.75 94.60 42.9131.000 x 8.000 x 41.000C/IMP Center NR LH/RH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
4T8077 1 DB|| 15 4.88 6.00 6.00 120.10 54.48150.625 x 8.000 x 93.750Multi purpose dozer center 0.625 x 2
TEETH 8J250 or J300 Options
4T6694 5 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
4T6693 2 DB|| 2 1.38 5.50 1.38 21.30 9.6621.000 x 11.000 x 8.250End Segment 1.000 x 2.75
1321035 5 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
1321036 2 DB|| 2 1.38 5.50 1.38 32.00 14.5121.375 x 11.000 x 8.250HD End 1.000 x 2.75
4T6694HA 5 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
4T6693HA 2 HA|| 2 1.38 5.50 1.38 25.90 11.7521.375 x 10.875 x 8.250HA Segment (Cast) 1.000 x 2.75
930 Multi-Purpose9K6721 9K6717Serial Number:
8K8161 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 225.00 102.061.000 x 9.000 x 96.000
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1465 1 DB|| 3 4.88 10.63 10.63 82.80 37.5631.000 x 11.000 x 31.000Center 1.000 x 2.75
1U1464 2 DB|| 3 5.50 10.63 10.63 86.20 39.1021.000 x 11.000 x 32.250End 1.000 x 2.75
1321026 1 DB|| 3 4.88 10.63 10.63 114.00 51.7131.375 x 11.000 x 31.000HD Center 1.000 x 2.75
1321027 2 DB|| 3 5.50 10.63 10.63 119.00 53.9821.375 x 11.000 x 32.250HD End 1.000 x 2.75
9W3469 1 SB|| 3 4.88 10.63 10.63 65.00 29.4831.000 x 8.000 x 31.000C/IMP Center NR 1.000 x 2.75
9W3470 1 SB|| 3 5.50 10.63 10.63 68.00 30.8421.000 x 8.000 x 32.250C/IMP End NR RH 1.000 x 2.75
9W3471 1 SB|| 3 5.50 10.63 10.63 68.00 30.8421.000 x 8.000 x 32.250C/IMP End NR LH 1.000 x 2.75
4T8077 1 DB|| 15 4.88 6.00 6.00 120.10 54.48150.625 x 8.000 x 93.750Multi purpose dozer center 0.625 x 2
TEETH 9J250 or J300 Options
930 G Corner Guard System2568882 2568911 2410935 2397002 2545412 2410916 2526909 2397004 2526903 2568889 2568863 2568898Serial Number:
4E0659 1 WOSB 28Base Edge With Segment Holes 251.10 113.901.000 x 9.650 x 99.350
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
8E4567 2 DB|| 3 7.00 14.13 14.13 116.70 52.9331.000 x 11.000 x 43.500Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1356728 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR RH 1.000 x 2.75
1356729 1 SB|| 3 8.25 14.13 14.13 107.60 48.8131.000 x 8.000 x 43.500C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
8E4569 7 DB|| 2 1.38 7.00 1.38 25.60 11.6121.000 x 11.000 x 9.750Segment 1.000 x 2.75
930 G Penetration2410916 2515413 2526904Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 13©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4E2483 1 WOSBBase Edge Without Holes 268.80 121.931.000 x 10.000 x 102.100
TEETH 8J250 or J300 Options
933 General Purpose1106379 8Y4996 8Y4982Serial Number:
8Y4738 1 WOSB 30Base Edge With Segment Holes 118.10 53.570.750 x 7.500 x 76.876
5G8467 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 119.90 54.390.750 x 7.500 x 76.875
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
9W9943 1 DB|| 4 7.81 11.00 11.00 94.90 43.0540.750 x 10.000 x 48.500Center 0.750 x 2.25
9W9944 2 DB|| 2 3.00 8.69 3.00 28.60 12.9720.750 x 10.000 x 14.688End 0.750 x 2.25
TEETH 8J225 Options
6Y6362 7 DB|| 2 1.97 3.94 1.97 15.10 6.8520.750 x 10.000 x 7.874Segment 0.750 x 2.25
933 General Purpose1103833Serial Number:
5G3477 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 152.30 69.080.750 x 8.000 x 91.760
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
4T2915 1 DB|| 3 13.00 16.25 16.25 113.00 51.2630.750 x 10.000 x 58.500Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957136 1 DB|| 3 2.94 11.14 16.2231.000 x 10.000 x 38.346HD Intermediate End RH 0.750 x 2.25
1957135 1 DB|| 4 2.94 11.14 16.2241.000 x 10.000 x 54.566HD Intermediate End LH 0.750 x 2.25
TEETH 7J200 or J225 Options
933 Multi-Purpose1107541Serial Number:
8Y4738 1 WOSB 30Base Edge With Segment Holes 118.10 53.570.750 x 7.500 x 76.876
5G8467 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 119.90 54.390.750 x 7.500 x 76.875
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
9W9943 1 DB|| 4 7.81 11.00 11.00 94.90 43.0540.750 x 10.000 x 48.500Center 0.750 x 2.25
9W9944 2 DB|| 2 3.00 8.69 3.00 28.60 12.9720.750 x 10.000 x 14.688End 0.750 x 2.25
8Y5291 1 SE|| 0.625 x 6.000 x 76.610Multi purpose dozer center
TEETH 8J225 Options
6Y6362 7 DB|| 2 1.97 3.94 1.97 15.10 6.8520.750 x 10.000 x 7.874Segment 0.750 x 2.25
935 931 General Purpose5G2811Serial Number:
5G2808 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 112.00 50.800.750 x 7.500 x 72.000
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
4T2911 1 DB|| 4 7.10 10.28 10.28 88.00 39.9240.750 x 10.000 x 45.031Center 0.750 x 2.25
4T2910 2 DB|| 2 2.97 7.97 3.00 27.00 12.2520.750 x 10.000 x 13.938End 0.750 x 2.25
1957130 2 DB|| 4 2.94 7.95 10.2841.000 x 10.000 x 36.526HD Center 0.750 x 2.25
TEETH 8J200 or J225 Options
935 931 General Purpose6S6503Serial Number:
6S6501 1 WOSB 12Base Edge For Bolt-on Edges or Teeth 117.20 53.160.750 x 7.500 x 74.720
6S3237 1 IRRCorner no holes RH
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 14©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6S3238 1 IRRCorner no holes LH
4T2919 2 DB|| 3 5.35 12.80 12.80 71.00 32.2130.750 x 10.000 x 37.250Center 0.750 x 2.25
TEETH 6J200 or J225 Options
935 931 General Purpose5G0890Serial Number:
5G2395 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 116.80 52.980.750 x 7.500 x 74.730
6S3237 1 IRRCorner no holes RH
6S3238 1 IRRCorner no holes LH
4T2912 2 DB|| 4 4.72 9.61 9.61 72.00 32.6640.750 x 10.000 x 37.609Center 0.750 x 2.25
TEETH 8J200 or J225 Options
935 931 General Purpose5G8461 8Y4996 8Y4982 1106379Serial Number:
8Y4738 1 WOSB 30Base Edge With Segment Holes 118.10 53.570.750 x 7.500 x 76.876
5G8467 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 119.90 54.390.750 x 7.500 x 76.875
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
9W9943 1 DB|| 4 7.81 11.00 11.00 94.90 43.0540.750 x 10.000 x 48.500Center 0.750 x 2.25
9W9944 2 DB|| 2 3.00 8.69 3.00 28.60 12.9720.750 x 10.000 x 14.688End 0.750 x 2.25
1957138 2 DB|| 4 2.94 8.69 11.0041.000 x 10.000 x 39.064HD Center 0.750 x 2.25
TEETH 8J225 Options
6Y6362 7 DB|| 2 1.97 3.94 1.97 15.10 6.8520.750 x 10.000 x 7.874Segment 0.750 x 2.25
935 931 General Purpose6S6504 6S8657Serial Number:
6S6500 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 129.60 58.790.750 x 7.500 x 84.660
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
4T2920 1 DB|| 3 6.75 12.25 12.25 73.00 33.1130.750 x 10.000 x 38.000Center 0.750 x 2.25
4T2918 2 DB|| 2 5.50 12.25 5.50 44.00 19.9620.750 x 10.000 x 23.250End 0.750 x 2.25
TEETH 7J200 or J225 Options
935 931 General Purpose5G3475Serial Number:
5G3477 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 152.30 69.080.750 x 8.000 x 91.760
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
4T2915 1 DB|| 3 13.00 16.25 16.25 113.00 51.2630.750 x 10.000 x 58.500Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957136 1 DB|| 3 2.94 11.14 16.2231.000 x 10.000 x 38.346HD Intermediate End RH 0.750 x 2.25
1957135 1 DB|| 4 2.94 11.14 16.2241.000 x 10.000 x 54.566HD Intermediate End LH 0.750 x 2.25
TEETH 7J200 or J225 Options
935 931 General Purpose6S7341 5G1630Serial Number:
6S7291 1 WOSBBase Edge Without Holes 144.00 65.320.750 x 7.500 x 94.750
6S3237 1 IRRCorner no holes RH
6S3238 1 IRRCorner no holes LH
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 15©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 7J200 or J225 Options
935 931 Multi-Purpose5G1534 5G1679Serial Number:
5G2395 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 116.80 52.980.750 x 7.500 x 74.730
6S3237 1 IRRCorner no holes RH
6S3238 1 IRRCorner no holes LH
4T2912 1 DB|| 4 4.72 9.61 9.61 72.00 32.660.750 x 10.000 x 37.609Center 0.750
5G1523 1 SE|| 0.625 x 6.000 x 72.360Multi purpose dozer center
TEETH 8J200 or J225 Options
935 931 Multi-Purpose5G4091 5G1679Serial Number:
5G2808 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 112.00 50.800.750 x 7.500 x 72.000
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
4T2911 1 DB|| 4 7.10 10.28 10.28 88.00 39.9240.750 x 10.000 x 45.031Center 0.750 x 2.25
4T2910 2 DB|| 2 2.97 7.97 3.00 27.00 12.2520.750 x 10.000 x 13.938End 0.750 x 2.25
1957130 2 DB|| 4 2.94 7.95 10.2841.000 x 10.000 x 36.526HD Center 0.750 x 2.25
5G1523 1 SE|| 0.625 x 6.000 x 72.360Multi purpose dozer center
TEETH 8J200 or J225 Options
935 931 Multi-Purpose6S4852 6S4521Serial Number:
6S6500 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 129.60 58.790.750 x 7.500 x 84.660
6S3237 1 IRRCorner no holes RH
6S3238 1 IRRCorner no holes LH
4T2920 1 DB|| 3 6.75 12.25 12.25 73.00 33.1130.750 x 10.000 x 38.000Center 0.750 x 2.25
4T2918 2 DB|| 2 5.50 12.25 5.50 44.00 19.9620.750 x 10.000 x 23.250End 0.750 x 2.25
6S4738 DB|| 78.00 35.380.625 x 6.000 x 82.000Multi purpose dozer center
TEETH 7J200 or J225 Options
935 931 Multi-Purpose5G4085 6S4521Serial Number:
5G2809 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 127.80 57.970.750 x 7.500 x 81.875
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
4T8796 1 DB|| 3 10.69 13.75 13.75 95.90 43.5030.750 x 10.000 x 48.875Center 0.750 x 2.25
4T2914 2 DB|| 2 2.94 11.13 2.94 33.10 15.0120.750 x 10.000 x 17.000End 0.750 x 2.25
1957132 1 DB|| 3 2.94 11.13 13.7531.000 x 10.000 x 34.626HD Intermediate End RH 0.750 x 2.25
1957131 1 DB|| 4 2.94 11.13 13.7541.000 x 10.000 x 48.376HD Intermediate End LH 0.750 x 2.25
6S4738 1 DB|| 78.00 35.380.625 x 6.000 x 82.000Multi purpose dozer center
TEETH 7J200 or J225 Options
935 931 Multi-Purpose8Y5075 8Y5074Serial Number:
8Y4738 1 WOSB 30Base Edge With Segment Holes 118.10 53.570.750 x 7.500 x 76.876
5G8467 1 WOSB 14Base Edge For Bolt-on Edges or Teeth 119.90 54.390.750 x 7.500 x 76.875
5G2807 1 IRR 1Corner 1 hole RH 6.40 2.900.750 x 5.375 x 7.125
5G2806 1 IRR 1Corner 1 hole LH 6.40 2.900.750 x 5.375 x 7.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 16©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W9943 1 DB|| 4 7.81 11.00 11.00 94.90 43.0540.750 x 10.000 x 48.500Center 0.750 x 2.25
9W9944 2 DB|| 2 3.00 8.69 3.00 28.60 12.9720.750 x 10.000 x 14.688End 0.750 x 2.25
8Y5291 1 SE|| 0.625 x 6.000 x 76.610Multi purpose dozer center
TEETH 8J225 Options
6Y6362 7 DB|| 2 1.97 3.94 1.97 15.10 6.8520.750 x 10.000 x 7.874Segment 0.750 x 2.25
936 E F Corner Guard System9V1081 9C4829 9C8265 6W7781 9V1082 9C4826 9C4827 6W6002 9C6373 8R5005 9C6375 9U3185Serial Number:
6W2985 1 WOSB 28Base Edge With Segment Holes 267.70 121.431.000 x 9.600 x 103.920
8V1825 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 271.00 122.921.000 x 9.750 x 103.920
8V7619 1 WOSB 10Base Edge For Bolt-on Edges Only 286.70 130.041.000 x 9.630 x 104.906
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U0292 2 DB|| 3 7.25 14.75 14.75 122.80 55.7031.000 x 11.000 x 45.750Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3484 1 SB|| 3 7.25 14.75 14.75 105.70 47.9431.000 x 8.000 x 45.750C/IMP Center NR RH 1.000 x 2.75
9W3485 1 SB|| 3 9.00 14.75 14.75 105.70 47.9431.000 x 8.000 x 45.750C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6695 7 DB|| 2 1.38 7.69 1.38 27.40 12.4321.000 x 11.000 x 10.437Segment 1.000 x 2.75
1321037 7 DB|| 2 1.38 7.69 1.38 39.00 17.6921.375 x 11.000 x 10.438HD Segment 1.000 x 2.75
4T6695HA 7 HA|| 2 1.38 7.69 1.38 33.60 15.2421.375 x 10.875 x 10.438HA Segment (Cast) 1.000 x 2.75
9V5705 4 DB|| 11.00 4.990.750 x 8.000 x 7.000Weld-On Wear Plate
9V4484 4 DB|| 8.00 3.630.625 x 8.000 x 6.500Wear Plate for ASSY 8R5005 9C6375 9
936 E F Corner Guard System1037399 1037400 1058008 1058010Serial Number:
1052345 1 WOSB 28Base Edge With Segment Holes 256.10 116.171.000 x 9.646 x 105.551
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1073746 2 DB|| 3 7.44 15.00 15.00 125.00 56.7031.000 x 11.000 x 46.563Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1073746HARR 1 HA|| 4 7.44 15.00 15.00 192.00 87.0941.125 x 10.000 x 53.002HA Center 1.000 x 2.75
1073746HARL 1 HA|| 4 4.13 11.44 15.00 192.00 87.0941.125 x 10.000 x 53.002HA Center 1.000 x 2.75
1073298 1 SB|| 3 7.44 15.00 15.00 100.18 45.4431.000 x 8.000 x 46.563C/IMP Center NR RH 1.000 x 2.75
1073299 1 SB|| 3 9.13 15.00 15.00 100.20 45.4531.000 x 8.000 x 46.563C/IMP Center NR LH 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 17©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6695 7 DB|| 2 1.38 7.69 1.38 27.40 12.4321.000 x 11.000 x 10.437Segment 1.000 x 2.75
1321037 7 DB|| 2 1.38 7.69 1.38 39.00 17.6921.375 x 11.000 x 10.438HD Segment 1.000 x 2.75
4T6695HA 7 HA|| 2 1.38 7.69 1.38 33.60 15.2421.375 x 10.875 x 10.438HA Segment (Cast) 1.000 x 2.75
9V4484 4 DB|| 8.00 3.630.625 x 8.000 x 6.500Weld-On Wear Plate
936 E F Penetration9C4828 9V9522Serial Number:
9V9072 1 WOSBBase Edge Without Holes 279.00 126.551.000 x 9.600 x 107.520
TEETH 8J250 or J300 Options
936 E F Penetration1037401Serial Number:
1063192BASE 1 SB||Base Edge Without Holes 1.000 x 9.600 x 109.200
TEETH 8J250 or J300 Options
938 F Corner Guard System1177992Serial Number:
1104781 1 WOSB 28Base Edge With Segment Holes 241.00 109.321.000 x 9.637 x 95.940
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1104782 2 DB|| 3 6.75 13.81 13.81 120.00 54.4331.000 x 11.000 x 41.750Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
9V4484 4 DB|| 8.00 3.630.625 x 8.000 x 6.500Weld-On Wear Plate
938 F G Corner Guard System1037399 1037400 1058008 1058010 1243468 1243469 1243470 1243471 1438957 1497443 1587479 1487480 MORESerial Number:
1052345 1 WOSB 28Base Edge With Segment Holes 256.10 116.171.000 x 9.646 x 105.551
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1073746 2 DB|| 3 7.44 15.00 15.00 125.00 56.7031.000 x 11.000 x 46.563Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1386425 2 DB|| 3 7.44 15.00 15.00 168.50 76.4331.375 x 11.000 x 46.563HD Center 1.000 x 2.75
1386560 2 DB|| 2 5.56 2.44 27.70 12.5621.375 x 13.563 x 6.250HD End 1.000 x 2.75
1073746HARR 1 HA|| 4 7.44 15.00 15.00 192.00 87.0941.125 x 10.000 x 53.002HA Center 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 18©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1073746HARL 1 HA|| 4 4.13 11.44 15.00 192.00 87.0941.125 x 10.000 x 53.002HA Center 1.000 x 2.75
1073298 1 SB|| 3 7.44 15.00 15.00 100.18 45.4431.000 x 8.000 x 46.563C/IMP Center NR RH 1.000 x 2.75
1073299 1 SB|| 3 9.13 15.00 15.00 100.20 45.4531.000 x 8.000 x 46.563C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6695 7 DB|| 2 1.38 7.69 1.38 27.40 12.4321.000 x 11.000 x 10.437Segment 1.000 x 2.75
1321037 7 DB|| 2 1.38 7.69 1.38 39.00 17.6921.375 x 11.000 x 10.438HD Segment 1.000 x 2.75
4T6695HA 7 HA|| 2 1.38 7.69 1.38 33.60 15.2421.375 x 10.875 x 10.438HA Segment (Cast) 1.000 x 2.75
9V4484 4 DB|| 8.00 3.630.625 x 8.000 x 6.500Weld-On Wear Plate
938 F G Corner Guard System1129405 1105701 1105702 1105703Serial Number:
1104712 1 WOSB 28Base Edge With Segment Holes 268.00 121.561.000 x 9.620 x 107.310
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1104711 2 DB|| 3 9.13 15.31 15.31 126.90 57.5621.000 x 11.000 x 47.250Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1239195 1 SB|| 3 9.13 15.31 15.31 109.20 49.5321.000 x 8.000 x 47.250C/IMP Center NR RH 1.000 x 2.75
1239196 1 SB|| 3 7.50 15.31 15.31 109.20 49.5321.000 x 8.000 x 47.250C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6695 7 DB|| 2 1.38 7.69 1.38 27.40 12.4321.000 x 11.000 x 10.437Segment 1.000 x 2.75
1321037 7 DB|| 2 1.38 7.69 1.38 39.00 17.6921.375 x 11.000 x 10.438HD Segment 1.000 x 2.75
4T6695HA 7 HA|| 2 1.38 7.69 1.38 33.60 15.2421.375 x 10.875 x 10.438HA Segment (Cast) 1.000 x 2.75
9V4484 4 DB|| 8.00 3.630.625 x 8.000 x 6.500Weld-On Wear Plate
938 F G Penetration1037401Serial Number:
1063192BASE 1 SB||Base Edge Without Holes 1.000 x 9.600 x 109.200
TEETH 8J250 or J300 Options
939 Corner Guard System8Y8263Serial Number:
8Y8763 1 WOSB 28Base Edge With Segment Holes 213.00 96.621.000 x 9.625 x 85.000
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1006359 2 DB|| 3 5.96 12.09 12.09 94.00 42.6431.000 x 11.000 x 36.100Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 19©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J250 or J300 Options
4T6692 7 DB|| 2 1.38 4.94 1.38 20.00 9.0721.000 x 11.000 x 7.688Segment 1.000 x 2.75
4T6692HA 7 HA|| 2 1.38 4.94 1.38 24.70 11.2021.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 2.75
939 Multi-Purpose8Y8261Serial Number:
8Y8763 1 WOSB 28Base Edge With Segment Holes 213.00 96.621.000 x 9.625 x 85.000
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1006359 2 DB|| 3 5.96 12.09 12.09 94.00 42.6431.000 x 11.000 x 36.100Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
1062327 1 DB|| 14Multi purpose dozer center x 2
TEETH 8J250 or J300 Options
4T6692 7 DB|| 2 1.38 4.94 1.38 20.00 9.0721.000 x 11.000 x 7.688Segment 1.000 x 2.75
4T6692HA 7 HA|| 2 1.38 4.94 1.38 24.70 11.2021.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 2.75
941 Corner Guard System5V4651Serial Number:
6W2977 1 WOSB 28Base Edge With Segment Holes 204.40 92.711.000 x 9.625 x 79.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0605 2 DB|| 3 5.50 11.25 11.25 88.70 40.2331.000 x 11.000 x 33.500Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6691 7 DB|| 2 1.38 4.13 1.38 17.70 8.0321.000 x 11.000 x 6.875Segment 1.000 x 2.75
941 General Purpose8K7935 1V5026Serial Number:
8K6452 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 192.00 87.091.000 x 9.000 x 81.750
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1467 2 DB|| 4 4.88 10.00 10.00 107.00 48.5341.000 x 11.000 x 40.750Center 1.000 x 2.75
TEETH 8J250 or J300 Options
941 Flush Mounted Teeth9K8467 1V9858Serial Number:
9K8471 1 WOSBBase Edge Without Holes 192.00 87.091.000 x 9.625 x 93.500
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
TEETH 7J250 Options
941 Corner Guard SystemCGSSerial Number:
9V6572 1 WOSB 28Base Edge With Segment Holes 241.80 109.681.000 x 9.650 x 93.310
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 20©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
5V4670 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 244.70 110.991.000 x 9.625 x 93.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0295 2 DB|| 3 6.50 13.25 13.25 108.20 49.0831.000 x 11.000 x 40.375Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3486 1 SB|| 3 7.38 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR RH 1.000 x 2.75
9W3487 1 SB|| 3 6.50 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
941 Multi-Purpose5V4648 5V4649Serial Number:
6W2977 1 WOSB 28Base Edge With Segment Holes 204.40 92.711.000 x 9.625 x 79.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0605 2 DB|| 3 5.50 11.25 11.25 88.70 40.2331.000 x 11.000 x 33.500Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
4T8073 1 DB|| 13 2.88 6.00 6.00 99.60 45.18130.625 x 8.000 x 77.750Multi purpose dozer center 0.625 x 2
TEETH 8J250 or J300 Options
4T6691 7 DB|| 2 1.38 4.13 1.38 17.70 8.0321.000 x 11.000 x 6.875Segment 1.000 x 2.75
941 Multi-Purpose9K3752 9K3753Serial Number:
8K6452 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 192.00 87.091.000 x 9.000 x 81.750
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1467 2 DB|| 4 4.88 10.00 10.00 107.00 48.5341.000 x 11.000 x 40.750Center 1.000 x 2.75
4T8073 1 DB|| 13 2.88 6.00 6.00 99.60 45.18130.625 x 8.000 x 77.750Multi purpose dozer center 0.625 x 2
TEETH 8J250 or J300 Options
941 Side Dump7K5281Serial Number:
7K6108 1 WOSBBase Edge Without Holes 107.00 48.530.750 x 8.000 x 94.000
4K6103 1 IRRCorner no holes RH
4K6104 1 IRRCorner no holes LH
943 Corner Guard System4V8280 9V9030Serial Number:
9V6571 1 WOSB 28Base Edge With Segment Holes 217.00 98.431.000 x 9.620 x 81.890
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 21©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4V8335 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 213.80 96.981.000 x 9.625 x 81.890
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0294 2 DB|| 3 5.69 11.63 100.00 45.3631.000 x 11.000 x 34.625Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6691 7 DB|| 2 1.38 4.13 1.38 17.70 8.0321.000 x 11.000 x 6.875Segment 1.000 x 2.75
943 Flush Mounted Teeth9V5114 6W3557Serial Number:
9V5110 1 WOSBBase Edge Without Holes
TEETH 8J250 Options
943 Corner Guard System9V8999 8Y3830 4V8695Serial Number:
9V6570 1 WOSB 28Base Edge With Segment Holes 209.00 94.801.000 x 9.625 x 86.813
4V8850 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 226.90 102.921.000 x 9.625 x 86.813
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0293 2 DB|| 3 6.06 12.44 12.44 106.00 48.0831.000 x 11.000 x 37.000Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6692 7 DB|| 2 1.38 4.94 1.38 20.00 9.0721.000 x 11.000 x 7.688Segment 1.000 x 2.75
4T6692HA 7 HA|| 2 1.38 4.94 1.38 24.70 11.2021.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 2.75
943 Flush Mounted Teeth9V5133 8Y3831 6W3553Serial Number:
1V9077 1 WOSBBase Edge Without Holes 206.00 93.441.000 x 9.000 x 90.000
TEETH 8J250 Options
943 Multi-Purpose2V7193 2V7274Serial Number:
9V6571 1 WOSB 28Base Edge With Segment Holes 217.00 98.431.000 x 9.620 x 81.890
4V8335 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 213.80 96.981.000 x 9.625 x 81.890
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0294 2 DB|| 3 5.69 11.63 100.00 45.3631.000 x 11.000 x 34.625Center 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 22©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
4T8079 1 DB|| 13 4.56 6.00 6.00 104.00 47.17130.625 x 8.000 x 81.125Multi purpose dozer center 0.625 x 2
TEETH 8J250 or J300 Options
4T6691 7 DB|| 2 1.38 4.13 1.38 17.70 8.0321.000 x 11.000 x 6.875Segment 1.000 x 2.75
943 Multi-Purpose8V7359 8V7363Serial Number:
6W2976 1 WOSB 28Base Edge With Segment Holes 227.50 103.191.000 x 9.625 x 88.500
8V7453 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 207.00 93.891.000 x 9.620 x 88.500
4T9563 2 WOSB 3 6.13 12.44 12.44 102.30 46.4031.000 x 11.000 x 38.125Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
4T8072 1 DB|| 10 2.94 6.00 6.00 76.70 34.79100.625 x 8.000 x 59.875Multi purpose dozer center 0.625 x 2
4T8082 2 DB|| 3 2.88 4.00 4.00 17.50 7.9430.625 x 8.000 x 13.750Multi purpose dozer end 0.625 x 2
TEETH 8J250 or J300 Options
4T6692 5 DB|| 2 1.38 4.94 1.38 20.00 9.0721.000 x 11.000 x 7.688Center Segment 1.000 x 2.75
4T6693 2 DB|| 2 1.38 5.50 1.38 21.30 9.6621.000 x 11.000 x 8.250End Segment 1.000 x 2.75
4T6692HA 5 HA|| 2 1.38 4.94 1.38 24.70 11.2021.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 2.75
4T6693HA 2 HA|| 2 1.38 5.50 1.38 25.90 11.7521.375 x 10.875 x 8.250HA Segment (Cast) 1.000 x 2.75
944 Corner Guard System5V7265Serial Number:
6W2986 1 WOSB 30Base Edge With Segment Holes 244.40 110.861.000 x 9.600 x 95.000
5V7277 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 247.40 112.221.000 x 9.600 x 95.000
5V7396FAB 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.500 x 8.000
5V7395FAB 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.500 x 8.000
8E5303 1 IRR 2Corner 2 hole LH 23.60 10.702.000 x 8.219 x 8.966
8E5302 1 IRR 2Corner 2 hole RH 23.60 10.702.000 x 8.219 x 8.966
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U2414 2 DB|| 3 6.81 13.75 13.75 170.20 77.2031.182 x 14.170 x 41.125Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321030 2 DB|| 3 6.81 13.75 13.75 197.00 89.3631.375 x 14.250 x 41.125HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
TEETH 8J300 Options
4T6694 5 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Center Segment 1.000 x 3
4T6693 2 DB|| 2 1.38 5.50 1.38 21.30 9.6621.000 x 11.000 x 8.250End Segment 1.000 x 3
1321035 5 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Center Segment 1.000 x 3
1321036 2 DB|| 2 1.38 5.50 1.38 32.00 14.5121.375 x 11.000 x 8.250HD End Segment 1.000 x 3
4T6694HA 5 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 3
4T6693HA 2 HA|| 2 1.38 5.50 1.38 25.90 11.7521.375 x 10.875 x 8.250HA Segment (Cast) 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
944 General Purpose8K9039 9K8655Serial Number:
8K8161 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 225.00 102.061.000 x 9.000 x 96.000
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 23©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1U1465 1 DB|| 3 4.88 10.63 10.63 82.80 37.5631.000 x 11.000 x 31.000Center 1.000 x 2.75
1U1464 2 DB|| 3 5.50 10.63 10.63 86.20 39.1031.000 x 11.000 x 32.250End 1.000 x 2.75
1321026 1 DB|| 3 4.88 10.63 10.63 114.00 51.7131.375 x 11.000 x 31.000HD Center 1.000 x 2.75
1321027 2 DB|| 3 5.50 10.63 10.63 119.00 53.9831.375 x 11.000 x 32.250HD End 1.000 x 2.75
9W3469 1 SB|| 3 4.88 10.63 10.63 65.00 29.4831.000 x 8.000 x 31.000C/IMP Center NR 1.000 x 2.75
9W3470 1 SB|| 3 5.50 10.63 10.63 68.00 30.8431.000 x 8.000 x 32.250C/IMP End NR RH 1.000 x 2.75
9W3471 1 SB|| 3 5.50 10.63 10.63 68.00 30.8431.000 x 8.000 x 32.250C/IMP End NR LH 1.000 x 2.75
8J9078 1 HA|| 3 4.88 10.63 10.63 60.30 27.3530.875 x 8.000 x 31.000HA Center 1.000 x 2.75
8J9077 2 HA|| 3 5.50 10.63 10.63 62.70 28.4430.875 x 8.000 x 32.250HA End 1.000 x 2.75
TEETH 8J300 Options
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
944 Corner Guard System5V7267 5V7269 5V7271Serial Number:
6W2987 1 WOSB 30Base Edge With Segment Holes 265.40 120.381.000 x 9.600 x 102.920
5V7276 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 268.50 121.791.000 x 9.600 x 102.920
5V7396FAB 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.500 x 8.000
5V7395FAB 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.500 x 8.000
8E5303 1 IRR 2Corner 2 hole LH 23.60 10.702.000 x 8.219 x 8.966
8E5302 1 IRR 2Corner 2 hole RH 23.60 10.702.000 x 8.219 x 8.966
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U2412 2 DB|| 3 7.19 14.56 14.56 186.90 84.7831.180 x 14.170 x 45.188Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321031 2 DB|| 3 7.19 14.56 14.56 216.00 97.9831.375 x 14.250 x 45.188HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
9W3490 1 SB|| 3 7.19 14.56 14.563C/IMP Center NR RH 1.000 x 3
9W3491 1 SB|| 3 8.88 14.56 14.563C/IMP Center NR LH 1.000 x 3
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR RH 1.000 x 3
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR LH 1.000 x 3
TEETH 8J300 Options
4T6694 5 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Center Segment 1.000 x 3
4T6695 2 DB|| 2 1.38 7.69 1.38 27.40 12.4321.000 x 11.000 x 10.437End Segment 1.000 x 3
1321035 5 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Center Segment 1.000 x 3
1321037 2 DB|| 2 1.38 7.69 1.38 39.00 17.6921.375 x 11.000 x 10.438HD End Segment 1.000 x 3
4T6694HA 5 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 3
4T6695HA 2 HA|| 2 1.38 7.69 1.38 33.60 15.2421.375 x 10.875 x 10.438HA Segment (Cast) 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
944 General Purpose8K9041 8K9042 8K9043 9K8658 9K8657 9K8656Serial Number:
8K8162 1 WOSB 20Base Edge For Bolt-on Edges or Teeth 257.90 116.981.000 x 9.000 x 105.875
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1470 1 DB|| 4 3.94 10.38 10.38 160.50 72.8041.180 x 14.170 x 39.000Center 1.000 x 2.75
1U1469 2 DB|| 3 6.25 10.38 10.38 135.00 61.2331.180 x 14.170 x 33.250End 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 24©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1321028 1 DB|| 4 3.94 10.38 10.38 186.00 84.3741.375 x 14.250 x 39.000HD Center 1.000 x 2.75
1321029 2 DB|| 3 6.25 10.38 10.38 159.00 72.1231.375 x 14.250 x 33.250HD End 1.000 x 2.75
9W3466 1 SB|| 4 3.94 10.38 10.38 115.00 52.1641.125 x 10.000 x 39.000C/IMP Center NR 1.000 x 2.75
9W3467 1 SB|| 3 6.25 10.38 10.38 98.00 44.4531.125 x 10.000 x 33.250C/IMP End NR RH 1.000 x 2.75
9W3468 1 SB|| 3 6.25 10.38 10.38 98.00 44.4531.125 x 10.000 x 33.250C/IMP End NR LH 1.000 x 2.75
8J9076 1 HA|| 4 3.94 10.38 10.38 67.00 30.3940.875 x 8.000 x 39.000HA Center 1.000 x 2.75
8J9075 2 HA|| 3 6.25 10.38 10.38 57.00 25.8530.875 x 8.000 x 33.250HA End 1.000 x 2.75
TEETH 10J300 Options
944 Flush Mounted Teeth9K8728 9K8733 9K8734 9K8735 9K8930Serial Number:
1V3915 1 WOSBBase Edge Without Holes 239.80 108.771.000 x 9.000 x 105.250
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
TEETH 8J300 Options
950 Corner Guard System5V7265Serial Number:
6W2986 1 WOSB 30Base Edge With Segment Holes 244.40 110.861.000 x 9.600 x 95.000
5V7277 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 247.40 112.221.000 x 9.600 x 95.000
5V7396FAB 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.500 x 8.000
5V7395FAB 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.500 x 8.000
8E5303 1 IRR 2Corner 2 hole LH 23.60 10.702.000 x 8.219 x 8.966
8E5302 1 IRR 2Corner 2 hole RH 23.60 10.702.000 x 8.219 x 8.966
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U2414 2 DB|| 3 6.81 13.75 13.75 170.20 77.2031.182 x 14.170 x 41.125Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321030 2 DB|| 3 6.81 13.75 13.75 197.00 89.3631.375 x 14.250 x 41.125HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
TEETH 8J300 Options
4T6694 5 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Center Segment 1.000 x 3
4T6693 2 DB|| 2 1.38 5.50 1.38 21.30 9.6621.000 x 11.000 x 8.250End Segment 1.000 x 3
1321035 5 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Center Segment 1.000 x 3
1321036 2 DB|| 2 1.38 5.50 1.38 32.00 14.5121.375 x 11.000 x 8.250HD End Segment 1.000 x 3
4T6694HA 5 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 3
4T6693HA 2 HA|| 2 1.38 5.50 1.38 25.90 11.7521.375 x 10.875 x 8.250HA Segment (Cast) 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 General Purpose8K9039 9K8655Serial Number:
8K8161 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 225.00 102.061.000 x 9.000 x 96.000
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1465 1 DB|| 3 4.88 10.63 10.63 82.80 37.5631.000 x 11.000 x 31.000Center 1.000 x 2.75
1U1464 2 DB|| 3 5.50 10.63 10.63 86.20 39.1031.000 x 11.000 x 32.250End 1.000 x 2.75
1321026 1 DB|| 3 4.88 10.63 10.63 114.00 51.7131.375 x 11.000 x 31.000HD Center 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 25©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1321027 2 DB|| 3 5.50 10.63 10.63 119.00 53.9831.375 x 11.000 x 32.250HD End 1.000 x 2.75
9W3469 1 SB|| 3 4.88 10.63 10.63 65.00 29.4831.000 x 8.000 x 31.000C/IMP Center NR 1.000 x 2.75
9W3470 1 SB|| 3 5.50 10.63 10.63 68.00 30.8431.000 x 8.000 x 32.250C/IMP End NR RH 1.000 x 2.75
9W3471 1 SB|| 3 5.50 10.63 10.63 68.00 30.8431.000 x 8.000 x 32.250C/IMP End NR LH 1.000 x 2.75
8J9078 1 HA|| 3 4.88 10.63 10.63 60.30 27.3530.875 x 8.000 x 31.000HA Center 1.000 x 2.75
8J9077 2 HA|| 3 5.50 10.63 10.63 62.70 28.4430.875 x 8.000 x 32.250HA End 1.000 x 2.75
TEETH 8J300 Options
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 Corner Guard System5V7267 5V7269 5V7271Serial Number:
6W2987 1 WOSB 30Base Edge With Segment Holes 265.40 120.381.000 x 9.600 x 102.920
5V7276 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 268.50 121.791.000 x 9.600 x 102.920
5V7396FAB 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.500 x 8.000
5V7395FAB 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.500 x 8.000
8E5303 1 IRR 2Corner 2 hole LH 23.60 10.702.000 x 8.219 x 8.966
8E5302 1 IRR 2Corner 2 hole RH 23.60 10.702.000 x 8.219 x 8.966
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U2412 2 DB|| 3 7.19 14.56 14.56 186.90 84.7831.180 x 14.170 x 45.188Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321031 2 DB|| 3 7.19 14.56 14.56 216.00 97.9831.375 x 14.250 x 45.188HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
9W3490 1 SB|| 3 7.19 14.56 14.563C/IMP Center NR RH 1.000 x 3
9W3491 1 SB|| 3 8.88 14.56 14.563C/IMP Center NR LH 1.000 x 3
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR RH 1.000 x 3
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR LH 1.000 x 3
TEETH 8J300 Options
4T6694 5 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Center Segment 1.000 x 3
4T6695 2 DB|| 2 1.38 7.69 1.38 27.40 12.4321.000 x 11.000 x 10.437End Segment 1.000 x 3
1321035 5 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Center Segment 1.000 x 3
1321037 2 DB|| 2 1.38 7.69 1.38 39.00 17.6921.375 x 11.000 x 10.438HD End Segment 1.000 x 3
4T6694HA 5 HA|| 2 1.44 6.13 1.44 28.80 13.061.375 x 10.875 x 9.000HA Segment (Cast) 1.000
4T6695HA 2 HA|| 2 1.38 7.69 1.38 33.60 15.241.375 x 10.875 x 10.438HA Segment (Cast) 1.000
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 General Purpose8K9041 8K9042 8K9043 9K8658 9K8657 9K8656Serial Number:
8K8162 1 WOSB 20Base Edge For Bolt-on Edges or Teeth 257.90 116.981.000 x 9.000 x 105.875
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1470 1 DB|| 4 3.94 10.38 10.38 160.50 72.8041.180 x 14.170 x 39.000Center 1.000 x 2.75
1U1469 2 DB|| 3 6.25 10.38 10.38 135.00 61.2331.180 x 14.170 x 33.250End 1.000 x 2.75
1321028 1 DB|| 4 3.94 10.38 10.38 186.00 84.3741.375 x 14.250 x 39.000HD Center 1.000 x 2.75
1321029 2 DB|| 3 6.25 10.38 10.38 159.00 72.1231.375 x 14.250 x 33.250HD End 1.000 x 2.75
9W3466 1 SB|| 4 3.94 10.38 10.38 115.00 52.1641.125 x 10.000 x 39.000C/IMP Center NR 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 26©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W3467 1 SB|| 3 6.25 10.38 10.38 98.00 44.4531.125 x 10.000 x 33.250C/IMP End NR RH 1.000 x 2.75
9W3468 1 SB|| 3 6.25 10.38 10.38 98.00 44.4531.125 x 10.000 x 33.250C/IMP End NR LH 1.000 x 2.75
8J9076 1 HA|| 4 3.94 10.38 10.38 67.00 30.3940.875 x 8.000 x 39.000HA Center 1.000 x 2.75
8J9075 2 HA|| 3 6.25 10.38 10.38 57.00 25.8530.875 x 8.000 x 33.250HA End 1.000 x 2.75
TEETH 10J300 Options
950 Flush Mounted Teeth9K8728 9K8733 9K8734 9K8735 9K8930Serial Number:
1V3915 1 WOSBBase Edge Without Holes 239.80 108.771.000 x 9.000 x 105.250
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
TEETH 8J300 Options
950 B E Corner Guard System5V7352 9V3298Serial Number:
5V7410 1 WOSB 12Base Edge For Bolt-on Edges Only 287.90 130.591.000 x 9.625 x 108.000
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U0601 2 DB|| 3 7.52 15.28 15.28 197.10 89.4031.180 x 14.170 x 47.650Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321034 2 DB|| 3 7.53 15.28 15.28 243.30 110.3631.375 x 14.250 x 47.650HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
1U0601HAN 3 HA|| 2 7.50 15.25 116.20 52.7121.625 x 10.375 x 30.250HA Center (Cast) 1.000 x 3
4T8101HA 2 HA|| 3 3.25 2.69 2.69 48.60 22.0431.625 x 15.125 x 8.375HA End (Cast) 1.000 x 3
9W3492 1 SB|| 3 7.50 15.25 15.25 153.00 69.4031.125 x 11.000 x 47.500C/IMP Center NR RH 1.000 x 3
9W3493 1 SB|| 3 9.50 15.25 15.25 153.00 69.4031.125 x 11.000 x 47.500C/IMP Center NR LH 1.000 x 3
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR RH 1.000 x 3
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR LH 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 B E F FII Corner Guard System9C8345 9C8357 5V4447 6V3299 6W7787 6W6004 8R8616 8R6170 8R6171 8R8615 4E4773 1093635 1093636 1093637Serial Number:
9V6573 1 WOSB 30Base Edge With Segment Holes 386.10 175.131.250 x 11.130 x 107.740
5V4696 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 391.80 177.721.250 x 11.125 x 107.750
5V1783 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.000 x 8.500
5V1784 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.000 x 8.500
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U0601 2 DB|| 3 7.52 15.28 15.28 197.10 89.4031.180 x 14.170 x 47.650Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321034 2 DB|| 3 7.53 15.28 15.28 243.30 110.3631.375 x 14.250 x 47.650HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
1U0601HAN 3 HA|| 2 7.50 15.25 116.20 52.7121.625 x 10.375 x 30.250HA Center (Cast) 1.000 x 3
4T8101HA 2 HA|| 3 3.25 2.69 2.69 48.60 22.0431.625 x 15.125 x 8.375HA End (Cast) 1.000 x 3
9W3492 1 SB|| 3 7.50 15.25 15.25 153.00 69.4031.125 x 11.000 x 47.500C/IMP Center NR RH 1.000 x 3
9W3493 1 SB|| 3 9.50 15.25 15.25 153.00 69.4031.125 x 11.000 x 47.500C/IMP Center NR LH 1.000 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 27©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR RH 1.000 x 3
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR LH 1.000 x 3
TEETH 8J300 Options
4T6695 7 DB|| 2 1.38 7.69 1.38 27.40 12.431.000 x 11.000 x 10.437Segment 1.000 x 3
1321037 7 DB|| 2 1.38 7.69 1.38 39.00 17.691.375 x 11.000 x 10.438HD Segment 1.000 x 3
4T6695HA 7 HA|| 2 1.38 7.69 1.38 33.60 15.2421.375 x 10.875 x 10.438HA Segment (Cast) 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 G GII H Corner Guard System, Material Handling1419393 1419394 1419395 1419396 1419397 1419398 1419399 1487243 1473672 1473677 2096667 2151280Serial Number:
1414847 1 WOSB 30Base Edge With Segment Holes 402.20 182.431.250 x 11.130 x 113.620
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1399230 2 DB|| 3 8.00 16.31 16.31 209.00 94.8031.180 x 14.170 x 50.500Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1359666 2 DB|| 3 8.00 16.31 16.31 260.70 118.2531.375 x 14.250 x 50.500HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
1399230HAN 3 HA|| 2 7.92 16.31 129.50 58.7421.625 x 10.375 x 32.153HA Center (Cast) 1.000 x 3
4T8101HA 2 HA|| 3 3.25 2.69 2.69 48.60 22.0431.625 x 15.125 x 8.375HA End (Cast) 1.000 x 3
1380672 1 SB|| 3 8.00 16.31 16.31 163.00 73.9431.125 x 11.000 x 50.500C/IMP Center NR RH 1.000 x 3
1380673 1 SB|| 3 9.88 16.31 16.31 163.00 73.9431.125 x 11.000 x 50.500C/IMP Center NR LH 1.000 x 3
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR RH 1.000 x 3
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR LH 1.000 x 3
TEETH 8J300 Options
1324715 7 DB|| 2 1.38 8.19 1.38 46.70 21.1821.375 x 12.000 x 10.938Segment 1.000 x 3
1407601 7 DB|| 2 1.66 8.19 46.90 21.2721.180 x 14.170 x 11.500Wider Segment 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 H Corner Guard System, Material Handling1570314 1570316 1570317 2192694Serial Number:
1289590 1 SB|| 30Base Edge With Segment Holes 393.90 178.671.250 x 11.102 x 111.565
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1073381 2 DB|| 3 7.75 15.63 15.63 202.20 91.721.180 x 14.170 x 48.875Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321049 2 DB|| 3 7.75 15.63 15.631.375 x 14.170 x 48.875HD Center 1.000
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.181.375 x 19.625 x 6.688HD End 1.000
1380676 1 SB|| 3 7.75 15.63 15.631.125 x 11.000 x 48.875C/IMP Center NR LH 1.000
1380677 1 SB|| 3 7.75 15.63 15.631.125 x 11.000 x 48.875C/IMP Center NR RH 1.000
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.251.125 x 14.313 x 7.063C/IMP End NR RH 1.000
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.251.125 x 14.313 x 7.063C/IMP End NR LH 1.000
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 28©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J300 Options
1324715 7 DB|| 2 1.38 8.19 1.38 46.70 21.181.375 x 12.000 x 10.938Segment 1.000 x 3
1407601 7 DB|| 2 1.66 8.19 46.90 21.2721.180 x 14.170 x 11.500Wider Segment 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 B E F Penetration6W4600 8R8617Serial Number:
6W4598 1 SB||Base Edge Without Holes 1.000 x 11.100 x 111.220
TEETH 8J300 Options
950 Multi-Purpose5V7273 5V7272Serial Number:
6W2988 1 WOSB 30Base Edge With Segment Holes 268.40 121.741.000 x 9.600 x 104.000
5V7396FAB 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.500 x 8.000
5V7395FAB 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.500 x 8.000
8E5302 1 IRR 2Corner 2 hole RH 23.60 10.702.000 x 8.219 x 8.966
8E5303 1 IRR 2Corner 2 hole LH 23.60 10.702.000 x 8.219 x 8.966
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U2413 2 DB|| 3 7.25 14.75 14.75 189.20 85.8231.180 x 14.170 x 45.750Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321032 2 DB|| 3 7.25 14.75 14.75 219.00 99.3431.375 x 14.250 x 45.750HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
4T8068 1 DB|| 12 3.00 6.00 6.00 92.20 41.82120.625 x 8.000 x 72.000Multi purpose dozer center 0.625 x 2
4T8078 2 DB|| 4 3.50 3.00 3.00 20.30 9.2140.625 x 8.000 x 16.000Multi purpose dozer end 0.625 x 2
TEETH 8J300 Options
4T6694 5 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Center Segment 1.000 x 3
4T6695 2 DB|| 2 1.38 7.69 1.38 27.40 12.4321.000 x 11.000 x 10.437End Segment 1.000 x 3
1321035 5 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Center Segment 1.000 x 3
1321037 2 DB|| 2 1.38 7.69 1.38 39.00 17.6921.375 x 11.000 x 10.438HD End Segment 1.000 x 3
4T6694HA 5 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 3
4T6695HA 2 HA|| 2 1.38 7.69 1.38 33.60 15.2421.375 x 10.875 x 10.438HA Segment (Cast) 1.000 x 3
950 Multi-Purpose2V3160 1V9785Serial Number:
8K8162 1 WOSB 20Base Edge For Bolt-on Edges or Teeth 257.90 116.981.000 x 9.000 x 105.875
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1470 1 DB|| 4 3.94 10.38 10.38 160.50 72.8041.180 x 14.170 x 39.000Center 1.000 x 2.75
1U1469 2 DB|| 3 6.25 10.38 10.38 135.00 61.2331.180 x 14.170 x 33.250End 1.000 x 2.75
1321028 1 DB|| 4 3.94 10.38 10.38 186.00 84.3741.375 x 14.250 x 39.000HD Center 1.000 x 2.75
1321029 2 DB|| 3 6.25 10.38 10.38 159.00 72.1231.375 x 14.250 x 33.250HD End 1.000 x 2.75
9W3466 1 SB|| 4 3.94 10.38 10.38 115.00 52.1641.125 x 10.000 x 39.000C/IMP Center NR 1.000 x 2.75
9W3467 1 SB|| 3 6.25 10.38 10.38 98.00 44.4531.125 x 10.000 x 33.250C/IMP End NR RH 1.000 x 2.75
9W3468 1 SB|| 3 6.25 10.38 10.38 98.00 44.4531.125 x 10.000 x 33.250C/IMP End NR LH 1.000 x 2.75
8J9076 1 HA|| 4 3.94 10.38 10.38 67.00 30.3940.875 x 8.000 x 39.000HA Center 1.000 x 2.75
8J9075 2 HA|| 3 6.25 10.38 10.38 57.00 25.8530.875 x 8.000 x 33.250HA End 1.000 x 2.75
4T8068 1 DB|| 12 3.00 6.00 6.00 92.20 41.82120.625 x 8.000 x 72.000Multi purpose dozer center 0.625 x 2
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 29©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T8078 2 DB|| 4 3.50 3.00 3.00 20.30 9.2140.625 x 8.000 x 16.000Multi purpose dozer end 0.625 x 2
TEETH 10J300 Options
950 Side Dump9K6491Serial Number:
5V7416 1 WOSBBase Edge Without Holes 317.00 143.791.000 x 9.688 x 121.688
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
950 B E F Spade Nose Rock6W1136 8R8618Serial Number:
6W2973 1 SB\_/ 18Spade Nose Base Edge 597.10 270.841.375 x 19.410 x 110.830
6W3468 2 IRRCorner no holes LH/RH 13.90 6.301.250 x 6.375 x 8.750
7T5962 1 DB|| 4 2.88 4.94 5.25 83.80 38.0141.180 x 14.170 x 20.875Center 1.250 x 3.25
7T5963 1 DB\\ 4 3.56 5.75 9.94 100.80 45.7241.180 x 14.170 x 28.438Center RH 1.250 x 3.25
7T5960 1 DB\\ 4 4.50 4.94 5.75 84.80 38.4641.180 x 14.170 x 24.625End RH 1.250 x 3.25
7T5961 1 DB// 4 3.56 5.75 9.94 100.80 45.7241.180 x 14.170 x 28.438Center LH 1.250 x 3.25
7T5964 1 DB// 4 4.50 4.94 5.75 84.80 38.4641.180 x 14.170 x 24.625End RH 1.250 x 3.25
TEETH 8J350 Options
4T3015 1 DB|| 2 2.44 5.25 40.50 18.3721.180 x 14.170 x 10.125Segment 1.250 x 3.25
4T9123 3 DB\\ 2 4.13 5.75 4.13 41.80 18.9621.180 x 14.170 x 14.000Segment RH 1.250 x 3.25
4T9124 3 DB// 2 4.13 5.75 4.13 41.80 18.9621.180 x 14.170 x 14.000Segment LH 1.250 x 3.25
1321038 1 DB|| 2 2.44 5.25 48.00 21.7721.375 x 14.250 x 10.125HD Segment 1.250 x 3.25
1321039 3 DB\\ 2 4.13 5.75 50.00 22.6821.375 x 14.250 x 14.000HD Segment RH 1.250 x 3.25
1321040 3 DB// 2 4.13 5.75 4.13 50.00 22.6821.375 x 14.250 x 14.000HD Segment LH 1.250 x 3.25
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 B E F Spade Nose Rock6W1137 8R8919Serial Number:
9C0967 1 SB\_/Spade Nose Base Edge Without Holes 586.00 265.811.375 x 19.375 x 110.813
6W3468 2 IRRCorner no holes LH/RH 13.90 6.301.250 x 6.375 x 8.750
TEETH 8J350 Options
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 G H Spade Nose Rock1419401Serial Number:
1429406 1 SB\_/Spade Nose Base Edge Without Holes 1.375 x 19.400 x 116.890
6W3468 2 IRRCorner no holes LH/RH 13.90 6.301.250 x 6.375 x 8.750
TEETH 8J350 Options
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
950 G H Spade Nose Rock1419400Serial Number:
1418823 1 SB\_/ 18Spade Nose Base Edge 1.375 x 19.400 x 116.890
6W3468 2 IRRCorner no holes LH/RH 13.90 6.301.250 x 6.375 x 8.750
1321089 1 DB|| 4Center 1.250 x 3.25
7T5963 1 DB\\ 4 3.56 5.75 9.94 100.80 45.7241.180 x 14.170 x 28.438Center RH 1.250 x 3.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 30©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1099017 1 DB\\ 4End RH 1.250 x 3.25
7T5961 1 DB// 4 3.56 5.75 9.94 100.80 45.7241.180 x 14.170 x 28.438Center LH 1.250 x 3.25
1099016 1 DB// 4End LH 1.250 x 3.25
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
951 Corner Guard System5V4669 5V4664Serial Number:
6W2977 1 WOSB 28Base Edge With Segment Holes 204.40 92.711.000 x 9.625 x 79.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0605 2 DB|| 3 5.50 11.25 11.25 88.70 40.2331.000 x 11.000 x 33.500Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6691 7 DB|| 2 1.38 4.13 1.38 17.70 8.0321.000 x 11.000 x 6.875Segment 1.000 x 2.75
951 General Purpose8K6453 9K2754 2V2916 4V0387Serial Number:
8K6452 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 192.00 87.091.000 x 9.000 x 81.750
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1467 2 DB|| 4 4.88 10.00 10.00 107.00 48.5341.000 x 11.000 x 40.750Center 1.000 x 2.75
TEETH 8J250 or J300 Options
951 Flush Mounted Teeth9K8465 1V9900 2V5032Serial Number:
9K8471 1 WOSBBase Edge Without Holes 192.00 87.091.000 x 9.625 x 93.500
TEETH 8J250 Options
951 Corner Guard System5V4671 2V7166Serial Number:
9V6572 1 WOSB 28Base Edge With Segment Holes 241.80 109.681.000 x 9.650 x 93.310
5V4670 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 244.70 110.991.000 x 9.625 x 93.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0295 2 DB|| 3 6.50 13.25 13.25 108.20 49.0831.000 x 11.000 x 40.375Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3486 1 SB|| 3 7.38 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR RH 1.000 x 2.75
9W3487 1 SB|| 3 6.50 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 31©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J250 or J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
951 Multi-Purpose5V4665 5V4666Serial Number:
6W2977 1 WOSB 28Base Edge With Segment Holes 204.40 92.711.000 x 9.625 x 79.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0605 2 DB|| 3 5.50 11.25 11.25 88.70 40.2331.000 x 11.000 x 33.500Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
4T8073 1 DB|| 13 2.88 6.00 6.00 99.60 45.18130.625 x 8.000 x 77.750Multi purpose dozer center 0.625 x 2
TEETH 8J250 or J300 Options
4T6691 7 DB|| 2 1.38 4.13 1.38 17.70 8.0321.000 x 11.000 x 6.875Segment 1.000 x 2.75
951 Multi-Purpose9K3846 9K3847Serial Number:
8K6452 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 192.00 87.091.000 x 9.000 x 81.750
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1467 2 DB|| 4 4.88 10.00 10.00 107.00 48.5341.000 x 11.000 x 40.750Center 1.000 x 2.75
4T8073 1 DB|| 13 2.88 6.00 6.00 99.60 45.18130.625 x 8.000 x 77.750Multi purpose dozer center 0.625 x 2
TEETH 8J250 or J300 Options
953 Corner Guard System5V0624 6W0183Serial Number:
9V6570 1 WOSB 28Base Edge With Segment Holes 209.00 94.801.000 x 9.625 x 86.813
4V8850 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 226.90 102.921.000 x 9.625 x 86.813
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0293 2 DB|| 3 6.06 12.44 12.44 106.00 48.0831.000 x 11.000 x 37.000Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6692 7 DB|| 2 1.38 4.94 1.38 20.00 9.0721.000 x 11.000 x 7.688Segment 1.000 x 2.75
4T6692HA 7 HA|| 2 1.38 4.94 1.38 24.70 11.2021.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 2.75
953 Flush Mounted Teeth9V5144 6W3555Serial Number:
1V9077 1 WOSBBase Edge Without Holes 206.00 93.441.000 x 9.000 x 90.000
TEETH 8J250 Options
953 B C Corner Guard System6W0184 4V5310 8Y3832 9Y9100Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 32©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9V6572 1 WOSB 28Base Edge With Segment Holes 241.80 109.681.000 x 9.650 x 93.310
5V4670 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 244.70 110.991.000 x 9.625 x 93.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0295 2 DB|| 3 6.50 13.25 13.25 108.20 49.0831.000 x 11.000 x 40.375Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3486 1 SB|| 3 7.38 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR RH 1.000 x 2.75
9W3487 1 SB|| 3 6.50 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
TEETH 8J250 or J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
953 B C Flush Mounted Teeth9V5157 6W3551 8Y3833 8Y9101Serial Number:
1V3916 1 WOSBBase Edge Without Holes 231.40 104.961.000 x 9.000 x 96.000
TEETH 8J250 or J300 Options
953 Multi-Purpose3V6081 3V6114Serial Number:
9V6570 1 WOSB 28Base Edge With Segment Holes 209.00 94.801.000 x 9.625 x 86.813
4V8850 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 226.90 102.921.000 x 9.625 x 86.813
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0293 2 DB|| 3 6.06 12.44 12.44 106.00 48.0831.000 x 11.000 x 37.000Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
4T8080 1 DB|| 14 4.15 6.00 6.00 110.60 50.17140.625 x 8.000 x 86.300Multi purpose dozer center 0.625 x 2
TEETH 8J250 or J300 Options
4T6692 7 DB|| 2 1.38 4.94 1.38 20.00 9.0721.000 x 11.000 x 7.688Segment 1.000 x 2.75
4T6692HA 7 HA|| 2 1.38 4.94 1.38 24.70 11.2021.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 2.75
953 B C Multi-Purpose8V7366 8V7365 8Y9583 8Y9582Serial Number:
9V6572 1 WOSB 28Base Edge With Segment Holes 241.80 109.681.000 x 9.650 x 93.310
5V4670 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 244.70 110.991.000 x 9.625 x 93.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 33©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0295 2 DB|| 3 6.50 13.25 13.25 108.20 49.0831.000 x 11.000 x 40.375Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3486 1 SB|| 3 7.38 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR RH 1.000 x 2.75
9W3487 1 SB|| 3 6.50 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
4T8083 1 DB|| 11 2.44 6.00 6.00 83.10 37.69110.625 x 8.000 x 64.875Multi purpose dozer center 0.625 x 2
4T8082 2 DB|| 3 2.88 4.00 4.00 17.50 7.9430.625 x 8.000 x 13.750Multi purpose dozer end 0.625 x 2
1U0257 6 ADP 2J250 Bolt-On Center Adapter 22.70 10.304.135 x 3.248 x 14.267
6I9251 1 ADP 2J250 Corner Adapter RH 2 holes 34.30 15.561.500 x 10.574 x 13.329
6I9250 1 ADP 2J250 Corner Adapter LH 2 holes 34.30 15.561.500 x 10.574 x 13.337
TEETH 8J250 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
955 General Purpose8K7864 8K7865 9K1063Serial Number:
5V7437 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 236.00 107.051.000 x 9.750 x 88.500
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1471 2 DB|| 4 7.13 10.63 10.63 182.10 82.6041.180 x 14.170 x 44.125Center 1.000 x 2.75
TEETH 8J300 Options
955 Flush Mounted Teeth9K8462 8K8464 9K8468Serial Number:
9K8461 1 WOSBBase Edge Without Holes 1.000 x 9.000 x 88.500
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
TEETH 7J300 Options
955 Corner Guard SystemCGSSerial Number:
6W2978 1 WOSB 30Base Edge With Segment Holes 314.20 142.521.250 x 11.000 x 89.000
5V1783 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.000 x 8.500
5V1784 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.000 x 8.500
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U2410 2 DB|| 3 6.25 12.63 12.63 153.00 69.4031.180 x 14.170 x 37.750Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
TEETH 8J300 Options
4T6692 7 DB|| 2 1.38 4.94 1.38 20.00 9.0731.000 x 11.000 x 7.688Segment 1.000 x 3
4T6692HA 7 HA|| 2 1.38 4.94 1.38 24.70 11.2031.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 3
955 General Purpose1V2912 1V9079Serial Number:
1V2911 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 211.00 95.711.000 x 9.000 x 90.000
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 34©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
1U1473 2 DB|| 4 6.50 11.00 11.00 190.00 86.1841.180 x 14.170 x 44.875Center 1.000 x 2.75
TEETH 8J300 Options
955 Flush Mounted Teeth1V9080 1V9081Serial Number:
1V9077 1 WOSBBase Edge Without Holes 206.00 93.441.000 x 9.000 x 90.000
4V8667 1 IRRCorner 1 hole RH 10.90 4.941.000 x 6.375 x 10.000
4V8668 1 IRRCorner 1 hole LH 10.90 4.941.000 x 6.375 x 10.000
TEETH 8J300 Options
955 Corner Guard System5V7258Serial Number:
5V7263 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 343.60 155.851.250 x 11.000 x 95.813
5V1783 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.000 x 8.500
5V1784 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.000 x 8.500
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U2411 2 DB|| 3 6.88 13.94 13.94 169.00 76.6631.180 x 14.170 x 41.625Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
TEETH 8J300 Options
955 Flush Mounted Teeth2V7293Serial Number:
2V7298 1 WOSBBase Edge Without Holes 1.250 x 11.000 x 95.813
8K6455 1 IRRCorner no holes RH 18.50 8.391.500 x 8.000 x 8.500
8K6456 1 IRRCorner no holes LH 18.50 8.391.500 x 8.000 x 8.500
TEETH 9J300 Options
955 Multi-Purpose5V7260 5V7259Serial Number:
6W2978 1 WOSB 30Base Edge With Segment Holes 314.20 142.521.250 x 11.000 x 89.000
5V1783 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.000 x 8.500
5V1784 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.000 x 8.500
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U2410 2 DB|| 3 6.25 12.63 12.63 153.00 69.4031.180 x 14.170 x 37.750Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
4T8074 1 DB|| 14 4.00 6.00 6.00 110.20 49.99140.625 x 8.000 x 86.000Multi purpose dozer center 0.625 x 2.25
TEETH 8J300 Options
4T6692 7 DB|| 2 1.38 4.94 1.38 20.00 9.0731.000 x 11.000 x 7.688Segment 1.000 x 3
4T6692HA 7 HA|| 2 1.38 4.94 1.38 24.70 11.2031.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 3
955 Multi-Purpose9K8623 9K8817Serial Number:
9K0658 1 WOSBBase Edge Without Holes 1.250 x 11.000 x 91.100
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 35©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
4T8074 1 DB|| 14 4.00 6.00 6.00 110.20 49.99140.625 x 8.000 x 86.000Multi purpose dozer center 0.625 x 2
TEETH 8J300 Options
960 F Corner Guard System, Material Handling1093637 1093640 1093639Serial Number:
9V6573 1 WOSB 30Base Edge With Segment Holes 386.10 175.131.250 x 11.130 x 107.740
5V4696 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 391.80 177.721.250 x 11.125 x 107.750
5V1783 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.000 x 8.500
5V1784 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.000 x 8.500
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U0601 2 DB|| 3 7.52 15.28 15.28 197.10 89.4031.180 x 14.170 x 47.650Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321034 2 DB|| 3 7.53 15.28 15.28 243.30 110.3631.375 x 14.250 x 47.650HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
1U0601HAN 3 HA|| 2 7.50 15.25 116.20 52.7121.625 x 10.375 x 30.250HA Center (Cast) 1.000 x 3
4T8101HA 2 HA|| 3 3.25 2.69 2.69 48.60 22.0431.625 x 15.125 x 8.375HA End (Cast) 1.000 x 3
9W3492 1 SB|| 3 7.50 15.25 15.25 153.00 69.4031.125 x 11.000 x 47.500C/IMP Center NR RH 1.000 x 3
9W3493 1 SB|| 3 9.50 15.25 15.25 153.00 69.4031.125 x 11.000 x 47.500C/IMP Center NR LH 1.000 x 3
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR RH 1.000 x 3
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR LH 1.000 x 3
TEETH 8J300 Options
4T6695 7 DB|| 2 1.38 7.69 1.38 27.40 12.4321.000 x 11.000 x 10.437Segment 1.000 x 3
1321037 7 DB|| 2 1.38 7.69 1.38 39.00 17.6921.375 x 11.000 x 10.438HD Segment 1.000 x 3
4T6695HA 7 HA|| 2 1.38 7.69 1.38 33.60 15.2421.375 x 10.875 x 10.438HA Segment (Cast) 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
960 F Corner Guard System, Material Handling7I3106 1052956 1070582Serial Number:
9V6575 1 WOSB 30Base Edge With Segment Holes 534.00 242.221.500 x 11.811 x 119.750
7V1490 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 541.10 245.441.500 x 11.811 x 119.375
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U0593 2 DB|| 3 8.31 16.88 16.88 213.70 96.9331.180 x 14.170 x 51.875Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1004046 2 DB|| 3 8.25 16.88 16.88 305.30 138.4831.375 x 16.000 x 51.875Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 36©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1U0593HA 3 HA|| 4 8.31 16.88 211.20 95.8021.750 x 15.625 x 33.500HA Center (Cast) 1.250 x 4.1252 8.31 16.88 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
1U0593TP 3 DB|| 4 8.31 16.88 60.10 27.2621.000 x 12.586 x 33.500Bolt on Top Plate Center 1.250 x 52 8.31 16.88 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1U0593HAN 3 HA|| 2 8.31 16.88 163.10 73.981.750 x 11.125 x 33.500Narrow HA Center (Cast) 1.250 x 4.125
2085345 2 DB|| 3 9.88 16.88 16.88 237.00 107.5031.180 x 14.170 x 51.875C/IMP Center REV 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
9W3477 1 SB|| 3 9.81 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR RH 1.250 x 4.125
9W3478 1 SB|| 3 8.31 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
TEETH 8J350 or J450 Options
4T6699 7 DB|| 2 1.75 7.13 42.70 19.3721.180 x 14.170 x 10.625Segment 1.250 x 4.125
1406868 7 DB|| 2 1.75 7.13 1.75 49.80 22.5921.375 x 14.170 x 10.625HD Segment 1.250 x 4.125
1744114 7 HA|| 2 1.75 7.13 54.70 24.8131.750 x 13.500 x 10.625HA Segment (Cast) 1.250 x 4.125
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
960 F Spade Nose Rock8R8618Serial Number:
6W2973 1 SB\_/ 18Spade Nose Base Edge 597.10 270.841.375 x 19.410 x 110.830
6W3468 2 IRRCorner no holes LH/RH 13.90 6.301.250 x 6.375 x 8.750
7T5962 1 DB|| 4 2.88 4.94 5.25 83.80 38.0141.180 x 14.170 x 20.875Center 1.250 x 3.25
7T5963 1 DB\\ 4 3.56 5.75 9.94 100.80 45.7241.180 x 14.170 x 28.438Center RH 1.250 x 3.25
7T5960 1 DB\\ 4 4.50 4.94 5.75 84.80 38.4641.180 x 14.170 x 24.625End RH 1.250 x 3.25
7T5961 1 DB// 4 3.56 5.75 9.94 100.80 45.7241.180 x 14.170 x 28.438Center LH 1.250 x 3.25
7T5964 1 DB// 4 4.50 4.94 5.75 84.80 38.4641.180 x 14.170 x 24.625End RH 1.250 x 3.25
TEETH 8J350 Options
4T3015 1 DB|| 2 2.44 5.25 40.50 18.3721.180 x 14.170 x 10.125Segment 1.250 x 3.25
4T9123 3 DB\\ 2 4.13 5.75 4.13 41.80 18.9621.180 x 14.170 x 14.000Segment RH 1.250 x 3.25
4T9124 3 DB// 2 4.13 5.75 4.13 41.80 18.9621.180 x 14.170 x 14.000Segment LH 1.250 x 3.25
1321038 1 DB|| 2 2.44 5.25 48.00 21.7721.375 x 14.250 x 10.125HD Segment 1.250 x 3.25
1321039 3 DB\\ 2 4.13 5.75 50.00 22.6821.375 x 14.250 x 14.000HD Segment RH 1.250 x 3.25
1321040 3 DB// 2 4.13 5.75 4.13 50.00 22.6821.375 x 14.250 x 14.000HD Segment LH 1.250 x 3.25
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
960 F Spade Nose Rock8R8619Serial Number:
9C0967 1 SB\_/Spade Nose Base Edge Without Holes 586.00 265.811.375 x 19.375 x 110.813
6W3468 2 IRRCorner no holes LH/RH 13.90 6.301.250 x 6.375 x 8.750
TEETH 8J350 Options
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
962 G GII Corner Guard System, Material Handling1419393 1473678 1487243 1496170 2096667 2151280 1419398 1473672 1418094 1392553 1393511 2028846Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 37©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1414847 1 WOSB 30Base Edge With Segment Holes 402.20 182.431.250 x 11.130 x 113.620
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1399230 2 DB|| 3 8.00 16.31 16.31 209.00 94.8031.180 x 14.170 x 50.500Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1359666 2 DB|| 3 8.00 16.31 16.31 260.70 118.2531.375 x 14.250 x 50.500HD Center 1.000 x 3
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.1831.375 x 19.625 x 6.688HD End 1.000 x 3
1399230HAN 3 HA|| 2 7.92 16.31 129.50 58.7421.625 x 10.375 x 32.153HA Center (Cast) 1.000 x 3
4T8101HA 2 HA|| 3 3.25 2.69 2.69 48.60 22.0431.625 x 15.125 x 8.375HA End (Cast) 1.000 x 3
1380672 1 SB|| 3 8.00 16.31 16.31 163.00 73.9431.125 x 11.000 x 50.500C/IMP Center NR RH 1.000 x 3
1380673 1 SB|| 3 9.88 16.31 16.31 163.00 73.9431.125 x 11.000 x 50.500C/IMP Center NR LH 1.000 x 3
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR RH 1.000 x 3
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.2531.125 x 14.313 x 7.063C/IMP End NR LH 1.000 x 3
TEETH 8J300 Options
1324715 7 DB|| 2 1.38 8.19 1.38 46.70 21.1821.375 x 12.000 x 10.938Segment 1.000 x 3
1407601 7 DB|| 2 1.66 8.19 46.90 21.2721.180 x 14.170 x 11.500Wider Segment 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
962 G GII H Corner Guard System, Material Handling, Coal1572610 1570316 1570317 1570318Serial Number:
1289590 1 SB|| 30Base Edge With Segment Holes 393.90 178.671.250 x 11.102 x 111.565
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1073381 2 DB|| 3 7.75 15.63 15.63 202.20 91.721.180 x 14.170 x 48.875Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
1321049 2 DB|| 3 7.75 15.63 15.631.375 x 14.170 x 48.875HD Center 1.000
1321033 2 DB|| 3 7.13 2.69 2.69 46.70 21.181.375 x 19.625 x 6.688HD End 1.000
1380676 1 SB|| 3 7.75 15.63 15.631.125 x 11.000 x 48.875C/IMP Center NR LH 1.000
1380677 1 SB|| 3 7.75 15.63 15.631.125 x 11.000 x 48.875C/IMP Center NR RH 1.000
9W3488 1 SB|| 3 1.94 2.69 2.69 27.00 12.251.125 x 14.313 x 7.063C/IMP End NR RH 1.000
9W3489 1 SB|| 3 1.94 2.69 2.69 27.00 12.251.125 x 14.313 x 7.063C/IMP End NR LH 1.000
TEETH 8J300 Options
1324715 7 DB|| 2 1.38 8.19 1.38 46.70 21.181.375 x 12.000 x 10.938Segment 1.000 x 3
1407601 7 DB|| 2 1.66 8.19 46.90 21.2721.180 x 14.170 x 11.500Wider Segment 1.000 x 3
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
962 H Penetration2627400 2627414 2627415 2627416Serial Number:
1064619 1 SB||Base Edge Without Holes
1408824 1 SE||Weld-On Bucket Wear Plate
1U1304 8 ADPJ300 Weld-On Center Adapter 21.16 9.60
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 38©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH J300 Options
962 H Penetration2765193Serial Number:
2039976 1 SB||Base Edge Without Holes
962 GII Waste Handling1473672Serial Number:
9V6572 1 WOSB 28Base Edge With Segment Holes 241.80 109.681.000 x 9.650 x 93.310
5V4670 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 244.70 110.991.000 x 9.625 x 93.500
4V1544 1 IRR 1Corner 1 hole RH 12.10 5.491.000 x 8.270 x 8.150
4V1545 1 IRR 1Corner 1 hole LH 12.10 5.491.000 x 8.270 x 8.150
6I8310 1 IRR 2Corner 2 hole RH 20.00 9.071.500 x 8.641 x 8.125
6I8311 1 IRR 2Corner 2 hole LH 20.00 9.071.500 x 8.641 x 8.125
2530060 1 IRR 2New Style 2 Hole Corner Protector RH 20.50 9.300.875 x 8.313 x 12.250
2530061 1 IRR 2New Style 2 Hole Corner Protector LH 20.50 9.300.875 x 8.313 x 12.250
1U0295 2 DB|| 3 6.50 13.25 13.25 108.20 49.0831.000 x 11.000 x 40.375Center 1.000 x 2.75
4T8091 2 DB|| 2 5.56 2.44 20.60 9.3421.000 x 13.563 x 6.250End 1.000 x 2.75
9W3486 1 SB|| 3 7.38 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR RH 1.000 x 2.75
9W3487 1 SB|| 3 6.50 13.25 13.25 93.10 42.2331.000 x 8.000 x 40.375C/IMP Center NR LH 1.000 x 2.75
9W3481 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR RH 1.000 x 2.75
9W3482 1 SB|| 2 2.50 2.44 19.50 8.8521.000 x 10.563 x 6.250C/IMP End NR LH 1.000 x 2.75
4T8083 1 DB|| 11 2.44 6.00 6.00 83.10 37.69110.625 x 8.000 x 64.875Multi purpose dozer center 0.625 x 2
4T8082 2 DB|| 3 2.88 4.00 4.00 17.50 7.9430.625 x 8.000 x 13.750Multi purpose dozer end 0.625 x 2
TEETH 8J250 or J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3921.000 x 11.000 x 8.860Segment 1.000 x 2.75
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9721.375 x 11.000 x 8.860HD Segment 1.000 x 2.75
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 2.75
962 G H Spade Nose Rock1487245 1392551Serial Number:
1418823 1 SB\_/ 18Spade Nose Base Edge 1.375 x 19.400 x 116.890
6W3468 2 IRRCorner no holes LH/RH 13.90 6.301.250 x 6.375 x 8.750
1321089 1 DB|| 4Center 1.250 x 3.25
7T5963 1 DB\\ 4 3.56 5.75 9.94 100.80 45.7241.180 x 14.170 x 28.438Center RH 1.250 x 3.25
1099017 1 DB\\ 4End RH 1.250 x 3.25
7T5961 1 DB// 4 3.56 5.75 9.94 100.80 45.7241.180 x 14.170 x 28.438Center LH 1.250 x 3.25
1099016 1 DB// 4End LH 1.250 x 3.25
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
962 G H Spade Nose Rock1487247Serial Number:
1429406 1 SB\_/Spade Nose Base Edge Without Holes 1.375 x 19.400 x 116.890
6W3468 2 IRRCorner no holes LH/RH 13.90 6.301.250 x 6.375 x 8.750
TEETH 8J350 Options
9W6747 2 DB|| 4 1.38 18.00 42.20 19.1421.000 x 10.000 x 20.750Rear Wear Plate 0.750 x 2.252 1.38 18.00 ...2nd Row0.750 x 2.25
963 Corner Guard System4V6519Serial Number:
6W2979 1 WOSB 30Base Edge With Segment Holes 316.20 143.431.250 x 11.000 x 89.563
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 39©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4V4958 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 316.60 143.611.250 x 11.000 x 89.563
5V1783 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.000 x 8.500
5V1784 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.000 x 8.500
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U0599 2 DB|| 3 6.89 12.69 12.69 156.00 70.7631.180 x 14.170 x 38.445Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
TEETH 8J300 Options
4T6692 5 DB|| 2 1.38 4.94 1.38 20.00 9.0721.000 x 11.000 x 7.688Center Segment 1.000 x 3
4T6693 2 DB|| 2 1.38 5.50 1.38 21.30 9.6621.000 x 11.000 x 8.250End Segment 1.000 x 3
4T6692HA 5 HA|| 2 1.38 4.94 1.38 24.70 11.2021.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 3
4T6693HA 2 HA|| 2 1.38 5.50 1.38 25.90 11.7521.375 x 10.875 x 8.250HA Segment (Cast) 1.000 x 3
9W6748 2 DB|_| 4 1.44 18.25 41.70 18.9121.000 x 10.000 x 21.125Rear Wear Plate 0.750 x 2.252 1.44 18.25 ...2nd Row0.750 x 2.25
963 Flush Mounted Teeth9V5295Serial Number:
9V5340 1 WOSBBase Edge Without Holes 318.40 144.421.250 x 10.500 x 92.375
4V8667 1 IRRCorner 1 hole RH 10.90 4.941.000 x 6.375 x 10.000
4V8668 1 IRRCorner 1 hole LH 10.90 4.941.000 x 6.375 x 10.000
TEETH 8J300 Options
9W6748 2 DB|_| 4 1.44 18.25 41.70 18.9121.000 x 10.000 x 21.125Rear Wear Plate 0.750 x 2.252 1.44 18.25 ...2nd Row0.750 x 2.25
963 Corner Guard SystemCGSSerial Number:
6W2980 1 WOSB 30Base Edge With Segment Holes 345.10 156.531.250 x 11.000 x 97.500
4V3174 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 349.70 158.621.250 x 11.000 x 97.500
5V1783 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.000 x 8.500
5V1784 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.000 x 8.500
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U0600 2 DB|| 3 6.81 13.81 13.81 175.60 79.6521.180 x 14.170 x 42.500Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
TEETH 8J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3931.000 x 11.000 x 8.860Segment 1.000 x 3
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9731.375 x 11.000 x 8.860HD Segment 1.000 x 3
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 3
9W6748 2 DB|_| 4 1.44 18.25 41.70 18.9121.000 x 10.000 x 21.125Rear Wear Plate 0.750 x 2.252 1.44 18.25 ...2nd Row0.750 x 2.25
963 Flush Mounted Teeth9V5298Serial Number:
9V5328 1 WOSBBase Edge Without Holes 355.00 161.031.250 x 10.500 x 100.500
4V8667 1 IRRCorner 1 hole RH 10.90 4.941.000 x 6.375 x 10.000
4V8668 1 IRRCorner 1 hole LH 10.90 4.941.000 x 6.375 x 10.000
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 40©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J300 Options
9W6748 2 DB|_| 4 1.44 18.25 41.70 18.9121.000 x 10.000 x 21.125Rear Wear Plate 0.750 x 2.252 1.44 18.25 ...2nd Row0.750 x 2.25
963 B C Corner Guard System8Y9110Serial Number:
8Y6263 1 WOSB 30Base Edge With Segment Holes 330.00 149.691.250 x 11.125 x 98.375
5V2773 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.938 x 9.844
5V2772 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.938 x 9.844
8E5320 1 IRR 2Corner 2 hole RH
8E5321 1 IRR 2Corner 2 hole LH
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
8E5793 2 DB|| 3 7.00 14.25 14.25 181.10 82.1531.250 x 14.250 x 41.750Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 8J350 Options
4T6697 5 DB|| 2 1.75 4.75 1.75 32.80 14.8821.180 x 14.170 x 8.250Center Segment 1.250 x 4.125
4T6696 2 DB|| 2 2.00 3.50 2.00 29.60 13.4321.180 x 14.170 x 7.500End Segment 1.250 x 4.125
1406865 5 DB|| 2 2.00 3.50 2.0021.375 x 14.170 x 7.500HD Center Segment 1.250 x 4.125
1406866 2 DB|| 2 1.75 4.75 1.7521.375 x 14.170 x 8.250HD End Segment 1.250 x 4.125
9W6748 2 DB|_| 4 1.44 18.25 41.70 18.9121.000 x 10.000 x 21.125Rear Wear Plate 0.750 x 2.252 1.44 18.25 ...2nd Row0.750 x 2.25
963 B Flush Mounted Teeth8Y9409Serial Number:
8Y9404 1 WOSBBase Edge Without Holes 1.250 x 11.100 x 101.700
6W2453 1 IRRCorner no holes RH
6W2454 1 IRRCorner no holes LH
TEETH 8J350 Options
9W6748 2 DB|_| 4 1.44 18.25 41.70 18.9121.000 x 10.000 x 21.125Rear Wear Plate 0.750 x 2.252 1.44 18.25 ...2nd Row0.750 x 2.25
963 Multi-Purpose3V8704 3V8710Serial Number:
6W2979 1 WOSB 30Base Edge With Segment Holes 316.20 143.431.250 x 11.000 x 89.563
4V4958 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 316.60 143.611.250 x 11.000 x 89.563
5V1783 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.000 x 8.500
5V1784 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.000 x 8.500
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U0599 2 DB|| 3 6.89 12.69 12.69 156.00 70.7631.180 x 14.170 x 38.445Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
4T8081 1 DB|| 14 5.50 6.00 6.00 112.00 50.80140.625 x 8.000 x 89.000Multi purpose dozer center 0.625 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 41©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J300 Options
4T6692 5 DB|| 2 1.38 4.94 1.38 20.00 9.0721.000 x 11.000 x 7.688Center Segment 1.000 x 3
4T6693 2 DB|| 2 1.38 5.50 1.38 21.30 9.6621.000 x 11.000 x 8.250End Segment 1.000 x 3
4T6692HA 5 HA|| 2 1.38 4.94 1.38 24.70 11.2021.375 x 10.875 x 7.688HA Segment (Cast) 1.000 x 3
4T6693HA 2 HA|| 2 1.38 5.50 1.38 25.90 11.7521.375 x 10.875 x 8.250HA Segment (Cast) 1.000 x 3
963 B C Multi-Purpose8V7367 8V7364 8Y9626 8Y9625Serial Number:
6W2980 1 WOSB 30Base Edge With Segment Holes 345.10 156.531.250 x 11.000 x 97.500
4V3174 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 349.70 158.621.250 x 11.000 x 97.500
5V1783 1 IRR 1Corner 1 hole RH 11.40 5.171.000 x 8.000 x 8.500
5V1784 1 IRR 1Corner 1 hole LH 11.40 5.171.000 x 8.000 x 8.500
8E5300 1 IRR 2Corner 2 hole RH 22.30 10.122.000 x 7.996 x 9.276
8E5301 1 IRR 2Corner 2 hole LH 22.30 10.122.000 x 7.996 x 9.276
2530062 1 IRR 2New Style 2 Hole Corner Protector RH 28.10 12.751.125 x 8.188 x 13.375
2530063 1 IRR 2New Style 2 Hole Corner Protector LH 28.10 12.751.125 x 8.188 x 13.375
1U0600 2 DB|| 3 6.81 13.81 13.81 175.60 79.6521.180 x 14.170 x 42.500Center 1.000 x 3
4T8101 2 DB|| 3 7.13 2.69 2.69 41.00 18.6031.250 x 19.625 x 6.688End 1.000 x 3
4T8084 1 DB|| 11 3.25 6.00 6.00 85.20 38.65110.625 x 8.000 x 66.500Center 0.625 x 2.25
4T8085 2 DB|| 3 3.50 4.00 4.00 19.20 8.7130.625 x 8.000 x 15.000End 0.625 x 2.25
4T4307 6 ADP 2J300 Bolt-On Center Adapter 32.60 14.794.691 x 4.249 x 15.196
8E5309 1 ADP 2J300 Corner Adapter RH 2 holes 44.50 20.182.000 x 10.519 x 14.066
8E5308 1 ADP 2J300 Corner Adapter LH 2 holes 44.50 20.182.000 x 10.519 x 14.066
TEETH 8J300 Options
4T6694 7 DB|| 2 1.38 6.10 1.38 22.90 10.3931.000 x 11.000 x 8.860Segment 1.000 x 3
1321035 7 DB|| 2 1.38 6.10 1.38 33.00 14.9731.375 x 11.000 x 8.860HD Segment 1.000 x 3
4T6694HA 7 HA|| 2 1.44 6.13 1.44 28.80 13.0621.375 x 10.875 x 9.000HA Segment (Cast) 1.000 x 3
966 C Corner Guard System5V7340 5V7341 5V7342Serial Number:
6W2990 1 WOSB 30Base Edge With Segment Holes 395.00 179.171.250 x 11.000 x 112.500
5V2772 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.938 x 9.844
5V2773 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.938 x 9.844
8E5320 1 IRR 2Corner 2 hole RH
8E5321 1 IRR 2Corner 2 hole LH
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U2406 2 DB|| 3 8.88 15.88 15.88 199.50 90.4931.180 x 14.170 x 48.375Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1004045 2 DB|| 3 8.88 15.88 15.88 284.50 129.0531.375 x 16.000 x 48.375Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
9W3479 1 SB|| 3 7.75 15.88 15.88 205.60 93.2631.375 x 11.000 x 48.500C/IMP Center NR RH 1.250 x 4.125
9W3480 1 SB|| 3 9.00 15.88 15.88 205.60 93.2631.375 x 11.000 x 48.500C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 42©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J350 Options
4T6698 7 DB|| 2 2.00 5.50 2.00 37.80 17.1521.180 x 14.170 x 9.500Segment 1.250 x 4.125
1406867 7 DB|| 2 2.00 5.50 44.90 20.3721.375 x 14.170 x 9.500HD Segment 1.250 x 4.125
4T6698FHA 7 HA|| 2 2.00 5.50 35.10 15.9221.250 x 10.500 x 9.500HA Segment (Fabricated) 1.250 x 4.125
9V6106 2 DB||Weld-On Wear Plate
966 C General Purpose9K0286 9K0287 9K1611Serial Number:
8K9754 1 WOSB 24Base Edge For Bolt-on Edges or Teeth 407.60 184.881.250 x 10.500 x 115.000
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
1U1476 1 DB|| 8 4.63 3.25 11.00 226.00 102.5181.180 x 14.170 x 55.250Center 1.000 x 3
1U1475 2 DB|| 4 6.13 3.25 11.00 122.00 55.3441.180 x 14.170 x 29.750End 1.000 x 3
9W3472 1 SB|| 8 4.63 3.25 11.00 199.30 90.4081.125 x 11.000 x 55.250C/IMP Center NR LH/RH 1.000 x 3
9W3473 1 SB|| 4 6.13 3.25 11.00 109.70 49.7641.125 x 11.000 x 29.750C/IMP End NR RH 1.000 x 3
9W3474 1 SB|| 4 6.13 3.25 11.00 109.70 49.7641.125 x 11.000 x 29.750C/IMP End NR LH 1.000 x 3
TEETH 8J300 Options
9V6106 2 DB||Weld-On Wear Plate
966 C Flush Mounted Teeth9K8736Serial Number:
1V3917 1 WOSBBase Edge Without Holes 415.30 188.381.250 x 10.500 x 115.000
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
TEETH 7J300 or J350 Options
9V6106 2 DB||Weld-On Wear Plate
966 C Flush Mounted Teeth2V3704Serial Number:
1V3917 1 WOSBBase Edge Without Holes 415.30 188.381.250 x 10.500 x 115.000
1V8664 2 IRRCorner no holes LH/RH 15.90 7.211.250 x 7.000 x 9.500
TEETH 7J300 or J350 Options
9V6106 2 DB||Weld-On Wear Plate
966 D E Corner Guard System7V6825 9V0970Serial Number:
7I3631 1 WOSB 30Base Edge With Segment Holes 514.30 233.281.500 x 11.800 x 115.160
7V6844 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 520.90 236.281.500 x 11.811 x 115.000
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U1909 2 DB|| 3 9.25 16.25 16.25 205.20 93.0831.180 x 14.170 x 49.750Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1359533 2 DB|| 3 9.25 16.25 16.25 292.70 132.7731.375 x 16.000 x 49.750Heavy Duty Wider Center 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 43©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1073282 1 SB|| 3 9.25 16.25 16.2531.250 x 11.000 x 49.750C/IMP Center NR RH 1.250 x 4.125
1073283 1 SB|| 3 7.75 16.25 16.2531.250 x 11.000 x 49.750C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 8J350 or J450 Options
1006664 7 DB|| 2 1.81 6.42 1.81 40.20 18.231.180 x 14.170 x 10.039Segment 1.250
1406869 7 DB|| 2 1.81 6.42 47.60 21.591.375 x 14.173 x 10.039HD Segment 1.250
9W6749 2 DB|| 4 1.38 19.50 69.70 31.6221.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
966 D E F Corner Guard System6W7793 8R8209 8R6172 9C8299 2Q2801 8R8204 8R8205 9C8299 9C8309 7V1474 9V0161 6W7794 7V1784 9V0965Serial Number:
9V6575 1 WOSB 30Base Edge With Segment Holes 534.00 242.221.500 x 11.811 x 119.750
7V1490 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 541.10 245.441.500 x 11.811 x 119.375
7V0912 1 WOSB 12Base Edge For Bolt-on Edges Only 445.40 202.031.250 x 11.000 x 119.688
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U0593 2 DB|| 3 8.31 16.88 16.88 213.70 96.9331.180 x 14.170 x 51.875Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1004046 2 DB|| 3 8.25 16.88 16.88 305.30 138.4831.375 x 16.000 x 51.875Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1U0593HA 3 HA|| 4 8.31 16.88 211.20 95.8021.750 x 15.625 x 33.500HA Center (Cast) 1.250 x 4.1252 8.31 16.88 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
1U0593TP 3 DB|| 4 8.31 16.88 60.10 27.2621.000 x 12.586 x 33.500Bolt on Top Plate Center 1.250 x 52 8.31 16.88 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1U0593HAN 3 HA|| 2 8.31 16.88 163.10 73.981.750 x 11.125 x 33.500Narrow HA Center (Cast) 1.250 x 4.125
2085345 2 DB|| 3 9.88 16.88 16.88 237.00 107.5031.180 x 14.170 x 51.875C/IMP Center REV 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
9W3477 1 SB|| 3 9.81 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR RH 1.250 x 4.125
9W3478 1 SB|| 3 8.31 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
TEETH 8J350 or J450 Options
4T6699 7 DB|| 2 1.75 7.13 42.70 19.3721.180 x 14.170 x 10.625Segment 1.250 x 4.125
1406868 7 DB|| 2 1.75 7.13 1.75 49.80 22.5921.375 x 14.170 x 10.625HD Segment 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 44©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1744114 7 HA|| 2 1.75 7.13 54.70 24.8131.750 x 13.500 x 10.625HA Segment (Cast) 1.250 x 4.125
9W6749 2 DB|| 4 1.38 19.50 69.70 31.6221.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
966 G GII H Corner Guard System, Material Handling1331679 1331677 1331676 1331681 1469627 1469626Serial Number:
9V6575 1 WOSB 30Base Edge With Segment Holes 534.00 242.221.500 x 11.811 x 119.750
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U0593 2 DB|| 3 8.31 16.88 16.88 213.70 96.9331.180 x 14.170 x 51.875Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1004046 2 DB|| 3 8.25 16.88 16.88 305.30 138.4831.375 x 16.000 x 51.875Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1U0593HA 3 HA|| 4 8.31 16.88 211.20 95.8021.750 x 15.625 x 33.500HA Center (Cast) 1.250 x 4.1252 8.31 16.88 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
1U0593TP 3 DB|| 4 8.31 16.88 60.10 27.2621.000 x 12.586 x 33.500Bolt on Top Plate Center 1.250 x 52 8.31 16.88 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1U0593HAN 3 HA|| 2 8.31 16.88 163.10 73.981.750 x 11.125 x 33.500Narrow HA Center (Cast) 1.250 x 4.125
2085345 2 DB|| 3 9.88 16.88 16.88 237.00 107.5031.180 x 14.170 x 51.875C/IMP Center REV 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
9W3477 1 SB|| 3 9.81 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR RH 1.250 x 4.125
9W3478 1 SB|| 3 8.31 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
TEETH 8J350 or J450 Options
4T6699 7 DB|| 2 1.75 7.13 42.70 19.3721.180 x 14.170 x 10.625Segment 1.250 x 4.125
1406868 7 DB|| 2 1.75 7.13 1.75 49.80 22.5921.375 x 14.170 x 10.625HD Segment 1.250 x 4.125
1744114 7 HA|| 2 1.75 7.13 54.70 24.8121.750 x 13.500 x 10.625HA Segment (Cast) 1.250 x 4.125
1618573 2 DB|_| 4 1.38 19.50 66.60 30.2121.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
966 G GII H Corner Guard System, Material Handling1331680 1331696 1331697 1331698 1331700 2151281 2151283Serial Number:
7I3015 1 WOSB 30Base Edge With Segment Holes 562.80 255.281.500 x 11.810 x 125.750
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 45©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1006668 2 DB|| 3 10.75 17.80 17.80 225.30 102.191.180 x 14.170 x 55.100Center 1.250
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1406823 2 DB|| 3 10.75 17.80 17.80 269.80 122.3831.375 x 14.170 x 55.100HD Center 1.250 x 4.125
1677430 2 DB|| 3 7.09 3.00 3.00 63.80 28.9431.625 x 20.180 x 8.000HD End 1.250 x 4.125
1359410 2 DB|| 3 10.75 17.81 17.81 325.40 147.6031.375 x 16.000 x 55.250Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1006668HA 3 HA|| 4 8.78 17.81 223.10 101.2021.750 x 15.625 x 35.375HA Center (Cast) 1.250 x 4.1252 8.78 17.81 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
1006668TP 3 DB|| 4 8.78 17.81 61.50 27.9021.000 x 12.586 x 35.375Bolt on Top Plate Center 1.250 x 52 8.78 17.81 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9931.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9931.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1006668HAN 3 HA|| 2 8.78 17.81 172.30 78.151.750 x 11.125 x 35.375Narrow HA Center (Cast) 1.250 x 4.125
1073287 1 SB|| 3 8.88 17.81 17.81 255.30 115.8031.375 x 12.000 x 55.250C/IMP Center NR RH 1.250 x 4.125
1073286 1 SB|| 3 8.88 17.81 17.81 255.30 115.8031.375 x 12.000 x 55.250C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 7J350 or J450 Options
1006666 7 DB|| 2 1.77 8.00 1.77 46.50 21.0921.180 x 14.170 x 11.540Segment 1.250 x 4.125
1406870 7 DB|| 2 1.77 8.00 54.90 24.9021.375 x 14.170 x 11.540HD Segment 1.250 x 4.125
1744116 7 HA|| 2 1.78 8.00 59.10 26.8121.750 x 13.500 x 11.563HA Segment (Cast) 1.250 x 4.125
1618573 2 DB|_| 4 1.38 19.50 66.60 30.2121.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
966 H Corner Guard System, Material Handling1468081 1475931 1619631 2628966 2628974Serial Number:
1471469 1 SB||Base Edge
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U1909 2 DB|| 3 9.25 16.25 16.25 205.20 93.0831.180 x 14.170 x 49.750Center 1.250 x 4.125
1069290 2 DB|| 3 7.13 3.00 3.00 62.10 28.1731.375 x 20.250 x 9.000End 1.250 x 4.125
TEETH 8J350 or J450 Options
1006664 7 DB|| 2 1.81 6.42 1.81 40.20 18.2321.180 x 14.170 x 10.039Segment 1.250 x 4.125
1406869 7 DB|| 2 1.81 6.42 47.60 21.591.375 x 14.173 x 10.039HD Segment 1.250
1618573 2 DB|_| 4 1.38 19.50 66.60 30.2121.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
966 H Material Handling2628964 2628971 2628972 2628979Serial Number:
2480571 1 SB||Base Edge For Bolt-on Edges Only
9W0775 2 DB|| 5 2.94 6.00 6.00 169.00 76.6651.375 x 16.000 x 29.875Center 1.250 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 46©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W6615 2 DB|| 5 4.69 6.00 6.00 191.00 86.6451.375 x 16.000 x 33.375End 1.250 x 3.75
2482419 2 DB|| 4Bolt-On Wear Plate 0.750
966 H Material Handling2628967Serial Number:
2687460 1 SB||Base Edge For Bolt-on Edges Only
9W6609 3 DB|| 6 4.56 6.00 6.00 225.80 102.4261.375 x 16.000 x 39.125Center 1.250 x 3.75
2482419 2 DB|| 4Bolt-On Wear Plate 0.750
966 H Material Handling, Flush Mount1468078 1468079 1468080 2628968 2628975 2628976Serial Number:
1492865 1 SB||Base Edge Without Holes
TEETH 8J350 Options
966 H Material Handling, Flush Mount1468083 2628969Serial Number:
1072842 1 SB||Base Edge Without Holes
TEETH 8J350 Options
966 D E F Flush Mounted Teeth6W5352 8R8206Serial Number:
6W5520BASE 1 SB||Base Edge Without Holes 1.250 x 10.500 x 119.700
TEETH 8J350 Options
966 C Multi-Purpose5V7338 5V7339Serial Number:
6W2989 1 WOSB 30Base Edge With Segment Holes 397.70 180.391.250 x 11.125 x 111.875
8E5320 1 IRR 2Corner 2 hole RH
8E5321 1 IRR 2Corner 2 hole LH
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
5V2772 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.938 x 9.844
5V2773 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.938 x 9.844
1U2407 2 DB|| 3 8.63 15.88 15.88 198.50 90.0431.180 x 14.170 x 48.125Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1359532 2 DB|| 3 8.63 15.88 15.88 283.00 128.3731.375 x 16.000 x 48.125Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
4T8378 1 DB|| 13 3.44 6.00 6.00 122.40 55.52130.750 x 8.000 x 78.875Multi purpose dozer center 0.750 x 2.25
4T8381 2 DB|| 3 3.88 5.50 5.50 26.00 11.7930.750 x 8.000 x 16.813Multi purpose dozer end 0.750 x 2.25
TEETH 8J350 Options
4T6698 7 DB|| 2 2.00 5.50 2.00 37.80 17.1521.180 x 14.170 x 9.500Segment 1.250 x 4.125
1406867 7 DB|| 2 2.00 5.50 44.90 20.3721.375 x 14.170 x 9.500HD Segment 1.250 x 4.125
4T6698FHA 7 HA|| 2 2.00 5.50 35.10 15.9221.250 x 10.500 x 9.500HA Segment (Fabricated) 1.250 x 4.125
966 C Multi-Purpose1V6370 1V7289Serial Number:
8K9754 1 WOSB 24Base Edge For Bolt-on Edges or Teeth 407.60 184.881.250 x 10.500 x 115.000
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 47©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T8378 1 DB|| 13 3.44 6.00 6.00 122.40 55.52130.750 x 8.000 x 78.875Multi purpose dozer center 0.750 x 2.25
4T8381 2 DB|| 3 3.88 5.50 5.50 26.00 11.7930.750 x 8.000 x 16.813Multi purpose dozer end 0.750 x 2.25
TEETH 8J300 Options
966 F Multi-Purpose7Q8337Serial Number:
9V6575 1 WOSB 30Base Edge With Segment Holes 534.00 242.221.500 x 11.811 x 119.750
7V1490 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 541.10 245.441.500 x 11.811 x 119.375
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U0593 2 DB|| 3 8.31 16.88 16.88 213.70 96.9331.180 x 14.170 x 51.875Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1004046 2 DB|| 3 8.25 16.88 16.88 305.30 138.4831.375 x 16.000 x 51.875Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1U0593HA 3 HA|| 4 8.31 16.88 211.20 95.8021.750 x 15.625 x 33.500HA Center (Cast) 1.250 x 4.1252 8.31 16.88 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
1U0593TP 3 DB|| 4 8.31 16.88 60.10 27.2621.000 x 12.586 x 33.500Bolt on Top Plate Center 1.250 x 52 8.31 16.88 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1U0593HAN 3 HA|| 2 8.31 16.88 163.10 73.981.750 x 11.125 x 33.500Narrow HA Center (Cast) 1.250 x 4.125
2085345 2 DB|| 3 9.88 16.88 16.88 237.00 107.5031.180 x 14.170 x 51.875C/IMP Center REV 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
9W3477 1 SB|| 3 9.81 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR RH 1.250 x 4.125
9W3478 1 SB|| 3 8.31 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
12783 1 DB||Multi purpose dozer center
4T8381 2 DB|| 3 3.88 5.50 5.50 26.00 11.7930.750 x 8.000 x 16.813Multi purpose dozer end 0.750 x 2.25
TEETH 8J350 or J450 Options
4T6699 7 DB|| 2 1.75 7.13 42.70 19.3721.180 x 14.170 x 10.625Segment 1.250 x 4.125
1406868 7 DB|| 2 1.75 7.13 1.75 49.80 22.5921.375 x 14.170 x 10.625HD Segment 1.250 x 4.125
1744114 7 HA|| 2 1.75 7.13 54.70 24.8131.750 x 13.500 x 10.625HA Segment (Cast) 1.250 x 4.125
966 C Spade Nose Rock7K1075Serial Number:
9V0169 1 SB\_/Spade Nose Base Edge 889.60 403.521.500 x 24.000 x 113.000
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
TEETH 6
966 D E F Spade Nose Rock5V4645 9V0954 8R8207 9V0963 8R8208 9V1807Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 48©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9V0170 1 SB\_/Spade Nose Base Edge Without Holes 883.20 400.611.500 x 22.750 x 121.500
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
TEETH 8J350 Options
9W6749 2 DB|| 4 1.38 19.50 69.70 31.6221.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
966 F Spade Nose Rock2Q3073 2Q2922Serial Number:
6W2993 1 SB\_/ 22Spade Nose Base For Segments 959.90 435.401.750 x 22.717 x 121.460
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
4T9185 1 DB|| 4 3.88 5.00 4.75 90.60 41.1041.180 x 14.170 x 22.500Center 1.250 x 3.75
4T9126 1 DB\\ 3 8.88 5.75 5.75 104.70 47.4931.180 x 14.170 x 29.250Center RH 1.250 x 3.75
4T9128 1 DB\\ 4 5.75 5.75 5.75 102.10 46.3141.180 x 14.170 x 28.750End RH 1.250 x 3.75
4T9125 1 DB// 3 8.88 5.75 5.75 104.70 47.4931.180 x 14.170 x 29.250Center LH 1.250 x 3.75
4T9127 1 DB// 4 5.75 5.75 5.75 102.10 46.3141.180 x 14.170 x 28.750End LH 1.250 x 3.75
TEETH 8J350 or J400 Options
4T6697 1 DB|| 2 1.75 4.75 1.75 32.80 14.8821.180 x 14.170 x 8.250Segment 1.250 x 3.75
4T9123 3 DB\\ 2 4.13 5.75 4.13 41.80 18.9621.180 x 14.170 x 14.000Segment RH 1.250 x 3.75
4T9124 3 DB// 2 4.13 5.75 4.13 41.80 18.9621.180 x 14.170 x 14.000Segment LH 1.250 x 3.75
1406866 1 DB|| 2 1.75 4.75 1.7521.375 x 14.170 x 8.250HD Segment 1.250 x 3.75
1406864 3 DB\\ 2 21.375 x 14.170 x 10.438HD Segment RH 1.250 x 3.75
1406863 3 DB// 2 21.375 x 14.170 x 10.438HD Segment LH 1.250 x 3.75
1359648 1 DB|| 2 1.75 4.75 1.752C/IMP Segment REV 1.250 x 3.75
1359649 3 DB\\ 2 4.13 5.75 4.132C/IMP Segment RH REV 1.250 x 3.75
1359647 3 DB// 2 4.13 5.75 4.132C/IMP Segment LH REV 1.250 x 3.75
9W6749 2 DB|| 4 1.38 19.50 69.70 31.6221.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
966 G GII H Spade Nose Rock1486908 1486909 2544500 2544501 2544502 2544503Serial Number:
1486915 1 SB\_/ 20Spade Nose Base Edge 936.60 424.831.500 x 24.213 x 128.030
1486935 2 IRRCorner LH/RH for 2-1358246 Protectors
1358246 4 IRRSidebar Protector 24.00 10.891.125 x 5.750 x 18.188
TEETH 8J350 Options
1359294 1 DB|| 2 3.55 4.72 3.55 65.60 29.7621.625 x 13.000 x 11.810Segment 1.250 x 3.25
1359295 3 DB\\ 2 4.00 7.91 4.00 69.00 31.3021.625 x 13.000 x 15.900Segment RH 1.250 x 3.25
1359296 3 DB// 2 4.00 7.91 4.00 69.00 31.3021.625 x 13.000 x 15.900Segment LH 1.250 x 3.25
1359544 1 HA|| 2 3.54 4.72 82.70 37.5121.750 x 18.315 x 11.811HA Segment (Cast) 1.250 x 3.25
1359545 3 HA\\ 2 1.31 7.91 86.20 39.1021.750 x 18.315 x 11.969HA Segment RH (Cast) 1.250 x 3.25
1359546 3 HA// 2 1.31 7.91 86.20 39.1021.750 x 18.315 x 11.969HA Segment LH (Cast) 1.250 x 3.25
6Y6351 1 DB|| 7 2.88 6.00 6.00 152.60 69.2241.375 x 10.000 x 41.750Base Edge Wear Plate 0.875 x 2.75
1618573 2 DB|_| 4 1.38 19.50 66.60 30.2121.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
966 G GII H Spade Nose Rock1486907 1486906 1486910Serial Number:
1541604 1 SB\_/ 22Spade Nose Base Edge 922.00 418.211.500 x 24.213 x 128.031
1486934 2 IRRCorner LH/RH for 2-1358246 Protectors
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 49©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1358246 4 IRRSidebar Protector 24.00 10.891.125 x 5.750 x 18.188
1358240 1 DB|| 4 2.60 6.42 4.72 108.40 49.171.375 x 14.173 x 22.756Center 1.250
1358241 1 DB\\ 4 4.30 7.91 10.43 149.60 67.861.375 x 14.170 x 34.861Center RH 1.250
1358243 1 DB\\ 4 4.47 5.24 7.91 112.20 50.891.375 x 14.173 x 27.321End RH 1.250
1358244 1 DB// 4 4.47 5.24 7.91 112.20 50.891.375 x 14.173 x 27.321Center LH 1.250
1358242 1 DB// 4 4.30 7.91 10.43 149.60 67.861.375 x 14.170 x 34.861End LH 1.250
6Y6351 1 DB|| 7 2.88 6.00 6.00 152.60 69.2241.375 x 10.000 x 41.750Base Edge Wear Plate 0.875 x 2.75
1618573 2 DB|_| 4 1.38 19.50 66.60 30.2121.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
970 Corner Guard System9U4834Serial Number:
7I3631 1 WOSB 30Base Edge With Segment Holes 514.30 233.281.500 x 11.800 x 115.160
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U1909 2 DB|| 3 9.25 16.25 16.25 205.20 93.0831.180 x 14.170 x 49.750Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1359533 2 DB|| 3 9.25 16.25 16.25 292.70 132.7731.375 x 16.000 x 49.750Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1073282 1 SB|| 3 9.25 16.25 16.2531.250 x 11.000 x 49.750C/IMP Center NR RH 1.250 x 4.125
1073283 1 SB|| 3 7.75 16.25 16.2531.250 x 11.000 x 49.750C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 8J350 or J450 Options
1006664 7 DB|| 2 1.81 6.42 1.81 40.20 18.231.180 x 14.170 x 10.039Segment 1.250
1406869 7 DB|| 2 1.81 6.42 47.60 21.591.375 x 14.173 x 10.039HD Segment 1.250
9W6749 2 DB|| 4 1.38 19.50 69.70 31.6221.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
970 F Corner Guard System8R8209 9U4833 9U4832 1270732 1270733Serial Number:
9V6575 1 WOSB 30Base Edge With Segment Holes 534.00 242.221.500 x 11.811 x 119.750
7V1490 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 541.10 245.441.500 x 11.811 x 119.375
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 50©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1U0593 2 DB|| 3 8.31 16.88 16.88 213.70 96.9331.180 x 14.170 x 51.875Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1004046 2 DB|| 3 8.25 16.88 16.88 305.30 138.4831.375 x 16.000 x 51.875Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1U0593HA 3 HA|| 4 8.31 16.88 211.20 95.8021.750 x 15.625 x 33.500HA Center (Cast) 1.250 x 4.1252 8.31 16.88 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
1U0593TP 3 DB|| 4 8.31 16.88 60.10 27.2621.000 x 12.586 x 33.500Bolt on Top Plate Center 1.250 x 52 8.31 16.88 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1U0593HAN 3 HA|| 2 8.31 16.88 163.10 73.981.750 x 11.125 x 33.500Narrow HA Center (Cast) 1.250 x 4.125
2085345 2 DB|| 3 9.88 16.88 16.88 237.00 107.5031.180 x 14.170 x 51.875C/IMP Center REV 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
9W3477 1 SB|| 3 9.81 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR RH 1.250 x 4.125
9W3478 1 SB|| 3 8.31 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 8J350 or J450 Options
4T6699 7 DB|| 2 1.75 7.13 42.70 19.3721.180 x 14.170 x 10.625Segment 1.250 x 4.125
1406868 7 DB|| 2 1.75 7.13 1.75 49.80 22.5921.375 x 14.170 x 10.625HD Segment 1.250 x 4.125
1744114 7 HA|| 2 1.75 7.13 54.70 24.8131.750 x 13.500 x 10.625HA Segment (Cast) 1.250 x 4.125
9W6749 2 DB|| 4 1.38 19.50 69.70 31.6221.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
970 F Corner Guard System9U4835 1056113 1270731 1107728 1270730 1270735Serial Number:
7I3015 1 WOSB 30Base Edge With Segment Holes 562.80 255.281.500 x 11.810 x 125.750
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1006668 2 DB|| 3 10.75 17.80 17.80 225.30 102.191.180 x 14.170 x 55.100Center 1.250
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1406823 2 DB|| 3 10.75 17.80 17.80 269.80 122.3831.375 x 14.170 x 55.100HD Center 1.250 x 4.125
1677430 2 DB|| 3 7.09 3.00 3.00 63.80 28.9431.625 x 20.180 x 8.000HD End 1.250 x 4.125
1359410 2 DB|| 3 10.75 17.81 17.81 325.40 147.6031.375 x 16.000 x 55.250Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1006668HA 3 HA|| 4 8.78 17.81 223.10 101.2021.750 x 15.625 x 35.375HA Center (Cast) 1.250 x 4.1252 8.78 17.81 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 51©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1006668TP 3 DB|| 4 8.78 17.81 61.50 27.9021.000 x 12.586 x 35.375Bolt on Top Plate Center 1.250 x 52 8.78 17.81 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9931.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9931.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1006668HAN 3 HA|| 2 8.78 17.81 172.30 78.151.750 x 11.125 x 35.375Narrow HA Center (Cast) 1.250 x 4.125
1073287 1 SB|| 3 8.88 17.81 17.81 255.30 115.8031.375 x 12.000 x 55.250C/IMP Center NR RH 1.250 x 4.125
1073286 1 SB|| 3 8.88 17.81 17.81 255.30 115.8031.375 x 12.000 x 55.250C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 7J350 or J450 Options
1006666 7 DB|| 2 1.77 8.00 1.77 46.50 21.0921.180 x 14.170 x 11.540Segment 1.250 x 4.125
1406870 7 DB|| 2 1.77 8.00 54.90 24.9021.375 x 14.170 x 11.540HD Segment 1.250 x 4.125
1744116 7 HA|| 2 1.78 8.00 59.10 26.8121.750 x 13.500 x 11.563HA Segment (Cast) 1.250 x 4.125
9W6749 2 DB|| 4 1.38 19.50 69.70 31.6221.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
972 G GII H Corner Guard System1331676 1311681 2151282Serial Number:
9V6575 1 WOSB 30Base Edge With Segment Holes 534.00 242.221.500 x 11.811 x 119.750
7V1490 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 541.10 245.441.500 x 11.811 x 119.375
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U0593 2 DB|| 3 8.31 16.88 16.88 213.70 96.9331.180 x 14.170 x 51.875Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1004046 2 DB|| 3 8.25 16.88 16.88 305.30 138.4831.375 x 16.000 x 51.875Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1U0593HA 3 HA|| 4 8.31 16.88 211.20 95.8021.750 x 15.625 x 33.500HA Center (Cast) 1.250 x 4.1252 8.31 16.88 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
1U0593TP 3 DB|| 4 8.31 16.88 60.10 27.2621.000 x 12.586 x 33.500Bolt on Top Plate Center 1.250 x 52 8.31 16.88 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9921.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1U0593HAN 3 HA|| 2 8.31 16.88 163.10 73.981.750 x 11.125 x 33.500Narrow HA Center (Cast) 1.250 x 4.125
2085345 2 DB|| 3 9.88 16.88 16.88 237.00 107.5031.180 x 14.170 x 51.875C/IMP Center REV 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
9W3477 1 SB|| 3 9.81 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR RH 1.250 x 4.125
9W3478 1 SB|| 3 8.31 16.88 16.88 220.00 99.7931.375 x 11.000 x 51.875C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 52©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J350 or J450 Options
4T6699 7 DB|| 2 1.75 7.13 42.70 19.3721.180 x 14.170 x 10.625Segment 1.250 x 4.125
1406868 7 DB|| 2 1.75 7.13 1.75 49.80 22.5921.375 x 14.170 x 10.625HD Segment 1.250 x 4.125
1744114 7 HA|| 2 1.75 7.13 54.70 24.8131.750 x 13.500 x 10.625HA Segment (Cast) 1.250 x 4.125
1618573 2 DB|_| 4 1.38 19.50 66.60 30.2121.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
972 G GII H Corner Guard System1331700 1331697 1331696 1470444 1470133 1470668 1475930 1470154 2131177 2151281 2151283 2560542Serial Number:
7I3015 1 WOSB 30Base Edge With Segment Holes 562.80 255.281.500 x 11.810 x 125.750
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1006668 2 DB|| 3 10.75 17.80 17.80 225.30 102.191.180 x 14.170 x 55.100Center 1.250
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1406823 2 DB|| 3 10.75 17.80 17.80 269.80 122.3831.375 x 14.170 x 55.100HD Center 1.250 x 4.125
1677430 2 DB|| 3 7.09 3.00 3.00 63.80 28.9431.625 x 20.180 x 8.000HD End 1.250 x 4.125
1359410 2 DB|| 3 10.75 17.81 17.81 325.40 147.6031.375 x 16.000 x 55.250Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1006668HA 3 HA|| 4 8.78 17.81 223.10 101.2021.750 x 15.625 x 35.375HA Center (Cast) 1.250 x 4.1252 8.78 17.81 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
1006668TP 3 DB|| 4 8.78 17.81 61.50 27.9021.000 x 12.586 x 35.375Bolt on Top Plate Center 1.250 x 52 8.78 17.81 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9931.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9931.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1006668HAN 3 HA|| 2 8.78 17.81 172.30 78.151.750 x 11.125 x 35.375Narrow HA Center (Cast) 1.250 x 4.125
1073287 1 SB|| 3 8.88 17.81 17.81 255.30 115.8031.375 x 12.000 x 55.250C/IMP Center NR RH 1.250 x 4.125
1073286 1 SB|| 3 8.88 17.81 17.81 255.30 115.8031.375 x 12.000 x 55.250C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 7J350 or J450 Options
1006666 7 DB|| 2 1.77 8.00 1.77 46.50 21.0921.180 x 14.170 x 11.540Segment 1.250 x 4.125
1406870 7 DB|| 2 1.77 8.00 54.90 24.9021.375 x 14.170 x 11.540HD Segment 1.250 x 4.125
1744116 7 HA|| 2 1.78 8.00 59.10 26.8121.750 x 13.500 x 11.563HA Segment (Cast) 1.250 x 4.125
1618573 2 DB|_| 4 1.38 19.50 66.60 30.2121.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
972 H Corner Guard System, Material Handling2513035 2513036 2513038 2513056 2513058 2855007 2855011 2855015 2855009 2855013 2855016 2628955Serial Number:
7I3015 1 WOSB 30Base Edge With Segment Holes 562.80 255.281.500 x 11.810 x 125.750
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 53©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1006668 2 DB|| 3 10.75 17.80 17.80 225.30 102.191.180 x 14.170 x 55.100Center 1.250
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
1406823 2 DB|| 3 10.75 17.80 17.80 269.80 122.3831.375 x 14.170 x 55.100HD Center 1.250 x 4.125
1677430 2 DB|| 3 7.09 3.00 3.00 63.80 28.9431.625 x 20.180 x 8.000HD End 1.250 x 4.125
1359410 2 DB|| 3 10.75 17.81 17.81 325.40 147.6031.375 x 16.000 x 55.250Heavy Duty Wider Center 1.250 x 4.125
1004044 2 DB|| 3 8.00 3.00 3.00 74.50 33.7931.625 x 22.000 x 8.000Heavy Duty Wider End 1.250 x 4.125
1006668HA 3 HA|| 4 8.78 17.81 223.10 101.2021.750 x 15.625 x 35.375HA Center (Cast) 1.250 x 4.1252 8.78 17.81 ...2nd Row1.250 x 4.125
3G6395HAR 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End RH (Cast) 1.250 x 4.125
3G6395HAL 1 HA|| 3 4.00 3.00 3.00 69.20 31.3931.750 x 15.625 x 9.500HA End LH (Cast) 1.250 x 4.125
1006668TP 3 DB|| 4 8.78 17.81 61.50 27.9021.000 x 12.586 x 35.375Bolt on Top Plate Center 1.250 x 52 8.78 17.81 ...2nd Row1.250 x 5
3G6395TPR 1 DB|\ 3 3.00 2.97 2.97 13.20 5.9931.000 x 12.586 x 5.750Bolt on Top Plate RH 1.250 x 5
3G6395TPL 1 DB/| 3 3.00 2.97 2.97 13.20 5.9931.000 x 12.586 x 5.750Bolt on Top Plate LH 1.250 x 5
1006668HAN 3 HA|| 2 8.78 17.81 172.30 78.151.750 x 11.125 x 35.375Narrow HA Center (Cast) 1.250 x 4.125
1073287 1 SB|| 3 8.88 17.81 17.81 255.30 115.8031.375 x 12.000 x 55.250C/IMP Center NR RH 1.250 x 4.125
1073286 1 SB|| 3 8.88 17.81 17.81 255.30 115.8031.375 x 12.000 x 55.250C/IMP Center NR LH 1.250 x 4.125
1230336 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR RH 1.250 x 4.125
1230337 1 SB|| 3 5.11 3.00 3.00 54.60 24.7731.375 x 18.250 x 8.000C/IMP End NR LH 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 7J350 or J450 Options
1006666 7 DB|| 2 1.77 8.00 1.77 46.50 21.0921.180 x 14.170 x 11.540Segment 1.250 x 4.125
1406870 7 DB|| 2 1.77 8.00 54.90 24.9021.375 x 14.170 x 11.540HD Segment 1.250 x 4.125
1744116 7 HA|| 2 1.78 8.00 59.10 26.8121.750 x 13.500 x 11.563HA Segment (Cast) 1.250 x 4.125
2482419 2 DB|| 4Bolt-On Wear Plate 0.750
972 G Spade Nose Rock1486913 1486912 1486908Serial Number:
1486915 1 SB\_/ 20Spade Nose Base Edge 936.60 424.831.500 x 24.213 x 128.030
1486935 2 IRRCorner LH/RH for 2-1358246 Protectors
1358246 4 IRRSidebar Protector 24.00 10.891.125 x 5.750 x 18.188
TEETH 8J350 Options
1359294 1 DB|| 2 3.55 4.72 3.55 65.60 29.7621.625 x 13.000 x 11.810Segment 1.250 x 3.25
1359295 3 DB\\ 2 4.00 7.91 4.00 69.00 31.3021.625 x 13.000 x 15.900Segment RH 1.250 x 3.25
1359296 3 DB// 2 4.00 7.91 4.00 69.00 31.3021.625 x 13.000 x 15.900Segment LH 1.250 x 3.25
1359544 1 HA|| 2 3.54 4.72 82.70 37.5121.750 x 18.315 x 11.811HA Segment (Cast) 1.250 x 3.25
1359545 3 HA\\ 2 1.31 7.91 86.20 39.1021.750 x 18.315 x 11.969HA Segment RH (Cast) 1.250 x 3.25
1359546 3 HA// 2 1.31 7.91 86.20 39.1021.750 x 18.315 x 11.969HA Segment LH (Cast) 1.250 x 3.25
6Y6351 1 DB|| 7 2.88 6.00 6.00 152.60 69.2241.375 x 10.000 x 41.750Base Edge Wear Plate 0.875 x 2.75
1618573 2 DB|_| 4 1.38 19.50 66.60 30.2121.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
972 G GII H Spade Nose Rock1486906 1486910 1486911Serial Number:
1541604 1 SB\_/ 22Spade Nose Base Edge 922.00 418.211.500 x 24.213 x 128.031
1486934 2 IRRCorner LH/RH for 2-1358246 Protectors
1358246 4 IRRSidebar Protector 24.00 10.891.125 x 5.750 x 18.188
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 54©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1358240 1 DB|| 4 2.60 6.42 4.72 108.40 49.171.375 x 14.173 x 22.756Center 1.250
1358241 1 DB\\ 4 4.30 7.91 10.43 149.60 67.861.375 x 14.170 x 34.861Center RH 1.250
1358243 1 DB\\ 4 4.47 5.24 7.91 112.20 50.891.375 x 14.173 x 27.321End RH 1.250
1358244 1 DB// 4 4.47 5.24 7.91 112.20 50.891.375 x 14.173 x 27.321Center LH 1.250
1358242 1 DB// 4 4.30 7.91 10.43 149.60 67.861.375 x 14.170 x 34.861End LH 1.250
6Y6351 1 DB|| 7 2.88 6.00 6.00 152.60 69.2241.375 x 10.000 x 41.750Base Edge Wear Plate 0.875 x 2.75
1618573 2 DB|_| 4 1.38 19.50 66.60 30.2121.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
973 Corner Guard System5V0517Serial Number:
6W2982 1 WOSB 30Base Edge With Segment Holes 452.30 205.161.500 x 11.813 x 102.625
5V0600 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 460.60 208.921.500 x 11.812 x 102.625
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U0591 2 DB|| 3 7.44 14.50 14.50 177.00 80.2931.180 x 14.170 x 43.563Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 7J350 or J450 Options
4T6697 7 DB|| 2 1.75 4.75 1.75 32.80 14.8821.180 x 14.170 x 8.250Segment 1.250 x 4.125
1406866 7 DB|| 2 1.75 4.75 1.7521.375 x 14.170 x 8.250HD Segment 1.250 x 4.125
1359648 7 DB|| 2 1.75 4.75 1.752C/IMP Segment REV 1.250 x 4.125
9W6749 2 DB|| 4 1.38 19.50 69.70 31.6221.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
973 Flush Mounted Teeth9V5294Serial Number:
9V5287 1 WOSBBase Edge Without Holes 493.00 223.621.500 x 11.500 x 106.000
6W2453 1 IRRCorner no holes RH
6W2454 1 IRRCorner no holes LH
TEETH 8J350 or J450 Options
9W6750 1 DB|_| 4 1.38 20.75 69.80 31.6621.375 x 10.000 x 23.500Rear Wear Plate 0.750 x 2.52 1.38 20.75 ...2nd Row0.750 x 2.5
973 Corner Guard System4V9677Serial Number:
6W2981 1 WOSB 30Base Edge With Segment Holes 498.70 226.211.500 x 11.811 x 112.047
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 55©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U2406 2 DB|| 3 8.88 15.88 15.88 199.50 90.4931.180 x 14.170 x 48.375Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 7J350 or J450 Options
4T6698 7 DB|| 2 2.00 5.50 2.00 37.80 17.1521.180 x 14.170 x 9.500Segment 1.250 x 4.125
1406867 7 DB|| 2 2.00 5.50 44.90 20.3721.375 x 14.170 x 9.500HD Segment 1.250 x 4.125
4T6698FHA 7 HA|| 2 2.00 5.50 35.10 15.9221.250 x 10.500 x 9.500HA Segment (Fabricated) 1.250 x 4.125
9W6749 2 DB|| 4 1.38 19.50 69.70 31.6221.375 x 10.000 x 22.250Rear Wear Plate 0.750 x 2.52 1.38 19.50 ...2nd Row0.750 x 2.5
973 Flush Mounted Teeth9V5292Serial Number:
9V5283 1 WOSBBase Edge Without Holes 537.00 243.581.500 x 11.500 x 115.500
6W2453 1 IRRCorner no holes RH
6W2454 1 IRRCorner no holes LH
TEETH 8J350 or J450 Options
9W6750 1 DB|_| 4 1.38 20.75 69.80 31.6621.375 x 10.000 x 23.500Rear Wear Plate 0.750 x 2.52 1.38 20.75 ...2nd Row0.750 x 2.5
973 Multi-Purpose5V2744 5V2742Serial Number:
6W2982 1 WOSB 30Base Edge With Segment Holes 452.30 205.161.500 x 11.813 x 102.625
5V0600 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 460.60 208.921.500 x 11.812 x 102.625
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U0591 2 DB|| 3 7.44 14.50 14.50 177.00 80.2931.180 x 14.170 x 43.563Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
4T8374 1 DB|| 16 5.50 6.00 6.00 156.80 71.12160.750 x 8.000 x 101.000Multi purpose dozer center 0.750 x 2.75
TEETH 7J350 or J450 Options
4T6697 7 DB|| 2 1.75 4.75 1.75 32.80 14.8821.180 x 14.170 x 8.250Segment 1.250 x 4.125
1406866 7 DB|| 2 1.75 4.75 1.7521.375 x 14.170 x 8.250HD Segment 1.250 x 4.125
1359648 7 DB|| 2 1.75 4.75 1.752C/IMP Segment REV 1.250 x 4.125
973 Multi-Purpose9V4315 5V2742Serial Number:
6W2982 1 WOSB 30Base Edge With Segment Holes 452.30 205.161.500 x 11.813 x 102.625
5V0600 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 460.60 208.921.500 x 11.812 x 102.625
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 56©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U0591 2 DB|| 3 7.44 14.50 14.50 177.00 80.2931.180 x 14.170 x 43.563Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
4T8379 1 DB|| 11 1.94 6.00 6.00 98.90 44.86110.750 x 8.000 x 63.875Multi purpose dozer center 0.750 x 2.75
4T8353 2 DB|| 3 3.13 6.00 6.00 28.30 12.8430.750 x 8.000 x 18.250Multi purpose dozer end 0.750 x 2.75
TEETH 7J350 or J450 Options
4T6697 7 DB|| 2 1.75 4.75 1.75 32.80 14.8821.180 x 14.170 x 8.250Segment 1.250 x 4.125
1406866 7 DB|| 2 1.75 4.75 1.7521.375 x 14.170 x 8.250HD Segment 1.250 x 4.125
1359648 7 DB|| 2 1.75 4.75 1.752C/IMP Segment REV 1.250 x 4.125
973 Multi-Purpose5V7305 5V2742Serial Number:
5G7304 1 WOSB 30Base Edge With Segment Holes 473.50 214.781.500 x 11.813 x 106.375
5G7303 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 481.00 218.181.500 x 11.813 x 106.375
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
9W8334 2 DB|| 3 7.50 15.25 15.25 187.60 85.0931.180 x 14.170 x 45.500Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
9W8335 1 DB|| 11 3.94 6.00 6.00 105.30 47.76110.750 x 8.000 x 67.875Multi purpose dozer center 0.750 x 2.75
4T8353 2 DB|| 3 3.13 6.00 6.00 28.30 12.8430.750 x 8.000 x 18.250Multi purpose dozer end 0.750 x 2.75
TEETH 7J350 or J450 Options
4T6697 7 DB|| 2 1.75 4.75 1.75 32.80 14.8821.180 x 14.170 x 8.250Segment 1.250 x 4.125
1406866 7 DB|| 2 1.75 4.75 1.7521.375 x 14.170 x 8.250HD Segment 1.250 x 4.125
1359648 7 DB|| 2 1.75 4.75 1.752C/IMP Segment REV 1.250 x 4.125
973 Spade Nose Rock5V7346Serial Number:
9V0171 1 SB\_/Spade Nose Base Edge Without Holes 1.500 x 18.500 x 106.500
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
TEETH 8J350 or J450 Options
7V0910 2 DB|_| 4 1.44 20.75 96.00 43.5421.625 x 11.500 x 23.625Rear Wear Plate 0.750 x 2.52 1.44 20.75 ...2nd Row0.750 x 2.5
973 Spade Nose Rock5V7346Serial Number:
6W2994 1 SB\_/ 16Spade Nose Base Edge 866.20 392.901.750 x 19.530 x 106.500
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 57©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W3676 1 DB|| 4 7.11 5.28 11.34 273.10 123.881.750 x 16.000 x 36.125Center 1.250 x 3.75
9W3678 1 DB\\ 6 6.00 5.71 5.71 281.00 127.461.750 x 16.000 x 40.547End RH 1.250 x 3.75
9W3677 1 DB// 6 6.00 5.71 5.71 281.00 127.461.750 x 16.000 x 40.546End LH 1.250 x 3.75
TEETH 8J350 or J450 Options
4T3015 2 DB|| 2 2.44 5.25 40.50 18.3721.180 x 14.170 x 10.125Segment 1.250 x 3.75
4T9123 2 DB\\ 2 4.13 5.75 4.13 41.80 18.9621.180 x 14.170 x 14.000Segment RH 1.250 x 3.75
4T9124 2 DB// 2 4.13 5.75 4.13 41.80 18.9621.180 x 14.170 x 14.000Segment LH 1.250 x 3.75
1321038 1 DB|| 2 2.44 5.25 48.00 21.7721.375 x 14.250 x 10.125HD Segment 1.250 x 3.25
1321039 3 DB\\ 2 4.13 5.75 50.00 22.6821.375 x 14.250 x 14.000HD Segment RH 1.250 x 3.25
1321040 3 DB// 2 4.13 5.75 4.13 50.00 22.6821.375 x 14.250 x 14.000HD Segment LH 1.250 x 3.25
7V0910 2 DB|_| 4 1.44 20.75 96.00 43.5421.625 x 11.500 x 23.625Rear Wear Plate 0.750 x 2.52 1.44 20.75 ...2nd Row0.750 x 2.5
973 Slag5V7344Serial Number:
9V0255 1 WOSBBase Edge Without Holes 703.00 318.882.000 x 13.000 x 106.875
7V7941 2 IRRCorner no holes LH/RH
TEETH 6J450 Options
977 Corner Guard System5V7349 5V7351Serial Number:
6W2983 1 WOSB 30Base Edge With Segment Holes 424.30 192.461.500 x 11.813 x 95.750
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U2408 2 DB|| 3 6.25 13.56 13.56 163.00 73.9431.180 x 14.170 x 40.063Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 7J350 or J450 Options
4T6696 7 DB|| 2 2.00 3.50 2.00 29.60 13.4321.180 x 14.170 x 7.500Segment 1.250 x 4.125
1406865 7 DB|| 2 2.00 3.50 2.0021.375 x 14.170 x 7.500HD Segment 1.250 x 4.125
9V6106 2 DB||Weld-On Wear Plate
977 General Purpose8K9500 8K9501 8K7850 8K7391Serial Number:
8K9499 1 WOSB 21Base Edge For Bolt-on Edges or Teeth 335.00 151.951.250 x 10.500 x 98.000
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
1U1478 1 DB|| 8 6.25 3.25 10.50 240.00 108.8681.180 x 14.170 x 55.875Center RH 1.000 x 3
1U1479 1 DB|| 6 6.13 3.25 10.50 170.00 77.1161.180 x 14.170 x 42.000Center LH 1.000 x 3
TEETH 7J350 Options
9V6106 2 DB||Weld-On Wear Plate
977 Flush Mounted Teeth8K8497 1V8901 1V8905 9K8463Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 58©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9K8472 1 WOSBBase Edge Without Holes 346.00 156.941.250 x 10.500 x 98.000
1V8664 2 IRRCorner no holes LH/RH 15.90 7.211.250 x 7.000 x 9.500
TEETH 6J350 Options
9V6106 2 DB||Weld-On Wear Plate
977 Corner Guard System2V5683 5V7350Serial Number:
7V0898 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 497.20 225.531.500 x 11.750 x 110.500
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U2409 2 DB|| 3 8.25 15.75 15.75 214.00 97.0731.180 x 14.170 x 47.500Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
TEETH 7J350 or J450 Options
4T6696 7 DB|| 2 2.00 3.50 2.00 29.60 13.4321.180 x 14.170 x 7.500Segment 1.250 x 4.125
1406865 7 DB|| 2 2.00 3.50 2.0021.375 x 14.170 x 7.500HD Segment 1.250 x 4.125
9V6106 2 DB||Weld-On Wear Plate
977 Multi-Purpose5V7348 5V7347Serial Number:
6W2983 1 WOSB 30Base Edge With Segment Holes 424.30 192.461.500 x 11.813 x 95.750
4V7175FAB 1 IRR 1Corner 1 hole RH 21.30 9.661.375 x 8.787 x 9.662
4V7174FAB 1 IRR 1Corner 1 hole LH 21.30 9.661.375 x 8.787 x 9.662
8E5310 1 IRR 2Corner 2 hole RH 29.20 13.242.000 x 8.750 x 10.750
8E5311 1 IRR 2Corner 2 hole LH 29.20 13.242.000 x 8.750 x 10.750
2530064 1 IRR 2New Style 2 Hole Corner Protector RH 38.90 17.641.250 x 8.938 x 15.000
2530065 1 IRR 2New Style 2 Hole Corner Protector LH 38.90 17.641.250 x 8.938 x 15.000
1735426 1 IRR 2Old Style 2 Hole Corner Protector RH 30.20 13.701.250 x 8.750 x 13.000
1735427 1 IRR 2Old Style 2 Hole Corner Protector LH 30.20 13.701.250 x 8.750 x 13.000
1U2408 2 DB|| 3 6.25 13.56 13.56 163.00 73.9431.180 x 14.170 x 40.063Center 1.250 x 4.125
3G6395 2 DB|| 3 7.13 3.00 3.00 54.80 24.8631.375 x 20.252 x 8.000End 1.250 x 4.125
2085343 2 DB|| 3 7.13 3.00 3.00 61.00 27.6731.375 x 20.250 x 8.000C/IMP End REV 1.250 x 4.125
4T8375 1 DB|| 15 4.50 6.00 6.00 144.20 65.41150.750 x 8.000 x 93.000Multi purpose dozer center 0.750 x 2.5
TEETH 7J350 or J450 Options
4T6696 7 DB|| 2 2.00 3.50 2.00 29.60 13.4321.180 x 14.170 x 7.500Segment 1.250 x 4.125
1406865 7 DB|| 2 2.00 3.50 2.0021.375 x 14.170 x 7.500HD Segment 1.250 x 4.125
977 Multi-Purpose1V3511 1V3669Serial Number:
8K9499 1 WOSB 21Base Edge For Bolt-on Edges or Teeth 335.00 151.951.250 x 10.500 x 98.000
8K7525 1 IRRCorner no holes RH 29.20 13.241.750 x 9.000 x 9.750
8K7526 1 IRRCorner no holes LH 29.20 13.241.750 x 9.000 x 9.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 59©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1U1478 1 DB|| 8 6.25 3.25 10.50 240.00 108.8681.180 x 14.170 x 55.875Center RH 1.000 x 3
1U1479 1 DB|| 6 6.13 3.25 10.50 170.00 77.1161.180 x 14.170 x 42.000Center LH 1.000 x 3
4T8375 1 DB|| 15 4.50 6.00 6.00 144.20 65.41150.750 x 8.000 x 93.000Multi purpose dozer center 0.750 x 2.5
TEETH 7J350 Options
9V6106 2 DB||Weld-On Wear Plate
980 B Corner Guard System9K1415 9K1447 9K1448Serial Number:
6W2991 1 WOSB 30Base Edge With Segment Holes 690.20 313.071.750 x 12.000 x 125.125
9V1327 1 SB|| 18Base Edge For Bolt-on Edges Only 201.00 91.171.750 x 12.000 x 125.125
6I8249FAB 1 IRR 2Corner 2 hole RH 46.90 21.272.500 x 10.002 x 11.750
6I8250FAB 1 IRR 2Corner 2 hole LH 46.90 21.272.500 x 10.002 x 11.750
2530066 1 IRR 2New Style 2 Hole Corner Protector RH 69.60 31.571.375 x 10.375 x 17.500
2530067 1 IRR 2New Style 2 Hole Corner Protector LH 69.60 31.571.375 x 10.375 x 17.500
1735428 1 IRR 2Old Style 2 Hole Corner Protector RH 35.80 16.241.250 x 9.250 x 14.500
1735429 1 IRR 2Old Style 2 Hole Corner Protector LH 35.80 16.241.250 x 9.250 x 14.500
7V4181 1 IRR 1Corner 1 hole RH 31.50 14.291.625 x 10.000 x 11.500
7V4180 1 IRR 1Corner 1 hole LH 31.44 14.261.625 x 10.000 x 11.500
4T5273 2 DB|| 3 8.69 17.63 17.63 309.80 140.5231.375 x 16.000 x 52.625Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
1078572 2 DB|| 3 8.69 17.63 17.63 369.90 167.7831.625 x 16.000 x 52.625HD Center 1.250 x 4.125
1004043 2 DB|| 3 7.88 3.13 3.13 105.50 47.8531.750 x 22.000 x 10.375HD End 1.250 x 4.125
TEETH 8J350 or J450 Options
4T6700 7 DB|| 2 2.59 6.31 2.59 46.40 21.0521.180 x 14.170 x 11.500Segment 1.250 x 4.125
1078580 7 DB|| 2 2.59 6.31 2.59 68.90 31.2521.750 x 14.250 x 11.500HD Segment 1.250 x 4.125
1737447 7 HA|| 2 2.53 6.31 59.10 26.8121.750 x 13.750 x 11.375HA Segment (Cast) 1.250 x 4.125
980 B General Purpose9K1415 9K1447 9K1448Serial Number:
9K1619 1 WOSB 24Base Edge For Bolt-on Edges or Teeth 706.10 320.281.750 x 12.000 x 128.750
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
4T6594 1 DB|| 8 4.81 3.25 12.63 354.20 160.6681.375 x 16.000 x 60.500Center 1.000 x 3.5
4T6592 2 DB|| 4 7.19 3.25 12.63 196.40 89.0941.375 x 16.000 x 33.500End 1.000 x 3.5
1078578 1 DB|| 8 4.81 3.25 12.63 423.90 192.2881.750 x 16.000 x 60.500HD Center 1.000 x 3.5
1078577 2 DB|| 4 7.19 3.25 12.63 235.20 106.6841.750 x 16.000 x 33.500HD End 1.000 x 3.5
2174852 1 DB|| 1.375 x 16.000 x 60.500C/IMP Center REV
2174851 2 DB|| 1.375 x 16.000 x 33.500C/IMP End REV
TEETH 8J350 or J450 Options
980 B Flush Mounted Teeth2V6338Serial Number:
2V6118 1 WOSBBase Edge Without Holes 678.60 307.811.750 x 12.000 x 129.375
2V6299 2 IRRCorner no holes LH/RH
TEETH 9J350 Options
980 C Corner Guard System6W7800 8R6478Serial Number:
9V6574 1 WOSB 30Base Edge With Segment Holes 706.30 320.371.750 x 12.000 x 130.500
7V4188 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 718.40 325.861.750 x 12.000 x 130.500
6I8249FAB 1 IRR 2Corner 2 hole RH 46.90 21.272.500 x 10.002 x 11.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 60©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6I8250FAB 1 IRR 2Corner 2 hole LH 46.90 21.272.500 x 10.002 x 11.750
2530066 1 IRR 2New Style 2 Hole Corner Protector RH 69.60 31.571.375 x 10.375 x 17.500
2530067 1 IRR 2New Style 2 Hole Corner Protector LH 69.60 31.571.375 x 10.375 x 17.500
1735428 1 IRR 2Old Style 2 Hole Corner Protector RH 35.80 16.241.250 x 9.250 x 14.500
1735429 1 IRR 2Old Style 2 Hole Corner Protector LH 35.80 16.241.250 x 9.250 x 14.500
7V4181 1 IRR 1Corner 1 hole RH 31.50 14.291.625 x 10.000 x 11.500
7V4180 1 IRR 1Corner 1 hole LH 31.44 14.261.625 x 10.000 x 11.500
1U0762 2 DB|| 3 9.13 18.50 18.50 324.90 147.3731.375 x 16.000 x 55.250Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
1004047 2 DB|| 3 9.19 18.50 18.50 387.80 175.9031.625 x 16.000 x 55.375HD Center 1.250 x 4.125
1004043 2 DB|| 3 7.88 3.13 3.13 105.50 47.8531.750 x 22.000 x 10.375HD End 1.250 x 4.125
1368758 2 DB|| 3 9.13 18.50 18.50 445.80 202.2132.000 x 16.000 x 55.250Extra HD Center 1.250 x 4.125
1368759 2 DB|| 3 7.88 3.13 3.13 114.50 51.9432.000 x 22.000 x 10.375Extra HD End 1.250 x 4.125
2174725 3 HA|| 4 9.13 18.50 254.90 115.6221.750 x 16.750 x 36.750HA Center (Cast) 1.250 x 4.1252 9.13 18.50 ...2nd Row1.250 x 4.125
2174726 2 HA|| 6 4.13 3.12 3.12 82.50 37.4231.875 x 16.750 x 10.500HA End (Cast) 1.250 x 4.1253 4.13 3.13 3.13 ...2nd Row1.250 x 4.125
2174725TP 3 DB|| 4 9.13 18.50 91.27 41.4021.250 x 13.515 x 36.750Bolt on Top Plate Center 1.250 x 52 9.13 18.50 ...2nd Row1.250 x 5
2174726TPR 1 DB|\ 3 7.23 3.07 3.07 18.40 8.3531.250 x 13.372 x 6.000Bolt on Top Plate RH 1.250 x 5
2174726TPL 1 DB/| 3 7.23 3.07 3.07 18.40 8.3531.250 x 13.372 x 6.000Bolt on Top Plate LH 1.250 x 5
2174725N 3 HA|| 2 9.13 18.50 221.10 100.2921.875 x 12.750 x 36.750Narrow HA Center (Cast) 1.250 x 4.125
2085344 2 DB|| 3 3C/IMP Center REV 1.250 x 4.125
2085177 2 DB|| 3 7.88 3.13 3.13 102.70 46.5831.625 x 22.000 x 10.375C/IMP End REV 1.250 x 4.125
6Y3271 2 SB|| 3 9.13 18.50 18.50 280.90 127.4131.375 x 13.000 x 55.250C/IMP Center NR LH/RH 1.250 x 4.125
1230334 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR LH 1.250 x 4.125
1230335 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR RH 1.250 x 4.125
TEETH 8J350 or J450 Options
4T6700 7 DB|| 2 2.59 6.31 2.59 46.40 21.0521.180 x 14.170 x 11.500Segment 1.250 x 4.125
1078580 7 DB|| 2 2.59 6.31 2.59 68.90 31.2521.750 x 14.250 x 11.500HD Segment 1.250 x 4.125
1737447 7 HA|| 2 2.53 6.31 59.10 26.8121.750 x 13.750 x 11.375HA Segment (Cast) 1.250 x 4.125
9W6750 1 DB|_| 4 1.38 20.75 69.80 31.6621.375 x 10.000 x 23.500Rear Wear Plate 0.750 x 2.52 1.38 20.75 ...2nd Row0.750 x 2.5
980 C Corner Guard System5V7354Serial Number:
7V0909 1 WOSB 12Base Edge For Bolt-on Edges Only 622.00 282.131.500 x 11.813 x 130.875
7V9270 1 IRRCorner no holes RH 31.80 14.421.625 x 10.000 x 11.500
7V9271 1 IRRCorner no holes LH 31.80 14.421.625 x 10.000 x 11.500
1U0762 2 DB|| 3 9.13 18.50 18.50 324.90 147.3731.375 x 16.000 x 55.250Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
1004047 2 DB|| 3 9.19 18.50 18.50 387.80 175.9031.625 x 16.000 x 55.375HD Center 1.250 x 4.125
1004043 2 DB|| 3 7.88 3.13 3.13 105.50 47.8531.750 x 22.000 x 10.375HD End 1.250 x 4.125
1368758 2 DB|| 3 9.13 18.50 18.50 445.80 202.2132.000 x 16.000 x 55.250Extra HD Center 1.250 x 4.125
1368759 2 DB|| 3 7.88 3.13 3.13 114.50 51.9432.000 x 22.000 x 10.375Extra HD End 1.250 x 4.125
2174725 3 HA|| 4 9.13 18.50 254.90 115.6221.750 x 16.750 x 36.750HA Center (Cast) 1.250 x 4.1252 9.13 18.50 ...2nd Row1.250 x 4.125
2174726 2 HA|| 6 4.13 3.12 3.12 82.50 37.4231.875 x 16.750 x 10.500HA End (Cast) 1.250 x 4.1253 4.13 3.13 3.13 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 61©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2174725TP 3 DB|| 4 9.13 18.50 91.27 41.4021.250 x 13.515 x 36.750Bolt on Top Plate Center 1.250 x 52 9.13 18.50 ...2nd Row1.250 x 5
2174726TPR 1 DB|\ 3 7.23 3.07 3.07 18.40 8.3531.250 x 13.372 x 6.000Bolt on Top Plate RH 1.250 x 5
2174726TPL 1 DB/| 3 7.23 3.07 3.07 18.40 8.3531.250 x 13.372 x 6.000Bolt on Top Plate LH 1.250 x 5
2174725N 3 HA|| 2 9.13 18.50 221.10 100.2921.875 x 12.750 x 36.750Narrow HA Center (Cast) 1.250 x 4.125
2085344 2 DB|| 3 3C/IMP Center REV 1.250 x 4.125
2085177 2 DB|| 3 7.88 3.13 3.13 102.70 46.5831.625 x 22.000 x 10.375C/IMP End REV 1.250 x 4.125
6Y3271 2 SB|| 3 9.13 18.50 18.50 280.90 127.4131.375 x 13.000 x 55.250C/IMP Center NR LH/RH 1.250 x 4.125
1230334 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR LH 1.250 x 4.125
1230335 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR RH 1.250 x 4.125
7V0910 2 DB|_| 4 1.44 20.75 96.00 43.5421.625 x 11.500 x 23.625Rear Wear Plate 0.750 x 2.52 1.44 20.75 ...2nd Row0.750 x 2.5
980 C General Purpose4V1220Serial Number:
4V1741 1 WOSB 24Base Edge For Bolt-on Edges or Teeth 733.70 332.801.750 x 12.000 x 132.875
7V8648 1 IRRCorner no holes RH
7V8647 1 IRRCorner no holes LH
4T6589 1 DB|| 8 6.25 3.25 13.38 384.10 174.2281.375 x 16.000 x 65.625Center 1.000 x 3.5
4T6590 2 DB|| 4 6.94 3.25 13.38 197.60 89.6341.375 x 16.000 x 33.750End 1.000 x 3.5
1078574 1 DB|| 8 6.25 3.25 13.38 499.80 226.7181.750 x 16.000 x 65.625HD Center 1.000 x 3.5
1078575 2 DB|| 4 6.94 3.25 13.38 257.10 116.6241.750 x 16.000 x 33.750HD End 1.000 x 3.5
TEETH 8J350 or J450 Options
9W6750 2 DB|_| 4 1.38 20.75 69.80 31.6621.375 x 10.000 x 23.500Rear Wear Plate 0.750 x 2.52 1.38 20.75 ...2nd Row0.750 x 2.5
980 C General Purpose4V2488Serial Number:
4V2482 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 607.00 275.331.500 x 11.500 x 132.875
7V8648 1 IRRCorner no holes RH
7V8647 1 IRRCorner no holes LH
4T6589 1 DB|| 8 6.25 3.25 13.38 384.10 174.2281.375 x 16.000 x 65.625Center 1.000 x 3.5
4T6590 2 DB|| 4 6.94 3.25 13.38 197.60 89.6341.375 x 16.000 x 33.750End 1.000 x 3.5
1078574 1 DB|| 8 6.25 3.25 13.38 499.80 226.7181.750 x 16.000 x 65.625HD Center 1.000 x 3.5
1078575 2 DB|| 4 6.94 3.25 13.38 257.10 116.6241.750 x 16.000 x 33.750HD End 1.000 x 3.5
TEETH 8J350 Options
7V0910 2 DB|_| 4 1.44 20.75 96.00 43.5421.625 x 11.500 x 23.625Rear Wear Plate 0.750 x 2.52 1.44 20.75 ...2nd Row0.750 x 2.5
980 C F G Corner Guard System, High Lift6W8564 9U1275 9U1287 9U1281 2Q2792 6W7800 8R6478Serial Number:
9V6574 1 WOSB 30Base Edge With Segment Holes 706.30 320.371.750 x 12.000 x 130.500
7V4188 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 718.40 325.861.750 x 12.000 x 130.500
6I8249FAB 1 IRR 2Corner 2 hole RH 46.90 21.272.500 x 10.002 x 11.750
6I8250FAB 1 IRR 2Corner 2 hole LH 46.90 21.272.500 x 10.002 x 11.750
2530066 1 IRR 2New Style 2 Hole Corner Protector RH 69.60 31.571.375 x 10.375 x 17.500
2530067 1 IRR 2New Style 2 Hole Corner Protector LH 69.60 31.571.375 x 10.375 x 17.500
1735428 1 IRR 2Old Style 2 Hole Corner Protector RH 35.80 16.241.250 x 9.250 x 14.500
1735429 1 IRR 2Old Style 2 Hole Corner Protector LH 35.80 16.241.250 x 9.250 x 14.500
7V4181 1 IRR 1Corner 1 hole RH 31.50 14.291.625 x 10.000 x 11.500
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 62©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7V4180 1 IRR 1Corner 1 hole LH 31.44 14.261.625 x 10.000 x 11.500
1U0762 2 DB|| 3 9.13 18.50 18.50 324.90 147.3731.375 x 16.000 x 55.250Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
1004047 2 DB|| 3 9.19 18.50 18.50 387.80 175.9031.625 x 16.000 x 55.375HD Center 1.250 x 4.125
1004043 2 DB|| 3 7.88 3.13 3.13 105.50 47.8531.750 x 22.000 x 10.375HD End 1.250 x 4.125
1368758 2 DB|| 3 9.13 18.50 18.50 445.80 202.2132.000 x 16.000 x 55.250Extra HD Center 1.250 x 4.125
1368759 2 DB|| 3 7.88 3.13 3.13 114.50 51.9432.000 x 22.000 x 10.375Extra HD End 1.250 x 4.125
2174725 3 HA|| 4 9.13 18.50 254.90 115.6221.750 x 16.750 x 36.750HA Center (Cast) 1.250 x 4.1252 9.13 18.50 ...2nd Row1.250 x 4.125
2174726 2 HA|| 6 4.13 3.12 3.12 82.50 37.4231.875 x 16.750 x 10.500HA End (Cast) 1.250 x 4.1253 4.13 3.13 3.13 ...2nd Row1.250 x 4.125
2174725TP 3 DB|| 4 9.13 18.50 91.27 41.4021.250 x 13.515 x 36.750Bolt on Top Plate Center 1.250 x 52 9.13 18.50 ...2nd Row1.250 x 5
2174726TPR 1 DB|\ 3 7.23 3.07 3.07 18.40 8.3531.250 x 13.372 x 6.000Bolt on Top Plate RH 1.250 x 5
2174726TPL 1 DB/| 3 7.23 3.07 3.07 18.40 8.3531.250 x 13.372 x 6.000Bolt on Top Plate LH 1.250 x 5
2174725N 3 HA|| 2 9.13 18.50 221.10 100.2921.875 x 12.750 x 36.750Narrow HA Center (Cast) 1.250 x 4.125
2085344 2 DB|| 3 3C/IMP Center REV 1.250 x 4.125
2085177 2 DB|| 3 7.88 3.13 3.13 102.70 46.5831.625 x 22.000 x 10.375C/IMP End REV 1.250 x 4.125
6Y3271 2 SB|| 3 9.13 18.50 18.50 280.90 127.4131.375 x 13.000 x 55.250C/IMP Center NR LH/RH 1.250 x 4.125
1230334 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR LH 1.250 x 4.125
1230335 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR RH 1.250 x 4.125
TEETH 8J350 or J450 Options
4T6700 7 DB|| 2 2.59 6.31 2.59 46.40 21.0521.180 x 14.170 x 11.500Segment 1.250 x 4.125
1078580 7 DB|| 2 2.59 6.31 2.59 68.90 31.2521.750 x 14.250 x 11.500HD Segment 1.250 x 4.125
1737447 7 HA|| 2 2.53 6.31 59.10 26.8121.750 x 13.750 x 11.375HA Segment (Cast) 1.250 x 4.125
9W6750 2 DB|_| 4 1.38 20.75 69.80 31.6621.375 x 10.000 x 23.500Rear Wear Plate 0.750 x 2.52 1.38 20.75 ...2nd Row0.750 x 2.5
980 F G H Corner Guard System1339562 1339563 1339654 1231410 1231408 1119736 1248199 2Q8481 2028662 2495036Serial Number:
1119770 1 WOSB 30Base Edge With Segment Holes 719.70 326.451.750 x 12.000 x 134.060
6I8249FAB 1 IRR 2Corner 2 hole RH 46.90 21.272.500 x 10.002 x 11.750
6I8250FAB 1 IRR 2Corner 2 hole LH 46.90 21.272.500 x 10.002 x 11.750
2530066 1 IRR 2New Style 2 Hole Corner Protector RH 69.60 31.571.375 x 10.375 x 17.500
2530067 1 IRR 2New Style 2 Hole Corner Protector LH 69.60 31.571.375 x 10.375 x 17.500
1735428 1 IRR 2Old Style 2 Hole Corner Protector RH 35.80 16.241.250 x 9.250 x 14.500
1735429 1 IRR 2Old Style 2 Hole Corner Protector LH 35.80 16.241.250 x 9.250 x 14.500
1358246 4 IRRSidebar Protector 24.00 10.891.125 x 5.750 x 18.188
1099212 2 DB|| 3 9.45 19.09 19.09 336.30 152.5431.375 x 16.000 x 57.087Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
1099230 2 DB|| 3 9.45 19.09 19.09 401.60 182.1631.625 x 16.000 x 57.087HD Center 1.250 x 4.125
1004043 2 DB|| 3 7.88 3.13 3.13 105.50 47.8531.750 x 22.000 x 10.375HD End 1.250 x 4.125
1099230-16 2 DB|| 3 9.45 19.09 19.09 460.90 209.062.000 x 16.000 x 57.087Extra HD Center 1.250
1368759 2 DB|| 3 7.88 3.13 3.13 114.50 51.9432.000 x 22.000 x 10.375Extra HD End 1.250 x 4.125
2174727 3 HA|| 4 9.42 19.09 261.70 118.7121.750 x 16.750 x 37.938HA Center (Cast) 1.250 x 4.1252 9.42 19.09 ...2nd Row1.250 x 4.125
2174726 2 HA|| 6 4.13 3.12 3.12 82.50 37.4231.875 x 16.750 x 10.500HA End (Cast) 1.250 x 4.1253 4.13 3.13 3.13 ...2nd Row1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 63©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2174727TP 3 DB|| 4 9.42 19.09 92.59 42.0021.250 x 13.515 x 37.938Bolt on Top Plate Center 1.250 x 52 4.11 9.42 ...2nd Row1.250 x 5
2174726TPR 1 DB|\ 3 7.23 3.07 3.07 18.40 8.3531.250 x 13.372 x 6.000Bolt on Top Plate RH 1.250 x 5
2174726TPL 1 DB/| 3 7.23 3.07 3.07 18.40 8.3531.250 x 13.372 x 6.000Bolt on Top Plate LH 1.250 x 5
2174727N 3 HA|| 2 9.42 19.09 207.00 93.8921.875 x 12.750 x 37.938Narrow HA Center (Cast) 1.250 x 4.125
2085178 2 DB|| 3 9.45 19.09 19.09 361.20 163.8431.375 x 16.000 x 57.087C/IMP Center REV 1.250 x 4.125
2085177 2 DB|| 3 7.88 3.13 3.13 102.70 46.5831.625 x 22.000 x 10.375C/IMP End REV 1.250 x 4.125
1099214 2 SB|| 3 9.44 19.06 19.06 251.80 114.2131.375 x 11.250 x 57.000C/IMP Center NR LH/RH 1.250 x 4.125
1230334 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR LH 1.250 x 4.125
1230335 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR RH 1.250 x 4.125
TEETH 8J400 or J450 Options
1099019 7 DB|| 2 2.61 7.28 50.50 22.9121.180 x 14.170 x 12.500Segment 1.250 x 4.125
1358219 7 DB|| 2 2.61 7.28 75.40 34.2021.750 x 14.250 x 12.500HD Segment 1.250 x 4.125
1744115 7 HA|| 2 2.63 7.25 69.20 31.3921.750 x 14.625 x 12.500HA Segment (Cast) 1.250 x 4.125
980G1X8CP 7 DB|| 2 2.61 7.28 26.00 11.7921.000 x 8.000 x 12.500Bolt on Top Plate Center 1.250 x 4.75
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
980 G H General Purpose1943128Serial Number:
1939015 1 SB|| 18Base Edge For Bolt-on Edges Only 771.80 350.081.750 x 12.000 x 142.000
7V4181 1 IRR 1Corner 1 hole RH 31.50 14.291.625 x 10.000 x 11.500
7V4180 1 IRR 1Corner 1 hole LH 31.44 14.261.625 x 10.000 x 11.500
4T6588 3 DB|| 6 6.00 7.13 7.13 279.00 126.5561.375 x 16.000 x 47.625Center 1.000 x 3.75
980 G H Corner Guard System1943129Serial Number:
1940659 1 SB|| 22Base Edge For Bolt-on Edges Only 812.20 368.411.750 x 12.000 x 150.000
7K9309 1 IRRCorner no holes RH 50.00 22.681.750 x 10.750 x 12.500
7K9310 1 IRRCorner no holes LH 50.00 22.681.750 x 10.750 x 12.500
4T6589 2 DB|| 8 6.25 3.25 13.38 384.10 174.2281.375 x 16.000 x 65.625Center 1.000 x 3.5
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
980 B Spade Nose Rock8K0071 1V6548 2V6367Serial Number:
8V9580 1 SB\_/Spade Nose Base Edge Without Holes 1248.10 566.131.750 x 25.500 x 129.000
7K9309FAB 1 IRRCorner no holes RH for no teeth 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH for no teeth 39.60 17.961.750 x 10.758 x 12.500
3V7198 1 IRRCorner no holes RH for bottom strap teet 39.90 18.101.750 x 10.000 x 14.000
3V7197 1 IRRCorner no holes LH for bottom strap teet 39.90 18.101.750 x 10.000 x 14.000
2V6299 1 IRRCorner no holes LH/RH for flushmount te
TEETH 8J350 or J450 Options
980 C Spade Nose Rock3V7233 9V0221 4V2719 9V0222 9U1290 9U1293 9V6708Serial Number:
8V9581 1 SB\_/Spade Nose Base Edge Without Holes 1269.50 575.841.750 x 26.000 x 133.000
7K9309FAB 1 IRRCorner no holes RH for no teeth 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH for no teeth 39.60 17.961.750 x 10.758 x 12.500
3V7198 1 IRRCorner no holes RH for bottom strap teet 39.90 18.101.750 x 10.000 x 14.000
3V7197 1 IRRCorner no holes LH for bottom strap teet 39.90 18.101.750 x 10.000 x 14.000
2V6299 2 IRRCorner no holes LH/RH for flushmount te
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 64©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J350 or J450 Options
9W6750 2 DB|_| 4 1.38 20.75 69.80 31.6621.375 x 10.000 x 23.500Rear Wear Plate 0.750 x 2.52 1.38 20.75 ...2nd Row0.750 x 2.5
980 F G Spade Nose Rock2Q2827 2Q2066 2Q2067Serial Number:
9V3561 1 SB\_/ 18Spade Nose Base Edge 1203.70 545.991.750 x 25.500 x 132.750
3V7198 1 IRRCorner no holes RH for bottom strap teet 39.90 18.101.750 x 10.000 x 14.000
3V7197 1 IRRCorner no holes LH for bottom strap teet 39.90 18.101.750 x 10.000 x 14.000
7K9309FAB 1 IRRCorner no holes RH for no teeth 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH for no teeth 39.60 17.961.750 x 10.758 x 12.500
4T7141 1 DB|| 4 3.88 5.69 5.31 141.00 63.9641.375 x 16.000 x 24.438Center 1.250 x 3.75
4T7144 1 DB\\ 4 4.44 5.25 13.50 167.40 75.9341.375 x 16.000 x 32.875Center RH 1.250 x 3.75
4T7142 1 DB\\ 4 6.06 6.75 5.25 155.50 70.5341.375 x 16.000 x 30.875End RH 1.250 x 3.75
4T7145 1 DB// 4 4.44 5.25 13.50 167.40 75.9341.375 x 16.000 x 32.875Center LH 1.250 x 3.75
4T7143 1 DB// 4 6.06 6.75 5.25 155.50 70.5341.375 x 16.000 x 30.875End LH 1.250 x 3.75
1078586 1 DB|| 4 3.88 5.69 5.31 182.80 82.9241.750 x 16.000 x 24.438HD Center 1.250 x 3.75
1078589 1 DB\\ 4 4.44 5.25 13.50 218.00 98.8841.750 x 16.000 x 32.875HD Intermediate End LH 1.250 x 3.75
1078587 1 DB\\ 4 6.06 6.75 5.25 201.60 91.4441.750 x 16.000 x 30.875HD End LH 1.250 x 3.75
1078590 1 DB// 4 4.44 5.25 13.50 218.00 98.8841.750 x 16.000 x 32.875HD Intermediate End RH 1.250 x 3.75
1078588 1 DB// 4 6.06 6.75 5.25 201.60 91.4441.750 x 16.000 x 30.875HD End RH 1.250 x 3.75
4T7141FHA 1 HA|| 4 3.88 5.69 5.31 182.80 82.9241.750 x 15.000 x 24.438Half Arrow Center (Fabricated) 1.250 x 3.75
4T7144FHA 1 HA\\ 4 4.94 5.25 13.50 202.10 91.6741.750 x 15.000 x 32.625Half Arrow Center RH (Fabricated) 1.250 x 3.75
4T7142FHA 1 HA\\ 3 6.50 6.75 5.25 189.00 85.7341.750 x 15.000 x 30.625HA End RH (Fabricated) 1.250 x 3.75
4T7145FHA 1 HA// 4 3.69 5.25 13.50 201.80 91.5341.750 x 15.000 x 32.625Half Arrow Center LH (Fabricated) 1.250 x 3.75
4T7143FHA 1 HA// 3 6.50 6.75 5.25 189.00 85.7341.750 x 15.000 x 30.625HA End LH (Fabricated) 1.250 x 3.75
TEETH 8J350 or J450 Options
4T3015 1 DB|| 2 2.44 5.25 40.50 18.3721.180 x 14.170 x 10.125Segment 1.250 x 3.75
4T7139 3 DB\\ 2 5.13 5.25 5.13 48.50 22.0021.180 x 14.170 x 15.500Segment RH 1.250 x 3.75
4T7140 3 DB// 2 5.13 5.25 5.13 48.50 22.0021.180 x 14.170 x 15.500Segment LH 1.250 x 3.75
1078582 1 DB|| 2 2.44 5.25 2.44 60.30 27.3521.750 x 14.250 x 10.125HD Segment 1.250 x 3.75
1078583 3 DB\\ 2 5.13 5.25 5.13 72.00 32.6621.750 x 14.250 x 15.500HD Segment RH 1.250 x 3.75
1078584 3 DB// 2 5.13 5.25 5.13 72.00 32.6621.750 x 14.250 x 15.500HD Segment LH 1.250 x 3.75
1133140 1 HA|| 2 3.03 5.28 80.20 36.3821.750 x 18.276 x 11.339HA Segment (Cast) 1.250 x 3.75
1133141 3 HA\\ 2 3.05 5.28 94.40 42.8221.750 x 18.276 x 12.913HA Segment RH (Cast) 1.250 x 3.75
1133142 3 HA// 2 3.05 5.28 93.70 42.5021.750 x 18.276 x 12.913HA Segment LH (Cast) 1.250 x 3.75
1133140TP 1 DB|| 2 3.03 5.28 26.10 11.8421.250 x 8.000 x 11.339Bolt on Top Plate Center 1.250 x 4.75
1133141TP 3 DB\\ 2 4.80 5.28 31.40 14.2421.250 x 8.000 x 15.269Bolt on Top Plate RH 1.250 x 4.75
1133142TP 3 DB// 2 4.80 5.28 30.90 14.0221.250 x 8.000 x 15.269Bolt on Top Plate LH 1.250 x 4.75
9W6750 2 DB|_| 4 1.38 20.75 69.80 31.6621.375 x 10.000 x 23.500Rear Wear Plate 0.750 x 2.52 1.38 20.75 ...2nd Row0.750 x 2.5
980 F G Spade Nose Rock1133252 1339565 1339566 1133252 1133253 1133255Serial Number:
1231396 1 SB\_/Spade Nose Base Edge Without Holes 1252.70 568.221.750 x 25.375 x 137.500
1456979 2 IRRCorner RH/LH
1456977 2 IRR 2Corner LH/RH for 9J9600 Protector 45.20 20.501.250 x 19.228 x 10.224
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 65©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J400 or J450 Options
980 F G Spade Nose Rock1352959 1369033 1133254Serial Number:
1139942 1 SB\_/ 25Spade Nose Base Edge 1197.20 543.041.750 x 25.394 x 137.480
1456979 2 IRRCorner RH/LH
1456977 2 IRR 2Corner LH/RH for 9J9600 Protector 45.20 20.501.250 x 19.228 x 10.224
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
1099123 1 DB|| 5 2.77 6.38 3.35 143.20 64.9551.375 x 16.000 x 25.000Center 1.250 x 3.75
1099122 1 DB\\ 6 5.06 3.35 3.35 184.30 83.6061.375 x 16.000 x 36.380Center RH 1.250 x 3.75
1099121 1 DB\\ 5 5.21 6.44 3.35 147.50 66.9051.375 x 16.000 x 30.000End RH 1.250 x 3.75
1099124 1 DB// 6 5.06 3.35 3.35 184.30 83.6061.375 x 16.000 x 36.380Center LH 1.250 x 3.75
1099125 1 DB// 5 5.21 6.44 3.35 147.50 66.9051.375 x 16.000 x 30.000End LH 1.250 x 3.75
1099123FHA 1 HA|| 5 2.77 6.38 3.35 186.80 84.7351.750 x 15.000 x 25.000Half Arrow Center (Fabricated) 1.250 x 3.75
1099122FHA 1 HA\\ 6 4.26 3.35 3.35 240.50 109.0961.750 x 15.000 x 36.118Half Arrow Center RH (Fabricated) 1.250 x 3.75
1099121FHA 1 HA\\ 5 4.43 6.44 3.35 192.40 87.2751.750 x 15.000 x 29.760HA End RH (Fabricated) 1.250 x 3.75
1099124FHA 1 HA// 6 5.59 3.35 3.35 240.50 109.0961.750 x 15.000 x 36.118Half Arrow Center LH (Fabricated) 1.250 x 3.75
1099125FHA 1 HA// 5 5.75 6.44 3.35 192.40 87.2751.750 x 15.000 x 29.760HA End LH (Fabricated) 1.250 x 3.75
TEETH 8J400 Options
1258404 2 ADPJ400 Weld-On Center Adapter 37.20 16.875.689 x 4.882 x 16.366
1258405 3 ADPJ400 Weld-On RH Adapter 37.20 16.875.689 x 4.882 x 16.366
1258406 3 ADPJ400 Weld-On LH Adapter 37.20 16.875.689 x 4.882 x 16.366
9W5734 1 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Segment 1.250 x 3.75
9W5737 3 DB\\ 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment RH 1.250 x 3.75
9W5730 3 DB// 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment LH 1.250 x 3.75
1073490 1 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Segment 1.250 x 3.75
1073491 3 DB\\ 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment RH 1.250 x 3.75
1073492 3 DB// 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment LH 1.250 x 3.75
1167460 1 HA|| 3 2.80 3.35 3.35 86.64 39.3032.000 x 18.827 x 12.283HA Segment (Cast) 1.250 x 3.75
1167461 3 HA\\ 3 3.35 3.35 89.95 40.8032.000 x 18.827 x 12.283HA Segment RH (Cast) 1.250 x 3.75
1167462 3 HA// 3 3.35 3.35 90.61 41.1032.000 x 18.827 x 12.283HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1386470 1 DB|| 3 2.80 3.35 3.35 82.00 37.1931.375 x 18.996 x 12.283C/IMP Segment REV 1.250 x 3.75
1386471 3 DB\\ 3 5.57 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment RH REV 1.250 x 3.75
1386472 3 DB// 3 5.53 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment LH REV 1.250 x 3.75
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
980 G Spade Nose Rock1357417Serial Number:
1341748 1 SB\_/ 27Spade Nose Base Edge 1380.10 626.002.000 x 25.390 x 137.480
1456977 2 IRR 2Corner LH/RH for 9J9600 Protector 45.20 20.501.250 x 19.228 x 10.224
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
TEETH 8J450 Options
1140464 2 ADPJ460 Weld-On Center Adapter 41.70 18.915.835 x 4.850 x 17.016
1140465 3 ADPJ460 Weld-On RH Adapter 41.70 18.915.835 x 4.850 x 17.016
1140466 3 ADPJ460 Weld-On LH Adapter 41.70 18.915.835 x 4.850 x 17.016
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 66©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W5734 1 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Segment 1.250 x 3.75
9W5737 3 DB\\ 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment RH 1.250 x 3.75
9W5730 3 DB// 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment LH 1.250 x 3.75
1073490 1 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Segment 1.250 x 3.75
1073491 3 DB\\ 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment RH 1.250 x 3.75
1073492 3 DB// 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment LH 1.250 x 3.75
1167460 1 HA|| 3 2.80 3.35 3.35 86.64 39.3032.000 x 18.827 x 12.283HA Segment (Cast) 1.250 x 3.75
1167461 3 HA\\ 3 3.35 3.35 89.95 40.8032.000 x 18.827 x 12.283HA Segment RH (Cast) 1.250 x 3.75
1167462 3 HA// 3 3.35 3.35 90.61 41.1032.000 x 18.827 x 12.283HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1386470 1 DB|| 3 2.80 3.35 3.35 82.00 37.1931.375 x 18.996 x 12.283C/IMP Segment REV 1.250 x 3.75
1386471 3 DB\\ 3 5.57 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment RH REV 1.250 x 3.75
1386472 3 DB// 3 5.53 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment LH REV 1.250 x 3.75
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
4T2986 2 DB|> 5 2.88 6.00 6.00 77.50 35.1531.000 x 10.000 x 30.625Base Edge Wear Plate 1.000 x 3.5
980 G H Straight Rock136223 2618708Serial Number:
1360878 1 WOSBBase Edge Without Holes 708.80 321.511.750 x 12.000 x 137.500
1399576 2 IRRCorner RH/LH
TEETH 8J400 Options
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
980 G Heavy Duty Quarry Spade Nose1341746 - 5.5YD BUCKETSerial Number:
1341748 1 SB\_/ 27Spade Nose Base Edge 1380.10 626.002.000 x 25.390 x 137.480
1341753 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
TEETH 8J450 Options
9W5734 1 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Segment 1.250 x 3.75
9W5737 3 DB\\ 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment RH 1.250 x 3.75
9W5730 3 DB// 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment LH 1.250 x 3.75
1073490 1 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Segment 1.250 x 3.75
1073491 3 DB\\ 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment RH 1.250 x 3.75
1073492 3 DB// 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment LH 1.250 x 3.75
1167460 1 HA|| 3 2.80 3.35 3.35 86.64 39.3032.000 x 18.827 x 12.283HA Segment (Cast) 1.250 x 3.75
1167461 3 HA\\ 3 3.35 3.35 89.95 40.8032.000 x 18.827 x 12.283HA Segment RH (Cast) 1.250 x 3.75
1167462 3 HA// 3 3.35 3.35 90.61 41.1032.000 x 18.827 x 12.283HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1386470 1 DB|| 3 2.80 3.35 3.35 82.00 37.1931.375 x 18.996 x 12.283C/IMP Segment REV 1.250 x 3.75
1386471 3 DB\\ 3 5.57 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment RH REV 1.250 x 3.75
1386472 3 DB// 3 5.53 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment LH REV 1.250 x 3.75
980 G Heavy Duty Quarry Straight1357113 - 5.75YD BUCKETSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 67©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1357115 1 WOSBBase Edge With Segment Holes 850.00 385.552.000 x 11.000 x 140.472
1341753 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
TEETH 8J450 Options
9W5734 7 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Segment 1.250 x 3.75
1073490 7 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Segment 1.250 x 3.75
1167460 7 HA|| 3 2.80 3.35 3.35 86.64 39.3032.000 x 18.827 x 12.283HA Segment (Cast) 1.250 x 3.75
1386470 7 DB|| 3 2.80 3.35 3.35 82.00 37.1931.375 x 18.996 x 12.283C/IMP Segment REV 1.250 x 3.75
1957180CAST 7 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
980 H Straight Rock2618708Serial Number:
1360878 1 WOSBBase Edge Without Holes 708.80 321.511.750 x 12.000 x 137.500
1073404 8 ADPJ400 Weld-On Center Adapter 43.00 19.50
2297104 8 TOOTH
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
980 H Straight Rock2601386Serial Number:
2601384 1
2297110 2 TOOTH
2322114 6 TOOTH
4V1616 2 SE/_\Weld-On Bucket Wear Plate
1341756 4 SE|\Weld-On Behind Heel Wear Plate
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
980 H Spade Nose Rock2601387Serial Number:
1341748 1 SB\_/ 27Spade Nose Base Edge 1380.10 626.002.000 x 25.390 x 137.480
1140464 2 ADPJ460 Weld-On Center Adapter 41.70 18.915.835 x 4.850 x 17.016
1140465 2 ADPJ460 Weld-On RH Adapter 41.70 18.915.835 x 4.850 x 17.016
1140466 2 ADPJ460 Weld-On LH Adapter 41.70 18.915.835 x 4.850 x 17.016
1167465 1J460 Weld-On RH Adapter HDLL
1167466 1J460 Weld-On LH Adapter HDLL
9W5734 1 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Segment 1.250 x 3.75
9W5737 3 DB\\ 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment RH 1.250 x 3.75
9W5730 3 DB// 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment LH 1.250 x 3.75
1073490 1 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Segment 1.250 x 3.75
1073491 3 DB\\ 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment RH 1.250 x 3.75
1073492 3 DB// 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment LH 1.250 x 3.75
1167460 1 HA|| 3 2.80 3.35 3.35 86.64 39.3032.000 x 18.827 x 12.283HA Segment (Cast) 1.250 x 3.75
1167461 3 HA\\ 3 3.35 3.35 89.95 40.8032.000 x 18.827 x 12.283HA Segment RH (Cast) 1.250 x 3.75
1167462 3 HA// 3 3.35 3.35 90.61 41.1032.000 x 18.827 x 12.283HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 68©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1386470 1 DB|| 3 2.80 3.35 3.35 82.00 37.1931.375 x 18.996 x 12.283C/IMP Segment REV 1.250 x 3.75
1386471 3 DB\\ 3 5.57 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment RH REV 1.250 x 3.75
1386472 3 DB// 3 5.53 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment LH REV 1.250 x 3.75
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
4T2986 2 DB|> 5 2.88 6.00 6.00 77.50 35.1531.000 x 10.000 x 30.625Base Edge Wear Plate 1.000 x 3.5
4V1616 2 SE/_\Weld-On Bucket Wear Plate
1341756 4 SE|\Weld-On Behind Heel Wear Plate
980 H Spade Nose Rock2618709Serial Number:
1231396 1 SB\_/Spade Nose Base Edge Without Holes 1252.70 568.221.750 x 25.375 x 137.500
1258404 2 ADPJ400 Weld-On Center Adapter 37.20 16.875.689 x 4.882 x 16.366
1258405 3 ADPJ400 Weld-On RH Adapter 37.20 16.875.689 x 4.882 x 16.366
1258406 3 ADPJ400 Weld-On LH Adapter 37.20 16.875.689 x 4.882 x 16.366
2238104 2 TOOTH
2238105 3 TOOTH
2238106 3 TOOTH
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
4V1616 2 SE/_\Weld-On Bucket Wear Plate
980 H Spade Nose Rock2618711 2618712Serial Number:
1139942 1 SB\_/ 25Spade Nose Base Edge 1197.20 543.041.750 x 25.394 x 137.480
1099123 1 DB|| 5 2.77 6.38 3.35 143.20 64.9551.375 x 16.000 x 25.000Center 1.250 x 3.75
1099122 1 DB\\ 6 5.06 3.35 3.35 184.30 83.6061.375 x 16.000 x 36.380Center RH 1.250 x 3.75
1099121 1 DB\\ 5 5.21 6.44 3.35 147.50 66.9051.375 x 16.000 x 30.000End RH 1.250 x 3.75
1099124 1 DB// 6 5.06 3.35 3.35 184.30 83.6061.375 x 16.000 x 36.380Center LH 1.250 x 3.75
1099125 1 DB// 5 5.21 6.44 3.35 147.50 66.9051.375 x 16.000 x 30.000End LH 1.250 x 3.75
1099123FHA 1 HA|| 5 2.77 6.38 3.35 186.80 84.7351.750 x 15.000 x 25.000Half Arrow Center (Fabricated) 1.250 x 3.75
1099122FHA 1 HA\\ 6 4.26 3.35 3.35 240.50 109.0961.750 x 15.000 x 36.118Half Arrow Center RH (Fabricated) 1.250 x 3.75
1099121FHA 1 HA\\ 5 4.43 6.44 3.35 192.40 87.2751.750 x 15.000 x 29.760HA End RH (Fabricated) 1.250 x 3.75
1099124FHA 1 HA// 6 5.59 3.35 3.35 240.50 109.0961.750 x 15.000 x 36.118Half Arrow Center LH (Fabricated) 1.250 x 3.75
1099125FHA 1 HA// 5 5.75 6.44 3.35 192.40 87.2751.750 x 15.000 x 29.760HA End LH (Fabricated) 1.250 x 3.75
1258404 2 ADPJ400 Weld-On Center Adapter 37.20 16.875.689 x 4.882 x 16.366
1258405 3 ADPJ400 Weld-On RH Adapter 37.20 16.875.689 x 4.882 x 16.366
1258406 3 ADPJ400 Weld-On LH Adapter 37.20 16.875.689 x 4.882 x 16.366
9W5734 1 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Segment 1.250 x 3.75
9W5737 3 DB\\ 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment RH 1.250 x 3.75
9W5730 3 DB// 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment LH 1.250 x 3.75
1073490 1 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Segment 1.250 x 3.75
1073491 3 DB\\ 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment RH 1.250 x 3.75
1073492 3 DB// 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment LH 1.250 x 3.75
1167460 1 HA|| 3 2.80 3.35 3.35 86.64 39.3032.000 x 18.827 x 12.283HA Segment (Cast) 1.250 x 3.75
1167461 3 HA\\ 3 3.35 3.35 89.95 40.8032.000 x 18.827 x 12.283HA Segment RH (Cast) 1.250 x 3.75
1167462 3 HA// 3 3.35 3.35 90.61 41.1032.000 x 18.827 x 12.283HA Segment LH (Cast) 1.250 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 69©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1386470 1 DB|| 3 2.80 3.35 3.35 82.00 37.1931.375 x 18.996 x 12.283C/IMP Segment REV 1.250 x 3.75
1386471 3 DB\\ 3 5.57 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment RH REV 1.250 x 3.75
1386472 3 DB// 3 5.53 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment LH REV 1.250 x 3.75
1099215 2 DB|| 4 2.00 20.50 71.90 32.6121.375 x 10.000 x 24.500Rear Wear Plate 0.750 x 2.52 2.00 20.50 ...2nd Row0.750 x 2.5
4V1616 2 SE/_\Weld-On Bucket Wear Plate
983 General Purpose9V4619 8K5118 8K5121Serial Number:
8K5000 1 WOSBBase Edge Without Holes 654.00 296.651.750 x 12.000 x 120.750
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
TEETH 6J450 Options
983 General Purpose8K5119 8K5120 9K4618Serial Number:
8K5056 1 WOSBBase Edge Without Holes 727.70 330.081.750 x 12.000 x 128.750
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
TEETH 6J450 Options
983 Spade Nose Rock3V4194Serial Number:
9V0237 1 WOSBBase Edge Without Holes 839.40 380.752.000 x 13.000 x 122.000
3V3311 1 IRRCorner no holes RH
3V3310 1 IRRCorner no holes LH
TEETH 8J450 Options
983 Spade Nose Rock9K6024Serial Number:
9V4650 1 SB\_/Spade Nose Base Edge Without Holes 1355.00 614.622.000 x 22.750 x 128.375
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
TEETH 6J450 Options
983 Spade Nose Rock3V3342Serial Number:
8V9591 1 SB\_/Spade Nose Base Edge Without Holes 1415.00 641.832.000 x 22.750 x 129.000
3V3311 1 IRRCorner no holes RH
3V3310 1 IRRCorner no holes LH
TEETH 8J450 Options
983 Spade Nose Rock3V4193Serial Number:
9V0235 1 WOSBBase Edge Without Holes 852.00 386.462.000 x 13.000 x 129.500
3V3311 1 IRRCorner no holes RH
3V3310 1 IRRCorner no holes LH
TEETH 8J450 Options
983 Slag7K2906Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 70©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7K2736 1 WOSBBase Edge Without Holes 1270.70 576.382.000 x 20.000 x 118.000
7K2724 2 IRRCorner RH/LH
983 Slag4V5288Serial Number:
9V1306 1 WOSBBase Edge Without Holes 1708.00 774.742.500 x 21.250 x 119.500
TEETH 6J550 Options
983 Demolition7K3916 7K8710 7K3195Serial Number:
7K2326 1 WOSBBase Edge Without Holes 570.00 258.551.750 x 12.000 x 126.000
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
4T8376 1 DB|| 30 30Multi purpose dozer center 0.625 x 2.25
TEETH 6J450 Options
988 General Purpose8K6590Serial Number:
8K6588 1 WOSBBase Edge 623.00 282.591.750 x 12.000 x 110.250
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
TEETH 7J350 Options
988 General Purpose8K6540 8K6550 8K6572 9K2374 9K3715 9K8919 9K9170Serial Number:
8K5056 1 WOSBBase Edge Without Holes 727.70 330.081.750 x 12.000 x 128.750
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
TEETH 8J450 Options
988 B Corner Guard System6W7804Serial Number:
4E6085 1 WOSB 30Base Edge With Segment Holes 768.70 348.681.750 x 12.000 x 140.160
6W9311 1 SB|| 18Base Edge Without Segment Holes 767.00 347.911.750 x 12.000 x 140.160
7V4181 1 IRR 1Corner 1 hole RH 31.50 14.291.625 x 10.000 x 11.500
7V4180 1 IRR 1Corner 1 hole LH 31.44 14.261.625 x 10.000 x 11.500
9W1375 2 DB|| 3 9.88 20.13 20.13 353.10 160.1621.375 x 16.000 x 60.000Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
9W1375-13 2 DB|| 3 9.88 20.13 20.13 422.30 191.5521.625 x 16.000 x 60.000HD Center 1.250 x 4.125
1004043 2 DB|| 3 7.88 3.13 3.13 105.50 47.8521.750 x 22.000 x 10.375HD End 1.250 x 4.125
9W1375HAN 3 HA|| 2 9.88 20.13 227.10 103.0131.875 x 12.750 x 39.875Narrow HA Center (Cast) 1.250 x 4.125
2174726 2 HA|| 6 4.13 3.12 3.12 82.50 37.4221.875 x 16.750 x 10.500HA End (Cast) 1.250 x 4.1253 4.13 3.13 3.13 ...2nd Row1.250 x 4.125
1092697 2 SB|| 3 9.88 20.13 20.133C/IMP Center NR LH/RH 1.250 x 4.125
1230334 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR LH 1.250 x 4.125
1230335 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR RH 1.250 x 4.125
2085177 2 DB|| 3 7.88 3.13 3.13 102.70 46.5831.625 x 22.000 x 10.375C/IMP End REV 1.250 x 4.125
TEETH 8J450 Options
4T6700 7 DB|| 2 2.59 6.31 2.59 46.40 21.0521.180 x 14.170 x 11.500Segment 1.250 x 4.125
1078580 7 DB|| 2 2.59 6.31 2.59 68.90 31.2521.750 x 14.250 x 11.500HD Segment 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 71©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1737447 7 HA|| 2 2.53 6.31 59.10 26.8121.750 x 13.750 x 11.375HA Segment (Cast) 1.250 x 4.125
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
988 B General Purpose3V0200 9V1345Serial Number:
3V0187 1 WOSB 18Base Edge For Bolt-on Edges or Teeth 798.50 362.191.750 x 12.000 x 143.500
4E5873 2 IRRCorner LH/RH for 9J9600 Protector
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
4T6588 3 DB|| 6 6.00 7.13 7.13 279.00 126.5561.375 x 16.000 x 47.625Center 1.000 x 3.25
4T6588-13 3 DB|| 6 6.00 7.13 7.13 333.30 151.1861.625 x 16.000 x 47.625HD Center 1.000 x 3.25
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
988 F Corner Guard System9U3744 1456499Serial Number:
9U3748 1 WOSB 30Base Edge With Segment Holes 788.30 357.571.750 x 12.000 x 145.188
7V4181 1 IRR 1Corner 1 hole RH 31.50 14.291.625 x 10.000 x 11.500
7V4180 1 IRR 1Corner 1 hole LH 31.44 14.261.625 x 10.000 x 11.500
1045841 2 DB|| 3 11.13 20.56 20.56 367.00 166.4731.375 x 16.000 x 62.375Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
1835325 2 DB|| 3 11.25 20.56 20.56 439.00 199.1331.625 x 16.000 x 62.375HD Center 1.250 x 4.125
1004043 2 DB|| 3 7.88 3.13 3.13 105.50 47.8531.750 x 22.000 x 10.375HD End 1.250 x 4.125
1045841-16 2 DB|| 3 11.13 20.56 20.56 486.00 220.4532.000 x 16.000 x 62.375Extra HD Center 1.250 x 4.125
1368759 2 DB|| 3 7.88 3.13 3.13 114.50 51.9432.000 x 22.000 x 10.375Extra HD End 1.250 x 4.125
1045841HAC 1 HA|| 4 9.13 20.56 276.20 125.2821.750 x 16.750 x 38.827Half Arrow Center (Cast) 1.250 x 4.1252 9.13 20.56 ...2nd Row1.250 x 4.125
1045841HALR 2 HA|| 4 11.18 20.56 286.20 129.8221.750 x 16.750 x 42.925Half Arrow Center LH/RH (Cast) 1.250 x 4.1252 11.18 20.56 ...2nd Row1.250 x 4.125
2174726 2 HA|| 6 4.13 3.12 3.12 82.50 37.4231.875 x 16.750 x 10.500HA End (Cast) 1.250 x 4.1254.13 3.13 3.13 ...2nd Row1.250 x 0
2085342 2 DB|| 3 3C/IMP Center REV 1.250 x 4.125
2085177 2 DB|| 3 7.88 3.13 3.13 102.70 46.5831.625 x 22.000 x 10.375C/IMP End REV 1.250 x 4.125
1321069 1 SB|| 3 11.13 20.56 20.56 260.00 117.9331.375 x 11.000 x 62.375C/IMP Center NR RH 1.250 x 4.125
1321070 1 SB|| 3 11.13 20.56 20.56 260.00 117.9331.375 x 11.000 x 62.375C/IMP Center NR LH 1.250 x 4.125
1230334 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR LH 1.250 x 4.125
1230335 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR RH 1.250 x 4.125
TEETH 8J450 Options
1386540 7 DB|| 2 2.56 9.50 2.56 69.10 31.3421.375 x 13.000 x 14.625Segment 1.250 x 4.125
1835324 7 DB|| 2 2.56 9.50 81.90 37.1521.625 x 13.000 x 14.625HD Segment 1.250 x 4.125
1386540FHAY 7 HA|| 2 2.56 9.50 121.00 54.882.000 x 15.000 x 14.625HA Segment (Fabricated) 1.250
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 72©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
988 G Corner Guard System1751457Serial Number:
1835190 1 WOSB 30Base Edge With Segment Holes 954.30 432.862.000 x 12.800 x 145.188
6I8249FAB 1 IRR 2Corner 2 hole RH 46.90 21.272.500 x 10.002 x 11.750
6I8250FAB 1 IRR 2Corner 2 hole LH 46.90 21.272.500 x 10.002 x 11.750
2530066 1 IRR 2New Style 2 Hole Corner Protector RH 69.60 31.571.375 x 10.375 x 17.500
2530067 1 IRR 2New Style 2 Hole Corner Protector LH 69.60 31.571.375 x 10.375 x 17.500
1735428 1 IRR 2Old Style 2 Hole Corner Protector RH 35.80 16.241.250 x 9.250 x 14.500
1735429 1 IRR 2Old Style 2 Hole Corner Protector LH 35.80 16.241.250 x 9.250 x 14.500
1045841 2 DB|| 3 11.13 20.56 20.56 367.00 166.4731.375 x 16.000 x 62.375Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
1835325 2 DB|| 3 11.25 20.56 20.56 439.00 199.1331.625 x 16.000 x 62.375HD Center 1.250 x 4.125
1004043 2 DB|| 3 7.88 3.13 3.13 105.50 47.8531.750 x 22.000 x 10.375HD End 1.250 x 4.125
1045841-16 2 DB|| 3 11.13 20.56 20.56 486.00 220.4532.000 x 16.000 x 62.375Extra HD Center 1.250 x 4.125
1368759 2 DB|| 3 7.88 3.13 3.13 114.50 51.9432.000 x 22.000 x 10.375Extra HD End 1.250 x 4.125
1045841HAC 1 HA|| 4 9.13 20.56 276.20 125.2821.750 x 16.750 x 38.827Half Arrow Center (Cast) 1.250 x 4.1252 9.13 20.56 ...2nd Row1.250 x 4.125
1045841HALR 2 HA|| 4 11.18 20.56 286.20 129.8221.750 x 16.750 x 42.925Half Arrow Center LH/RH (Cast) 1.250 x 4.1252 11.18 20.56 ...2nd Row1.250 x 4.125
2174726 2 HA|| 6 4.13 3.12 3.12 82.50 37.4231.875 x 16.750 x 10.500HA End (Cast) 1.250 x 4.1254.13 3.13 3.13 ...2nd Row1.250 x 0
2085342 2 DB|| 3 3C/IMP Center REV 1.250 x 4.125
2085177 2 DB|| 3 7.88 3.13 3.13 102.70 46.5831.625 x 22.000 x 10.375C/IMP End REV 1.250 x 4.125
1321069 1 SB|| 3 11.13 20.56 20.56 260.00 117.9331.375 x 11.000 x 62.375C/IMP Center NR RH 1.250 x 4.125
1321070 1 SB|| 3 11.13 20.56 20.56 260.00 117.9331.375 x 11.000 x 62.375C/IMP Center NR LH 1.250 x 4.125
1230334 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR LH 1.250 x 4.125
1230335 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR RH 1.250 x 4.125
TEETH 8J450 Options
1386540 7 DB|| 2 2.56 9.50 2.56 69.10 31.3421.375 x 13.000 x 14.625Segment 1.250 x 4.125
1835324 7 DB|| 2 2.56 9.50 81.90 37.1521.625 x 13.000 x 14.625HD Segment 1.250 x 4.125
1386540FHAY 7 HA|| 2 2.56 9.50 121.00 54.882.000 x 15.000 x 14.625HA Segment (Fabricated) 1.250
1909793 2 DB||Rear Wear Plate
1909794 2 DB||Heavy Duty Wear Plate
1366205 2 IRR 34.40 15.601.000 x 10.750 x 16.250Weld-On Wear Plate
988 H Corner Guard System2462753Serial Number:
2573667 1 SB|| 30Base Edge With Segment Holes 1205.30 546.712.000 x 15.748 x 145.472
6I8249FAB 1 IRR 2Corner 2 hole RH 46.90 21.272.500 x 10.002 x 11.750
6I8250FAB 1 IRR 2Corner 2 hole LH 46.90 21.272.500 x 10.002 x 11.750
2530066 1 IRR 2New Style 2 Hole Corner Protector RH 69.60 31.571.375 x 10.375 x 17.500
2530067 1 IRR 2New Style 2 Hole Corner Protector LH 69.60 31.571.375 x 10.375 x 17.500
1735428 1 IRR 2Old Style 2 Hole Corner Protector RH 35.80 16.241.250 x 9.250 x 14.500
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 73©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1735429 1 IRR 2Old Style 2 Hole Corner Protector LH 35.80 16.241.250 x 9.250 x 14.500
1045841 2 DB|| 3 11.13 20.56 20.56 367.00 166.4731.375 x 16.000 x 62.375Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
1835325 2 DB|| 3 11.25 20.56 20.56 439.00 199.1331.625 x 16.000 x 62.375HD Center 1.250 x 4.125
1004043 2 DB|| 3 7.88 3.13 3.13 105.50 47.8531.750 x 22.000 x 10.375HD End 1.250 x 4.125
1045841-16 2 DB|| 3 11.13 20.56 20.56 486.00 220.4532.000 x 16.000 x 62.375Extra HD Center 1.250 x 4.125
1368759 2 DB|| 3 7.88 3.13 3.13 114.50 51.9432.000 x 22.000 x 10.375Extra HD End 1.250 x 4.125
1045841HAC 1 HA|| 4 9.13 20.56 276.20 125.2821.750 x 16.750 x 38.827Half Arrow Center (Cast) 1.250 x 4.1252 9.13 20.56 ...2nd Row1.250 x 4.125
1045841HALR 2 HA|| 4 11.18 20.56 286.20 129.8221.750 x 16.750 x 42.925Half Arrow Center LH/RH (Cast) 1.250 x 4.1252 11.18 20.56 ...2nd Row1.250 x 4.125
2174726 2 HA|| 6 4.13 3.12 3.12 82.50 37.4231.875 x 16.750 x 10.500HA End (Cast) 1.250 x 4.1254.13 3.13 3.13 ...2nd Row1.250 x 0
2085342 2 DB|| 3 3C/IMP Center REV 1.250 x 4.125
2085177 2 DB|| 3 7.88 3.13 3.13 102.70 46.5831.625 x 22.000 x 10.375C/IMP End REV 1.250 x 4.125
1321069 1 SB|| 3 11.13 20.56 20.56 260.00 117.9331.375 x 11.000 x 62.375C/IMP Center NR RH 1.250 x 4.125
1321070 1 SB|| 3 11.13 20.56 20.56 260.00 117.9331.375 x 11.000 x 62.375C/IMP Center NR LH 1.250 x 4.125
1230334 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR LH 1.250 x 4.125
1230335 1 SB|| 3 8.25 3.13 3.13 67.10 30.4431.375 x 16.500 x 10.375C/IMP Center NR RH 1.250 x 4.125
TEETH 8J450 Options
1386540 7 DB|| 2 2.56 9.50 2.56 69.10 31.3421.375 x 13.000 x 14.625Segment 1.250 x 4.125
1835324 7 DB|| 2 2.56 9.50 81.90 37.1521.625 x 13.000 x 14.625HD Segment 1.250 x 4.125
1386540FHAY 7 HA|| 2 2.56 9.50 121.00 54.882.000 x 15.000 x 14.625HA Segment (Fabricated) 1.250
988 H Corner Guard System2658219Serial Number:
2508402 1 SB|| 30Base Edge With Segment Holes 1250.90 567.402.000 x 15.748 x 150.850
6I8249FAB 1 IRR 2Corner 2 hole RH 46.90 21.272.500 x 10.002 x 11.750
6I8250FAB 1 IRR 2Corner 2 hole LH 46.90 21.272.500 x 10.002 x 11.750
2530066 1 IRR 2New Style 2 Hole Corner Protector RH 69.60 31.571.375 x 10.375 x 17.500
2530067 1 IRR 2New Style 2 Hole Corner Protector LH 69.60 31.571.375 x 10.375 x 17.500
1735428 1 IRR 2Old Style 2 Hole Corner Protector RH 35.80 16.241.250 x 9.250 x 14.500
1735429 1 IRR 2Old Style 2 Hole Corner Protector LH 35.80 16.241.250 x 9.250 x 14.500
2085261 2 DB|| 3 12.00 21.50 21.50 462.10 209.6131.625 x 16.000 x 65.625Center 1.250 x 4.125
1U0761 2 DB|| 3 7.88 3.13 3.13 94.89 43.0431.625 x 22.000 x 10.375End 1.250 x 4.125
2085261FHAL 1 HA|| 3 10.63 21.50 21.50 440.00 199.5831.750 x 13.000 x 65.625Half Arrow Center LH (Fabricated) 1.250 x 4.125
2085261FHAR 1 HA|| 3 10.63 21.50 21.50 440.00 199.5831.750 x 13.000 x 65.625Half Arrow Center RH (Fabricated) 1.250 x 4.125
1U0761FHA 2 HA|| 6 3.63 3.13 93.00 42.1831.750 x 19.000 x 10.375HA End (Fabricated) 1.250 x 4.1253.63 3.13 ...2nd Row1.250 x 0
988 Spade Nose Rock8K6183 8K6184 2V6382Serial Number:
8V9583 1 SB\_/Spade Nose Base Edge Without Holes 1573.90 713.912.000 x 27.500 x 134.375
7K9309FAB 1 IRRCorner no holes RH for no teeth 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH for no teeth 39.60 17.961.750 x 10.758 x 12.500
6W9414 2 IRRCorner no holes LH/RH for flushmount te
TEETH 8J450 or J550 Options
988 B Spade Nose Rock9V1340 5V1221 4E0068 9V0216 9V1340 9V1341 4E0070 2Q4431Serial Number:
8V9585 1 SB\_/Spade Nose Base Edge Without Holes 1672.40 758.592.000 x 27.750 x 143.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 74©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4E6474 2 IRR 3Corner LH/RH for 9J9600 Protector 116.40 52.801.250 x 11.063 x 59.125
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
7K9309FAB 1 IRRCorner no holes RH for no teeth 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH for no teeth 39.60 17.961.750 x 10.758 x 12.500
TEETH 8J450 or J550 Options
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
988 B Spade Nose Rock9V3564 4E0062 1111509 1456496 2Q3930Serial Number:
8R4649 1 SB\_/ 31Spade Nose Base Edge 1599.70 725.612.000 x 27.750 x 143.500
4E6474 2 IRR 3Corner LH/RH for 9J9600 Protector 116.40 52.801.250 x 11.063 x 59.125
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
9W5733 1 DB|| 5 4.17 6.38 3.35 191.10 86.6851.375 x 19.000 x 27.794Center 1.250 x 3.75
9W5736 1 DB\\ 6 4.71 3.35 3.35 214.00 97.0761.375 x 19.000 x 36.238Center RH 1.250 x 3.75
9W5735 1 DB\\ 5 6.87 6.71 3.35 198.30 89.9551.375 x 19.000 x 33.878End RH 1.250 x 3.75
9W5731 1 DB// 6 4.71 3.35 3.35 214.00 97.0761.375 x 19.000 x 36.238Center LH 1.250 x 3.75
9W5732 1 DB// 5 6.89 6.71 3.35 198.30 89.9551.375 x 19.000 x 33.878End LH 1.250 x 3.75
1061096 1 DB|| 5 4.16 6.38 3.35 233.20 105.7851.750 x 19.000 x 27.813HD Center 1.250 x 3.75
1061098 1 DB\\ 6 4.67 3.35 3.35 260.40 118.1261.750 x 19.000 x 36.188HD Intermediate End RH 1.250 x 3.75
1061097 1 DB\\ 5 6.88 6.71 3.35 240.70 109.1851.750 x 19.000 x 33.875HD End RH 1.250 x 3.75
1061094 1 DB// 6 4.67 3.35 3.35 260.40 118.1261.750 x 19.000 x 36.188HD Intermediate End LH 1.250 x 3.75
1061095 1 DB// 5 6.88 6.71 3.35 240.70 109.1851.750 x 19.000 x 33.875HD End LH 1.250 x 3.75
9W5733HA 1 HA|| 5 4.18 6.38 3.35 189.90 86.141.750 x 16.000 x 27.813Half Arrow Center (Cast) 1.250 x 3.75
9W5736HA 1 HA\\ 6 2.02 3.35 3.35 209.50 95.031.750 x 16.000 x 30.142Half Arrow Center RH (Cast) 1.250 x 3.75
9W5735HA 1 HA\\ 4 4.03 6.72 3.35 192.60 87.361.750 x 16.000 x 27.847HA End RH (Cast) 1.250 x 3.75
9W5731HA 1 HA// 6 2.02 3.35 3.35 209.50 95.031.750 x 16.000 x 30.142Half Arrow Center LH (Cast) 1.250 x 3.75
9W5732HA 1 HA// 4 4.03 6.72 3.35 192.60 87.361.750 x 16.000 x 27.847HA End LH (Cast) 1.250 x 3.75
TEETH 8J450 or J550 Options
9W5734 1 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Segment 1.250 x 3.75
9W5737 3 DB\\ 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment RH 1.250 x 3.75
9W5730 3 DB// 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment LH 1.250 x 3.75
9W8367 1 DB\\ 3 6.78 3.35 3.35 100.30 45.5031.375 x 19.000 x 20.250Optional Longer End Segment RH 1.250 x 3.75
9W8368 1 DB// 3 6.78 3.35 3.35 100.30 45.5031.375 x 19.000 x 20.250Optional Longer End Segment LH 1.250 x 3.75
1073490 1 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Segment 1.250 x 3.75
1073491 3 DB\\ 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment RH 1.250 x 3.75
1073492 3 DB// 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment LH 1.250 x 3.75
1167460 1 HA|| 3 2.80 3.35 3.35 86.64 39.3032.000 x 18.827 x 12.283HA Segment (Cast) 1.250 x 3.75
1167461 3 HA\\ 3 3.35 3.35 89.95 40.8032.000 x 18.827 x 12.283HA Segment RH (Cast) 1.250 x 3.75
1167462 3 HA// 3 3.35 3.35 90.61 41.1032.000 x 18.827 x 12.283HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 75©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1386470 1 DB|| 3 2.80 3.35 3.35 82.00 37.1931.375 x 18.996 x 12.283C/IMP Segment REV 1.250 x 3.75
1386471 3 DB\\ 3 5.57 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment RH REV 1.250 x 3.75
1386472 3 DB// 3 5.53 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment LH REV 1.250 x 3.75
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1231.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3
988 B Straight Rock5V1223 9V0218 9V1343 9V6603 5V1222 9V0217 9V1342 9V6604Serial Number:
9C2932 1 WOSB 21Base Edge With Segment Holes 937.40 425.202.000 x 13.000 x 143.500
9V0232 1 WOSBBase Edge Without Holes 987.20 447.792.000 x 13.000 x 143.500
2V4314 1 IRRCorner no holes RH 28.00 12.701.500 x 11.500 x 9.375
2V4315 1 IRRCorner no holes LH 28.00 12.701.500 x 11.500 x 9.375
7K9309FAB 1 IRRCorner no holes RH for no teeth 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH for no teeth 39.60 17.961.750 x 10.758 x 12.500
9W8250 1 DB|| 3 5.81 23.02 23.02 387.30 175.6831.375 x 19.000 x 57.650Center 1.250 x 3.75
9W8249 2 DB|| 4 10.24 3.35 16.32 290.20 131.6341.375 x 19.000 x 43.500End 1.250 x 3.75
9W8250-13 1 DB|| 3 5.81 22.94 22.94 459.20 208.2931.625 x 19.000 x 57.625HD Center 1.250 x 3.75
9W8249-13 2 DB|| 4 10.25 3.31 16.31 343.70 155.9041.625 x 19.000 x 43.500HD End 1.250 x 3.75
TEETH 8J450 or J550 Options
9W5734 7 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Segment 1.250 x 3.75
1073490 7 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Segment 1.250 x 3.75
1167460 7 HA|| 3 2.80 3.35 3.35 86.64 39.3032.000 x 18.827 x 12.283HA Segment (Cast) 1.250 x 3.75
1957180CAST 7 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1386470 7 DB|| 3 2.80 3.35 3.35 82.00 37.1931.375 x 18.996 x 12.283C/IMP Segment REV 1.250 x 3.75
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
988 F Spade Nose Rock9U4191 1456506 9U4719 145600 4E6470 1069821 9U4185 9U4189 9U4181Serial Number:
4E7616 1 SB\_/ 27Spade Nose Base Edge 1606.90 728.882.000 x 25.787 x 148.504
9U4713 1 SB\_/Spade Nose Base Edge Without Holes 1741.50 789.932.000 x 28.500 x 148.500
4E6474 2 IRR 3Corner LH/RH for 9J9600 Protector 116.40 52.801.250 x 11.063 x 59.125
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
1019350 1 DB|| 9 2.45 3.35 3.35 374.20 169.7391.500 x 19.000 x 52.375Center 1.250 x 3.75
1019351 1 DB\\ 6 14.10 3.35 3.35 368.60 167.1961.500 x 19.000 x 56.000End RH 1.250 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 76©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1019352 1 DB// 6 14.10 3.35 3.35 368.60 167.1961.500 x 19.000 x 56.000End LH 1.250 x 3.75
1073540 1 DB|| 9 2.48 3.35 3.35 520.80 236.2392.000 x 19.000 x 52.438HD Center 1.250 x 3.75
1073543 1 DB\\ 6 14.10 3.35 3.35 511.60 232.0662.000 x 19.000 x 56.000HD End LH 1.250 x 3.75
1073544 1 DB// 6 14.10 3.35 3.35 511.60 232.0662.000 x 19.000 x 56.000HD End RH 1.250 x 3.75
1019350FHA 1 HA|| 9 2.25 3.35 3.35 349.50 158.5391.750 x 13.500 x 51.979Half Arrow Center (Fabricated) 1.250 x 3.75
1019351FHA 1 HA\\ 6 14.66 3.35 3.35 343.40 155.7661.750 x 13.500 x 54.000HA End RH (Fabricated) 1.250 x 3.75
1019352FHA 1 HA// 6 14.66 3.35 3.35 343.40 155.7661.750 x 13.500 x 54.000HA End LH (Fabricated) 1.250 x 3.75
1366790 1 9 2.38 3.38 3.389C/IMP Center NR 1.250 x 3.75
1366793 1 6 14.00 3.38 3.386C/IMP Center NR RH 1.250 x 3.75
1366794 1 6 14.00 3.38 3.386C/IMP Center NR LH 1.250 x 3.75
TEETH 8J450 or J550 Options
1019435 3 DB|| 3 3.47 3.35 3.35 98.90 44.8631.500 x 19.000 x 13.625Segment 1.250 x 3.75
1019436 2 DB\\ 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment RH 1.250 x 3.75
1019437 2 DB// 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment LH 1.250 x 3.75
1073536 3 DB|| 3 3.47 3.35 3.35 113.90 51.6631.750 x 19.000 x 13.625HD Segment 1.250 x 3.75
1073537 2 DB\\ 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment RH 1.250 x 3.75
1073538 2 DB// 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment LH 1.250 x 3.75
1099080 3 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
1099081 2 HA\\ 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment RH (Cast) 1.250 x 3.75
1099082 2 HA// 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment LH (Cast) 1.250 x 3.75
1099080HD 3 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1099081HD 2 HA\\ 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment RH (Cast) 1.250 x 3.75
1099082HD 2 HA// 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 3 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 2 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 2 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1380865 3 3 3.44 3.38 3.383C/IMP Segment REV 1.250 x 3.75
1380866 2 3 6.13 3.38 3.383C/IMP Segment RH REV 1.250 x 3.75
1380867 2 3 6.13 3.38 3.383C/IMP Segment LH REV 1.250 x 3.75
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1231.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3
7T9127 2 DB|> 5 3.69 6.00 6.00 150.20 68.1331.375 x 13.000 x 32.438Base Edge Wear Plate with HA segment 1.000 x 3
988 F Spade Nose Rock1456505 1456501Serial Number:
1330821 1 SB\_/Spade Nose Base Edge Without Holes 1743.00 790.612.000 x 28.500 x 148.500
4E6474 2 IRR 3Corner LH/RH for 9J9600 Protector 116.40 52.801.250 x 11.063 x 59.125
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
TEETH 8J450 or J550 Options
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 77©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
988 F Spade Nose Rock1450354 1456495 1456503Serial Number:
1323117 1 SB\_/ 21Spade Nose Base For Segments 2.000 x 25.790 x 148.500
4E6474 2 IRR 3Corner LH/RH for 9J9600 Protector 116.40 52.801.250 x 11.063 x 59.125
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
TEETH 8J450 or J550 Options
1019435 1 DB|| 3 3.47 3.35 3.35 98.90 44.8631.500 x 19.000 x 13.625Segment 1.250 x 3.75
1019436 3 DB\\ 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment RH 1.250 x 3.75
1019437 3 DB// 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment LH 1.250 x 3.75
1073536 1 DB|| 3 3.47 3.35 3.35 113.90 51.6631.750 x 19.000 x 13.625HD Segment 1.250 x 3.75
1073537 3 DB\\ 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment RH 1.250 x 3.75
1073538 3 DB// 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment LH 1.250 x 3.75
1099080 1 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
1099081 3 HA\\ 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment RH (Cast) 1.250 x 3.75
1099082 3 HA// 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment LH (Cast) 1.250 x 3.75
1099080HD 1 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1099081HD 3 HA\\ 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment RH (Cast) 1.250 x 3.75
1099082HD 3 HA// 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1380865 1 3 3.44 3.38 3.383C/IMP Segment REV 1.250 x 3.75
1380866 3 3 6.13 3.38 3.383C/IMP Segment RH REV 1.250 x 3.75
1380867 3 3 6.13 3.38 3.383C/IMP Segment LH REV 1.250 x 3.75
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1231.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3
988 F Straight Rock9U4187 2Q3968 1456507 4E8102 9U4193 1456497 1456498 2Q3130Serial Number:
4E8112 1 WOSB 21Base Edge 1032.90 468.522.000 x 13.750 x 148.500
2Q3133 1 WOSBBase Edge Without Holes
4E8106 2 IRRCorner LH/RH for 9J9600 Protector
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
2Q3137 2 IRRCorner with side bar RH/LH
1019350 1 DB|| 9 2.45 3.35 3.35 374.20 169.7391.500 x 19.000 x 52.375Center 1.250 x 3.75
1022184 2 DB|| 6 11.08 3.35 3.35 355.00 161.0361.500 x 19.000 x 49.250End 1.250 x 3.75
1073540 1 DB|| 9 2.48 3.35 3.35 520.80 236.2392.000 x 19.000 x 52.438HD Center 1.250 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 78©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1073541 2 DB|| 6 11.00 3.38 3.38 493.70 223.9462.000 x 19.000 x 49.250HD End 1.250 x 3.75
1019350FHA 1 HA|| 9 2.25 3.35 3.35 349.50 158.5391.750 x 13.500 x 51.979Half Arrow Center (Fabricated) 1.250 x 3.75
1022184FHA 2 HA|| 6 11.00 3.38 3.38 335.10 152.0061.750 x 13.500 x 49.250HA End (Fabricated) 1.250 x 3.75
1321068 1 9C/IMP Center NR x 3.75
1321067 2 6C/IMP End NR x 3.75
TEETH 8J450 or J550 Options
1019435 7 DB|| 3 3.47 3.35 3.35 98.90 44.8631.500 x 19.000 x 13.625Segment 1.250 x 3.75
1073536 7 DB|| 3 3.47 3.35 3.35 113.90 51.6631.750 x 19.000 x 13.625HD Segment 1.250 x 3.75
1099080 7 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
1099080HD 7 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1957180CAST 7 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1380865 7 3 3.44 3.38 3.383C/IMP Segment REV 1.250 x 3.75
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
988 F Spade Nose Rock1495910Serial Number:
1466302 1 SB\_/ 27Spade Nose Base Edge 1634.30 741.312.000 x 25.787 x 150.472
4E6474 2 IRR 3Corner LH/RH for 9J9600 Protector 116.40 52.801.250 x 11.063 x 59.125
9J9600 2 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
7K9309FAB 1 IRRCorner no holes RH 39.60 17.961.750 x 10.758 x 12.500
7K9310FAB 1 IRRCorner no holes LH 39.60 17.961.750 x 10.758 x 12.500
TEETH 8J450 or J550 Options
9W5734 1 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Segment 1.250 x 3.75
9W5737 3 DB\\ 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment RH 1.250 x 3.75
9W5730 3 DB// 3 5.53 3.35 3.35 87.00 39.4631.375 x 19.000 x 17.750Segment LH 1.250 x 3.75
9W8367 1 DB\\ 3 6.78 3.35 3.35 100.30 45.5031.375 x 19.000 x 20.250Optional Longer End Segment RH 1.250 x 3.75
9W8368 1 DB// 3 6.78 3.35 3.35 100.30 45.5031.375 x 19.000 x 20.250Optional Longer End Segment LH 1.250 x 3.75
1073490 1 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Segment 1.250 x 3.75
1073491 3 DB\\ 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment RH 1.250 x 3.75
1073492 3 DB// 3 5.53 3.35 3.35 108.20 49.0831.750 x 19.000 x 17.750HD Segment LH 1.250 x 3.75
1167460 1 HA|| 3 2.80 3.35 3.35 86.64 39.3032.000 x 18.827 x 12.283HA Segment (Cast) 1.250 x 3.75
1167461 3 HA\\ 3 3.35 3.35 89.95 40.8032.000 x 18.827 x 12.283HA Segment RH (Cast) 1.250 x 3.75
1167462 3 HA// 3 3.35 3.35 90.61 41.1032.000 x 18.827 x 12.283HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1386470 1 DB|| 3 2.80 3.35 3.35 82.00 37.1931.375 x 18.996 x 12.283C/IMP Segment REV 1.250 x 3.75
1386471 3 DB\\ 3 5.57 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment RH REV 1.250 x 3.75
1386472 3 DB// 3 5.53 3.35 3.35 82.00 37.1931.375 x 18.996 x 17.815C/IMP Segment LH REV 1.250 x 3.75
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 79©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.121.375 x 10.000 x 31.750Base Edge Wear Plate 1.000
988 G Spade Nose Rock1751451Serial Number:
1366176 1 SB\_/ 27Spade Nose Base For Segments 1659.00 752.512.000 x x
1686529 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
TEETH 8J450 or J550 Options
1140464 2 ADPJ460 Weld-On Center Adapter 41.70 18.915.835 x 4.850 x 17.016
1140465 3 ADPJ460 Weld-On RH Adapter 41.70 18.915.835 x 4.850 x 17.016
1140466 3 ADPJ460 Weld-On LH Adapter 41.70 18.915.835 x 4.850 x 17.016
1386554 2 ADPJ550 Weld-On Center Adapter 69.70 31.625.972 x 5.512 x 17.811
1386555 3 ADPJ550 Weld-On RH Adapter 69.20 31.395.972 x 5.512 x 17.811
1386556 3 ADPJ550 Weld-On LH Adapter 69.20 31.395.972 x 5.512 x 17.811
1019435 1 DB|| 3 3.47 3.35 3.35 98.90 44.8631.500 x 19.000 x 13.625Segment 1.250 x 3.75
1019436 3 DB\\ 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment RH 1.250 x 3.75
1019437 3 DB// 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment LH 1.250 x 3.75
1073536 1 DB|| 3 3.47 3.35 3.35 113.90 51.6631.750 x 19.000 x 13.625HD Segment 1.250 x 3.75
1073537 3 DB\\ 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment RH 1.250 x 3.75
1073538 3 DB// 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment LH 1.250 x 3.75
1099080 1 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
1099081 3 HA\\ 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment RH (Cast) 1.250 x 3.75
1099082 3 HA// 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment LH (Cast) 1.250 x 3.75
1099080HD 1 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1099081HD 3 HA\\ 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment RH (Cast) 1.250 x 3.75
1099082HD 3 HA// 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1380865 1 3 3.44 3.38 3.383C/IMP Segment REV 1.250 x 3.75
1380866 3 3 6.13 3.38 3.383C/IMP Segment RH REV 1.250 x 3.75
1380867 3 3 6.13 3.38 3.383C/IMP Segment LH REV 1.250 x 3.75
1366204 2 IRR 63.00 28.581.625 x 9.250 x 20.625Weld-On Wear Plate
1546367 2 IRR 49.80 22.591.000 x 6.500 x 30.500Weld-On Wear Plate
1366205 1 IRR 34.40 15.601.000 x 10.750 x 16.250Weld-On Wear Plate
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1231.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3
988 G Straight Rock1751455Serial Number:
1561039 1 WOSB 21Base Edge With Segment Holes 1270.20 576.152.000 x 16.456 x 149.606
1931756 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
TEETH 8J450 or J550 Options
1019435 7 DB|| 3 3.47 3.35 3.35 98.90 44.8631.500 x 19.000 x 13.625Segment 1.250 x 3.75
1073536 7 DB|| 3 3.47 3.35 3.35 113.90 51.6631.750 x 19.000 x 13.625HD Segment 1.250 x 3.75
1099080 7 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 80©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1099080HD 7 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1957180CAST 7 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1380865 7 3 3.44 3.38 3.383C/IMP Segment REV 1.250 x 3.75
1366204 2 IRR 63.00 28.581.625 x 9.250 x 20.625Weld-On Wear Plate
1546367 2 IRR 49.80 22.591.000 x 6.500 x 30.500Weld-On Wear Plate
1366205 1 IRR 34.40 15.601.000 x 10.750 x 16.250Weld-On Wear Plate
988 G Stepped Spade Nose Rock1751463Serial Number:
1950411 1 SB\_/ 27Stepped Spade Nose Base Edge 1905.00 864.092.000 x 31.060 x 153.520
1783702 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
TEETH 8J450 or J550 Options
1019435 1 DB|| 3 3.47 3.35 3.35 98.90 44.8631.500 x 19.000 x 13.625Segment 1.250 x 3.75
1019436 3 DB\\ 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment RH 1.250 x 3.75
1019437 3 DB// 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment LH 1.250 x 3.75
1073536 1 DB|| 3 3.47 3.35 3.35 113.90 51.6631.750 x 19.000 x 13.625HD Segment 1.250 x 3.75
1073537 3 DB\\ 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment RH 1.250 x 3.75
1073538 3 DB// 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment LH 1.250 x 3.75
1099080 1 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
1099081 3 HA\\ 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment RH (Cast) 1.250 x 3.75
1099082 3 HA// 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment LH (Cast) 1.250 x 3.75
1099080HD 1 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1099081HD 3 HA\\ 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment RH (Cast) 1.250 x 3.75
1099082HD 3 HA// 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1380865 1 3 3.44 3.38 3.383C/IMP Segment REV 1.250 x 3.75
1380866 3 3 6.13 3.38 3.383C/IMP Segment RH REV 1.250 x 3.75
1380867 3 3 6.13 3.38 3.383C/IMP Segment LH REV 1.250 x 3.75
1366204 2 IRR 63.00 28.581.625 x 9.250 x 20.625Weld-On Wear Plate
1546367 2 IRR 49.80 22.591.000 x 6.500 x 30.500Weld-On Wear Plate
1366205 1 IRR 34.40 15.601.000 x 10.750 x 16.250Weld-On Wear Plate
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1231.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3
988 G Spade Nose Rock1946256Serial Number:
1495915 1 SB\_/ 34Spade Nose Base Edge 1763.40 799.862.000 x 27.559 x 156.000
1946261 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
9W5734 1 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Center 1.250 x 3.75
9W5733 1 DB|| 5 4.17 6.38 3.35 191.10 86.6851.375 x 19.000 x 27.794Center 1.250 x 3.75
9W5736 1 DB\\ 6 4.71 3.35 3.35 214.00 97.0761.375 x 19.000 x 36.238Center RH 1.250 x 3.75
9W5735 1 DB\\ 5 6.87 6.71 3.35 198.30 89.9551.375 x 19.000 x 33.878End RH 1.250 x 3.75
9W5731 1 DB// 6 4.71 3.35 3.35 214.00 97.0761.375 x 19.000 x 36.238Center LH 1.250 x 3.75
9W5732 1 DB// 5 6.89 6.71 3.35 198.30 89.9551.375 x 19.000 x 33.878End LH 1.250 x 3.75
1073490 1 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Center 1.250 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 81©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1061096 1 DB|| 5 4.16 6.38 3.35 233.20 105.7851.750 x 19.000 x 27.813HD Center 1.250 x 3.75
1061098 1 DB\\ 6 4.67 3.35 3.35 260.40 118.1261.750 x 19.000 x 36.188HD Intermediate End RH 1.250 x 3.75
1061097 1 DB\\ 5 6.88 6.71 3.35 240.70 109.1851.750 x 19.000 x 33.875HD End RH 1.250 x 3.75
1061094 1 DB// 6 4.67 3.35 3.35 260.40 118.1261.750 x 19.000 x 36.188HD Intermediate End LH 1.250 x 3.75
1061095 1 DB// 5 6.88 6.71 3.35 240.70 109.1851.750 x 19.000 x 33.875HD End LH 1.250 x 3.75
9W5734HA 1 HA|| 3 2.78 3.35 3.35 83.00 37.651.750 x 16.000 x 12.250Half Arrow Center (Cast) 1.250 x 3.75
9W5733HA 1 HA|| 5 4.18 6.38 3.35 189.90 86.141.750 x 16.000 x 27.813Half Arrow Center (Cast) 1.250 x 3.75
9W5736HA 1 HA\\ 6 2.02 3.35 3.35 209.50 95.031.750 x 16.000 x 30.142Half Arrow Center RH (Cast) 1.250 x 3.75
9W5735HA 1 HA\\ 4 4.03 6.72 3.35 192.60 87.361.750 x 16.000 x 27.847HA End RH (Cast) 1.250 x 3.75
9W5731HA 1 HA// 6 2.02 3.35 3.35 209.50 95.031.750 x 16.000 x 30.142Half Arrow Center LH (Cast) 1.250 x 3.75
9W5732HA 1 HA// 4 4.03 6.72 3.35 192.60 87.361.750 x 16.000 x 27.847HA End LH (Cast) 1.250 x 3.75
1366204 2 IRR 63.00 28.581.625 x 9.250 x 20.625Weld-On Wear Plate
1546367 2 IRR 49.80 22.591.000 x 6.500 x 30.500Weld-On Wear Plate
1366205 1 IRR 34.40 15.601.000 x 10.750 x 16.250Weld-On Wear Plate
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1231.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3
988 G Stepped Spade Nose Rock1751453Serial Number:
1566388 1 SB\_/ 27Stepped Spade Nose Base Edge 1751.70 794.562.000 x 27.756 x 156.693
1783702 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
1140464 8 ADPJ460 Weld-On Center Adapter 41.70 18.915.835 x 4.850 x 17.016
1386554 8 ADPJ550 Weld-On Center Adapter 69.70 31.625.972 x 5.512 x 17.811
TEETH 8J450 or J550 Options
1019435 1 DB|| 3 3.47 3.35 3.35 98.90 44.8631.500 x 19.000 x 13.625Segment 1.250 x 3.75
1019436 3 DB\\ 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment RH 1.250 x 3.75
1019437 3 DB// 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment LH 1.250 x 3.75
1073536 1 DB|| 3 3.47 3.35 3.35 113.90 51.6631.750 x 19.000 x 13.625HD Segment 1.250 x 3.75
1073537 3 DB\\ 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment RH 1.250 x 3.75
1073538 3 DB// 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment LH 1.250 x 3.75
1099080 1 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
1099081 3 HA\\ 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment RH (Cast) 1.250 x 3.75
1099082 3 HA// 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment LH (Cast) 1.250 x 3.75
1099080HD 1 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1099081HD 3 HA\\ 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment RH (Cast) 1.250 x 3.75
1099082HD 3 HA// 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1380865 1 3 3.44 3.38 3.383C/IMP Segment REV 1.250 x 3.75
1380866 3 3 6.13 3.38 3.383C/IMP Segment RH REV 1.250 x 3.75
1380867 3 3 6.13 3.38 3.383C/IMP Segment LH REV 1.250 x 3.75
1366204 2 IRR 63.00 28.581.625 x 9.250 x 20.625Weld-On Wear Plate
1546367 2 IRR 49.80 22.591.000 x 6.500 x 30.500Weld-On Wear Plate
1366205 1 IRR 34.40 15.601.000 x 10.750 x 16.250Weld-On Wear Plate
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1231.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3
988 F High Capacity/Heavy Duty Quarry2Q7112 1456509Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 82©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4E7616 1 SB\_/ 27Spade Nose Base Edge 1606.90 728.882.000 x 25.787 x 148.504
1456987 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
TEETH 8J450 or J550 Options
1019435 3 DB|| 3 3.47 3.35 3.35 98.90 44.8631.500 x 19.000 x 13.625Segment 1.250 x 3.75
1019436 2 DB\\ 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment RH 1.250 x 3.75
1019437 2 DB// 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment LH 1.250 x 3.75
1073536 3 DB|| 3 3.47 3.35 3.35 113.90 51.6631.750 x 19.000 x 13.625HD Segment 1.250 x 3.75
1073537 2 DB\\ 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment RH 1.250 x 3.75
1073538 2 DB// 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment LH 1.250 x 3.75
1099080 3 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
1099081 2 HA\\ 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment RH (Cast) 1.250 x 3.75
1099082 2 HA// 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment LH (Cast) 1.250 x 3.75
1099080HD 3 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1099081HD 2 HA\\ 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment RH (Cast) 1.250 x 3.75
1099082HD 2 HA// 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 3 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 2 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 2 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1380865 1 3 3.44 3.38 3.383C/IMP Segment REV 1.250 x 3.75
1380866 3 3 6.13 3.38 3.383C/IMP Segment RH REV 1.250 x 3.75
1380867 3 3 6.13 3.38 3.383C/IMP Segment LH REV 1.250 x 3.75
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1231.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3
7T9127 2 DB|> 5 3.69 6.00 6.00 150.20 68.1331.375 x 13.000 x 32.438Base Edge Wear Plate with HA segment 1.000 x 3
988 F High Capacity/Heavy Duty Quarry1456507 2Q7052Serial Number:
2Q7018 1 SB\_/ 28Spade Nose Base Edge 2118.90 961.122.500 x 27.375 x 152.000
1456988 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 4 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1U4933 1 DB|| 7 2.38 6.00 6.00 148.60 67.4041.375 x 10.000 x 40.750Base Edge Wear Plate 1.000 x 3.25
4T6617 1 DB|| 9 3.13 6.00 6.00 159.10 72.1740.875 x 13.000 x 54.250Base Edge Wear Plate with HA segment 1.000 x 3.25
TEETH 7J550 Options
4T6760 2 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 2 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 2 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 2 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 2 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 2 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 2 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 2 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 2 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 2 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 2 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 2 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 83©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2755470 2 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 2 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 2 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 2 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 2 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 2 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
1380861 2 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
1380862 2 DB\\ 4 4C/IMP Segment RH REV 1.250 x 4.125
1380863 2 DB// 4 4C/IMP Segment LH REV 1.250 x 4.125
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
988 F High Capacity/Heavy Duty Quarry1456508 2Q4334Serial Number:
2Q4344 1 WOSB 21Stepped Spade Nose Base Edge
2Q4338 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
TEETH 8J450 or J550 Options
1019435 1 DB|| 3 3.47 3.35 3.35 98.90 44.8631.500 x 19.000 x 13.625Segment 1.250 x 3.75
1019436 3 DB\\ 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment RH 1.250 x 3.75
1019437 3 DB// 3 6.15 3.35 3.35 101.20 45.9031.500 x 19.000 x 19.000Segment LH 1.250 x 3.75
1073536 1 DB|| 3 3.47 3.35 3.35 113.90 51.6631.750 x 19.000 x 13.625HD Segment 1.250 x 3.75
1073537 3 DB\\ 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment RH 1.250 x 3.75
1073538 3 DB// 3 6.15 3.35 3.35 116.40 52.8031.750 x 19.000 x 19.000HD Segment LH 1.250 x 3.75
1099080 1 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
1099081 3 HA\\ 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment RH (Cast) 1.250 x 3.75
1099082 3 HA// 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment LH (Cast) 1.250 x 3.75
1099080HD 1 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1099081HD 3 HA\\ 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment RH (Cast) 1.250 x 3.75
1099082HD 3 HA// 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment LH (Cast) 1.250 x 3.75
1957180CAST 1 DB|| 3 3.40 3.35 3.35 34.30 15.5631.250 x 8.244 x 13.500Bolt on Top Plate Center 1.250 x 5
1957181CAST 3 DB\\ 3 5.06 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate RH 1.250 x 5
1957182CAST 3 DB// 3 4.33 3.35 3.35 35.40 16.0631.250 x 8.244 x 13.950Bolt on Top Plate LH 1.250 x 5
1380865 1 3 3.44 3.38 3.383C/IMP Segment REV 1.250 x 3.75
1380866 3 3 6.13 3.38 3.383C/IMP Segment RH REV 1.250 x 3.75
1380867 3 3 6.13 3.38 3.383C/IMP Segment LH REV 1.250 x 3.75
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
988 G High Capacity/Heavy Duty Quarry1751459Serial Number:
2Q7018 1 SB\_/ 28Spade Nose Base Edge 2118.90 961.122.500 x 27.375 x 152.000
1938221 2 IRRCorner LH/RH for 2-9J9600 Protectors
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 84©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J550 Options
4T6760 2 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 2 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 2 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 2 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 2 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 2 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 2 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 2 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 2 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 2 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 2 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 2 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 2 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 2 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 2 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 2 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 2 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 2 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
1380861 2 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
1380862 2 DB\\ 4 4C/IMP Segment RH REV 1.250 x 4.125
1380863 2 DB// 4 4C/IMP Segment LH REV 1.250 x 4.125
1366204 2 IRR 63.00 28.581.625 x 9.250 x 20.625Weld-On Wear Plate
1546367 2 IRR 49.80 22.591.000 x 6.500 x 30.500Weld-On Wear Plate
1366205 1 IRR 34.40 15.601.000 x 10.750 x 16.250Weld-On Wear Plate
1U4933 1 DB|| 7 2.38 6.00 6.00 148.60 67.4041.375 x 10.000 x 40.750Base Edge Wear Plate 1.000 x 3.25
4T6617 1 DB|| 9 3.13 6.00 6.00 159.10 72.1740.875 x 13.000 x 54.250Base Edge Wear Plate with HA segment 1.000 x 3.25
988 A Modulok2V6147Serial Number:
4E0055 1 SB\_/Modulok Base Edge Assembly x x 132.100
4T6384 2 DB|| 6 2.50 6.00 6.00 134.50 61.0161.125 x 13.000 x 35.000Center Base Edge Wear Plate 1.000 x 3
4T6390 2 DB|| 8End Base Edge Wear Plate 1.000 x 3
4T6540 2 DB|| 6 2.75 6.00 6.00 168.90 76.6161.375 x 13.000 x 35.500HD Center Base Edge Wear Plate 1.000 x 3
4T6553 2 DB|| 8HD End Base Edge Wear Plate 1.000 x 3
TEETH 8J450 Options
988 A ModulokNONESerial Number:
4E0051 1 SB||Modulok Base Edge Assembly x x 132.100
4T6393 2 DB|| 5 2.81 6.00 6.00 113.00 51.2651.125 x 13.000 x 29.625Center Base Edge Wear Plate 1.000 x 3
4T6384 2 DB|| 6 2.50 6.00 6.00 134.50 61.0161.125 x 13.000 x 35.000Center Base Edge Wear Plate 1.000 x 3
4T6539 2 DB|| 5 2.81 6.00 6.00 140.90 63.9151.375 x 13.000 x 29.625HD Center Base Edge Wear Plate 1.000 x 3
4T6540 2 DB|| 6 2.75 6.00 6.00 168.90 76.6161.375 x 13.000 x 35.500HD End Base Edge Wear Plate 1.000 x 3
TEETH 8J450 Options
988 B Modulok5V1224 9V1344 9V0219 2Q4434 4E0065Serial Number:
4E0064 1Modulok Base Edge Assembly 2.000 x x 143.500
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 85©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6384 2 DB|| 6 2.50 6.00 6.00 134.50 61.0161.125 x 13.000 x 35.000Center Base Edge Wear Plate 1.000 x 3.25
4T6383 2 DB|> 6 2.56 6.00 6.00 133.10 60.3761.125 x 13.000 x 35.125End Base Edge Wear Plate 1.000 x 3.25
4T6540 2 DB|| 6 2.75 6.00 6.00 168.90 76.6161.375 x 13.000 x 35.500HD Center Base Edge Wear Plate 1.000 x 3.25
4T6541 2 DB|> 6 2.81 6.00 6.00 166.90 75.7061.375 x 13.000 x 36.000HD End Base Edge Wear Plate 1.000 x 3.25
TEETH 8J450 Options
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 32 1.38 24.00 ...2nd Row1.000 x 3
988 F Modulok9U4183 2Q3257 1456502Serial Number:
8R5610 1 SB\_/Modulok Base Edge Assembly 2.000 x x 148.700
8R5611 1 SB\_/ 16Spade Nose Base Edge 1538.60 697.902.000 x 23.504 x 148.031
9U9862 2 DB|| 6 5.25 6.00 6.00 144.00 65.3261.125 x 13.000 x 37.625Center Base Edge Wear Plate 1.000 x 3.25
4T6383 2 DB|> 6 2.56 6.00 6.00 133.10 60.3761.125 x 13.000 x 35.125End Base Edge Wear Plate 1.000 x 3.25
6I8607 2 DB|| 6 2.38 6.00 6.00 178.00 80.7461.375 x 13.000 x 37.625Center Base Edge Wear Plate 1.000 x 3.25
4T6541 2 DB|> 6 2.81 6.00 6.00 166.90 75.7061.375 x 13.000 x 36.000End Base Edge Wear Plate 1.000 x 3.25
TEETH 8J450 Options
9V5793 2 DB|| 4 1.38 24.00 55.10 24.9921.000 x 10.000 x 26.750Rear Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
6Y3609 2 DB|| 4 1.38 24.00 75.80 34.3821.375 x 10.000 x 26.750Heavy Duty Wear Plate 1.000 x 3.252 1.38 24.00 ...2nd Row1.000 x 3.25
1324713 2 DB|| 4 1.38 24.0021.000 x 10.000 x 26.750Hex Bolt Wear Plate 1.000 x 32 1.38 24.00 ...2nd Row1.000 x 3
988 H Spade Nose Rock2462755Serial Number:
1495915 1 SB\_/ 34Spade Nose Base Edge 1763.40 799.862.000 x 27.559 x 156.000
9W5734 1 DB|| 3 2.78 3.35 3.35 83.40 37.8331.375 x 19.000 x 12.250Center 1.250 x 3.75
9W5733 1 DB|| 5 4.17 6.38 3.35 191.10 86.6851.375 x 19.000 x 27.794Center 1.250 x 3.75
9W5736 1 DB\\ 6 4.71 3.35 3.35 214.00 97.0761.375 x 19.000 x 36.238Center RH 1.250 x 3.75
9W5735 1 DB\\ 5 6.87 6.71 3.35 198.30 89.9551.375 x 19.000 x 33.878End RH 1.250 x 3.75
9W5731 1 DB// 6 4.71 3.35 3.35 214.00 97.0761.375 x 19.000 x 36.238Center LH 1.250 x 3.75
9W5732 1 DB// 5 6.89 6.71 3.35 198.30 89.9551.375 x 19.000 x 33.878End LH 1.250 x 3.75
1073490 1 DB|| 3 2.78 3.35 3.35 101.00 45.8131.750 x 19.000 x 12.250HD Center 1.250 x 3.75
1061096 1 DB|| 5 4.16 6.38 3.35 233.20 105.7851.750 x 19.000 x 27.813HD Center 1.250 x 3.75
1061098 1 DB\\ 6 4.67 3.35 3.35 260.40 118.1261.750 x 19.000 x 36.188HD Intermediate End RH 1.250 x 3.75
1061097 1 DB\\ 5 6.88 6.71 3.35 240.70 109.1851.750 x 19.000 x 33.875HD End RH 1.250 x 3.75
1061094 1 DB// 6 4.67 3.35 3.35 260.40 118.1261.750 x 19.000 x 36.188HD Intermediate End LH 1.250 x 3.75
1061095 1 DB// 5 6.88 6.71 3.35 240.70 109.1851.750 x 19.000 x 33.875HD End RH 1.250 x 3.75
9W5734HA 1 HA|| 3 2.78 3.35 3.35 83.00 37.651.750 x 16.000 x 12.250Half Arrow Center (Cast) 1.250 x 3.75
9W5733HA 1 HA|| 5 4.18 6.38 3.35 189.90 86.141.750 x 16.000 x 27.813Half Arrow Center (Cast) 1.250 x 3.75
9W5736HA 1 HA\\ 6 2.02 3.35 3.35 209.50 95.031.750 x 16.000 x 30.142Half Arrow Center RH (Cast) 1.250 x 3.75
9W5735HA 1 HA\\ 4 4.03 6.72 3.35 192.60 87.361.750 x 16.000 x 27.847HA End RH (Cast) 1.250 x 3.75
9W5731HA 1 HA// 6 2.02 3.35 3.35 209.50 95.031.750 x 16.000 x 30.142Half Arrow Center LH (Cast) 1.250 x 3.75
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 86©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W5732HA 1 HA// 4 4.03 6.72 3.35 192.60 87.361.750 x 16.000 x 27.847HA End LH (Cast) 1.250 x 3.75
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1231.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3
988 H Spade Nose Rock2462770Serial Number:
2Q7018 1 SB\_/ 28Spade Nose Base Edge 2118.90 961.122.500 x 27.375 x 152.000
4T6617 1 DB|| 9 3.13 6.00 6.00 159.10 72.1740.875 x 13.000 x 54.250Bolt-On Wear Plate 1.000 x 3.25
1073554 1J550 Weld-On Center Adapter 98.00 44.457.362 x 6.299 x 21.756
1073555 3J550 Weld-On RH Adapter 98.00 44.457.362 x 6.299 x 22.268
1073556 3J550 Weld-On LH Adapter 98.00 44.457.362 x 6.299 x 22.268
4T6760 2 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 2 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 2 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 2 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 2 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 2 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 2 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 2 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 2 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 2 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 2 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 2 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 2 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 2 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 2 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 2 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 2 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 2 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
1380861 2 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
1380862 2 DB\\ 4 4C/IMP Segment RH REV 1.250 x 4.125
1380863 2 DB// 4 4C/IMP Segment LH REV 1.250 x 4.125
988 H Spade Nose Rock2462772Serial Number:
2573694BASE 1 SB\_/Stepped Spade Nose Base Edge 2.500 x x 154.567
4T6540 2 DB|| 6 2.75 6.00 6.00 168.90 76.611.375 x 13.000 x 35.500Base Edge Wear Plate 1.000
1099080 3 HA|| 3 3.39 3.35 3.35 104.70 47.4932.000 x 18.827 x 13.465HA Segment (Cast) 1.250 x 3.75
1099081 2 HA\\ 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment RH (Cast) 1.250 x 3.75
1099082 2 HA// 3 2.65 3.35 3.35 109.30 49.5832.000 x 18.827 x 13.465HA Segment LH (Cast) 1.250 x 3.75
1099080HD 3 HA|| 3 3.39 3.35 3.35 108.50 49.2132.000 x 17.785 x 13.465HD HA Segment (Cast) 1.250 x 3.75
1099081HD 2 HA\\ 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment RH (Cast) 1.250 x 3.75
1099082HD 2 HA// 3 3.39 3.35 3.35 112.70 51.1232.000 x 17.750 x 13.465HD HA Segment LH (Cast) 1.250 x 3.75
2337167 2 DB||Bolt on Top Plate Center
2530191 2 DB||Bolt on Top Plate LH
2530192 2 DB||Bolt on Top Plate RH
988 H Spade Nose Rock2462772 2831941 2888251Serial Number:
2788185BASE 1 SB\_/Stepped Spade Nose Base Edge 2.500 x x 154.567
2788186 2 IRRCorner LH/RH for 2-9J9600 Protectors
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 87©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9J9600 4 IRR 2Sidebar Protector 44.50 20.181.500 x 6.938 x 22.688
2512180 5 ADPCCenter Adapter Cover 60.41 27.404.716 x 5.444 x 13.752
2512461 2 ADPCEnd Adapter Cover 57.76 26.204.700 x 5.444 x 13.752
2571782 2 HA|| 4 2.98 3.35 3.35 126.32 57.3042.000 x 17.323 x 16.000HA Segment (Cast) 1.250 x 4.125
2571783 2 HA\\ 4 3.16 3.35 3.35 121.25 55.0042.000 x 17.323 x 16.000HA Segment RH (Cast) 1.250 x 4.125
2571784 2 HA// 4 3.15 3.35 3.35 121.25 55.0042.000 x 17.323 x 16.000HA Segment LH (Cast) 1.250 x 4.125
2571778 2 DB|| 4 2.86 3.35 3.35 36.16 16.4041.000 x 9.645 x 15.750Bolt on Top Plate Center 1.250 x 4.5
2571779 2 DB\\ 4 4.53 3.35 3.35 40.12 18.2041.000 x 9.645 x 19.084Bolt on Top Plate RH 1.250 x 4.5
2571781 2 DB// 4 4.53 3.35 3.35 40.12 18.2041.000 x 9.645 x 19.084Bolt on Top Plate LH 1.250 x 4.5
4T6617 1 DB|| 9 3.13 6.00 6.00 159.10 72.1790.875 x 13.000 x 54.250Base Edge Wear Plate 1.000 x 4
2556710 1 SE\_/Weld-On Bucket Wear Plate
2556711 1 IRRWeld-On Bucket Wear Plate
2556712 1 IRRWeld-On Bucket Wear Plate
2573655 2 IRRWeld-On Bucket Wear Plate
990 Spade Nose Rock1019178 1122118Serial Number:
1019188 1 WOSBSpade Nose Base Edge Without Holes 2.500 x x 175.200
1456990 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
TEETH 8J550 Options
6Y3573 2 DB|_| 4 1.38 29.25 128.40 58.2421.375 x 13.000 x 32.000Rear Wear Plate 1.000 x 3.52 1.38 29.25 ...2nd Row1.000 x 3.5
990 Spade Nose Rock1515979Serial Number:
1515980 1 SB\_/ 40Spade Nose Base Edge 2.500 x 31.500 x 175.200
1456989 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
6Y3573 2 DB|_| 4 1.38 29.25 128.40 58.2421.375 x 13.000 x 32.000Rear Wear Plate 1.000 x 3.52 1.38 29.25 ...2nd Row1.000 x 3.5
990 Spade Nose Rock9U2027 4E9885Serial Number:
4E9915 1 SB\_/ 36Spade Nose Base Edge 2825.001281.402.500 x 31.500 x 175.200
1456990 2 IRRCorner RH/LH
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1241.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3.25
9U9862 2 DB|| 6 5.25 6.00 6.00 144.00 65.3241.125 x 13.000 x 37.625Base Edge Wear Plate with HA segment 1.000 x 3.25
1066420 1 DB|| 6 4.29 6.69 3.54 310.00 140.6141.500 x 26.000 x 32.600Center 1.250 x 4.125
1066421 1 DB\\ 6 8.88 3.93 3.93 344.00 156.0441.500 x 23.250 x 46.688Center RH 1.250 x 4.125
1623297 1 DB\\ 10 7.69 3.25 3.25 290.00 131.5441.500 x 23.250 x 40.188End RH 1.250 x 4.125
1066423 1 DB// 6 8.88 3.94 3.94 344.00 156.0441.500 x 23.250 x 46.688Center LH 1.250 x 4.125
1623296 1 DB// 10 7.69 3.25 3.25 385.00 174.6341.500 x 23.250 x 40.188End LH 1.250 x 4.125
1066420FHA 1 HA|| 6 4.30 6.69 3.54 429.00 194.5942.000 x 19.690 x 32.600Half Arrow Center (Fabricated) 1.250 x 4.125
1066421FHA 1 HA\\ 6 6.75 3.94 3.94 456.00 206.8442.000 x 17.880 x 45.258Half Arrow Center RH (Fabricated) 1.250 x 4.125
1623297FHA 1 HA\\ 6 11.65 3.25 3.94 375.00 170.1042.000 x 17.880 x 38.770HA End RH (Fabricated) 1.250 x 4.125
1066423FHA 1 HA// 6 6.75 3.94 3.94 456.00 206.8442.000 x 17.880 x 45.258Half Arrow Center LH (Fabricated) 1.250 x 4.125
1623296FHA 1 HA// 6 11.65 3.25 3.94 375.00 170.1042.000 x 17.880 x 38.770HA End LH (Fabricated) 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 88©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J550 Options
4T6760 1 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 3 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 3 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 1 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 3 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 3 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 1 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 3 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 3 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 1 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 3 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 3 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
1380861 1 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
1380862 3 DB\\ 4 4C/IMP Segment RH REV 1.250 x 4.125
1380863 3 DB// 4 4C/IMP Segment LH REV 1.250 x 4.125
6Y3573 2 DB|_| 4 1.38 29.25 128.40 58.2421.375 x 13.000 x 32.000Rear Wear Plate 1.000 x 3.52 1.38 29.25 ...2nd Row1.000 x 3.5
990 General Purpose1019181 1019180Serial Number:
1019186 1 WOSB 28Base Edge With Segment Holes 1981.00 898.572.500 x 17.360 x 175.250
1456990 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1066377 2 DB|| 5 5.21 13.56 3.54 284.00 128.8241.500 x 23.220 x 31.890Center 1.250 x 4.125
1066378 2 DB|| 8 10.75 3.54 3.54 501.00 227.2541.500 x 23.220 x 56.303End 1.250 x 4.125
TEETH 8J550 Options
4T6760 7 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
1073530 7 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1076294 7 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
2755460 7 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755470 7 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
1957096CAST 7 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1380861 7 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
6Y3573 2 DB|_| 4 1.38 29.25 128.40 58.2421.375 x 13.000 x 32.000Rear Wear Plate 1.000 x 3.52 1.38 29.25 ...2nd Row1.000 x 3.5
990 Flush Mounted Teeth1119043Serial Number:
1119049 1 WOSBBase Edge Without Holes 2358.001069.572.500 x 20.000 x 175.250
1456990 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 89©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TEETH 8J550 Options
6Y3573 2 DB|_| 4 1.38 29.25 128.40 58.2421.375 x 13.000 x 32.000Rear Wear Plate 1.000 x 3.52 1.38 29.25 ...2nd Row1.000 x 3.5
990 High Capacity/Heavy Duty Quarry2Q4239 2Q4246Serial Number:
2Q4247 1 SB\_/ 36Spade Nose Base Edge 2.500 x 34.680 x 181.500
1456990 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
4T6381 1 DB|| 9 2.63 6.00 6.00 204.60 92.8141.125 x 13.000 x 53.250Base Edge Wear Plate 1.000 x 3.25
6Y0313 DB|| 9 2.63 6.00 6.00 310.40 140.8041.375 x 16.000 x 53.250Base Edge Wear Plate with HA segment 1.000 x 3.25
TEETH 8J550 Options
4T6760 1 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 3 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 3 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 1 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 3 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 3 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 1 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 3 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 3 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 1 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 3 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 3 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
6Y3573 2 DB|_| 4 1.38 29.25 128.40 58.2421.375 x 13.000 x 32.000Rear Wear Plate 1.000 x 3.52 1.38 29.25 ...2nd Row1.000 x 3.5
990 High Capacity/Heavy Duty Quarry2Q7097 2Q7059Serial Number:
4E9915 1 SB\_/ 36Spade Nose Base Edge 2825.001281.402.500 x 31.500 x 175.200
1456993 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 4 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1U4929 2 DB|> 5 3.88 6.00 6.00 112.70 51.1241.375 x 10.000 x 31.750Base Edge Wear Plate 1.000 x 3.25
9U9862 2 DB|| 6 5.25 6.00 6.00 144.00 65.3241.125 x 13.000 x 37.625Base Edge Wear Plate with HA segment 1.000 x 3.25
TEETH 8J550 Options
4T6760 1 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 3 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 3 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 1 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 3 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 3 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 1 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 90©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1076295 3 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 3 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 1 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 3 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 3 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
1380861 1 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
1380862 3 DB\\ 4 4C/IMP Segment RH REV 1.250 x 4.125
1380863 3 DB// 4 4C/IMP Segment LH REV 1.250 x 4.125
6Y3573 2 DB|_| 4 1.38 29.25 128.40 58.2421.375 x 13.000 x 32.000Rear Wear Plate 1.000 x 3.52 1.38 29.25 ...2nd Row1.000 x 3.5
990 Modulok1019179Serial Number:
1026214 1 SB\_/Modulok Base Edge Assembly
1456991 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
4T6540 2 DB|| 6 2.75 6.00 6.00 168.90 76.611.375 x 13.000 x 35.500Center Base Edge Wear Plate 1.000
4T6541 2 DB|> 6 2.81 6.00 6.00 166.90 75.701.375 x 13.000 x 36.000End Base Edge Wear Plate 1.000
1006357 2 DB|| 6 2.75 6.00 6.00 211.00 95.711.750 x 13.000 x 35.500HD Center Base Edge Wear Plate 1.000
1006358 2 DB|> 6 2.75 6.00 6.00 218.20 98.971.750 x 13.000 x 36.625HD End Base Edge Wear Plate 1.000
TEETH 8J550 Options
6Y3573 2 DB|_| 4 1.38 29.25 128.40 58.2421.375 x 13.000 x 32.000Rear Wear Plate 1.000 x 3.52 1.38 29.25 ...2nd Row1.000 x 3.5
992 - B General Purpose9V0474 3V4417 8K7189 3V4415Serial Number:
9V0009 1 WOSBBase Edge Without Holes 1787.00 810.572.250 x 17.375 x 169.800
3V3894 1 IRRCorner no holes RH
3V3893 1 IRRCorner no holes LH
8K6489 1 IRRCorner no holes RH for no teeth
8K6490 1 IRRCorner no holes LH for no teeth
TEETH 8J550 Options
9K0071 2 DB||Rear Wear Plate
992 - B Spade Nose Rock8K7190 8K8501 2V6380 3V2468 3V2474Serial Number:
9V0008 1 SB\_/Spade Nose Base Edge Without Holes 2684.001217.442.250 x 33.000 x 169.800
3V3894 1 IRRCorner no holes RH
3V3893 1 IRRCorner no holes LH
8K6489 1 IRRCorner no holes RH for no teeth
8K6490 1 IRRCorner no holes LH for no teeth
TEETH 8J550 Options
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 91©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9K0071 2 DB||Rear Wear Plate
992 C Spade Nose Rock3V6623 3V6625Serial Number:
9V4370 1 SB\_/Spade Nose Base Edge Without Holes 3507.001590.752.500 x 36.250 x 181.000
4E6385 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
TEETH 8J550 or J700 Options
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 C General Purpose3V6627 3V6629Serial Number:
3V3890 1 WOSBBase Edge Without Holes 2617.001187.052.500 x 21.500 x 181.000
3V3894 1 IRRCorner no holes RH
3V3893 1 IRRCorner no holes LH
8K6489 1 IRRCorner no holes RH for no teeth
8K6490 1 IRRCorner no holes LH for no teeth
TEETH 8J550 Options
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 C Spade Nose Rock5V5601 5V5603 9V0208 9V0209Serial Number:
9V0005 1 SB\_/Spade Nose Base Edge Without Holes 3662.001661.062.500 x 36.375 x 187.000
9V6132 2 IRRCorner no holes LH/RH
8K6489 1 IRRCorner no holes RH for no teeth
8K6490 1 IRRCorner no holes LH for no teeth
TEETH 8J550 or J700 Options
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 C High Lift Spade Nose5V7360 9V0212Serial Number:
9V0006 1 SB\_/Spade Nose Base Edge Without Holes 3342.001515.912.500 x 33.000 x 187.000
4E6386 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
TEETH 8J550 or J700 Options
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 92©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 C General Purpose5V5605 9V0210Serial Number:
9V0007 1 WOSBBase Edge Without Holes 2704.001226.512.500 x 21.500 x 187.000
5V5403 2 IRRCorner no holes LH/RH
8K6489 1 IRRCorner no holes RH for no teeth
8K6490 4 IRRCorner no holes LH for no teeth
TEETH 8J550 or J700 Options
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 C D Spade Nose Rock9V3572 9U3014 7I3331 9U3014 7I3331 9U3012 1061789 2Q3960Serial Number:
4E6462 1 SB\_/ 38Spade Nose Base Edge 3572.701620.552.500 x 36.250 x 187.000
4E6385 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1U4933 2 DB|| 7 2.38 6.00 6.00 148.60 67.4031.375 x 10.000 x 40.750Base Edge Wear Plate 1.000 x 3.25
6Y0311 1 DB|> 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
6Y0312 1 DB<| 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
6I8364 1 DB|| 6 5.00 7.06 3.56 354.30 160.7161.500 x 26.125 x 34.813Center 1.250 x 4.125
6I8365 1 DB\\ 6 8.88 3.94 3.94 378.60 171.7361.500 x 23.250 x 48.250Center RH 1.250 x 4.125
6I8366 1 DB\\ 6 8.16 7.69 3.94 334.20 151.5961.500 x 23.250 x 43.500End RH 1.250 x 4.125
6I8367 1 DB// 6 8.88 3.94 3.94 378.60 171.7361.500 x 23.250 x 48.250Center LH 1.250 x 4.125
6I8368 1 DB// 6 8.16 7.69 3.94 334.20 151.5961.500 x 23.250 x 43.500End LH 1.250 x 4.125
1277429 1 DB|| 6 5.00 7.06 3.56 441.00 200.0362.000 x 26.125 x 34.813HD Center 1.250 x 4.125
1277433 1 DB\\ 6 8.88 3.94 3.94 512.30 232.3862.000 x 23.250 x 48.250HD Intermediate End RH 1.250 x 4.125
1277431 1 DB\\ 6 8.16 7.69 3.94 453.10 205.5262.000 x 23.250 x 43.500HD End RH 1.250 x 4.125
1277432 1 DB// 6 8.88 3.94 3.94 512.30 232.3862.000 x 23.250 x 48.250HD Intermediate End LH 1.250 x 4.125
1277430 1 DB// 6 8.16 7.69 3.94 453.10 205.5262.000 x 23.250 x 43.500HD End LH 1.250 x 4.125
6I8364FHA 1 HA|| 6 5.00 7.06 3.56 423.30 192.0162.000 x 18.625 x 34.812Half Arrow Center (Fabricated) 1.250 x 4.125
6I8365FHA 1 HA\\ 6 6.00 7.69 3.94 434.50 197.092.000 x 16.937 x 46.562 1.250
6I8366FHA 1 HA\\ 6 6.00 7.69 3.94 384.10 174.2262.000 x 16.937 x 41.812HA End RH (Fabricated) 1.250 x 4.125
6I8367FHA 1 HA// 6 6.75 3.94 3.94 434.50 197.0962.000 x 16.937 x 46.562Half Arrow Center LH (Fabricated) 1.250 x 4.125
6I8368FHA 1 HA// 6 6.00 7.69 3.94 384.10 174.2262.000 x 16.937 x 41.812HA End LH (Fabricated) 1.250 x 4.125
TEETH 8J550 or J700 Options
4T6760 1 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 3 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 3 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 1 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 93©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1073531 3 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 3 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 1 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 3 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 3 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 1 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 3 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 3 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
1380861 1 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
1380862 3 DB\\ 4 4C/IMP Segment RH REV 1.250 x 4.125
1380863 3 DB// 4 4C/IMP Segment LH REV 1.250 x 4.125
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 C D High Lift Spade Nose9V3568 4E8622Serial Number:
9V3566 1 SB\_/ 28Spade Nose Base Edge 3074.001394.342.500 x 33.000 x 187.000
4E6386 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
TEETH 8J550 or J700 Options
4T6760 1 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 3 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 3 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 1 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 3 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 3 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 1 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 3 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 3 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 1 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 3 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 3 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 94©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1380861 1 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
1380862 3 DB\\ 4 4C/IMP Segment RH REV 1.250 x 4.125
1380863 3 DB// 4 4C/IMP Segment LH REV 1.250 x 4.125
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 D General Purpose9U3011 1061790Serial Number:
9U3846 1 WOSBBase Edge With Segment Holes 2.500 x 21.300 x 187.000
1456995 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
TEETH 8J550 or J700 Options
4T6760 7 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
1073530 7 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1076294 7 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
2755460 7 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755470 7 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
1957096CAST 7 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1380861 7 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 D Heavy Duty Quarry Spade Nose2Q7121Serial Number:
1078570 1 SB\_/ 34Spade Nose Base Edge 2.750 x 36.300 x 187.000
1456995 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 4 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1U4933 2 DB|| 7 2.38 6.00 6.00 148.60 67.4031.375 x 10.000 x 40.750Base Edge Wear Plate 1.000 x 3.25
6Y0311 1 DB|> 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
6Y0312 1 DB<| 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
TEETH 8J600 Options
4T6760 1 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 3 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 3 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 1 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 3 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 3 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 1 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 3 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 3 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 95©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 1 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 3 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 3 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 G Spade Nose Rock1535620 1124195 1124202 1535620 1124195 1124202Serial Number:
1129033 1 SB\_/ 34Spade Nose Base Edge 3427.001554.462.750 x 32.530 x 189.907
1129005 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 4 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1U4933 2 DB|| 7 2.38 6.00 6.00 148.60 67.4031.375 x 10.000 x 40.750Base Edge Wear Plate 1.000 x 3.25
6Y0311 1 DB|> 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
6Y0312 1 DB<| 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
TEETH 8J600 or J700 Options
4T6760 1 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 3 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 3 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 1 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 3 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 3 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 1 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 3 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 3 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 1 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 3 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 3 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
1380861 1 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
1380862 3 DB\\ 4 4C/IMP Segment RH REV 1.250 x 4.125
1380863 3 DB// 4 4C/IMP Segment LH REV 1.250 x 4.125
1151548 2 IRR 124.50 56.471.375 x 16.000 x 25.000Weld-On Rear Wear Plate
1151549 1 IRR 90.00 40.821.375 x 10.000 x 28.543Weld-On Rear Wear Plate
992 G Spade Nose Rock1124199Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 96©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1327092 1 SB\_/ 38Spade Nose Base Edge 3115.451413.142.500 x 32.530 x 189.907
1128996 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 4 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1U4933 2 DB|| 7 2.38 6.00 6.00 148.60 67.4031.375 x 10.000 x 40.750Base Edge Wear Plate 1.000 x 3.25
6Y0311 1 DB|> 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
6Y0312 1 DB<| 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
TEETH 8J550 or J700 Options
4T6760 1 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 3 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 3 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 1 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 3 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 3 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 1 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 3 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 3 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 1 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 3 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 3 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
1380861 1 DB|| 4 4C/IMP Segment REV 1.250 x 4.125
1380862 3 DB\\ 4 4C/IMP Segment RH REV 1.250 x 4.125
1380863 3 DB// 4 4C/IMP Segment LH REV 1.250 x 4.125
1151548 2 IRR 124.50 56.471.375 x 16.000 x 25.000Weld-On Rear Wear Plate
1151549 1 IRR 90.00 40.821.375 x 10.000 x 28.543Weld-On Rear Wear Plate
992 G Spade Nose Rock1742281Serial Number:
1701748 1 SB\_/ 32Spade Nose Base Edge 3247.001472.812.750 x 33.980 x 189.920
1743391 1 IRRCorner LH/RH for 1U0740 Protectors
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1U4933 2 DB|| 7 2.38 6.00 6.00 148.60 67.4031.375 x 10.000 x 40.750Base Edge Wear Plate 1.000 x 3.25
6Y0311 1 DB|> 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
6Y0312 1 DB<| 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
6I8364 1 DB|| 6 5.00 7.06 3.56 354.30 160.7161.500 x 26.125 x 34.813Center 1.250 x 4.125
6I8365 1 DB\\ 6 8.88 3.94 3.94 378.60 171.7361.500 x 23.250 x 48.250Center RH 1.250 x 4.125
6I8366 1 DB\\ 6 8.16 7.69 3.94 334.20 151.5961.500 x 23.250 x 43.500End RH 1.250 x 4.125
6I8367 1 DB// 6 8.88 3.94 3.94 378.60 171.7361.500 x 23.250 x 48.250Center LH 1.250 x 4.125
6I8368 1 DB// 6 8.16 7.69 3.94 334.20 151.5961.500 x 23.250 x 43.500End LH 1.250 x 4.125
1277429 1 DB|| 6 5.00 7.06 3.56 441.00 200.0362.000 x 26.125 x 34.813HD Center 1.250 x 4.125
1277433 1 DB\\ 6 8.88 3.94 3.94 512.30 232.3862.000 x 23.250 x 48.250HD Intermediate End RH 1.250 x 4.125
1277431 1 DB\\ 6 8.16 7.69 3.94 453.10 205.5262.000 x 23.250 x 43.500HD End RH 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 97©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1277432 1 DB// 6 8.88 3.94 3.94 512.30 232.3862.000 x 23.250 x 48.250HD Intermediate End LH 1.250 x 4.125
1277430 1 DB// 6 8.16 7.69 3.94 453.10 205.5262.000 x 23.250 x 43.500HD End LH 1.250 x 4.125
6I8364FHA 1 HA|| 6 5.00 7.06 3.56 423.30 192.0162.000 x 18.625 x 34.812Half Arrow Center (Fabricated) 1.250 x 4.125
6I8365FHA 1 HA\\ 6 6.00 7.69 3.94 434.50 197.0962.000 x 16.937 x 46.562Half Arrow Center RH (Fabricated) 1.250 x 4.125
6I8366FHA 1 HA\\ 6 6.00 7.69 3.94 384.10 174.2262.000 x 16.937 x 41.812HA End RH (Fabricated) 1.250 x 4.125
6I8367FHA 1 HA// 6 6.75 3.94 3.94 434.50 197.0962.000 x 16.937 x 46.562Half Arrow Center LH (Fabricated) 1.250 x 4.125
6I8368FHA 1 HA// 6 6.00 7.69 3.94 384.10 174.2262.000 x 16.937 x 41.812HA End LH (Fabricated) 1.250 x 4.125
1151548 2 IRR 124.50 56.471.375 x 16.000 x 25.000Weld-On Rear Wear Plate
1151549 1 IRR 90.00 40.821.375 x 10.000 x 28.543Weld-On Rear Wear Plate
992 G Heavy Duty Quarry Spade Nose1467313Serial Number:
1468966 1 SB\_/ 34Spade Nose Base Edge 3.000 x x 189.921
1128996 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 4 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1U4933 2 DB|| 7 2.38 6.00 6.00 148.60 67.4031.375 x 10.000 x 40.750Base Edge Wear Plate 1.000 x 3.25
6Y0311 1 DB|> 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
6Y0312 1 DB<| 8 3.38 6.00 6.00 274.00 124.2831.375 x 16.000 x 48.125Base Edge Wear Plate with HA segment 1.000 x 3.25
TEETH 8J700 Options
4T6760 1 DB|| 4 2.75 3.56 3.56 156.00 70.7641.625 x 23.250 x 16.188Segment 1.250 x 4.125
4T6761 3 DB\\ 4 6.09 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment RH 1.250 x 4.125
4T6762 3 DB// 4 6.10 3.94 3.94 171.60 77.8441.625 x 23.250 x 24.000Segment LH 1.250 x 4.125
1073530 1 DB|| 4 2.75 3.56 3.56 194.30 88.1342.000 x 23.250 x 16.188HD Segment 1.250 x 4.125
1073531 3 DB\\ 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment RH 1.250 x 4.125
1073532 3 DB// 4 6.09 3.94 3.94 213.80 96.9842.000 x 23.250 x 24.000HD Segment LH 1.250 x 4.125
1076294 1 DB|| 4 2.75 3.56 3.56 230.00 104.3342.375 x 23.250 x 16.180Extra HD Segment 1.250 x 4.125
1076295 3 DB\\ 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment RH 1.250 x 4.125
1076296 3 DB// 4 6.09 3.94 3.94 247.00 112.0442.375 x 23.250 x 24.000Extra HD Segment LH 1.250 x 4.125
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
1957096CAST 1 DB|| 4 2.69 3.56 3.56 45.70 20.7321.250 x 9.625 x 16.000Bolt on Top Plate Center 1.250 x 5
1957097CAST 3 DB\\ 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate RH 1.250 x 5
1957098CAST 3 DB// 4 3.69 3.94 3.94 50.80 23.0421.250 x 9.625 x 20.250Bolt on Top Plate LH 1.250 x 5
1151548 2 IRR 124.50 56.471.375 x 16.000 x 25.000Weld-On Rear Wear Plate
1151549 1 IRR 90.00 40.821.375 x 10.000 x 28.543Weld-On Rear Wear Plate
992 G High Abrasion System1124197Serial Number:
1076764 1 SB\_/ 12Spade Nose Base Edge 3846.001744.522.750 x 36.457 x 190.551
1345906 2 IRRCorner LH/RH for 1U0740 Protectors
1U0740 4 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1006357 1 DB|| 6 2.75 6.00 6.00 211.00 95.7141.750 x 13.000 x 35.500Center Base Edge Wear Plate 1.000 x 3.75
1006356 2 DB|| 4 7.88 6.00 18.00 282.00 127.9141.750 x 13.000 x 45.750End Base Edge Wear Plate 1.000 x 3.75
1151549 1 IRR 90.00 40.821.375 x 10.000 x 28.543Weld-On Rear Wear Plate
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 98©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1151548 2 IRR 124.50 56.471.375 x 16.000 x 25.000Weld-On Rear Wear Plate
992 G High Abrasion SystemSerial Number:2085325 1 SB\_/Spade Nose Base Edge
1006357 3 DB|| 6 2.75 6.00 6.00 211.00 95.7161.750 x 13.000 x 35.500Base Edge Wear Plate 1.000 x 3.75
2755460 1 HA|| 4 2.76 3.54 3.54 185.60 84.1942.500 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755461 3 HA\\ 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755462 3 HA// 4 2.88 3.94 3.94 209.70 95.1242.500 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2755470 1 HA|| 4 2.76 3.54 3.54 239.60 108.6843.250 x 21.336 x 16.142HA Segment (Cast) 1.250 x 4.125
2755471 3 HA\\ 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment RH (Cast) 1.250 x 4.125
2755472 3 HA// 4 2.88 3.94 3.94 269.40 122.2043.250 x 21.336 x 17.165HA Segment LH (Cast) 1.250 x 4.125
2085327 1 4 2.66 3.56 3.56 48.70 22.091.250 x 10.250 x 16.000Bolt on Top Plate Center 1.250
2085328 3 54.40 24.68Bolt on Top Plate RH
2085329 3 54.50 24.72Bolt on Top Plate LH
992 B Modulok2V5034 3V2472Serial Number:
4T6543 2Center Base Edge Wear Plate
4T6542 5 DB|| 4 2.60 6.00 6.00 110.30 50.031.375 x 13.000 x 23.197End Base Edge Wear Plate 1.000
TEETH 9J550 Options
9K0071 2 DB||Rear Wear Plate
992 B Modulok9K4047Serial Number:
4T6540 3 DB|| 6 2.75 6.00 6.00 168.90 76.611.375 x 13.000 x 35.500Center Base Edge Wear Plate 1.000
4T6539 2 DB|| 5 2.81 6.00 6.00 140.90 63.911.375 x 13.000 x 29.625End Base Edge Wear Plate 1.000
TEETH 9J550 Options
992 C ModulokSerial Number:1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
4T6540 3 DB|| 6 2.75 6.00 6.00 168.90 76.611.375 x 13.000 x 35.500Center Base Edge Wear Plate 1.000
4T6541 2 DB|> 6 2.81 6.00 6.00 166.90 75.701.375 x 13.000 x 36.000End Base Edge Wear Plate 1.000
8J4974 3 DB|| 6 2.75 6.00 6.00 200.30 90.851.625 x 13.000 x 35.500HD Center Base Edge Wear Plate 1.000
9J6836 2 DB|> 6 2.81 6.00 6.00 206.00 93.441.625 x 13.000 x 36.000HD End Base Edge Wear Plate 1.000
TEETH 9J550 Options
992 C Modulok3V3254Serial Number:
4T6540 3 DB|| 6 2.75 6.00 6.00 168.90 76.611.375 x 13.000 x 35.500Center Base Edge Wear Plate 1.000
4T6541 2 DB|> 6 2.81 6.00 6.00 166.90 75.701.375 x 13.000 x 36.000End Base Edge Wear Plate 1.000
8J4974 3 DB|| 6 2.75 6.00 6.00 200.30 90.851.625 x 13.000 x 35.500HD Center Base Edge Wear Plate 1.000
9J6836 2 DB|> 6 2.81 6.00 6.00 206.00 93.441.625 x 13.000 x 36.000HD End Base Edge Wear Plate 1.000
TEETH 9J550 Options
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
992 C D Modulok5V5387 9V3013 9V0211 1061788 2Q3269Serial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 99©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9V0065BASE 1 SB\_/ 20Spade Nose Base Edge Without Holes 3431.001556.282.500 x 33.430 x 187.953
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
4T6540 3 DB|| 6 2.75 6.00 6.00 168.90 76.611.375 x 13.000 x 35.500Center Base Edge Wear Plate 1.000
4T6541 2 DB|> 6 2.81 6.00 6.00 166.90 75.701.375 x 13.000 x 36.000End Base Edge Wear Plate 1.000
8J4974 3 DB|| 6 2.75 6.00 6.00 200.30 90.851.625 x 13.000 x 35.500HD Center Base Edge Wear Plate 1.000
9J6836 2 DB|> 6 2.81 6.00 6.00 206.00 93.441.625 x 13.000 x 36.000HD End Base Edge Wear Plate 1.000
TEETH 9J550 Options
6W0276 2 DB|_| 4 1.31 36.00 122.30 55.4721.250 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
6Y3610 2 DB|_| 4 1.31 36.00 182.00 82.5521.750 x 13.000 x 38.625Rear Wear Plate 1.000 x 3.52 1.31 36.00 ...2nd Row1.000 x 3.5
1324712 2 DB|| 4 1.31 36.0021.750 x 13.000 x 38.625Hex Bolt Wear Plate 1.000 x 3.252 1.38 29.25 1.38 ...2nd Row1.000 x 3.25
994 - D Spade Nose Rock8X1491 8X0807 8X1497Serial Number:
8X0809 1 SB\_/ 40Spade Nose Base Edge 3.000 x 36.890 x 222.441
8X0813 1 IRRCorner no holes RH
8X0816 1 IRRCorner no holes LH
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1711704 3 ADPJ700 Weld-On Center Adapter 178.57 81.009.059 x 7.406 x 27.203
1711705 3 ADPJ700 Weld-On RH Adapter 177.91 80.709.059 x 7.406 x 27.203
1711706 3 ADPJ700 Weld-On LH Adapter 176.81 80.209.059 x 7.406 x 27.203
TEETH 9J700 Options
8E3157 2 DB|| 5 2.00 3.38 3.38 247.70 112.3552.000 x 27.500 x 17.500Segment 1.250 x 4.5
8E3158 3 DB\\ 5 5.31 3.38 3.38 257.60 116.8552.000 x 28.500 x 24.125Segment RH 1.250 x 4.5
8E3159 3 DB// 5 5.31 3.38 3.38 257.60 116.8552.000 x 28.500 x 24.125Segment LH 1.250 x 4.5
1004012 2 DB|| 5 2.00 3.38 3.38 352.00 159.6653.000 x 27.500 x 17.500HD Segment 1.250 x 4.5
1004013 3 DB\\ 5 5.31 3.38 3.38 390.00 176.9053.000 x 28.500 x 24.125HD Segment RH 1.250 x 4.5
1004014 3 DB// 5 5.31 3.38 3.38 390.00 176.9053.000 x 28.500 x 24.125HD Segment LH 1.250 x 4.5
8E3160 2 DB|| 4 1.81 43.38 1.81 480.00 217.7222.375 x 16.000 x 47.000Rear Wear Plate 1.250 x 4.52 1.81 43.38 1.81 ...2nd Row1.250 x 4.5
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Heavy Duty Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 4 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate 1.250 x 4.1252 1.81 43.38 1.81 ...2nd Row1.250 x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Weld-On Behind Heel Wear Plate 1.125
994 - D Spade Nose Rock1022598 1022606 1020673 1020676 1022124 1029319 1029326Serial Number:
1015868 1 SB\_/ 55Spade Nose Base Edge 4.000 x 27.780 x 222.441
1019373 1 IRRCorner no holes RH
1019374 1 IRRCorner no holes LH
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1031833 3 DB|| 5 2.06 3.35 3.35 290.40 131.7233.000 x 21.500 x 17.500Base Edge Wear Plate 1.250 x 4.125
6I8804 8 ADPJ800 Weld-On Adapter 218.03 98.9010.433 x 8.661 x 27.303
TEETH 8J800 Options
1031833 3 DB|| 5 2.06 3.35 3.35 290.40 131.7253.000 x 21.500 x 17.500Segment 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 100©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1031834 2 DB\\ 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.500 x 23.625Segment RH 1.250 x 4.125
1031835 2 DB// 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.750 x 23.625Segment LH 1.250 x 4.125
1099030 3 HA|| 5 1.97 3.35 3.35 354.30 160.7153.500 x 26.750 x 17.323HA Segment (Cast) 1.250 x 4.125
1099031 2 HA\\ 5 2.14 3.35 3.35 359.10 162.8953.500 x 27.478 x 17.323HA Segment RH (Cast) 1.250 x 4.125
1099032 2 HA// 5 2.14 3.35 3.35 359.10 162.8953.500 x 27.546 x 17.323HA Segment LH (Cast) 1.250 x 4.125
1957230 2 DB|| 5 2.05 3.35 3.35 84.40 38.281.500 x 13.059 x 17.500Bolt on Top Plate Center 1.250 x 7
1099031TP 3 DB\\ 5 2.32 3.35 3.35 94.60 42.911.500 x 13.750 x 17.652Bolt on Top Plate RH 1.250 x 7
1099032TP 3 DB// 5 2.32 3.35 3.35 94.60 42.911.500 x 13.750 x 17.652Bolt on Top Plate LH 1.250 x 7
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Heavy Duty Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 4 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate 1.250 x 4.1252 1.81 43.38 1.81 ...2nd Row1.250 x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Weld-On Behind Heel Wear Plate 1.125
994 - D Spade Nose Rock1134105 1134106 1134103 1117973 1117974 1134104 1134107 1134108Serial Number:
1102339 1 SB\_/Spade Nose Base Edge 4.000 x 32.677 x 222.441
1019373 1 IRRCorner no holes RH
1019374 1 IRRCorner no holes LH
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1073383 3 SB|| 5 4.25 3.38 3.38 369.00 167.3833.000 x 21.500 x 22.000Base Edge Wear Plate 1.250 x 4.125
6I8804 8 ADPJ800 Weld-On Adapter 218.03 98.9010.433 x 8.661 x 27.303
TEETH 8J800 Options
1073383 1 SB|| 5 4.25 3.38 3.38 369.00 167.3853.000 x 21.500 x 22.000Segment 1.250 x 4.125
1031834 3 DB\\ 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.500 x 23.625Segment RH 1.250 x 4.125
1031835 3 DB// 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.750 x 23.625Segment LH 1.250 x 4.125
1099033 1 HA|| 5 5.55 3.35 3.35 483.30 219.2253.500 x 26.750 x 24.488HA Segment (Cast) 1.250 x 4.125
1099031 3 HA\\ 5 2.14 3.35 3.35 359.10 162.8953.500 x 27.478 x 17.323HA Segment RH (Cast) 1.250 x 4.125
1099032 3 HA// 5 2.14 3.35 3.35 359.10 162.8953.500 x 27.546 x 17.323HA Segment LH (Cast) 1.250 x 4.125
1099033TP 1 DB|| 5 5.55 3.35 3.35 122.30 55.471.500 x 13.059 x 24.500Bolt on Top Plate Center 1.250 x 7
1099031TP 3 DB\\ 5 2.32 3.35 3.35 94.60 42.911.500 x 13.750 x 17.652Bolt on Top Plate RH 1.250 x 7
1099032TP 3 DB// 5 2.32 3.35 3.35 94.60 42.911.500 x 13.750 x 17.652Bolt on Top Plate LH 1.250 x 7
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Heavy Duty Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 4 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate 1.250 x 4.1252 1.81 43.38 1.81 ...2nd Row1.250 x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Weld-On Behind Heel Wear Plate 1.125
994 - D F Spade Nose Rock1212360 1212361 1442844 2573683 2573685 2573687 2573689Serial Number:
1212105 1 SB\_/ 65Spade Nose Base Edge 4.000 x 39.370 x 222.441
1073383 5 SB|| 5 4.25 3.38 3.38 369.00 167.3833.000 x 21.500 x 22.000Base Edge Wear Plate 1.250 x 4.125
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
6I8804 8 ADPJ800 Weld-On Adapter 218.03 98.9010.433 x 8.661 x 27.303
TEETH 8J800 Options
1073383 1 SB|| 5 4.25 3.38 3.38 369.00 167.3853.000 x 21.500 x 22.000Segment 1.250 x 4.125
1031834 3 DB\\ 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.500 x 23.625Segment RH 1.250 x 4.125
1031835 3 DB// 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.750 x 23.625Segment LH 1.250 x 4.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 101©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1099033 1 HA|| 5 5.55 3.35 3.35 483.30 219.2253.500 x 26.750 x 24.488HA Segment (Cast) 1.250 x 4.125
1176805 3 HA\\ 5 2.20 3.35 3.35 351.00 159.2153.500 x 26.750 x 17.323HA Segment RH (Cast) 1.250 x 4.125
1176806 3 HA// 5 2.20 3.35 3.35 351.00 159.2153.500 x 26.750 x 17.323HA Segment LH (Cast) 1.250 x 4.125
1099033TP 1 DB|| 5 5.55 3.35 3.35 122.30 55.471.500 x 13.059 x 24.500Bolt on Top Plate Center 1.250 x 7
1957231 3 DB\\ 5 2.07 3.35 3.35 93.00 42.181.500 x 13.500 x 17.101Bolt on Top Plate RH 1.250 x 7
1957232 3 DB// 5 2.07 3.35 3.35 93.00 42.181.500 x 13.500 x 17.101Bolt on Top Plate LH 1.250 x 7
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Heavy Duty Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 4 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate 1.250 x 4.1252 1.81 43.38 1.81 ...2nd Row1.250 x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Weld-On Behind Heel Wear Plate 1.125
994 - D General Purpose1029333Serial Number:
1029914 1 WOSBBase Edge With Segment Holes 5100.002313.324.000 x 22.323 x 222.441
1016777 2 IRRCorner LH/RH for 1250800 Protectors
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
TEETH 8J700 Options
8E3157 7 DB|| 5 2.00 3.38 3.38 247.70 112.3552.000 x 27.500 x 17.500Segment 1.250 x 4.5
1004012 7 DB|| 5 2.00 3.38 3.38 352.00 159.6653.000 x 27.500 x 17.500HD Segment 1.250 x 4.5
8E3160 2 DB|| 4 1.81 43.38 1.81 480.00 217.7222.375 x 16.000 x 47.000Rear Wear Plate 1.250 x 4.52 1.81 43.38 1.81 ...2nd Row1.250 x 4.5
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Heavy Duty Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate x 4.1252 1.81 43.38 1.81 ...2nd Row x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Weld-On Behind Heel Wear Plate 1.125
994 - D Spade Nose Rock1141992 1022570 1022593 1020633 1019704 1020641 1020649 1029300 1029302Serial Number:
1015865 1 SB\_/ 60Spade Nose Base Edge 4.000 x 32.673 x 244.882
1019373 1 IRRCorner no holes RH
1019374 1 IRRCorner no holes LH
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1073383 2 SB|| 5 4.25 3.38 3.38 369.00 167.3833.000 x 21.500 x 22.000Center Base Edge Wear Plate 1.250 x 4.125
1031834 1 DB\\ 5 3.69 3.38 3.38 308.90 140.1133.000 x 21.500 x 23.625End Base Edge Wear Plate 1.250 x 4.125
1031835 1 DB// 5 3.69 3.38 3.38 308.90 140.1133.000 x 21.750 x 23.625End Base Edge Wear Plate 1.250 x 4.125
6I8804 9 ADPJ800 Weld-On Adapter 218.03 98.9010.433 x 8.661 x 27.303
TEETH 9J800 Options
1031833 2 DB|| 5 2.06 3.35 3.35 290.40 131.7253.000 x 21.500 x 17.500Segment 1.250 x 4.125
1031834 3 DB\\ 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.500 x 23.625Segment RH 1.250 x 4.125
1031835 3 DB// 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.750 x 23.625Segment LH 1.250 x 4.125
1099030 2 HA|| 5 1.97 3.35 3.35 354.30 160.7153.500 x 26.750 x 17.323HA Segment (Cast) 1.250 x 4.125
1099031 3 HA\\ 5 2.14 3.35 3.35 359.10 162.8953.500 x 27.478 x 17.323HA Segment RH (Cast) 1.250 x 4.125
1099032 3 HA// 5 2.14 3.35 3.35 359.10 162.8953.500 x 27.546 x 17.323HA Segment LH (Cast) 1.250 x 4.125
1957230 2 DB|| 5 2.05 3.35 3.35 84.40 38.281.500 x 13.059 x 17.500Bolt on Top Plate Center 1.250 x 7
1099031TP 3 DB\\ 5 2.32 3.35 3.35 94.60 42.911.500 x 13.750 x 17.652Bolt on Top Plate RH 1.250 x 7
1099032TP 3 DB// 5 2.32 3.35 3.35 94.60 42.911.500 x 13.750 x 17.652Bolt on Top Plate LH 1.250 x 7
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 102©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Heavy Duty Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate x 4.1252 1.81 43.38 1.81 ...2nd Row x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Weld-On Behind Heel Wear Plate 1.125
994 - D F Spade Nose Rock1218889 1218890 2514561 2513691Serial Number:
1216660 1 SB\_/ 65Spade Nose Base Edge 4.000 x 39.370 x 244.882
1019373 1 IRRCorner no holes RH
1019374 1 IRRCorner no holes LH
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1073383 5 SB|| 5 4.25 3.38 3.38 369.00 167.3833.000 x 21.500 x 22.000Center Base Edge Wear Plate 1.250 x 4.125
6I8804 9 ADPJ800 Weld-On Adapter 218.03 98.9010.433 x 8.661 x 27.303
TEETH 9J800 Options
1031833 2 DB|| 5 2.06 3.35 3.35 290.40 131.7253.000 x 21.500 x 17.500Segment 1.250 x 4.125
1031834 3 DB\\ 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.500 x 23.625Segment RH 1.250 x 4.125
1031835 3 DB// 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.750 x 23.625Segment LH 1.250 x 4.125
1099030 2 HA|| 5 1.97 3.35 3.35 354.30 160.713.500 x 26.750 x 17.323HA Segment (Cast) 1.250
1176805 3 HA\\ 5 2.20 3.35 3.35 351.00 159.2153.500 x 26.750 x 17.323HA Segment RH (Cast) 1.250 x 4.125
1176806 3 HA// 5 2.20 3.35 3.35 351.00 159.2153.500 x 26.750 x 17.323HA Segment LH (Cast) 1.250 x 4.125
1957230 2 DB|| 5 2.05 3.35 3.35 84.40 38.2851.500 x 13.059 x 17.500Bolt on Top Plate Center 1.250 x 7
1957231 3 DB\\ 5 2.07 3.35 3.35 93.00 42.181.500 x 13.500 x 17.101Bolt on Top Plate RH 1.250 x 7
1957232 3 DB// 5 2.07 3.35 3.35 93.00 42.181.500 x 13.500 x 17.101Bolt on Top Plate LH 1.250 x 7
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Heavy Duty Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate x 4.1252 1.81 43.38 1.81 ...2nd Row x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Weld-On Behind Heel Wear Plate 1.125
994 - D F General Purpose1016756 1565963 2573692Serial Number:
1016776 1 WOSBBase Edge With Segment Holes 5600.002540.124.000 x 21.142 x 244.882
1016777 2 IRRCorner LH/RH for 1250800 Protectors
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
TEETH 9J700 Options
8E3157 8 DB|| 5 2.00 3.38 3.38 247.70 112.3552.000 x 27.500 x 17.500Segment 1.250 x 4.5
1099030 8 HA|| 5 1.97 3.35 3.35 354.30 160.713.500 x 26.750 x 17.323HA Segment (Cast) 1.250
1004012 8 DB|| 5 2.00 3.38 3.38 352.00 159.6653.000 x 27.500 x 17.500HD Segment 1.250 x 4.5
1957230 8 DB|| 5 2.05 3.35 3.35 84.40 38.281.500 x 13.059 x 17.500Bolt on Top Plate Center 1.250
8E3160 2 DB|| 4 1.81 43.38 1.81 480.00 217.7222.375 x 16.000 x 47.000Rear Wear Plate 1.250 x 4.52 1.81 43.38 1.81 ...2nd Row1.250 x 4.5
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Heavy Duty Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate x 4.1252 1.81 43.38 1.81 ...2nd Row x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Weld-On Behind Heel Wear Plate 1.125
994 F Spade Nose Rock2514560Serial Number:
1216660 1 SB\_/ 65Spade Nose Base Edge 4.000 x 39.370 x 244.882
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 103©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
1U0740 2 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1073383 5 SB|| 5 4.25 3.38 3.38 369.00 167.3833.000 x 21.500 x 22.000Center Base Edge Wear Plate 1.250 x 4.125
6I8804 9 ADPJ800 Weld-On Adapter 218.03 98.9010.433 x 8.661 x 27.303
TEETH 9J800 Options
1031833 2 DB|| 5 2.06 3.35 3.35 290.40 131.7253.000 x 21.500 x 17.500Segment 1.250 x 4.125
1031834 3 DB\\ 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.500 x 23.625Segment RH 1.250 x 4.125
1031835 3 DB// 5 3.69 3.38 3.38 308.90 140.1153.000 x 21.750 x 23.625Segment LH 1.250 x 4.125
1099030 2 HA|| 5 1.97 3.35 3.35 354.30 160.713.500 x 26.750 x 17.323HA Segment (Cast) 1.250
1176805 3 HA\\ 5 2.20 3.35 3.35 351.00 159.2153.500 x 26.750 x 17.323HA Segment RH (Cast) 1.250 x 4.125
1176806 3 HA// 5 2.20 3.35 3.35 351.00 159.2153.500 x 26.750 x 17.323HA Segment LH (Cast) 1.250 x 4.125
1957230 2 DB|| 5 2.05 3.35 3.35 84.40 38.2851.500 x 13.059 x 17.500Bolt on Top Plate Center 1.250 x 7
1957231 3 DB\\ 5 2.07 3.35 3.35 93.00 42.181.500 x 13.500 x 17.101Bolt on Top Plate RH 1.250 x 7
1957232 3 DB// 5 2.07 3.35 3.35 93.00 42.181.500 x 13.500 x 17.101Bolt on Top Plate LH 1.250 x 7
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Heavy Duty Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate x 4.1252 1.81 43.38 1.81 ...2nd Row x 4.125
1441281 2 IRR 3 3.63 6.50 158.40 71.853.000 x 18.000 x 14.500Bolt-On Behind Heel Wear Plate 1.5003.63 ...2nd Row1.500
1441282 2 IRR 3 3.63 6.50 158.40 71.853.000 x 18.000 x 14.500Bolt-On Behind Heel Wear Plate 1.5003.63 ...2nd Row1.500
994 Modulok1020672 1022597 1022605 1020663 1020675 1022123 1177693 1177694 1177695 1177696 1177697 1177698Serial Number:
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
9W4493 4 DB|| 9 2.13 3.00 3.00 400.40 181.6262.375 x 16.000 x 40.250Center Base Edge Wear Plate 1.250 x 4.125
1042001 2 SE|> 6 3.16 6.03 6.00 237.30 107.6432.500 x 12.125 x 29.625End Base Edge Wear Plate 1.250 x 4.1253.16 6.03 6.00 ...2nd Row1.250 x 0
TEETH 8J800 Options
8E3160 2 DB|| 4 1.81 43.38 1.81 480.00 217.7222.375 x 16.000 x 47.000Rear Wear Plate 1.250 x 4.52 1.81 43.38 1.81 ...2nd Row1.250 x 4.5
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Rear Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
1324714 2 DB|| 4 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate 1.250 x 4.1252 1.81 43.38 1.81 ...2nd Row1.250 x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Rear Wear Plate 1.125
994 - D Modulok1020632 1020639 1022505 1022592 1020640 1020648Serial Number:
1250800 2 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
9W4493 3 DB|| 9 2.13 3.00 3.00 400.40 181.6262.375 x 16.000 x 40.250Center Base Edge Wear Plate 1.250 x 4.125
6Y0022 2 DB|> 7 3.25 3.00 3.00 293.20 132.9942.375 x 16.000 x 30.875Center Base Edge Wear Plate 1.250 x 4.125
1042001 2 SE|> 6 3.16 6.03 6.00 237.30 107.6432.500 x 12.125 x 29.625End Base Edge Wear Plate 1.250 x 4.1253.16 6.03 6.00 ...2nd Row1.250 x 0
TEETH 8J800 Options
8E3160 2 DB|| 4 1.81 43.38 1.81 480.00 217.7222.375 x 16.000 x 47.000Rear Wear Plate 1.250 x 4.52 1.81 43.38 1.81 ...2nd Row1.250 x 4.5
1004015 2 DB|| 4 1.81 43.38 511.50 232.0123.000 x 14.750 x 47.000Rear Wear Plate 1.250 x 4.52 1.81 43.38 ...2nd Row1.250 x 4.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 104©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loaders
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1324714 2 DB|| 4 1.81 43.38 1.812 x x 47.000Hex Bolt Wear Plate 1.250 x 4.1252 1.81 43.38 1.81 ...2nd Row1.250 x 4.125
2A6724 4 IRR 3 4.00 4.00 4.00 31.00 14.060.750 x 17.625 x 14.500Rear Wear Plate 1.125
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 105©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loader Backhoes
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
416 420 424 426 428 430 432 436 438 442 88" Bucket9R1220 9R1219 9R5989 9R0088 9R4488 9R0089Serial Number:
9R0316 1 WOSBBase Edge Without Holes 135.00 61.230.750 x 8.000 x 88.250
416 420 424 426 428 430 432 436 438 442 89" Bucket9R5201 9R5988 9R5989Serial Number:
9R4672 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 99.70 45.220.750 x 6.000 x 89.055
9R5205 1 IRRCorner no holes RH 5.80 2.630.750 x 6.000 x 5.563
9R5206 1 IRRCorner no holes LH 5.80 2.630.750 x 6.000 x 5.563
9W8215 2 DB|| 4 5.75 11.81 11.81 70.00 31.7540.750 x 8.000 x 44.500Center 0.625 x 2.25
TEETH 8J200 Options
416 420 424 426 428 430 432 436 438 442 89" Multi-Puprose Buck9R5427 9R3732 1083036 9R3733 9R4667 9R6088Serial Number:
9R4672 1 WOSB 16Base Edge For Bolt-on Edges or Teeth 99.70 45.220.750 x 6.000 x 89.055
9R4674 2 IRRCorner RH/LH 5.00 2.270.750 x 5.875 x 5.813
9W8215 2 DB|| 4 5.75 11.81 11.81 70.00 31.7540.750 x 8.000 x 44.500Center 0.625 x 2.25
TEETH 8J200 Options
9R4670 1 SB|| 48.10 21.820.500 x 3.937 x 89.055Multi purpose dozer center
1257116 1 SE|| 47.20 21.410.500 x 3.937 x 85.945Mult purpose clam edge
2333757 SE|| 8 3.25 11.81 8.81 74.50 33.790.750 x 4.000 x 89.125Multi purpose dozer edge 0.625
416 420 424 426 428 430 432 436 438 442 94" General Purpose Bu9R5202 1121931 1121933 1181971 1181984Serial Number:
9R5313 1 WOSB 16Base Edge Without Holes 106.10 48.130.750 x 6.000 x 94.724
9R5205 1 IRRCorner no holes RH 5.80 2.630.750 x 6.000 x 5.563
9R5206 1 IRRCorner no holes LH 5.80 2.630.750 x 6.000 x 5.563
1187110 2 DB|| 4 5.94 12.00 12.00 74.10 33.6140.750 x 8.000 x 47.875Center 0.625 x 2.25
TEETH 8J200 Options
416 420 424 426 428 430 432 436 438 442 94" Multi-Puprose Buck9R5787 9R5789 1043964 1043965Serial Number:
9R5313 1 WOSB 16Base Edge Without Holes 106.10 48.130.750 x 6.000 x 94.724
9R4674 2 IRRCorner RH/LH 5.00 2.270.750 x 5.875 x 5.813
1187110 2 DB|| 4 5.94 12.00 12.00 74.10 33.6140.750 x 8.000 x 47.875Center 0.625 x 2.25
TEETH 8J200 Options
9R5786 1 SB|| 51.20 23.220.500 x 3.937 x 94.724Multi purpose dozer center
1257117 1 SE|| 50.50 22.910.500 x 3.937 x 92.008Mult purpose clam edge
2330859 SE|| 5.25 12.00 9.75 x x 94.750Multi purpose dozer edge
446 95" General Purpose Bucket9R3088 9R9766Serial Number:
9R4101 1 WOSBBase Edge
9U9665 2 DB|| 12 1.94 4.00 4.00 93.10 42.23120.750 x 10.000 x 48.125Center 0.625 x 2.25
446 95" Multi-Puprose Bucket6Q0655Serial Number:
6Q2193 1 WOSB 8Base Edge 207.20 93.981.000 x 8.000 x 97.240
6Q2197 1 IRRCorner no holes RH 11.00 4.991.000 x 7.870 x 6.100
6Q2196 1 IRRCorner no holes LH 11.00 4.991.000 x 7.870 x 6.100
9U9665 2 DB|| 12 1.94 4.00 4.00 93.10 42.2340.750 x 10.000 x 48.125Center 0.625 x 2.25
1747982 2 DB|| 4 5.87 12.00 12.00 96.70 43.8640.750 x 10.000 x 49.291Longer Center 0.625 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Loader Backhoes
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
6Q2191PB 1 DB|| 14 1.97 7.09 7.09 71.40 32.39140.625 x 4.921 x 96.063Multi purpose dozer center 0.500 x 2
6Q2191 1 DB|| 14 1.96 7.08 7.08 71.70 32.52140.625 x 4.920 x 96.060Multi purpose dozer center (Flat Head Sc 0.500 x 2
6Q2194 1 SE|| 65.40 29.660.625 x 3.937 x 93.858Mult purpose clam edge
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Skid Steers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
216 226 232 236 242 246 248 252 262 268 54" BUCKETSN/ASerial Number:
1495434 1 WOSB 6Base Edge 59.00 26.760.625 x 6.000 x 55.945
1359393 1 DB|| 6 2.79 10.07 10.07 47.00 21.3260.625 x 6.500 x 56.000Bolt On (Flat Head Screws) 0.688 x 2
1359393PB 1 DB|| 6 2.79 10.07 10.07 47.00 21.3260.620 x 6.500 x 56.000Bolt On (Plow Bolts) 0.625 x 2
1747965 1 DB|| 6 2.80 10.08 10.08 71.00 32.2160.625 x 8.000 x 56.000Wider Bolt On (Plow Bolts) 0.625 x 2
1747971 1 DB|| 6 2.80 10.08 10.08 86.00 39.0160.750 x 8.000 x 56.000Thicker/Wider Bolt On (Plow Bolts) 0.625 x 2
216 226 232 236 242 246 248 252 262 268 60" BUCKETSN/ASerial Number:
1495435 1 WOSB 16Base Edge 68.50 31.070.750 x 6.000 x 62.008
1359394 1 DB|| 8 2.87 8.11 8.11 63.10 28.6280.625 x 6.500 x 62.520Bolt On (Flat Head Screws) 0.688 x 2
1359394PB 1 DB|| 8 2.87 8.11 8.11 65.00 29.4880.625 x 6.500 x 62.520Bolt On (Plow Bolts) 0.625 x 2
1747966 1 DB|| 8 2.87 8.11 8.11 79.00 35.8380.625 x 8.000 x 62.500Wider Bolt On (Plow Bolts) 0.625 x 2
1747972 1 DB|| 8 2.87 8.11 8.11 96.00 43.5480.750 x 8.000 x 62.520Thicker/Wider Bolt On (Plow Bolts) 0.625 x 2
216 226 232 236 242 246 248 252 262 268 66" BUCKETSN/ASerial Number:
1495436 1 WOSB 16Base Edge 75.00 34.020.750 x 6.000 x 68.125
1359395 1 DB|| 8 2.81 9.00 9.00 68.90 31.2580.625 x 6.500 x 68.625Bolt On (Flat Head Screws) 0.688 x 2
1359395PB 1 DB|| 8 2.81 9.00 9.00 69.40 31.4880.625 x 6.500 x 68.625Bolt On (Plow Bolts) 0.625 x 2
1747967 1 DB|| 8 2.81 9.00 9.00 87.00 39.4680.625 x 8.000 x 68.625Wider Bolt On (Plow Bolts) 0.625 x 2
1747973 1 DB|| 8 2.81 9.00 9.00 106.00 48.0880.750 x 8.000 x 68.625Thicker/Wider Bolt On (Plow Bolts) 0.625 x 2
216 226 232 236 242 246 248 252 262 268 72" BUCKETSN/ASerial Number:
1495437 1 WOSB 22Base Edge 82.20 37.290.750 x 6.000 x 74.409
1359396 1 DB|| 11 2.95 4.90 9.80 75.00 34.02110.625 x 6.500 x 74.528Bolt On (Flat Head Screws) 0.688 x 2
1359396PB 1 DB|| 11 2.95 4.90 9.80 75.00 34.02110.625 x 6.500 x 74.528Bolt On (Plow Bolts) 0.625 x 2
1747968 1 DB|| 11 2.95 4.90 9.80 95.60 43.36110.625 x 8.000 x 74.528Wider Bolt On (Plow Bolts) 0.625 x 2
1747974 1 DB|| 11 2.95 4.90 9.80 116.30 52.75110.750 x 8.000 x 74.528Thicker/Wider Bolt On (Plow Bolts) 0.625 x 2
216 226 232 236 242 246 248 252 262 268 78" BUCKETSN/ASerial Number:
1647433 1 WOSB 17Base Edge For Bolt-on Edges Only 89.00 40.370.750 x 6.000 x 80.157
1997722 1 SB|| 24Base Edge For Bolt-on Edges or Teeth 88.80 40.280.750 x 6.000 x 80.157
1359397 1 DB|| 11 2.96 4.65 4.65 80.07 36.32110.625 x 6.500 x 80.579Bolt On (Flat Head Screws) 0.688 x 2
1359397PB 1 DB|| 11 2.96 4.65 4.65 81.40 36.92110.625 x 6.500 x 80.579Bolt On (Plow Bolts) 0.625 x 2
1747969 1 DB|| 11 2.96 4.67 4.67 102.00 46.27110.625 x 8.000 x 80.579Wider Bolt On (Plow Bolts) 0.625 x 2
1747975 1 DB|| 11 2.96 4.67 4.67 124.00 56.25110.750 x 8.000 x 80.579Thicker/Wider Bolt On (Plow Bolts) 0.625 x 2
216 226 232 236 242 246 248 252 262 268 85" BUCKETSN/ASerial Number:
2293432 SB||Base Edge
1955124 1 DB|| 11 3.15 6.69 6.69 86.80 39.37110.625 x 6.500 x 86.614Bolt On (Flat Head Screws) 0.625 x 2
1955124PB 1 DB|| 11 3.15 6.69 6.69 86.90 39.420.625 x 6.500 x 86.614Bolt On (Plow Bolts) 0.625
1747976 1 DB|| 7 3.15 13.39 13.39 136.00 61.690.750 x 8.000 x 86.614Thicker/Wider Bolt On (Plow Bolts) 0.625
216 226 232 236 242 246 248 252 262 268 96" BUCKETSSerial Number:2929257 1 SB||Base Edge
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Skid Steers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2967680 1 DB|| 130.625 x 6.500 x 98.543Bolt On (Flat Head Screws) 0.625
216 226 232 236 242 246 248 252 262 268 72" DOZERN/ASerial Number:
1359396 1 DB|| 11 2.95 4.90 9.80 75.00 34.020.625 x 6.500 x 74.528Center 0.688
216 226 232 236 242 246 248 252 262 268 81.5" DOZERN/ASerial Number:
1495740 1 70.500 x 8.000 x 87.000Center 0.625
216 226 232 236 242 246 248 252 262 268 90.5" DOZERN/ASerial Number:
1433088 1 x x 64.173Center
1590372 2 x x 13.386Level Cut End Bit LH/RH
216 226 232 236 242 246 248 252 262 268 94.4" DOZERN/ASerial Number:
1433089 1 x x 68.110Center
1957193 2 x x 14.370Level Cut End Bit LH/RH
216 226 232 236 242 246 248 252 262 268 BP15 PICKUP BROOM62"Serial Number:
1359394 1 DB|| 8 2.87 8.11 8.11 63.10 28.620.625 x 6.500 x 62.520Bolt On (Flat Head Screws) 0.688
1359394PB 1 DB|| 8 2.87 8.11 8.11 65.00 29.480.625 x 6.500 x 62.520Bolt On (Plow Bolts) 0.625
216 226 232 236 242 246 248 252 262 268 BP18 PICKUP BROOM74.5"Serial Number:
1359396 1 DB|| 11 2.95 4.90 9.80 75.00 34.020.625 x 6.500 x 74.528Bolt On (Flat Head Screws) 0.688
1359396PB 1 DB|| 11 2.95 4.90 9.80 75.00 34.020.625 x 6.500 x 74.528Bolt On (Plow Bolts) 0.625
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Telehandler
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
TH63 Serial Number:4003 1 SB|| 12Base Edge For Bolt-on Edges Only 196.00 88.901.000 x 8.000 x 96.000
9R5320 2 DB|| 6 5.94 4.00 8.00 56.30 25.540.750 x 6.000 x 47.875Center 0.625
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Excavator
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
Serial Number:
--> E180, E200, EL200, 215 and 219 Bucket
9J1855 IRR 7 25.00 11.34Combination Side Cutter RH 0.750
9J1856 IRR 7 25.00 11.34Combination Side Cutter LH 0.750
4T2963 IRR 4 1.38 2.75 2.75 16.00 7.260.625 x 8.000 x 15.250Extension Blade RH 0.625
4T2964 IRR 4 1.38 2.75 2.75 16.00 7.260.625 x 8.000 x 15.250Extension Blade LH 0.625
9J1857 HAIRR 2 6.25 6.31 18.60 8.440.875 x 8.000 x 12.875Strike-Off RH 0.750
9J1858 HAIRR 2 1.13 6.31 18.60 8.440.875 x 8.000 x 12.875Strike-Off LH 0.750
--> 315 Buckets
0964747 IRR 4 5.75 31.70 14.382.250 x 11.412 x 17.607One Piece Side Cutter LH 1.0636.13 ...2nd Row1.063
0964748 IRR 4 5.75 31.70 14.382.250 x 11.412 x 17.607One Piece Side Cutter RH 1.0636.13 ...2nd Row1.063
--> S, B, C and D Family Buckets
7Y0357 IRR 3 39.60 17.962.500 x 15.250 x 16.500One Piece Side Cutter RH 1.1253.94 3.94 ...2nd Row1.125
7Y0358 IRR 3 39.60 17.962.500 x 15.250 x 16.500One Piece Side Cutter LH 1.1253.94 3.94 ...2nd Row1.125
2322147 IRR 4 2.84 3.94 3.94 54.00 24.491.125 x 10.000 x 19.297Heavy Duty Side Cutter RH 1.125
2322148 IRR 4 2.84 3.94 3.94 55.40 25.131.125 x 10.000 x 19.297Heavy Duty Side Cutter LH 1.125
8J9614 IRR 7 4.40 6.54 8.60 50.50 22.91Combination Side Cutter LH 1.000
8J9615 IRR 7 51.10 23.18Combination Side Cutter RH 1.000
4T2886 DB/\ 4 4.50 3.00 3.00 32.00 14.510.750 x 10.000 x 18.000Extension Blade 0.750
2322140 HAIRR 3 2.81 3.94 3.94 56.20 25.493.813 x 15.237 x 19.237Strike-Off RH 1.125
1748044 HAIRR 3 2.81 3.94 3.94 55.60 25.223.813 x 15.237 x 19.237Strike-Off LH 1.125
--> E, F, G, H and J Family Buckets
8J9825 IRR 9 4.00 69.00 31.302.000 x 15.813 x 19.188Combination Side Cutter LH 1.0008.00 ...2nd Row1.000
8J9826 IRR 9 4.00 69.00 31.302.000 x 15.813 x 19.188Combination Side Cutter RH 1.0008.00 ...2nd Row1.000
4T6664 DB/\ 4 7.25 3.00 3.00 63.00 28.581.000 x 10.000 x 23.500Extension Blade 1.000
8J5188 HAIRR 2 9.88 4.00 107.00 48.531.125 x 10.000 x 23.750Strike-Off 1.000
2568690 5 93.90 42.595.033 x 17.663 x 25.184Heavy Duty Side Cutter RH 1.125
2568691 5 93.90 42.595.033 x 17.663 x 25.184Heavy Duty Side Cutter LH 1.125
1122489 IRR 2Sidebar Protector 38.70 17.551.375 x 6.813 x 17.125
1662877 IRR 2Sidebar Protector 40.50 18.371.563 x 6.750 x 18.125
1U0740 IRR 2Sidebar Protector 55.60 25.222.125 x 6.313 x 23.813
1122494 IRR 2Sidebar Protector 77.30 35.061.625 x 8.000 x 37.000
1250800 IRR 2Sidebar Protector 121.60 55.162.750 x 8.500 x 40.000
7T5140 20.60 9.34Step
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
10 19CSerial Number:
4T6625 1 DB|| 14 3.13 6.00 6.00 122.10 55.3870.875 x 13.000 x 42.250Drop Center 0.875 x 2.53.13 6.00 6.00 ...2nd Row0.875 x 0
4T2940 1 DB|| 7 3.13 6.00 6.00 77.00 34.9370.750 x 10.000 x 42.250Level Cut Center 0.875 x 2.5
4T2953 2 DB|| 4 2.75 6.00 6.00 48.00 21.7740.750 x 10.000 x 24.500End 0.875 x 2.5
4T2939 1 DB|| 15 3.38 6.00 6.00 180.00 81.65150.750 x 10.000 x 90.750Optional One Piece Edge 0.875 x 2.5
9F1831 2 SE|| 4 2.03 2.48 4.66 19.50 8.8540.625 x 8.000 x 14.000Router Bit 0.688 x 2
10 CURVED BOTTOM 3CSerial Number:
4T6626 1 DB|| 16 1.50 3.50 3.50 163.90 74.3480.875 x 13.000 x 55.500Drop Center 0.750 x 2.25
4T2882 1 DB|| 16 1.50 3.50 3.50 108.40 49.1780.750 x 10.000 x 55.500Level Cut Center 0.750 x 2.25
4T2883 2 DB|| 6 1.38 3.50 3.50 40.00 18.1460.750 x 10.000 x 20.250End 0.750 x 2.25
4T8807 1 DB|| 6 1.31 3.50 3.50 50.10 22.7260.875 x 12.000 x 20.125Wider Level Cut End RH 0.750 x 2.25
4T8808 1 DB|| 6 1.31 3.50 3.50 50.10 22.7260.875 x 12.000 x 20.125Wider Level Cut End LH 0.750 x 2.25
8F7232 2 SE|| 5 2.50 3.50 3.50 26.60 12.0750.750 x 8.000 x 16.000Router Bit 0.813 x 2.25
D22506 1 SE|| 28 1.63 3.50 3.500.750 x 6.500 x 96.750Straight Blade Support 0.813
15 4W 92DSerial Number:
4T6627 1 DB|| 18 3.13 6.00 6.00 156.80 71.1290.875 x 13.000 x 54.250Drop Center 0.875 x 2.53.13 6.00 6.00 ...2nd Row0.875 x 0
4T2941 1 DB|| 9 3.13 6.00 6.00 104.00 47.1790.750 x 10.000 x 54.250Level Cut Center 0.875 x 2.5
4T2942 2 DB|| 4 2.75 6.00 6.00 40.00 18.1440.750 x 10.000 x 23.500End 0.875 x 2.5
4T2947 1 DB|| 17 2.69 6.00 6.00 209.00 94.80170.750 x 10.000 x 101.375Optional One Piece Edge 0.875 x 2.5
8F7232 2 SE|| 5 2.50 3.50 3.50 26.60 12.0750.750 x 8.000 x 16.000Router Bit 0.813 x 2.25
20 21 8J 11CSerial Number:
4T6565 1 DB|| 18 3.13 6.00 6.00 192.30 87.2390.875 x 16.000 x 54.250Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
4T6617 1 DB|| 9 3.13 6.00 6.00 159.10 72.1790.875 x 13.000 x 54.250Level Cut Center 1.000 x 3
4T6612 2 DB|| 5 2.75 6.00 6.00 86.40 39.1950.875 x 13.000 x 29.500End 1.000 x 3
4T2900 1 DB|| 18 3.13 6.00 6.00 250.90 113.8191.125 x 16.000 x 54.250HD Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
4T6380 2 DB|| 5 2.75 6.00 6.00 113.60 51.5351.125 x 13.000 x 29.500HD End 1.000 x 3
8F7232 2 SE|| 5 2.50 3.50 3.50 26.60 12.0750.750 x 8.000 x 16.000Router Bit 0.813 x 2.5
6F3319 1 IRR 5 2.50 2.48 3.47 45.00 20.411.000 x 8.750 x 22.875RH Router Bit Support 0.750
6F3320 1 IRR 5 2.50 2.48 3.47 45.00 20.411.000 x 8.750 x 22.875LH Router Bit Support 0.750
40 1WSerial Number:
4T2874 1 DB|| 20 2.13 4.00 4.00 70.00 31.75100.750 x 10.000 x 40.250Drop Center 0.750 x 22.13 4.00 4.00 ...2nd Row0.750 x 0
4T2962 1 DB|| 10 2.13 4.00 4.00 49.00 22.2350.750 x 8.000 x 40.250Level Cut Center 0.750 x 2
4T2965 2 DB|| 4 1.75 4.00 4.00 19.00 8.6240.625 x 8.000 x 15.500End 0.750 x 2
60 CURVED BOTTOM 1DSerial Number:
4T2881 1 DB|| 14 1.75 3.50 3.50 95.70 43.41140.750 x 10.000 x 49.000Center 0.750 x 2.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T2884 2 DB|| 5 1.69 3.50 3.50 34.00 15.4250.750 x 10.000 x 17.375End 0.750 x 2.25
4T8833 1 DB|| 5 1.69 3.50 3.50 44.70 20.2850.875 x 12.000 x 17.375Wider Level Cut End RH 0.750 x 2.25
4T8834 1 DB|| 5 1.69 3.50 3.50 44.70 20.2850.875 x 12.000 x 17.375Wider Level Cut End LH 0.750 x 2.25
9F1831 2 SE|| 4 2.03 2.48 4.66 19.50 8.8540.625 x 8.000 x 14.000Router Bit 0.688 x 2
60 2WSerial Number:
4T6625 1 DB|| 14 3.13 6.00 6.00 122.10 55.3870.875 x 13.000 x 42.250Drop Center 0.875 x 2.53.13 6.00 6.00 ...2nd Row0.875 x 0
4T2940 1 DB|| 7 3.13 6.00 6.00 77.00 34.9370.750 x 10.000 x 42.250Level Cut Center 0.875 x 2.5
4T2953 2 DB|| 4 2.75 6.00 6.00 48.00 21.7740.750 x 10.000 x 24.500End 0.875 x 2.5
4T2939 1 DB|| 15 3.38 6.00 6.00 180.00 81.65150.750 x 10.000 x 90.750Optional One Piece Edge 0.875 x 2.5
9F1831 2 SE|| 4 2.03 2.48 4.66 19.50 8.8540.625 x 8.000 x 14.000Router Bit 0.688 x 2
70 CURVED BOTTOM 8CSerial Number:
4T6626 1 DB|| 16 1.50 3.50 3.50 163.90 74.3480.875 x 13.000 x 55.500Drop Center 0.750 x 2.25
4T2882 1 DB|| 16 1.50 3.50 3.50 108.40 49.1780.750 x 10.000 x 55.500Level Cut Center 0.750 x 2.25
4T2883 2 DB|| 6 1.38 3.50 3.50 40.00 18.1460.750 x 10.000 x 20.250End 0.750 x 2.25
4T8807 1 DB|| 6 1.31 3.50 3.50 50.10 22.7260.875 x 12.000 x 20.125Wider Level Cut End RH 0.750 x 2.25
4T8808 1 DB|| 6 1.31 3.50 3.50 50.10 22.7260.875 x 12.000 x 20.125Wider Level Cut End LH 0.750 x 2.25
8F7232 2 SE|| 5 2.50 3.50 3.50 26.60 12.0750.750 x 8.000 x 16.000Router Bit 0.813 x 2.25
D22506 1 SE|| 28 1.63 3.50 3.500.750 x 6.500 x 96.750Straight Blade Support 0.813
70 3W 91DSerial Number:
4T6627 1 DB|| 18 3.13 6.00 6.00 156.80 71.1290.875 x 13.000 x 54.250Drop Center 0.875 x 2.53.13 6.00 6.00 ...2nd Row0.875 x 0
4T2941 1 DB|| 9 3.13 6.00 6.00 104.00 47.1790.750 x 10.000 x 54.250Level Cut Center 0.875 x 2.5
4T2942 2 DB|| 4 2.75 6.00 6.00 40.00 18.1440.750 x 10.000 x 23.500End 0.875 x 2.5
4T2947 1 DB|| 17 2.69 6.00 6.00 209.00 94.80170.750 x 10.000 x 101.375Optional One Piece Edge 0.875 x 2.5
8F7232 2 SE|| 5 2.50 3.50 3.50 26.60 12.0750.750 x 8.000 x 16.000Router Bit 0.813 x 2
80 CURVED BOTTOM 2DSerial Number:
4T6622 1 DB|| 17 1.75 3.50 3.50 174.70 79.24170.875 x 13.000 x 59.500Center 0.875 x 2.5
4T6624 2 DB|| 7 1.63 3.50 3.50 71.90 32.6170.875 x 13.000 x 24.500End 0.875 x 2.5
4T8805 1 DB|| 7 1.63 3.50 3.50 92.10 41.7871.000 x 15.500 x 24.250Wider Level Cut End RH 0.875 x 2.5
4T8806 1 DB|| 7 1.63 3.50 3.50 92.10 41.7871.000 x 15.500 x 24.250Wider Level Cut End LH 0.875 x 2.5
8F7232 2 SE|| 5 2.50 3.50 3.50 26.60 12.0750.750 x 8.000 x 16.000Router Bit 0.813 x 2.5
1J1299 1 IRR 5 2.25 2.50 3.50 64.00 29.031.250 x 10.000 x 22.750RH Router Bit Support 0.750
1J1300 1 IRR 5 2.25 2.50 3.50 64.00 29.031.250 x 10.000 x 22.750LH Router Bit Support 0.750
80 5WSerial Number:
4T6565 1 DB|| 18 3.13 6.00 6.00 192.30 87.2390.875 x 16.000 x 54.250Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
4T6617 1 DB|| 9 3.13 6.00 6.00 159.10 72.1790.875 x 13.000 x 54.250Level Cut Center 1.000 x 3
4T6612 2 DB|| 5 2.75 6.00 6.00 86.40 39.190.875 x 13.000 x 29.500End 1.000
4T2900 1 DB|| 18 3.13 6.00 6.00 250.90 113.8191.125 x 16.000 x 54.250HD Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6380 2 DB|| 5 2.75 6.00 6.00 113.60 51.5351.125 x 13.000 x 29.500HD End 1.000 x 3
8F7232 2 SE|| 5 2.50 3.50 3.50 26.60 12.0750.750 x 8.000 x 16.000Router Bit 0.813 x 2.5
6F3319 1 IRR 5 2.50 2.48 3.47 45.00 20.411.000 x 8.750 x 22.875RH Router Bit Support 0.750
6F3320 1 IRR 5 2.50 2.48 3.47 45.00 20.411.000 x 8.750 x 22.875LH Router Bit Support 0.750
90 9VSerial Number:
4T2887 1 DB|| 20 3.13 6.00 6.00 213.70 96.93100.875 x 16.000 x 60.250Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
4T6620 1 DB|| 10 3.13 6.00 6.00 176.60 80.10100.875 x 13.000 x 60.250Level Cut Center 1.000 x 3
4T6612 2 DB|| 5 2.75 6.00 6.00 86.40 39.1950.875 x 13.000 x 29.500End 1.000 x 3
4T2895 1 DB|| 20 3.13 6.00 6.00 278.60 126.37101.125 x 16.000 x 60.250HD Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
4T6620X11/8 1 DB|| 10 3.13 6.00 6.00 231.60 105.05101.125 x 13.000 x 60.250 1.000 x 3
4T6380 2 DB|| 5 2.75 6.00 6.00 113.60 51.5351.125 x 13.000 x 29.500HD End 1.000 x 3
1J3599FAB 2 SE// 5 2.50 3.50 3.50 47.50 21.5550.750 x 8.750 x 21.125RH/LH Router Bit 0.813 x 2.75
1J1299 1 IRR 5 2.25 2.50 3.50 64.00 29.031.250 x 10.000 x 22.750RH Router Bit Support 0.750
1J1300 1 IRR 5 2.25 2.50 3.50 64.00 29.031.250 x 10.000 x 22.750LH Router Bit Support 0.750
2T1969 1 IRR 30 2.63 6.00 6.00 372.40 168.921.000 x 13.500 x 119.250Drop Center Blade Support 1.06332.63 6.00 6.00 ...2nd Row1.063
D23500 1 WO 20 3.00 6.00 6.00 353.00 160.121.120 x 9.500 x 120.000Straight Blade Support 1.063
428 435 442 33F 35E 43D 44D 45D 83E 85F 88FSerial Number:
4T6567 1 DB|| 16 3.13 6.00 6.00 169.30 76.7980.875 x 16.000 x 48.250Drop Center 1.000 x 2.753.13 6.00 6.00 ...2nd Row1.000 x 0
4T6621 1 DB|| 8 3.13 6.00 6.00 141.40 64.1480.875 x 13.000 x 48.250Level Cut Center 1.000 x 2.75
4T6612 2 DB|| 5 2.75 6.00 6.00 86.40 39.1950.875 x 13.000 x 29.500End 1.000 x 2.75
1955131 2 DB|| 10 2.75 6.00 6.00 103.40 46.9050.875 x 16.000 x 29.500Wider Level Cut End 1.000 x 2.752.75 6.00 6.00 ...2nd Row1.000 x 0
4T2891 1 DB|| 16 3.13 6.00 6.00 224.00 101.6081.125 x 16.000 x 48.250HD Drop Center 1.000 x 2.753.13 6.00 6.00 ...2nd Row1.000 x 0
4T6380 2 DB|| 5 2.75 6.00 6.00 113.60 51.5351.125 x 13.000 x 29.500HD End 1.000 x 2.75
4T2894 2 DB|| 10 2.75 6.00 6.00 136.30 61.8251.125 x 16.000 x 29.500HD Wider Level Cut End 1.000 x 2.752.75 6.00 6.00 ...2nd Row1.000 x 0
1J3599FAB 2 SE// 5 2.50 3.50 3.50 47.50 21.5550.750 x 8.750 x 21.125RH/LH Router Bit 0.813 x 2.75
1J1299 1 IRR 5 2.25 2.50 3.50 64.00 29.031.250 x 10.000 x 22.750RH Router Bit Support 0.750
1J1300 1 IRR 5 2.25 2.50 3.50 64.00 29.031.250 x 10.000 x 22.750LH Router Bit Support 0.750
D15220 1 WO 18 267.00 121.111.000 x 9.000 x 110.000Straight Blade Support 1.063
456 463 470 491 60C 61C 62C 93D 94D 98CSerial Number:
4T2887 1 DB|| 20 3.13 6.00 6.00 213.70 96.93100.875 x 16.000 x 60.250Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
4T6620 1 DB|| 10 3.13 6.00 6.00 176.60 80.10100.875 x 13.000 x 60.250Level Cut Center 1.000 x 3
4T6612 2 DB|| 5 2.75 6.00 6.00 86.40 39.1950.875 x 13.000 x 29.500End 1.000 x 3
1955131 2 DB|| 10 2.75 6.00 6.00 103.40 46.9050.875 x 16.000 x 29.500Wider Level Cut End 1.000 x 32.75 6.00 6.00 ...2nd Row1.000 x 0
4T2895 1 DB|| 20 3.13 6.00 6.00 278.60 126.37101.125 x 16.000 x 60.250HD Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 3©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T6620X11/8 1 DB|| 10 3.13 6.00 6.00 231.60 105.05101.125 x 13.000 x 60.250 1.000 x 3
4T6380 2 DB|| 5 2.75 6.00 6.00 113.60 51.5351.125 x 13.000 x 29.500HD End 1.000 x 3
4T2894 2 DB|| 10 2.75 6.00 6.00 136.30 61.8251.125 x 16.000 x 29.500HD Wider Level Cut End 1.000 x 2.52.75 6.00 6.00 ...2nd Row1.000 x 0
1J3599FAB 2 SE// 5 2.50 3.50 3.50 47.50 21.5550.750 x 8.750 x 21.125RH/LH Router Bit 0.813 x 2.75
1J1299 1 IRR 5 2.25 2.50 3.50 64.00 29.031.250 x 10.000 x 22.750RH Router Bit Support 0.750
1J1300 1 IRR 5 2.25 2.50 3.50 64.00 29.031.250 x 10.000 x 22.750LH Router Bit Support 0.750
2T1969 1 IRR 30 2.63 6.00 6.00 372.40 168.921.000 x 13.500 x 119.250Drop Center Blade Support 1.06332.63 6.00 6.00 ...2nd Row1.063
D23500 1 WO 20 3.00 6.00 6.00 353.00 160.121.120 x 9.500 x 120.000Straight Blade Support 1.063
611 7WZSerial Number:
4T6566 1 DB|| 20 4.06 6.00 6.00 220.40 99.97100.875 x 16.000 x 62.125Drop Center 1.000 x 34.06 6.00 6.00 ...2nd Row1.000 x 0
1368752 2 DB|| 4 40.875 x 13.000 x End 1.000 x 3
4T3444 1 DB|| 20 4.06 6.00 6.00 287.60 130.45101.125 x 16.000 x 62.125HD Drop Center 1.000 x 34.06 6.00 6.00 ...2nd Row1.000 x 0
1379679 2 DB|| 4 41.125 x 13.000 x HD End 1.000 x 3
4J8665 1 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
613 72MSerial Number:
4T6611 1 DB|| 14 3.69 6.00 6.00 127.60 57.8870.875 x 13.000 x 43.375Level Cut Center 0.750 x 2.253.69 6.00 6.00 ...2nd Row0.750 x 0
4T6613 2 DB|| 8 2.06 6.00 6.00 64.30 29.1740.875 x 13.000 x 22.125End 0.750 x 2.252.06 6.00 6.00 ...2nd Row0.750 x 0
9F1831 2 SE|| 4 2.03 2.48 4.66 19.50 8.8540.625 x 8.000 x 14.000Router Bit 0.688 x 2.25
9J4413 1 4 4RH Level Cut Router Bit 0.625
9J4414 1 4 4LH Level Cut Router Bit 0.625
2T1919 1 IRR 22 2.13 6.00 6.00 224.00 101.600.750 x 13.750 x 88.000Drop Center Blade Support 0.8135.88 6.00 6.00 ...2nd Row0.813
D23501 1 WO 15 2.13 6.00 6.00 146.00 66.220.750 x 8.000 x 88.250Straight Blade Support 0.813
613 C 93X1-UPSerial Number:
4T6611 1 DB|| 14 3.69 6.00 6.00 127.60 57.8870.875 x 13.000 x 43.375Level Cut Center 0.750 x 2.253.69 6.00 6.00 ...2nd Row0.750 x 0
4T6613 2 DB|| 8 2.06 6.00 6.00 64.30 29.1740.875 x 13.000 x 22.125End 0.750 x 2.252.06 6.00 6.00 ...2nd Row0.750 x 0
4T4336 2 3 3.78 5.00 5.00 18.70 8.4830.625 x 8.000 x 17.563RH/LH Router Bit 0.688 x 2.25
9W4903 2 6 11.38 5.13 5.13 39.20 17.7831.000 x 7.000 x 22.500RH/LH Level Cut Router Bit 0.688 x 2.256.56 5.13 5.13 ...2nd Row0.688 x 0
2T1919 1 IRR 22 2.13 6.00 6.00 224.00 101.600.750 x 13.750 x 88.000Drop Center Blade Support 0.8135.88 6.00 6.00 ...2nd Row0.813
D23501 1 WO 15 2.13 6.00 6.00 146.00 66.220.750 x 8.000 x 88.250Straight Blade Support 0.813
615 47Z1340-UP 2XG-UPSerial Number:
9W5807 1 DB|| 18 5.75 6.00 6.00 211.50 95.9390.875 x 16.000 x 59.500Drop Center 1.000 x 3.255.75 6.00 6.00 ...2nd Row1.000 x 0
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 4©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W5810 2 DB|| 8 1.56 6.00 6.00 63.00 28.5840.875 x 13.000 x 21.125End 1.000 x 3.251.56 6.00 6.00 ...2nd Row1.000 x 0
9W5806 2 DB|| 8 1.56 6.00 6.00 74.50 33.7940.875 x 16.000 x 21.125Wider Level Cut End 1.000 x 3.251.56 6.00 6.00 ...2nd Row1.000 x 0
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
8J7210 1 IRR 5 17.10 7.765RH Scraper Floor Guide 1.000 x 2
8J7211 1 IRR 5 17.10 7.765LH Scraper Floor Guide 1.000 x 2
2T1955 2 IRR 9 1.25 28.30 12.841.000 x 5.500 x 25.500LH/RH Router Bit and Floor Guide Supp 1.000...2nd Row1.000
2T2479 1 WOSB 26 1.76 6.00 6.00 396.30 179.761.000 x 15.512 x 102.520Drop Center Blade Support 1.06327.26 6.00 6.00 ...2nd Row1.063
615 47Z1-1339Serial Number:
7T5104 1 DB|| 18 5.25 6.00 6.00 169.50 76.8890.875 x 13.000 x 58.500Center 0.875 x 35.25 6.00 6.00 ...2nd Row0.875 x 0
7T5105 2 DB|| 8 1.56 6.00 6.00 62.10 28.1740.875 x 13.000 x 21.563End 0.875 x 31.56 6.00 6.00 ...2nd Row0.875 x 0
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
8J7210 1 IRR 5 17.10 7.765RH Scraper Floor Guide 1.000 x 2
8J7211 1 IRR 5 17.10 7.765LH Scraper Floor Guide 1.000 x 2
2T1955 2 IRR 9 1.25 28.30 12.841.000 x 5.500 x 25.500LH/RH Router Bit and Floor Guide Supp 1.000...2nd Row1.000
619 C 68F 45F 48FSerial Number:
4T6567 1 DB|| 16 3.13 6.00 6.00 169.30 76.7980.875 x 16.000 x 48.250Drop Center 1.000 x 2.53.13 6.00 6.00 ...2nd Row1.000 x 0
4T6621 1 DB|| 8 3.13 6.00 6.00 141.40 64.1480.875 x 13.000 x 48.250Level Cut Center 1.000 x 2.5
4T6612 2 DB|| 5 2.75 6.00 6.00 86.40 39.1950.875 x 13.000 x 29.500End 1.000 x 2.5
1955131 2 DB|| 10 2.75 6.00 6.00 103.40 46.9050.875 x 16.000 x 29.500Wider Level Cut End 1.000 x 2.52.75 6.00 6.00 ...2nd Row1.000 x 0
4T2891 1 DB|| 16 3.13 6.00 6.00 224.00 101.6081.125 x 16.000 x 48.250HD Drop Center 1.000 x 2.53.13 6.00 6.00 ...2nd Row1.000 x 0
4T6380 2 DB|| 5 2.75 6.00 6.00 113.60 51.5351.125 x 13.000 x 29.500HD End 1.000 x 2.5
4T2894 2 DB|| 10 2.75 6.00 6.00 136.30 61.8251.125 x 16.000 x 29.500HD Wider Level Cut End 1.000 x 2.52.75 6.00 6.00 ...2nd Row1.000 x 0
4J8665 2 SE// 5 2.50 3.50 56.90 25.810.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
2J9193 1 IRR 5 2.13 2.50 3.50 89.00 40.371.250 x 12.500 x 24.000RH Router Bit Support 1.000
2J9194 1 IRR 5 2.13 2.50 3.50 89.00 40.371.250 x 12.500 x 24.000LH Router Bit Support 1.000
D15220 1 WO 18 267.00 121.111.000 x 9.000 x 110.000Straight Blade Support 1.063
621 627 B E F G 69M 50K 4YK 37V 38V 6FB 6HB AYK CEZ 37G 36V 6BB 5JK ANG CEPSerial Number:
4T6568 1 DB|| 18 4.13 6.00 6.00 197.60 89.6390.875 x 16.000 x 56.250Drop Center 1.000 x 34.13 6.00 6.00 ...2nd Row1.000 x 0
4T6612 2 DB|| 5 2.75 6.00 6.00 86.40 39.1950.875 x 13.000 x 29.500End 1.000 x 3
1955131 2 DB|| 10 2.75 6.00 6.00 103.40 46.9050.875 x 16.000 x 29.500Wider Level Cut End 1.000 x 32.75 6.00 6.00 ...2nd Row1.000 x 0
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 5©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T2896 1 DB|| 18 4.13 6.00 6.00 262.00 118.841.125 x 16.000 x 56.250HD Drop Center 1.0004.13 6.00 6.00 ...2nd Row1.000
1406779 1 DB|| 18 4.13 6.00 6.00 262.00 118.8491.125 x 16.000 x 56.250C/IMP Drop Center 1.000 x 34.13 6.00 6.00 ...2nd Row1.000 x 0
1957279 1 DB|| 91.125 x 16.000 x 56.250Serrated Drop Center x 3
1406767 1 DB|| 91.125 x 16.000 x 56.250C/IMP Serrated Drop Center x 3
4T2894 2 DB|| 10 2.75 6.00 6.00 136.30 61.8251.125 x 16.000 x 29.500HD Wider Level Cut End 1.000 x 32.75 6.00 6.00 ...2nd Row1.000 x 0
1441323 2 DB|| 51.125 x 16.000 x 29.500C/IMP HD Wider Level Cut End x 3
4T6380 2 DB|| 5 2.75 6.00 6.00 113.60 51.5351.125 x 13.000 x 29.500HD End 1.000 x 3
1406778 2 DB|| 5 2.75 6.00 6.00 113.00 51.2651.125 x 13.000 x 29.500C/IMP HD End 1.000 x 3
2571857 1 DB|| 18 4.13 6.00 6.00 321.40 145.781.375 x 16.000 x 56.250Drop Center 1.0004.13 6.00 6.00 ...2nd Row1.000
2571870 2 DB|| 10 2.75 6.00 6.001.375 x 16.000 x 29.500Wider Level Cut End 1.0002.75 6.00 6.00 ...2nd Row1.000
1324566 1 DB|| 18 4.13 6.00 6.00 381.00 172.8291.625 x 16.000 x 56.250Extra HD Center 1.000 x 34.13 6.00 6.00 ...2nd Row1.000 x 0
1324567 2 DB|| 5 2.75 6.00 6.00 162.00 73.4851.625 x 13.000 x 29.500Extra HD End 1.000 x 3
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
1433065 2 SE// 5 54.00 24.4950.750 x 8.500 x 21.000C/IMP RH/LH Router Bit 1.000 x 3
5J2171 1 IRR 5 2.02 2.50 3.50 130.80 59.331.500 x 15.500 x 24.750RH Router Bit Support 1.000
5J2172 1 IRR 5 2.02 2.50 3.50 130.80 59.331.500 x 15.500 x 24.750LH Router Bit Support 1.000
4T7667 1 IRR 5 2.00 2.50 3.50 117.20 53.161.250 x 15.000 x 28.000RH Router Bit Support 1.000
4T7668 1 IRR 5 2.00 2.50 3.50 117.20 53.161.250 x 15.000 x 28.000LH Router Bit Support 1.000
5J0950DC 1 IRR 28 3.50 6.00 6.00 426.70 193.551.125 x 13.500 x 117.000Drop Center Blade Support 1.00034.50 6.00 6.00 ...2nd Row1.000
5J0950 1 IRR 19 3.50 376.40 170.731.125 x 10.250 x 117.000Straight Blade Support 1.063
1U1566 1 IRR 9.50 4.310.750 x 4.213 x 22.677Support Gusset
621 627 H DBK EAZ HKK NYY DBW LCTSerial Number:
4T2887 1 DB|| 20 3.13 6.00 6.00 213.70 96.93100.875 x 16.000 x 60.250Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
4T6620 1 DB|| 10 3.13 6.00 6.00 176.60 80.10100.875 x 13.000 x 60.250Level Cut Center 1.000 x 3
4T6612 2 DB|| 5 2.75 6.00 6.00 86.40 39.1950.875 x 13.000 x 29.500End 1.000 x 3
1955131 2 DB|| 10 2.75 6.00 6.00 103.40 46.9050.875 x 16.000 x 29.500Wider Level Cut End 1.000 x 32.75 6.00 6.00 ...2nd Row1.000 x 0
4T2895 1 DB|| 20 3.13 6.00 6.00 278.60 126.37101.125 x 16.000 x 60.250HD Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
2013439 1 DB|| 101.125 x 16.000 x 60.250Serrated Drop Center x 3
1406847 1 DB|| 101.125 x 16.000 x 60.250C/IMP Drop Center x 3
1406780 1 DB|| 101.125 x 16.000 x 60.250C/IMP Serrated Drop Center x 3
1441340 1 DB|| 101.125 x 13.000 x 60.250C/IMP Level Cut Center x 3
4T6380 2 DB|| 5 2.75 6.00 6.00 113.60 51.5351.125 x 13.000 x 29.500HD End 1.000 x 3
4T2894 2 DB|| 10 2.75 6.00 6.00 136.30 61.8251.125 x 16.000 x 29.500Wider Level Cut End 1.000 x 32.75 6.00 6.00 ...2nd Row1.000 x 0
1406778 2 DB|| 5 2.75 6.00 6.00 113.00 51.2651.125 x 13.000 x 29.500C/IMP HD End 1.000 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 6©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
1441323 2 DB|| 51.125 x 16.000 x 29.500C/IMP HD Wider Level Cut End x 3
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
1433065 2 SE// 5 54.00 24.4950.750 x 8.500 x 21.000C/IMP RH/LH Router Bit 1.000 x 3
2T1955 2 IRR 9 1.25 28.30 12.841.000 x 5.500 x 25.500LH/RH Router Bit and Floor Guide Supp 1.000...2nd Row1.000
2J9193 1 IRR 5 2.13 2.50 3.50 89.00 40.371.250 x 12.500 x 24.000RH Router Bit Support 1.000
2J9194 1 IRR 5 2.13 2.50 3.50 89.00 40.371.250 x 12.500 x 24.000LH Router Bit Support 1.000
2T1969 1 IRR 30 2.63 6.00 6.00 372.40 168.921.000 x 13.500 x 119.250Drop Center Blade Support 1.06332.63 6.00 6.00 ...2nd Row1.063
D23500 1 WO 20 3.00 6.00 6.00 353.00 160.121.120 x 9.500 x 120.000Straight Blade Support 1.063
623 J619 J621 26U 5SG 61E 6DB AWB CEW 43F 43HSerial Number:
4T2887 1 DB|| 20 3.13 6.00 6.00 213.70 96.93100.875 x 16.000 x 60.250Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
4T6620 1 DB|| 10 3.13 6.00 6.00 176.60 80.10100.875 x 13.000 x 60.250Level Cut Center 1.000 x 3
4T6612 2 DB|| 5 2.75 6.00 6.00 86.40 39.1950.875 x 13.000 x 29.500End 1.000 x 3
1955131 2 DB|| 10 2.75 6.00 6.00 103.40 46.9050.875 x 16.000 x 29.500Wider Level Cut End 1.000 x 32.75 6.00 6.00 ...2nd Row1.000 x 0
4T2895 1 DB|| 20 3.13 6.00 6.00 278.60 126.37101.125 x 16.000 x 60.250HD Drop Center 1.000 x 33.13 6.00 6.00 ...2nd Row1.000 x 0
2013439 1 DB|| 101.125 x 16.000 x 60.250Serrated Drop Center x 3
1406847 1 DB|| 101.125 x 16.000 x 60.250C/IMP Drop Center x 3
1406780 1 DB|| 101.125 x 16.000 x 60.250C/IMP Serrated Drop Center x 3
1441340 1 DB|| 101.125 x 13.000 x 60.250C/IMP Level Cut Center x 3
4T6380 2 DB|| 5 2.75 6.00 6.00 113.60 51.5351.125 x 13.000 x 29.500HD End 1.000 x 3
4T2894 2 DB|| 10 2.75 6.00 6.00 136.30 61.8251.125 x 16.000 x 29.500Wider Level Cut End 1.000 x 32.75 6.00 6.00 ...2nd Row1.000 x 0
1406778 2 DB|| 5 2.75 6.00 6.00 113.00 51.2651.125 x 13.000 x 29.500C/IMP HD End 1.000 x 3
1441323 2 DB|| 51.125 x 16.000 x 29.500C/IMP HD Wider Level Cut End x 3
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
1433065 2 SE// 5 54.00 24.4950.750 x 8.500 x 21.000C/IMP RH/LH Router Bit 1.000 x 3
8J7210 1 IRR 5 17.10 7.765RH Scraper Floor Guide 1.000 x 2
8J7211 1 IRR 5 17.10 7.765LH Scraper Floor Guide 1.000 x 2
2T1955 2 IRR 9 1.25 28.30 12.841.000 x 5.500 x 25.500LH/RH Router Bit and Floor Guide Supp 1.000...2nd Row1.000
2J9193 1 IRR 5 2.13 2.50 3.50 89.00 40.371.250 x 12.500 x 24.000RH Router Bit Support 1.000
2J9194 1 IRR 5 2.13 2.50 3.50 89.00 40.371.250 x 12.500 x 24.000LH Router Bit Support 1.000
2T1969 1 IRR 30 2.63 6.00 6.00 372.40 168.921.000 x 13.500 x 119.250Drop Center Blade Support 1.06332.63 6.00 6.00 ...2nd Row1.063
D23500 1 WO 20 3.00 6.00 6.00 353.00 160.121.120 x 9.500 x 120.000Straight Blade Support 1.063
630 631 637 B C 64M 11G 10G 28F 32FSerial Number:
4T6565 1 DB|| 18 3.13 6.00 6.00 192.30 87.2390.875 x 16.000 x 54.250Drop Center 1.000 x 3.253.13 6.00 6.00 ...2nd Row1.000 x 0
4T6614 2 DB|| 6 2.75 6.00 6.00 105.00 47.6360.875 x 13.000 x 35.500End 1.000 x 3.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 7©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T2900 1 DB|| 18 3.13 6.00 6.00 250.90 113.8191.125 x 16.000 x 54.250HD Drop Center 1.000 x 3.253.13 6.00 6.00 ...2nd Row1.000 x 0
4T6378 2 DB|| 6 2.75 6.00 6.00 136.50 61.9261.125 x 13.000 x 35.500HD End 1.000 x 3.25
7J3026 1 DB|| 18 3.13 6.00 6.00 309.40 140.3491.375 x 16.000 x 54.250Drop Center 1.000 x 3.253.13 6.00 6.00 ...2nd Row1.000 x 0
9W6092 2 DB|| 6 2.75 6.00 6.00 168.50 76.4361.375 x 13.000 x 35.500End 1.000 x 3.25
7J0225 2 DB|| 14 2.75 6.00 6.00 202.10 91.6761.375 x 16.000 x 35.500Wider Level Cut End 1.000 x 3.252.75 6.00 6.00 ...2nd Row1.000 x 0
7J2957 1 DB|| 18 3.13 6.00 6.00 369.80 167.7491.625 x 16.000 x 54.250Drop Center 1.000 x 3.253.13 6.00 6.00 ...2nd Row1.000 x 0
7J2959 2 DB|| 8 2.75 6.00 6.00 199.90 90.6761.625 x 13.000 x 35.500End 1.000 x 3.25
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
7J3023 2 SE// 5 2.50 3.50 86.60 39.2850.875 x 9.625 x 22.750RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
5J3101 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688RH Router Bit Support 1.000
5J3102 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688LH Router Bit Support 1.000
4J6773 1 IRR 5 140.00 63.501.250 x 17.500 x 30.000RH Router Bit Support 1.000
4J6774 1 IRR 5 140.00 63.501.250 x 17.500 x 30.000LH Router Bit Support 1.000
7J4227 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000RH Router Bit Support 1.000
7J4228 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000LH Router Bit Support 1.000
4J7249 1 IRR 30 3.00 6.00 6.00 424.40 192.501.125 x 13.500 x 126.000Drop Center Blade Support 1.06339.00 6.00 6.00 ...2nd Row1.063
631 637 D E G 20W-23W 7CB 1LB 1HB AWE AYN 28W 29W 1BB AXZSerial Number:
4T6566 1 DB|| 20 4.06 6.00 6.00 220.40 99.97100.875 x 16.000 x 62.125Drop Center 1.000 x 34.06 6.00 6.00 ...2nd Row1.000 x 0
4T6614 2 DB|| 6 2.75 6.00 6.00 105.00 47.6360.875 x 13.000 x 35.500End 1.000 x 3
4T3444 1 DB|| 20 4.06 6.00 6.00 287.60 130.45101.125 x 16.000 x 62.125HD Drop Center 1.000 x 34.06 6.00 6.00 ...2nd Row1.000 x 0
1386443 1 DB|| 20 4.06 6.00 6.00 288.00 130.63101.125 x 16.000 x 62.120C/IMP Drop Center 1.000 x 34.06 6.00 6.00 ...2nd Row1.000 x 0
4T6378 2 DB|| 6 2.75 6.00 6.00 136.50 61.9261.125 x 13.000 x 35.500HD End 1.000 x 3
1386444 2 DB|| 6 2.75 6.00 6.00 139.00 63.0561.125 x 13.000 x 35.500C/IMP HD End 1.000 x 3
9J4369 1 DB|| 20 4.06 6.00 6.00 359.00 162.84101.375 x 16.000 x 62.125Extra HD Center 1.000 x 34.06 6.00 6.00 ...2nd Row1.000 x 0
1386445 1 DB|| 20 4.06 6.00 6.00 359.00 162.84101.375 x 16.000 x 62.120C/IMP Drop Center 1.000 x 34.06 6.00 6.00 ...2nd Row1.000 x 0
1441557 1 DB|| 101.375 x 16.000 x 62.125C/IMP Serrated Drop Center x 3
9W6092 2 DB|| 6 2.75 6.00 6.00 168.50 76.4361.375 x 13.000 x 35.500Extra HD End 1.000 x 3
1386446 2 DB|| 6 2.75 6.00 6.00 168.00 76.2061.375 x 13.000 x 35.500C/IMP HD End 1.000 x 3
7J0225 2 DB|| 14 2.75 6.00 6.00 202.10 91.6761.375 x 16.000 x 35.500Wider Level Cut End 1.000 x 32.75 6.00 6.00 ...2nd Row1.000 x 0
9J5899 1 DB|| 20 4.06 6.00 6.00 422.30 191.55101.625 x 16.000 x 62.125Extra HD Center 1.000 x 34.06 6.00 6.00 ...2nd Row1.000 x 0
1955114 1 DB|| 101.625 x 16.000 x 62.125C/IMP Drop Center x 3
7J2959 2 DB|| 8 2.75 6.00 6.00 199.90 90.6761.625 x 13.000 x 35.500Extra HD End 1.000 x 3
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 8©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7J3023 2 SE// 5 2.50 3.50 86.60 39.2850.875 x 9.625 x 22.750HD RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
1433065 2 SE// 5 54.00 24.4950.750 x 8.500 x 21.000C/IMP RH/LH Router Bit 1.000 x 3
1433079 2 SE// 5 5C/IMP RH/LH Router Bit 1.000 x 3
5J3101 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688RH Router Bit Support 1.000
5J3102 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688LH Router Bit Support 1.000
7J4227 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000RH Router Bit Support 1.000
7J4228 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000LH Router Bit Support 1.000
9J0021DC 1 IRR 30 3.50 6.00 6.00 458.00 207.751.125 x 13.500 x 135.000Drop Center Blade Support 1.0632.83 6.00 6.00 ...2nd Row1.063
9J0021 1 IRR 22 3.50 6.00 6.00 419.00 190.061.125 x 10.250 x 135.000Straight Blade Support 1.063
632 641 71G 79F 42M 43M 70G 80FSerial Number:
4T2887 1 DB|| 20 3.13 6.00 6.00 213.70 96.93100.875 x 16.000 x 60.250Drop Center 1.000 x 3.253.13 6.00 6.00 ...2nd Row1.000 x 0
4T6614 2 DB|| 6 2.75 6.00 6.00 105.00 47.6360.875 x 13.000 x 35.500End 1.000 x 3.25
4T2895 1 DB|| 20 3.13 6.00 6.00 278.60 126.37101.125 x 16.000 x 60.250Drop Center 1.000 x 3.253.13 6.00 6.00 ...2nd Row1.000 x 0
4T6378 2 DB|| 6 2.75 6.00 6.00 136.50 61.9261.125 x 13.000 x 35.500Center and Outer Ends 1.000 x 3.25
4J8226 1 DB|| 20 3.13 6.00 6.00 348.23 157.95101.375 x 16.000 x 60.250Drop Center 1.000 x 3.253.13 6.00 6.00 ...2nd Row1.000 x 0
9W6092 2 DB|| 6 2.75 6.00 6.00 168.50 76.4361.375 x 13.000 x 35.500End 1.000 x 3.25
7J0225 2 DB|| 14 2.75 6.00 6.00 202.10 91.6761.375 x 16.000 x 35.500Wider Level Cut End 1.000 x 3.252.75 6.00 6.00 ...2nd Row1.000 x 0
7J2958 1 DB|| 20 3.13 6.00 6.00 410.70 186.29101.625 x 16.000 x 60.250Drop Center 1.000 x 3.253.13 6.00 6.00 ...2nd Row1.000 x 0
7J2959 2 DB|| 8 2.75 6.00 6.00 199.90 90.6761.625 x 13.000 x 35.500Center and Outer Ends 1.000 x 3.25
4J8665 2 SE// 5 2.50 3.50 56.90 25.810.750 x 8.500 x 21.000RH/LH Router Bit 1.000
7J3023 2 SE// 5 2.50 3.50 86.60 39.280.875 x 9.625 x 22.750RH/LH Router Bit 1.000
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
5J3101 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688RH Router Bit Support 1.000
5J3102 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688LH Router Bit Support 1.000
7J4227 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000RH Router Bit Support 1.000
7J4228 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000LH Router Bit Support 1.000
D7193 1 WO 22 3.00 6.00 6.00 378.00 171.461.125 x 9.250 x 132.000Straight Blade Support 1.063
633 86HSerial Number:
4T2892 1 DB|| 24 4.13 6.00 6.00 315.70 143.20111.125 x 16.000 x 68.250Drop Center 1.000 x 3.54.13 6.00 6.00 ...2nd Row1.000 x 0
4T3429 2 DB|| 10 2.25 6.00 6.00 131.10 59.4751.125 x 16.000 x 28.500Wider Level Cut End 1.000 x 3.52.25 6.00 6.00 ...2nd Row1.000 x 0
1406762 1 DB||C/IMP Drop Center
1406763 2 DB||C/IMP HD Wider Level Cut End
4J8225 1 DB|| 24 4.13 6.00 6.00 389.60 176.72111.375 x 16.000 x 68.250Drop Center 1.000 x 3.54.13 6.00 6.00 ...2nd Row1.000 x 0
7J3192 2 DB|| 10 2.25 6.00 6.00 162.40 73.6651.375 x 16.000 x 28.500Wider Level Cut End 1.000 x 3.52.25 6.00 6.00 ...2nd Row1.000 x 0
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 9©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
7J3023 2 SE// 5 2.50 3.50 86.60 39.2850.875 x 9.625 x 22.750RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
633-639BS 1 SE|| 42 2.38 6.00 6.00 540.00 244.941.250 x 12.500 x 126.000Straight Blade Support 1.0632.38 69.00 6.00 ...2nd Row1.063
633 639 D E 19W 1EB 88WSerial Number:
4T3428 1 DB|| 22 2.81 6.00 6.00 302.40 137.17111.125 x 16.000 x 65.625Drop Center 1.000 x 3.252.81 6.00 6.00 ...2nd Row1.000 x 0
1406764 1 DB|| 111.125 x 16.000 x 65.625C/IMP Drop Center x 3.25
4T2899 2 DB|| 12 1.88 6.00 6.00 155.60 70.5861.125 x 16.000 x 33.750Wider Level Cut End 1.000 x 3.251.88 6.00 6.00 ...2nd Row1.000 x 0
1406765 1 DB||C/IMP HD Wider Level Cut End
9J1111 1 DB|| 22 2.81 6.00 6.00 374.80 170.01111.375 x 16.000 x 65.625Drop Center 1.000 x 3.252.81 6.00 6.00 ...2nd Row1.000 x 0
1368776 1 DB|| 111.375 x 16.000 x 65.625C/IMP Serrated Drop Center x 3.25
9J1109 2 DB|| 12 1.88 6.00 6.00 192.30 87.2361.375 x 16.000 x 33.750Wider Level Cut End 1.000 x 3.251.88 6.00 6.00 ...2nd Row1.000 x 0
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
7J3023 2 SE// 5 2.50 3.50 86.60 39.2850.875 x 9.625 x 22.750RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
1433065 2 SE// 5 54.00 24.4950.750 x 8.500 x 21.000C/IMP RH/LH Router Bit 1.000 x 3
1433079 2 SE// 5 5HD C/IMP RH/LH Router Bit 1.000 x 3
5J3101 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688RH Router Bit Support 1.000
5J3102 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688LH Router Bit Support 1.000
7J4227 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000RH Router Bit Support 1.000
7J4228 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000LH Router Bit Support 1.000
D17958 1 SB|| 46 2.00 6.00 6.00 441.00 200.031.000 x 12.000 x 134.000Straight Blade Support 1.0632.00 6.00 6.00 ...2nd Row1.063
650 651 657 660 666 B 20G1-93 23G1-126 19G1-221 18G1-77 22G1-164Serial Number:
4T2892 1 DB|| 24 4.13 6.00 6.00 315.70 143.20111.125 x 16.000 x 68.250Drop Center 1.000 x 3.254.13 6.00 6.00 ...2nd Row1.000 x 0
4T6378 2 DB|| 6 2.75 6.00 6.00 136.50 61.9261.125 x 13.000 x 35.500End 1.000 x 3.25
4J8225 1 DB|| 24 4.13 6.00 6.00 389.60 176.72111.375 x 16.000 x 68.250Drop Center 1.000 x 3.254.13 6.00 6.00 ...2nd Row1.000 x 0
9W6092 2 DB|| 6 2.75 6.00 6.00 168.50 76.4361.375 x 13.000 x 35.500End 1.000 x 3.25
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
7J3023 2 SE// 5 2.50 3.50 86.60 39.2850.875 x 9.625 x 22.750RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
5J3101 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688RH Router Bit Support 1.000
5J3102 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688LH Router Bit Support 1.000
7J4227 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000RH Router Bit Support 1.000
7J4228 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000LH Router Bit Support 1.000
7J3583 1 IRR 5 1.03 3.92 189.50 85.961.625 x 17.380 x 31.380LH Router Bit Support 1.000
7J3584 1 IRR 5 2.01 2.50 3.50 189.50 85.961.625 x 17.380 x 31.380RH Router Bit Support 1.000
650 651 657 660 666 20G94-UP 23G127-UP 45M1-UP 19G222-UP 47M1-UP 18G78-UP 22G165-UPSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 10©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7J1551 1 DB|| 35 4.13 6.00 6.00 465.80 211.28111.375 x 19.000 x 68.250Extra Wide Center 1.000 x 3.2511 4.13 6.00 6.00 ...2nd Row1.000 x 3.25
7J0226 1 DB|| 24 4.13 6.00 6.00 389.40 176.63111.375 x 16.000 x 68.250Drop Center 1.000 x 3.2511 4.13 6.00 6.00 ...2nd Row1.000 x 3.25
9W6092 2 DB|| 6 2.75 6.00 6.00 168.50 76.4361.375 x 13.000 x 35.500End 1.000 x 3.25
7J0225 2 DB|| 14 2.75 6.00 6.00 202.10 91.6761.375 x 16.000 x 35.500Wider Level Cut End 1.000 x 3.256 2.75 6.00 6.00 ...2nd Row1.000 x 3.25
7J2977 1 DB|| 35 4.13 6.00 6.00 591.80 268.44111.750 x 19.000 x 68.250Extra Wide Center 1.000 x 3.2511 4.13 6.00 6.00 ...2nd Row1.000 x 3.25
7J2981 1 DB|| 24 4.13 6.00 6.00 463.60 210.29111.625 x 16.000 x 68.250Drop Center 1.000 x 3.2511 4.13 6.00 6.00 ...2nd Row1.000 x 3.25
7J2959 2 DB|| 8 2.75 6.00 6.00 199.90 90.6761.625 x 13.000 x 35.500End 1.000 x 3.25
7J2978 2 DB|| 14 2.75 6.00 6.00 240.50 109.0961.625 x 16.000 x 35.500Wider Level Cut End 1.000 x 3.256 2.75 6.00 6.00 ...2nd Row1.000 x 3.25
4J8665 2 SE// 5 2.50 3.50 56.90 25.8150.750 x 8.500 x 21.000RH/LH Router Bit 1.000 x 3
7J3023 2 SE// 5 2.50 3.50 86.60 39.2850.875 x 9.625 x 22.750RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
5J3101 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688RH Router Bit Support 1.000
5J3102 1 IRR 5 2.06 2.50 3.50 97.00 44.001.000 x 15.438 x 27.688LH Router Bit Support 1.000
7J4227 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000RH Router Bit Support 1.000
7J4228 1 IRR 5 2.06 2.50 3.50 149.40 67.771.500 x 15.500 x 28.000LH Router Bit Support 1.000
7J3583 1 IRR 5 1.03 3.92 189.50 85.961.625 x 17.380 x 31.380LH Router Bit Support 1.000
7J3584 1 IRR 5 2.01 2.50 3.50 189.50 85.961.625 x 17.380 x 31.380RH Router Bit Support 1.000
5J3305DC 1 IRR 46 3.00 6.00 6.00 654.30 296.791.250 x 15.000 x 140.000Drop Center Blade Support 1.0633.00 6.00 6.00 ...2nd Row1.063
D9913 1 WO 46 3.50 6.00 6.00 757.00 343.371.500 x 13.000 x 141.250Straight Blade Support 1.0633.50 6.00 6.00 ...2nd Row1.063
651 657 E F 86Z1-240 6MB1-90 88Z1-145Serial Number:
9W4505 1 DB|| 28 4.06 3.00 3.00 375.90 170.51131.375 x 16.000 x 68.125Drop Center 1.250 x 3.754.06 3.00 3.00 ...2nd Row1.250 x 0
9W4399 2 DB|| 10 4.00 3.00 3.00 175.90 79.7981.375 x 13.000 x 38.000End 1.250 x 3.75
9W4394 1 DB|| 28 4.06 3.00 3.00 446.00 202.30131.625 x 16.000 x 68.125Drop Center 1.250 x 3.754.06 3.00 3.00 ...2nd Row1.250 x 0
9W4509 2 DB|| 10 4.00 3.00 3.00 208.50 94.5781.625 x 13.000 x 38.000End 1.250 x 3.75
2367178 1 DB|| 33 4.06 6.00 6.001.750 x 19.000 x 68.125C/IMP Drop Center 1.2504.06 6.00 6.00 ...2nd Row1.250
2367179 2 DB|| 12 4.00 6.00 6.001.750 x 16.000 x 38.000C/IMP HD End 1.2504.00 6.00 6.00 ...2nd Row1.250
4T0668FAB 2 DB|| 5 5.62 3.00 3.00 107.60 48.8151.375 x 10.060 x 22.960RH/LH Router Bit 1.250 x 4.125
D13878RH 1 IRR 5 2.63 3.00 3.00 149.80 67.951.500 x 15.500 x 28.000RH Router Bit Support 1.250
D13878LH 1 IRR 5 2.63 3.00 3.00 149.80 67.951.500 x 15.500 x 28.000LH Router Bit Support 1.250
D1972 1 WO 29 5.00 3.00 3.00 641.00 290.751.625 x 10.000 x 146.500Straight Blade Support 1.375
651 657 E F 7KR 6PR 5KR 86Z241-UP 6MB91-UP 88Z146-UPSerial Number:
9W4901 1 DB|| 38 2.88 6.00 6.00 488.80 221.72121.375 x 19.000 x 71.750Drop Center 1.000 x 3.2512 2.88 6.00 6.00 ...2nd Row1.000 x 3.25
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 11©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Scraper
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W4902 2 DB|| 14 2.88 6.00 6.00 203.60 92.3561.375 x 16.000 x 35.750End 1.000 x 3.256 2.88 6.00 6.00 ...2nd Row1.000 x 3.25
9W9701 1 DB|| 38 2.88 6.00 6.00 621.20 281.77121.750 x 19.000 x 71.750Drop Center 1.000 x 3.2512 2.88 6.00 6.00 ...2nd Row1.000 x 3.25
9W9702 2 DB|| 14 2.88 6.00 6.00 261.80 118.7561.750 x 16.000 x 35.750End 1.000 x 3.256 2.88 6.00 6.00 ...2nd Row1.000 x 3.25
1590374 1 DB|| 12C/IMP Drop Center x 3.25
1590375 2 DB|| 6C/IMP HD End x 3.25
9W9701-20 1 DB|| 36 2.88 6.00 6.00122.500 x 19.000 x 71.750Drop Center 1.000 x 3.2512 2.88 6.00 6.00 ...2nd Row1.000 x 3.25
1359327 2 DB|| 12 2.88 6.00 6.00 373.00 169.1962.375 x 16.000 x 35.750End 1.000 x 3.256 2.88 6.00 6.00 ...2nd Row1.000 x 3.25
7J3023 2 SE// 5 2.50 3.50 86.60 39.2850.875 x 9.625 x 22.750RH/LH Router Bit 1.000 x 3
2209150 2 SE// 5 3.64 2.50 3.50 112.40 50.9851.000 x 11.000 x 26.000RH/LH Level Cut Router Bit 1.000 x 3
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 12©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader End Bits and Overlays
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
112 ALLSerial Number:
7D2052 2 RH/LH 5 1.31 3.94 3.94 14.00 6.3550.500 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W2945 2 RH/LH 5 1.31 3.94 3.94 18.00 8.160.625 x 6.000 x 18.374Heavy Duty End bit LH/RH 0.625 x 2.25
6D1904 2 RH/LH 8 4.31 9.63 22.50 10.2150.500 x 9.250 x 18.250Overlay LH/RH for 6" blades 0.625 x 33.50 3.75 3.75 ...2nd Row0.625 x 0
6D1948 2 RH/LH 8 6.31 9.63 27.70 12.5650.500 x 9.250 x 22.250Overlay LH/RH for 8" blades 0.625 x 35.50 3.75 3.75 ...2nd Row0.625 x 0
4D5757 1 RH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay RH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
4D5758 1 LH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay LH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
212 ALLSerial Number:
9J4411 2 RH/LH 4 1.50 3.81 3.81 11.00 4.9940.500 x 6.000 x 14.438End bit LH/RH 0.625 x 2.25
12 ALLSerial Number:
7D2052 2 RH/LH 5 1.31 3.94 3.94 14.00 6.3550.500 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W2945 2 RH/LH 5 1.31 3.94 3.94 18.00 8.160.625 x 6.000 x 18.374Heavy Duty End bit LH/RH 0.625 x 2.25
6D1904 2 RH/LH 8 4.31 9.63 22.50 10.2150.500 x 9.250 x 18.250Overlay LH/RH for 6" blades 0.625 x 33.50 3.75 3.75 ...2nd Row0.625 x 0
6D1948 2 RH/LH 8 6.31 9.63 27.70 12.5650.500 x 9.250 x 22.250Overlay LH/RH for 8" blades 0.625 x 35.50 3.75 3.75 ...2nd Row0.625 x 0
4D5757 1 RH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay RH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
4D5758 1 LH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay LH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
12 G UP TO 61M1-11715Serial Number:
7D2052 2 RH/LH 5 1.31 3.94 3.94 14.00 6.3550.500 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W2945 2 RH/LH 5 1.31 3.94 3.94 18.00 8.160.625 x 6.000 x 18.374Heavy Duty End bit LH/RH 0.625 x 2.25
6D1904 2 RH/LH 8 4.31 9.63 22.50 10.2150.500 x 9.250 x 18.250Overlay LH/RH for 6" blades 0.625 x 33.50 3.75 3.75 ...2nd Row0.625 x 0
6D1948 2 RH/LH 8 6.31 9.63 27.70 12.5650.500 x 9.250 x 22.250Overlay LH/RH for 8" blades 0.625 x 35.50 3.75 3.75 ...2nd Row0.625 x 0
4D5757 1 RH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay RH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
4D5758 1 LH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay LH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
12 G H 12G(31M11716-UP) 12H(ALL)Serial Number:
8E5531 1 RH/LH 5 1.63 3.78 3.78 17.50 7.9450.625 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W1767 2 RH/LH 8 4.38 9.88 23.00 10.4350.500 x 9.250 x 18.625Overlay LH/RH for 6" blades 0.625 x 33.78 3.69 3.69 ...2nd Row0.625 x 0
9W1768 2 RH/LH 8 5.97 9.88 27.10 12.2950.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.625 x 35.38 3.69 3.69 ...2nd Row0.625 x 0
12 K M M2 ALLSerial Number:
8E5529 2 RH/LH 5 1.56 3.78 3.78 16.90 7.6750.625 x 6.000 x 18.250End bit LH/RH 0.750 x 2.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader End Bits and Overlays
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
2322142 2 RH/LH 8 4.37 9.87 6.00 22.70 10.300.500 x 18.626 x 9.252Overlay LH/RH for 6" blades 0.7503.78 3.69 3.69 ...2nd Row0.750
6Y2805 2 RH/LH 8 5.97 9.88 26.90 12.2050.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.750 x 3.255.38 3.69 3.69 ...2nd Row0.750 x 0
120 G UP TO 87V1-6134Serial Number:
7D2052 2 RH/LH 5 1.31 3.94 3.94 14.00 6.3550.500 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W2945 2 RH/LH 5 1.31 3.94 3.94 18.00 8.160.625 x 6.000 x 18.374Heavy Duty End bit LH/RH 0.625 x 2.25
6D1904 2 RH/LH 8 4.31 9.63 22.50 10.2150.500 x 9.250 x 18.250Overlay LH/RH for 6" blades 0.625 x 33.50 3.75 3.75 ...2nd Row0.625 x 0
6D1948 2 RH/LH 8 6.31 9.63 27.70 12.5650.500 x 9.250 x 22.250Overlay LH/RH for 8" blades 0.625 x 35.50 3.75 3.75 ...2nd Row0.625 x 0
4D5757 1 RH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay RH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
4D5758 1 LH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay LH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
120 G H 120G(87V08135-UP) 120H(ALL)Serial Number:
8E5531 1 RH/LH 5 1.63 3.78 3.78 17.50 7.9450.625 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W1767 2 RH/LH 8 4.38 9.88 23.00 10.4350.500 x 9.250 x 18.625Overlay LH/RH for 6" blades 0.625 x 33.78 3.69 3.69 ...2nd Row0.625 x 0
9W1768 2 RH/LH 8 5.97 9.88 27.10 12.2950.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.625 x 35.38 3.69 3.69 ...2nd Row0.625 x 0
120 K M M2 ALLSerial Number:
8E5529 2 RH/LH 5 1.56 3.78 3.78 16.90 7.6750.625 x 6.000 x 18.250End bit LH/RH 0.750 x 2.5
2322142 2 RH/LH 8 4.37 9.87 6.00 22.70 10.300.500 x 18.626 x 9.252Overlay LH/RH for 6" blades 0.7503.78 3.69 3.69 ...2nd Row0.750
6Y2805 2 RH/LH 8 5.97 9.88 26.90 12.2050.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.750 x 3.255.38 3.69 3.69 ...2nd Row0.750 x 0
130 UP TO 74V2293Serial Number:
7D2052 2 RH/LH 5 1.31 3.94 3.94 14.00 6.3550.500 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W2945 2 RH/LH 5 1.31 3.94 3.94 18.00 8.160.625 x 6.000 x 18.374Heavy Duty End bit LH/RH 0.625 x 2.25
6D1904 2 RH/LH 8 4.31 9.63 22.50 10.2150.500 x 9.250 x 18.250Overlay LH/RH for 6" blades 0.625 x 33.50 3.75 3.75 ...2nd Row0.625 x 0
6D1948 2 RH/LH 8 6.31 9.63 27.70 12.5650.500 x 9.250 x 22.250Overlay LH/RH for 8" blades 0.625 x 35.50 3.75 3.75 ...2nd Row0.625 x 0
4D5757 1 RH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay RH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
4D5758 1 LH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay LH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
130 G H 74V02293-UPSerial Number:
8E5531 1 RH/LH 5 1.63 3.78 3.78 17.50 7.9450.625 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W1767 2 RH/LH 8 4.38 9.88 23.00 10.4350.500 x 9.250 x 18.625Overlay LH/RH for 6" blades 0.625 x 33.78 3.69 3.69 ...2nd Row0.625 x 0
9W1768 2 RH/LH 8 5.97 9.88 27.10 12.2950.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.625 x 35.38 3.69 3.69 ...2nd Row0.625 x 0
14 ALLSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader End Bits and Overlays
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7D2083 1 5 1.38 3.94 3.94 20.60 9.3450.625 x 6.000 x 21.250End bit RH 0.625 x 2.25
7D2084 1 5 1.38 3.94 3.94 21.00 9.5350.625 x 6.000 x 21.250End bit LH 0.625 x 2.25
6D1904 2 RH/LH 8 4.31 9.63 22.50 10.2150.500 x 9.250 x 18.250Overlay LH/RH for 6" blades 0.625 x 33.50 3.75 3.75 ...2nd Row0.625 x 0
6D1948 2 RH/LH 8 6.31 9.63 27.70 12.5650.500 x 9.250 x 22.250Overlay LH/RH for 8" blades 0.625 x 35.50 3.75 3.75 ...2nd Row0.625 x 0
14 G UP TO 96U1-4324Serial Number:
9J4405 1 4 1.38 4.16 4.16 17.90 8.1240.625 x 6.000 x 18.625End bit RH 0.750 x 2.25
9J4406 1 4 1.38 4.16 4.16 17.90 8.1240.625 x 6.000 x 18.625End bit LH 0.750 x 2.25
7D9999 2 RH/LH 8 6.38 10.63 28.90 13.1150.500 x 9.250 x 23.375Overlay LH/RH for 8" blades 0.750 x 3.255.69 4.00 4.00 ...2nd Row0.750 x 0
14 G H M 14G(96U7325-UP) 14H(ALL) 14M(ALL)Serial Number:
8E5529 2 RH/LH 5 1.56 3.78 3.78 16.90 7.6750.625 x 6.000 x 18.250End bit LH/RH 0.750 x 2.5
6Y2805 2 RH/LH 8 5.97 9.88 26.90 12.2050.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.750 x 3.255.38 3.69 3.69 ...2nd Row0.750 x 0
140 UP TO 72V1-9828Serial Number:
7D2052 2 RH/LH 5 1.31 3.94 3.94 14.00 6.3550.500 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W2945 2 RH/LH 5 1.31 3.94 3.94 18.00 8.160.625 x 6.000 x 18.374Heavy Duty End bit LH/RH 0.625 x 2.25
6D1904 2 RH/LH 8 4.31 9.63 22.50 10.2150.500 x 9.250 x 18.250Overlay LH/RH for 6" blades 0.625 x 33.50 3.75 3.75 ...2nd Row0.625 x 0
6D1948 2 RH/LH 8 6.31 9.63 27.70 12.5650.500 x 9.250 x 22.250Overlay LH/RH for 8" blades 0.625 x 35.50 3.75 3.75 ...2nd Row0.625 x 0
4D5757 1 RH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay RH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
4D5758 1 LH 5 6.38 28.70 13.0250.625 x 9.000 x 18.875Overlay LH for 8" Flat Blades 0.625 x 36.38 ...2nd Row0.625 x 0
140 G 72V09829-UPSerial Number:
8E5531 1 RH/LH 5 1.63 3.78 3.78 17.50 7.9450.625 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W1767 2 RH/LH 8 4.38 9.88 23.00 10.4350.500 x 9.250 x 18.625Overlay LH/RH for 6" blades 0.625 x 33.78 3.69 3.69 ...2nd Row0.625 x 0
9W1768 2 RH/LH 8 5.97 9.88 27.10 12.2950.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.625 x 35.38 3.69 3.69 ...2nd Row0.625 x 0
140 143 H BLADE GROUPS 8X8011 AND 8X8016Serial Number:
8E5531 1 RH/LH 5 1.63 3.78 3.78 17.50 7.9450.625 x 6.000 x 18.375End bit LH/RH 0.625 x 2.25
9W1767 2 RH/LH 8 4.38 9.88 23.00 10.4350.500 x 9.250 x 18.625Overlay LH/RH for 6" blades 0.625 x 33.78 3.69 3.69 ...2nd Row0.625 x 0
9W1768 2 RH/LH 8 5.97 9.88 27.10 12.2950.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.625 x 35.38 3.69 3.69 ...2nd Row0.625 x 0
140 143 H BLADE GROUPS 1124520 AND 1124521Serial Number:
8E5529 2 RH/LH 5 1.56 3.78 3.78 16.90 7.6750.625 x 6.000 x 18.250End bit LH/RH 0.750 x 2.5
6Y2805 2 RH/LH 8 5.97 9.88 26.90 12.2050.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.750 x 3.255.38 3.69 3.69 ...2nd Row0.750 x 0
140 K M M2 ALLSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 3©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader End Bits and Overlays
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8E5529 2 RH/LH 5 1.56 3.78 3.78 16.90 7.6750.625 x 6.000 x 18.250End bit LH/RH 0.750 x 2.5
2322142 2 RH/LH 8 4.37 9.87 6.00 22.70 10.300.500 x 18.626 x 9.252Overlay LH/RH for 6" blades 0.7503.78 3.69 3.69 ...2nd Row0.750
6Y2805 2 RH/LH 8 5.97 9.88 26.90 12.2050.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.750 x 3.255.38 3.69 3.69 ...2nd Row0.750 x 0
16 ALLSerial Number:
9J4407 1 4 1.38 4.16 4.16 18.00 8.1640.625 x 6.000 x 18.313End bit RH 0.625 x 2.25
9J4408 1 4 1.38 4.16 4.16 18.00 8.1640.625 x 6.000 x 18.313End bit LH 0.625 x 2.25
7D5193 2 RH/LH 8 6.38 10.63 37.00 16.7850.625 x 9.250 x 23.375Overlay LH/RH for 8" blades 0.625 x 35.69 4.00 4.00 ...2nd Row0.625 x 0
16 G UP TO 93U2777Serial Number:
9D4880 1 4 1.50 4.15 4.15 21.40 9.7140.750 x 6.000 x 18.584End bit RH 0.750 x 2.25
9D4881 1 4 1.50 4.15 4.15 21.40 9.7140.750 x 6.000 x 18.584End bit LH 0.750 x 2.25
7D9999 2 RH/LH 8 6.38 10.63 28.90 13.1150.500 x 9.250 x 23.375Overlay LH/RH for 8" blades 0.750 x 3.255.69 4.00 4.00 ...2nd Row0.750 x 0
16 G H M 16G(93U2778-UP) 16H(ALL) 16M(ALL)Serial Number:
8E5530 2 RH/LH 5 1.19 3.78 3.78 20.00 9.0750.750 x 6.000 x 17.500End bit LH/RH 0.750 x 2.5
6Y2805 2 RH/LH 8 5.97 9.88 26.90 12.2050.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.750 x 3.255.38 3.69 3.69 ...2nd Row0.750 x 0
1380797 1 SHANK 3 122.90 55.752.938 x 10.456 x 28.402Ripper Shank 99.999
6Y0359 1 TOOTH 28.20 12.79R350 Ripper Tooth
1140358 1 PIN 0.53 0.24Heavy Duty Pin
1140359 1 RET 0.06 0.03Heavy Duty Coiled Retainer
160 163 H ALLSerial Number:
8E5529 2 RH/LH 5 1.56 3.78 3.78 16.90 7.6750.625 x 6.000 x 18.250End bit LH/RH 0.750 x 2.5
6Y2805 2 RH/LH 8 5.97 9.88 26.90 12.2050.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.750 x 3.255.38 3.69 3.69 ...2nd Row0.750 x 0
160 M M2 ALLSerial Number:
8E5529 2 RH/LH 5 1.56 3.78 3.78 16.90 7.6750.625 x 6.000 x 18.250End bit LH/RH 0.750 x 2.5
2322142 2 RH/LH 8 4.37 9.87 6.00 22.70 10.300.500 x 18.626 x 9.252Overlay LH/RH for 6" blades 0.7503.78 3.69 3.69 ...2nd Row0.750
6Y2805 2 RH/LH 8 5.97 9.88 26.90 12.2050.500 x 9.250 x 21.813Overlay LH/RH for 8" blades 0.750 x 3.255.38 3.69 3.69 ...2nd Row0.750 x 0
24 H ALLSerial Number:
1093118 2 RH/LH 6 3.14 4.34 4.34 52.00 23.5921.000 x 8.000 x 28.000End bit LH/RH 1.000 x 4.5
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 4©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader Blades by Length and Hole
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
5/8" HOLES Curved CarbonSerial Number:--> 1/2" Thick x 6" Wide
9W2293 C 6 3.00 3.00 12.00 34.00 15.420.500 x 6.000 x 48.0004 Foot 0.625
9W2295 C 7 3.00 3.00 12.00 42.90 19.460.500 x 6.000 x 60.0005 Foot 0.625
9W2297 C 8 3.00 3.00 12.00 51.50 23.360.500 x 6.000 x 72.0006 Foot 0.625
9W2299 C 9 3.00 3.00 12.00 60.10 27.260.500 x 6.000 x 84.0007 Foot 0.625
9W2301 C 10 3.00 3.00 12.00 68.70 31.160.500 x 6.000 x 96.0008 Foot 0.625
4Z8968 11 3.00 3.00 12.00 78.40 35.560.500 x 6.000 x 108.0009 Foot 0.625
9W2303 C 12 3.00 3.00 12.00 86.00 39.010.500 x 6.000 x 120.00010 Foot 0.625
9W2305 C 14 3.00 3.00 12.00 104.00 47.170.500 x 6.000 x 144.00012 Foot 0.625
9W2307 C 16 3.00 3.00 12.00 122.00 55.340.500 x 6.000 x 168.00014 Foot 0.625
--> 1/2" Thick x 8" Wide
9W2309 C 6 3.00 3.00 12.00 48.00 21.770.500 x 8.000 x 48.0004 Foot 0.625
9W2311 C 7 3.00 3.00 12.00 61.00 27.670.500 x 8.000 x 60.0005 Foot 0.625
9W2313 C 8 3.00 3.00 12.00 73.00 33.110.500 x 8.000 x 72.0006 Foot 0.625
9W2315 C 9 3.00 3.00 12.00 86.00 39.010.500 x 8.000 x 84.0007 Foot 0.625
9W2317 C 10 3.00 3.00 12.00 99.20 45.000.500 x 8.000 x 96.0008 Foot 0.625
9W2319 C 12 3.00 3.00 12.00 124.00 56.250.500 x 8.000 x 120.00010 Foot 0.625
9W2321 C 14 3.00 3.00 12.00 149.00 67.590.500 x 8.000 x 144.00012 Foot 0.625
9W2323 C 16 3.00 3.00 12.00 173.00 78.470.500 x 8.000 x 168.00014 Foot 0.625
--> 5/8" Thick x 6" Wide
9W2325 C 6 3.00 3.00 12.00 43.10 19.550.625 x 6.000 x 48.0004 Foot 0.625
7T1640 C 7 3.00 3.00 12.00 53.90 24.450.625 x 6.000 x 60.0005 Foot 0.625
7T1633 C 8 3.00 3.00 12.00 64.90 29.440.625 x 6.000 x 72.0006 Foot 0.625
7T1645 C 9 3.00 3.00 12.00 75.70 34.340.625 x 6.000 x 84.0007 Foot 0.625
7T1632 C 10 3.00 3.00 12.00 86.50 39.240.625 x 6.000 x 96.0008 Foot 0.625
4Z8652 23 3.00 3.00 6.00 1.360.625 x 6.000 x 132.00011 Foot on 6" Centers 0.625
4Z8653 24 3.00 3.00 6.000.625 x 6.000 x 144.00012 Foot on 6" Centers 0.625
1359541 16 3.00 3.00 12.00 154.00 69.850.625 x 6.000 x 168.00014 Foot 0.625
--> 5/8" Thick x 8" Wide
9W2328 C 6 3.00 3.00 12.00 60.00 27.220.625 x 8.000 x 48.0004 Foot 0.625
7T1641 C 7 3.00 3.00 12.00 76.60 34.750.625 x 8.000 x 60.0005 Foot 0.625
7T1636 C 8 3.00 3.00 12.00 91.90 41.690.625 x 8.000 x 72.0006 Foot 0.625
7T1643 C 9 3.00 3.00 12.00 107.40 48.720.625 x 8.000 x 84.0007 Foot 0.625
7T1631 C 10 3.00 3.00 12.00 122.70 55.660.625 x 8.000 x 96.0008 Foot 0.625
--> 3/4" Thick x 6" Wide
9W2331 C 6 3.00 3.00 12.00 52.00 23.590.750 x 6.000 x 48.0004 Foot 0.625
7T1642 C 7 3.00 3.00 12.00 65.20 29.570.750 x 6.000 x 60.0005 Foot 0.625
7T1635 C 8 3.00 3.00 12.00 78.00 35.380.750 x 6.000 x 72.0006 Foot 0.625
7T1644 C 9 3.00 3.00 12.00 91.10 41.320.750 x 6.000 x 84.0007 Foot 0.625
9W2336 C 10 3.00 3.00 12.00 104.10 47.220.750 x 6.000 x 96.0008 Foot 0.625
--> 3/4" Thick x 8" Wide
9W2338 C 6 3.00 3.00 12.00 74.00 33.570.750 x 8.000 x 48.0004 Foot 0.625
9W2340 C 7 3.00 3.00 12.00 92.00 41.730.750 x 8.000 x 60.0005 Foot 0.625
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader Blades by Length and Hole
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
7T1634 C 8 3.00 3.00 12.00 111.40 50.530.750 x 8.000 x 72.0006 Foot 0.625
7T1623 C 9 3.00 3.00 12.00 129.70 58.830.750 x 8.000 x 84.0007 Foot 0.625
7T1630 C 10 3.00 3.00 12.00 148.60 67.400.750 x 8.000 x 96.0008 Foot 0.625
--> 1" Thick x 8" Wide
4T2244CAR-6 13 3.00 3.00 6.00 148.90 67.541.000 x 8.000 x 72.0006 Foot 0.625
4T2242CAR-6 15 3.00 3.00 6.00 173.70 78.791.000 x 8.000 x 84.0007 Foot 0.625
5/8" HOLES Curved Heat-treatedSerial Number:--> 1/2" Thick x 6" Wide
3G8016 C 9 3.00 3.00 6.00 34.00 15.420.500 x 6.000 x 48.0004 Foot 0.625
9J3862 C 11 3.00 3.00 6.00 43.10 19.550.500 x 6.000 x 60.0005 Foot 0.625
8D2786 C 13 3.00 3.00 6.00 51.10 23.180.500 x 6.000 x 72.0006 Foot 0.625
8D2787 C 15 3.00 3.00 6.00 59.60 27.030.500 x 6.000 x 84.0007 Foot 0.625
8J7782 C 17 3.00 3.00 6.00 68.10 30.890.500 x 6.000 x 96.0008 Foot 0.625
--> 1/2" Thick x 8" Wide
3G7965 C 9 3.00 3.00 6.00 49.00 22.230.500 x 8.000 x 48.0004 Foot 0.625
9J3863 C 11 3.00 3.00 6.00 61.00 27.670.500 x 8.000 x 60.0005 Foot 0.625
8D2788 C 13 3.00 3.00 6.00 73.90 33.520.500 x 8.000 x 72.0006 Foot 0.625
8D2789 C 15 3.00 3.00 6.00 86.20 39.100.500 x 8.000 x 84.0007 Foot 0.625
8J8980 C 17 3.00 3.00 6.00 98.60 44.720.500 x 8.000 x 96.0008 Foot 0.625
--> 5/8" Thick x 6" Wide
9W1835 C 5 3.00 3.00 6.00 21.40 9.710.625 x 6.000 x 24.0002 Foot 0.625
7D4508 C 11 3.00 3.00 6.00 53.50 24.270.625 x 6.000 x 60.0005 Foot 0.625
5D9553 C 13 3.00 3.00 6.00 64.40 29.210.625 x 6.000 x 72.0006 Foot 0.625
5D9554 C 15 3.00 3.00 6.00 75.00 34.020.625 x 6.000 x 84.0007 Foot 0.625
8J4043 C 17 3.00 3.00 6.00 85.80 38.920.625 x 6.000 x 96.0008 Foot 0.625
--> 5/8" Thick x 8" Wide
1093137 C 5 3.00 3.00 6.00 30.00 13.610.625 x 8.000 x 24.0002 Foot 0.625
1321088 C 9 3.00 3.00 6.00 60.00 27.220.625 x 8.000 x 48.0004 Foot 0.625
7D4509 C 11 3.00 3.00 6.00 76.10 34.520.625 x 8.000 x 60.0005 Foot 0.625
5D9562 C 13 3.00 3.00 6.00 91.40 41.460.625 x 8.000 x 72.0006 Foot 0.625
5D9561 C 15 3.00 3.00 6.00 106.70 48.400.625 x 8.000 x 84.0007 Foot 0.625
5D9731 C 17 3.00 3.00 6.00 122.00 55.340.625 x 8.000 x 96.0008 Foot 0.625
1321011 0.625 x 8.000 x 144.00012 Foot 0.625
--> 3/4" Thick x 6" Wide
3G7966 C 11 3.00 3.00 6.00 66.30 30.070.750 x 6.000 x 60.0005 Foot 0.625
5D9556 C 13 3.00 3.00 6.00 77.30 35.060.750 x 6.000 x 72.0006 Foot 0.625
5D9557 C 15 3.00 3.00 6.00 90.60 41.100.750 x 6.000 x 84.0007 Foot 0.625
8J4043-6 17 3.00 3.00 6.00 103.60 46.990.750 x 6.000 x 96.0008 Foot 0.625
--> 3/4" Thick x 8" Wide
6G8623 C 4 3.00 3.00 12.00 37.00 16.780.750 x 8.000 x 24.0002 Foot on 12" Centers 0.625
1321087 C 9 3.00 3.00 6.00 73.00 33.110.750 x 8.000 x 48.0004 Foot 0.625
9W6252 C 11 3.00 3.00 6.00 92.00 41.730.750 x 8.000 x 60.0005 Foot 0.625
5D9558 C 13 3.00 3.00 6.00 110.40 50.080.750 x 8.000 x 72.0006 Foot 0.625
5D9559 C 15 3.00 3.00 6.00 128.80 58.420.750 x 8.000 x 84.0007 Foot 0.625
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader Blades by Length and Hole
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
5D9732 C 17 3.00 3.00 6.00 147.70 67.000.750 x 8.000 x 96.0008 Foot 0.625
1957269 19 3.00 3.00 6.00 164.00 74.390.750 x 8.000 x 108.0009 Foot 0.625
--> 1" Thick x 8" Wide
1957178 9 3.00 3.00 6.00 100.00 45.361.000 x 8.000 x 48.0004 Foot 0.625
4T2240 C 11 3.00 3.00 6.00 126.90 57.561.000 x 8.000 x 60.0005 Foot 0.625
4T2244 C 13 3.00 3.00 6.00 147.00 66.681.000 x 8.000 x 72.0006 Foot 0.625
4T2242 C 15 3.00 3.00 6.00 173.70 78.791.000 x 8.000 x 84.0007 Foot 0.625
4T2237 C 17 3.00 3.00 6.00 203.20 92.171.000 x 8.000 x 96.0008 Foot 0.625
5/8" HOLES Flat Heat-treatedSerial Number:--> 5/8" Thick x 8" Wide
4T2967 F 11 3.00 3.00 6.00 76.80 34.840.625 x 8.000 x 60.0005 Foot 0.625
4T2968 F 13 3.00 3.00 6.00 92.20 41.820.625 x 8.000 x 72.0006 Foot 0.625
4T2969 F 15 3.00 3.00 6.00 107.60 48.810.625 x 8.000 x 84.0007 Foot 0.625
4T2966 F 17 3.00 3.00 6.00 122.00 55.340.625 x 8.000 x 96.0008 Foot 0.625
--> 3/4" Thick x 8" Wide
4Z8129-6 7 3.00 3.00 6.00 55.90 25.360.750 x 8.000 x 36.0003 Foot 0.625
4Z8129 5 3.00 3.00 12.00 56.00 25.400.750 x 8.000 x 36.0003 Foot on 12" Centers 0.625
4Z8119-6 9 3.00 3.00 6.00 74.60 33.840.750 x 8.000 x 48.0004 Foot 0.625
4Z8119 F 6 3.00 3.00 12.00 60.00 27.220.750 x 8.000 x 48.0004 Foot on 12" Centers 0.625
4T3034 F 11 3.00 3.00 6.00 93.30 42.320.750 x 8.000 x 60.0005 Foot 0.625
4T3007 F 13 3.00 3.00 6.00 112.10 50.850.750 x 8.000 x 72.0006 Foot 0.625
4T3036 F 15 3.00 3.00 6.00 130.80 59.330.750 x 8.000 x 84.0007 Foot 0.625
4T3035 F 17 3.00 3.00 6.00 149.50 67.810.750 x 8.000 x 96.0008 Foot 0.625
--> 1" Thick x 8" Wide
1359692 F 9 3.00 3.00 6.00 101.00 45.811.000 x 8.000 x 48.0004 Foot 0.625
7T3497 F 11 3.00 3.00 6.00 126.50 57.381.000 x 8.000 x 60.0005 Foot 0.625
7T3499 F 13 3.00 3.00 6.00 151.70 68.811.000 x 8.000 x 72.0006 Foot 0.625
7T3498 F 15 3.00 3.00 6.00 177.10 80.331.000 x 8.000 x 84.0007 Foot 0.625
7T3496 F 17 3.00 3.00 6.00 202.50 91.851.000 x 8.000 x 96.0008 Foot 0.625
5/8" HOLES Curved Serrated Heat-treatedSerial Number:--> 3/4" Thick x 8" Wide
8D3428 CS 9 3.00 3.00 6.00 57.10 25.900.750 x 8.000 x 48.0004 Foot 0.625
8D3429 CS 11 3.00 3.00 6.00 71.40 32.390.750 x 8.000 x 60.0005 Foot 0.625
1321072 CS 13 3.00 3.00 6.00 85.70 38.870.750 x 8.000 x 72.0006 Foot 0.625
4Z9020 CS 15 3.00 3.00 6.00 100.00 45.360.750 x 8.000 x 84.0007 Foot 0.625
1321073 CS 17 3.00 3.00 6.00 146.00 66.220.750 x 8.000 x 96.0008 Foot 0.625
3/4" HOLES Curved CarbonSerial Number:--> 1/2" Thick x 6" Wide
9W2294 C 6 3.00 3.00 12.00 34.00 15.420.500 x 6.000 x 48.0004 Foot 0.750
9W2296 C 11 3.00 3.00 6.00 42.20 19.140.500 x 6.000 x 60.0005 Foot 0.750
9W2298 C 8 3.00 3.00 12.00 52.00 23.590.500 x 6.000 x 72.0006 Foot 0.750
9W2300 C 9 3.00 3.00 12.00 61.00 27.670.500 x 6.000 x 84.0007 Foot 0.750
9W2302 C 10 3.00 3.00 12.00 69.00 31.300.500 x 6.000 x 96.0008 Foot 0.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 3©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader Blades by Length and Hole
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9W2304 C 12 3.00 3.00 12.00 86.00 39.010.500 x 6.000 x 120.00010 Foot 0.750
9W2306 C 14 3.00 3.00 12.00 104.00 47.170.500 x 6.000 x 144.00012 Foot 0.750
9W2308 C 16 3.00 3.00 12.00 122.00 55.340.500 x 6.000 x 168.00014 Foot 0.750
--> 1/2" Thick x 8" Wide
9W2310 C 6 3.00 3.00 12.00 49.00 22.230.500 x 8.000 x 48.0004 Foot 0.750
9W2312 C 7 3.00 3.00 12.00 61.00 27.670.500 x 8.000 x 60.0005 Foot 0.750
9W2314 C 8 3.00 3.00 12.00 73.00 33.110.500 x 8.000 x 72.0006 Foot 0.750
9W2316 C 9 3.00 3.00 12.00 86.00 39.010.500 x 8.000 x 84.0007 Foot 0.750
9W2318 C 10 3.00 3.00 12.00 98.00 44.450.500 x 8.000 x 96.0008 Foot 0.750
9W2320 C 12 3.00 3.00 12.00 123.30 55.930.500 x 8.000 x 120.00010 Foot 0.750
9W2322 C 14 3.00 3.00 12.00 149.00 67.590.500 x 8.000 x 144.00012 Foot 0.750
9W2324 C 16 3.00 3.00 12.00 173.00 78.470.500 x 8.000 x 168.00014 Foot 0.750
--> 5/8" Thick x 6" Wide
9W2326 C 6 3.00 3.00 12.00 43.00 19.500.625 x 6.000 x 48.0004 Foot 0.750
9W2327 C 7 3.00 3.00 12.00 54.00 24.490.625 x 6.000 x 60.0005 Foot 0.750
7T1637 C 8 3.00 3.00 12.00 64.60 29.300.625 x 6.000 x 72.0006 Foot 0.750
7T1626 C 9 3.00 3.00 12.00 75.70 34.340.625 x 6.000 x 84.0007 Foot 0.750
7T1629 C 10 3.00 3.00 12.00 86.20 39.100.625 x 6.000 x 96.0008 Foot 0.750
--> 5/8" Thick x 8" Wide
9W2329 C 6 3.00 3.00 12.00 60.00 27.220.625 x 8.000 x 48.0004 Foot 0.750
9W2330 C 7 3.00 3.00 12.00 76.00 34.470.625 x 8.000 x 60.0005 Foot 0.750
7T1639 C 8 3.00 3.00 12.00 91.70 41.590.625 x 8.000 x 72.0006 Foot 0.750
7T1624 C 9 3.00 3.00 12.00 107.40 48.720.625 x 8.000 x 84.0007 Foot 0.750
7T1628 C 10 3.00 3.00 12.00 122.80 55.700.625 x 8.000 x 96.0008 Foot 0.750
--> 3/4" Thick x 6" Wide
9W2332 C 6 3.00 3.00 12.00 52.00 23.590.750 x 6.000 x 48.0004 Foot 0.750
9W2333 C 7 3.00 3.00 12.00 67.00 30.390.750 x 6.000 x 60.0005 Foot 0.750
9W2334 C 8 3.00 3.00 12.00 80.00 36.290.750 x 6.000 x 72.0006 Foot 0.750
9W2335 C 9 3.00 3.00 12.00 90.70 41.140.750 x 6.000 x 84.0007 Foot 0.750
9W2337 C 10 3.00 12.00 12.00 104.00 47.170.750 x 6.000 x 96.0008 Foot 0.750
--> 3/4" Thick x 8" Wide
9W2339 C 6 3.00 3.00 12.00 74.00 33.570.750 x 8.000 x 48.0004 Foot 0.750
9W2341 C 7 3.00 3.00 12.00 92.00 41.730.750 x 8.000 x 60.0005 Foot 0.750
7T1638 C 8 3.00 3.00 12.00 111.00 50.350.750 x 8.000 x 72.0006 Foot 0.750
7T1625 C 9 3.00 3.00 12.00 129.60 58.790.750 x 8.000 x 84.0007 Foot 0.750
7T1627 C 10 3.00 3.00 12.00 148.10 67.180.750 x 8.000 x 96.0008 Foot 0.750
--> 1" Thick x 8" Wide
4T2231CAR-6 13 3.00 3.00 6.00 148.00 67.131.000 x 8.000 x 72.0006 Foot 0.750
4T2233CAR-6 15 3.00 3.00 6.00 176.80 80.201.000 x 8.000 x 84.0007 Foot 0.750
4T2236CAR-6 17 3.00 3.00 6.00 202.10 91.671.000 x 8.000 x 96.0008 Foot 0.750
3/4" HOLES Curved Heat-treatedSerial Number:--> 1/2" Thick x 6" Wide
9J3660 C 13 3.00 3.00 6.00 52.00 23.590.500 x 6.000 x 72.0006 Foot 0.750
9J3659 C 15 3.00 3.00 6.00 61.00 27.670.500 x 6.000 x 84.0007 Foot 0.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 4©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader Blades by Length and Hole
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
9J3656 C 17 3.00 3.00 6.00 67.60 30.660.500 x 6.000 x 96.0008 Foot 0.750
--> 1/2" Thick x 8" Wide
1356738 C 9 3.00 3.00 6.00 49.00 22.230.500 x 8.000 x 48.0004 Foot 0.750
1341779 C 11 3.00 3.00 6.00 60.00 27.220.500 x 8.000 x 60.0005 Foot 0.750
3G1626 C 13 3.00 3.00 6.00 74.00 33.570.500 x 8.000 x 72.0006 Foot 0.750
3G1627 C 15 3.00 3.00 6.00 85.50 38.780.500 x 8.000 x 84.0007 Foot 0.750
3G1628 C 17 3.00 3.00 6.00 98.00 44.450.500 x 8.000 x 96.0008 Foot 0.750
--> 5/8" Thick x 6" Wide
9J3657 C 13 3.00 3.00 6.00 63.80 28.940.625 x 6.000 x 72.0006 Foot 0.750
9J3658 C 15 3.00 3.00 6.00 74.50 33.790.625 x 6.000 x 84.0007 Foot 0.750
9J3655 C 17 3.00 3.00 6.00 86.00 39.010.625 x 6.000 x 96.0008 Foot 0.750
--> 5/8" Thick x 8" Wide
3G2166 C 5 3.00 3.00 6.00 31.00 14.060.625 x 8.000 x 24.0002 Foot 0.750
1341773 C 9 3.00 3.00 6.00 60.60 27.490.625 x 8.000 x 48.0004 Foot 0.750
9J7701 C 13 3.00 3.00 6.00 92.00 41.730.625 x 8.000 x 72.0006 Foot 0.750
7D1158 C 15 3.00 3.00 6.00 106.10 48.130.625 x 8.000 x 84.0007 Foot 0.750
8J9821 C 17 3.00 3.00 6.00 121.80 55.250.625 x 8.000 x 96.0008 Foot 0.750
--> 3/4" Thick x 6" Wide
4Z8785 C 15 3.00 3.00 6.00 90.00 40.820.750 x 6.000 x 84.0007 Foot 0.750
--> 3/4" Thick x 8" Wide
3G2165 C 5 3.00 3.00 6.00 38.00 17.240.750 x 8.000 x 24.0002 Foot 0.750
1093124 C 9 3.00 3.00 6.00 73.00 33.110.750 x 8.000 x 48.0004 Foot 0.750
1441293 11 3.00 3.00 6.00 91.00 41.280.750 x 8.000 x 60.0005 Foot 0.750
4Z8131 C 7 3.00 3.00 12.00 92.50 41.960.750 x 8.000 x 60.0005 Foot on 12" Centers 0.750
7D1576 C 13 3.00 3.00 6.00 111.30 50.480.750 x 8.000 x 72.0006 Foot 0.750
7D1577 C 15 3.00 3.00 6.00 128.20 58.150.750 x 8.000 x 84.0007 Foot 0.750
7D1949 C 17 3.00 3.00 6.00 146.50 66.450.750 x 8.000 x 96.0008 Foot 0.750
--> 1" Thick x 8" Wide
1093150 C 9 3.00 3.00 6.00 100.90 45.771.000 x 8.000 x 48.0004 Foot 0.750
4T2231 C 13 3.00 3.00 6.00 148.00 67.131.000 x 8.000 x 72.0006 Foot 0.750
4T2233 C 15 3.00 3.00 6.00 172.80 78.381.000 x 8.000 x 84.0007 Foot 0.750
4T2236 C 17 3.00 3.00 6.00 196.00 88.901.000 x 8.000 x 96.0008 Foot 0.750
--> 1" Thick x 10" Wide
100103CUR3 7 2.94 3.00 6.00 95.60 43.361.000 x 10.000 x 35.8753 Foot 0.750
100104CUR3 9 2.94 3.00 6.00 127.70 57.921.000 x 10.000 x 47.8754 Foot 0.750
--> 1-3/8" Thick x 10" Wide
138103CUR3 7 2.94 3.00 6.00 139.00 63.051.375 x 10.000 x 35.8753 Foot 0.750
138104CUR3 9 2.94 3.00 6.00 185.70 84.231.375 x 10.000 x 47.8754 Foot 0.750
--> 1-1/8" Thick x 13" Wide
118133CUR3 1.125 x 13.000 x 35.8753 Foot 0.750
118134CUR3 9 3.00 3.00 6.00 191.90 87.041.125 x 13.000 x 45.8754 Foot 0.750
--> 1-3/8" Thick x 13" Wide
138133CUR3 1.375 x 13.000 x 35.8753 Foot 0.750
138134CUR3 C 9 2.88 3.00 6.00 233.30 105.821.375 x 13.000 x 47.7504 Foot 0.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 5©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader Blades by Length and Hole
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
--> 1-3/4" Thick x 13" Wide
134133CUR3 7 2.88 3.00 6.00 221.20 100.331.750 x 13.000 x 35.7503 Foot 0.750
134134CUR3 C 9 2.88 3.00 6.00 295.70 134.131.750 x 13.000 x 47.7504 Foot 0.750
3/4" HOLES Flat Heat-treatedSerial Number:--> 5/8" Thick x 8" Wide
4Z8120 F 11 3.00 3.00 6.00 76.40 34.650.625 x 8.000 x 60.0005 Foot 0.750
4T2971 F 13 3.00 3.00 6.00 92.00 41.730.625 x 8.000 x 72.0006 Foot 0.750
4T2970 F 15 3.00 3.00 6.00 106.90 48.490.625 x 8.000 x 84.0007 Foot 0.750
4T9603 F 17 3.00 3.00 6.00 122.40 55.520.625 x 8.000 x 96.0008 Foot 0.750
--> 3/4" Thick x 8" Wide
4T3033 F 13 3.00 3.00 6.00 111.50 50.580.750 x 8.000 x 72.0006 Foot 0.750
4T3032 F 15 3.00 3.00 6.00 130.10 59.010.750 x 8.000 x 84.0007 Foot 0.750
4T3037 F 17 3.00 3.00 6.00 148.70 67.450.750 x 8.000 x 96.0008 Foot 0.750
--> 1" Thick x 8" Wide
4Z8926 F 9 3.00 3.00 6.00 100.00 45.361.000 x 8.000 x 48.0004 Foot 0.750
7T3493 F 13 3.00 3.00 6.00 150.80 68.401.000 x 8.000 x 72.0006 Foot 0.750
7T3494 F 15 3.00 3.00 6.00 176.20 79.921.000 x 8.000 x 84.0007 Foot 0.750
7T3495 F 17 3.00 3.00 6.00 201.20 91.261.000 x 8.000 x 96.0008 Foot 0.750
--> 1" Thick x 10" Wide
4T6502 F 13 3.00 3.00 6.00 186.00 84.371.000 x 10.000 x 72.000 0.750
4T6508 F 15 3.00 3.00 6.00 217.00 98.431.000 x 10.000 x 84.0007 Foot 0.750
4T6511 F 17 3.00 3.00 6.00 248.10 112.541.000 x 10.000 x 96.0008 Foot 0.750
--> 1-3/8" Thick x 10" Wide
4T8316 F 15 2.91 3.00 6.00 306.80 139.161.375 x 10.000 x 83.8137 Foot 0.750
4T8317 F 17 2.94 3.00 6.00 346.50 157.171.375 x 10.000 x 95.8758 Foot 0.750
--> 1-3/4" Thick x 10" Wide
1043628 F 17 2.88 3.00 6.00 442.50 200.711.750 x 10.000 x 95.7508 Foot 0.750
--> 1" Thick x 11" Wide
1406790 15 2.91 3.00 6.00 253.00 114.761.000 x 11.000 x 83.8137 Foot 0.750
4Z9186 17 2.94 3.00 6.00 289.30 131.221.000 x 11.000 x 95.8758 Foot 0.750
--> 1-3/8" Thick x 11" Wide
1321086 400.00 181.441.375 x 11.000 x 95.8138 Foot 0.750
--> 1-3/8" Thick x 12" Wide
4Z9188 413.00 187.331.375 x 12.000 x 95.8138 Foot 0.750
--> 1-3/4" Thick x 13" Wide
D26515 15 2.88 3.00 6.00 479.00 217.271.750 x 13.000 x 83.7507 Foot 0.750
1282577 F 17 2.88 3.00 6.00 532.00 241.311.750 x 13.000 x 95.7508 Foot 0.750
3/4" HOLES Curved Serrated Heat-treatedSerial Number:--> 3/4" Thick x 8" Wide
8J8255 CS 9 3.00 3.00 6.00 60.00 27.220.750 x 8.000 x 48.0004 Foot 0.750
8J8256 CS 11 3.00 3.00 6.00 76.00 34.470.750 x 8.000 x 60.0005 Foot 0.750
--> 1" Thick x 8" Wide
4T3512 CS 9 3.00 3.00 6.00 77.10 34.971.000 x 8.000 x 48.0004 Foot 0.750
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 6©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader Blades by Length and Hole
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
4T3511 CS 11 3.00 3.00 6.00 96.50 43.771.000 x 8.000 x 60.0005 Foot 0.750
3/4" HOLES Flat Serrated Heat-treatedSerial Number:--> 1" Thick x 8" Wide
7T3600 FS 9 3.00 3.00 6.00 82.00 37.191.000 x 8.000 x 48.0004 Foot 0.750
7T3601 FS 11 3.00 3.00 6.00 102.60 46.541.000 x 8.000 x 60.0005 Foot 0.750
--> 1" Thick x 10" Wide
4T8800 FS 9 3.00 3.00 6.00 99.10 44.951.000 x 10.000 x 48.0004 Foot 0.750
4T8801 FS 11 3.00 3.00 6.00 124.00 56.251.000 x 10.000 x 60.0005 Foot 0.750
4Z8055 FS 15 3.00 3.00 6.00 215.00 97.521.000 x 10.000 x 84.0007 Foot 0.750
4Z8056 FS 17 3.00 3.00 6.00 201.10 91.221.000 x 10.000 x 96.0008 Foot 0.750
--> 1-3/8" Thick x 10" Wide
4Z8346 FS 15 3.00 3.00 6.00 233.20 105.781.375 x 10.000 x 84.0007 Foot 0.750
1004581 FS 17 3.00 3.00 6.00 280.80 127.371.375 x 10.000 x 95.8128 Foot 0.750
--> 1-3/4" Thick x 10" Wide
1043631 FS 17 3.00 3.00 6.00 364.00 165.111.750 x 10.000 x 95.8138 Foot 0.750
--> 1-3/4" Thick x 13" Wide
1341778 FS 17 2.94 3.00 6.00 421.00 190.961.750 x 13.000 x 95.8758 Foot 0.750
1" HOLES Curved Heat-treatedSerial Number:--> 1-1/8" Thick x 13" Wide
1093117CUR C 9 2.94 3.00 6.00 183.00 83.011.125 x 13.000 x 47.8754 Foot 1.000
--> 1-3/8" Thick x 13" Wide
138134CUR1 1.375 x 13.000 x 47.8754 Foot 1.000
--> 1-3/4" Thick x 13" Wide
1093116CUR C 9 2.94 3.00 6.00 292.00 132.451.750 x 13.000 x 47.8754 Foot 1.000
1" HOLES Flat Heat-treatedSerial Number:--> 1-1/8" Thick x 13" Wide
1093117 F 9 2.94 3.00 6.00 183.90 83.421.125 x 13.000 x 47.8754 Foot 1.000
--> 1-3/4" Thick x 13" Wide
1093116 F 9 3.00 3.00 6.00 291.10 132.041.750 x 13.000 x 47.8754 Foot 1.000
--> 2-1/2" Thick x 13" Wide
1321019 F 9 2.88 3.00 6.00 406.00 184.162.500 x 13.000 x 47.7504 Foot 1.000
--> 1-1/8" Thick x 16" Wide
1359690 F 9 3.00 3.00 6.00 223.00 101.151.125 x 16.000 x 47.7504 Foot 1.000
--> 1-3/4" Thick x 16" Wide
1386440 F 9 2.88 3.00 6.00 356.90 161.891.750 x 16.000 x 47.7504 Foot 1.000
--> 2-3/8" Thick x 16" Wide
1359349 F 9 2.88 3.00 6.00 486.80 220.812.375 x 16.000 x 47.7504 Foot 1.000
--> 3" Thick x 16" Wide
1359576 F 9 3.00 3.00 6.00 632.00 286.673.000 x 16.000 x 47.7504 Foot 1.000
1" HOLES Flat Serrated Heat-treatedSerial Number:
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 7©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Grader Blades by Length and Hole
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
--> 1-3/4" Thick x 13" Wide
1386542 FS 9 3.00 3.00 6.00 210.50 95.481.750 x 13.000 x 47.7504 Foot 1.000
--> 2-1/2" Thick x 13" Wide
1324753 FS 9 3.00 3.00 6.00 358.00 162.392.500 x 13.000 x 47.7504 Foot 1.000
--> 2-3/8" Thick x 16" Wide
1359796 FS 9 2.88 3.00 6.00 385.60 174.912.375 x 16.000 x 47.7504 Foot 1.000
--> 3" Thick x 16" Wide
1359797 FS 9 3.00 3.00 6.00 563.00 255.373.000 x 16.000 x 47.7504 Foot 1.000
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 8©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Plow bolts, nuts and washers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
ALL Serial Number:4F3664 0.625 x x 1.500Plow Bolt
4F3653 0.625 x x 1.750Plow Bolt
4F3654 0.625 x x 2.000Plow Bolt
3F5108 0.625 x x 2.250Plow Bolt
4F3656 0.625 x x 2.500Plow Bolt
4F3657 0.625 x x 2.750Plow Bolt
4F3658 0.625 x x 3.000Plow Bolt
4F3665 0.625 x x 3.500Plow Bolt
4F0391 0.625 x x 3.750Plow Bolt
4F3671 0.625 x x 4.000Plow Bolt
4K0367 0.625 x x Nut
5P8247 0.625 x x Washer
4F3672 0.750 x x 2.000Plow Bolt
4F7827 0.750 x x 2.250Plow Bolt
5J4773 0.750 x x 2.500Plow Bolt
5J4771 0.750 x x 2.750Plow Bolt
1J6762 0.750 x x 3.250Plow Bolt
5F8933 0.750 x x 3.750Plow Bolt
1J0962 0.750 x x 4.250Plow Bolt
1J6761 0.750 x x 4.625Plow Bolt
5P6783 0.750 x x 6.000Plow Bolt
5P6784 0.750 x x 7.000Plow Bolt
2J3506 0.750 x x Nut
5P8248 0.750 x x Washer
5J4772 0.875 x x 2.500Plow Bolt
6F0196 0.875 x x 2.750Plow Bolt
5J2409 0.875 x x 3.000Plow Bolt
8J2935 0.875 x x 3.250Plow Bolt
2J2548 0.875 x x 3.500Plow Bolt
2J5458 0.875 x x 4.250Plow Bolt
1J0849 0.875 x x 4.625Plow Bolt
2J3505 0.875 x x Nut
5P8249 0.875 x x Washer
3J2801 1.000 x x 2.500Plow Bolt
1J5607 1.000 x x 2.750Plow Bolt
4F4042 1.000 x x 3.000Plow Bolt
4J9058 1.000 x x 3.250Plow Bolt
4J9208 1.000 x x 3.500Plow Bolt
8J2928 1.000 x x 3.750Plow Bolt
5P8136 1.000 x x 4.000Plow Bolt
1J3527 1.000 x x 4.500Plow Bolt
1J4947 1.000 x x 5.250Plow Bolt
2J3507 1.000 x x Nut
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 1©2013 Black Cat Blades, Ltd.
Black Cat Blades Ltd. Plow bolts, nuts and washers
Black Cat Replacement Parts For®Caterpillar Equipment
Model/Part Number
BladeType
QtyReqBlade Position
Dimensions. . . . . . . . TotalHoles Qty Dia x Len
Bolts. . . . . . . .1st to 2End to 1
Hole Spacing. . . . . . . .2nd to 3
Weight. . . . . .KgLbsThick Width Length
8J2933 1.000 x x Conical Nut
5P8250 1.000 x x Washer
8T9079 1.250 x x 3.250Plow Bolt
6V6535 1.250 x x 3.750Plow Bolt
5P8823 1.250 x x 4.125Plow Bolt
6V8360 1.250 x x 4.500Plow Bolt
5P8361 1.250 x x 4.938Plow Bolt
1981092 1.250 x x 5.500Plow Bolt
2099311 1.250 x x 6.563Plow Bolt
3K9770 1.250 x x Nut
5P8362 1.250 x x Conical Nut
4K0684 1.250 x x Washer
, and other identities and/or trademarks referred to in this publication are the registered marks of the entitiesnoted herein. The use of any trademarks of others than Black Cat Blades Ltd. are solely and exclusively for identification, informational,Caterpillar , Komatsu® ®
make, use, or sell any products manufactured by any such entity identified in this publication.comparative, and descriptive purposes. Black Cat Blades Ltd. is not affiliated with any owner of such registered marks and does not
Page 2©2013 Black Cat Blades, Ltd.
Top Related